Model 1175 Hurricane Sliding Door System

Transcription

Nabco Entrances Inc.
S82 W18717 Gemini Drive
PO Box 906
Muskego, WI 53150
Phone: 877-622-2694
Fax:
888-679-3319
www.nabcoentrances.com
Automatic
Entrance
Systems
Model 1175
(H60-Narrow)
Hurricane Sliding Door System
**Dade County Approved**
WARNING
● Turn OFF all power to the Automatic Door if a Safety System is not working.
● Instruct the Owner to keep power turned OFF until corrective action can be achieved by a NABCO trained
technician. Failure to follow these practices may result in serious consequences.
● NEVER leave a Door operating without all Safety detection systems operational.
P/N 14-10275
December 30, 2014 Revision
Installation Manual
P/N 14-10275
Model 1175 (H60-Narrow)
Hurricane Slide Door System
Safety Practices
WARNING:
Do not install, operate or service this product unless you have read and understand the Safety Practices,
Warnings, Installation and Operating Instructions contained in this manual. Failure to do so may result in
property damage or personal injury.
WARNING:
Turn OFF all power to the Automatic Door if a Safety System is not working.
Instruct the Owner to keep all power turned OFF until corrective action can be achieved by a NABCO
trained technician. Failure to follow these practices may result in serious consequences
NEVER leave a Door operating without all Safety detection systems operational.
CAUTION:
Read these safety practices before installing, operating or servicing the sliding door. Failure to follow
these practices may result in serious consequences.
Read, study and understand the operating instructions contained in or referenced in this manual before
operating the sliding door. If you do not understand the instructions, ask the installing qualified
technician to teach you how to use the sliding door.
This manual and the owners’ manual must be given to and retained by the purchasing facility or end
user.
1. If the door appears broken or does not seem to work correctly, it should be immediately removed
from service and a qualified technician contacted for corrective action.
2. Disconnect power at the fused disconnect during all electrical or mechanical service. When
uncertain whether power supply is disconnected, always verify using voltmeter.
3. All electrical troubleshooting or service must be performed by qualified electrical technicians
and must comply with all applicable governing agency codes.
4. It is the responsibility of the installing door technician to install all warning and instructional
labels in accordance with ANSI A156.10.
5. It is the responsibility of the purchasing facility or end user to keep warning instructional labels
and literature legible, intact, and with the door.
6. Replacement labels and literature may be obtained from local NABCO Entrances, Inc.
distributors. If the name of the local distributor is unknown, contact NABCO Entrances, Inc. at
(877-622-2694) for assistance.
7. Do not place fingers or uninsulated tools inside the electrical control box. Touching wires or
other parts inside the enclosure may cause electrical shock, serious injury or death.
2
877-622-2694 – www.nabcoentrances.com
NABCO
ENTRANCES INC.
P/N 14-10275
Safety Practices
3
NABCO
ENTRANCES INC.
P/N 14-10275
Contents
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Rough Opening (RO) Preparation
Framing and Header Assembly
Installation of Track
Glass Handling and Installation
Installation of Swing Panel(s)
Installation of Fixed Panel(s)
Installation of Sliding Door(s)
Adjusting of Door
Adjusting Door Preload
Adjustment of Interlocks
Installation of Bottom Guide
Adjusting Belt Tension
Belt Alignment
Installation of Bottom Sweep Vinyl
Door Panic Adjustment and Verification of Breakout Magnet Installation
Mounting of Accusensors
Typical Slider Wiring
Microprocessor Controller
Holding Beams
Electric Lock
Electrical Information
Troubleshooting
Common Replacement Parts
Wiring Diagrams
Y. Return Policy
Z. Appendix
4
5
6
7
8-9
10
11
12
13
14
15
15
16
16
17
18
19
19
19
19
20
21
22
23-28
29
30-42
TOOL LIST
½” Wrench: Box or Open End (2 required)
15/16” Open End Wrench
3/8” Drive Socket Wrench
7/16” Socket
6” Socket Extension
Allen Wrenches 3/32”, 1/8”, 3/16”
Phillips Screwdrivers: #2 and #3
Slotted Screwdriver: Large
4
Hand Drill: Electric or Cordless
Drill: 1/8”
7/32”
¼” Masonry
3/8” by 82 Deg. Countersink
Level: (Laser Type Preferred)
Tape Measure
Broom
NABCO
ENTRANCES INC.
P/N 14-10275
A. Rough Opening (RO) Preparation
1. Check floor across entire opening. Make sure installation area is level and clear of debris.
2. RO height should be door height plus ¼” per side. (Allow for tile or other materials that may change
floor height.)
3. RO width should be total door width plus ¼” per side. (See Figure 1)
RO Width
90°
1/4"
90°
RO Height
1/4"
Finished Floor
1/4"
Figure 1: Rough Opening Preparation
5
NABCO
ENTRANCES INC.
P/N 14-10275
B. Framing and Header Installation
1. Place header on a flat surface with removable cover facing up. Protect the header from scratches.
2. Remove two screws from the bottom of the cover. Remove the cover. (See Figure 2) Remove parts
box from header and set aside.
3. Position the jamb tubes on each end of the header. Fasten with the provided ¼-20 x 1 inch bolts into
rivnuts in jambs. (See Figure 3) Refer to label on jamb for proper location.
Back of Header
Cover in
Closed Position
Cover Side of Header
Swing
Up
Cover in
Open Position
Push In to Lock
Rivnuts
1/4-20 Bolts
(6 per side)
Figure 2
Figure 3
Jamb Tube
When not removing cover make
sure that it is locked in securely!
1/4"
Shim and plumb
clearance
CAUTION:
When installing header, keep unprotected pedestrians out of the
area below the header until it is secured to the building. Failure to
do so may result in property damage or personal injury.
4. Lift header and jamb tubes into position.
Jamb
Tube
Note: Unless it was a specially ordered unit, the cover
on the fixed sidelite units with wall track is on the
exterior. On a Full Open unit it is on the interior.
5. Level the header assembly by shimming under the
appropriate jamb if necessary.
6. Plumb one jamb tube in both planes. If required,
shim the back of the jamb. (See Figure 4)
7. When installing this unit it is important to be in
compliance with Dade County Hurricane
specifications for fastening the header and jambs
to the building as specified on the prints in the
Appendix.
8. Plumb and securely fasten the other jamb.
9. Reinstall cover. Install the Handi terminal bracket
under the mounting bolt. (See Figure 5) It should
6
Figure 4
Place Handy Terminal Bracket
under this mounting bolt
NABCO
Nameplate
Figure 5
NABCO
ENTRANCES INC.
P/N 14-10275
1. Snap a chalk line on the floor from jamb to
jamb (See Figure 7) on the interior side of
the building. Note the dimensions shown
are for a Full Open.
2. Floor track is factory cut. Contact
NABCO ENTRANCES customer service
at (877) 622-2694 to order new track.
3. There will be two pieces of threshold for a
Bi-Part and one piece of threshold for a
Single. Both units will come with a Bolt
Lock Plate that will be installed under the
nose of the door panel(s). The Bi-Part
configuration is shown in figure 8.
4. Locate track flush with the chalk line.
Check floor track location with plumb bob
from the header. It should be 1/8” inset
from the header. (See Figure 9)
5. Prior to installation the floor track will
need to be drilled in compliance with Dade
County Hurricane specifications for
fastening the threshold as specified on the
prints in the Appendix.
6. Using the drilled floor track mark the
location of the track holes onto the floor.
Drill the holes using a 3/16-inch masonry
bit. Fasten the track to the floor using ¼”
x 2 ¾” ITW Buildex PFH Tapcons with a
minimum of 1 ¾” embedment in 3500 psi
concrete.
6 1/2
Full open
align with the pryout plug on the NABCO
nameplate.
C. Installation of Track
(Full Open Units ONLY)
Finished floor
Figure 6
Chalk line
1 3/4"
1 3/4"
4 1/2"
4 1/2"
Jamb Tube
4 1/2"
Floor Track
Figure 7
Interior
Bolt Lock Plate
2 filler strips
4 wear stripes
Exterior
SO width
Clear opening
SO width
Figure 8
Header
Cover
side
4 1/2" Jamb
Plumb line +1/8"
to edge of track
1/8"
4 1/2" Track
Full Open
Figure 9
7
NABCO
ENTRANCES INC.
P/N 14-10275
D. Glass Handling and Installation
CAUTION:
Use caution when moving and installing the glass panels. These
panels are constructed with tempered glass. Any sharp objects that
come in contact with the glass may cause the glass to craze. NABCO
Entrances, Inc. is not responsible for broken glass.
1. When glazing the unit the use of a
qualified glazer is required.
2. Be sure that the area surrounding the glass
installation is free of debris and any sharp
objects that could contaminate the glazing
process or damage the glass.
3. The use of approved glazing materials is
required. (See Figure 10)
1/8" Solutia Saflex III G Interlayer
3/16" Tempered Glass
#10 x 2"
@ 12" o.c.
except near
corner @ 3"
o.c.
Glass Stop
Channel
142335
1"
Dlubak Technologies
Laminated/Tempered
Glass (Typical)
Reinforcement 3/4" x 3/4" x 1/8"
Aluminum Angle
Glass Stop
Base
142336
#10 - 24 x PFH
Thread Forming
Staggered 2" From
Each End 4-6" O.C.
1/2" Glass Bite
Dow 995 Silicone
(Typical)
Typical Glazing Detail
Entire Perimeter all Lites
Figure 10
8
NABCO
ENTRANCES INC.
P/N 14-10275
E. Installation of Swing Panel
Jamb
Tube
1. Locate the swing panel pivot in the parts
box.
2. Install the pivot into the jamb by rotating it
into the cutout in the jamb and fastening it
with a 1/4'-20 x ¾ inch screw.
(See Figure 11)
3. Drill thru the barrel of the pivot and into
the track with a 7/32” bit.
4. Install the self-tapping ¼-20 x 1 inch
screw down the barrel of the pivot and into
the track.
5. Install the nylon guide into the barrel of
the pivot.
6. Locate the swing panel. It will have the
ball detent at the top and bottom of the
nose stile.
7. (Full Open Units Only) Remove the
control panel switch assembly from the
panel. (See Figure 12) Save the screws
for reinstallation. Optional key switches
with the same functions are available from
customer service. Descriptions of switch
functions are described in Chart 1.
Control Panel Switches
Floor Track
Figure 11
OFF
ON
NIGHT
Control panel
located in side panel
on operator end of
header
AUTO
ONE WAY
HOLD OPEN
FULL
RED. OPEN
Figure 12
Option
Function
Top
1. ON
2. Off
3. Night
1. Turns the unit on.
2. Turns the unit off.
3. Limits access to the door by turning off the sensors on the door but allowing the door to be
accessed by a push plate, card reader or other source.
Middle
1. One way
2. Auto
3. Hold Open
1. Sets the door to open in only one direction. (Entrance or Exit)
2. Sets the door to open in both directions. (Entrance and Exit)
3. Sets the door to open and remain open.
Bottom
1. Full Open
2. Reduced Open
1. Sets the door to fully open.
2. Sets the door so that it does not open completely.
8. (Full Open Units Only) There are about 4
feet of cable inside the header for the
control panel harness. Withdraw a
sufficient amount of the harness to reach
the control panel switches on the swing
panel.
9. (Full Open Units Only) Route the control
panel wiring harness from the header past
the swing panel top pivot.
(See Figures 13)
9
Swing
Panel
Pivot
Panic
Direction
Pivot Pin
Retracting
Pin
Control Panel Switch
Harness From Header
Figure 13
Sidelight
Panel
NABCO
ENTRANCES INC.
P/N 14-10275
Large Washer
Use as required
E. Installation of Swing Panel (Continued)
10. Position swing panel over bottom pivot.
Note the panic direction and pivot location
in Figure 13.
11. Retract the top pivot by pushing the pin
down and aligning with the hole in the
header.
12. Allow the pivot pin to snap into the hole.
Make sure it fully engages the hole. If
necessary, lift up on the retracting pin with a
screwdriver.
13. (Full Open Unit Only) Pull the control
panel wiring harness through the switch
cutout in the stile. Connect the switch panel
and reinstall with the screws retained earlier.
14. Assemble the limit arm. (See Figure 14)
Rest the wheel of the limit arm inside the
upper rail of the swing panel. Install the
red-coated screw into the factory-drilled
hole on the bottom of the header. Use one
or two large washers as required.
15. Open and close the swing panel several
times, while lifting on the flush bolt handle
enough to make contact with the header and
the floor track, to score both surfaces.
(See Figure 15)
16. Locate the point where the score marks
intersect the first centering groove on the
bottom of the header (closest to the outside
of the header) and the only groove on the
floor track. Drill a 17/32” hole.
(See Figure 16)
Small Washer
Spacer
Red Coated Screw
Figure 14
Flush Bolt
Score Mark
17/32" Hole
Door
Top of Swing Panel
Figure 15
Bottom of Swing Panel
Door
Flush Bolt
Score Mark
17/32" Hole
Figure 16
10
NABCO
ENTRANCES INC.
P/N 14-10275
F. Installation of Fixed Panel
(Fixed S/L units only.)
Header
11
Fixed Sidelite
Sidelite
Mounting
Brackets
Jamb Tube
1. Remove Control Panel Switch
Assembly from the panel. (See Figure
12) Save screws for use during
installation of the panel.
2. There is approximately four feet of
cable secured inside the header for the
control panel harness. Withdraw a
sufficient amount of the harness to
reach the control panel switches on the
fixed panel.
3. Locate the fixed panel near the jamb
tube. Route the control panel harness
from the bottom of the header through
the top of the rear stile and through the
access cutout.
4. Connect the power down harness near
the front edge of the panel to the 2
yellow wire harness from the header.
Push the excess harness back into the
header or hide it in the top rail of the
sidelight.
5. Align the back end of the fixed panel
with the brackets on the jamb tube.
Ensure that no wires are pinched.
(See Figure 17)
6. Position panel on to brackets and
fasten with the provided screws.
7. Remove the bottom guide cavity cover
from the bottom of the stile. Save the
screws for use during the later steps of
panel installation.
8. Install floor bracket into panel with the
color coordinated ¼-20 x ½ inch
screw. Plumb panel and mark holes on
the floor. Drill holes with masonry bit
and fasten the bracket to the floor.
(See Figure 18)
Figure 17
Figure 18
NABCO
ENTRANCES INC.
P/N 14-10275
G. Installation of Sliding Door(s)
4
3
10
Long belt clip used on
bi-parts and all singles
(SHORT ON UNITS
WITH ELECTRIC LOCKS)
Short belt used
on bi-parts only
(LONG WITH
ELECTRIC LOCKS)
2
1
8
1.
2.
3.
4.
5.
Jamb Tube
Power Cut Off Switch
Operator
Control
Belt Clip (Upper)
5
6
7
6.
7.
8.
9.
10.
9
Belt Clip (Lower)
Roller
Anti-riser
Idler
Handy Terminal Connector
Figure 19
Anti-rise
Track
Hanger Roller
Anti-riser
1. Loosen the hanger roller and anti-riser nuts with a
15/16-inch wrench. (See Figure 20)
2. Lift door onto track. Slightly tilting the door
approach angle may be necessary to allow rollers to
catch the track. (See Figure 21)
1/64" - 1/32"
Clearance
Note: If system is a Full Open unit, it will be necessary
to pry up on the bottom guide on the back corner of the
door to allow the door to enter the floor track.
Figure 20
Position
into
track
Anti-riser
Track roller
Lower
panel
CAUTION:
Do not panic door until all
adjustments are made and the
doors are secured.
Lift
panel
Figure 21
12
NABCO
ENTRANCES INC.
P/N 14-10275
H. Adjustment of Door
1. Door height from finished floor is adjustable
from 11/64 inch to 29/64 inch. (See Figure 22)
2. Place a 15/16-inch wrench on the nut of the
roller. With another 15/16-inch open-end
wrench, rotate the bolt clockwise to raise or
lower the door.
Note: Do not rotate the bolt counter clockwise, as this
would unthread the bolt from the roller.
3. Still holding the bolt head, secure the nut
against the door carrier. Repeat this process on
the remaining rollers.
4. The leading edge of the doors should meet with
no gap between the opposite door (or jamb tube
in the case of a single unit) at the top or bottom.
If necessary, adjust the height and angle of the
doors according to Step 2.
5. Slide the anti-risers up in the slot until there is a
1/64-inch to 1/32-inch gap between anti-riser
wheel and anti-riser track. Tighten the nut on
the anti-rise wheel.
6. Attach belt clips(s) using the #12 x ¾ inch selfdrilling/self tapping screws. Starter mounting
holes have been pre-drilled in the door carrier.
The belt clips should be installed toward the
leading edge of the doors. (See Figure 23)
7. Adjust the doorstop so there is a 3/8-inch gap
from the face of the sidelight or swing panel.
(See Figure 24) In some cases, the doorstop
will be mounted on the jamb tube.
11/64" to 29/64" gap from floor
No gaps, panels parallel
Figure 22
Long belt clip used on
bi-parts and all singles
(SHORT ON UNITS
WITH ELECTRIC LOCKS)
Short belt used
on bi-parts only
(LONG WITH
ELECTRIC LOCKS)
Figure 23
3/8" Finger Protection
Sidelight
Panel
Sliding Door
Figure 24
13
NABCO
ENTRANCES INC.
P/N 14-10275
Hanger
I. Adjusting Door Preload
(Glass must be installed before adjusting preload.)
Pivot bar
Preload
adjust screw
1. Panic the door open to check door sag. (See Figure 25)
2. Loosen the two locking bolts on the block inside the top
rail of the door. (See Figure 26)
3. Adjust door sag by rotating the setscrew on the back
edge of the door with a 1/8-inch allen wrench. The
door should latch without having to adjust the panel. A
longer setscrew is provided in the parts box if required.
4. Retighten locking bolts.
Door sag
Preload adjust
Pivot shaft
Pivot block
Figure 25
Do not allow the set
screw to protrude more
than an 1/8" past the end of stile
Preload Block
5/16" adjusting set screw
(if needed a 1/2" set screw
is provided in parts box
located in header carton)
Locking Bolt
Limit Arm
Figure 26
14
NABCO
ENTRANCES INC.
P/N 14-10275
J. Adjustment of Interlocks
(Full Open and Pocketed)
1. Manually close the door(s). If the interlocks
prevent the door(s) from closing, it will be
necessary to move them outward and shim (See
Figure 27) behind them.
2. Panic the door open to access the interlocks.
3. Loosen the mounting screws and slide the interlocks
closer to the edges of the stile. Slide shims under
the interlocks as needed to ensure proper
engagement. (See Figure 28a & 28b) It may be
necessary to remove some brush from the backside
of the interlock with a pair of scissors.
4. When the interlock position is correct, drill a 1/8inch hole through the interlock and into the stile.
Pound a roll pin from the parts box into each hole to
lock the interlock in place.
Figure 27
Shims
Door
Swing
Figure 28a
Shim
1/8" Drill
Roll Pin
Figure 28b
15
NABCO
ENTRANCES INC.
P/N 14-10275
K. Installation of Bottom Guide
(Fixed Sidelight Only)
Left Hand
Bottom Guide
Right Hand
Bottom Guide
1. Locate the bottom guide assembly in the parts
box. (See Figure 29)
Note: There is a right hand and left hand bottom guide
that will correspond to a right and left door.
2. Panic the door open. Attach the bottom guide,
by using the two ¼-20 x 1 inch hex head bolts
and two star washers, to the pivot stile.
(See Figure 30)
3. Rotate the bottom guide, one roller at a time,
into the cavity on the bottom of the fixed
sidelight. Replace the bottom guide cavity
cover removed in section F.
Figure 29
L. Adjusting Belt Tension
Note: Belt tension is factory set and should not require
any adjustment except for unusual circumstances in
header mounting or component adjustment.
1. Loosen the mounting nuts on the idler bracket.
(See Figure 31)
2. Loosen the lock nut on the tension adjustment
screw. Turn the tension adjustment screw to
tighten or loosen the belt. The screw should
push the idler bracket in the header. If the
idler bracket does not move, loosen the two
mounting nuts a few more turns.
3. Tension the belt so it is to approximately the
same tension as received from the factory. It
should not be so taut that it bends the drive or
idler shafts! Tighten the lock nut on the
adjustment screw against the bracket a secure
the mounting nuts.
16
Figure 30
Lock nut
Nut track
Tension adjusting screw
Screw clamp
Belt tension is factory set and should not need adjustment
DO NOT OVERTIGHTEN BELT
Figure 31
NABCO
ENTRANCES INC.
P/N 14-10275
M. Belt Alignment
Note: The alignment of the belt is factory-set. Flanges on the pulleys will compensate for minor misalignments and
keep the belt on the pulleys. If the belt does come off the pulleys, the alignment of the shafts as well as other
installed hardware should be checked.
N. Installation of Bottom Sweep Vinyl
1. Slide the brush into the weathering
extrusions. The excess vinyl should hang
out the end of the holder at the rear of the
door.
2. Locate the “L” shaped weathering on the
outside of the door along the bottom edge
with the vinyl located under the door. (See
Figure 32) The edge of the extrusion
should start just at the curve of the front
edge of the door. Mark the three slots of
the extrusion on the door. Drill three 1/8
inch mounting holes.
3. Mount the weathering on the door face
using #6 x ½ inch self-tapping screws
from parts box.
4. (Full Open Units Only) Locate the straight
extrusions on the outside face of the swing
panel. The shorter vinyl (1/4” tall) should be
installed in the swing panel extrusion. There
should not be any excess vinyl on this
weathering. Mark the mounting holes and
install the panel weathering in the same
manner as the door weathering.
17
SO
SX
Weathering
Figure 32
NABCO
ENTRANCES INC.
P/N 14-10275
O. Door Panic Adjustment and Verification of Breakout Magnet Installation
Note: The panic adjustment should be made after the glass is installed. The weight of the door with
the glass will affect the amount of force required to panic the door open. If the force required to panic
the door is not acceptable, it can be adjusted by performing the following steps.
1. Panic the door open. This may require a
slight lifting force to the door or a slight
hit with a rubber mallet to the top rail
approximately three inches from the nose
of the door. Protect the surface of the door
to prevent damage.
2. Remove the panic block in the top of the
door. (See Figure 33)
3. Loosen the setscrew on the front of the
block.
4. Raise or lower the ball plunger with the
screw on the underside of the block.
Adjust the ball plunger for proper breakout
resistance to meet ANSI A156.10 or local
code.
5. Retighten the setscrew and reinstall into
the door. Repeat if necessary.
6. On a full open unit the magnet is located
inside the top rail of the swing panel. (See
Figure 34) It should line up with the
magnetic reed switch, is a 3/8” dia. black
circle on the bottom of the header.
7. On fixed sidelights, the magnet is installed
inside the top rail of the door. Place a
steel washer on the interior side of the rail
to confirm it is installed. The magnetic
reed switch is installed about eye level in
the leading stile of the sidelight facing
towards the door. (See Figure 35)
1. LOOSEN
SET SCREW
2. ADJUST BALL
PLUNGER
Figure 33
Magnet
Figure 34
Figure 35
18
NABCO
ENTRANCES INC.
P/N 14-10275
P. Mounting of Accusensors
Note: Two identical Accusensors have been provided with your door package. (4 if the door opening is
greater than 72 inches). The header was wired from the factory so that the activation circuitry on
the exterior Accusensor is turned off in One Way Traffic Mode (the safety circuitry remains
active and can not be turned off). The exterior Accusensor is located on the side of the header in
the direction of panic or panel breakout. This can be easily reversed in the field by swapping the
connectors where each Accusensor plugs into the main harness.
1. Locate the two individual Accusensors
that were provided inside the header. The
drilling template can be discarded.
2. Carefully pry off the cover of either
Accusensor. Plug the connector from the
header through the access hole in the
Accusensor and into the connector on the
Accusensor.
3. Use the screws provided inside the
Accusensor (in the screw holes) to mount
the Accusensor in the pre-drilled holes.
(See Figure 36)
4. Re-install the cover and snap it into place.
If it does not snap into place, the
Accusensor has been mounted on to
tightly. Back off on the mounting screws
slightly and try again. If it is not properly
secured, the cover may loosen due to
vibration or wind gusts.
5. Repeat for the other Accusensor on the
other side of the header.
6. To reverse the One Way Traffic Mode,
locate the connectors mating the
Accusensor Harnesses to the control box
harness. They will be located under the
plastic wire cover in the header. Swap the
two connectors and re-secure the plastic
wire cover.
19
Activation
& Safety
Activation
& Safety
(Safety Only
in One Way
Traffic Mode)
Panic
Direction
Figure 36
NABCO
ENTRANCES INC.
P/N 14-10275
Q. Typical Slider Wiring
Wiring diagrams are included in the back of the manual, which reflect the typical primary and secondary
circuits installed at the factory. The low voltage (12VDC) reed switch (panic breakaway) and Accusensor are
easily connected on site using factory-installed connector housings. The factory uses Underwriters
Laboratories’ (UL) Recognized Component wire, terminals and connector housings to manufacture the slider.
Contact the Customer Service Department for assistance with special applications.
R. Microprocessor Controller
The Microprocessor Controller has been designed to control the numerous operating characteristics of the slide
door system including speed, recycling, and door opening width. It will need to be programmed after the
installation is complete. (See the Microprocessor Manual 159000 for more details).
S. Holding Beams (optional)
The holding beams are flush mounted in doorframes, facing each other. A pulsed, infrared light beam is
continuously transmitted across the door opening. Interruption of the beam causes a relay switch closure. This
signal will travel back to the microprocessor controller causing the doors to open and remain open until the
object or person is out of the way. A wiring diagram is included in the back of this manual.
T. Electric Lock (optional)
Electric locks are available in two configurations: fail-safe and fail secure. These locks will prevent someone
from opening the doors until an activation signal is applied to the electric lock. This signal could be from a
remote switch, transmitter, or activation device on the face of the door.
Fail-safe will allow the door to manually slide open if the power to the door unit is interrupted. Fail secure will
not permit the door to be manually opened if power is interrupted. Fail secure cannot be opened until the power
is restored and the lock receives an activation signal. Neither type of electric lock will inhibit the panic
breakout.
Each electric lock is factory installed and wired into the control box. (See Figure 37) The only adjustments
required are minor horizontal alignments of the electric lock bolt with the trailing edge of the belt clip.
Horizontal adjustment is made by moving the electric lock assembly along the nut track inside the header. With
the door in the closed position, move the electric lock until the bolt comes in contact with the belt clip. The less
door travel with the door in this position the better. Secure mounting and adjustment screws and re-check the
bolt and door travel. It is also a good idea to check the rigidity of the transformer mounting. Shipping
vibrations may have loosened the bracket. The transformer is integral to the lock assembly and requires 120
VAC power. A wiring diagram is included at the back of this manual for reference.
Solenoid Pin
Control Board
Transformer
Figure 37
20
NABCO
ENTRANCES INC.
P/N 14-10275
U. Electrical Information
CAUTION: Disconnect all power to the junction box prior to making any connections.
1. Convenient electric service holes have been provided in the
slide header end caps and jamb tubes. An electrician should
route 120 VAC, single phase, 5 amp (minimum) power to the
factory supplied and mounted junction box in the header.
2. The electrician should connect one power hot lead (black) to
the power cut off switch mounted inside the junction box.
Utilizing an appropriate wire nut, the electrician should
connect the common lead (white) to the loose common lead
(white) found inside the junction box. The ground wire
should be connected to the ground screw located in the
bottom of the switch junction box. (See Figure 38)
3. Replace the junction box cover. The unit’s power should
now be activated through the building’s electrical circuit
breaker box. Proceed with performance set-up procedures
outlined in the Microprocessor and Handy Terminal Manual
(P/N 159000).
21
Ground Screw
Figure 38
NABCO
ENTRANCES INC.
P/N 14-10275
V. Troubleshooting
Symptom
Solution
Accusensor does not seem to reach
out far enough
Accusensor is not seeing people
accessing the door from the side.
When the doors are panicked open,
the system does not shut down.
Doors do not move when power is
applied or handy terminal
connected.
Increase the area lever on the side of the Accusensor to a higher number. Increase the opening
speed on the door with the handy terminal.
Turn on more of the area switches on the front of the Accusensor.
The cover on the Accusensor will
not snap on.
Doors move very slowly when the
handy terminal is connected.
The doors do not open completely.
I want to eliminate all outside
switches and sensors and make the
system operate in automatic mode.
I want to reset the system back to
the factory settings.
Door does not run in “ON” but may
run in “OFF”
22
Check the wiring of the power down switch in the fixed panel or bottom of header.
Confirm the swing panel is closed completely. Check the power down magnet in the top rail of
the swing panel is installed and aligned with the magnetic power down switch in the bottom of
the header.
To locate the problem circuit, disconnect the plugs at the Accusensor. The Microprocessor will
ignore any switch or sensor when it is unplugged from circuit.
Install a couple of thin washers to space the Accusensor off from the header and provide
clearance for the cover.
This is normal. It is “learning” the door stroke. After learning the stroke, the handy terminal
will prompt you with options.
Look for obstructions in the track as well as inside the header. Check to make sure that the belt
clips are not hitting something.
Check that the mode switch on the panel is not in “Reduced Opening” mode.
Use the handy terminal and reinitialize the system.
Disconnect the 12 pin connector from inside the microprocessor and install the special
connector jumper tool p/n 115941 into its place.
The system will consist of only the motor, operator and control box (Microprocessor). The
handy terminal will be the only means of operating the door.
1. Plug in handy terminal and wait for door to close.
2. At “Swing/Slide Stroke?” enter YES
3. At “Swing Door Y or N?” enter YES (even though you have a slide door)
4. Door will try to initialize as a swing door and reset the settings.
5. It will prompt you with “Swing/Slide Stroke.” Enter YES
6. At “Swing Door Y or N?” enter NO
7. The system will now initialize as a slide door at the factory settings.
8. You must set the door stroke from the handy terminal from the prompts at this
point.
The holding beam connector (it has a red and white wire in it) in the main harness has a jumper
plug connected to this plug. Remove the jumper. There have been cases where some installers
have incorrectly connected this red/white connector to a blue wire connector. Remove the blue
wire connector and install a jumper into it. The red/white should be empty and any open blue
wire connectors should have a jumper installed.
NABCO
ENTRANCES INC.
P/N 14-10275
W. Common Replacement Parts
Motor alone
219206
EXIT
NIGHT
AUTO
H.O.
REDUCED
FULL
STOP
Operator alone
219530
Motor & Operator assy
229528
GYRO TECH - 248901
Key Switches
219820
No.
Handing
Harness
119208
MICROPROCESSOR CONTROLLER
POWER SOURCE (4P)
NO. COLOR
1
2 WHITE
3 BLACK
4
HANDY TERMINAL (6P)
SENSOR (12P)
USE
EMPTY
115VAC COMMON
115VAC HOT
EMPTY
OPERATOR (6P)
NO.
1
2
3
4
5
6
COLOR
RED
ORANGE
BROWN
BLUE
BLACK
YELLOW
USE
MOTOR V PHASE
ENCODER 12VDC
ENCODER A PHASE
MOTOR U PHASE
ENCODER GND
ENCODER B PHASE
FUSE INSIDE
RATING:125V, 4A
SIZE:5.2 x 20mm
WARNING
For continued protection
against fire, replace only
with same type and rating
of fuse.
CAUTION
1.Please adjust this operator as per instruction manual.
2.Turn the power off, before opening the box.
3.Don't open this box except for replacing fuse.
Otherwise, the warranty will be terminated.
4.Repair of this unit except by Lanson Industries, Inc.
may cause software and hardware malfunction.
NO.
1
2
3
4
SYMBOL
9DC12V
7
61
6B
5 H
6
7
8
9
10
11
12
M0
M1
62
SQ
BA
OUT +
OUT -
COLOR USE [SLIDER/SWINGER]
BROWN 12VDC +
RED
12VDC -,COMMON
BLACK
APPROACH
WHITE
THRESHOLD SENSING
/PRESENCE SENSOR
GREEN REDUCED OPENING
/SAFETY MAT
ORANGE MODE SW1
ORANGE MODE SW2
ORANGE APPROACH(THROUGH)
YELLOW SEQUENTIAL
BLUE
BREAK OUT
VIOLET OUTPUT +
GRAY
OUTPUT -
GYRO TECH
ENTRANCES
LANSON INDUSTRIES
INC.
Microprocessor
Control Box
248901
Door Roller
Assembly
219034
Track Cap
(for damaged track)
149463
Weather Strip
145592-01
Door
Roller/Cover
248830
Anti-Rise
Axle Assembly
219037
Bearing
240787
Left Hand
Fixed Sidelight
Bottom Guide
219046-20
Idler Assembly
229201
Pulley Only
119903
Full Open
Bottom Guide
219053
Right Hand
Roller & Bearing Only
Fixed Sidelight
Bottom Guide Full Open and Fixed Sidelight
149045
219046-10
Figure 39
23
NABCO
ENTRANCES INC.
P/N 14-10275
X. Wiring diagram for connecting push plates or card readers for Night mode.
Attach the normally open contacts across the red and black wire on either the rocker or key switches.
Push buttom switch
during night mode.
EXIT
NIGHT
AUTO
H.O.
Red (#1)
White (#6)
Black (#2)
Red
White
Black
Green
REDUCED
FULL
STOP
Red (#8)
Green (#1)
Blue (#4)
Blue
White
OFF
NIGHT
DOOR OPERATION
ONLY
ON
Blue
Red
Blue
ONE WAY
AUTO
Black
Red
Black
White
Red
Blue
Red
White
Green
Black
HOLD OPEN
FULL
Green
Red
Push buttom switch
during night mode.
REDUCED OPEN
Figure 40
24
NABCO
ENTRANCES INC.
P/N 14-10275
X. Wiring diagram Activation with Night Mode
Closing
contacts
with door
in NIGHT
mode
opens
door.
Blue
Rocker
Switch
Connector
Blue
Black
Red
Orange M1
Orange MO
Green
Blue
Breakaway
Connectors
White
Red
Green
Blue
1175 Microprocessor Wire Diagram
Activation with Night mode.
Connect card reader and wall plate
normally open dry contacts as shown.
Access in the header.
White
Green
Blue
White
Blue
Green
Figure 41
25
NABCO
ENTRANCES INC.
26
AUTO
Black
Rocker Switches
REDUCED OPEN
FULL
Main Breaker
Switch
White
Green
Red
White
Red
Blue
Red
Blue
Black
Green
White
Blue
Red
M.C.
Handy
Terminal
Connector
CN4
Grey
White
Black
Exterior
Accusensor Red
Connector
Brown
Red
Green
Brown
Red
Blue
Blue
Blue
Red
White
Green
White
Green
White
Green
Breakaway
Connectors
Interior Accusensor
Connector
Red
Holding Beam Connector
White
Blue
Black
Blue
Rocker
Switch
Connector
Black
White
Red
Orange M1
Orange MO
Green
Blue
NOTE: In some cases the interior
and exterior Accusensors are reversed
CN3
Purple
Blue
Yellow
Orange 62
Orange M1
Brown
Red
Black
White
Green
Orange MO
Blue
Green
Red
Rocker Switch Extension Harness
1175 Microprocessor Wire Diagram
Motor Plug
CN2
CN1
6
Ground
OFF
HOLD OPEN
DOOR OPERATION
ONLY
120 VAC
Black
Red
Black
ONE WAY
NIGHT
ON
White
P/N 14-10275
X. Microprocessor Wiring Diagram
Figure 42
NABCO
ENTRANCES INC.
P/N 14-10275
X. Wiring Diagram for Fail Safe and Fail Secure Electric Locks
RELAY(DC12V)
GYRO TECH - 248901
No.
MICROPROCESSOR CONTROLLER
POWER SOURCE (4P)
NO. COLOR
1
2 WHITE
3 BLACK
4
OPERATOR (6P)
NO.
1
2
3
4
5
6
COLOR
RED
ORANGE
BROWN
BLUE
BLACK
YELLOW
HANDY TERMINAL (6P)
SENSOR (12P)
USE
EMPTY
115VAC COMMON
115VAC HOT
EMPTY
USE
MOTOR V PHASE
ENCODER 12VDC
ENCODER A PHASE
MOTOR U PHASE
ENCODER GND
ENCODER B PHASE
FUSE INSIDE
RATING:125V, 4A
SIZE:5.2 x 20mm
WARNING
For continued protection
against fire, replace only
with same type and rating
of fuse.
CAUTION
1.Please adjust this operator as per instruction manual.
2.Turn the power off, before opening the box.
3.Don't open this box except for replacing fuse.
Otherwise, the warranty will be terminated.
4.Repair of this unit except by Lanson Industries, Inc.
may cause software and hardware malfunction.
NO.
1
2
3
4
SYMBOL
9DC12V
7
61
6B
5 H
6
7
8
9
10
11
12
M0
M1
62
SQ
BA
OUT +
OUT -
9DC12V (BROWN)
123456789
COLOR USE [SLIDER/SWINGER]
BROWN 12VDC +
RED
12VDC -,COMMON
BLACK
APPROACH
WHITE
THRESHOLD SENSING
/PRESENCE SENSOR
GREEN REDUCED OPENING
/SAFETY MAT
ORANGE MODE SW1
ORANGE MODE SW2
ORANGE APPROACH(THROUGH)
YELLOW SEQUENTIAL
BLUE
BREAK OUT
VIOLET OUTPUT +
GRAY
OUTPUT -
OUT+ (VIOLET)
OUT- (GRAY)
7 (RED)
ENTRANCES
LANSON INDUSTRIES
INC.
Green
Incoming
AC115V
TRANSFORMER
Black
ACTIVATE
ON
SIGNAL
OUTPUT LOCKED
UNLOCKED (ON)
SIGNAL
CLOSED
OPEN >>> CLOSE
DOOR
ELECTRIC LOCK / STRIKE
Solenoid
Yellow
~
Orange
+
-
AC24V
White
time delay(0.25~1sec)
BlackFail Secure Type
Fail Safe Type
Black
GYRO TECH
~
RECTIFIER
Orange
NOTE: LOCK ONLY WORKS IN:
OFF
ONE WAY &
NIGHT
MODES ONLY
LOCKED
CLOSED
time delay(0.25~1sec)
andy Terminal : Aux. Output [0] , time delay [0]~[3]
Mode Input : One Way Traffic Mode or Night Mode
Generic Wiring Diagram for Fail Safe and Fail Secure Electric Locks
Figure 43
27
NABCO
ENTRANCES INC.
P/N 14-10275
X. Holding Beam Wiring Diagram
Telco Brand Safety Beams
Wiring Diagram for Holding Beams for Breakout Shutdown
WHITE
GREEN
GREEN
WIRE NUT
BROWN
ORANGE
BROWN
BLACK
BROWN
BROWN
RED
BLUE
BLUE
BLUE
BROWN
RED
RED
RED
RECEIVER
TRANSMITTER
SMR 3106S
SMT 3000S
BLACK
LIGHT BLUE
BLACK
GREY
GREY
YELLOW
WHITE
GREEN
BLUE
BLACK
"REDUCE"
LEAVE OPEN
BLUE
GREY
GREY
YELLOW
WHITE
GREEN
BLACK
ACUSENSOR
HARNESS
PT. NO. 219246
INTERIOR ACUSENSOR
PT. NO. 148902
EXTERIOR ACUSENSOR
WHITE
PT. NO. 148902
GREEN
MAGNETIC
POWER
DOWN SWITCH
HOLD BEAM PIGTAIL
PT. NO. 229222
PT. NO. 1110188
WHITE
GREEN
Wiring Diagram for Holding Beams as a Safety
WHITE
GREEN
GREEN
BROWN
ORANGE
BROWN
BLACK
BROWN
RED
BLUE
BLUE
BROWN
BROWN
BLUE
RECEIVER
TRANSMITTER
SMR 3106S
SMT 3000S
RED
RED
RED
BLACK
BLACK
"REDUCE"
LEAVE OPEN
LIGHT BLUE
BROWN
GREY
GREY
WHITE
YELLOW
GREEN
PLUG WITH
BLUE JUMPER
(MUST BE
IN PLACE)
BLUE
WHITE
BLACK
GREEN
BLACK
ACUSENSOR
HARNESS
PT. NO. 219246
ACUSENSOR HARNESS
PT. NO. 219246
MAGNETIC POWER
DOWN SWITCH
PT. NO. 229222
BLACK
RECEIVER
TRANSMITTER
SMR 3106S
SMT 3000S
LIGHT BLUE
BLACK
"REDUCE"
LEAVE OPEN
BLUE
EXTERIOR ACUSENSOR
WHITE
PT. NO. 148902
GREEN
MAGNETIC
POWER
DOWN SWITCH
PT. NO. 229222 HOLD BEAM PIGTAIL
PT. NO. 1110188
WHITE
GREEN
BROWN
GREY
GREY
YELLOW
INTERIOR ACUSENSOR
PT. NO. 148902
Holding Beam Wire Diagram P/N 1510194 March 28, 2001
Figure 44
28
NABCO
ENTRANCES INC.
P/N 14-10275
X. Accusensor Wire Path Diagram
Acusensor 2's MUST use 12 VDC (not 24v)
Brown
Gray
Red
1
2
3
4
Yellow
Yellow
1
2
3
4
Gray
24 VAC
Yellow
COM
Yellow
N.O.
AREA SWITCH
ON ON
ON ON
ACUSENSOR
AC / DC
12 ~ 24V
OUTPUT
ON
OFF
mode A
mode C
mode B
mode D
ENTRANCES
AREA LEVER
ON
CONNECTION
GRAY
GRAY
YELLOW
YELLOW
GYRO TECH
MODE SWITCH
INSP.
O.K.
No.
OFF
30 sec.
15 sec.
SENS. [High]
SENS. [Low]
5 min.
90 sec.
1
2
3
4
5
Red
4
3
2
1
Yellow
4
3
2
1
Yellow
Red
Brown
Green
Orange
Brown
or
Red
4
3
2
1
Extension Harness
Exterior Sensor
Black
Interior Sensor
Brown
Main Harness
Mode Input for SW1 and SW2
SW1 SW2
Off Off
Off
On
On
On
On
Off
Results
Auto Mode. Approach and Approach Thru signals available
Electric Lock is always unlocked
Night Mode. None of the activation signals will be accepted.
Sensors provide threshold safety and Electric Lock is always locked.
Full Open Mode. The door keeps the full open point, not affected
by sensors. Electric Lock is always unlocked
One Way Traffic. The interior sensor activates the door, the exterior
sensor provides threshold safety. Electric Lock is locked until
an interior activation is received.
MODE SWITCH TABLE
MO
M1
Mode
Open
Open
Auto
Gnd
Open
Exit
Gnd
Gnd Hold Open
Open
Gnd
Night
Figure 45
29
NABCO
ENTRANCES INC.
P/N 14-10275
Y. NABCO ENTRANCES RETURN POLICY
If it is necessary to return a malfunctioning unit to NABCO, please use the following guidelines:
Return Material Tags (RMT) are to be used for in and out of warranty materials. The RMT is also used for repair
and return as well as return for credit transactions. An RMT must accompany all returned items.
Complete one RMT for each item that will be returned. The following information should be recorded on the tag:
•
•
•
•
•
•
•
•
•
Serial No. or Part No. – Serial numbers for electronic components are stamped, engraved or printed on
stickers and located on the component. Non-electrical parts usually do not have serial numbers.
Part name.
Expiration Date – Expiration dates for electronic components are stamped, engraved or printed on stickers
and located on the component. Non-electrical parts usually do not have expiration dates. For “warranty
claims of non-electrical parts”, please include a photocopy of the original NABCO invoice the part was
purchased on.
Date Returned – the date that the part is returned to NABCO Entrances Inc.
Requested Repair and Return Action – Specify in/out warranty for R&R, Exchange, or in warranty for
credit. For requests for credits, please write the number of the invoice you want credited.
Firm Name
Date of Installation
Installed at Job
Describe Part Problem
The RMT tag is printed in triplicate. Please keep the top copy of the tag for your returns. Send the remaining two
copies along with the part to the attention of the Repair and Return Department at NABCO Entrances Inc. Please
remember to package the parts properly. Ship the parts freight prepaid. Collect shipments will be refused. If
inquiring on the returned part, please use the RMT number associated with that part.
NABCO Entrances Standard Terms & Conditions and Warranty govern all returned items. These are provided in
detail in the Terms and Conditions section of the NABCO Entrances Price Book. If you have any questions on
warranty or the use of the RMT tags, please call NABCO’s Customer Service Department toll free at 1-877NABCO WI (1-877-622-2694).
30
NABCO
ENTRANCES INC.
P/N 14-10275
Z. Appendix
31
A1.
A2.
A3.
A4.
A5.
A6.
Full Open – Concrete Building Frame Pg. 1 of 6
Full Open – Concrete Building Frame Pg. 2 of 6
Full Open – Steel Building Frame Pg. 3 of 6
Full Open – Steel Building Frame Pg. 4 of 6
Full Open – Aluminum Building Frame Pg. 5 of 6
Full Open – Aluminum Building Frame Pg. 6 of 6
A7.
A8.
A9.
A10.
A11.
A12.
Fixed Sidelite – Concrete Building Frame Pg. 1 of 6
Fixed Sidelite – Concrete Building Frame Pg. 2 of 6
Fixed Sidelite – Steel Building Frame Pg. 3 of 6
Fixed Sidelite – Steel Building Frame Pg. 4 of 6
Fixed Sidelite – Aluminum Building Frame Pg. 5 of 6
Fixed Sidelite – Aluminum Building Frame Pg. 6 of 6
NABCO
ENTRANCES INC.
2" Typ
3" Typ
6" Typ
Bottom Rail
Top Rail
4" Typ
4" Typ
SX
3500 PSI
Concrete
3500 PSI
Concrete
3500 PSI
Concrete
Threshold
Header
Jambs
Design Pressure Rating
Substrate
EXTERIOR ELEVATION
SX
ACCESS COVER (INTERIOR) SIDE
"Y"
Header
3" Typ
Bottom Rail
35"
Top Rail
Location
SO
"X"
Bottom Rail
42 13/16"
Max D/O
70 1/2"
Max D/O
Top Rail
2" Typ
"Y"
SO
1"
(Typical)
1/2" Glass Bite
#10 x 2"
@ 12" o.c.
except near
corner @ 3"
o.c.
Glass Stop
Channel
142335
A1
Lock Reinforcement Plate
1 1/2" x 15" x .105" (12 Ga)
Door Sweep
Exterior
Mounting Screws
(Pairs)
3 1/4"
1 3/4"
Interior
R/H Carrier
6 1/2"
1/4"
Tie Rods
3/8" x
45 15/16"
Max
1/2"
REVISIONS
3 Updated Drawing
2 Updated Floor Track
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
29May01
07Feb.00
01JUL98
01APR97
DATE
Threshold
Tie Rods Torque Pressure
Is 15-20 Ft. Lbs.
Interior
1 3/4"
1 1/2"
Header
1/4" Max
Shim Space
DRAWING NUMBER:
1175-04C
Page 1 of 6
CONCRETE BUILDING FRAME CONSTRUCTION
STANDARD ELEVATIONS & SECTIONS
SYSTEM GT1175 BIPART SLIDER - FULL OPEN
Concrete Construction
2
Exterior
SECTION "X-X"
Threshold
Ramp
(Both Sides)
1/2"
6 1/2"
3 1/2"
L/H Carrier
Weathering Pile
(Schelegel
Polybond)
Cover
1/4" Max
Shim Space
S82 W18717 GEMINI DRIVE P.O. BOX 906 MUSKEGO, WISCONSIN 53150
TOLL FREE PHONE: 1-877-622-2694
FAX: (262) 679-2505
SECTION "Y-Y"
Mounting
Screws
Pairs
Sidelight Sweep
Dlubak Technologies
Laminated/Tempered
Glass (Typical)
Aluminum Angle
Glass Stop
Base
142336
#10 - 24 x PFH
Thread Forming
Staggered 2" From
Each End 4-6" O.C.
Adams Rite #1853A/505
Maximum Security Lock
Extending Into Header
and Threshold
(See Page 2)
Dow 995 Silicone
"Z"
12" Typ
4" Typ
4 Typ
6" Typ
6" Typ
6" Typ
6" Typ
3" Typ
Bottom Rail
Top Rail
4" Typ
2" Typ
WHERE WATER INFILTRATION WHERE WATER INFILTRATION
REQUIREMENT IS NEEDED
REQUIREMENT IS NOT NEEDED
Positive
NOT APPROVED
+60 PSF
Negative
NOT APPROVED
-70 PSF
4 Typ
9 3/4" Typ
12" Typ
91 1/2"
Max
"Z"
12" Typ
9 3/4" Typ
"X"
70 1/4" Max D/O
4" Typ
1"
6'-11" DOOR OPENING HEIGHT
3 1/2"
7 1/2"
7'-0"
Door Pivot
(See Page 2)
1 1/2"
7'-7 1/2" FRAME HEIGHT
Kawneer Flush Bolt
(Typical)
(See Page 2)
6 1/2"
70 1/2" Max D/O
All Anchors are in Pairs
192" Max
4"
4"
1 1/4"
4"
32
1"
Reference Fastener Chart for Anchors
P/N 14-10275
NABCO
ENTRANCES INC.
33
4'-0"
5'-0"
6'-0"
7'-0"
TYPE
2 1/8"
14 1/8" Typ
14 1/8" Typ
5/8" Typ Rod Engagement
3/16"
Panel
Stile
1.0"
3"
1.75" Typ
Pivot Rod
1.0" Dia.
2 1/8"
Pivot
Stile
3.5"
Top
Rail
A2
Typical Door Pivot
Pre-Load
Block
"B"
(DOOR OPENING)
"A"
2 1/8" 2 1/8"
(2) 1/4 - 20 x 1 3/4"
Hex Head Capscrew
Gr. 5
(2) 3/8 - 16 x 1 1/2"
Holocrome Low Head
Socket Capscrew
SECTION "Z-Z"
Carrier
2.06"
4.0"
Carrier Bar
Weldment
Door Stiles
Weathering Pile
(Amesbury - Center Fin)
Panel Stile
"D"
"E"
"C"
"D"
"E"
"G"
"F"
Panel
Stile
Jambs
REVISIONS
Updated Drawing
Updated Floor Track
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
3
2
29May01
07Feb.00
01JUL98
01APR97
DATE
Composition
Manufacturer
William L. Bonnell Co.
DRAWING NUMBER:
1175-04C
Page 2 of 6
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6005 - T5 aluminum
6005 - T5 aluminum
6061 - T6 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
FAX: (262) 679-2505
249009
249010
249011
149014
149088
149359
149085
149086
148922
149016
149017
145840
242497
142336
142335
NABCO Part No.
Material List
Use (7) 1/4" x 3 3/4" ITW Buildex PFH Tapcons in pairs at 12" o.c. starting
9 3/4" from each corner, total of (14) Tapcons
Header (Ext.)
Roller Track (Ext.)
Cover (Ext.)
Door Carrier (Ext.)
Top Rail - Sidelite (Ext.)
Top Rail - Door (Ext.)
Bottom Rail - All (Ext.)
Pivot Stile (Ext.)
Stile (Ext.)
Threshold (Ext.)
Floor Track Ramp (Ext.)
Angle (Ext.)
Jamb (Ext.)
Glass Stop Base (Ext.)
Glass Stop Channel (Ext.)
Description
3500 PSI
Concrete
use (4) 1/4" x 2 3/4" ITW Buildex PFH Tapcons with minimun 1 3/4" embedment
in 3500 psi concrete at each sash corner, a total of (28) in all at header
3500 PSI
Concrete
Header
Mounting
Screws
(Pairs)
in 3500 psi concrete at each sash corner, a total of (48) in all at threshold
3/16"
3500 PSI
Concrete
2 1/8"
Weathering
Pile
(Schelegel
Polybond)
1/4" Max
Shim Space
Threshold
Fastener Type, Spacing and Quantity
Fastener Chart
Panel Stile
Weathering
Strip
1 3/4"
Substrate
3"
2 1/8"
2 1/8"
Door Stile
Pivot Rod
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Location
Exterior
Interior
DIMENSION DIMENSION DIMENSION DIMENSION "D" DIMENSION DIMENSION DIMENSION "G" OPENING DIMENSION
"A"
"B"
"C"
(Door Panel Width)
"E"
"F"
Daylight Opening Incl. 1/4" shim each side
48"
54"
10'-0"
29 1/4"
23"
31 1/16"
24 13/16"
10' 1/2"
60"
66"
12'-0"
35 1/4"
29"
37 1/16"
30 13/16"
12' 1/2"
72"
78"
14'-0"
41 1/4"
35"
43 1/16"
36 13/16"
14' 1/2"
84"
90"
16'-0"
47 1/4"
41"
49 1/16"
42 13/16"
16' 1/2"
"G"
"F"
2 1/8"
Kawneer #37227
Door Stile
Pivot Rod
Weathering
Strip
Flush Bolt & Lock Rod Detail
35.0"
1/4" Max
Shim Space
3/4"
4 1/2" 3"
Mounting
Screws
(Pairs)
1 3/4"
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
P/N 14-10275
NABCO
ENTRANCES INC.
3" Typ
6" Typ
Bottom Rail
Top Rail
SX
3500 PSI
Concrete
Min. 1/8"
thick steel
Min. 1/8"
thick steel
Threshold
Header
Jambs
Substrate
EXTERIOR ELEVATION
SX
"Y"
Header
3" Typ
Bottom Rail
35"
Top Rail
Location
SO
"X"
Bottom Rail
42 13/16"
Max D/O
70 1/2"
Max D/O
Top Rail
6" Typ
6" Typ
4" Typ
6" Typ
SO
1"
(Typical)
1/2" Glass Bite
#10 x 2"
@ 12" o.c.
except near
corner @ 3"
o.c.
Glass Stop
Channel
142335
A3
1 1/2" x 15" x .105" (12 Ga)
Door Sweep
Exterior
Mounting Screws
(Pairs)
3 1/4"
1 3/4"
Interior
R/H Carrier
6 1/2"
1/4"
Tie Rods
3/8" x
45 15/16"
Max
1/2"
REVISIONS
3 Updated Drawing
2 Updated Floor Track
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
29May01
07Feb.00
01JUL98
01APR97
DATE
Threshold
Is 15-20 Ft. Lbs.
Interior
1 3/4"
1 1/2"
Header
1/4" Max
Shim Space
DRAWING NUMBER:
1175-04S
Page 3 of 6
STEEL BUILDING FRAME CONSTRUCTION
Steel Construction
2
Exterior
SECTION "X-X"
Threshold
Ramp
(Both Sides)
1/2"
6 1/2"
3 1/2"
L/H Carrier
Weathering Pile
(Schelegel
Polybond)
Cover
1/4" Max
Shim Space
FAX: (262) 679-2505
SECTION "Y-Y"
Mounting
Screws
Pairs
Sidelight Sweep
Dlubak Technologies
Laminated/Tempered
Glass (Typical)
Aluminum Angle
Glass Stop
Base
142336
#10 - 24 x PFH
Thread Forming
Staggered 2" From
Each End 4-6" O.C.
and Threshold
(See Page 2)
Dow 995 Silicone
"Z"
12" Typ
4" Typ
6" Typ
4 Typ
6" Typ
6" Typ
6" Typ
6" Typ
3" Typ
Bottom Rail
Top Rail
4"
Positive
NOT APPROVED
+60 PSF
Negative
NOT APPROVED
-70 PSF
4 Typ
9 3/4" Typ
12" Typ
91 1/2"
Max
"Z"
12" Typ
9 3/4" Typ
4" Typ
"Y"
70 1/4" Max D/O
"X"
3 1/2"
7 1/2"
7'-0"
4"
1 1/2"
1"
Door Pivot
(See Page 2)
192" Max
6 1/2"
70 1/2" Max D/O
Kawneer Flush Bolt
(Typical)
(See Page 2)
4"
4"
1 1/4"
4"
34
1"
P/N 14-10275
NABCO
ENTRANCES INC.
35
4'-0"
5'-0"
6'-0"
7'-0"
TYPE
2 1/8"
14 1/8" Typ
14 1/8" Typ
3/16"
Panel
Stile
1.0"
3"
1.75" Typ
Pivot Rod
1.0" Dia.
2 1/8"
Pivot
Stile
3.5"
Top
Rail
A4
Typical Door Pivot
Pre-Load
Block
"B"
(DOOR OPENING)
"A"
2 1/8" 2 1/8"
(2) 1/4 - 20 x 1 3/4"
Hex Head Capscrew
Gr. 5
(2) 3/8 - 16 x 1 1/2"
Holocrome Low Head
Socket Capscrew
SECTION "Z-Z"
Carrier
2.06"
4.0"
Carrier Bar
Weldment
Door Stiles
Weathering Pile
Panel Stile
"D"
"E"
"C"
"D"
"E"
Min. 1/8"
thick steel
Min. 1/8"
thick steel
Header
Jambs
2
29May01
07Feb.00
01JUL98
01APR97
DATE
"G"
"F"
Panel
Stile
Fastener Chart
Panel Stile
Weathering
Strip
Door Stile
Pivot Rod
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
2 1/8"
1 3/4"
3/16"
Mounting
Screws
(Pairs)
Weathering
Pile
(Schelegel
Polybond)
1/4" Max
Shim Space
Composition
Manufacturer
DRAWING NUMBER:
1175-04S
Page 4 of 6
Steel Construction
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6005 - T5 aluminum
6005 - T5 aluminum
6061 - T6 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
FAX: (262) 679-2505
249009
249010
249011
149014
149088
149359
149085
149086
148922
149016
149017
145840
242497
142336
142335
NABCO Part No.
Material List
Use (7) 1/4" x 3 1/4" Zinc Tek (Broward bolt) pairs at 12" o.c. starting 9 3/4"
from each corner, total of (14) anchors
use (4) 1/4 - 14 x 1 1/4" Hilti HWH self drilling screws with minimum 1" embedment
in steel at each sash corner, a total of (32) in all at header
2 1/8"
2 1/8"
Header (Ext.)
Roller Track (Ext.)
Cover (Ext.)
Door Carrier (Ext.)
Pivot Stile (Ext.)
Stile (Ext.)
Threshold (Ext.)
Angle (Ext.)
Jamb (Ext.)
REVISIONS
Updated Drawing
Updated Floor Track
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
3
3500 PSI
Concrete
Description
Substrate
Location
3"
Threshold
Exterior
Interior
"A"
"B"
"C"
(Door Panel Width)
"E"
"F"
48"
54"
10'-0"
29 1/4"
23"
31 1/16"
24 13/16"
10' 1/2"
60"
66"
12'-0"
35 1/4"
29"
37 1/16"
30 13/16"
12' 1/2"
72"
78"
14'-0"
41 1/4"
35"
43 1/16"
36 13/16"
14' 1/2"
84"
90"
16'-0"
47 1/4"
41"
49 1/16"
42 13/16"
16' 1/2"
"G"
"F"
2 1/8"
Kawneer #37227
Door Stile
Pivot Rod
Weathering
Strip
35.0"
1/4" Max
Shim Space
3/4"
4 1/2" 3"
Mounting
Screws
(Pairs)
1 3/4"
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
P/N 14-10275
NABCO
ENTRANCES INC.
Positive
Negative
3" Typ
6" Typ
Bottom Rail
Top Rail
SX
Min 1/8" thick
6063-T5 Aluminum
Min 1/8" thick
6063-T5 Aluminum
Header
Jamb
Substrate
3500 PSI
Concrete
Location
EXTERIOR ELEVATION
SX
"Y"
Header
3" Typ
Bottom Rail
35"
Top Rail
6" Typ
4" Typ
6" Typ
Threshold
SO
"X"
Bottom Rail
42 13/16"
Max D/O
70 1/2"
Max D/O
Top Rail
"Y"
SO
1"
(Typical)
1/2" Glass Bite
#10 x 2"
@ 12" o.c.
except near
corner @ 3"
o.c.
Glass Stop
Channel
142335
A5
1 1/2" x 15" x .105" (12 Ga)
Door Sweep
Exterior
Mounting Screws
(Pairs)
2
REVISIONS
Updated Drawing
Updated Floor Track
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
3
3 1/4"
1 3/4"
Interior
R/H Carrier
6 1/2"
1/4"
Tie Rods
3/8" x
45 15/16"
Max
1/2"
29May01
07Feb.00
01JUL98
01APR97
DATE
Threshold
Is 15-20 Ft. Lbs.
Interior
1 3/4"
1 1/2"
Header
1/4" Max
Shim Space
DRAWING NUMBER:
1175-04A
Page 5 of 6
ALUMINUM BUILDING FRAME CONSTRUCTION
Aluminum Construction
2
Exterior
SECTION "X-X"
Threshold
Ramp
(Both Sides)
1/2"
6 1/2"
3 1/2"
L/H Carrier
Weathering Pile
(Schelegel
Polybond)
Cover
1/4" Max
Shim Space
FAX: (262) 679-2505
SECTION "Y-Y"
Mounting
Screws
Pairs
Sidelight Sweep
Dlubak Technologies
Laminated/Tempered
Glass (Typical)
Aluminum Angle
Glass Stop
Base
142336
#10 - 24 x PFH
Thread Forming
Staggered 2" From
Each End 4-6" O.C.
and Threshold
(See Page 2)
Dow 995 Silicone
"Z"
12" Typ
4" Typ
6" Typ
4 Typ
6" Typ
6" Typ
6" Typ
6" Typ
3" Typ
Bottom Rail
Top Rail
4" Typ
6" Typ
+60 PSF
NOT APPROVED
-70 PSF
NOT APPROVED
4 Typ
9 3/4" Typ
12" Typ
91 1/2"
Max
"Z"
12" Typ
9 3/4" Typ
4" Typ
"X"
70 1/4" Max D/O
Door Pivot
(See Page 2)
3 1/2"
1"
4" Typ
1 1/2"
7 1/2"
7'-0"
Kawneer Flush Bolt
(Typical)
(See Page 2)
6 1/2"
70 1/2" Max D/O
192" Max
4"
4"
1 1/4"
4"
36
1"
P/N 14-10275
NABCO
ENTRANCES INC.
37
4'-0"
5'-0"
6'-0"
7'-0"
TYPE
2 1/8"
14 1/8" Typ
14 1/8" Typ
3/16"
Panel
Stile
1.0"
3"
1.75" Typ
Pivot Rod
1.0" Dia.
2 1/8"
Pivot
Stile
3.5"
Top
Rail
A6
Typical Door Pivot
Pre-Load
Block
"B"
(DOOR OPENING)
"A"
2 1/8" 2 1/8"
(2) 1/4 - 20 x 1 3/4"
Hex Head Capscrew
Gr. 5
(2) 3/8 - 16 x 1 1/2"
Holocrome Low Head
Socket Capscrew
SECTION "Z-Z"
Carrier
2.06"
4.0"
Carrier Bar
Weldment
Door Stiles
Weathering Pile
Panel Stile
"D"
"E"
"C"
"D"
"E"
"G"
"F"
Jamb
REVISIONS
Updated Drawing
Updated Floor Track
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
3
2
29May01
07Feb.00
01JUL98
01APR97
DATE
Composition
Manufacturer
DRAWING NUMBER:
1175-04A
Page 6 of 6
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6005 - T5 aluminum
6005 - T5 aluminum
6061 - T6 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
FAX: (262) 679-2505
249009
249010
249011
149014
149088
149359
149085
149086
148922
149016
149017
145840
242497
142336
142335
NABCO Part No.
Material List
Use (7) 1/4" x 3 1/4" Zinc Tek (Broward bolt) pairs at 12" o.c. starting 9 3/4"
from each corner, total of (14) anchors
Header (Ext.)
Roller Track (Ext.)
Cover (Ext.)
Door Carrier (Ext.)
Pivot Stile (Ext.)
Stile (Ext.)
Threshold (Ext.)
Angle (Ext.)
Jamb (Ext.)
Description
Min 1/8" thick
6063-T5 Aluminum
use (4) 1/4" - 14 x 1 1/4" Hilti HWH self drilling screws with minimum 1"
embedment in Aluminum at each sash corner, a total of (32) in all at header
Min 1/8" thick
6063-T5 Aluminum
Mounting
Screws
(Pairs)
Header
3/16"
use (6) 1/4" x 2 3/4" ITW Buildex PFH Tapcons with minimun 1 3/4"embedment
2 1/8"
Weathering
Pile
(Schelegel
Polybond)
1/4" Max
Shim Space
3500 PSI
Concrete
Fastener Chart
Panel Stile
1 3/4"
Threshold
2 1/8"
Weathering
Strip
Panel
Stile
Substrate
3"
2 1/8"
Door Stile
Pivot Rod
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Location
Exterior
Interior
"A"
"B"
"C"
(Door Panel Width)
"E"
"F"
48"
54"
10'-0"
29 1/4"
23"
31 1/16"
24 13/16"
10' 1/2"
60"
66"
12'-0"
35 1/4"
29"
37 1/16"
30 13/16"
12' 1/2"
72"
78"
14'-0"
41 1/4"
35"
43 1/16"
36 13/16"
14' 1/2"
84"
90"
16'-0"
47 1/4"
41"
49 1/16"
42 13/16"
16' 1/2"
"G"
"F"
2 1/8"
Kawneer #37227
Door Stile
Pivot Rod
Weathering
Strip
35.0"
1/4" Max
Shim Space
3/4"
4 1/2" 3"
Mounting
Screws
(Pairs)
1 3/4"
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
P/N 14-10275
NABCO
ENTRANCES INC.
4" Typ
Bottom Rail
43 1/8"
Max D/O
"O"
3500 PSI
Concrete
3500 PSI
Concrete
3500 PSI
Concrete
Threshold
Header
Jambs
2" Typ
SX
2" Typ
4" Typ
4" Typ
Bottom Rail
"SX"
Top Rail
6" Typ
4" Typ
6" Typ
4" Typ
.77"
.69" Typ
1.1" Typ
.88"
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
Positive
NOT APPROVED
+60 PSF
Negative
NOT APPROVED
-60 PSF
O
"Y" "X"
2" Typ
4" Typ
Bottom Rail
"O"
Top Rail
Bottom
Rail
4" Typ
Detail "B"
1.12" Typ
1/2" Typ
Stile
Detail "D"
Detail "B"
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Detail "C"
Stile
Jamb
Tube
3 1/4"
1 3/4"
Exterior
R/H Carrier
6 1/2"
3 1/2"
1/4"
1/2"
Tie Rods
3/8" x
46 1/8"
Max
29MAY01
01JUL98
01APR97
DATE
FAX: (262) 679-2505
SECTION "Y-Y"
Mounting
Screw
Pairs
Threshold
Interior
REVISIONS
Updated
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
2
Threshold
Ramp
(Both Sides)
3 7/16"
.72 Typ
Detail "A"
Stile
Top Rail
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
Header
.63"
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Top Rail
A7
.72 Typ
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
4 1/8"
Jamb
Tube
.66"
1 1/2" x 15" x .105" (12 Ga)
.72" Typ
.59"
1/4" Max
Shim Space
Dlubak Technologies
Laminated/Tempered
Glass (Typical)
Aluminum Angle Mounting Screws
(Pairs)
Glass Stop
Base
142336
#10 - 24 x PFH
Thread Forming
Staggered 2" From
Each End 4-6" O.C.
Dow 995 Silicone
(Typical)
1/2" Glass Bite
Detail "C"
1"
Sidelite Attached to
Header, Threshold
and Jamb with (4)
10 Gauge Steel
Angle Brackets
"Z"
12" Typ
4" Typ
6" Typ
9 3/4" Typ
1.0" Typ
Detail "A"
4" Typ
6" Typ
"Y" "X"
Bottom
Rail
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Detail "D"
Stile
EXTERIOR ELEVATION
ACCESS COVER (EXTERIOR) SIDE
SX
Substrate
Location
O
Header
Bottom Rail
35"
"SX"
Top Rail
Kawneer Flush Bolt
(Typical)
(See Sheet 2)
70 1/2"
Max D/O
Top Rail
4" Typ
and Threshold
(See Sheet 2)
9 3/4"
12" Typ
91 1/2"
Max
"Z"
12" Typ
9 3/4" Typ
Door Pivot
(See Page 2)
1 1/2"
70 1/4" MAX D/O
7 1/2"
1 3/4"
1 1/2"
Header
1/4" Max
Shim Space
Interior
SECTION "X-X"
Door Sweep
Is 15-20 Ft. Lbs.
Exterior
Weathering Pile
(Schelegel
Polybond)
Cover
L/H Carrier
6 1/2"
3 1/2"
DRAWING NUMBER:
1175-02C
Page 1 of 6
SYSTEM GT1175 BIPART SLIDER - FIXED SIDELITE
7'-0"
#10 x 2"
@ 12" o.c.
except near
corner @ 3"
o.c.
Glass Stop
Channel
142335
1"
192" Max
4"
4"
1 1/4"
6 1/2"
70 1/2" MAX D/O
38
5"
P/N 14-10275
NABCO
ENTRANCES INC.
39
3/4"
3"
1 3/4"
2"
14 1/8" Typ
Panel
Stile
Kawneer #37227
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Door Stile
Pivot Rod
Weathering
Strip
TYPE DIMENSION DIMENSION DIMENSION DIMENSION "D"
"A"
"B"
"C"
(Door Panel Width)
4'-0"
48"
54"
10'-0"
29 1/4"
5'-0"
60"
66"
12'-0"
35 1/4"
6'-0"
72"
78"
14'-0"
41 1/4"
7'-0"
84"
90"
16'-0"
47 1/4"
35.0"
14 1/8" Typ
1/4" Max
Shim Space
4 1/2"
Mounting
Screws
(Pairs)
"F"
"G"
Door Stiles
"C"
2 1/8" 2 1/8"
"A"
"B"
DIMENSION
"E"
23"
29"
35"
41"
249009
249010
249011
149014
149088
149359
149085
149087
149086
148922
149501
149016
149017
145840
242497
142336
142335
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6005 - T5 aluminum
6005 - T5 aluminum
6061 - T6 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
Composition
0
1
Updated Drawing
REVISED
INITIAL ISSUE
REV DESCRIPTION
2
REVISIONS
DIMENSION DIMENSION "G"
Opening Dimension
"F"
Daylight Opening (Incl. 1/4" shim each side)
31 1/4"
25 1/8"
10' 1/2"
37 1/4"
31 1/8"
12' 1/2"
43 1/4"
37 1/8"
14' 1/2"
49 1/4"
43 1/8"
16' 1/2"
Header (Ext.)
Roller Track (Ext.)
Cover (Ext.)
Door Carrier (Ext.)
Bottom Rail - Door (Ext.)
Bottom Rail - Sidelite (Ext.)
Pivot Stile (Ext.)
Stile (Ext.)
Fixed Vert. Mullion (Ext.)
Threshold (Ext.)
Angle (Ext.)
Jamb (Ext.)
NABCO Part No.
Manufacturer
Use (7) 1/4" x 3 3/4" ITW Buildex PFH Tapcons in pairs at 12" o.c. starting 9 3/4"
from each corner, a total of (14) anchors
3500 PSI
Concrete
Jamb
Material List
Use (4) 1/4" x 2 3/4" ITW Buildex PFH Tapcons with minimun 1 3/4"embedment
in 3500 psi concrete at each sash corner for intermediate sashes, (4) at corner of
jamb and header, a total of (32) in all at header
Description
2 1/8"
2 1/8"
29May01
01JUL98
01APR97
DATE
Weathering Pile
Use (4) 1/4" x 2 3/4" ITW Buildex PFH Tapcons with minimun 1 3/4"embedment
in 3500 psi concrete at each sash corner, (2) at corner of jamb and threshold, a
total of (28) in all with full threshold
"E"
"D"
3500 PSI
Concrete
3500 PSI
Concrete
Threshold
Fastener Chart
Exterior
Interior
3"
Header
Substrate
SECTION "Z-Z"
"E"
"D"
Panel Stile
Location
2 1/8"
2 1/8"
3"
Pivot
Stile
3.5"
Top
Rail
Mounting
Screws
(Pairs)
1/4" Max
Shim Space
DRAWING NUMBER:
1175-02C
Page 2 of 6
(2) 1/4 - 20 x 1 3/4"
Hex Head Capscrew
Gr. 5
(2) 3/8 - 16 x 1 1/2"
Holocrome Low Head
Socket Capscrew
1 3/4"
A8
Typical Door Pivot
Pre-Load
Block
Carrier Bar
Weldment
2"
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Panel
Stile
Carrier
2.06"
4.0"
FAX: (262) 679-2505
1.75" Typ
Pivot Rod
1.0" Dia.
1.0"
Door Stile
Pivot Rod
Weathering
Strip
Panel Stile
"F"
"G"
P/N 14-10275
NABCO
ENTRANCES INC.
4" Typ
Bottom Rail
43 1/8"
Max D/O
"O"
70 1/2"
Max D/O
Top Rail
4" Typ
Header
Bottom Rail
35"
"SX"
Top Rail
2" Typ
Min. 1/8"
thick steel
Min. 1/8"
thick steel
Header
Jambs
Positive
Negative
3500 PSI
Concrete
Threshold
4" Typ
SX
2" Typ
4" Typ
4" Typ
Bottom Rail
"SX"
Top Rail
4" Typ
.77"
.69" Typ
1.1" Typ
.88"
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
NOT APPROVED
+60 PSF
-60 PSF
NOT APPROVED
O
"Y" "X"
2" Typ
4" Typ
Bottom Rail
"O"
Top Rail
4" Typ
Detail "B"
1.12" Typ
1/2" Typ
Stile
Detail "D"
Detail "B"
Detail "C"
Stile
Jamb
Tube
3 7/16"
.72 Typ
1
1 1/2"
3 1/4"
1 3/4"
Exterior
R/H Carrier
6 1/2"
3 1/2"
1/4"
1/2"
Tie Rods
3/8" x
46 1/8"
Max
29MAY01
01JUL98
01APR97
DATE
FAX: (262) 679-2505
SECTION "Y-Y"
Mounting
Screw
Pairs
Threshold
Interior
REVISIONS
Updated
REVISED
0 INITIAL ISSUE
REV DESCRIPTION
2
Threshold
Ramp
(Both Sides)
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
Top Rail
Detail "A"
Stile
Header
.63"
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Top Rail
A9
.72 Typ
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
4 1/8"
Jamb
Tube
.66"
1 1/2" x 15" x .105" (12 Ga)
.72" Typ
.59"
Dow 995 Silicone
(Typical)
1/2" Glass Bite
Detail "C"
1"
Header, Threshold
and Jamb with (4)
10 Gauge Steel
Angle Brackets
"Z"
12" Typ
9 3/4" Typ
4" Typ
Bottom
Rail
1.0" Typ
Detail "A"
4" Typ
2" Typ
"Y" "X"
Bottom
Rail
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Detail "D"
Stile
EXTERIOR ELEVATION
SX
Substrate
Location
O
2" Typ
and Threshold
(See Sheet 2)
Kawneer Flush Bolt
(Typical)
(See Sheet 2)
9 3/4"
12" Typ
91 1/2"
Max
"Z"
12" Typ
9 3/4" Typ
2" Typ
1/4" Max
Shim Space
Dlubak Technologies
Laminated/Tempered
Glass (Typical)
(Pairs)
Glass Stop
Base
142336
#10 - 24 x PFH
Thread Forming
Staggered 2" From
Each End 4-6" O.C.
70 1/4" MAX D/O
#10 x 2"
@ 12" o.c.
except near
corner @ 3"
o.c.
Glass Stop
Channel
142335
1"
192" Max
7 1/2"
1 3/4"
1 1/2"
Steel Construction
Header
1/4" Max
Shim Space
SECTION "X-X"
Door Sweep
Is 15-20 Ft. Lbs.
Exterior
Weathering Pile
(Schelegel
Polybond)
Cover
L/H Carrier
6 1/2"
3 1/2"
Interior
DRAWING NUMBER:
1175-02S
Page 3 of 6
7'-0"
4"
4"
1 1/4"
6 1/2"
70 1/2" MAX D/O
40
5"
Door Pivot
(See Page 2)
P/N 14-10275
NABCO
ENTRANCES INC.
41
3/4"
3"
1 3/4"
2"
14 1/8" Typ
Panel
Stile
Kawneer #37227
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Door Stile
Pivot Rod
Weathering
Strip
"A"
"B"
"C"
(Door Panel Width)
4'-0"
48"
54"
10'-0"
29 1/4"
5'-0"
60"
66"
12'-0"
35 1/4"
6'-0"
72"
78"
14'-0"
41 1/4"
7'-0"
84"
90"
16'-0"
47 1/4"
35.0"
14 1/8" Typ
1/4" Max
Shim Space
4 1/2"
Mounting
Screws
(Pairs)
"F"
"G"
Door Stiles
"C"
2 1/8" 2 1/8"
"A"
DIMENSION
"E"
23"
29"
35"
41"
Composition
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6005 - T5 aluminum
6005 - T5 aluminum
6061 - T6 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
REVISIONS
Updated Drawing
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
2
Opening Dimension
"F"
31 1/4"
25 1/8"
10' 1/2"
37 1/4"
31 1/8"
12' 1/2"
43 1/4"
37 1/8"
14' 1/2"
49 1/4"
43 1/8"
16' 1/2"
249009
249010
249011
149014
149088
149359
149085
149087
149086
148922
149501
149016
149017
145840
242497
142336
142335
NABCO Part No.
Header (Ext.)
Roller Track (Ext.)
Cover (Ext.)
Door Carrier (Ext.)
Pivot Stile (Ext.)
Stile (Ext.)
Threshold (Ext.)
Angle (Ext.)
Jamb (Ext.)
29May01
01JUL98
01APR97
DATE
Use (7) 1/4" - 14 x 3 1/4" Hilti HWH self drilling screws with minimum 1" embedment
in Steel in pairs at 12" o.c. starting 9 3/4" from each corner, total of (14) anchors
Min 1/8" thick
Steel
Jamb
Manufacturer
in Steel at each sash corner for intermediate sashes, (2) at corner of jamb and header,
a total of (28) in all at header
Min 1/8" thick
Steel
Header
Description
Use (4) 1/4" x 2 3/4" ITW Buildex PFH Tapcons with minimun 1 3/4" embedment
3500 PSI
Concrete
Material List
2 1/8"
2 1/8"
Weathering Pile
Threshold
"E"
"D"
3"
Exterior
Interior
Substrate
Fastener Chart
SECTION "Z-Z"
"E"
"D"
Panel Stile
"B"
Location
2 1/8"
2 1/8"
3"
Pivot
Stile
3.5"
Top
Rail
Mounting
Screws
(Pairs)
1/4" Max
Shim Space
(2) 1/4 - 20 x 1 3/4"
Hex Head Capscrew
Gr. 5
(2) 3/8 - 16 x 1 1/2"
Holocrome Low Head
Socket Capscrew
1 3/4"
DRAWING NUMBER:
1175-02S
Page 4 of 6
Steel Construction
A10
Typical Door Pivot
Pre-Load
Block
Carrier Bar
Weldment
2"
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Panel
Stile
Carrier
2.06"
4.0"
FAX: (262) 679-2505
1.75" Typ
Pivot Rod
1.0" Dia.
1.0"
Door Stile
Pivot Rod
Weathering
Strip
Panel Stile
"F"
"G"
P/N 14-10275
NABCO
ENTRANCES INC.
4" Typ
Bottom Rail
43 1/8"
Max D/O
"O"
2" Typ
SX
2" Typ
SX
2" Typ
4" Typ
4" Typ
Bottom Rail
"SX"
Top Rail
4" Typ
4" Typ
3500 PSI
Concrete
Min 1/8" thick
6063-T5 Aluminum
Min 1/8" thick
6063-T5 Aluminum
Threshold
Header
Jamb
.77"
.69" Typ
1.1" Typ
.88"
Bottom
Rail
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
Detail "D"
Stile
O
"Y" "X"
2" Typ
4" Typ
Bottom Rail
"O"
Top Rail
4" Typ
Detail "B"
1.12" Typ
1/2" Typ
Stile
Detail "D"
Detail "B"
.66"
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Stile
Detail "C"
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Top Rail
A11
.72 Typ
4 1/8"
Jamb
Tube
1/4 - 20 x 3/4"
Ph. Hd. Machine
Screw Plt'd Steel
Top Rail
1/4 - 20 x 7/16"
Ph. Hd. Machine
Screw Plt'd Steel
2
3 1/4"
1 3/4"
Exterior
R/H Carrier
6 1/2"
3 1/2"
1/4"
1/2"
Tie Rods
3/8" x
46 1/8"
Max
29MAY01
01JUL98
01APR97
DATE
FAX: (262) 679-2505
SECTION "Y-Y"
Mounting
Screw
Pairs
Threshold
Interior
REVISIONS
Updated
1 REVISED
0 INITIAL ISSUE
REV DESCRIPTION
Threshold
Ramp
(Both Sides)
Jamb
Tube
3 7/16"
.72 Typ
Detail "A"
Stile
1 1/2" x 15" x .105" (12 Ga)
.72" Typ
.59"
Header
.63"
1/4" Max
Shim Space
Dlubak Technologies
Laminated/Tempered
Glass (Typical)
(Pairs)
Glass Stop
Base
142336
#10 - 24 x PFH
Thread Forming
Staggered 2" From
Each End 4-6" O.C.
Dow 995 Silicone
(Typical)
1/2" Glass Bite
Detail "C"
1"
Header, Threshold
and Jamb with (4)
10 Gauge Steel
Angle Brackets
"Z"
12" Typ
9 3/4" Typ
4" Typ
Bottom
Rail
1.0" Typ
Detail "A"
4" Typ
2" Typ
"Y" "X"
Positive
NOT APPROVED
+60 PSF
Negative
NOT APPROVED
-60 PSF
Substrate
EXTERIOR ELEVATION
Location
O
Header
Bottom Rail
35"
"SX"
Top Rail
2" Typ
Kawneer Flush Bolt
(Typical)
(See Sheet 2)
70 1/2"
Max D/O
Top Rail
and Threshold
(See Sheet 2)
9 3/4"
12" Typ
91 1/2"
Max
"Z"
12" Typ
4" Typ
9 3/4" Typ
Door Pivot
(See Page 2)
1 1/2"
70 1/4" MAX D/O
1"
#10 x 2"
@ 12" o.c.
except near
corner @ 3"
o.c.
Glass Stop
Channel
142335
7 1/2"
1 3/4"
1 1/2"
Header
1/4" Max
Shim Space
SECTION "X-X"
Door Sweep
Is 15-20 Ft. Lbs.
Exterior
Weathering Pile
(Schelegel
Polybond)
Cover
L/H Carrier
6 1/2"
3 1/2"
Interior
DRAWING NUMBER:
1175-02A
Page 5 of 6
7'-0"
192" Max
4"
4"
1 1/4"
6 1/2"
70 1/2" MAX D/O
42
5"
P/N 14-10275
NABCO
ENTRANCES INC.
43
3/4"
3"
1 3/4"
2"
14 1/8" Typ
Panel
Stile
Kawneer #37227
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Door Stile
Pivot Rod
Weathering
Strip
"A"
"B"
"C"
(Door Panel Width)
4'-0"
48"
54"
10'-0"
29 1/4"
5'-0"
60"
66"
12'-0"
35 1/4"
6'-0"
72"
78"
14'-0"
41 1/4"
7'-0"
84"
90"
16'-0"
47 1/4"
35.0"
14 1/8" Typ
1/4" Max
Shim Space
4 1/2"
Mounting
Screws
(Pairs)
"F"
"G"
Door Stiles
"C"
2 1/8" 2 1/8"
"B"
"A"
DIMENSION
"E"
23"
29"
35"
41"
Composition
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6063 - T6 aluminum
6005 - T5 aluminum
6005 - T5 aluminum
6061 - T6 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
6063 - T5 aluminum
0
1
Updated Drawing
REVISED
INITIAL ISSUE
REV DESCRIPTION
2
REVISIONS
Opening Dimension
"F"
31 1/4"
25 1/8"
10' 1/2"
37 1/4"
31 1/8"
12' 1/2"
43 1/4"
37 1/8"
14' 1/2"
49 1/4"
43 1/8"
16' 1/2"
249009
249010
249011
149014
149088
149359
149085
149087
149086
148922
149501
149016
149017
145840
242497
142336
142335
NABCO Part No.
Header (Ext.)
Roller Track (Ext.)
Cover (Ext.)
Door Carrier (Ext.)
Pivot Stile (Ext.)
Stile (Ext.)
Threshold (Ext.)
Angle (Ext.)
Jamb (Ext.)
Manufacturer
29May01
01JUL98
01APR97
DATE
in Aluminum pairs at 12" o.c. starting 9 3/4" from each corner, total of (14) anchors
Min 1/8" thick
6063-T5 Aluminum
Jamb
Description
in Aluminum at each sash corner for intermediate sashes, (2) at corner of jamb and
header, a total of (28) in all at header
Material List
2 1/8"
2 1/8"
Weathering Pile
Use (4) 1/4" x 2 3/4" ITW Buildex PFH Tapcons with minimun 1 3/4" embedment
"E"
"D"
Min 1/8" thick
6063-T5 Aluminum
3500 PSI
Concrete
Threshold
Fastener Chart
Exterior
Interior
3"
Header
Substrate
SECTION "Z-Z"
"E"
"D"
Panel Stile
Location
2 1/8"
2 1/8"
3"
Pivot
Stile
3.5"
Top
Rail
1 3/4"
Mounting
Screws
(Pairs)
1/4" Max
Shim Space
(2) 1/4 - 20 x 1 3/4"
Hex Head Capscrew
Gr. 5
(2) 3/8 - 16 x 1 1/2"
Holocrome Low Head
Socket Capscrew
DRAWING NUMBER:
1175-02A
Page 6 of 6
A12
Typical Door Pivot
Pre-Load
Block
Carrier Bar
Weldment
2"
Jamb Tube
4 1/2" x 1 3/4" x 1/8"
Panel
Stile
Carrier
2.06"
4.0"
FAX: (262) 679-2505
1.75" Typ
Pivot Rod
1.0" Dia.
1.0"
Door Stile
Pivot Rod
Weathering
Strip
Panel Stile
"F"
"G"
P/N 14-10275
NABCO
ENTRANCES INC.

Model 1175 Hurricane Sliding Door System

Transcription

Similar documents

Price List - West Branch Rental