2886 General Directions e

Transcription

2886 General Directions e
English/Spanish 3
1/4
5
6
The Pattern
SYMBOLS
GRAIN LINE Place on
straight grain of fabric
parallel to selvage
2
9
13
PLACE SOLID LINE on
fold of fabric.
11
D
10
7
4
CENTER FRONT OR
BACK of garment.
14
NOTCHES
DOTS
17
C
pattern printed
side up
★
✻
See
SPECIAL
CUTTING
NOTES
USE PIECES 1 2 3
1C 44" 45" (115CM)
WITHOUT NAP
ALL SIZES
★
Clip inner
curves
BORDERED
EDGES
SELS.
5
USE PIECE 2
1
7
4
BORDERED EDGES
SELVAGES
Notch outer
curves
WITH NAP
ALL SIZES
SELVAGES
3
5
1
10
6
8
4
7
1D 20" TO 25" (51CM TO 64CM) FUSIBLE
ALL SIZES
BORDERED
EDGES
4
USE LAS PIEZAS 1 2 3 4 5 6 7
9
1B
SELVAGE
5
4
12
10
1D 20" A 25" (51CM A 64CM) ADHESIVA
TODAS LAS TALLAS
FOLD
SELVAGE
SELVAGES
WITH NAP
ALL SIZES
B DRESS
USE PIECES 4 5 6 7 8 9 10 11 12 13
B VESTIDO
8
USE LAS PIEZAS 4 5 6 7 8 9 10 11 12 13
10
6
8
5
12
SEL.
SELVAGE
SELVAGES
5
10
6
9
12
8
7
FOLD
11
13
7
USE PIECES 9 11 13 15 16
SELVAGE
4
FOLD
CONTRAST
SEL.
3C 44" 45" (115CM)
★
WITH NAP
ALL SIZES
11
9
SEL.
15 16
BORDERED EDGES
© Copyright 2008—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
LA PIEZA 14 SE CORTA EN EL ELASTICO
2A
4
FOLD
CUTTING LAYOUTS CONTINUED ON PAGE 2
44" 45" (115CM) CON PELUSA/ TODAS LAS TALLAS
2B 58" 60" (150CM) CON PELUSA/ TODAS LAS TALLAS
✻
WITH NAP
ALL SIZES
123
1C 44" 45" (115CM) SIN PELUSA/ TODAS LAS TALLAS
ENTRETELA USE LA PIEZA 2
7
8
58" 60" (150CM) CON PELUSA/ TODAS LAS TALLAS
FORRO USE LAS PIEZAS
SELVAGES
6
2A 44" 45" (115CM)
1
7
A VESTIDO- CORTADA A LO ANCHO
DE LA TELA CON RIBETE ESTAMPADO
12
SELS.
3B 58" 60" (150CM)
SELVAGE
A,B,C: DETERMINE EL LARGO ACABADO ANTES DE CORTAR
NOTA: PARA LAS TELAS CON RIBETE ESTAMPADO: SIGA EL DIAGRAMA DE
CORTE, MUEVA LAS PIEZAS ARRIBA O ABAJO SEGUN LA POSICION
DESEADA DEL RIBETE EN LA PRENDA DEJANDO EL MARGEN DE COSTURA
NECESSARIO
13 13
WITH NAP
ALL SIZES
2
SELVAGES
1A 44" 45" (115CM) CON PELUSA/ TODAS LAS TALLAS
USE PIECES 4 5 6 7 8 10 12
PIECE 14 IS CUT OF ELASTIC
3A 44" 45" (115CM)
b.
SELVAGE
Español
9
FOLD
SELS.
a.
SELVAGES
DOUBLE THICKNESS
2
CROSSWISE FOLD
CROSSWISE FOLD
3
5
6
Turn one fabric
layer around so
arrows on both
layers go in the
same direction.
Place RIGHT sides
together (b).
PIECE 14 IS CUT OF ELASTIC
CROSSWISE FOLD
WITH NAP
ALL SIZES
selvages indicating
direction of nap or
design. Fold fabric
crosswise with
RIGHT sides
together, and cut
along fold (a).
Open out
fabric to single
thickness. Cut
extending
piece on
RIGHT side of
fabric in
position
shown.
FOLD
1B 58" 60" (150CM)
Mark small
✻
arrows along both
If layout
shows a piece
extending past
fold, cut out all
pieces except
piece that
extends.
2B 58" 60" (150CM)
2
INTERFACING
CROSSWISE
FOLD
CROSSWISE FOLD
CROSSWISE FOLD
2
SPECIAL CUTTING NOTES
C DRESS
CROSSWISE FOLD
6
• FOR PILE, SHADED OR ONE WAY
DESIGN FABRICS: Use “with nap”
layouts
When lengthen or shorten lines are
not given, make adjustments at
lower edge of pattern.
SELS.
A DRESS- CUT CROSSWISE OF BORDER
SELS.
SELVAGES
PRINTED FABRIC
WITH NAP
ALL SIZES
• Pin mark dots.
11
SELS.
NOTE: FOR BORDER PRINTED FABRICS: FOLLOW CUTTING LAYOUT,
MOVE PIECES UP OR DOWN TO DESIRED POSITION OF BORDER ON
GARMENT AND ALLOW FOR CORRECT HEM ALLOWANCE.
1A 44" 45" (115CM)
Trim corners
• Snip edge of fabric to mark
notches, ends of fold lines and
center lines.
• FOR SINGLE THICKNESS: Place
fabric RIGHT side up.
SELVAGE
A,B,C: DETERMINE FINISHED LENGTH BEFORE CUTTING
3
• FOR DOUBLE THICKNESS: Fold
fabric with RIGHT sides together.
SEW garment following Sewing Directions.
PIN or machine-baste seams matching notches.
STITCH 5/8" (1.5 cm) seams unless otherwise stated.
PRESS seams open unless otherwise indicated clipping when necessary so
seams will lie flat.
• TRIM seams to reduce bulk, as shown below.
LINING
POSITION OF PATTERN PIECES MAY VARY SLIGHTLY ACCORDING
TO YOUR PATTERN SIZE
USE PIECES 1 2 3 4 5 6 7
To Quick Mark:
PIN pattern to fabric as shown in Cutting
Layouts.
•
•
•
•
Trim enclosed
seams into layers
AFTER CUTTING:
Transfer markings to WRONG side
of fabric before removing pattern.
Use pin and chalk method or
dressmaker’s tracing paper and
wheel.
CIRCLE your cutting layout.
Sewing
CROSSWISE FOLD
Cutting
Layouts
pattern printed
side down
SEAM ALLOWANCE: 5/8" (1.5cm)
unless otherwise stated is included but
not printed on MULTI-SIZE PATTERNS.
Mark your size with colored felt tip pen.
See chart on tissue for how to use MULTISIZE PATTERNS.
BEFORE CUTTING:
PRESS pattern pieces with a warm dry
iron. PRE-SHRINK fabric by pre-washing
washables or steam-pressing nonwashables.
TO SHORTEN:
At lengthen or
shorten lines,
make an even
pleat taking up
amount needed.
Tape in place.
LENGTHEN OR
SHORTEN LINES
1-BODICE FRONT -A
2-MIDRIFF FRONT -A /
MIDRIFF FRONT LINING -A,B,C
3-BODICE BACK -A
4-SKIRT FRONT -A,B,C
5-YOKE FRONT AND POCKET -A,B,C
6-POCKET FACING -A,B,C
7-SKIRT BACK -A,B,C
8-BODICE FRONT -B,C
9-BODICE FRONT BAND -B,C
10-SHOULDER STRAP -B,C
11-MIDRIFF FRONT -B,C
12-BODICE BACK -B,C
13-TIE END -B,C
14-BACK ELASTIC GUIDE -B,C
15-SKIRT FRONT BAND -C
16-SKIRT BACK BAND -C
17-FRONT -D
18-BACK -D
B
A
ADJUST IF NEEDED
Make adjustments before placing
pattern on fabric.
TO LENGTHEN:
Cut pattern
between
lengthen or
shorten lines.
Spread pattern
evenly, the
amount needed
and tape to
paper.
CUTTING LINE
C
D
Cutting/Marking
SINGLE THICKNESS
A
18
16
15
B
[email protected]
General Directions
12
8
E-mail
SELVAGE
1
http://www.simplicity.com
1-888-588-2700
3
e
CROSSWISE FOLD
Thank you for purchasing this Simplicity pattern.
We have made every effort to provide you with a high quality product.
Gracias por haber comprado este patrón de Simplicity.
Hemos hecho todos los esfuerzos para ofrecerle un producto de alta calidad.
Web Site
U.S. & Canada Toll-Free
18 pieces given
✁
2886
®
FOLD
C VESTIDO USE LAS PIEZAS 4 5 6 7 8 10 12
SELS.
LA PIEZA 14 SE CORTA EN EL ELASTICO
3A 44" 45" (115CM) CON PELUSA/ TODAS LAS TALLAS
3B 58" 60" (150CM) CON PELUSA/ TODAS LAS TALLAS
CONTRASTANTE USE LAS PIEZAS 9 11 13 15 16
13
SELS.
3C 44" 45" (115CM) CON PELUSA/ TODAS LAS TALLAS
Double Thickness= Espesor Doble
Single Thickness=Espesor Sencillo
Bordered Edges=Borde con ribete
Crosswise Fold=Doblez transversal
SIGA EL DIAGRAMA DE CORTE PAGINA 2
English/Spanish 3
2/4
SELVAGES
USE PIECES 2 8 12
SINGLE THICKNESS
3D 58" 60" (150CM)
WITH NAP
ALL SIZES
8
WITHOUT NAP
ALL SIZES
11
12
9
2
FOLD
13
USE PIECES 2 9
13
16
SELVAGES
17
18
FOR LINING FOLLOW SAME LAYOUT
FOLD
4B 20" TO 25" (51CM TO 64CM) FUSIBLE
ALL SIZES
SELVAGE
17
5B 58" 60" (150CM)
WITH NAP
ALL SIZES
2
Sewing Directions
FABRIC
KEY
RIGHT SIDE
WRONG SIDE
INTERFACING
FOLD
9
29
4B 20" A 25" (51CM A 64CM) ADHESIVA
TODAS LAS TALLAS
D CHAQUETA USE LAS PIEZAS 17 18
5A
44" 45" (115CM) CON PELUSA/TODAS LAS TALLAS
PARA EL FORRO SIGA EL MISMO DIAGRAMA
Selvage (s) / Sel. (s)= Orillo(s)
Fold= Doblez
9. With RIGHT sides together, pin midriff lining to lower edge of
bodice lining, matching centers front, having raw edges even.
Stitch seam, stitching through all thicknesses.
Press midriff and midriff lining down. Baste raw edges
together.
10
LINING
Read General Directions on page 1 before you begin.
STAY-STITCHING
ENTRETELA USE LAS PIEZAS
5B 58" 60" (150CM) CON PELUSA/TODAS LAS TALLAS
18
SELS.
2 8 12
4A 44" 45" (115CM) SIN PELUSA/TODAS LAS TALLAS
SELS.
9
3D 58" 60" (150CM) CON PELUSA/TODAS LAS TALLAS
B,C FORRO USE LAS PIEZAS
WITH NAP
ALL SIZES
SELVAGES
INTERFACING
15
USE PIECES 17 18
5A 44" 45" (115CM)
4A 44" 45" (115CM)
SELVAGE
Español
D JACKET
B,C LINING
CROSSWISE
FOLD
2886
10. On RIGHT side seam, open out bodice back lining.
With RIGHT sides together, baste bodice front to bodice back
at RIGHT side seam, placing upper edge of bodice front at
underarm seam on back.
NOW...bring bodice back lining and upper seam allowance
over front at side seam. Stitch side seam through all
thicknesses. Trim seam.
1
DRESS A, B, C
2
NOTE: Determine finished length before sewing.
11
3
4
BODICE A
11. Turn lining to INSIDE; press. Baste remaining raw edges
together.
1. Stay-stitch front and back neck edges 1/2" (1.3cm) from cut
edge in direction of arrows.
This stitching stays in permanently and helps prevent
stretching on curved edges.
Stay-stitching will not be shown in the following illustrations.
BODICE B, C
12
12. Machine-stitch bodice front armhole edges along seam line.
Clip armhole edges to stitching. With RIGHT sides together,
stitch center front seam of bodice front from lower edge to
small dot. Back-stitch at small dot to reinforce seam. Trim
seam.
2. Stitch bodice front to bodice back sections at shoulder
seams.
3. Stitch bodice front lining to bodice back lining sections at
shoulder seams.
With RIGHT sides together, pin bodice lining to bodice
matching centers and shoulder seams.
Stitch neck edge along stitching lines and seam lines. To
reinforce seam at center front, stitch over first stitching.
Trim seam; clip curves and to stitching at center front.
Stitch armhole edge. Trim seams; clip curves.
6
5. Open out lining at center back edges. With RIGHT sides
together, in one continuous stitching, stitch entire center back
seam from lower edge of bodice to edge of lining, matching
seams.
13. Apply fusible interfacing to WRONG side of bodice front band
sections, following manufacturer’s directions. Stitch center
front seam between small dots. Back-stitch at small dots to
reinforce seam. Trim seam. To reinforce small dots at inner
corners, machine-stitch along seam line 1" (2.5cm) on each
side of small dots. Clip to small dots at inner corners, being
careful not to clip through stitching.
14
13
4. Turn lining to INSIDE by pulling each back through front at
shoulder seam. Press.
5
NOTE: You have cut four bodice front band sections. Two will be
referred to as facing.
15
16
17
18
14. With RIGHT sides together, pin bodice front band to bodice
front matching small dots, having raw edges even.
Stitch seam. Trim seam and corners. Clip curves. Press
seam up, pressing band out.
15. Fold shoulder strap in half, lengthwise, with RIGHT sides
together. Stitch in 3/8" (1cm) seam, leaving ends open.
16. Turn strap RIGHT side out; press.
6. Turn lining back to INSIDE; press.
Baste raw edges of bodice front together
7. To make pleats on lower edge of bodice front, on OUTSIDE,
fold along solid lines.
Bring folds to broken lines; pin.
Baste across raw edge.
7
17. On OUTSIDE, pin front end of strap to upper edge of bodice
front band, matching small and large dots, having raw edges
even. Baste.
19
8
8. Apply fusible interfacing to WRONG side of midriff front,
following manufacturer’s directions.
With RIGHT sides together, pin upper edge of midriff front to
lower edge of bodice front, matching centers front, having
raw edges even. Baste.
© Copyright 2008—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
20
18. Machine-stitch bodice front lining armhole edges along seam
line. Clip armhole edges to stitching. With RIGHT sides
together, stitch center front seam of bodice front lining from
lower edge to small dot. Back-stitch at small dot to reinforce
seam. Trim seam.
19. Stitch center front seam of bodice front band facing between
small dots. Back-stitch at small dots to reinforce seam. Trim
seam. To reinforce small dots at inner corners, machine-stitch
along seam line 1" (2.5cm) on each side of small dots. Clip to
small dots at inner corners, being careful not to clip through
stitching.
20. With RIGHT sides together, pin bodice front band facing to
bodice front lining, matching small dots, having raw edges
even. Stitch seam. Trim seam and corners. Clip curves. Press
seam up, pressing band out.
English/Spanish 3
2886
3/4
28
28. With RIGHT sides together, stitch bodice back lining to
bodice back along upper edge. Trim seam.
21
21. With RIGHT sides together, pin bodice lining to bodice,
matching centers front, having raw edges even. Stitch seam.
Trim seam and corners; clip curves.
29
22
23
22. Turn lining to INSIDE; press.
Baste raw edges together.
To gather lower edge of bodice front between notches, stitch
along seam line and 1/4" (6mm) INSIDE seam line, using a
long machine stitch.
29. Turn lining to INSIDE; press. On OUTSIDE, stitch 3/8" (1cm)
from upper edge, forming casing. Baste raw edges together
below casing stitching.
30
23. To make tucks on midriff front, on OUTSIDE, bring broken
lines together. Stitch along broken lines.
Press tucks down.
Baste across side edges.
30. Cut a piece of elastic the length of back elastic guide. Insert
elastic through casing, having raw ends even. Stitch across
ends of casing, catching in elastic.
31
24
32
24. With RIGHT sides together, pin upper edge of midriff front to
lower edge of bodice front, matching centers front, having
raw edges even. Pull up gathering stitches to fit. Baste.
31. With RIGHT sides together, stitch bodice front to bodice back
at RIGHT side seam.
32. Turn under seam allowance diagonally at upper edge of
RIGHT side seam. Slip-stitch in place.
CONTINUE AS FOLLOWS FOR ALL VIEWS
25
33
33. With RIGHT sides together, pin pocket facing to skirt front,
matching small dots. Stitch single notched edge. Trim seam;
clip curves.
25. Apply fusible interfacing to WRONG side of midriff front lining,
following manufacturer’s directions.
With RIGHT sides together, pin midriff lining to lower edge of
bodice lining, matching centers front, having raw edges even.
Stitch seam, stitching through all thicknesses.
Press midriff and midriff lining down. Baste raw edges
together.
34. Turn facing to INSIDE; press.
26
34
35
26. Fold tie end in half, lengthwise, with RIGHT sides together.
Stitch in 3/8" (1cm) seam, leaving end with small and large
dots open. Trim seam and corners.
35. On INSIDE, with RIGHT sides together, pin yoke front and
pocket section to pocket facing, having raw edges even.
Stitch double-notched edge.
27
27. Turn tie end RIGHT side out; press.
On OUTSIDE, pin tie to midriff front, matching small and
large dots, having raw edges even. Baste.
36
37
36. With RIGHT sides together, pin front and pocket facing to
yoke front, matching small dots. Stitch along seam line on
skirt seam allowance from lower small dot to upper edge,
stitching through all thicknesses. Back-stitch at small dot to
reinforce seam.
37. On OUTSIDE, lap skirt front over yoke and pocket section,
matching small dots, having raw edges even. Baste side and
upper edges together.
© Copyright 2008—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.
English/Spanish 3
2886
4/4
44
44. Fold skirt band in half, with WRONG sides together. Pin raw
edges together. With RIGHT sides together, pin band to lower
edge of garment, matching centers and side seams. Stitch
seam. Stitch again 1/4" (6mm) away from first stitching within
the seam allowance.
Press seam up, pressing band down.
38
38. With RIGHT sides together, stitch front to back at side seams,
stitching LEFT side from lower edge to notch. Back-stitch at
lower edge of opening to reinforce seam.
SHOULDER STRAPS B, C
45
45. On INSIDE, pin shoulder straps to upper edge of bodice
back, matching small and large dots. You will notice that the
straps have extra allowance at the back edge...this is for
adjustment. Try on dress and adjust length of straps in back
so that they fit comfortably. Re-pin and trim excess if
necessary. On OUTSIDE, stitch across straps along casing
stitching.
39
BOLERO D
1
2
40
39. To make pleats at center front and center back, on OUTSIDE,
fold along solid lines; bring folds to center. Baste close to fold.
To make remaining pleats, on OUTSIDE fold along solid
lines; bring folds to broken lines. Baste close to fold. Press.
Machine-baste across upper edge. Remove fold basting.
1. To make pleats on bolero front, on OUTSIDE, fold along solid
lines.
Bring folds to broken lines; pin.
Baste across raw edge.
2. To make pleat on center back, on OUTSIDE, fold along solid
lines.
Bring folds to center; pin.
Baste across raw edge.
3
40. With RIGHT sides together, stitch skirt to bodice at waistline
seam, matching centers, RIGHT side seams and LEFT side
opening edges.
Press seam toward bodice.
3. With RIGHT sides together, stitch front to back at shoulder
seams.
41
4
4. Make pleats in lining in same manner as for garment. Stitch
shoulder seams of lining.
With RIGHT sides together, pin lining to bolero, matching
centers and shoulder seams, having raw edges even.
Stitch lining to bolero, leaving side seams open for turning.
Trim seams and corners; clip curves.
41. Press under 5/8" (1.5cm) on LEFT front opening edge and
1/2" (1.3cm) on LEFT back opening edge.
Pin LEFT back edge to zipper tape, placing pressed edge
close to zipper teeth and lower end of zipper at lower end of
opening. Turn upper end of zipper tape over seam allowance.
Baste. Pin and baste LEFT back edge to zipper tape, lapping
LEFT back 1/8" (3mm) over RIGHT back. Turn upper end of
zipper tape over seam allowance. Baste. Stitch as basted,
using an adjustable zipper foot.
5. Turn bolero RIGHT side out by pulling each front through
shoulder and out one of the back side openings, as shown;
press.
42
HEM A, B
42. Press up hem.
To EDGE FINISH the raw edge...stitch under 1/4" (6mm), zigzag, OR overlock/serge.
Slip-stitch OR machine-stitch hem in place.
43
5
6
6. With RIGHT sides together and raw edges even, pin bolero
and lining at sides, matching armhole seams and lower
seams.
To stitch, begin on lining 1" (2.5cm) above armhole seam;
stitch bolero seam and end on lining 1" (2.5cm) below lower
seam edge. Press seam open.
Turn in seam allowances of remaining lining edges and slipstitch together.
SKIRT BAND C
7
43. Stitch skirt front band to skirt back band at side seams.
7. Make buttonhole in RIGHT front.
Lap RIGHT front over LEFT, matching centers.
Sew button under buttonhole.
© Copyright 2008—Simplicity Pattern Co., Inc. / Printed in U.S.A. / Simplicity is a registered trademark of Simplicity Pattern Co., Inc.