FOLD ~ Drill holes for pipes in rear of unit... with appropriate size hole saw.

T H A N K Y OU F O R Y OUR P U R C H A S E O F
A N E S S E N T I A V A N I T Y, P L E A S E R E A D T H E S E V A N I T Y
C A R E A N D I N S T A L L A T I O N I N S T R U C T I O N S C A R E F U L LY
CARE AND CONDITIONS OF USE
It is important that your bathroom is adequately ventilated to eliminate moisture
build up. High humidity will lead to permanent dampness and mould resulting
in a deterioration of the materials in your bathroom.
Vanity tops - Acrylic, Mineral Cast and Ceramic
Essentia vanity tops are manufactured from the finest materials and when
treated with care will last for many years. Vanity tops must not be subjected to
water temperatures above the recommended safety level of the power boards
ie: 55ºC or come into contact with solvents or strong chemicals.
Keep heat away from the vanity top and avoid metal or other sharp objects
which could scratch and damage the surface.
Ceramic Vanities
Due to ceramic vanities being hand-crafted and individually customised,
and because china is fired at high temperatures, some visual distortion may
be evident – but we feel that this adds to the natural beauty of the product.
Care of your vanity top
To clean your vanity top simply wipe over with a damp cloth after each use. For
best results, St Michel recommends you use one of the listed household cleaners.
~ Ajax Spray n’ Wipe
~ Duck Bathroom Spray
~ Jif Power Spray
~ Brasso – to remove stubborn marks
Do not use abrasive cleaners, chemicals, disinfectants, acetone, alcohol or
cleaners which incorporate isopropyl alcohol.
N.B. The use of cleaners incorporating ingredients which have been identified
as having harmful effects on the acrylic and composite stone surfaces will void
the St Michel warranty.
Cabinets
Essentia cabinets are manufactured from quality melamine or thermal laminate
board (durashell).
Materials used are water resistant and not water proof. To ensure long life of the
cabinet, water must not be allowed to remain on the cabinet surfaces. All water
spillages, leaks or flooding in or around the cabinet must be sponged off and
dried immediately.
the vanity
cabinet
and avoid
or other
objects
KeepKeep
heat heat
awayaway
fromfrom
the vanity
cabinet
and avoid
metalmetal
or other
sharpsharp
objects
which
scratch
and damage
the surface.
which
couldcould
scratch
and damage
the surface.
of your
vanity
cabinet
Care Care
of your
vanity
cabinet
The vanity
cabinet
can
be cleaned
soft damp
a liquid
The vanity
cabinet
can be
cleaned
usingusing
a softadamp
clothcloth
with with
a liquid
household
cleaner
dryalloff
all surfaces
cleaning.
household
cleaner
~ dry~off
surfaces
after after
cleaning.
Abrasive
cleaners
should
be used.
Abrasive
cleaners
should
nevernever
be used.
A TNI O
C TNISO N S
I N S TI N
A SL TL AA LT LI O
I NNS TI NR SUTCRTUI O
It is recommended
a qualified,
licensed
trades
person
It is recommended
that athat
qualified,
licensed
trades
person
installinstall
your your
unit. unit.
To ensure
satisfaction
vanity
it is important
the vanity
is installed
To ensure
total total
satisfaction
with with
your your
vanity
it is important
the vanity
is installed
correctly
andconditions
the conditions
ofare
usenoted.
are noted.
correctly
and the
of use
NOTE:
Detailed
instructions
forinstaller
the installer
are supplied
St Michel
NOTE:
Detailed
instructions
for the
are supplied
with with
all Stall
Michel
vanitiesprovide
pre installation
instructions
(summarized
below)
vanitiesthey they
provide
pre installation
instructions
(summarized
below)
and and
that
the event
thatvanity
the vanity
not installed
in accordance
statestate
that in
theinevent
that the
is notisinstalled
in accordance
with with
the the
instructions
St Michel
warranty
maybe
voided
andhomeowner
the homeowner
instructions
the Stthe
Michel
warranty
maybe
voided
and the
may may
a claim
against
the installer.
havehave
a claim
against
the installer.
[ A sample
copybecan
be downloaded
from www.stmichel.co.nz
]
[ A sample
copy can
downloaded
from www.stmichel.co.nz
]
This vanity
carries
full warranty
against
workmanship
and material.
This vanity
carries
a fullawarranty
against
faultyfaulty
workmanship
and material.
Please
inspect
thoroughly
before
installation
to ensure
this has
unitnot
hasbeen
not been
Please
inspect
thoroughly
before
installation
to ensure
this unit
damaged
in transit
the warranty
not cover
the of
cost
of removal
damaged
in transit
as theaswarranty
doesdoes
not cover
the cost
removal
and and
installation
installed.
installation
onceonce
installed.
temperature
WaterWater
temperature
First ensure
hot water
set below
for safety
and
to avoid
possible
First ensure
your your
hot water
is setisbelow
55°C 55°C
for safety
and to
avoid
possible
damage
to your
vanity
damage
to your
vanity
basin.basin.
Installation
Installation
positioning
the vanity
unit consider
the following
points.
WhenWhen
positioning
the vanity
unit consider
the following
points.
~
~ Check
thatfloor
the floor
is level
for floor
standing
vanities
andwall
the is
wall is
Check
that the
is level
for floor
standing
vanities
and the
straight
ie:bowed
not bowed
or twisted
for hung
wall hung
vanities.
straight
ie: not
or twisted
for wall
vanities.
~
~ Leave
gap
at least
150mm
between
the bath
andvanity
the vanity
cabinet.
Leave
a gapa of
at of
least
150mm
between
the bath
and the
cabinet.
VANITY TOPS
Acrylic &
Mineral
Cast
Some models are supplied with the top loose (for merchant
flexibility) and require fixing in situ. If your top is not attached
to the cabinet it is easier to fit the taps and waste fitting prior to
gluing. The top can be fastened to the cabinet using Expandite
SB Adhesive, Panel Bond or similar. Spot gluing only is required.
Ceramic
The process of manufacturing ceramic products is highly complex.
During its manufacture the product shrinks significantly and can
result in the product being slightly uneven. It is recommended that
the ceramic top be fixed onto the cabinet with silicone.This will
ensure the top will not rack or move once installed. Apply silicone
to side top edges of the cabinet. If Ceramic tops are fitted to wall
hung cabinets the ceramic top should be fixed to the wall with the
fasteners supplied.
All vanity tops should have a bead of silicone (especially formulated for
bathroom use) applied between the rear upstand or back edge and the wall.
Ensure silicone is used according to manufacturer’s instructions.
CABINETS
Floor Standing
~
Ensure the floor is level or the vanity is packed under the base
to make the vanity level.
~
Drill holes for pipes in base and rear of unit (if applicable) with appropriate
size hole saw.
~
Position unit, check cabinet is sitting level and square and screw fix to wall.
Wall Hung
~
Ensure the wall is straight (horizontal and vertical).
~
Do not screw fix the cabinet to a bowed wall as it will twist the cabinet
and distort the door alignment.
~
Decide appropriate height for work surface of vanity top.
Recommend between 840 and 900mm.
~
Deduct the thickness of the vanity top / basin or vessel basin and this
becomes the fixing height to the top of the vanity cabinet.
~
Drill holes for pipes in rear of unit and base (if applicable)
with appropriate size hole saw.
~
Position unit, check cabinet is sitting level and square and screw fix to wall fixings should be into solid timber and be within 150mm of each side.
I M P O R TA N T
A bead of sealant especially formulated for bathrooms should be used to seal
all edges where water penetration may occur ie: between cabinet and wall,
cabinet and floor. Where a basin or vessel basin is to be fitted it is
essential that the basin be fully sealed to the cabinet and top to prevent
any water penetration.
HINGES
Essentia use clip hinges which require only light finger pressure to clip into
place and allow the doors to be easily removed for access to plumbing fittings.
Door Alignment
Your doors have been adjusted in the factory on a level surface to achieve
matching height, equal gap and surface alignment. Before you adjust the
doors ensure again that the vanity is level and true and not twisted
(see cabinet instruction previous). If when level the doors still do not align,
adjustment can be made to the hinges as follows:
A. Side adjustment - to move the doors sideways in total or to level each
door - turn screw A clockwise or anticlockwise.
B. Depth adjustment - to move the door inward or outward from the carcass loosen the hinge arm
fastening screw B and
slide in the direction
you want to go.
Retighten hinge arm
fastening screw B.
C. Height adjustment loosen the top and
bottom screw C on
each mount plate,
adjust and retighten.
WARRANTY
Ceramic
2 years
Acrylic
5 years
Polymarble
5 years
Mineral Cast
5 years
Furniture
5 years
Mirror cabinets
2 years
Mirrors
2 years
Subject to Conditions of Use
St Michel warrants that in the manufacture and supply of its products only high
quality materials and workmanship have been used.
If within the warranty period there should be a fault with either materials or
workmanship St Michel will either (at its sole discretion) repair or replace or
refund (up to the original purchase price of the product).
Costs incurred in removing the defective product and installing the
replacement product remain the responsibility of the purchaser.
This guarantee does not cover damage by improper installation, abuse,
accident, misuse, excessive wear and tear, negligence, neglect, natural causes
eg: water and sunlight, improper care and maintenance, water temperatures in
excess of 55ºC, humidity and other environmental conditions.
Essentia warranty applies from the date of purchase. Proof of the purchase date
needs to be produced by the purchaser when making a claim.
ST MICHEL INDUSTRIES LTD
PO Box 21-122, Henderson, Auckland. Phone: (09) 837 4276 Fax: (09) 837 4325
AUGU ST 2010