Woodstove Permits For installation in site-built structures

Transcription

Woodstove Permits For installation in site-built structures
Woodstove Permits
For installation in site-built structures
The installation of solid fuel-burning
appliances (woodstoves, factory built
fireplaces, pellet stoves and inserts, etc) in
site-built structures shall be installed per
manufacture listing. If you have a mobile or
modular home, please contact the
Washington State Department of Labor and
Industries at 312 Stonemill Drive, Suite 120
in Vancouver, telephone (360)896-2371 for
a woodstove permit.
Permits required for all stoves and
inserts
Permits are required for the installation of
all solid fuel burning appliances. A permit
for the installation of a woodstove can be
obtained from the Clark County Permit
Center, located on the first floor of the
Public Service Center at 1300 Franklin
Street, Vancouver. If a contractor is
installing the stove, the contractor’s valid
license card must be submitted with the
permit request.
Listed woodstoves and inserts
Woodstoves and inserts are required to be
approved or “listed” by approved testing
agencies such as Underwriters Laboratories
(UL). These units have been tested and
approved under extreme conditions.
All new woodstove and fireplace
insert installations must meet State
of Washington Emission Standards.
These “listed” stoves and inserts must be
installed according to the manufacturer’s
instructions, and the instructions must be
posted with the permit at the time of the
Building Inspector’s visit. The
manufacturer’s metal placard must remain
affixed to the stove for the duration of the
installation in the structure.
Unlisted woodstoves and inserts
Unlisted appliances are any appliances that
have not been approved by a recognized
testing agency. An insert is any part of the
appliance that fits inside the firebox. All
fireplace inserts installed in Clark County
must be listed.
Used woodstoves and inserts
No used solid fuel burning device shall be
installed in new or existing buildings unless
such device is certified to meet the State of
Washington Emissions Standards. Lists of
State of Washington approved woodstoves,
pellet stoves, fireplaces, and masonry
heaters are available at www.ecy.wa.gov by
entering “woodstove fireplace information”
in the search box. You can also call
Revised 7/1/13
Community Development Department
1300 Franklin Street, Vancouver, Washington
Phone: (360) 397-2375 Fax: (360) 397-2011
www.clark.wa.gov/development
For an alternate format,
contact the Clark County
ADA Compliance Office.
Phone: (360)397-2322
Relay: 711 or (800) 833-6384
E-mail: [email protected]
Woodstove Permits
Southwest Clean Air Agency at (360) 5743058 or (800) 633-0909.
Exception: antique wood cook stoves and
heaters manufactured prior to 1940.
Floor protection under stoves and
inserts
Solid fuel-burning appliances: The
clearance reduction models specified in
Table 308.6 of the Mechanical Code shall
not be utilized to reduce the clearance
required for solid fuel-burning appliances
that are labeled for installation with
clearances of 12 inches (305 mm) or less.
Where appliances are labeled for
installation with clearances of greater than
12 inches (305 mm), the clearance
reduction methods of Table 308.6 shall not
reduce the clearance to less than 12 inches
(305 mm).
Hearth extensions (inserts)
Hearths should be installed for use with any
fireplace or insert. Hearths should extend at
least 16 inches from the front of the firebox
opening and at least 8 inches beyond each
side of the stove/insert.
The standard minimum clearance from the
firebox to a combustible wall is 36 inches. If
there is not enough space in the room to
accomplish this, a noncombustible heat
shield may be created using the materials
and clearances shown in figure 1.
Thicknesses shown for materials are
minimums only. All clearances should be
measured from the outer surface of the
appliance to the combustible material
disregarding any intervening protection
applied to the combustible material.
Revised 7/1/13
Building Safety
Spacers must be of approved noncombustible material such as metal,
ceramic, concrete, brick or stone.
All synthetic rock, decorative material, or
adhesive used in the installation must be
listed and approved as a non-combustible
material by an approved testing agency.
Sheetrock is not an approved
material for wall protection.
Combustion air
Woodstoves are required to have tight
fitting metal or ceramic glass doors. They
are required to have a source from outside
the structure of primary combustion air,
connected to the appliance as per the
manufacturer’s specifications. The air inlet
shall originate as a point below the fire box.
The duct shall be four inches or greater in
diameter, not exceed 20 feet in length, and
be installed as per manufacturer’s
instructions; or be certified and tested and
modified as required by WAC R1006.2
Chimneys
Chimneys shall be constructed of masonry
in accordance with the current adopted
version of the 2012 International
Residential Code and the 2012
International Mechanical Code or they shall
be approved, factory-built assemblies
“listed” and approved by Underwriters
Laboratories (UL) or other recognized
agencies for use with wood burning or other
solid fuel-burning appliances. The approved
chimney assemblies shall be installed in
accordance with their listings. The required
clearance from the chimney to combustibles
will be indicated on each section of
Page 2 of 4
Woodstove Permits
chimney. The minimum clearance for a
masonry chimney is two inches. All
chimneys must have a cleanout and an
approved liner. Metal liners installed in
masonry chimneys or relined
chimneys shall be of approved
“listed” materials and installed in
accordance with the listing.
Building Safety
Note: ‘A’ represents the typical
horizontal dimension reduction
allowed by Table 308.6 of the
International Mechanical Code.
Chimney connectors
A chimney connector shall not be connected
to a chimney flue serving a fireplace. When
installing the connector (stovepipe) to the
chimney, you must maintain 18 inches of
clearance between the pipe and any
combustible material, or use approved
material to reduce clearance, or use an
approved and “listed” chimney connector.
Chimney connectors shall be pitched
upward from the appliance at least onequarter inch per foot. There should be no
dips, sags, or downward pitch from the
appliance. A connector shall be as short and
straight as possible, and shall be securely
supported, with joints fastened with 3 sheet
metal screws, rivets, or other approved
means. The appliance shall be located as
close as practical to the chimney.
Chimney height termination
The chimney shall terminate at a point not
less than two feet above any portion of a
structure within a 10 foot radius of the
chimney.
Revised 7/1/13
Required clearances
Type of Protection for
Radiant Appliances
Required clearances from
Combustible Materials
Above
Sides
and
Rear
Chimney
Connector
36”
36”
18”
18”
12”
6”
3. Three and a half inch
brick wall spaced one inch
and vented
NP
12”
6”
4. Half inch inorganic
insulating board over one
inch mineral wool batt
against combustible
assembly
24”
18”
9”
1. None
2.Number 28
Manufacturer’s 24 gage
steel spaced one inch and
vented
Page 3 of 4
Woodstove Permits
Building Safety
Typical woodstove or fireplace stove
installation
REDUCED
CLEARANCE
PER TABLE
308.6 IMC WITH
APPROVED
MATERIALS
Revised 7/1/13
Page 4 of 4