Any claim shall be deemed waived The following trademarks used

Trademarks
The following trademarks used
herein are owned by United States
Gypsum or a related company:
Durabond, Easy Sand, Sheetrock.
Product Information
See usg.com for the most
up-to-date product information.
Note
Products described here may not
be available in all geographic
markets. Consult your U.S.
Gypsum Company sales office or
representative for information.
Notice
We shall not be liable for incidental and consequential damages,
directly or indirectly sustained, nor
for any loss caused by application
of these goods not in accordance
with current printed instructions
or for other than the intended use.
Our liability is expressly limited to
replacement of defective goods.
Any claim shall be deemed waived
unless made in writing to us within
thirty (30) days from date it was
or reasonably should have been
discovered.
Safety First!
Follow good safety and industrial
hygiene practices during handling
and installation of all products and
systems. Take necessary precautions and wear the appropriate
personal protective equipment as
needed. Read material safety data
sheets and related literature on
products before specification and/
or installation.
For product information
and literature:
800 USG.4YOU (874.4968)
usg.com
Manufactured by
United States Gypsum Company
550 West Adams Street
Chicago, IL 60661
J1124/rev. 5-07
©2007, United States Gypsum Company
Printed in U.S.A.
Sheetrock
Paper-Faced
Metal Bead
and Trim
™
installation
guide
Provides superior performance
for cost-effective installation
Helps minimize edge cracking
for reduced callbacks
Sheetrock™ brand paper-faced metal bead and
trim can easily be applied using a number of
different tools and methods. Three are outlined in
this folder:
–Hand-tool method
–Hopper-and-roller method
–Mechanical angle applicator method
Hand-Tool Method
Whichever method
you choose, you will
need a few simple tools:
Tin snips
Drywall taping knives
(4, 6, and 8 or 10)
Mud pan
Hand or pole sander
and sandpaper
Sponge
1 Measure length of corner and
cut trim to length with metal
snips. For vertical wall installations, cut the corner trim
1/2 (12.7 mm) shorter than
the wall height.
2 Using a 4 taping
1 knife, apply
ready-mixed Sheetrock® joint
compound (taping, all-purpose,
or lightweight all-purpose)
or Sheetrock® Durabond® or
Easy Sand™ setting-type joint
compound to drywall slightly
beyond where the edge of
the trim will be positioned.
(For outside corners, extend
compound approximately
2 or 50 mm from the corner
on each side; for inside
corners, extend 1-1/2 or
38 mm from the corner on
each side.) Hint: For this step,
2 slightly with
thin compound
water. Add water in small
increments (for one gallon of
compound, add1water in 2 oz.
increments) and mix. Be
careful not to over-thin.
2
PG 3. Paper Faced Metal Bead and Trim Installation Guide Illustrations
3
Start with Quality
2
3 Place trim on wall and press
into position. Corner bead
should be pressed tight to
ceiling. Embed trim by running the knife over it with
even pressure at a 45° angle.
6 Use an 8 or larger finishing
knife for outside corners (46 knife for inside cor­ners) to
apply a finishing coat of compound. (Do not use Durabond
or taping joint compound for
this step.) Feather
4 compound
8 (200 mm) from nose of
trim for outside corners
(1 (25 mm) past previous coat
for inside corners).
Let dry; sand and prime.
3
3
4
4 Use the knife (or a damp
sponge) to remove excess
compound, eliminating any
air bub­bles under the paper.
Allow to dry.
5
6
PG 4 Paper Faced Metal Bead and Trim Installation Guide Illustrations
Start with Quality Products
5 Using a 6 taping knife for
outside corners (4 for in­side
corners), apply
5 a second coat
6
of joint compound as smoothly
PG 4 Paper
Metal Bead
andnot
Trimuse
Installation Guide Illustrations Start with Quality Products
asFaced
possible.
(Do
Durabond or taping joint compound for this step.) Feather
out 5 to 6 (125 to 150 mm)
from the nose of the trim on
each side for outside corners
(1 (25 mm) past previous
coat for in­side corners). Let
dry. Sand sides lightly where
needed.
4
Hopper-andRoller Method
1 M
easure length of corner and
cut trim to length with metal
snips. On vertical wall installations, cut the corner trim 1/2
(12.7 mm) shorter than the
wall length.
1
1
4
5 Using a 6 taping knife for
outside corners (4 for inside
corners), apply a second coat
of joint compound. (Do not use
Durabond or taping joint compound for this step.) Feather
2
out 5 to 6 (125 to 150 mm)
2 on each
from nose of trim
side for outside corners (1
(25 mm) past previous coat for
inside corners).
45 Let dry. Sand
sides lightly where needed.
1 hopper
2 Pass trim through
containing ready-mixed
1
Sheetrock joint compound
(taping, all-purpose, or
lightweight
all-purpose)
1
12
or Sheetrock Durabond or
Easy Sand setting-type joint
compound.
1
1
4
6 Use an 8 or56larger finishing
32
2
knife for outside
corners
1
4
aper Faced1
Metal Bead and Trim Installation Guide Illustrations Hopper and Roller Method
3 Place trim on2wall and use roller
(4-6 knife for inside
to press into position. Corner
bead should
2 be pressed tight
to ceiling.
corners) to apply a finishing
coat of compound. (Do5not
use Durabond or taping joint
compound for this step.)
Feather compound 8
(200 mm) from nose of trim
on each side for outside
corners feather
6 (1 (25 mm)
past previous coat for inside
Hopper
and Roller
5 dry; Method
corners).
Let
sand
and prime.
3
2
aper Faced Metal Bead and Trim Installation Guide Illustrations
6
3 knife (or a damp
4 Use a 4 taping
toMetal
remove
excess
PG 5sponge)
Paper Faced
Bead and
Trim Installation Guide Illustrations Hopper and Roller Method
compound, eliminating any air
bubbles under the paper. Allow
to dry.
3
per Faced Metal Bead and Trim Installation Guide Illustrations
5
6
Hopper and Roller Method
Mechanical Angle
Applicator
Method
1
4
1 Measure length of corner;
cut trim to length with metal
snips. On vertical wall installations, cut the corner trim
1/2 (12.7 mm) shorter
than the wall height.
2
1
4
1 Sheetrock
2 Apply ready-mixed
joint compound (taping,
45
all-purpose, or lightweight
all-purpose) or Sheetrock
2 Durabond or Easy Sand
3 setting-type joint compound
Paper Faced Metal Bead
and Trim Installation
Guide Illustrations
to drywall
using mechanical
angle applicator.
5 Using a 6 taping knife for outside
5
corners (4 for inside corners),
apply a second coat of joint
compound as smoothly as possible. (Do not use Durabond or
taping joint compound for this
2 5 to 6 (125
step.) Feather out
to 150 mm) on each side from
nose of trim for outside corners
(1 (25 mm) for inside corners).
Let dry. Sand sides lightly where
needed. 5 6
Mechanical Angle Applicator Method
1
4
45
1
4
6 finishing
6 Use an 8 or larger
3
2
knife
for
outside
cornersMethod
(4-6
Paper Faced Metal Bead and Trim Installation Guide Illustrations
Mechanical Angle Applicator
2 and press
knife for inside corners) to apply
3 Place trim on wall
a finishing coat of compound.
into position. Corner bead
(Do not use Durabond or taping
should be pressed tight to
joint compound for this step.)
ceiling. Embed trim by runFeather compound 8 (200 mm)
ning the knife over it with
2 at a 45° angle.
5 corfrom nose of trim for outside
even pressure
ners (1 (25 mm) past previous
coat for inside corners). Let dry;
2
5
sand and prime.
45
ipe off excess compound
W
3
with a damp sponge (or a 4
PG 6 Paper Faced Metal Bead and Trim Installation Guide Illustrations
taping knife), eliminating any
air bubbles under the paper.
3
Allow to dry.
6 Paper Faced Metal Bead and Trim Installation Guide Illustrations
6
454 6
Mechanical Angle Applicator M
6
Mechanical Angle Applicator Method
How to Install
Corner Caps
How to Install
Transition Caps
1 Position corner cap and tack
into place with one fastener
to allow for adjustment.
1 Measure distance between
floor and end of bead to
determine transition cap
length required.
1
1 over align2 Slide corner bead
ment tongue on
1 each end of
corner cap. Be sure beads
align and seams are tight.
3 Fasten corner3cap into permanent position and press
2
corner beads into place with
2 damp sponge.
roller tool or
3
2 Cut transition cap to appropri3
ate length. 1
3 Place joint compound on back
of transition2cap and position
on the wall. Press tight.
PG 7(2 ) Paper Faced Metal Bead and Trim Installation Guide Illustration
4
PG 7(1) Paper Faced Metal Bead and Trim Installation Guide Illustrations
4
How
2 to Install Corner Caps
How to Install Corner Caps
PG 7(2 ) Paper Faced Metal Bead and Trim Installation Guide Illustrations
PG 7(1) Paper Faced Metal Bead and Trim Installation Guide Illustrations
1
3 bead over
4 Place corner
transition cap3 tongue. Press
corner bead into place with
roller tool or wet sponge.
1
4
How to Install Corner Caps
uide Illustrations
4
2
2
Paper Faced Metal Bead and Trim Installation Guide Illustrations
7
How to Install4Corner Caps
7(2 ) Paper Faced Metal Bead and Trim Installation Guide Illustrations
How to Install Corner Caps