How to Use a Power Paddle Introduction

How to Use a Power Paddle
Introduction
The power paddle provides a temporary power source to the NXT and
NXT Wireless (blue) series lockboxes. If the internal batteries in the
lockbox are dead, you will need a temporary power source to allow you to
open the key compartment and replace the internal lockbox batteries.
Note: It is important to read through these directions before you
use the power paddle at a lockbox.
To determine if the lockbox batteries are dead, insert your SentriCard®
into the lockbox and press the lockbox keypad buttons. If the lights on the
lockbox do not illuminate and the lockbox does not make any sounds, the
batteries are dead.
Note: Before the lockbox batteries die, the lockbox will alert you.
When you insert your SentriCard® into the lockbox, followed by
entering your PIN, the lockbox will illuminate the MESSAGE light.
The MESSAGE light indicates it is time to replace the lockbox
batteries. Once the MESSAGE light illuminates, you will have a
couple of weeks (depending upon lockbox usage) to replace the
lockbox batteries. When the MESSAGE light illuminates SentriLock
recommends replacing the lockbox batteries as soon as possible.
Before Using the Power Paddle at a Lockbox
Before you can use the power paddle at a lockbox, you need a time stamp file on your SentriCard®. This
allows the power paddle to set the internal lockbox clock, while providing temporary power to the
lockbox. You need to contact SentriLock Support for a time stamp file. Before you contact SentriLock
Support, you need:
1. The serial number of the lockbox.
2. A computer with a SentriCard® reader and an active Internet connection.
When you are ready, you can reach SentriLock Support at 877-736-8745.
Before you can use the power paddle at the lockbox, it is important to make sure the power paddle is
working properly. To do this, follow these steps:
1. Slide the POWER switch to the ON position.
2. The green POWER light should illuminate. If this light does not illuminate, replace the 9 volt
battery in the power paddle.
Note: The battery compartment is located on the back of the power paddle.
Phone: 877-736-8745 • Fax: 513-618-5801
www.sentrilock.com
2710 East Kemper Road • Cincinnati OH 45241
Before using the power paddle at a lockbox, make sure you have the following items:
•
•
•
•
•
•
The power paddle
Your valid SentriCard® (SentriCard® cannot be expired)
2, new CR123A batteries
A Phillips head screw driver
These instructions on how to use the power paddle
Instructions on how to replace the batteries in an NXT/NXT Wireless lockbox (these instructions
can be found at https://lockbox.sentrilock.com/manuals/faq/default.htm in the topic entitled
Replace the Battery in an NXT/NXT Wireless (Blue) Lockbox)within the Using Your Lockbox
section)
How to Use the Power Paddle
Listed below are the steps to use the power paddle at a lockbox:
1. Insert the power paddle into the lockbox card slot.
Note: Do not remove the power paddle from the lockbox. It must
remain inserted into the lockbox card slot until the end of the
procedure.
2. Slide the Power switch on the power paddle to the ON
position. The green POWER light will illuminate.
Note: If the green POWER light does not illuminate, you
may need to replace the 9 volt battery inside the power
paddle. The battery compartment is located on the back
of the power paddle.
3. Once the power paddle is turned on, the red Status A light will illuminate for approximately one
minute. During this time, the power paddle is charging the lockbox.
4. When the power paddle finishes charging the lockbox, the yellow Status B light will illuminate.
5. Once the yellow Status B light has illuminated, insert your
SentriCard® into the card slot on the left side of the power
paddle. The SentriCard® must be inserted face up with the
gold chip going in first.
Phone: 877-736-8745 • Fax: 513-618-5801
www.sentrilock.com
2710 East Kemper Road • Cincinnati OH 45241
The steps to use the power paddle at an NXT series lockbox and an NXT Wireless series lockbox are
different. Please follow the steps according to which lockbox you are using the power paddle on. To
determine what type of NXT lockbox you are using the power paddle on, refer to the front, left side of
the lockbox. If you find a Wireless sticker here, you are using an NXT Wireless lockbox. If the sticker is
not there, you are not using an NXT Wireless lockbox.
NXT Lockbox:
6.
7.
8.
9.
10.
11.
12.
13.
The lockbox will illuminate the CARD and CODE lights.
Wait for the green Status C light to illuminate on the power paddle.
Enter your PIN + ENT on the lockbox keypad.
The lockbox will display the green READY light.
Press FUNC + 3 + ENT on the lockbox keypad.
The lockbox will open the key compartment, allowing access to the battery compartment.
After the key compartment opens, remove the power paddle from the lockbox.
Slide the POWER switch on the power paddle to the OFF position.
NXT Wireless Lockbox:
6. Press and hold the ENT button on the lockbox keypad for
approximately 2 seconds.
7. Press FUNC + FUNC + 9 + ENT on the lockbox keypad.
8. The lockbox will illuminate the CARD and CODE lights.
9. Wait for the green Status C light to illuminate on the power
paddle.
10. Enter your PIN + ENT into the lockbox keypad.
11. The lockbox will display the green READY light.
12. Press FUNC + 3 +ENT on the lockbox keypad.
13. The lockbox will open the key compartment, allowing access to
the battery compartment.
14. After the key compartment opens, remove the power paddle
from the lockbox.
15. Slide the POWER switch on the power paddle to the OFF
position.
Summary
You can contact SentriLock Support at 877-736-8745. Support is available 7 days a week, from 8AM to
Midnight, EST. SentriLock Support can assist you in using the power paddle and replacing the lockbox
batteries.
Phone: 877-736-8745 • Fax: 513-618-5801
www.sentrilock.com
2710 East Kemper Road • Cincinnati OH 45241