Y2 Series of High-voltage Compact type Three-phase Induction Motors Sample Book
Transcription
Y2 Series of High-voltage Compact type Three-phase Induction Motors Sample Book
Enterprise Standard of Jiamusi Electric Machine Co., Ltd. 0EE.138.177-2007 Y2 Series of High-voltage Compact type Three-phase Induction Motors Sample Book Promulgated on December 31, 2007 Effective as of January 1, 2008 Issued by Jiamusi Electric Machine Co., Ltd. 0EE.138.176-2007 Y2 series of High-voltage Compact type Three-phase Induction Motor Sample Book ⅠGeneral The motors are mainly used in the areas of explosive gas atmosphere, for example: petroleum, chemical industry, coal, power plant, metallurgy, traffic, spinning and weaving, medicine, grain processing, etc. or so of general-purpose machine, such as fan, water pump, compressor, crusher, trimming machine tool, transport machinery etc., or other similar mechanical equipments. ⅡSelection guide 1 Meaning of motor type Y 2 400 1 —2 W Induction motor Outdoors(symbol of protection type) Design no. Shaft height No. of poles The core length symbol for the same frame 2. The type of series motor 2.1 The capacity of Y2 series high-voltage compact type three-phase induction motors(3kV、 6kV)see Table1 Table 1 Synchronous speed Frame size 3000 1500 r/min 1000 750 Power kW 355 400 450 500 1 185 185 — — 2 200 200 — — 3 220 220 160 — 4 250 250 185 — 5 280 280 200 — 1 315 315 220 160 2 355 355 250 185 3 400 400 280 200 4 450 450 315 220 1 500 500 355 250 2 560 560 400 280 3 630 630 450 315 4 710 710 500 355 1 800 800 560 400 2 900 900 630 450 3 1000 1000 710 500 4 1120 1120 800 560 1 0EE.138.176-2007 Table 1(continue) Synchronous speed r/min Frame size 3000 1500 1000 750 Power kW 560 1 1250 1250 900 630 2 1400 1400 1000 710 3 1600 1600 1120 800 4 — — 1250 900 The capacity of Y2 series high-voltage compact type three-phase induction motors (10kV)see Table2 Table 2 Synchronous speed r/min Frame size 3000 1500 1000 750 Power kW 2.2 450 500 560 3. 1 220 220 — — 2 250 250 — — 3 280 280 — — 4 315 315 220 — 5 355 355 250 — 6 400 400 280 220 7 450 450 315 250 8 500 500 355 280 1 560 560 400 — 2 630 630 450 315 3 710 710 500 355 4 800 800 560 400 5 900 900 630 450 1 1000 1000 710 500 2 1120 1120 800 560 3 1250 1250 900 630 4 1400 1400 1000 710 5 - - 1120 800 Voltage class and frequency The motor rated voltage contain 3kV, 6kV and 10kV three kinds of voltage according to the user different geographic position, corresponding rated frequency of power supply is 50Hz. The motor also can be made into other voltage class or frequency on request of the user. All the technical data in this sample book is under the frequency of 50Hz. 2 0EE.138.176-2007 4. Insulation class and temperature rise limit value The insulation class of the motor usually uses F class of insulation. The temperature rise limit value of the motor which winding indirect cooled by air: On the basis of motor operating site altitude above sea level not exceed 1000m and max. ambient temperature not exceed 40℃, the temperature rise limit value of class B insulation is 80K, and 105K for F class of insulation. 5. Bearing construction type and temperature limit value The motors are provided with rolling bearings and sleeve bearings, which construction type of bearing can be decided according to overall and mounting dimensions data sheet, normal product with sleeve bearing construction use forced lubrication, but also can be made into self-lubrication according to request; the motor rolling bearing permitted temperature shall not exceed 95℃, the permitted temperature for sleeve bearing with forced lubrication shall not exceed 80℃ and for sleeve bearing with self lubrication not exceed 95℃. 6. Degree of protection Degree of protection by enclosure of motor is IP44, IP54 and IP55 according to the different operating conditions of the motor, the meaning explanation of the feature as follows: The marking of protection degree is composed of expression letters (“IP”) and two suffixal expression numbers, the first number means each degree of the first kind of protection and the second number means each degree of the second kind of protection. IP 5 4 The second expression number:represents the protection degree of harmful influence caused by water entering into enclosure(water-proof degree) The first expression number:represents the protection degree of people to enclosure and to internal parts in enclosure(dust-proof degree) Expression letters Brief introduction of the meaning of expression number“4”and“5”in degree of protection: The first expression number“4”means the motor can prevent the solid body more than 1mm from entering into it; The first expression number “5” means the enclosure can prevent from touching or closing the charged or rotating parts in it, the enclosure can’t completely prevent dust 3 0EE.138.176-2007 from entering into it, but the quantity of the entering dust isn’t enough to affect the normal operation of the motor. The second expression number“4”means the harmful influence should not be caused when the motor bears the splash from any direction (splash-proof motor). The second expression number“5”means the harmful influence should not be caused when the motor bears the spray from any direction (spray-proof motor). For detail knowledge related to degree of protection see GB4942.1. 7. Cooling method The marking of cooling method is composed of symbol letters “IC” and following numbers, “IC” is abbreviation of English word “International Cooling”. The cooling method of Y2 series of high-voltage compact type three-phase induction motors is IC411, the meaning of letters and numbers as follows: IC 4 1 1 `Symbol letters Arrangement of cooling circuit Driving method of primary coolant motion Driving method of secondary coolant motion Arrangement of cooling circuit:4 represents cooling at surface of frame Coolant motion driving method: 1 represents self-circulation: cooling medium motion related to motor rotating speed, usually by fan mounted on the rotor. Coolant: divided into primary coolant and secondary coolant, coolant usually use air (A) and water (W), etc. Primary coolant: a medium, liquid or gas, which, being at a lower temperature than a part of a machine and in contact with it, removes heat from that part. Second coolant: a medium, liquid or gas, which, being at a lower temperature than the primary coolant, removes the heat given up by this primary coolant by means of a heat exchanger or through the external surface of the machine. 8. Weather-protected type and operation environment conditions 1)Weather-proof types are: a. Damp and tropical climate type, indoor (TH); outdoor (THW); b. Dry and tropical climate type, indoor (TA); outdoor (TAW); c. Tropical climate type, indoor (T); outdoor (TW) d. Outdoor light corrosion-proof type (W) e. Outdoor middle corrosion-proof type (WF1) 4 0EE.138.176-2007 f. Outdoor strong corrosion-proof type (WF2) g. Indoor middle corrosion-proof type (F1) h. Indoor strong corrosion-proof type (F2) The protection type mentioned above shall be marked at the end of motor type, for example: Y2 5001-4WF1. 2)The operating environmental conditions of each whether-proof type motor under different locations are as follows: a. Operating environment conditions include: climatic conditions (K), special climate conditions (Zh-thermal radiation, Za-surrounding air movement, Zw- water source other than rainfall), biotic conditions (B), chemical active material conditions(C), mechanical active material conditions(S) and mechanical conditions (M) altogether six categories. b. Operating location of the motor can be divided into: Weather protected location: Indoors or have good shield location (the structure construction can prevent or reduce the influence of outdoor climate daily change, include shed condition), the number ahead of environment condition class is “3”, simplified as indoor condition. Non weather protected location: Locations completely in the open air or only has simple cover (can hardly prevent the influence of outdoor climate daily change), the number ahead of environment condition class is “4”. 9. Connection method Connection method of all the high-voltage motor is Y connection. 10. Cable entry In normal condition the motor is provided with rubber sleeve cable entries, and also can provide steel tube connection units or armoured cable fittings according to the user’s request. 11. Duty Duty type of motor is continuous (S1). 12. Performance index allowance Efficiency η:-10%(1-η) Power factor cos φ:-(1-cosφ)/6 Min. absolute value 0.02 Max. absolute value 0.07 Locked-rotor current:+20% of current guaranteed value 5 0EE.138.176-2007 Locked-rotor torque:+25%/-15% of torque guaranteed value (the value of +25% may be exceeded through negotiation ) Min. torque:-15% of torque guaranteed value Max. torque:-10% of torque guaranteed value Ⅲ Operation conditions of motor in site 1. Altitude above sea level of the motor normal operating locations is up to 1000m. 2. The max. ambient air temperature shall not exceed +40℃. 3. The min. ambient air temperature should not be lower than -20℃, the min. ambient air temperature of sleeve bearing motors should not be lower than 0℃. 4.Voltage and frequency allowance value: The motor can continuously operate at area A( voltage deviation is –5%~+5% of rated value, frequency deviation is –2%~+2% of rated value) and reach its basic performance, but the performance in this range differs from that at rated voltage and frequency( see rated point in Fig.1), such as, the temperature rise of motor can be higher than that at rated voltage and frequency. If the motor operate at the border A, the temperature rise can be higher 10℃ than that at rated point. The motor can operate at area B( voltage deviation is –10%~+10% of rated value, frequency deviation is –5%~+3% of rated value) and reach its basic performance, but the performance difference between at point of this area and rated voltage and frequency should be higher than that between at point of area A and rated voltage and frequency, the temperature rise of motor can be higher than that at rated voltage and frequency and can be higher than that at area A. The motor should not continuously operate at the border B. Other electric operation condition of motor should be in accordance with GB755. Fig.1 Limits of voltage and frequency of motor 6 0EE.138.176-2007 Ⅳ Construction features Y2 Series of High-Voltage Compact type Three-phase Induction Motor is the latest-generation motor with high efficiency, energy saving and environmental protecting advantages. It is designed and manufactured on the basis of experiences of years of manufacturing motors, through the analysis of construction field, electromagnetic field, fluid field and compound field by large finite element analysis, and through the principle of double circulated cooling and ventilating system. This series of motors have advantages of small volume, light weight, compact conformation, good appearance and smooth lines etc. 1. Cooling air path, frame and end shield Y2 series of motors has two independent cooling air paths: internal cooling air path and external cooling air path (see Fig.2), most of the loss heat transmit from stator core to motor frame, and then bring away by external cooling air, the rest loss heat transmit to motor frame through internal cooling circuit and take away by external cooling air. Fig. 2 The motor frame use quadrature distributed total cooling fin casting frame, between cooling fins use nonisometric distribution and discentric circle combination method, 4 axial air duct are provided at 45°direction. Because of the motor frame has reduced scale, outer cooling air from non-driving end can reach to driving end more effectively through cooling fins, so as to achieve the best cooling effect. The terminal box is located at upper motor side where air duct has placed in order to not influence heat dissipation and the flowing of cooling air. The frame inner surface around stator winding end provided with heat absorption rib. Frame enough large area of dissipation with rib type construction guaranteed powerful heat sinking ability. Two lifting rings are opposite angle mounted on the air duct (the angle of lifting rings can be random adjusted) to make the motor hoisting more convenient. The end shield of driving end and non-driving end has the same structure; heat sinking rib is provided for inner and outer of end shield to enhance the end shield stiffness and heat 7 0EE.138.176-2007 sinking ability. High strength casting iron motor frame and end shield ensured the motor has high stability. 2 Low noise fan On the precondition of the cooling effect has been satisfied, the fan and fan cover use streamline design construction, so as to improve fan efficiency and reduce fan noise. External fan: 2 poles: propeller type axial fans (unidirectional rotation); shaft height H355-H400, 4 poles and above motor use convex centrifugal fan and can be bidirectional rotated. H450 and above, 4 poles motor use backward tilting type centrifugal fan, only suitable for one direction of rotation; motors with other poles use convex centrifugal fan and suitable for both directions. Internal fan: Radial centrifugal fan (can be bidirectional rotated). 3 Stator The motor has a laminated core first compressed and secured before it is fitted into the frame and then pressed into the machined frame.The stator windings are class F insulated, anticorona treatment(10kV),the ends of windings are boneded and fixed firmly, and the windings are vacuum pressure impregnated with solventless varnish. Therefore, the motors have good and reliable insulating performance, higher mechanical strength, long service life,as well as higher moisture-resistance, corrosion resistance and anticorona ability. 4 Rotor The further aim of this series of motors is cast aluminum rotor technology, which has already proved to be successful in millions of low-voltage and high-voltage motors and then popularized to large capacity motor. The rotor busbar and short circuit ring casting into an integral part. This technology ensured the solidity of the structure and the unique stability of the cast rotor. Use centrifugal cast aluminum technique pouring the liquid state aluminum into rotor lamination core slot, the mould is pouring at one shot, the short circuit ring and the busbar are pouring at the same time. 5 Bearing There are two kinds of bearings: rolling bearings and sleeve bearings. Usually the motor use rolling bearings, sleeve bearings are used for motors which the service conditions (depending on rotating speed, load and operating conditions) exceed the limit value. The DE and NDE bearings for standard designed motor H500-2 (3kV、6kV、10kV) and H560-2(3kV、6kV、10kV)are end-shield type spherical sleeve bearings, forced lubrication and the insulation treatment is provided for NDE. Permit axial play at free state is ±5mm, in this case the motor rotor and shaft system must be axial located by “caging device” on driven 8 0EE.138.176-2007 equipment. H500-2(10kV) also has rolling bearings; other motors use rolling bearings and have oil inlet and outlet device(without shutdown the motor), can fill up the lubrication grease and discharge the waste grease during motor operation. 6 Terminal box According to the different explosion-proof requirement, the terminal box for main power supply is increased-safety type steel plate tension terminal box, and has the advantage of beautiful appearance, lower weight, suitable for motors with 3kV, 6kV and 10kV voltage, and high generalization degree. Standard designed motor have two terminal boxes, namely main terminal box and auxiliary terminal box. The main terminal box can be mounted at four different positions on motor frame ventilating slot in order to meet the different connection requirement at site. If there is no special requirement, the main terminal box should located at DE right upper side (viewed from motor shaft extension end), cable inlet from bottom. The auxiliary terminal box is located at NDE right upper side (viewed from motor shaft extension end), cable inlet from bottom. 7 Monitoring and protection Standard designed motors provided with these monitoring and protection devices: stator winding temperature detector platinum resistance PT100, bearing temperature detector platinum resistance PT100 and anti-condensation space heater. All the connecting wire of temperature detector and heater are connected into the connecting terminals of auxiliary terminal box. Ⅴ Performance data: 1 For the data sheet of Y2(6kV)series of high-voltage compact type three-phase induction motors, see table 3(calculated value) 9 0EE.138.176-2007 Table 3 Type Rated Rated Rated Efficie Power power current torque ncy factor (kW) (A) (r/min) (%) cosΦ Max. torque Rated torque Locked- Locked- rotor rotor torque current Motor Permissib Rated Rated Jm le load J torque current (kg.m2) (kg.m2) Moment of inertia Weight (kg) Y2 3551-2 185 20.9 94.8 2.0 13.6 2035 Y2 3552-2 200 22.5 95.1 2.5 14.8 2080 Y2 3553-2 220 24.7 95.4 2.4 16.2 2155 Y2 3554-2 250 28.0 95.6 2.5 19.1 2195 0.90 Y2 3555-2 280 31.3 95.8 2.8 21.6 2240 Y2 4001-2 315 35.2 95.8 4.3 21 2730 Y2 4002-2 355 39.6 95.9 4.5 24 2810 Y2 4003-2 400 44.5 96.0 4.9 29 2925 Y2 4004-2 450 50.0 96.2 5.3 32 3015 Y2 4501-2 500 54.9 6 43 3475 Y2 4502-2 560 61.5 6.2 50 3610 Y2 4503-2 630 69.2 6.8 58 3770 7.5 64 3910 15 85 5725 16 92 5855 2985 96.3 0.7 96.3 7.0 96.3 Y2 4504-2 710 77.8 96.5 Y2 5001-2 800 87.7 96.5 Y2 5002-2 900 98.6 96.5 Y2 5003-2 1000 109.5 96.6 17 103 5990 Y2 5004-2 1120 122.3 96.8 19 107 6230 Y2 5601-2 1250 136.4 96.9 28 119 7475 Y2 5602-2 1400 151.1 96.9 30 135 7765 Y2 5603-2 1600 172.5 97.0 32 165 8085 Y2 3551-4 185 22.1 94.6 4.8 89 2175 Y2 3552-4 200 23.9 94.8 5.4 95 2250 Y2 3553-4 220 26.2 95.0 5.8 105 2310 Y2 3554-4 250 29.7 95.2 Y2 3555-4 280 33.2 95.5 Y2 4001-4 315 37.3 Y2 4002-4 355 Y2 4003-4 Y2 4004-4 0.91 0.92 2.0 6.1 112 3345 6.4 138 2385 95.6 8.0 150 2935 41.9 95.9 8.5 170 3035 400 47.1 96.1 9.3 200 3120 450 52.3 9.8 220 3190 Y2 4501-4 500 58.1 13 240 3850 Y2 4502-4 560 65.1 96.3 15 260 4045 Y2 4503-4 630 73.1 96.4 16 290 4310 Y2 4504-4 710 81.3 96.6 18 320 4550 Y2 5001-4 800 91.5 96.7 33 330 5540 Y2 5002-4 900 102.9 96.7 35 380 5730 Y2 5003-4 1000 114.3 96.8 37 440 5845 Y2 5004-4 1120 127.9 96.9 39 510 5970 Y2 5601-4 1250 142.7 96.9 63 750 7575 1488 0.85 96.2 96.3 0.8 0.86 0.87 6.5 10 0EE.138.176-2007 Table 3 (continue) Type Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Y2 Rated Stator Rated Efficie Power power current torque ncy factor (kW) (A) (r/min) (%) cosΦ 5602-4 5603-4 3553-6 3554-6 3555-6 4001-6 4002-6 4003-6 4004-6 4501-6 4502-6 4503-6 4504-6 5001-6 5002-6 5003-6 5004-6 5601-6 5602-6 5603-6 5604-6 4001-8 4002-8 4003-8 4004-8 4501-8 4502-8 4503-8 4504-8 5001-8 1400 1600 160 185 200 220 250 280 315 355 400 450 500 560 630 710 800 900 1000 1120 1250 160 185 200 220 250 280 315 355 400 156.1 178.0 20.1 23.2 25.1 27.2 30.4 34.0 38.2 43.0 48.5 54.5 60.4 67.6 75.9 85.4 96.1 106.7 118.5 132.4 147.6 21.6 24.9 26.5 29.1 32.6 36.4 40.9 46.1 50.5 Y2 5002-8 450 56.6 95.6 Y2 Y2 Y2 Y2 Y2 Y2 500 560 630 710 800 900 62.8 70.3 78.0 88.0 98.9 111.1 95.7 95.8 95.9 95.9 96.1 96.2 5003-8 5004-8 5601-8 5602-8 5603-8 5604-8 1488 987 742 97.0 97.2 94.4 94.6 94.8 94.9 95.4 95.5 95.7 95.7 95.7 95.8 96.0 96.1 96.2 96.4 96.5 96.6 96.7 96.9 97.0 93.9 94.1 94.3 94.5 94.7 94.8 95.0 95.1 95.3 Max. torque Rated torque Locked- Locked- rotor rotor torque current Rated Rated torque current 0.89 0.81 6.5 0.82 0.83 6.0 0.84 2.0 0.8 0.76 0.77 0.78 5.5 0.80 0.81 Moment of inertia Motor Jm (kg.m2) Permissible load J Weight (kg) (kg.m2) 68 76 6.5 7.0 7.8 11.8 12.5 13.3 14.3 16 18 20 22 44 46 48 51 97 101 106 113 12.5 13.0 14.0 15.3 16 18 20 22 44 810 910 202 235 254 270 306 340 390 420 490 550 620 910 1020 1150 1310 1116 1265 1411 1586 390 450 490 540 600 630 660 690 590 7885 8245 2330 2395 2480 2950 3000 3110 3220 3960 4170 4370 4570 5725 5845 6120 6300 7350 7620 7840 8095 2930 2975 3085 3205 3955 4155 4355 4560 5720 46 650 5840 48 51 120 128 134 710 790 1390 1571 1780 6110 6290 6860 7145 7370 140 2017 7610 2 For the data sheet of Y2 (10kV)series of high-voltage compact type three-phase induction motors, see table 4(calculated value). 11 0EE.138.176-2007 Table 4 Type Rated Rated Rated Efficie Power power current torque ncy factor (kW) (A) (r/min) (%) cosΦ Max. torque Rated torque Locked- Locked- rotor rotor torque current Motor Permissible Rated Rated Jm load J torque current (kg.m) (kg.m2) 5.6 14 2875 6.5 15 3015 Moment of inertia Weight (kg) Y2 4501-2 220 16.0 94.6 Y2 4502-2 250 18.1 94.7 Y2 4503-2 280 19.8 94.9 7.4 18 3155 Y2 4504-2 315 22.2 95.1 8.6 21 3315 Y2 4505-2 355 25.0 95.2 9.1 26 3400 Y2 4506-2 400 28.1 95.5 9.7 31 3480 Y2 4507-2 450 31.6 95.6 10.2 36 3525 Y2 4508-2 500 34.7 10.8 41 3615 Y2 5001-2 560 38.8 12 60 4970 Y2 5002-2 630 43.6 14 70 5090 Y2 5003-2 710 49.0 96.0 15 85 5220 Y2 5004-2 800 54.6 96.1 16 92 5330 Y2 5005-2 900 61.4 96.2 17 103 5460 Y2 5601-2 1000 68.1 96.3 19 94 6860 Y2 5602-2 1120 75.3 96.4 28 98 7160 Y2 5603-2 1250 83.9 96.5 30 111 7495 Y2 5604-2 1400 93.9 96.6 32 126 7795 Y2 4501-4 220 16.0 94.6 12.9 105 3025 Y2 4502-4 250 18.1 94.7 Y2 4503-4 280 20.3 94.9 Y2 4504-4 315 22.5 95.1 Y2 4505-4 355 25.3 95.2 Y2 4506-4 400 28.5 95.5 0.84 0.86 95.7 2985 95.8 95.9 Y2 4507-4 450 32.0 95.6 Y2 4508-4 500 35.1 95.7 Y2 5001-4 560 39.2 Y2 5002-4 630 44.1 95.9 Y2 5003-4 710 49.6 96.0 Y2 5004-4 800 55.2 96.1 Y2 5005-4 900 62.1 96.2 Y2 5601-4 1000 68.9 96.3 Y2 5602-4 1120 76.2 96.4 Y2 5603-4 1250 85.0 96.5 Y2 5604-4 1400 95.1 Y2 4504-6 220 16.4 Y2 4505-6 250 Y2 4506-6 Y2 4507-6 1488 95.8 0.7 0.87 7.0 0.88 0.89 0.84 2.0 0.85 0.8 6.5 0.86 14.8 120 3150 16.9 135 3305 19.2 150 3455 20.3 163 3525 21.6 175 3570 22.5 188 3645 23.6 200 3730 31 290 5045 33 330 5205 35 380 5305 37 440 5450 39 510 5565 58 617 6725 63 692 7020 68 775 7315 96.6 76 868 7710 94.2 27.4 225 3500 18.7 94.3 28.8 238 3565 280 20.9 94.5 30.2 252 3645 315 23.4 94.7 33.0 264 3795 Y2 4508-6 355 26.3 34.9 280 3900 Y2 5001-6 400 29.6 95.0 43 510 5090 Y2 5002-6 450 32.9 95.1 44 590 5240 Y2 5003-6 500 36.5 95.2 46 650 987 0.87 0.88 0.7 0.82 0.8 94.9 0.83 6.0 5350 12 0EE.138.176-2007 Table 4(continue) Type Rated Rated Rated Efficie Power power current torque ncy factor (kW) (A) (r/min) (%) cosΦ Y2 5004-6 560 40.8 95.5 Y2 5005-6 630 45.8 95.6 Y2 5601-6 710 51.6 95.7 Y2 5602-6 800 58.1 95.8 Y2 5603-6 900 64.4 Y2 5604-6 1000 71.5 96.1 Y2 5605-6 1120 80.0 96.2 Y2 4506-8 220 17.5 94.1 Y2 4507-8 250 19.6 94.2 Y2 4508-8 280 22.0 94.3 Y2 5002-8 315 24.7 94.4 Y2 5003-8 355 27.8 94.6 Y2 5004-8 400 30.9 94.7 Y2 5005-8 450 34.7 Y2 5601-8 500 38.5 95.0 Y2 5602-8 560 42.5 95.1 987 Max. torque Rated torque 94.8 Y2 5603-8 630 47.7 95.3 Y2 5604-8 710 53.0 95.5 Y2 5605-8 800 59.6 95.6 Locked- rotor rotor torque current Rated Rated torque current 0.8 0.83 6.0 0.7 96.0 742 Locked- 0.84 0.77 0.78 2.0 0.8 5.5 0.79 0.80 0.81 0.7 Moment of inertia Motor Jm (kg.m) Permissible load J Weight (kg) (kg.m2) 48 710 5495 51 790 5635 93 984 6950 97 1116 7220 101 1265 7495 106 1411 7740 113 1586 8010 30 394 3635 33 406 3770 35 419 3890 43 820 5150 44 870 5295 46 950 5405 48 1010 5575 113 1236 6525 120 1390 6760 128 1571 7005 134 1780 7230 140 2017 7470 13 0EE.138.177.2007 Ⅵ、Overall and mounting dimensions drawing 1、Overall and mounting dimensions for Y2 (3kV、6kV)series of high-voltage compact type three-phase induction motors Mounting dimension and tolerance No. Frame of size poles 355 400 2 4-6 2 A B Basic dim. Basic dim. 630 710 C D E F Basic dimension Basic dim. dim. dev. dim. dev. dim. 75 +0.030 +0.011' 140 ±0.50 20 210 ±0.57 28 dev. 900 254 100 85 1000 4-8 280 2 450 4 800 1120 6-8 425 2 * 500 4 900 1250 315 6-8 530 2 * 560 4 1000 1400 355 6-8 Dimension Basic dimension Basic ±4.0 110 95 120 130 110 130 140 130 150 160 170 +0.035 +0.013 +0.040 +0.015 +0.035 +0.013 210 170 210 250 210 22 ±0.50 ±0.57 +0.040 +0.015 250 300 ±0.65 Overall dimension (limited value) G Dimension dev. H dimen Dimens Basic dim. sion Basic dim. ion dev. dev. 67.5 355 90 0 -0.052 28 25 32 0 -0.062 28 32 36 32 36 40 0 -0.052 0 -0.062 K 76 100 86 109 119 100 119 128 119 138 147 Basic dim. dimens ion AB AC AD AG BA BB BC BD 28 790 750 780 730 240 1110 217 112 160 870 840 830 745 240 1200 200 115 950 910 855 790 240 1340 165 136 35 -0.2 450 +0.62 0 0 -1.0 500 0 -0.3 0 -0.2 200 1080 1035 910 820 300 1490 264 114 42 560 GD H A HB HD L dev. 400 0 -0.3 AA 210 1170 1185 955 870 300 1680 178 170 14 16 14 16 14 18 16 18 20 18 20 22 210 1010 50 335 1110 1770 1840 1900 2000 2070 50 370 1170 2150 2250 2580 50 490 1290 2380 2485 2900 60 595 1400 2600 2775 * In order to select the motor size of sleeve bearing, the axial play can be defined by manufacturer and client. 12 0EE.138.177.2007 2、Overall and mounting dimensions for Y2(10KV)series of high-voltage compact type three-phase induction motors Mounting dimension and tolerance Frame size 450 500 560 No. of poles Ca A B Basic Basic Basic dim. dim. dim. D dimens ion dev. 2 4 800 1120 280 6-8 315 2 ±4.0 4 900 1250 315 6-8 2 530* 4 1000 1400 355 6-8 Basic dim. E Dimens ion dev. 95 +0.035 +0.013 120 130 +0.040 +0.015 100 +0.035 +0.013 Basic dimensio dim. Overall dimension (limited value) F n dev. 170 ±0.50 210 250 210 ±0.57 130 140 250 +0.040 130 +0.015 150 300 ±0.65 160 Basic dim. G Dimensio Basic dimensio Basic n dev. 25 0 -0.052 32 0 -0.062 28 0 -0.052 32 36 32 36 40 H 0 -0.062 dim. 86 109 119 90 119 128 119 138 147 n dev. dim. K Dimens ion dev. 450 Basic dim. dimen sion AA AB AC AD AG BA BB BC BD 500 0 -0.3 0 -0.2 0 -0.3 35 160 950 910 855 805 240 1340 165 +0.62 0 200 1080 1031 910 835 42 560 HA HB HD L 14 2070 50 385 1170 2150 2250 dev. 136 0 -0.2 0 -1.0 GD 1490 264 114 1680 178 170 300 210 1170 1185 955 890 18 16 2580 18 20 18 20 22 50 490 1290 2380 2480 2900 60 595 1400 2600 2775 * In order to select the motor size of sleeve bearing, the axial play can be defined by manufacturer and client. 13 0EE.138.177.2007 Ⅶ The interface dimensions of site mounting of motor 1 In the main power supply there are three M16 connection terminals,the following diagram is overall dimension drawing (6kV、10kV)of the terminal box: 2 The stator temperature detector, bearing temperature detector and heater are share one overall dimensions drawing of auxiliary terminal box 3 Inner diameter of rubber sealing ring for the incoming line of the main power supply is shown in the following diagram. The threaded interface also can be supplied,and the dimension of which is G3. The stator temperature detector, bearing temperature detector and heater are share one auxiliary terminal box, there are three interface. For the inner diameter of seal ring of cable entry, see above diagram. The threaded interface also can be supplied, and the dimension of which is M24×2. 14 0EE.138.177.2007 4 The wiring diagram of terminal box for main power supply, stator temperature detector, bearing temperature detector and heater see following diagram: Ⅷ Ordering information 1. When selecting three-phase induction motors, the following matters must be taken into account: a. Operating environment, ambient temperature, altitude, etc. b.Mechanical characteristic and moment of inertia for the driven device. c. Starting method, starting frequency and starting voltage drop d.Direction of rotation of motor e. The mechenical connetion method and requirement between motor and driven load f. The position of terminal box. g.Duty type and other special requirement 2. Motors supplied in the Sample book are standard motor design a. The altitude for standard motor is not more than 1000m b. The max. ambient temperature is not more than 40℃,and the min. is not lower than -20℃, for motor of sleeve bearing or air-to-water cooling, the min. ambient temperature is not lower than 0℃. c. Direct on line and full voltage starting d. CW. rotated for standard motors (as viewed from DE) e. the main and auxiliary terminal boxes are on the right side of motor ( as viewed from DE) f. For the standard designed motors of sleeve bearings, normally provided with forced lubrication and no pressure oil return. 15 0EE.138.177.2007 3. Normal ordering The order without special requirements is normal order, the following parameters should be noted when ordering.(eg.) Type :Y2 5001-2 Rated voltage:6kV Rated frequency: 50Hz Rated power:800kW No. of poles:2 Rated speed:2985r/min Mounting arrangement: B3 Duty type: S1 Method of cooling: IC411 Degree of protection: IP54 Direction of rotation :CW. Operating environment: indoors Method of incoming line: rubber sleeve 4. Order with additional requirements If there’s one or more requirements for the following items, it should be declared in ordering. 4.1 The voltage are not 3000、6000 and 10000V,eg.:3.3kV、6.3kV; 4.2 Frequency is 60Hz; 4.3 Power is not the standard value in data sheet, or coincidence relations between power and mounting demension are different from data sheet. 4.4 The altitude above sea level is more than 1000m. 4.5 Ambient temperature:more than 40℃, or the lowest temperature is less than -20℃. 4.6 Low noise: the noise is lower than the specification of GB10069 4.7Non-standard mounting arrangement: corrsponding relations between frame size and mounting arrangement are different from data sheet. 4.8 The special environment needing declaring,for example: humid tropics, outdoors, corrosion, salt spray, mold, dust and blown sand, etc., for corrosion, it must be listed for taking corresponding measures according to the corrosiveness. 4.9 The direction of rotation of motor is CCW. 4.10 The special requirement for electric performance, eg: high locked-rotor torque, high slip, high moment of inertia and low locked-rotor current, etc. 4.11 Other special requirements, eg.: protective relay device ( temperature monitoring device for winding and bearing, differential protection), special bearing, special packing and spare parts ahead of specification,etc. 4.12 If there’s above special requirements and other requirements, please negotiate with our technical department or sign technical agreement. 4.13 With technical development of products and revisal of relevant standards at home and aboard, technical data shown herein are subject to change without notice. 16