CT1/CS Series INSTRUCTION MANUAL 5. Connection to counters

Transcription

CT1/CS Series INSTRUCTION MANUAL 5. Connection to counters
CT1/CS Series INSTRUCTION MANUAL
CT1/CS Series INSTRUCTION MANUAL
Customer Service
5. Connection to counters
Model : CT1 · CS
37-7 Chuo-cho, 2-Chome
Meguro-ku, Tokyo 152-0001 Japan
Tel: +81-3-37165151
Fax: +81-3-37104552
[email protected]
http://www.lineseiki.com
AC power
source
Model : CT1-R (4P connector)
Terminal numbers in
generator's connector
A Output
B GND
C DC power source
Model : CT1
1. Models
Reed switch
500meter [yard]/minute
Weight
700g [25oz.]
710g [25oz.]
730g [26oz.]
730g [26oz.]
740g [26oz.]
790g [28oz.]
740g [26oz.]
740g [26oz.]
750g [26oz.]
780g [28oz.]
Torque
Model : CT1-R
CT1-3:1R
CT1-3:10R
CT1-3:100R
D
COM
Bidirectional
Electronic Counter
C
Output A
Output B
100[3.94]
±10[±0.39]
47[1.85]
4-
±0.5[±0.02]
5[0.20]
57[2.24]
130[5.12]
Mounting Holes 25[0.98]
95[3.74]±0.5[±0.02]
105[4.13]
Model : CT1-A
85.5[3.37]
7[0.28]
N.O
COM
B
A Output
B GND
C DC Power Source
A
B
C
D
A
C
B
DC Power Source
Output A
GND
Output B
61[2.40]
5[0.20]
Model : CS
B
CT1-A
68[2.68]
39[1.54]
]
30
[0.
7.5
Exploded view
4P connector
D
A
C
B
COM
GND
D
C
CT1-R
A
B
Meter Wheel
Wheel
UNIT OF
MEASURE
38[1.50]
A
A
B
N.O
Make sure that measuring wheels are fixed to shaft of the
device with screws for avoiding slip.
Make sure that measuring wheels are fixed with parallel and
horizontal to measuring object or roller.
In the case measuring object is possible to be stretched by
tension, temperature and humidity, be careful with the
surrounding condition when measuring.
There may be some differences between measured value on
the counter and actual length of the material. In the case,
please confirm if measuring wheel slips or measuring roller
does not synchronize with measuring object.
ON and OFF ratio of output of standard device is 1:1.
For example, 0.5m-ON and 0.5m-OFF are for the measuring unit
of a meter.
There may be some differences between measured value on
the counter and actual length of the material. The difference
may be created by the measuring "Start position" or the
measuring "stop position" to be made shortly after or before
ON/OFF of output has been made.
In the case, it is recommended that you consider if the
measuring unit is suitable to the measuring condition.
57[2.24]
130[5.12]
25[0.98]
95[3.74]±0.5[±0.02]
105[4.13]
C
18[0.71]
8[0.31]
• Model : CS
(Reed switch output)
D
4-
48[1.89]
A
C
C
B
GND
47[1.85]
320[12.60]+20[+0.79]
3P connector
5-12VDC
Lead
Switch
47[1.85]
3- 6[0.24]
Mounting Hole
±0.5[±0.02]
59[2.32]
134[5.28]
25[0.98]
59[2.32]
110[4.33]
Meter
Wheel
Yard
Wheel
Meters
Yards
MODEL
MRM096 MRM097
TYPE OF
SURFACE
Plain
MATERIAL
OF SURFACE
Thermoplastic
Rubber
Yard Wheel
26[1.02]
18[0.71]
±0.5[±0.02]
Mounting Holes
Exploded view
• Model : CT1-R
(Photoelectronic
sensor 2 outputs)
4P connector
7.5[0.30]
5[0.20]
2 pieces of measuring wheel for meter are equipped as standard
accessories.
Instead of those, 2 pieces of measuring wheel for yard are available.
Please order type of measuring wheel.
"-YP" should be added to the model number. (Ex.) CT1-3:10A-YP
*3P/4P connector (Please wire the cables to the terminal pins inside the plug after removing the cover.)
• Model : CT1-A
(Photoelectronic
sensor 1 output)
3P connector
Output
A Output
Detection
Circuit
B
GND
7.5[0.30]
Measuring wheel for meter : Diameter 106.1mm (Circumstance 1/3 meter), Surface material is Thermoplastic Rubber.
Measuring wheel for yard : Diameter 97.0mm (Circumstance 1/3 yard), Surface material is Thermoplastic Rubber.
4. Connection
Output B
C
2K
Installation note
3. Accessories
Measuring wheel for meter x 2
Measuring wheel for meter x 2, 3P connector x 1
Measuring wheel for meter x 2, 4P connector x 1
Measuring wheel for meter x 2
G10 G11
3
1
4
2
CS-3:1
5-24VDC
Detection
Circuit
30[1.18]
Maximum
load current
1 Output
Reed switch Contact output, Capacity : 300VAC 0.7A 70VA, 350VDC 0.5A 50W (Load)
-5 - +40°C [23 - 104°F] (Should not be Frozen) Ambient Humid. : Operating
85% max. (Non-Condensing)
COM
C
GND
3.9K A
Output A
19[0.75]
Output
impedance
D
CT1-3:1000A
C
5-12VDC
32[1.26]
Current
consumption
CS-3:1
N.O
Detection
Circuit
32[1.26]
Power source
2K B
7[0.28]
1 Output
Microswitch Contact output, Capacity : 250VAC · 5A , 125VDC 0.5A (Load)
1 Output
5-24VDC±10%
35mA
3.9K
100mA
1 Output
5-12VDC±10%
20mA
2K
20mA
2 Outputs( 90°Quadrature)
5-24VDC±10%
70mA
3.9K
100mA
2 Outputs( 90°Quadrature)
5-12VDC±10%
40mA
2K
20mA
-10 - +50°C [14 - 122°F] (Should not be Frozen) Ambient Humid. : Operating
35 - 85% (Non-Condensing)
Over-voltage category II, Pollution degree 2, Indoor use (IEC61010-1) Altitude 2000m max. Compliance
CE, RoHS
• Model : CT1
(Micro Switch output)
2K
85.5[3.37]
5[0.20]
Output
G60 G62
3
1
4
2
Model : CS
CT1-3:1A
CT1-3:10A
CT1-3:100A
Model : CT1
Electronic Counter
Electromagnetic Counter
CT1-3:1,CT1-3:10
CT1-3:1A,CT1-3:10A,CT1-3:100A
CT1-3:1000A
CT1-3:1R,CT1-3:10R,CT1-3:100R
CT1-3:1000R
Ambient temp. : Operating
Installation environment
Model : CT1
Model : CT1-A
Model : CT1-R
Model : CS
A
5-24VDC
Open collector output is available in 1 and 2 non-contact outputs models.
"C" should be added to the model number. (Ex.) CT1-3:10AC
Model
G48 E48
3
1
4
2
7. Dimensions : mm [inch]
2. Specifications
Ambient temp. : Operating
A
3.9K B
Detection
Circuit
Micro
Switch
0.015N m
(153gf-cm)
[2.12ozf-in]
740g [26oz.]
3.9K
N.O
Electronic Counter
0.015N m
[2.12ozf-in]
MDR
3
4
6
5
Model : CT1-A
CT1-3:1000R
Proper Counter
Electronic Counter
Electromagnetic Counter
61[2.40]
* Factory-installed option. :
1m[yard]
Speed
240meter [yard]/minute
24meter [yard]/minute
700meter [yard]/minute
500meter [yard]/minute
250meter [yard]/minute
100meter [yard]/minute
700meter [yard]/minute
500meter [yard]/minute
250meter [yard]/minute
100meter [yard]/minute
G10 G11
1
4
3
30[1.18]
Unit
G60 G62
1
4
3
20[0.79]
Sensor
G48 E48
1
4
3
Terminal numbers in
generator's connector
A
DC power source
B
Output A
C
GND
D Output B
6. Output circuit
CT1-3:1
CT1-3:10
CT1-3:1
1m [yard]
Microswitch
CT1-3:10
0.1m [yard]
CT1-3:1A
1m [yard]
Photoelectronic Sensor,
CT1-3:10A
0.1m [yard]
1 non-contact output
CT1-3:100A
0.01m [yard]
CT1-3:1000A
0.001m [yard]
CT1-3:1R
1m [yard]
Photoelectronic Sensor,
CT1-3:10R
0.1m [yard]
2 non-contact outputs
CT1-3:100R ( 90°Quadrature Output ) 0.01m [yard]
CT1-3:1000R
0.001m [yard]
MD
4
3
2
It is recommendable to use such
components as diode, CR etc., for
the protection of contact in the
case of connection with such
inductive load as electromagnetic
counter.
Terminal numbers in counter
Terminal numbers in counter
• Do not use this device near machines that emit strong electromagnetic fields or objects that store static electricity.
• Do not drop or subject this device to strong impact.
• Do not use this device on rollers with high temperature or where it will be exposed to solvent, oil and water.
• Do not use or store this device where it will be exposed to direct sunlight, dust, high temperature and high humidity.
• Do not use this device where it will be exposed to vibration to avoid incorrect measuring or fault.
• Do not use organic solvents such as thinners etc. to clean this device.
• Do not attempt to disassemble or modify this device.
• Internal parts may be destroyed if a voltage outside the rated voltage is applied.
• Do not touch the conductive part of leadwires while power is being applied.
CS-3:1
DC power
source
Model : CT1-A (3P connector)
Attention
Model
Electromagnetic
Counters
26[1.02]
18[0.71]
7.5[0.3]
Contact :
E-mail :
Web :
Electromagnetic
Counters
7.5[0.3]
97[38.2] +0.3[0.01]
-0
Address:
Misuse of this device may lead to
injury to the user or damage to the
device.
WARNING
LINE SEIKI CO., LTD.
106.1[4.18] +0.3[0.01]
-0
Thank you for your purchasing our product. Please read this instruction
manual carefully before using to ensure the correct usage of this product.
Please keep this instruction manual for future reference.
Rubber Wheels are subject to slip for wear in the long usage.
It will cause measuring discrepancies. Please check the Wheels
sometimes and exchange to new ones.
This manual was last revised Mar. 31, 2014. 4CT001F
*Subject to change without prior notice.
All Rights Reserved,Copyright © 2014,LINE SEIKI CO.,LTD.