Reimpet International Corporation Ingersoll Rand 1500E Land

Reimpet International Corporation Ingersoll Rand 1500E Land

Reimpet International Corporation
Ingersoll Rand 1500E Land Drilling Rig
Technical Specifications
Reimpet International Corporation, 1302 Miles St., Houston, TX 77015
[email protected]
Inventory of Equipment
1. DRAWWORKS: Trailer mounted Ingersoll-Rand Model 2550 Drawworks, rated at 1,500 HP
drilling to 15,000 ft. with 5” Drill Pipe, driven by two (2) GE752 Series wound DC traction
motors. Lebus grooved main drum for 1¼” drill line, complete with an NOV-Baylor Model
6032 dynamic eddy-current braking system and independent brake water cooling system.
2. Mast: Pyramid vertically self-erecting Mast.142ft. high x 24 ft. x 17.5 ft. base. Static hook
load capacity with 12 lines 771k-lbs and 10 lines, 750k-lbs. Design as per API RP 4F, Rated to
105 MPH with full set back.
3. Substructure: Ingersoll-Rand 22ft. high Cross Type Substructure, hydraulically raised and
lowered, 17’ 8” clear height below the bottom of the rotary beams. 750,000 lbs. rotary
capacity, 400,000 lbs. setback capacity and 1,135,000 lbs. maximum simultaneous load
4. Deadline Anchor: National Type “E” deadline anchor with Martin Decker Totco Type E-80
load sensator.
5. Rotary Table: Independent rotary drive system, complete with one (1) Ideco Model LR-275K, 27½” rotary table with API master bushings and split insert bowel. One (1) Varco 27”
“MSPC” pin drive split master bushing, one Ideco two speed transmission and driven by a
GE752 Series wound DC traction motor.
6. Hook Block: Continental-Emsco RA-44 with Web-Wilson hydra-hook, 350-ton rated
capacity block-hook combination, with five (5) 44” sheaves grooved for 1¼” wireline.
7. Swivel: Oilwell Model PC-300. 300-ton rated capacity.
8. Kelly: 5¼” x 40 ft. working length hexagonal
9. Kelly Drive Bushing: Varco 27-HDP, pin drive roller Kelly bushing
10. Elevator Links: 3½” x 132” 350-ton weldless elevator links
11. B.O.P Control Unit: Koomey Type 80 7-station closing unit, with twenty-eight (28) eleven
(11) Ga. cylinder; indrical accumulators, one (1) 30 HP triplex pump, three (3) air pumps, four
(4) sets 1” heat shielded B.O.P. control hoses.
12. B.O.P’s:
one (1) 13-5/8” X 5.000 Psi with 10k bottom flange Shaffer annular preventer.
Two (2) 13- 5/8” X 10k Cameron type “U” Ram Preventers (one double and one
single)
One (1) 13 5/8” 10.000 drilling spool with 4 1/16” 10,000 outlets
13. Tubulars: 15,000 ft. 5” S-135 NC50 Drill Pipe
25 joints 5” Hevi-wate Drill Pipe
10 joints 6½” Spiral Drill Collars
10 joints 8” Spiral Drill Collars
14. Mud Pumps: Two (2) Gardner-Denver Model PZK (PZ-10) Triplex Mud Pumps, 1350 HP
driven by one (1) GE752 Type Series wound DC traction motors, suctions charged by 6” x 5”,
Series 250 centrifugal pumps, driven by a 40 HP AC electric motor. 5,000 psi discharge
pulsation dampeners, unitized on a welded steel oilfield skid.
Reimpet International Corporation, 1302 Miles St., Houston, TX 77015
[email protected]
15. Mud Systems: Shaker Tank:
240 bbl. three (3) compartments, complete with two (2) 6” x 5”
Series 250 centrifugal pumps, powered by 50 HP AC electric motors.
Swaco desilter with sixteen (16) 4” cones, one (1) NOV-BRANDT MA-10, 10
HP mud agitator, three (3) derrick, 3-panel, linear motion shale shakers,
One(1) Swaco M.I. 1,000 gallon vacuum degasser.
Intermediate Tank :
Storage/Active with one (1) 155 bbl. and one (1) 300 bbl.
compartment, complete with three (3) NOV-BRANDT MA-15,
15 HP agitators, bottom guns, internal piping, top mounted
walkways and safety railing.
Suction Tank:
362 bbl. two (2) compartment, complete with two (2) 6” x 5”
Series 250 centrifugal pumps, powered by a 75 HP AC electric
motors, two (2) NOV-BRANDT MA-15, 15 HP mud agitators
one (1) 70 bbl. slugging tank with 5 HP Agitator Chemical hopper
and 6” Barite Manifold.
16. Electrical System: Generators:
Three (3) Caterpillar Model 3512-TA diesel engines, each driving
a KATO 1050 KW, 600 Volt AC generator.
Allen Bradley motor control centers
Ross Hill Model 1400 SCR system
17. Compressed Air System: One (1) Gardner Electra Screw 185 CFM Compressor 50 HP and
one (1) Gardner-Denver Screw Type 30 HP.
One (1) 120 Ga. Air Receiver.
18. Water Tank:
19. Fuel Tank:
One (1) 375 bbl. rectangular water tank
One (1) 12,000 Ga. Baffeled rectangular fuel tank, complete with
one (1) fuel pump, driven by a 5 HP AC electric motor.
20. Instrumentation: One (1) drilling instrumentation panel mounted at Driller’s position
and consisting of one (1) weight indicator, one (1) tong line pull
indicator gauge, two (2) pump pressure indicator gauge and one (1)
rotary torque gauge and one (1) Ross Hill Driller’s control panel.
21. Auxiliary Equipment: Two (2) Braden Model PD-12 hydraulic hoist mounted at rig floor.
Two (2) Braden Mast Boom Hoists.
One (1) Retriever Type electro-hydraulic wireline measuring
device, complete with 15,000 ft. of .092 wireline.
Reimpet International Corporation, 1302 Miles St., Houston, TX 77015
[email protected]
22. Rig Site Structures:
One (1) Rig Floor house mounted at Driller’s position.
One (1) Crew Change House.
23. Miscellaneous Items:
Two (2) sets Varco BJ 5” DP Slips
Two (2) sets Varco BJ 5 GG Elevators
One (1) set Varco BJ HT 55 manual Tongs
One (1) Lister Cold Start
One (1) Varco SSW 40 Pipe Spinner
One (1) Varco 6600 Kelly Spinner
One (1) Trip Tank, 2 Sections, 2 Pumps
One (1) 4” x 3” x 2” 5,000 Choke Manifold, skidded
One (1) Junk Box with contents.
One (1) four compartment Lubster
One (1) Choke Manifold Hose
One (1) Gas Buster on Stand
One (1) Hydraulic powered reserve drilling line spool with wire.
One (1) HPU with controls, with one (1) Detroit 371 Diesel and
one (1) 50 HP electric motor for raising/lowering, and all
hydraulic functions.
One (1) Catwalk Ramp with Catwalks.
One (1) Lot Steps and Stairways for Rig, Substructure, Mud
System and other rig accessories.
Houses for Rig manager, Toolpushers, Mechanics, Electricians,
And Crews.
First Air/Hospital module.
24. Top Drive:
One (1) Varco IDS- 1500T Top Drive
Your cost for this rig will be $10,500,000.00
Delivery: Stock in Columbia
Terms: Payment due at time of order.
Thank you for the opportunity to quote and we look forward to working with you in
the future.
Reimpet International Corporation, 1302 Miles St., Houston, TX 77015
[email protected]