CE MARKING FOR MECHANICAL ENGINEERING 22 October 2014 CE

Transcription

CE MARKING FOR MECHANICAL ENGINEERING 22 October 2014 CE
CE MARKING FOR MECHANICAL ENGINEERING
22 October 2014
This course is based primarily on the Machinery Directive. It provides guidance to
compliance and assists participants to determine the route that is most appropriate,
cost-effective and efficient for their product. For the majority of companies, CE
marking is a self-certification process and involves an evaluation of the product or
equipment either by risk assessment or against a relevant standard.
The course will be interactive and participative, with opportunities for discussion, and
is supported by a practical risk assessment exercise and comprehensive course
notes. On completion, participants should:
 Have gained an understanding of the statutory requirements involved;
 Understand technical requirements and interpret compliance standards;
 Be able to apply risk assessment techniques relevant to CE marking;
 Understand the CE marking process and identify the best route to compliance.
There will be both electrical and mechanical consultants present to answer any
informal questions, plus Invest NI staff to advise of further help and support available.
The course is aimed at managers, engineers, technicians, safety professionals...
anyone involved in the design, development, manufacture, supply, importation, use,
or installation of mechanical and electro-mechanical machinery.
PRESENTERS
INFORMATION
David Corr
TÜV SÜD Product Service Ltd
When:
22 October 2014
9:30am - 5:00pm
Where: Invest NI (Conference Room)
Bedford Square, Bedford Street
Belfast BT2 7ES
Alan Edgar
Queen’s University Belfast
Cost:
Send form/cheque to: Alan Edgar, Queen’s
University Belfast, NI Technology Centre.
Cloreen Park, Belfast BT9 5HN
£75 per Company
(2 delegates maximum).
Cheques made payable to
‘Queen's University Belfast’.
Contacts: Alan Edgar (028 9097 4343)) or Martin
McAteer (077 4787 8189)
tel: 028 9097 4343
fax: 028 9097 4332
email: [email protected]
CE Marking for Mechanical Engineering
CE Marking is mandated by European Directives. Many products are covered by
these directives and, to be placed on the European market, must bear the ‘CE’ mark it's a legal requirement. CE marking is the claim that the product meets the essential
requirements of all relevant Directives, and can be legally supplied and move freely
throughout the EU. When managed properly, it also enhances product credibility and
leads to improved marketability and greater customer confidence & satisfaction.
CONTENT
 Overview of EU legislation in relation to CE Marking









▫ Legislative background / Directives and Standards
▫ Applicable directives / Relationship with EMC & LV Directives
The Machinery Directive covering:
▫ Definitions of a machine / Free movement of goods
▫ Harmonised Standards / New Approach Directives
▫ Technical File / Responsibilities
▫ Complex assemblies and Annex IV machines
▫ Notified Bodies
Essential Health & Safety Requirements (EHSRs)
Declaration of Conformity & Incorporation
Hazard identification and methods of Risk Assessment
Risk Assessment examples
Provision & Use of Work Equipment Regulations (PUWER)
Pressure Equipment Directive (if required)
Introduction to EMC & Low Voltage Directives
CE Marking process and route to compliance
NOTE: Seminar attendees will be asked to complete a post-evaluation questionnaire approx. 12
months after the seminar takes place to ascertain the outcomes and benefits of the training.
CE MARKING FOR MECHANICAL ENGINEERING – 22 October 2014
BOOKING
Please enrol:
FIRST NAME: ____________________________
SURNAME: ________________________
POSITION: ____________________________
FIRST NAME: ____________________________
SURNAME: ________________________
POSITION: ____________________________
Contact:
NAME: ____________________________
ORGANISATION: ___________________________________________________________________
ADDRESS: ___________________________________________________________________
___________________________________________________________________
Invoice:
POSTCODE: ____________________________
TEL: _________________________
E-MAIL: ____________________________
FAX: _________________________
□
Order No: ____________________________
Cheque enclosed:
□
(Payable to ‘Queen’s University Belfast’)
tel: 028 9097 4343
fax: 028 9097 4332
email: [email protected]