Module: 2 Lecture: 5 ACETIC ACID

Transcription

Module: 2 Lecture: 5 ACETIC ACID
Module:2
Lecture:5 Acetic acid
Dr. N. K. Patel
Module: 2
Lecture: 5
ACETIC ACID
INTRODUCTION
Acetic acid, CH3COOH is an organic compound which also written as
CH3CO2H or C2H4O2. It is a colourless liquid in undiluted form is called as
glacial acetic acid. Andreas Libavius in the sixteenth century described a
procedure for preparation of glacial acetic acid through the dry distillation of
certain metal acetates like copper (II) acetate and compared the produced
glacial acetic acid with vinegar. The presence of water in vinegar has such a
profound effect on acetic acid's properties that for centuries chemists
believed that glacial acetic acid and the acid found in vinegar were two
different substances. Later on Pierre Adet proved that both are same. The
very dilute form of acetic acid (8 – 10%) is known as vinegar and has a
distinctive sour taste and pungent smell. Besides its production as household
vinegar, it is mainly produced as a precursor to polyvinyl acetate and
cellulose acetate. Although it is classified as a weak acid, while
concentrated acetic acid is corrosive to the skin.
Due to the global present of acetic acid producing bacteria via air
oxidation of beer and wine vinegar was first known to the society. In the 3rd
century BC, Theophrastus described how vinegar acted on metals to
produce pigments useful in art, including white lead (lead carbonate) and
verdigris, a green mixture of copper salts including copper (II) acetate.
Ancient Romans boiled soured wine in lead pots producing lead acetate rich
highly sweet syrup called as sapa or sugar of lead or sugar of Saturn, which
contributed to lead poisoning among the Roman nobility.
Hermann Kolbe synthesized acetic acid first time from inorganic
compounds in 1847. The reaction sequence consisted of chlorination of
carbon disulfide to carbon tetrachloride, followed by pyrolysis to tetra chloro
ethylene and aqueous chlorination to trichloro acetic acid, and finished with
electrolytic reduction to acetic acid.
NPTEL
1
Module:2
Lecture:5 Acetic acid
Dr. N. K. Patel
In the first decade of twentieth century most glacial acetic acid was
obtained from the "pyro ligneous liquor" from distillation of wood. The acetic
acid was isolated by treatment with milk of lime, and the resulting calcium
acetate was then acidified with sulfuric acid to recover acetic acid.
Henry Dreyfus developed a methanol carbonylation pilot plant in 1925.
However, non-existence of corrosion resistance material at high pressure
(200atm) discouraged commercialization of the route. BASF, established the
first commercial methanol carbonylation process, using a cobalt catalyst in
1963. Later on by Monsanto, developed a rhodium-based catalyst
(cis−[Rh(CO)2I2]−) plant which is operated efficiently at lower pressure with
almost no by-products in 1970. In the late 1990s, BP Chemicals
commercialized the Cativa catalyst ([Ir(CO)2I2]−), which is promoted by
ruthenium for greater efficiency which largely replaced the Monsanto
process.
In 1996 David Mehringer and his team discovered acetic acid in
interstellar medium who detected it using the former Berkeley-IllinoisMaryland Association array at the Hat Creek Radio Observatory and the
former Millimeter Array located at the Owens Valley Radio Observatory. It
was first detected in the Sagittarius B2 North molecular cloud. Acetic acid has
the distinction of being the first molecule discovered in the interstellar
medium using solely radio interferometers; in all previous ISM molecular
discoveries made in the millimeter and centimeter wavelength regimes,
single dish radio telescopes were at least partly responsible for the detections.
The formation of acetic acid furnishes an excellent example of liquidphase oxidation with molecular oxygen. Acetic acid may be obtained by the
direct oxidation of ethanol, but the concentrated acid is generally obtained
by oxidation methods from acetaldehyde that may have been formed by
the hydration of acetylene or the oxidation of ethanol. The oxidation usually
occurs in acetic acid solution in the presence of a catalyst and at
atmospheric or elevated pressures.
Temperatures may range, up to 1000C, depending upon conditions,
but are usually lower.
NPTEL
2
Module:2
Lecture:5 Acetic acid
Dr. N. K. Patel
MANUFACTURE
1.
2.
3.
4.
5.
Acetic acid can be manufactured by following methods
Methanol carbonylation
Acetaldehyde oxidation
Ethylene oxidation
Oxidative fermentation
Anaerobic fermentation
1. Methanol carbonylation
Raw material
Basis: 1000kg acetic acid by methanol carbonylation (95% yield)
Methanol
510kg
Carbon monoxide
445kg
Reaction
Manufacture process
Rhodium catalyzed carbonylation of methanol is carried out in
presence of iodine as activator. Methanol and carbon monoxide were
charged into carbonylation reactor at partial pressure between 10 - 15bar
while the temperature is maintained at 1750C. The exhaust gas from the
reactor is coming out from the top and introduced into gas scrubber where
gases coming out from purification section are also scrubbed using methanol
and then recycle to reactor.
Reactor used in carbonylation of methanol is bubble column reactor.
This reactor provides excellent mass and heat transfer. In this reactor gas is
sparged from the bottom of the reactor. Design of the sparger controls the
bubble size distribution in the column.
While remaining mixture from the reactor is heated in flash tank where
vapour is transferred to crude column for distillation while liquid coming out
from bottom is recycled to reactor. In crude acetic acid column, light end
are vaporized and send to light ends column where they are removed. Liquid
coming out from bottom is again heated in flash tank and acetic acid -
NPTEL
3
Module:2
Lecture:5 Acetic acid
Dr. N. K. Patel
water mixture is taken out from side cut and charged in to dehydration
column where methanol is introduced.
Gas
scrubber
Purge
Flash
tank
CO
Steam
Light end
column
CO
Methanol
Crude acetic
acid column
Carbonylation
reactor
Purge
Waste acid
column
Methanol
Acetic
acid
Acetic acid
column
Dehydration
column
Methanol
Waste
acid
Figure: Manufacture of acetic acid by methanol carbonylation
Block diagram of manufacturing process
Diagram with process equipment
Animation
After dehydration, liquid mixture from bottom of column is charged into
acetic acid column where acetic acid is obtained as product. Waste acid
are removed using stripping operation.
2. Acetaldehyde oxidation
Raw material
Basis: 1000kg acetic acid by acetaldehyde oxidation (87% yield)
NPTEL
4
Module:2
Lecture:5 Acetic acid
Dr. N. K. Patel
Acetaldehyde
Oxygen
845kg
615kg
Reaction
Manufacture process
Nitrogen
Cooled
water
Acetaldehyde
still
Waste
Cold
Water
Water
Scrubber
Heat exchanger
Steam
Air
Oxidizing
kettle
Refined
acetaldehyde
Heat
exchanger
Manganese
acetate
Water
Acetaldehyde from
acetylene hydration
Acetic acid
still
Heat
exchanger
Steam
Crude acetic acid
Refined
acetic acid
Figure: Manufacture of acetic acid from acetaldehyde
Block diagram of manufacturing process
Diagram with process equipment
Animation
Acetaldehyde from acetylene hydration was preheated in heat
exchanger and purified in acetaldehyde still by distillation. Purified
acetaldehyde was stored in refined aldehyde storage tank. Then refined
NPTEL
5
Module:2
Lecture:5 Acetic acid
Dr. N. K. Patel
aldehyde was charged in to oxidation vessel from top in counter current
direction of air as a source of oxygen from bottom.
The reaction vessel consists principally of aluminum-lines steel vessel
fitted with air distributor. In operation, previously cooled acetaldehyde at
0-50C was introduced, and then manganese acetate is added either in the
form of saturated acetic acid solution or as a powder ground to pass 200
mesh sieve. At the same time air was introduced through the distributor head
and temperature was raised by steam by passing through the aluminum coils.
The heat of reaction must be removed by cooling water, which is substituted
for the initial steam. Temperature plays an important role for the oxidation
reaction. It should be maintained 270C for 1st hrs. Then increase of 1 to 20C for
2hrs and gradually increased up to 600C after 4hrs. The most satisfactory
operating temperature is about 600C. The reaction takes 12-14hrs for
completion. The pressure was kept below 5 kg/cm2.
The nitrogen being vented through a series of condensers attached to
the dome. Condensed aldehyde was returned to the kettle. The nitrogen was
passed through water scrubbers to remove the last traces of the aldehyde,
which is later recovered. Acetic acid, exceeding 96% strength was obtained.
Distillation is carried out for final concentration and purification of acid. The
yield varied from 88-95% of the theoretical.
NPTEL
6

Similar documents

Global MonoChloro Acetic Acid Market 2015 Industry Trend, Analysis, Survey and Overview

Global MonoChloro Acetic Acid Market 2015 Industry Trend, Analysis, Survey and Overview "Global MonoChloro Acetic Acid Industry 2015" incorporates an analytical study of the MonoChloro Acetic Acid market, encompassing an in-depth estimation of the market's condition around the globe. This study gives an extensive elaboration on the strategies and analytical methods related to research that have been administered in the formation of this report. It is an inside-out market investigation with inputs from industry leaders. It deploys the SWOT analysis tool as well as Porter’s five forces analysis to examine market information regarding MonoChloro Acetic Acid. Also, this report constitutes a broad study of the applications scope and end users of MonoChloro Acetic Acid around the world. The report is segregated into various parts relevant to distinctive parts of the MonoChloro Acetic Acid market. This market research report determines the present situation and the development possibilities of the MonoChloro Acetic Acid market worldwide in the forecast horizon. Besides, the examination and forecast of the MonoChloro Acetic Acid market has been done on the basis of volume and in order to quantify the market size, the report contemplates the revenue generated by the MonoChloro Acetic Acid market in China as a significant regional player. The key players’ segmentation, on the premise of geography, is additionally given in this report.

More information