APPLICATION NOTE ISP131001 AN140802

Transcription

APPLICATION NOTE
ISP131001
AN140802
Accelero-Magnetometer, Temperature
and Barometer Sensor Demonstration
Introduction
This application note describes how to set up a Sensor application with ISP131001 Sensors Board that
will send data via the Bluetooth link to the Master Emulator or to an Apple Device.
Two types of demonstration are presented.
The first one is directly executable with hardware and software provided in the Development Kit using
Master Control Panel application.
The second demonstration requires the use of an iPhone or an iPad. The iOS application is available on
demand only as an App that can be installed for development purposes via the Apple developer
program. The procedure to obtain the App from Insight SiP and demonstration of the Sensor application
with Apple Device is described hereafter.
Contents
1. Demonstration with Master Control Panel ................................................................................ Page 1-1
2. Demonstration with iPhone or iPad Device .............................................................................. Page 1-4
October 30, 2014
Document Ref: isp_ble_AN140802_R1.docx
Page 1/8
Insight SiP – Green Side – 400 avenue Roumanille – BP 309 – 06906 Sophia-Antipolis Cedex – France – www.insightsip.com
The information contained in this document is the property of Insight SiP and should not be disclosed to any third party
without written permission. Specification subject to change without notice.
APPLICATION NOTE
ISP131001
1. Demonstration with Master Control Panel
1.
2.
3.
4.
5.
Place the CR2032 lithium battery into the battery holder.
Connect the battery holder to the Sensors Board ISP131001.
Connect Development Dongle PCA10000 (Master Emulator) into a USB port on your computer.
Start Master Control Panel.
Click Start Discovery.
October 30, 2014
Page 2/8
APPLICATION NOTE
ISP131001
6.
7.
Click Select Device.
On the following display, click successively on Bond, Service Discovery and Enable Services.
8.
You can note data that transit between the ISP131001 Sensors Board and the Master Emulator via
the Bluetooth link:
Data of the accelerometer/magnetometer on the above left figure
Data of the temperature/pressure on the above right figure
9.
To switch off ISP131001 Sensors Board, disconnect battery holder as seen in the figure below.
October 30, 2014
Page 3/8
APPLICATION NOTE
ISP131001
2. Demonstration with iPhone or iPad Device
The Sensor application is available on demand from Insight SiP. The iOS App is a demonstration App
that is provided "as is" in order to demonstrate the Smart Bluetooth sensor node. Only one iPhone or
iPad is allowed per development kit.
Make sure you iOS device is compatible with Bluetooth 4.0 (iPhone 4S or higher, iPad Air, Mini, 3rd
generation and above).
The installation procedure for the Sensor application is described hereafter:
1.
2.
3.
Contact Insight SiP at [email protected] and communicate the kit number and the product key
notified on the dev kit.
We will send you by email an invitation 24h-48h after. Accept it using your iOS device you want to
use for the demo.
Sign up in order to register to TestFlight app
October 30, 2014
Page 4/8
APPLICATION NOTE
ISP131001
4.
Connect your device. It will create a TestFlight icon on your device.
5.
Once you receive an install email of available build, open again your TestFlight app from your
device. It can take additional 24-48 hours to receive this email.
Click on “View All Apps” and then click on “Install”.
6.
October 30, 2014
Page 5/8
APPLICATION NOTE
ISP131001
7.
The InsightSiPDemo application is downloaded and installed. You should see the following screen
on your iOS device.
Then you will be able to set up the application demonstration as follows:
8. Place the CR2032 lithium battery into the battery holder.
9. Connect the battery holder to the Sensors Board ISP131001.
10. Start InsightSiPDemo application on your iOS, click Connect and select your Sensors Board (name
is InsightSiP_xxxxx).
October 30, 2014
Page 6/8
APPLICATION NOTE
ISP131001
11. Click Accelerometer. A Calibration phase invites you to rotate the ISP131001 Sensors Board. Then,
a starship on your iPhone screen follows the Sensors board movement.
12. Click Back and Temperature to start temperature and pressure demonstration.
October 30, 2014
Page 7/8
APPLICATION NOTE
ISP131001
13. Click Back and LED. A prompt will invite you to pair the Sensors Board with the iPhone. Click Pair.
The LED lights up.
14. To switch off ISP131001 Sensors Board, disconnect battery holder as seen in the figure below.
October 30, 2014
Page 8/8

APPLICATION NOTE ISP131001 AN140802

Transcription

Similar documents

BLE MODULE ISP091201 Bluetooth Low Energy Module

Which two heads are better than one?

a flyer on making the transition to IP

Turn the page to see the prettiest little Camel Toe you`ve ever seen!

PJSIP - eLinux.org

Find out how to use your Grandstream GXV- 3000 $299.00* GRANDSTREAM VIDEOPHONE FEATURES

How to configure SIP using STC ALP Spirent Test Center 1

Guide to Problem Solving

ZX50 SPEC V3

VS-GW1200-4G Datasheet