of Hansu Controls

Transcription

of Hansu Controls
Dated:03/Dec/2014
HANSU CONTROLS
: PLOT-W-281(A) T.T.C. INDS AREA, MIDC, RABALE NAVI MUMBAI - 400701 MAHARASHTRA INDIA.
PHONE No. : (022) 65193145, 27690037
MOBILE No. : 9821550302,9821185228
FAX No. : 27690038
ADDRESS
E-MAIL
: [email protected], [email protected]
CST TIN No. : 27270691652 DT:22.01.09
PAN No.
: AFZPS4414A
BANK
: HDFC BANK LTD
WEBSITE
VAT TIN No.
SSI REG.
ACCOUNT No.
: 04062320000957
RTGS/NEFT/IFSC
: www.hansucontrols.com
:
: 270211101280 DT:16.09.08
Branch:
: HDFC0000406
Ghatkopar (W)
Complete Details of HA54
Group HA) SPECIFICATION & PRODUCTS FOR C.A INDUSTRIAL WP/FLP JUNCTION BOXES/TERMINAL BOXES IN CAST
ALUMINIUM (LM-6)/FRP/POLYCARBONATE/FLP ENCLOSURES :- Supply of Cast Aluminium JUNCTION BOXES dust, vermain and
weatherproof suitable for wall/Structure mounting. All the enclosures are cast out of superior quality aluminium alloy. All the surfaces are
carefully cleaned and levelled so as to give very smooth surface. All the enclosures are chromatised and finally epoxy powder coated by static
charge spray method by light grey shade 631 as per IS5. Powder coating gives very tough durable and extremely smooth surface. All the mating
surfaces are provided with round rubber gasket in the groove so as to make it effectively dust and vermain proof. Typical enclosures with
different types of actuators mounted are tested by many of our customers for IP65 Class of protection. Our Junction Boxes are suitable for
outdoor installation without any canopy.
MOUNTING IN CAST ALUMINIUM :- Mounting holes are inside or external four lugs are provided for fixing. The lugs offset in such a way that
the rear part of the unit stays away from the surface by at least 3mm.
FIXING OF TERMINALS :- For wall mounting /Structure Mounting J.Box terminals are fixed inside the box. Cover is fixed bolted type.
CABLE ENTRIES :- Threaded cable entries are provided on any side of Terminal Box.
HARDWARE :- All external hardwares used will be Stainless Steel.
EARTHING :- Earthing is provided on both sides of the enclosures by 5mm screw with two plain washers and spring washer of brass.
INSPECTION & TESTING :- Each J.B.will be subjected to routine tests in accordance with relevant Indian Standards & including the following:
(1) Dimensional check as per drawing. (2) Operation test. (3) Insulation test with 500V Megger. (4) HV Test at 2KV for 60 Seconds. (5) Earth
continuity test.
ADVANTAGES OF CAST ALUMINIUM J.B.SHEET METAL FABRICATED J.B. :- (1) Cast Aluminium J.B. enclosures can be made in any
desired and convenient shape and thus ensuring dust, vermin and weather proofness. It is impossible to get any desired shape in sheet metal.
(2) In case of Cast Aluminium all individual pieces will be exactly of same size and shape as these are cast out of same mould. Fabricated boxes
are likely to vary in shape on account of human error and other difficulties. (3) Finishing of Cast Aluminium will be superb and same is not
possible in small fabricated boxes.(4) Aluminium is lightweight and non-corrosive whereas sheet metal is heavy and corrosive. Cast Aluminium
has even good scrap value.
SALIENT FEATURES FOR CAST ALUMINIUM :- (a) Each J.B. is in Cast Aluminium enclosure & epoxy powder coated.(b) Terminals are elmax
clip on type, which are known for quality and reliability. Even spares are available freely anywhere in India.(c) Better than IP65 Class of
Protection.(d) Non deteriorating Neoprene sponge rubber gasket.
SPECIFICATION & PRODUCTS FOR FRP/POLY CARBONATE :- Supply of F R P J.B. dust, vermin and weather proof suitable for
Wall/structure mounting. All the enclosures are HOT moulded out of superior quality SMC compound. All the mating surfaces are provided with
round rubber gasket so as to make it effectively dust and vermin proof. Typical enclosures with different types of actuators mounted are tested
by many of our customers for confirmation to IP65 Class of protection. Our Junction Boxes are suitable for outdoor installation without any
canopy.
SALIENT FEATURES FOR FRP :- (a)Each Terminal Box is in FRP enclosures and is hot moulded out of SMC/DMC compound. (b) Terminals
are Elmax/connectwell make, which are known for quality and reliability. Better than IP65 Class of Protection (c) Non-deteriorating Neoprene
sponge rubber gasket.S.S.Screws for cover fixing. (d) Superior finish.
MOUNTING IN FRP :- Internal holes are given for mounting. External legs can be provided, if required.
SPECIFICATION & PRODUCTS FOR FLP :- Cast Aluminium LM6 J.Boxes dust, vermin and Flameproof /weatherproof suitable for
wall/Structure mounting. All the enclosures are cast out of superior quality Aluminium alloy. All the surfaces are carefully cleaned and leveled
so as to give very smooth surface. All the enclosures are chromatised and finally epoxy powder coated by static charge spray method by light
grey shade 631 as per IS5. Powder coating gives very tough durable and extremely smooth coating on the surface. All the mating surfaces are
provided with round rubber gasket in the groove so as to make it effectively dust and vermin proof. Enclosures are tested at CMRI for
flameproof and weather proof test IP65 as per IS 2147.Our Terminal Boxes suitable for outdoor installation without any canopy.
NAME PLATE FOR FLP :- Each Terminal Box is provided with nameplate giving equipment description.
INSPECTION & TESTING FOR FLP :- Each Box is subjected to routine tests in accordance with relevant Indian Standards including following:
(1) Dimensional check as per drawing. (2) Operation test. (3) Insulation test with 500V Megger. (4) HV Test at 2KV for 60 Sec. (5) Earth continuity
test.6) Hydraulic Test 7) Impact test.8) Surface Test.
Page 1 of 3
Dated:03/Dec/2014
Product Drawing
Code :- HA54
Size :- 160mm CLEAR DIA.
Specification :- DESIGN MANUFACTURE & SUPPLY OF FLP\WP JUNCTION BOX
IN CAST ALUMINIUM LM-6 ENCLOSURE WITHOUT CANOPY SUITABLE FOR
INSTALLATION IN GAS GROUP I, IIA AND IIB AREA COMPLETE WITH
MAXIMUM 24NOS.2.5SQMM ELMAX TYPE TERMINALS. MAXIMUM 8:3/4"ET
CABLE ENTRY CAN BE PROVIDED AT THE BOTTOM. 5:3/4"ET CABLE ENTRY
CAN BE PROVIDED. CMRI CERTIFICATE NO CMRI\TC\H280 Dt 14.3.96
Wt.4.5Kg.App.
Unit Rate in Respective Currencies : *
DESCRIPTION
INDIAN
US DOLLAR
RUPEE
JB WITHOUT TERMINALS
` 1700.00
$ 28.33
JB WITH 24 TERMINALS
` 1988.00
$ 33.13
FLP/WP JB
BOTTOM VIEW
SIDE VIEW
OPEN VIEW
Extra Cost for Providing : *
Sr. No.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DESCRIPTION
WIRING WITH 2 WIRES & 2 TERMINALS.
30A 4 WAY OR 15A 6 WAY OPEN TYPE TERMINAL.
2.5SQMM ELMEX TYPE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
4SQMM ELMEX TYPE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
6SQMM ELMEX TYPE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
10SQMM ELMEX TYPE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
2.5SQMM PHOENIX MAKE TERMINAL WITH CHANNEL, END STOP AND END PLATE.
M3 STUD TYPE TERMINAL UPTO 6SQMM CABLE.
M4 STUD TYPE TERMINAL UPTO 10SQMM CABLE.
M5 STUD TYPE TERMINAL UPTO 16SQMM CABLE.
M6 STUD TYPE TERMINAL UPTO 25SQMM CABLE.
M6 STUD TYPE TERMINAL UPTO 35SQMM CABLE.
INSULATED EARTH BAR UPTO 6 WAY.
INSULATED EARTH BAR UPTO 12 WAY.
INSULATED EARTH BAR UPTO 18 WAY.
INSULATED EARTH BAR UPTO 24 WAY.
TELEPHONE SHOE FOR TELEPHONE CONNECTION.
SS HINGE (A SET OF TWO).
3/4", 1" OR 1 1/4" PVC PLUG.
BUS BAR TYPE TERMINAL 35-50SQMM CBT110
BUS BAR TYPE TERMINAL 50-70SQMM CBT170
SHORTING LINK FOR A SET OF TWO TERMINALS WITH SHORTING STUD & LINK.
BUS BAR TYPE TERMINAL 70-95SQMM CBT250
1/2"NPT S.S. PLUG FOR FLP ENCLOSURES
INDIAN RUPEE
` 60.00
` 30.00
` 12.00
` 13.00
` 14.00
` 16.00
` 15.00
` 30.00
` 30.00
` 40.00
` 50.00
` 60.00
` 50.00
` 100.00
` 150.00
` 200.00
` 200.00
` 150.00
` 5.00
` 100.00
` 140.00
` 10.00
` 200.00
` 60.00
US DOLLAR
$ 1.00
$ 0.50
$ 0.20
$ 0.22
$ 0.23
$ 0.27
$ 0.25
$ 0.50
$ 0.50
$ 0.67
$ 0.83
$ 1.00
$ 0.83
$ 1.67
$ 2.50
$ 3.33
$ 3.33
$ 2.50
$ 0.08
$ 1.67
$ 2.33
$ 0.17
$ 3.33
$ 1.00
Page 2 of 3
Dated:03/Dec/2014
25
26
27
28
29
30
31
32
33
34
35
1/2"NPT S.S. CABLE GLAND FOR FLP ENCLOSURES
1 1/4"NPT S.S.CABLE GLAND FOR FLP ENCLOSURES
HINGED DOOR + DOOR HANDLE + KEY LOCKING ARRANGEMENT COMPLETE SET
FLP/WP 3/4"DC BRASS NICKLE PLATED CABLE GLAND FOR FLP ENCLOSURES
FLP/WP 1/2" NPT DC S.S. PLUG FOR FLP ENCLOSURES
FLP/WP 1/2" NPT DC S.S. CABLE GLAND FOR FLP ENCLOSURES
FLP/WP 1 1/4" NPT DC S.S. CABLE GLAND FOR FLP ENCLOSURES
3/4" FLP MS PLUG. FOR FLP ENCLOSURES
11/4" FLP MS PLUG. FOR FLP ENCLOSURES
1" FLP MSPLUG. FOR FLP ENCLOSURES
SS NAME PLATE WITH ENGRAVING
` 250.00
` 800.00
` 650.00
` 80.00
` 60.00
` 250.00
` 800.00
` 20.00
` 50.00
` 30.00
` 100.00
$ 4.17
$ 13.33
$ 10.83
$ 1.33
$ 1.00
$ 4.17
$ 13.33
$ 0.33
$ 0.83
$ 0.50
$ 1.67
* The prices shown above may vary with time.
Page 3 of 3