yolbi̇r maki̇na

Transcription

yolbi̇r maki̇na
YOLBIR MAKINA
PLASTIC CRUSHING MACHINES
WASTE CABLE RECYCLING AND COPPER SIEVING PLANT
MACHINE MANUFACTURING AND DESIGN
SETTING UP TURNKEY-DELIVERY PLANTS
ADDRESS : Gümüş suyu Cad. Litros Yolu, Fatih Şehitleri Sokak,
Yildiz Han, B Blok, No: 81
Topkapi – Maltepe / ISTANBUL
TEL
: 090 212 565 64 47
FAX: 565 45 26
GSM
: 0535 769 63 13 - 0532 615 07 99
V.D.
: DAVUTPASA 981 005 85 29
YOLBIR MAKINA is a prestigious company with in-depth experience and
background since 1972. The company is primarily engaged in cable recycling
machines and plastic crushing machines. The company had also undertaken various
contracting manufacturing jobs before. The machines we manufacture are
distinguished in terms of
-
technical structure
-
design
-
engineering services and
-
quality of materials employed.
We are committed to maintaining and further improving our corporate assets above,
consistently offering supreme-quality service to our customers, fulfilling the demands
of customers to their full satisfaction, manufacturing sophisticated, reliable and
durable machines, and providing full service for every machine we have
manufactured.
TYPES AND SPECIFICATIONS OF OUR MACHINES
Type (cm)
30-cm
35-cm
40-cm
45-cm
50-cm
60-cm
70-cm
80-cm
Jaw height (mm)
1250
1250
1300
1350
1350
1400
1430
1450
Machine width (mm)
1000
1050
1060
1100
1180
1200
1300
1400
850
900
950
1100
1150
1200
1450
1450
Depth (mm)
Number of rotary blades
3 – 5 blades
Number of fixed blades
2
Engine kWA
Output kg/h
These are average values and may vary according
to the raw materials used
11
15
18,5
22
30
37
55
55
150
200
250
350
400
450
550
600
1800
1850
Sieve mesh diameter
Machine weight
(kg-approximately)
Wir fertigen in gewünschten Durchmessern
500
700
900
1200
1600
1700
YOLBIR MAKINA
PLASTIC CRUSHING MACHINES
WASTE CABLE RECYCLING AND COPPER SIEVING PLANT
MACHINE MANUFACTURING AND DESIGN
SETTING UP TURNKEY-DELIVERY PLANTS
ADDRESS : Gümüş suyu Cad. Litros Yolu, Fatih Şehitleri Sokak,
Yildiz Han, B Blok, No: 81
Topkapi – Maltepe / ISTANBUL
TEL
: 090 212 565 64 47
FAX: 565 45 26
GSM
: 0535 769 63 13 - 0532 615 07 99
V.D.
: DAVUTPASA 981 005 85 29
OPERATING MANUAL
First, position the machine
balanced before operating it.
well-
Refer to a qualified electrician for the
electrical connections of the machine.
Check that the safety system is ready
to operate.
Check that emergency stop is ready to
operate.
Check that the switch is on when the
machine is started.
Effect the operational adjustments of
the machine, check and then
commission the machine
As a daily maintenance, check the
grease level in roller bearings.
If possible, please use the grease type TEMP 90 L 12 V.
ATTENTION: Strictly cut off the mains power during any maintenance, repair or
blade adjustment.
Do not wire any machine other than your system to the switchboard.
Do not attempt to operate the machine while the upper cover is open.
Do not operate the machine unless the flywheel housings are fitted.
Cut or shrink long work pieces before feeding them to the machine.
Strictly comply with
safe working
principles
The switch prevents the
machine
from
starting
while the upper cover is
open.
Strictly connect.
After
starting
shutting
the
and
machine,
strictly tighten the bolts
that unite the upper and
lower covers.
Do not commission the
machine
without
tightening.
Start-Stop
button:
Use
this button for ordinary or
emergency stop when the
machine is in operation.
The
operation
of
the
machine may be resumed
via the control panel by
reinstating
the
emergency stop button.
BLADE ADJUSTMENT
BLADE ADJUSTMENT
1. Position the rear fixed blade
properly and tighten its bolts
in place to install the unit
reliably.
2. Adjust the blades on the
rotor properly so that they
travel very closely to the
fixed blade without touching
it, and then tighten them in a
controlled manner and then
fix.
This procedure is repeated for
all blades on the rotor.
Finally, adjust the blade on the front section of the machine and tighten as illustrated
above.
Note: After this procedure is completed, check and tighten the bolts that fix all of
the blades for safety purposes.
BLADE CONNECTION
Adjust and connect the blades as illustrated below:
ARKA BIÇAK
BICAK
RODOR
ÖN BIÇAK
ELEK
:
:
:
:
:
REAR BLADE
BLADE
ROTOR
FRONT BLADE
SIEVE
FILTER
Catches and compiles the
dust and cotton particles
coming away from the
sieving
machine
prevents
these
and
particles
from getting widespread in
the environment.
Facilitates to medical and
environmental issues.
The collected dust and
cotton particles are stored
in
the
reservoir
fitted
underneath the machine,
therefore
contaminants
these
can
be
handled and removed in
bulk form.