"MEMS DESIGN, TECHNOLOGY & APPLICATION" 1

•
REGISTRATION FEE
Participation from Academic Institutions, Industry and other Organizations Rs. 7000/- per person.
(This fee is inclusive of registration, lodging & boarding*, travel to workshop venue at ITM University, Gurgaon
and delegate kit). * Double occupancy in IIT Delhi Faculty Guest House.
•
•
Participation fee without accomodation : Rs. 2500/- per person.
Participation from ITM University: Free for first 5 faculty members and 5 students on the
basis of early bird registration scheme. Subsequent registration will be of Rs. 1000/- per entry.
………………………………………………………………………………………………………
THE CHEQUE / DRAFT REMITTANCE DETAIL
Account Holder Name: ITM University
Account No: 82471010000651
Nature of Account: Current Account
Bank Details: Syndicate Bank
Branch Name: ITM University Branch,
MICR Code: 110025148
Gurgaon – 122017, Haryana
IFCS Code: SYNB0008247
REGISTRATION REQUEST FORM
Name of the Participant(s)…………………………………...................................................................…
Number of Participants………………………….………….....…………………………..…………...
Organization…………………………………………………………………………......…………..
Mobile No…………………… Landline No………..…………….Fax No.:………….………………
Address………………………………………………………………………………………………
……………………………………………………...........……………………..……………………..
…………………………………………………………………………....……………………………
Cheque / Draft no:………………………...........…… Date............................................................................
Amount………......................................................................................................…………………………
SPONSORED BY
THE REGISTRATION REQUEST CAN BE SENT TO:
Dr Bharti Arora, Deputy Dean RDIL, ITM University, Sector 23-A, Gurgaon, Haryana –122017
The detail information is also available at: www.itmindia.edu
About ITM University
ITM University (formerly Institute of Technology and Management) was founded in 1996, to promote excellence
in Technical and Management education by Educate India Society, registered under the Registration of Societies
Act of 1860. The University was conceived in response to the acute deficiency of centres of higher learning in the
country to meet the technology and management challenges of the 21st century. The founders had a clear and
well defined mission - to build an unaided, self - financed resource university committed to delivering education of
internationally recognized standards, a university that would go on to serve as an intellectual resource base in
India and the sub-continent.
NATIONAL WORKSHOP
ON
MEMS DESIGN, TECHNOLOGY & APPLICATION
1st to 3rd March 2015
VENUE: ITM University Campus, Sector-23A, Gurgaon
List of Speakers
Calendar and Activity for the Workshop on
“MEMS Design, Technology & Application”
Seminar Room, ITM University, Sector 23 –A, Gurgaon, Haryana
Dr R Muralidharan
Director
Solid State Physics
Laboratory, Delhi
Prof. Prem Vrat
Pro-Chancellor
ITM University
Gurgaon
Dr Surinder Singh
Director SCL
Chandigarh
Prof. Kehar Singh
Ex-Dean & Emeritus Fellow
IIT Delhi
Coordinator: Dr Madhusudan Singh, IIT Delhi
Co-Coordinator: Dr Bharti Arora (RDIL), ITM University, Gurgaon
E-mail:[email protected] and [email protected]
Tel (O): +91-124-2365811/12, Fax: +91-124-2367488, Mobile: +91-9999928575
Contact Details:
Name
E-mail
Mobile:
Prof. BS Panwar
Vice Chancellor
ITM University
Gurgaon
Prof. S D Joshi
Professor
Dept. of Electrical Engg.
IIT Delhi
Prof. R S Tomar
Professor
LNMIT Jaipur
Dr Madhusudan Singh
Associate Professor
Dept. of Electrical Engg.
IIT Delhi
Dr Bharti Arora
[email protected]
+91-8826034038
Mr Rohit Chhabra
[email protected]
+91-9990588393
SUMMARY OF LECTURES:
Inauguration by : Dr R Muralidharan, Director, Solid State Physics Laboratory, Delhi
Address by: Prof. Prem Vrat, Pro-chancellor ITM University, Gurgaon, Haryana
Plenary Session Chaired by : Dr Surinder Singh, Director, SCL, Chandigarh
TOPICS TO BE COVERED IN TECHNICAL SESSION:
Dr Mukul Sarkar
Assistant Professor
Dept. of Electrical Engg.
IIT Delhi
Dr Supreet Singh Bahga
Assistant Professor
Dept. of Mechanical Engg.
IIT Delhi
Dr R K Bhan
Scientist G
Solid State Physics
Laboratory, Delhi
Dr Bhaskar Mitra
Assistant Professor
Dept. of Electrical Engg.
IIT Delhi
— MEMS Device Design, Technology and Application,
— Device fabrication steps, micro-fabrication steps, Microfluidics MEMS, lab-on-chip,
wet and dry etching techniques
— Accelerometers, micro-detonator based fusing, MEMS based energy harvester
— RF MEMs design sensing, and millimeter wave technology and sensor,
— Hands on training on MEMS CAD tools.