THE WORLDS FIRSTAND ONLY USER
Transcription
THE WORLDS FIRSTAND ONLY USER
SONIC is delivered in 3 different diameters. SONIC distributors: MODULAR SUPPRESSOR Skytesport AS [email protected] The SONIC range of modular suppressors have been developed using the latest in precision engineering techniques, combining lightweight materials with a unique design. All SONIC suppressors feature a modular system with steel reinforcement for maximum flexibility and durability in the most extreme conditions. It provides marketleading noise suppression with possibly the lightest weight in its class. Finished with a sealed “over-barrel” self-tightening telescopic rear chamber, ounce for ounce the SONIC will beat any competitor when comparing weight vs. noise vs. price. J. Nielsen Design AS [email protected] Classic Vapen AB [email protected] Highland Outdoors Ltd. [email protected] Cameron Sports Imports Ltd. [email protected] THE WORLDS FIRST AND ONLY USER ADJUSTABLE MUZZLE BRAKE. The SONIC Trimbrake is the first and only muzzle brake which lets everyone mount and trim the brake themselves. Simply tread it on and trim the brake by plugging the gas vents with the supplied screws. The Sonic trimbrakes self-tightening design makes sure it stays securely in place. Available in the following calibers: Max 6mm / 7mm / 8mm / 9,5mm TEST TRIMBRAKE “SIMPLE, LOGICAL AND IT WORKS!” - Alf Martin Bråten, JHV Oktober 2011 The illustration shows the fitting of the back shroud to the thread of the muzzle. This clearly shows the possibility of shorter overall barrel length compared to its competitors. 0-point in the table shows the end of the barrel before threading. TH TOTAL LENG LENGTH 5 MM • SONIC55: 29 IC WRAP TELESCOP C35: 240 MM 5 MM • SONI SONIC45: 25 16-30 16-20 16-20 16-20 16-20 20 5: 115 MM M • SONIC3 C45: 140M 0 MM • SONI SONIC55: 14 Fig. 1 For Magnum calibers 5 threaded baffles. Allround-model The built in self-tightening flash hider is designed to direct the propellant gases in such a way that the suppressor will self-tighten. The baffles have a steel center lining which is our unique designed to prevent erosion. www.seeview.no Available in the following calibers: Max 6mm, Max 7mm, Max 8mm and Max 9,5mm. SONIC has a telescopic rear chamber that captures propellant gas, and provides a significantly better suppressing effect. For rimfire 22 and airguns Special for cal.17HMR/WSM The rear telescopic section is available with the following thread sizes: 1/2x20”, 1/2x28”, M 13x1, M 14x1, M 14x1,5, M 15x1, M 18x1 and 5/8 UNF. Other threads: On special order. The Suppressor is made primarily of aluminium. This provides an overall weight of Sonic55: 710g. Lenght: 295mm Sonic45: 480g. Lenght: 255mm Sonic35: 300g. Lenght: 240mm dia.35-55 mm Light-weight! Modular design enables adding baffles for greater effect or removal for lower weight. Accessories Specially made customized tool for easy assembly and disassembly of the SONIC suppressors. Heat resistant grease syringe to treat the threads. Both are available as separate parts. SONIC tool SONIC is available in the following thread sizes: Thread d1 d2 d3 (min. dia.) 1/2 x 20” 1/2 x 28” M 13 x 1 M 14 x 1 M 14 x 1,5 M 15 x 1* M 18 x 1* (see fig. 1) 12,70 12,70 13,00 14,00 14,00 15,00 18,00 11,43 11,79 12,00 13,00 12,50 14,00 17,00 d4 (CrMo/Stainless) 14,00 7,40/6,90 14,00 7,82/7,42 14,00 8,00/7,50 15,00 9,00/8,50 15,00 8,50/8,00 16,00 10,00/9,50 19,00 13,00/12,50 Grease Syringe. 5 ml Before threading d2 dia. = The bottom diameter thread is from +0-0.02 to 1,5mm length, 60 degree cone up to d1. d1 dia. = Thread nominal diameter is from +0-0.02, ends with r0.4 and plan rotation of parapet plat to outer diameter. (It is not advisable to make track as this will reduce the strength and stiffness. This is a prerequisite to avoid damage to the barrel with limited wall thickness). d3 = Minimum recommended barrel diameter. Thread will have a finished bottom diameter up to 0,5-1,5 mm from the parapet plat. d4 = Max recommended caliber. The POM-ring has to be extended to the actual barrel diameter on the support point from +0,1 to 0 in diameter. Before mounting The thread is made with a cylindrical piece in both front and rear end for maximum stiffness. This combined with the accompanying POM-ring to the rear end of the telescopic piece provides superior stability and toughness of the damper and mounting. Combined with the short build length of the build and the symmetrical baffle design, it becomes an unprecedented precision suppressor with minimal changes in point of impact before and after assembly or removal.