Swapping due to faulty (Satellite)

Satellite Version
Replace your iQ3
Follow these simple steps to swap your current box with your new iQ3.
1 Connect your new iQ3
B
13V/18VDC
350A max
Combined
Input 1
on’t be a maverick – make sure your TV and existing Foxtel
D
iQ3 are turned off at the wall.
Digital Audio Out
Input 2
Remove the cables from your old iQ3, and connect them into
the same socket on your new box, one by one.
E
12V DC
5A max
Optical
TV aerial
D
C
Coaxial
HDMI
USB
5V DC 500mA
Ethernet
A
USB
ETHERNET
HDMI
SPDIF
and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license from Dolby Laboratories. “Dolby”
VIDEO
Y
RF IN
LNB-IN1
RF OUT
LNB-IN2
Satellite
Pb
RS-232
Australia Pty Ltd
THOMSON
Telecom
Once you’re connected, turn your TV and iQ3 on and select the
HDMI source you’ve connected to.
S-VIDEO
Terrestrial
Pr
U.S. patent Nos 4,631,603 ; 4,577, 216
and 4,819,098 licensed for limited
pay per view uses only
Terrestrial
RS-232
RF OUT
N10406
RF IN
To Foxtel
wall plate
To TV
Y
LNB-IN2
LNB-IN2
Satellite
RF OUT
Y
Australia Pty Ltd
THOMSON
ETHERNETTelecom
S-VIDEO
DDP060AUS / T500
Terrestrial
To internet
access
point
Telecom
THOMSON
VIDEO
Pb
SPDIF
USB
and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license from Dolby Laboratories. “Dolby”
pay per view uses only
and 4,819,098 licensed for limited
U.S. patent Nos 4,631,603 ; 4,577, 216
(optional)
USB
Pb
VIDEO
Australia Pty Ltd
LNB-IN1
LNB-IN1
CSO6460V
To TV aerial
wall plate
SPDIF
Satellite
RF IN
N10406
TV
Pr
S-VIDEO
ETHERNETTelecom
THOMSON
CSO6460V
RS-232
TV
Manufactured under license from Dolby Laboratories. “Dolby”
and the double-D symbol are trademarks of Dolby Laboratories.
DDP060AUS / T500
Pr
To power
point
(optional)
Terrestrial
TV
TV
Pr
2 Bluetooth pairing your iQ3 remote
Bring your
remote to the
front of the iQ3
until the front of
the box lights up.
Reset your existing
remote by pressing
the button located
underneath the
battery cover.
The iQ3 will light up when
it connects with your
remote. Once the lights
on the iQ3 and remote
stop flashing, you’re set.
Press any
button on your
remote until
the blue light
starts to flash.
3 Connecting your iQ3 to the internet
To get the most out of your iQ3 features, connect your Ethernet lead from your modem to the back of the iQ3, or connect to WiFi by following these steps:
Select Home on your iQ3
remote, then arrow right
and select Settings.
Select Internet Connection.
Select WiFi.
Select your network.
Enter your WiFi password,
select Done and you will be
advised once connected.
4 Tune those channels
To receive your local free-to-air channels* from your TV aerial, check you’ve connected your iQ3 to your aerial wall plate, then:
Select Home, arrow right
and select Settings.
Select Terrestrial
Channels from Settings.
Select Full Scan.
Select Begin Scan.
5 Activating your iQ3
Nearly done!
n the sticker on the outside of your iQ3
O
carton, find your box number (the first 16
digits only) and your smartcard number.
Then call
1300 732 681
and follow the prompts
FOX0020 09/14 SAT/REP
You’re now up and running
Make sure you return your old iQ3 to us so we can check what went wrong.
Just take the enclosed letter, label and your old iQ3 to an Australia Post outlet
and we’ll take care of the rest.
For troubleshooting or support, go to the Help section in your iQ3 Settings
or visit foxtel.com.au/support
*Free-to-air channels will vary based on location and not all channels are available in all areas.
Once scan is complete
select View TV Guide.