Construction - Sika Canada

Construction
Chemical Anchoring Systems
Epoxy and Acrylic Resins
Applications
A
B
C
E
F
Construction
G
D
E
F
G
D
A Various brackets and supports
B D.O.T. dowels, guard rails and “jersey” barriers
C Baseplates, safety rails and vibrating equipment
Typical Applications
D Bolts and special fastening system
E Substitute for cast-in-place anchors
F Anchor through brick and solid concrete
G Can be used for anchoring to hollow brick or block
(with perforated screen tubes)
Sika® AnchorFix® Cartridge
Sika® AnchorFix®-1
Sika® AnchorFix®-1 is a methacrylate 2-part polyester
anchoring adhesive, which sets up in just minutes and
will cure at temperatures as low as -10ºC (14ºF).
Sika® AnchorFix®-2CA
Sika® AnchorFix®-2CA an epoxy acrylate exhibits high
load capacities, can be dispensed in all types of
weather conditions and will cure in colder base material
temperatures down to -26 °C.
Sika® AnchorFix®-3CA
The professional contractor will enjoy the advantages of
100% solids epoxy with superior bond strengths and fast
cure times allowing for same day loading of heavy-duty
anchors, in concrete, masonry or wood base materials.
Sika® AnchorFix®-4CA
Excellent long term performance and the same superior
bond strengths provided by Sika® AnchorFix®-3CA. Meets
the commercial construction industry’s demand for regular
set epoxy, with high strength and reliable adhesion to
concrete, masonry or wood base materials.
Advantages
Sika® AnchorFix®-1
Recommended
Thickness (min. / max.)
Installation
Temperature
Cure Rate ( ° C )
Installation
Shelf-Life
Packaging
Approvals
Features
Specifications
Sika® AnchorFix®-2CA Sika® AnchorFix®-3CA Sika® AnchorFix®-4CA
Acrylate
Hybrid Epoxy Acrylate
100% Solid Epoxy
100% Solid Epoxy
1 mm to 3 mm
1 mm to 3 mm
1 mm to 13 mm
1 mm to 13 mm
-10 °C to +40 °C
-26 °C to +40 °C
+5 °C to +40 °C
+10 °C to +40 °C
-10
24 hrs
+5
145 mins
+20
50 mins
+30
35 mins
Overhead
Vertical
Horizontal
-26
-10
+20
+38
+5
+20
+38
+5
+20
+38
36 hrs
6 hrs
35 mins
25 mins
24 hrs
3 hrs
1 hr
NR
12 hrs
4 hrs
Vertical
Horizontal
Vertical
Horizontal
Overhead
Vertical
Horizontal
12 months
12 months
24 months
24 months
300 mL ctrg
275 mL ctrg
825 mL ctrg
None
ICC
MTQ
CFIA
Economical
Low temperature
Very low temperature
Fast setting
Wet and damp holes
Fast setting
Wet and damp holes
Regular setting
Wet and damp holes
2 component / 10:1 ratio
2 component / 10:1 ratio
2 component / 1:1 ratio
2 component / 1:1 ratio
250 mL ctrg
600 mL ctrg
1500 mL ctrg
Bulk Pails
ICC
MTQ
NSF
CFIA
Per NTSB safety recommendations, the use of adhesive anchors are prohibited in sustained overhead load applications
600 mL ctrg
Bulk Pails
MTQ
NSF
CFIA
Technical Data for Sika® AnchorFix®
Tension in 27.5 MPa (4000psi) min. Concrete
Load Capacities for
Sika® AnchorFix® Adhesives
Bit Diameter
Construction
Anchor Size
Thrd Rod
mm (in.)
Rebar
mm (in.)
Sika® AnchorFix®-1
Sika® AnchorFix®-2CA
Shear (A193B7)
Sika® AnchorFix®-3CA &
Sika® AnchorFix®-4CA
All Sika® AnchorFix®
Adhesives
Embedment
Depth mm (in.)
Allowable
Load
kN (lb)
Avg. Ult.
Load
kN (lb)
Allowable
Load
kN(lb)
Avg. Ult.
Load
kN (lb)
Allowable
Load
kN (lb)
Avg. Ult.
Load
kN (lb)
Allowable
Load
kN (lb)
Avg. Ult.
Load
kN (lb)
10 mm or 10M
11mm (7/16")
(3/8" or No. 3)
12mm (1/2")
90mm (3-1/2")
6.1 (1380)
24.6 (5520)
12.3 (2768)
49.3 (11075)
10.5 (2370)
42.2 (9487)
5.0 (1125)
20.0 (4500)
12 mm
(1/2" or No. 4)
14mm (9/16")
15mm (5/8")
110mm (4-1/4")
7.8 (1755)
31.2 (7020)
19.0 (4275)
76.1 (17102)
16.7 (3760)
66.9 (15048)
8.9 (2000)
35.6 (8000)
15 mm or 15M
(5/8" or No. 5)
20mm (3/4")
20mm (3/4")
125mm (5")
11.0 (2475)
44.0 (9900)
26.6 (5982) 106.4 (23931) 24.1 (5415)
96.4 (21671)
13.9 (3130)
55.7 (12520)
20 mm or 20M
(3/4" or No. 6)
22mm (7/8")
22mm (7/8")
170mm (6-3/4")
15.8 (3555)
63.3 (14220)
40.9 (9198) 163.7 (36794) 38.1 (8575) 152.9 (34365) 20.0 (4505)
80.2 (18020)
25mm or 25M
28mm (1-1/8") 28mm (1-1/8") 210mm (8-1/4")
(1" or No. 8)
20.1 (4515)
80.3 (18060) 59.3 (13381) 238.1 (53526) 59.6 (13395) 238.3 (53582) 35.6 (8010) 142.5 (32040)
NOTES: Allowable load values (safety factor 4:1) are recommended for use in force reaction calculations performed by a qualified design professional. Higher values of safety may be
warranted depending upon the actual application and site conditions. Performance values are guidelines for typical, sound base materials. Installation in questionable base material conditions
should be tested to determine actual field performance.Shear loads are based upon typical A193B7 steel hardware. Always refer to the latest product technical data available at www.sika.ca
for application procedures and handling information. To obtain results not listed in the literature refer to the Sika AnchorFix Design Program available on CD or at www.sika.ca.
Per NTSB safety recommendations, the use of adhesive anchors are prohibited in sustained overhead load applications
Allowable Anchor Spacing and Edge Distance
Reduced Anchor
Capacity Distance
(Cmin)
Full Anchor Capacity
Critical Distance (Ccr)
Reduction Factor
SPACING BETWEEN ANCHORS
24 D
8D
0.9
EDGE DISTANCE:
TENSION LOADS
12 D
See following chart
See following chart
SHEAR LOADS – THREADED ROD
12 D
4D
0.21
SHEAR LOADS – SMOOTH DOWELS
12 D
4D
0.21
SHEAR LOADS – REBAR
16 D
4D
0.15
Edge Distance for Tension Values for Anchors in Concrete
Stud Size
(mm)
Minimum Edge
Distance (C min) (mm)
10
38
0.7
12
44
0.66
15
44
0.7
20
44
0.7
22
89
0.7
25
102
0.7
32
127
0.7
DISPENSING TOOLS*
Sika® AnchorFix®-1 & Sika® AnchorFix®-2CA
CARTRIDGE SIZE
TOOL TYPE
275 mL (9.3 fl. oz)
300 mL (10.1 fl. oz)
Reduction
Factor
Sika® AnchorFix®-3CA & Sika® AnchorFix®-4CA
CARTRIDGE SIZE
TOOL TYPE
Most standard manual caulking guns
(eg : Cox. Ascot dispenser, Chilton dispenser)
825 mL (27.9 fl. oz)
250 ml (8.4 fl. oz)
600 ml (20.2 fl. oz)
1500 mL (50.77 fl. oz)
Most competitive manual and pneumatic, dual pistoned
dispensing tools
(eg: Cox Dual Pneumatic dispenser, 300X. Contact Sika’s
Technical Service Department for more information.)
Most competitive pneumatic dual pistoned dispensing tools
(eg: Cox, PPA. Contact Sika’s Technical Service
Department for more information.)
* Please refer to the Anchoring Accessories Catalog
The information, and in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based
on Sika’s current knowledge and experience of the products when properly stored, handled and applied under normal conditions, within their
shelf life. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or
of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or
from any recommendations, or from any other advice offered. The proprietary rights of third parties must be observed. All orders are accepted
subject to our current terms of sale and delivery. Users should always refer to the most recent issue of the Technical Data Sheet for the product
concerned, copies of which will be supplied on request or can be accessed in the Internet under www.sika.ca.
1-800-933-SIKA
Sika Canada Inc.
Ontario
Alberta
601 Delmar Avenue
Pointe-Claire, QC H9R 4A9
Tel.: (514) 697-2610
Fax: (514) 697-3087
6915 Davand Drive
Mississauga, ON L5T 1L5
Tel.: (905) 795-3177
Fax: (905) 795-3192
18131–114th Avenue N.W.
www.sika.ca
Edmonton, AB T5S 1T8
An ISO 9001:2000 certified company
Tel.: (780) 486-6111
Pointe-Claire : ISO 14001:2004 certified EMS
Fax: (780) 483-1580