754 Tack Coat TDS ()

Ro
oyston 754 Low
L
VO
OC Tac
c Coatt
Royston
n 754 Low VOC Tac Coat is a solvent bas
sed, high perfo
ormance elasto
omeric adhesivve. Royston’s ccarefully balancced solvent ble
end
allows fo
or minimized drying time, alon
ng with easy ap
pplication by ro
oller, brush, airlless spray or a
asphalt distributtor.
USES
Applicattion
Ro
oyston 754 Low
w VOC Tac Co
oat is designed
d to be used as
s
a bond coat be
etween the sub
bstrate and the Rosphalt 50
0
wa
aterproof overla
ay.
PHY
YSICAL PROPE
ERTIES
Colo
or
Black
Location
ns
Th
his adhesive can
c
also be us
sed as a highlly effective tac
c
co
oat for bare concrete whe
en Rosphalt is
s the desired
d
ovverlay. The ela
astomeric base
e of Royston 754 Low VOC
C
Ta
ac Coat enhanc
ces the adhesion of Rosphaltt to concrete.
Perccent Solids, by w
weight
47.. 3
Com
mposition
S
Synthetic rubber and resin base
ed
com
mpound in organ
nic solvent syste
em
Visco
osity, sec Zahn
n #3
21 ± 5
Weig
ght, lbs/gal
7.7
73
Cove
erage, gal/sq.yd
d.
SURFA
ACE PREPARA
ATION
The surrface should be
b free of all dust, dirt, oil, grease or otherr
contamiinants. The surface
s
must be completely
y dry prior to
o
applicattion.
MIXING
G
Royston
n 754 Low VOC
C Tac Coat sho
ould be stirred to
t a uniform
consiste
ency prior to us
se.
APPLIC
CATION
Royston
n 754 Low VOC
C Tac Coat ca
an be applied by
b brush, rollerr
or airlesss spray. The airless
a
spray eq
quipment is the
e same as used
d
with solvent containin
ng paints and should produc
ce a 2000 psi
maximu
um pressure. When used with
w
Rosphalt on concrete,
spread with a conve
entional asphalt distributor at
a 0.1 to 0.15
5
gallons per square yarrd in normal spray pattern.
0.10 - 0.15
PACK
KAGING
5 Gall on Pails
55 Ga
allon Drums
STOR
RAGE
Materiials must be kept in a dry area at temperatures betwe
een
C - 35°C) in th
50°F a
and 95°F (10°C
he original uno
opened contain
ners
during
g all phases of delivery, storag
ge and handling.
CAUT
TION
Directt contact with skin should be
e avoided as it can cause skin
s
irritatio
on. Protectivve clothing, goggles an
nd gloves are
recom
mmended. In ca
ase of direct ccontact with the skin, wash with
w
soap and water. In case of accidental contactt with eyes, flush
immed
diately with w
water and see
ek medical atttention. Liquid
d is
flamm
mable, keep awa
ay from open flame.
To avoid solvent entra
apment, a 20-4
40 minute amb
bient (40-60°F))
dry perio
od is recomme
ended prior to th
he placement of
o the overlay.
Construction Products
Conttact Chase C
Global Operations Cen
nter
niversity Avenue
295 Un
Westwo
ood, MA 02090
USA
www.ch
hasecorp.com
T
Toll Free (US onlyy): 800-323-4182
T
Tel: 781-332-070
00
F
Fax: 781-332-070
01
E
Email: [email protected]
Warrantyy & Limitation of Se
eller’s Liability
The inform
mation contained herrein is provided for product
p
selection only, and is not to be considered as a sppecification or perforrmance data. Chase
e Construction Produ
ucts (a division of Chase
Corporation
n) warrants the product for a period of on
ne (1) year from the date of initial shipme
ent to the initial purcchaser, that the produ
ucts meet the param
meters listed on the a
applicable Technical Data
Sheet. Cha
ase makes no warra
anty of any kind, ex
xpressed or implied, including that of merchantability, other than that products conform to Chase’ss current quality control standards at tim
me of
manufacturre. If breach of warra
anty is established, th
he buyer’s exclusive remedy shall be repa
ayment of purchase pprice of the non-confforming product to re
eplace the non-conforming product. The buyer
b
expressly w
waives any claim to additional damages, including without lim
mitation, incidental orr consequential dam ages. Specific condiitions of sale and Ch
hase’s limited warran
nty are set out in detail in
Chase Corrporation Terms and Conditions of Sale.
18611
Page 1 of
o 1