LGarden Balcony Assembly Instruction

BALCONY
ASSEMBLY INSTRUCTIONS
MODEL #0111
Complete Instructions for the Assembly of the
LGarden BALCONY
Mobile Elevated Planter.
LGarden BALCONY Assembly Instructions
Open the BALCONY packaging completely and check the
components against the following list of parts. Be sure all
quantities are correct before beginning.
CONTENTS OF PACKAGE
•
Fixed Wheel End Assembly (1)
•
Stationary End Assembly (1)
•
Side Assembly (2)
•
Crossbars(2)
•
Side Straps (4)
•
Western red cedar boards(4)
•
Screws (33)
•
Nuts (33)
Screws: 8-32 Thread, 3/8" Length, Black-Oxide, Phillips Screw
Nuts: 8-32 Thread, Nylon-Insert Hex Locknut
During assembly you should initially handtighten screws and nuts. After unit is
assembled, go back through and tighten
all screws with tools.
1
2
First assemble Side
Assemblies and End
Assemblies upside
down for ease of
assembly
Take Fixed Wheel
End Assembly and
stand on end
Line up first Side
Panel on the inside of
Fixed Wheel End
Assembly and place
curled edge facing
ground
Insert 4 Screws and
Nuts to fasten first
Side Panel to Fixed
Wheel End Assembly
3
4
Line up second
Side Panel on the
inside of the Fixed
Wheel End
Assembly with
curled edge facing
ground
Insert 4 Screws
and Nuts to fasten
Side Panel to
Fixed Wheel End
Assembly.
Stand Stationary
End Assembly
upside down
opposite Fixed
Wheel End
Assembly
Insert 4 Screws
and Nuts to fasten
both Side Panels
to the inside of
Stationary End
Assembly.
5
6
7
Gently flip unit over
(upright) to finish
assembly
Assemble the two
crossbars together.
Insert 3 screws and
nuts in 3 places One set on each
end and one set in
the middle
Slide assembled
Crossbars to fit into
place in the middle
of the BALCONY
Fasten 4 sets of
screws and nuts (2
sets to each end
tab of the unit)
8
9
10
Fasten each Side
Strap to side of the
unit with screws.
The Straps will
eventually be
fastened to the
bottom of the
Crossbar, but to
start, fasten the
Straps to the
outside of the Side
Panels and rest the
opposite side of
the strap on top of
Crossbar.
After all 4 Straps
are fastened to the
Side Panels, fasten
the Straps to the
Crossbar with the
straps on the
bottom.
Insert 4 sets of
screws and nuts
Insert one last
screw and nut
through both End
Assemblies above
Crossbar.
Tighten all screws and nuts
for final assembly
11
Move LGarden BALCONY to
desired planting location.
Add 4 slots of wood to
the unit. Wood will
need to enter the unit
on an angle to fit
inside.
Place lava rock directly on boards
then place liner on top of rocks & fill with potting mix for best drainage
12
13
Layer the inside of the
bottom “V” of the unit
with Lava Rock –
approximately ½ Cubic
Foot (This will help
ensure proper
drainage).
Unfold the Fabric Liner
and lay it into the
Vessel, covering the
Lava Rock and
reaching it up over the
top of the upper boards
on each side.
Your LGarden BALCONY is now ready for
premium Potting/Container Mix.
TIPS:
• While filling the BALCONY with light-weight Container Mix, hold the Fabric Liner down to
remove all air pockets, and keep it stretched above the top of the Cedar Boards (This will
help contain the soil inside the Planting Vessel).
• Once filled with Container Mix, any excess liner can be cut or away tucked behind the red
cedar boards
Visit
www.elevatedgardening.com
for additional information & upcoming news