851347 Model TLC Chimney - AmeriVent

Transcription

Edition 2
Model TLC
All-Fuel Chimney
Tables of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Certification & Applications . . . . . . . . . . . . . . . . . . . . .2
Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Enhanced Features . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Height Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .2
Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Chimney Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Stainless Steel Locking Bands . . . . . . . . . . . . . . . . . . .3
Chimney Offset Charts . . . . . . . . . . . . . . . . . . . . . . .4-5
Insulated 15°, 30° and 45° Elbows Kits . . . . . . . . . . . .6
Insulated Tee with Tee Cap . . . . . . . . . . . . . . . . . . . . .6
Insulated Tee Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Adjustable Wall Support . . . . . . . . . . . . . . . . . . . . . . . .7
Adjustable Intermediate Wall Support . . . . . . . . . . . . .7
Ceiling Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Cathedral Ceiling Support Box . . . . . . . . . . . . . . . . . . .8
Roof Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
A full line of the finest products is yours
from American Metal Products.
Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . . . .9
Firestop Radiation Shield . . . . . . . . . . . . . . . . . . . . . .10
Firestop/Joist Shield . . . . . . . . . . . . . . . . . . . . . . . . . .10
Rafter Radiation Shield . . . . . . . . . . . . . . . . . . . . . . .10
Black Wall Thimble . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Roof Flashing Selection Chart . . . . . . . . . . . . . . . . . .11
Adjustable Flashing Assembly - Flat to 6/12 . . . . . . .11
Adjustable Flashing Assembly - 6/12 to 12/12 . . . . . .12
Tall Cone Flashing . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Rubber Boot Flashing Kit . . . . . . . . . . . . . . . . . . . . . .12
Galvalume Storm Collar . . . . . . . . . . . . . . . . . . . . . . .13
Silicone Sealant for Storm Collar . . . . . . . . . . . . . . . .13
Deluxe Rain Caps . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Spark Arresters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Wall Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Adjustable Ceiling Plate . . . . . . . . . . . . . . . . . . . . . . .14
Stovepipe Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Soffit Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Matte Black Trim Collar with Brass Trim . . . . . . . . . .15
Adjustable Universal Roof Guy Kit . . . . . . . . . . . . . . .16
Shielding Insulation Wrap . . . . . . . . . . . . . . . . . . . . .16
Anchor Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Decorator Ceiling Support Installations . . . . . . . . . . .17
Wall Support Installation . . . . . . . . . . . . . . . . . . . . . .17
Cathedral Support Installation . . . . . . . . . . . . . . . . . .17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Introduction
Model TLC All-Fuel Chimney offers current technology in
factory-built chimney design by providing superior
performance, durability and safety.
AmeriVent
All-Fuel Chimney - Model HS/HSS
All-Fuel Chimney - Model TLC
Black Stovepipe
Direct Vent
Model CV Special Gas Vent
Model SW Special Gas Vent
Pellet Pipe Plus - Model PVP
Pellet Vent
Type B Gas Vent
AmeriFlex
Flexible Duct Systems
J&J Register
Light Commercial Grilles, Registers & Diffusers
Duct System Components
Lima Register
Residential Grilles, Registers & Diffusers
MODEL TLC ALL-FUEL CHIMNEY
1
Certification & Applications
Construction
Model TLC is safety-tested and listed to
applicable UL safety standards for chimneys
serving solid-fuel and liquid-fuel appliances.
This includes UL 103.
Sizes:
This chimney system is designed for use on appliances
that use solid, liquid or gas fuels under natural draft
conditions.
Allowable flue gas temperatures are:
Type HT
5" to 8"
Maximum Continuous
1000°F
Brief Forced Firing (1 hr.)
1400°F
Creosote Burn-Out (10 min.) 2100°F
Non-HT
10" to 14"
1000°F
1400°F
1700°F
Lifetime Warranty
5" to 14"
Inner Liner (Flue): Type 304 Series Stainless Steel
0.016" thickness
Outer Casing:
Type 304 Stainless Steel
0.015" thickness
Insulation:
The 1" space between the inner/outer
walls is packed with mineral wool fiber
insulation to provide superior insulating
qualities in a slim-line design.
Airspace
Clearance to
Combustibles:
2"
See the written lifetime warranty for all chimney
components on page 18.
Enhanced Features
Model TLC is extremely corrosion-resistant. Both the
inner liner and outer casings are constructed of 304
stainless steel. Embossed couplers do not allow
moisture to penetrate the chimney’s outer wall. Sections
simply twist-lock together and are secured with Locking
Bands. The Model TLC product line features deluxe
chimney support components that will enhance any
installation. Brass trims are used to embellish the
chimney support component parts that may be installed
inside the home.
Embossed Coupler
Prevents moisture
penetration.
Premium Fiber
Insulation
100% mineral wool
(no chlorides).
Supports
All Model TLC supports are designed to carry four
times the UL-listed weight of the listed height.
Height Requirements
The chimney must extend at least three feet above the
highest point where it passes through the roof surface
and at least two feet higher than any part of the
building within a horizontal distance of ten feet.
304 Stainless
Steel Inner Liner
High grade material
heats up quickly to
enhance draft.
Mineral Wool
Insulation
Augured in for better
insulating value to
keep outside
temperatures low for
safety and inside
temperatures high for
performance.
Twist-Lock
Connection
Easy assembly.
304 Stainless Steel
Outer Casing
Premium material
prevents corrosion.
2
Chimney Lengths
• Slim, advanced design allows for installation between 16" centers and still provides 2" clearance
from combustible material.
• Secure twist-lock design couples chimney sections together with just a 1/8 turn. Locking bands
secure joints.
• Includes locking band.
• Sections overlap by 11/8".
• Chimneys are sized according to the inner diameter and are available in 5" through 14".
• The outside diameter is 2" larger than the inside diameter.
Model
Number
5TLC36
5TLC24
5TLC18
5TLC12
5TLC6
6TLC48
6TLC36
6TLC24
6TLC18
6TLC12
6TLC6
7TLC48
7TLC36
7TLC24
7TLC18
7TLC12
7TLC6
8TLC48
8TLC36
8TLC24
8TLC18
8TLC12
8TLC6
Dimensions
Size
5"
6"
7"
8"
Height
A
ID
B
OD
C
36"
24"
18"
12"
6"
48"
36"
24"
18"
12"
6"
48"
36"
24"
18"
12"
6"
48"
36"
24"
18"
12"
6"
5"
5"
5"
5"
5"
6"
6"
6"
6"
6"
6"
7"
7"
7"
7"
7"
7"
8"
8"
8"
8"
8"
8"
7"
7"
7"
7"
7"
8"
8"
8"
8"
8"
8"
9"
9"
9"
9"
9"
9"
10"
10"
10"
10"
10"
10"
Model
Number
10TLC36
10TLC24
10TLC18
10TLC12
10TLC9
10TLC6
12TLC36
12TLC24
12TLC18
12TLC12
12TLC9
12TLC6
14TLC36
14TLC24
14TLC18
14TLC12
14TLC9
14TLC6
Dimensions
Size
10"
12"
14"
Stainless Steel Locking Bands
• Locking bands are used at all
joints for safety and stability.
• Locking band flanges engage the
curl in each end of the adjoining
sections, holding them securely
together.
Height
A
36"
24"
18"
12"
9"
6"
36"
24"
18"
12"
9"
6"
36"
24"
18"
12"
9"
6"
ID
B
10"
10"
10"
10"
10"
10"
12"
12"
12"
12"
12"
12"
14"
14"
14"
14"
14"
14"
OD
C
12"
12"
12"
12"
12"
12"
14"
14"
14"
14"
14"
14"
16"
16"
16"
16"
16"
16"
Dimension
Model
Number
Size
5TLCLB
5"
7"
6TLCLB
6"
8"
7TLCLB
7"
9"
8TLCLB
8"
10"
10TLCLB
10"
12"
12TLCLB
12"
14"
14TLCLB
14"
16"
A
3
Chimney Offset Charts
These charts have three columns for elbow angle required to achieve your desired
offset. The first column (Offset) is the horizontal measurement, at the chimney
centerline, of the offset needed to get around an obstacle. The second column
(Height) is the height of the assembled offset elbow to the top of the return elbow.
Column 3 shows the appropriate Lengths Required.
1. Determine the distance of the offset required.
2. On the chart, find the predetermined distance required for the elbow kit under the
corresponding chimney diameter.
3. After finding the offset, follow across the chart to find the specified height and appropriate chimney lengths
required under their corresponding diameters.
Notes:
• Model TLC chimneys are limited to offsets not exceeding 30°. Combining offsets for greater angle is not permitted.
The 45° elbows may be used only with oil or gas appliances.
• Elbows may be used for interior installation only.
• Never install an elbow in a joist area. Chimney sections must pass vertically through framed joists area.
• Locking bands must be used at all chimney joints.
• Elbow support will support 15 feet of chimney, and the maximum length of chimney allowed between elbows is 6
feet.
• All measurements are in inches.
• Offset tolerances ± one inch.
15° Elbow Offset Chart (inches)
Offset
5"
11/2
21/8
4
51/2
71/2
83/8
101/8
111/4
123/4
143/8
16
19
20
6"
11/8
23/8
4
51/2
7
83/8
101/4
113/8
13
141/2
161/8
173/8
19
-
7"
11/8
23/8
4
51/2
7
83/8
101/4
111/2
13
141/2
161/8
173/8
19
-
8"
11/4
21/2
41/8
55/8
71/8
83/8
101/4
111/2
13
145/8
161/8
173/8
19
-
10"
11/4
21/2
31/4
4
55/8
71/8
101/4
-
Height
12"
1
21/4
3
33/4
53/8
67/8
10
-
14"
1
21/4
31/8
37/8
53/8
7
10
-
5"
9
131/2
191/8
25
301/2
361/2
42
481/4
54
593/4
651/2
761/4
76
6"
10
141/4
201/2
261/4
32
363/4
435/8
483/8
541/8
60
653/4
701/2
761/4
-
7"
101/4
15
203/4
261/2
321/4
37
44
485/8
543/8
601/8
66
703/4
761/2
-
8"
103/8
155/8
21
263/4
321/2
371/4
441/8
487/8
545/8
603/8
661/4
71
763/4
-
10"
91/2
14
167/8
193/4
255/8
313/8
43
-
Lengths Required
12"
73/4
121/4
151/4
181/8
237/8
293/4
411/4
-
14" 6"
81/4 127/8 1
153/4 185/8 241/2 301/4 1
417/8 1
1
-
9"
1
-
12" 18" 24" 36"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
Chimney Offset Charts
Offset
5"
3
51/4
9
111/4
141/4
16
20
217/8
237/8
271/8
303/8
37
42
6"
23/4
51/4
81/4
111/4
141/4
165/8
201/4
225/8
255/8
285/8
315/8
341/8
371/8
-
7"
31/8
55/8
85/8
115/8
145/8
17
205/8
23
26
29
32
341/2
371/2
-
8"
31/2
6
9
12
15
171/8
21
231/2
261/2
291/2
32
35
38
-
10"
37/8
61/4
73/4
91/4
121/4
151/4
211/4
-
Height
12"
37/8
61/4
73/4
91/4
121/4
151/4
211/4
-
14"
41/4
65/8
81/8
91/2
125/8
155/8
211/2
-
5"
10
14
191/4
241/2
293/4
341/8
393/4
441/2
501/8
551/8
605/8
693/8
70
6"
115/8
157/8
21
261/4
313/8
355/8
417/8
46
511/4
563/8
615/8
657/8
71
-
7"
13
171/4
223/8
275/8
327/8
37
431/4
471/2
525/8
573/8
63
671/4
721/2
-
8"
141/2
183/8
24
291/8
323/8
381/2
443/4
49
541/8
593/8
641/2
683/4
74
-
10"
151/8
191/4
217/8
241/2
293/4
347/8
451/4
-
Lengths Required
12"
145/8
183/4
213/8
24
291/8
343/8
443/4
-
14" 6"
155/8 193/4 1
223/8 25
301/8 353/8 1
3
45 /4 1
1
-
9"
1
-
12" 18" 24" 36"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Offset
5" 6" 7" 8"
5
51/4
41/2 1
8
8 /2 83/4
1
12 /8 - 133/8 14
161/2 - 17 161/2
203/4 - 22 211/2
- 253/8 1
30 /4 - 301/2 31
- 331/8 - 37
1
- 41 /4 - 461/2 - 50
- 541/4 58
- 541/2 56
Height
Lengths Required
5" 6" 7" 8" 6"
101/8 - 11 12
1
131/2 - 141/4 15
171/2 - 181/2 91/2 213/4 - 23 241/4 263/4 - 27 271/4 - 315/8 1
5
33 /8 - 341/2 351/2 - 381/8 1
- 423/8 1
- 46 /2 - 517/8 - 561/4 1
- 601/2 1
58 /2 - 611/2 601/4 -
12" 18" 24" 36"
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
5
Insulated 15°, 30° and 45° Elbow Kits
• The insulated elbow is used when offset is required.
• Locking bands must be used on all elbows.
• A maximum of 6 feet is allowable between offsets.
• Elbow is fully insulated and can be used with the same 2-inch
clearance as chimney lengths.
• Elbow support must be used with all offset installations and will
support 15 feet of chimney.
• Elbows do not have twist-locking ridges, so they can be rotated to
attain optimum positioning offset and allow chimney to return to
correct vertical alignment prior to installing locking bands.
• May not be used outdoors.
• 10", 12" and 14" sizes available in 15° and 30° elbow kits only.
• 45° elbows may be used only with oil or gas appliances.
• Elbow kits include:
2 elbows (Exception: 12" and 14" sizes include four 15° elbows
assembled into two 30° elbows)
4 locking bands (Exception: 10", 12" and 14" sizes include two
locking bands)
1 elbow support
All hardware
Model
Number
Size
Dimensions (inches)
A
B*
5TLCEK15
1
2 /2
7
2 /8
3 /16
6"
6TLCEK15
1
2 /2
7
2 /8
37/16
7"
7TLCEK15
21/2
21/16
37/16
8TLCEK15
3
2 /4
3 /16
10" 10TLCEK15
21/2
51/2
12" 12TLCEK15
21/4
2
53/4
6
5"
15°
8"
14" 14TLCEK15
Model
Number
Size
1
C
7
31/2
N/A
N/A
N/A
Dimensions (inches)
A
B
C
3
7
5"
5TLCEK30
3 /4
3 /8
23/4
6"
6TLCEK30
33/4
37/8
31/8
7"
7TLCEK30
41/2
43/8
35/8
8TLCEK30
1
15
4 /16
41/8
10" 10TLCEK30
4 /2
5
43/4
12" 12TLCEK30
4
41/4
31/2
4
14" 14TLCEK30
41/4
41/4
41/4
30°
8"
Model
Number
Size
Dimensions (inches)
A
B
C
45° elbows may be used only
with oil or gas appliances.
45°
6TLCEK45
33/4
N/A
37/8
N/A
115/16
N/A
7"
7TLCEK45
5
8"
8TLCEK45
N/A
51/2
N/A
21/2
N/A
5"
5TLCEK45
6"
*10" to 14" 15° elbows B dimension is total height.
Insulated Tee with Tee Cap
• The insulated
Model
chimney tee
may be used
Number
for through5TLCT
the-wall
installation,
6TLCT
using a wall
7TLCT
support.
8TLCT
• A chimney
10TLCT
length is required to pass safely
12TLCT
through a wall.
14TLCT
• Includes the following:
- Two locking bands
- 5" to 8" sizes have an uninsulated (single-wall) twist-lock tee cap
- 10" to 14" sizes have an insulated press fit tee cap.
Dimensions (inches)
ID
Height
D
B
C
1
5
5
10 /2
1
5
6
11 /2
5 /8
53/4
5"
OD
A
7
6"
8
7"
9
7
121/4
61/4
63/16
8"
10
8
133/8
65/8
61/2
3
3
Size
E
5
10"
12
10
16 /4
8 /8
83/8
12"
14
12
183/4
93/8
93/8
14"
16
14
203/4
103/8
103/8
for non-wall support applications only.
6
Insulated Tee Cap
Model
Number Size
• Permits typical 2" airspace clearance to
combustibles.
• 5" to 8" sizes are twist-lock and
for non-wall support applications
only.
• 10" to 14" sizes are press-fit
design.
Dimensions (inches)
OD
ID
A
B
C
7
5
27/8
8
6
27/8
5TLCITP
5"
6TLCITP
6"
7TLCITP
7"
9
7
27/8
8TLCITP
8"
10
8
10TLCITP 10"
12
10
27/8
N/A
12TLCITP 12"
14
12
N/A
14TLCITP 14"
16
14
N/A
Adjustable Wall Support
• Used to support the chimney on a through-the-wall
installation.
• 5" to 8" sizes include top plate, side brackets,
hardware, non-twist-lock insulated tee cap, and a
long L-bracket to hold tee cap in place.
• 10" to 14" sizes do
not include the cap.
Use tee cap
packaged with tee.
Model
Number
5TLCAWS
6TLCAWS
Dimension (inches)
Size
5"
6"
A
B
C
12
5
10 / 8
7
Adjustability
18 / 8
4
12
5
10 / 8
7
18 / 8
4
5
1
7TLCAWS
7"
13
11 / 8
20 / 2
4
8TLCAWS
8"
14
125/ 8
217/ 8
4
16
5
14 / 8
1
25 / 4
4
19
1
16 / 2
23
21
1
27
10TLCAWS 10"
12TLCAWS 12"
14TLCAWS 14"
18 / 2
• 2" to 6" clearance
away from wall.
• 5" to 8" sizes
support between
30 feet and 74 feet
of chimney, based
on size and
orientation.
See instructions for specific heights.
nonadjustable
Non-Twist-Lock
Insulated Tee Cap
(5" to 8" sizes)
L-Bracket
(5" to 8" sizes)
• 10" to 14" sizes support up to 40 feet of chimney.
• 12" to 14" sizes are nonadjustable supports.
Adjustable Intermediate Wall Support
• Used as supplementary support
when chimney system height
exceeds maximum height allowed
by wall support.
• Supports an additional 38 feet of
chimney.
Model
Number
Size
A
• Includes top plate, support band,
side brackets, and hardware.
6TLCIWS
6"
11
7TLCIWS
7"
12
• 2" to 6" clearance away from wall.
8TLCIWS
8"
13
Dimension (inches)
7
Ceiling Supports
• For use in ceiling support installations.
Model
Number
Dimensions (inches)
Size
A
B
7
3
C
5TLCCSB
5"
16 / 8
11 / 8
63/ 4
6TLCCSB
6"
177/ 8
123/ 8
73/ 4
• Chimney pipe cannot pass below support.
7TLCCSB
7"
187/ 8
133/ 8
83/ 4
• Matte black finish with brass finishing ring, support
gives a premium finished appearance.
8TLCCSB
8"
195/ 8
143/ 8
93/ 4
10"
1
1
101/ 4
• Supports a total of 50 feet of chimney above.
10TLCCS
18 / 2
16 / 4
• Also acts as a firestop.
• Must always use stovepipe adapter. See page 15.
5" to 8" sizes
(painted black)
10" size
(unpainted)
Cathedral Ceiling Support Box
• Used in pitched ceiling support
installations.
• Supports a total of 38 feet of
chimney with up to 15 feet below
support. Includes support clamp,
allowing chimney pipe to pass
below support.
Model
Number
5TLCCS
6TLCCS
7TLCCS
8TLCCS
Dimensions (inches)
Size
A
B
5"
1
7 /8
11
6"
1
8 /8
12
7"
1
9 /8
13
8"
1
14
10 / 8
• Matte black finish with stylish brass
finishing trim and ceiling trim to
cover rough opening.
• Also acts as a firestop with use of trim plate.
• 12/12 maximum pitch.
8
Roof Support
• The roof support may be used
on a floor, ceiling or roof, and
adjusts to any roof pitch.
• It may be used above an offset
to support the offset or as a
supplementary support when
the chimney height exceeds
that of the primary support.
Dimensions (inches)
Model
Number
Size
A
B
5TLCRS
5"
7
16
6TLCRS
6"
8
17
7TLCRS
7"
9
18
8TLCRS
8"
10
19
Model
Number
Size
A
B
10TLCRS
10"
10
12
12TLCRS
12"
12
14
14TLCRS
14"
14
16
• Supports a total of 50 feet of
chimney with up to 20 feet
below support.
Roof Support
• Contains one 18-inch
length of pipe with roof
brackets preinstalled.
Includes hardware.
Dimensions (inches)
• Fits all roof pitches.
Mounts easily on top of
roof.
• Supports a total of 30 feet
with up to 20 feet below the
support.
Attic Insulation Shield
• The attic insulation shield
must be installed where the
chimney enters the attic
space in any installation.
• Designed to keep insulation
away from the chimney and
to maintain the mandatory
2-inch clearance to
combustibles.
• Must be used when the
chimney penetrates an
unoccupied attic.
• Also acts as a firestop.
Dimensions (inches)
Model
Number Size
A
B
C
5TLCIS
6TLCIS
7TLCIS
5"
6"
7"
11
71/ 8
13
12
1
8 /8
14
13
1
9 /8
15
1
8TLCIS
8"
14
10 / 8
16
10TLCIS
10"
16
121/ 8
18
18
1
14 / 8
20
20
1
22
12TLCIS
14TLCIS
12"
14"
16 / 8
• Not to be used for enclosed chimneys.
9
Firestop Radiation Shield
• Required where
the chimney
passes from a
lower living
space into an
upper living
space.
• Maintains the
mandatory 2-inch
clearance to
combustibles.
Firestop/Joist Shield
• Used in floor/ceiling penetrations, other than those that
include a ceiling support.
• Not required when passing through roof.
Dimensions (inches)
Model
Number
Size
A
B
5TLCFRS
5"
13
9
6TLCFRS
6"
14
10
7TLCFRS
7"
15
11
8TLCFRS
8"
16
12
Model
Number
Dimensions (inches)
Size
A
B
C
D
10TLCFRS 10"
1
12 / 8
14
18
16
12TLCFRS 12"
1
14 / 8
16
20
18
14TLCFRS 14"
1
18
22
20
16 / 8
Can be installed in either orientation
Rafter Radiation Shield
• The rafter radiation shield must be installed
immediately below the roof if the chimney is
enclosed.
Dimension (inches)
Model
Number
Size
5TLCRRS
5"
9
6TLCRRS
6"
10
7TLCRRS
7"
11
8TLCRRS
8"
12
A
10
Black Wall Thimble
Model
Number
• Used in a wall support installation.
• Radiation shield is
included with spacers,
which maintain the
mandatory 2-inch
clearance to combustibles.
• Attractive matte black
finishing trim is included
with stylish brass finish.
• Adjustable wall thickness
from 4½" to 8¾" for 5" to
8" sizes and from 6" to 11"
for 10" to 14" sizes.
• 10" to 14" sizes have a
round face plate without
brass trim.
Dimension (inches)
Size
A
B
5"
1
7 /8
16
6"
1
8 /8
16
7TLCWTB
7"
1
9 /8
16
8TLCWTB
8"
101/ 8
16
10TLCWTB 10"
1
12 / 8
18
12TLCWTB 12"
1
14 / 8
20
14TLCWTB 14"
1
24
5TLCWTB
6TLCWTB
16 / 8
Roof Flashing Selection Chart
To determine what roof flashing you’ll require, you must determine the pitch
of the roof. To determine the pitch, you’ll need two rulers and a level.
Measure the number of inches from the end of the level down to the roof.
In this example, the pitch is 3/12.
Adjustable Flashing Assembly - Flat to 6/12 Pitch
• Used where the chimney passes through a roof with a pitch of Flat to 6/12.
• Comes complete with storm collar.
• All seams are sealed with silicone
sealant.
• Galvalume construction.
Dimensions (inches)
Model
Number
Size
A
B
5TLCF6
5"
24
24
6TLCF6
6"
24
24
7TLCF6
7"
24
24
8TLCF6
8"
1
27 / 2
271/ 2
10TLCF6
10"
27
317/ 8
12TLCF6
12"
36
363/ 8
14TLCF6
14"
36
363/ 8
11
Adjustable Flashing Assembly - 6/12 to 12/12 Pitch
• Used where the chimney passes through a roof with a pitch of 6/12 to 12/12.
Dimensions (inches)
Model
• All seams are sealed with silicone
Number Size
A
B
sealant.
1
21 / 2
30
5TLCF12
5"
1
6TLCF12
6"
21 / 2
30
7"
211/ 2
30
8TLCF12
8"
1
21 / 2
30
10TLCF12
10"
36
371/ 2
12TLCF12
12"
36
401/ 2
14TLCF12
14"
36
431/ 2
Model
Number
Size
5TLCFF
5"
24 x 24
6TLCFF
6"
24 x 24
7TLCFF
7"
24 x 24
8TLCFF
8"
24 x 24
10TLCFF
10"
30 x 30
12TLCFF
12"
32 x 32
14TLCFF
14"
34 x 34
• Required where the chimney passes through a corrugated roof.
Model
Number
Size
• Rubber boot flashing fits roof pitches up to 12/12.
TLCRBF 5" - 8"
7TLCF12
Tall Cone Flashing
• 0/12 to 2/12 pitch.
• All seams are sealed with silicone sealant.
Dimensions (inches)
A
Rubber Boot Flashing Kit
• This kit fits 5", 6", 7" and 8" chimneys.
• Kit includes: Special Storm Collar
Rubber Boot
Spacer Kit
Special Boot-Mounting Screws
• UL-listed.
12
Galvalume Storm Collar
• Used in conjunction with roof flashing to keep precipitation out.
Silicone Sealant for Storm Collar
• Used to seal storm collar to chimney length above cone of flashing.
Model
Number
Dimensions (inches)
Size
A
5TLCSC
5"
7
41/ 2
6TLCSC
6"
8
41/ 2
7TLCSC
7"
9
41/ 2
8TLCSC
8"
10
41/ 2
10TLCSC
10"
12
51/ 2
12TLCSC
12"
14
51/ 2
14TLCSC
14"
16
51/ 2
B
Model
Number
TLCSS
• 3-ounce tube.
Deluxe Rain Caps
• Advanced design, premium quality stainless steel.
• Provides protection against the elements.
• Twist-lock connection for secure installation.
Model
Number
A
B
C
1
5TLCC
5"
5
7 /2
111/ 4
6TLCC
6"
6
8
111/ 4
7TLCC
7"
7
71/ 2
131/ 4
8TLCC
8"
8
8
141/ 4
10TLCC
10"
10
81/ 2
20
12TLCC
12"
12
10
24
14
1
28
14TLCC
5" to 8"
Dimensions (inches)
Size
14"
11 / 2
10" to 14"
13
Spark Arresters
• For use with 6" to 14" caps.
Wall Band
• Stainless steel
construction.
• Provides lateral
support for the
chimney when
installed adjacent
to a wall.
• Maintains the mandatory 2-inch
clearance to combustibles.
• Used 4 feet above the tee, then
every 8 feet thereafter.
Adjustable Ceiling Plate
• Matte black finish.
• Adjusts to multiple roof pitches.
• Covers 2-inch space around chimney for attractive finish.
Model
Number
Size
6TLCSA
6"
7TLCSA
7"
8TLCSA
8"
10TLCSA
10"
12TLCSA
12"
14TLCSA
14"
Model
Number
Size
A
B
5TLCWB
5"
7
17
6TLCWB
6"
8
17
7TLCWB
7"
9
17
8TLCWB
8"
10
17
10TLCWB
10"
12
17
12TLCWB
12"
14
17
14TLCWB
14"
16
17
Dimensions (inches)
Flat to 6/12 Pitch
Model
Number
Dimensions (inches)
Size
A
B
5TLCACP
5"
18 to 29
151/2
6TLCACP
6"
19 to 30
161/2
7TLCACP
7"
20 to 31
171/2
8TLCACP
8"
21 to 33
181/2
10TLCACP
10"
23 to 37
201/2
12TLCACP
12"
25 to 41
221/2
14TLCACP
14"
27 to 45
241/2
6/12 to 12/12 Pitch
Model
Number
Dimensions (inches)
Size
A
B
5TLCACPT
5"
18 to 29
151/2
6TLCACPT
6"
19 to 30
161/2
7TLCACPT
7"
20 to 31
171/2
8TLCACPT
8"
21 to 33
181/2
10TLCACPT
10"
23 to 37
201/2
12TLCACPT
12"
25 to 41
221/2
14TLCACPT
14"
27 to 45
241/2
14
Stovepipe Adapter (stainless steel)
• For quick and easy transition from
black stovepipe to factory-built
chimney.
• Twist-lock for easy connection.
• 5" to 8" is black.
Model
Number
Dimensions (inches)
Size
A
B
C
5TLCSPA
5"
7
5
6
6TLCSPA
6"
8
6
6
7TLCSPA
7"
9
7
6
8TLCSPA
8"
10
8
6
10TLCSPA
10"
12
10
3
12TLCSPA
12"
14
12
3
14TLCSPA
14"
16
14
3
Soffit Plate
• Used where the chimney passes
through a soffit to provide a finished
appearance.
• Maintains the
mandatory 2-inch
clearance to
combustibles.
Model
Number
Dimensions (inches)
Size
A
1
B
5TLCSP
5"
7 /8
13
6TLCSP
6"
81/ 8
14
7"
1
9 /8
15
8"
1
16
7TLCSP
8TLCSP
10 / 8
Matte Black Trim Collar with Brass Trim
• Used on wall support installations when passing through a
noncombustible wall.
• Matte black finish with brass trim for an enhanced hand-crafted
appearance.
Dimensions (inches)
Model
Number
Size
A
5TLCTCB
5"
71/ 8
6TLCTCB
6"
81/ 8
7TLCTCB
7"
91/ 8
8TLCTCB
8"
101/ 8
15
Adjustable Universal
Roof Guy Kit
Model Dimensions (inches)
Number
A
• Used when more than 5 feet of chimney extends
from the roof.
• The kit includes two rods and an adjustable band.
7 to 16
TLCRGK
• Each rod extends to 4 to 6 feet.
• The adjustable band will fit 5" to 14" size chimney.
Shielding Insulation Wrap
• Insulation for use with Attic
Insulation Shield, Wall Thimble and
Cathedral Ceiling Support Box.
• Protects building materials against
radiant heat from the chimney.
• Helps maintain temperatures within
the chimney system and within the
housing envelope to prevent
condensation on exterior.
• UL-listed.
Anchor Plate
• To be used with specifically listed zero-clearance
fireplaces for direct connection of all-fuel chimney.
• 5" to 8" sizes are 14-gauge galvanized base plate, and
10" to 14" sizes are 10-gauge galvanized base plate.
Model
Number
Roll
Size
TLCSI
12" x 46" x 2"
Dimensions (inches)
Model
Number
Size
A
5TLCAP
5"
7
115/ 8
6TLCAP
6"
8
115/ 8
7TLCAP
7"
9
115/ 8
8TLCAP
8"
10
115/ 8
10TLCAP
10"
12
131/ 4
12TLCAP
12"
14
151/ 4
14TLCAP
14"
16
171/ 4
B
16
Decorator Ceiling Support Installations
One-Story Installation
Wall Support Installation
Through a Soffit
Two-Story Installation
Cathedral Support Installation
With Cathedral Ceiling Support Box
17
WARRANTY
LIMITED LIFETIME WARRANTY
American Metal Products Group (“we,” “us,” “our”) warrants chimney and venting products to be free from defects in
material and workmanship for as long as the original consumer owns the system. For products installed after January 15,
2007, for a period of ten (10) years from original installation, we will provide replacement product with a similar or like
quality of available product, free of charge excluding any installation costs. From the eleventh (11th) through fifteenth
(15th) years, we will provide replacement product to the original consumer at a cost of 75% off the published retail price in
effect on the date the claim is received, excluding any installation costs. At expiration of the fifteen- (15) year term, we will
provide replacement product to the original consumer at a cost of 50% off the published retail price in effect on the date the
claim is received, excluding any installation costs.
LIMITATIONS:
- Products must be installed for their intended purpose.
- Products must be connected to residential appliance listed with an accredited testing laboratory.
WARNING: FAILURE TO INSTALL PRODUCTS ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS WILL VOID
ALL APPLICABLE WARRANTIES AND MAY RESULT IN FIRE, CARBON MONOXIDE POISONING OR DEATH. SEE
OUR PRODUCT INSTALLATION INSTRUCTIONS FOR COMPLETE INSTRUCTIONS.
WARRANTY COVERAGE:
All lengths, tees and elbows, and components are applicable to warranty coverage.
THIS LIMITED WARRANTY DOES NOT COVER:
(a) any nonstainless base tee unit mounted or connected to an insulated chimney system;
(b) costs (labor or otherwise**) associated with either removing a previously installed product, installing a replacement
product, transportation or return of a product, or transportation of replacement product;
(c) damage to the finish of products caused by the use of improper solvents/chemicals or improper cleaning methods;
(d) damage resulting from failure to reasonably clean, care for, or maintain products in accordance with our installation
instructions/recommendations;
(e) damage (to products, appliances or structure) based on or resulting from improper installation or repair, misuse or
abuse (including, but not limited to, excessive or improper operating condition), or alteration or adjustment other than in
conformity with our installation instructions and specifications, whether performed by a contractor, service company,
technician, or yourself;
(f) any products that have been moved from their original installation site;
(g) damage caused by burning driftwood, garbage, or any other prohibitive material in the appliance served by the
chimney;
(h) damage that results from accidents such as fire, flood, high winds, “acts of God,” or any other contingency beyond our
control.
**Due to the wide variance in installation practices and other conditions beyond our control, we do not
guarantee or in any way warrant the installation of chimney and venting products.
CLAIM PROCEDURE:
If you believe that a product is defective, notify us in writing at the following location.
American Metal Products Group
Attn: Warranty Claims
5030 Corporate Exchange Blvd. SE
Grand Rapids, MI 49512
800.423.4270 phone
800.626.3825 fax
www.americanmetalproducts.com
Notification should include a description of the product, model and serial number (if applicable), and a description of the
product defect. Upon receipt of a written claim under this limited warranty and evidence of the date of purchase or
installation, at our option and in our sole discretion, we will provide replacement product with similar or like quality of
available product excluding any installation costs. We reserve the right to inspect or investigate any warranty claims prior
to determining whether to provide replacement product. If, as determined by us that repair or replacement of the product is
not commercially practicable or cannot be completed in a timely manner, we may refund the prorated purchase price paid
for the product upon verification by providing a copy of your invoice or receipt of bill of sale.
18
ALL-FUEL CHIMNEY
MODEL HS/HSS
ALL-FUEL CHIMNEY
MODEL TLC
BLACK STOVEPIPE
DIRECT VENT
MODEL CV
SPECIAL GAS VENT
MODEL SW
SPECIAL GAS VENT
PELLET PIPE PLUS
MODEL PVP
PELLET VENT
TYPE B GAS VENT
©2008 American Metal Products Group All rights reserved
Form No. 851347 5M 01/2008
Printed in USA

851347 Model TLC Chimney - AmeriVent

Transcription

Similar documents

chimney repairs - BEROA Deutschland GmbH

Botallack to Land`s End

11230 CHIMNEY ROCK ROAD Paso Robles, CA 93446 Vineyard

Blue Ridge Frontier - Gorilla Dealer Portal

Wood Heat The Safe Way - Farm Bureau Insurance of Michigan

Atlantis Energy Systems Inc.

Chimney Cowls - FlueSupplies.com

TLC SPRING RECESS 2015