RapiScan - Kabs Healthcare (P) Ltd.

Transcription

RapiScan - Kabs Healthcare (P) Ltd.
RapiScan
Leptospira IgG/M Device Rapid Test
INTENDED USE:
This Leptospirosis IgM and IgG Combo Rapid Test is a qualitative test for the detection of IgM and IgG antibodies to leptospirosis virus in human serum or plasma . The test
provides a differential detection of anti-leptospirosis IgM and anti-leptospirosis-IgG antibodies and can be used for the presumptive distinction between a primary and secondary
leptospirosis infection. This test is for in-vitro diagnostic use only.
TEST PRINCIPLE:
Serum or plasma samples may be used with this test. When a specimen is added to the test, IgG and IgM antibodies in the specimen sample react with red particles coated with
leptospirosis proteins. As this specimen/particle mixture migrates along the length of the test, the anti-leptospirosis IgG or IgM antibody particle complex is captured by the relevant
IgG and/or IgM test bands located in the test device window causing a light pink to dark red band to form at the IgG or IgM region of the test device window. The intensity of the
bands will vary depending upon the amount of antibody present in the sample. The appearance of any color in a specific test region (IgG or IgM) should be considered as positive
for that particular antibody type (IgG or IgM). A red procedural control line should always develop in the test device window to indicate that the test has been performed properly.
PRECAUTIONS:
1.
Do not use the test devices or wash buffer beyond the stated expiration date marked on the package label.
2.
Store the test kits and reagents according to the temperature range stated on the package label.
3.
All test devices, wash buffer and specimens must be at room temperature (15-30°C) before running the assay.
4.
Do not re-use the test devices or buffer.
STORAGE AND SHELF LIFE OF REAGENTS:
Store the kit between 2°C and 30°C. Do not store the kit in direct sunlight. Be sure to open only the number of devices to be used. Once the device pouch has been opened, the
test device should be used immediately. The test kit may be used until its expiration date, which can be found on the package label.
KIT COMPONENTS:
Each kit contains the following components in sufficient quantities to perform the number of tests indicated on the package label:
•
25 test devices packaged in individual foil pouches. Each device contains two (2) test lines: one that captures human IgG antibodies and another that captures IgM
antibodies. The device also contains a third procedural control line.
•
1 Product Insert
•
1 Dropper bottle of 3mL Leptospirosis Wash Buffer
TEST PROCEDURE:
1.
Remove the appropriate number of Leptospirosis Combo Test Device pouches from the kit box. Tear open the foil pouch(es) and remove the device(s). Lay the test
device(s) on a clean, flat work surface.
2.
Add 5-10uL of Sample and add 1 – 2 drops of Leptospirosis buffer to the sample well of the cassette
3.
Read the test result after 15 to 30 minutes. Negative results must be confirmed after 30 minutes. Do not read results after 45 minutes.
INTERPRETATION OF THE RESULTS:
1.
The test is not valid if the red control line does not appear, regardless of the presence of a red IgM or IgG line. Repeat the test with a new device.
2.
Specimens with positive IgM antibodies will generate a red line in the control region and a red line in the IgM region. (a blue line next to the “1”)
3.
Specimens with positive IgG antibodies will generate a red line in the control region and a red line in the IgG region. (a blue line next to the “2”)
4.
Specimens with positive IgG and IgM antibodies will generate a red line in the control region and red lines in the IgG and IgM regions.
5.
Positive results may appear as early as 5-10 minutes. Negative results must be confirmed after 30 minutes.
6.
The results are stable for up to 45 minutes. Do not read the results after 45 minutes.
C
C
T
2 1
C
2
1
T
2 1
Sample Well
Control
IgG
IgM
C
C
Control
IgG
IgM
C
2
1
T
2 1
Sample Well
C
C
Control
IgG
IgM
C
2
1
T
2 1
Sample Well
C
C
C
2
1
Control
IgG
IgM
Sample Well
IgM Positive.
The control line (red line) and IgM line red line adjacent to the “1” are visible in the test device window. The test is positive for IgM antibodies. This is indicative of a primary
leptospirosis infection (see the “Expected Values and Limitations” sections).
KABS HEALTHCARE (P) LTD., 69/6A, RAMA ROAD,
OPP. KLJ HOUSE, NEW DELHI-110015
RapiScan
Leptospira IgG/M Device Rapid Test
IgG Positive
The control line (red line) and IgG line (red line adjacent to the “2”) are visible in the test device window. The test is positive for IgG antibodies. This mat be indicative of a
secondary leptospirosis infection (see the limitations section).
IgM and IgG Positive.
The control line (red line), IgM and IgG lines (both red lines) are visible in the test device window. The test is positive for IgM and IgG antibodies. This is indicative of a secondary
leptospirosis infection (see the “Expected Values and Limitations” sections).
Negative Test Result
The control line is the only line visible in the test device window. No IgG or IgM antibodies were detected. The result does not exclude leptospirosis infection. If symptoms persist,
a new sample should be drawn from the patient in 3-5 days and then retested.
Invalid Test Result.
If the control line (red line) does not appear in the test device window, the test results are INVALID regardless of the presence or absence of lines in the IgG or IgM region of the
device window. Repeat the test using a new device.
C
C
1
2
T
T
C
2
1
2
Sample Well
Invalid Result
Control
IgG
IgM
C
C
1
C
2
1
Invalid Result
T
Sample Well
Sample Well
Control
IgG
IgM
C
2
T
C
2
1
2
Control
IgG
IgM
C
1
C
C
1
C
2
1
Control
IgG
IgM
Sample Well
Invalid Result
Invalid Result
LIMITATIONS OF THE TEST:
1.
This test detects the presence of antibodies to leptospirosis in the specimen and should not be used as the sole criterion for the diagnosis of a leptospirosis viral infection.
2.
In early infections and some secondary infections, detectable levels of IgM antibodies may be low. Some patents may not produce detectable levels of antibody within the
first seven to ten days of infection. If symptoms persist, a fresh sample should be drawn from the patient 3-5 days after the first testing date and the new specimen should
be retested.
3.
As with all diagnostic tests, the result must be correlated with clinical findings. If the test result is negative and a leptospirosis infection suspicion still exists, additional
follow-up testing using other clinical methods is recommended.
4.
A negative serological result at any time does not preclude the possibility of an early infection of Leptospirosis v irus.
5.
The use of icteric or lipemic samples should be avoided.
STABILITY:
This Leptospirosis IgG/IgM combo test has been found to be stable for up to 22 months from the date of manufacture when stored between 2 to 30°C. The expiration date of each
test can be found on the kit box label. No component or reagent of the test should not be used beyond its printed expiration date.
1.
References:
Kelly PW. Leptospirosis. In, Infectious disease in medicine and surgery. Gorbach S, Bartlett J, Balcklow N, (eds): Philadelphia, Saunders, 1991, pp.1295-1302.
2.
Ribeiro MA, Assis CSN, Romero EC. Serodiagnosis of human leptospirosis employing immunodominant antigen. Serodiagn. Immunother. Infect. Disease 1994; 6:140-144.
3.
Turner LH. Leptospirosis II. Trans. Royal Soc. Trop. Med. & Hygiene 1968; 62:880-889.
4.
Pappas MG, Ballou WR, Gray MR, et. al. Rapid serodiagnosis of leptospirosis using the IgM-specific dot-ELISA: Comparison with the microscopic agglutination test. Am J
Trop Med Hyg 1985; 34(2):346-354.
5.
Alder B, Murphy AM, Locarnini SA, et.al. Detection of specific anti-leptospiral immunoglobulin M and immunoglobulin G in human serum by solid phase enzyme-linked
immunosorbent assay. J. Clin. Micro 1980; 11:452-457.
KABS HEALTHCARE (P) LTD., 69/6A, RAMA ROAD,
OPP. KLJ HOUSE, NEW DELHI-110015