ALLOYSolv (Part A) MSDS

ALLOYSolv
DATE OF ISSUE: June 2012
PAGE 1 OF 5
MATERIAL SAFETY DATA SHEET
Hazardous According to the Criteria of NOHSC
Section I - IDENTIFICATION OF THE MATERIAL AND SUPPLIER
Product Name:
Other Name:
Manufacturer’s Product Code:
Recommended Use:
ALLOYSOLV
None
KT-CC-ALS
SOLVENT COMPONENT OF ALLOY SYSTEM
Supplier Name:
Supplier Address:
KLEENTEK ADVANCED CLEANING TECHNOLOGIES
10/100 SUGAR ROAD
MAROOCHYDORE, QLD, 4558
07 5443 6020
07 5443 6021
07 5443 6020
www.kleentek.net.au
Telephone No.:
Fax No.:
Emergency No.:
Website:
Section 2 - HAZARDS IDENTIFICATION
Hazard Designation:
Hazardous According to the Criteria of NOHSC
Hazard Category:
Harmful
Risk phrases:
R20/22 – Harmful by inhalation and if swallowed
Safety phrases:
S2: Keep out of reach of children.
S26: Inn case of eye contact, rinse immediately with plenty of water and contact a doctor or
Poisons Information Centre.
In-Use Hazards:
An in-use solution of less than 25% is not classified as hazardous according to the
criteria of NOHSC Australia
Section 3 - COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT
BENZYL ALCOHOL
SURFACTANTS
CAS NUMBER
100-51-6
PROPORTION (W/W)
Greater than 60%
1 to 10%
Section 4 - FIRST AID MEASURES
IF POISONING OCCURS, IMMEDIATELY CONTACT A DOCTOR OR POISONS INFORMATION CENTRE (TELEPHONE
AUS: 13 11 26, NZ: 03 474 7000), AND FOLLOW THE ADVICE GIVEN. SHOW THIS MATERIAL SAFETY DATA SHEET
TO A DOCTOR.
ALLOYSolv
DATE OF ISSUE: June 2012
PAGE 2 OF 5
Inhalation:
Open all doors, windows and/or vents. Move victim to fresh air. Apply resuscitation if victim is not
breathing – If trained personnel available administer oxygen if breathing is difficult.
Skin Contact:
If material is splashed onto the skin, remove any contaminated clothing and wash skin thoroughly
with water and soap if available. If irritation persists transport to hospital or doctor.
Eye contact:
If material is splashed into eyes, immediately, flush with plenty of water for 15 minutes, ensuring eye
lids are held open. If irritation persists transport to hospital or doctor.
Ingestion:
If swallowed, DO NOT induce vomiting, unless instructed to do so by trained health professional.
Transport to hospital or doctor.
First Aid Facilities:
Eye wash fountain, safety shower and normal wash room facilities.
Symptoms:
Not available
Medical attention:
Treat symptomatically
Section 5 - FIRE FIGHTING MEASURES
Fire/Explosion Hazard:
If safe to do so, move undamaged containers from fire area. Hazardous Decompostion Products: May decompose on
heating emitting soot, smoke and decomposition products. Fire Fighting Procedures Fire fighters to wear Self-contained
breathing apparatus (SCBA) in confined spaces, in oxygen deficient atmospheres or if exposed to products of
decomposition. Full protective clothing is also recommended. Extinguishing Media: Use extinguishing media suitable for
surrounding fire situation.
Flammability:
This material is not a flammable or combustible liquid.
Section 6 - ACCIDENTAL RELEASE MEASURES
Ventilate area. Remove all unnecessary personnel from spill area. Wear protective equipment to prevent skin and eye
contact, as outlined under personal protection in this MSDS. Contain using sand or soil - prevent run off into drains and
waterways. Use absorbent (soil, sand, vermiculite or other inert material). Do not use sawdust. Collect and seal in properly
labelled containers for disposal.
Disposal: For disposal information contact the State Land Waste Management Authority or the Environmental Protection
Agency.
Section 7 - HANDLING AND STORAGE
Store in a cool place and out of direct sunlight. Store away from sources of heat or ignition, strong acids, combustibles and
oxidizing agents. Store in original packages as approved by manufacturer. For further information please refer to the
Engineering Controls of this MSDS.
Section 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION
ALLOYSolv
DATE OF ISSUE: June 2012
PAGE 3 OF 5
Exposure Standards:
No exposure standards have been assigned by [NOHSC] for this product or any of the components
Engineering Controls:
Maintain adequate ventilation at all times. In most circumstances natural ventilation systems are adequate unless the
material is heated, reacted or otherwise changed in some type of chemical reaction, then the use of a local exhaust
ventilation system is recommended.
Personal Protective Equipment:
GLOVES: PVC, Nitrile, Neoprene, Natural rubber or any other type of glove are recommended.
EYES: Chemical goggles or faceshield to protect eyes.
RESPIRATORY PROTECTION: Avoid breathing of vapour or mist. Select and use respirators in accordance with AS/NZS
1715/1716.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
Appearance:
Boiling Point:
Vapour Pressure:
Specific Gravity:
Flash Point:
Flammability Limits:
Solubility in Water:
Other Properties:
Clear colourless liquid
205 deg. C (approx.)
Not known
1.04
101 deg. C
Not known
Insoluble
pH 1% 10.0
Section 10 - STABILITY AND REACTIVITY
Chemical Stability:
Hazardous Decomposition Products:
Hazardous Polymerization:
Incompatibilities:
Conditions To Avoid:
Stable under normal conditions of use.
Emits choking and corrosive fumes when heated to decomposition.
Will not occur
Oxidizing agents
Heat, flames, ignition sources and incompatibles.
Section 11 - TOXICOLOGICAL INFORMATION
No adverse health effects are expected, if the product is handled in accordance with this Material Safety Data Sheet and the
product label. Symptoms and effects that may arise if the product is mishandled and overexposure occurs are:
ACUTE HEALTH EFFECTS
ALLOYSolv
DATE OF ISSUE: June 2012
PAGE 4 OF 5
Swallowed:
Harmful if swallowed. May cause irritation to mouth, throat and stomach with effects including mucous build up, irritation to
the tongue and lips and pains in the stomach.
Eye:
May cause irritation to the eyes, with effects including: tearing, pain, stinging and blurred vision.
Skin:
May cause irritation to the skin, with effects including; Redness and itchiness.
Inhaled:
Harmful if inhaled. May cause irritation to the nose, throat and respiratory system with effects including: Dizziness, headache
and possible confusion.
Chronic:
Prolonged or repeated exposure may lead to irreversible damage to health.
Section 12 - ECOLOGICAL INFORMATION
This substance may cause long term adverse effects in the aquatic environment.
Section 13 - DISPOSAL CONSIDERATIONS
Whatever cannot be saved for recovery or recycling should be handled as hazardous waste and sent to an approved waste
facility. Processing, use or contamination of this product may change the waste management options. State and local
disposal regulations may differ from federal disposal regulations. Dispose of container and unused contents in accordance
with federal, state and local requirements.
Section 14 - TRANSPORT INFORMATION
UN Number:
Proper Shipping Name:
Dangerous Goods Class:
Subsidiary risk:
Packing Group:
Hazchem Code:
None allocated
None Allocated
None allocated
None allocated
None allocated
None allocated
Not classified as a Dangerous Good according to the UN, DOT(US), WHIMS, IACO(IATA) or IMO(IMDG).
Non Dangerous Good according to the ADG Code (6th Edition) .
Section 15 - REGULATORY INFORMATION
Poison Schedule:
Inventory Status:
HSNO NZ Classification
None allocated
Australia (AICS) All ingredients are on the inventory.
6.1D
8.2B
6.5B
9.1D
9.2B
9.3C
Solvents, Subsidiary Hazard
ALLOYSolv
DATE OF ISSUE: June 2012
PAGE 5 OF 5
Section 16 - OTHER INFORMATION
Trademark information:
Preparation information:
New product MSDS, Reason for update: New, and conversion to 16 heading format.
Data sources:
This MSDS summarises our best knowledge of the health and safety hazard information of the product and how to safely
handle and use the product in the workplace. Each user should read this MSDS and consider the information in the context
of how the product will be handled and used in the workplace including in conjunction with other products. If clarification or
further information is needed to ensure that an appropriate risk assessment can be made, the user should contact this
company. Since methods and conditions are beyond our control Eco Precision Cleaning and its associated companies does
not accept liability for any damages resulting from the use of, or reliance on, this information in inappropriate contexts.
Revision Date: June 2012
Supersedes : May 2012
END OF MSDS