Z806, Z812, Z812B and Z825B Z800 Series Motorized DC Servo

Z806, Z812, Z812B and Z825B
Z800 Series Motorized DC Servo
Actuator
Operating Manual
Issue 7
Page 1
Table of Contents
Part 1.
Product Warnings ............................................................................ 4
Part 2.
Overview ........................................................................................... 5
Part 3.
Specifications .................................................................................... 6
Part 4.
Wiring Diagrams .............................................................................. 7
4.1.
Connector Pin Assignments ............................................................................ 7
4.2.
Description of connections .............................................................................. 7
Part 5.
Compatible Drivers .......................................................................... 9
Part 6.
Maintenance ..................................................................................... 9
Part 7.
Regulatory ...................................................................................... 10
Part 8.
Thorlabs Worldwide Contacts ...................................................... 11
Page 2
Table of Figures
Figure 1:
Page 3
Output connector ............................................................................................ 7
Part 1. Product Warnings
Safety Warning
These Motorized Actuators can generate high forces. If handled improperly, they may
cause injury. Be aware that failure of the motor controller may drive the unit into a
hard stop and cause damage to the unit.
To avoid injury never put anything in the gap between the Actuator and any rigid
structure.
Caution
If the actuator encounters a hard stop while still in the middle of its range (i.e. a
translation stage at the end of its travel range), the motor should be stopped as soon
as possible to prevent damage to the gear head or motor and to keep the unit from
overheating.
When the Z8 motors are fitted to certain optomech products e.g. the GNL series
Goniometers, it is possible that the motor will reach the mechanical hardstops of the
stage before the motor limit switches are activated. In this case, DO NOT continue to
drive the motor into the hardstop as this will damage the motor. As a guide, the total
current drawn should not exceed 80 mA.
Caution
The control PC used to operate the driver for the Z8 series actuators must be running
APT Software version 2.8 or higher.
Earlier versions of software do not support this product.
Caution
When storing these units, be sure to fully retract the lead screw to protect the threads
from damage. Improper connection of the motor will result in permanent damage. All
power supplied to the motor should be turned off before altering any connections to
the motor. Check all connections before supplying power to the motor .
Page 4
Part 2. Overview
Thorlabs has developed this series of high-resolution motorized actuators for use in
high precision applications. From drop-in replacements to custom mounts, these
motorized actuators will satisfy even the most demanding requirements. Three
different travel lengths are offered; 6.0 mm, 12.0 mm and 25.0 mm.
The Z812B and Z825B actuators are shipped with a clamping bush fitted, ready for
use with a 3/8” barrel mount. The Z806 and Z812 actuators thread into a ¼” -80
mounting bush.
The Z800 series Motorized Actuators use a 12V DC servomotor that provides
sufficient torque for high load capabilities. Utilizing a 67:1 gear reduction head and a
512 counts per rev precision encoder gives a minimum resolution of 29 nm. The
actuators allow very small step sizes over the entire travel range, delivering greater
flexibility with negligible backlash and fine resolution. The DC servomotor allows for
continuously variable speeds while the optical encoder allows closed loop operation.
The actuators use integrated hard stops that automatically cut the power when they
have reached their mechanical limits.
The Z800 series Motorized Actuators are light, compact, and extremely durable. They
are ideal for use in mirror mounts, translation stages, microscopes, OEM applications,
and a wide variety of other components that require higher precision than most
standard drive mechanisms allow.
Page 5
Part 3. Specifications
Item #
Travel Range
Z806
Z812 and Z812B
Z825B
6 mm
12 mm
25 mm
Gear reduction
67:1
Lead screw pitch
Feedback
1.0 mm
Motor mounted rotary encoder
512 counts/rev of the motor
34,304 counts/rev of leadscrew
Limit switches
Electromechanical
Motor type
12 V DC Servo
Backlash
<8 µm
Axial load capacity
Speed range
9 kg
50 µm/sec to 3.0 mm/sec
Calculated Resolution*
29 nm
Operating Temperature
-4 to 149 °F (-20 to 65 °C)
Cable Length
1.6 ft (0.5 m)
Connector
Compatible Controller
HDDB15
TDC001 T-Cube DC Servo Controller
* Calculated Resolution. Actual resolution will depend on the applied load.
How to Calculate the Linear Displacement per Encoder Count
For the Z806, there are 512 encoder counts per revolution of the motor. The output
shaft of the motor goes into a 67:1 planetary gear head. This requires the motor to
rotate 67 times to rotate the 1.0 mm pitch lead screw one revolution. The end result is
the lead screw advances by 1.0 mm.
To calculate the linear displacement of the actuator per encoder count:
512 x 67 = 34,304 encoder counts per revolution of the lead screw
Linear displacement of the lead screw per encoder count is:
1.0 mm / 34,304 counts = 2.9 x 10-5 mm (29 nm)
Page 6
Part 4. Wiring Diagrams
4.1.
Connector Pin Assignments
Figure 1: Output connector
Pin
4.2.
Description
Pin
Description
1
Ground (Limit and Vcc)
9
Ident Resistor
2
Forward Limit
10
Vcc (+5 V DC)
3
Reverse Limit
11
Encoder Channel A
4
Reserved For Future Use
12
Reserved For Future Use
5
Motor (-)
13
Encoder Channel B
6
Reserved For Future Use
14
Reserved For Future Use
7
Motor (+)
15
Reserved For Future Use
8
Reserved For Future Use
Description of connections
Motor (+)
This supplies a +12 VDC supply to the motor of the actuator. The maximum current is
80 mA.
Vcc
A connection should be made to a +5 VDC supply to power both channels A and B on
the encoder.
Page 7
Channels A and B
The Z800 series actuators use a Hall Effect encoder. Both channels A and B are
supplied by the 5 V DC connection.
GND
This is the ground connection for the encoder.
Motor (-)
This supplies a -12 VDC supply to the motor of the actuator. The maximum current is
80 mA.
Limit Ground
This is a common ground for both the forward and reverse limit switches.
Reverse Limit
The reverse limit prevents over driving of the actuator at its minimum extension.
Forward Limit
The forward limit prevents over driving of the actuator at its full extension.
Note.
When a limit switch is activated, the switch makes contact, and the associated output
line is high (5 V).
Page 8
Part 5. Compatible Drivers and Software
The Thorlabs compatible controller for this product is the T-Cube Single Channel DC
Servo Controller TDC001 with firmware 2.0.10 or higher. The use of these controllers
ensures optimal performance. All above performance specifications are guaranteed
only with use of Thorlabs controllers and drivers.
Furthermore, the control PC used to operate the driver must be running APT Software
version 2.8 or higher. Earlier versions of software do not support this product.
Part 6. Maintenance
Periodic greasing of the lead screw is advised, particularly in applications with a high
duty cycle. Grease the lead screw thread as follows whenever the thread appears dry
or the motor is noisy:
1.
Drive the motor to extend the leadscrew to its full extent.
2.
Apply a thin bead of high load, silicon free lubricant (e.g. Apiezon 100) as
shown below.
3.
Drive the motor to retract the lead screw and distribute the grease.
4.
Remove access grease using a lint free cloth.
Page 9
Part 7. Regulatory
As required by the WEEE (Waste Electrical and Electronic Equipment Directive) of
the European Community and the corresponding national laws, Thorlabs offers all end
users in the EC the possibility to return “end of life” units without incurring disposal
charges.
This offer is valid for Thorlabs electrical and
electronic equipment:
Sold after August 13, 2005
Marked correspondingly with the crossed out
“wheelie bin” logo (see right)
Sold to a company or institute within the EC
Currently owned by a company or institute within
the EC
Still complete, not disassembled and not
contaminated
As the WEEE directive applies to self contained operational electrical and electronic
products, this end of life take back service does not refer to other Thorlabs products,
such as:
Pure OEM products, that means assemblies to be built into a unit by the user
(e.g. OEM laser driver cards)
Components
Mechanics and optics
Left over parts of units disassembled by the user (PCB’s, housings etc.).
If you wish to return a Thorlabs unit for waste recovery, please contact Thorlabs or
your nearest dealer for further information.
7.1.
Waste Treatment is Your Own Responsibility
If you do not return an “end of life” unit to Thorlabs, you must hand it to a company
specialized in waste recovery. Do not dispose of the unit in a litter bin or at a public
waste disposal site.
7.2.
Ecological Background
It is well known that WEEE pollutes the environment by releasing toxic products
during decomposition. The aim of the European RoHS directive is to reduce the
content of toxic substances in electronic products in the future. The intent of the
WEEE directive is to enforce the recycling of WEEE. A controlled recycling of end of
live products will thereby avoid negative impacts on the environment.
Page 10
Part 8. Thorlabs Worldwide Contacts
USA, Canada, and South America
Thorlabs, Inc.
435 Route 206
Newton, NJ 07860
USA
Tel: 973-579-7227
Fax: 973-300-3600
www.thorlabs.com
email: [email protected]
Europe
Thorlabs GmbH
Hans-Böckler-Str. 6
85221 Dachau
Germany
Tel: +49-(0)8131-5956-0
Fax: +49-(0)8131-5956-99
www.thorlabs.com
email: [email protected]
UK and Ireland
Thorlabs LTD.
1 Saint Thomas Place, Ely
Cambridgeshire CB7 4EX
Great Britain
Tel: +44 (0)1353-654440
Fax: +44 (0)1353-654444
www.thorlabs.com
email: [email protected]
Japan and Asia
Thorlabs Japan Inc.
5-17-1, Ohtsuka
Bunkyo-ku, Tokyo 112-0012
Japan
Tel: +81-3-5977-8401
Fax: +81-3-5977-8402
www.thorlabs.jp
email: [email protected]
Scandinavia
Thorlabs Sweden AB
Box 141 94
400 20 Göteborg
Sweden
Tel: +46-31-733-30-00
Fax: +46-31-703-40-45
www.thorlabs.com
email: [email protected]
Page 11
Page 12
Thorlabs Ltd.
Thorlabs Inc.
1 Saint Thomas Place, Ely
Cambridgeshire CB7 4EX
Great Britain
Tel: +44 (0)1353-654440
Fax: +44 (0)1353-654444
www.thorlabs.com
435 Route 206
Newton, NJ 07860
USA
Tel: +00 1 973-579-7227
Fax: +00 1 973-300-3600
www.thorlabs.com