- Katib Technologies

Transcription

SPORTS HALL
Facility planning aid for Architects | Designers | Sports Consultants
ABOUT US
As one of the leading corporations
in the sports industry Erhard Sport
International offers a wide product
selection for more than 100 sports for
over 130 years.
As manufacturer of high quality sports
equipment Erhard Sport International
has an excellent reputation in schools,
sports clubs, town councils and retailers.
As a qualified equipment engineer and
fitter of sports hall installation Erhard
Sport International is one of the leading and most experienced suppliers.
More than 200 staff members ensure,
that your requests and inquires are
professionally handled and processed.
Site Burgbernheim
• Production • Warehouse
• Product Development/Research • Technical Department
• Information/Training Center (ESS – Erhard Sport Studio)
According to our tradition and philosophy we work constantly on new and
enhanced ideas which are reflected in
our products.
Planning a Sports Hall Installation?
Planning Assistance
As a manufacturer and supplier
of sports equipment we assist
architects and clients with wellfounded and detailed knowledge
when it comes to planning and
considering sports installation.
With over 50 years of experience in this particular field we provide
best performance to suit demanding designers and contractors.
Special Catalogue
1
2
3
4
5
6
7
8
9
10
11
Important information and advice
of sports hall installation is provided in our current special catalogue Sports Hall Equipment or at
www.sports-hall-equipment.com.
Take advantage of our knowledge
for your planning success.
12
13
14
25
2
3
4
5
6
OK Rohbeton
7
900, für Schaukelringanlage mit Schwingachsen mind. 1000 erforderlich
Wandschiene
bündig
einsetzen!
13
18
19
8
25
Geräteraum
OK Rohbeton
85
102
130
16
16
173
8
120
Bewehrung nach statischen Erfordernissen! Siehe DIN 18032/Teil 6!
9
22
Fundament-Aussparung für Pos.
40
OK Rohbeton
20
11
Nischenbreite 240
Nischenhöhe 270
168
400
8
3
25
Nischentiefe 15
2
8
Pv
D
Diese Geräteverankerung wird auf den Rohbeton aufgedübelt!
22
227
650
Maße in cm!
12
Lastannahme für Sprossenwand feststehend,
schwenkbar, hochziehbar und einschiebbar
13
Pro Befestigungspunkt ist eine Vertikallast P =2000N
und eine Horizontallast P =3000N anzunehmen.
H
230
550
Detail "A"
Bauseits abgerundete
Eckverstärkung vorsehen,
oder Seilschutz von
Fa. Erhard verwenden!
25
25
2
3
80
303
400
3
154
170
115
2
230
450
550
22
F2
60
Lt. DIN 18032/Teil 1
mind. 200 erforderlich!
2
17
In diesen Bereichen keine Fußbodenheizung!
9
33
Nischenbreite 240
Nischenhöhe 270
34
600
Volleyball-Spielfeld
3
3
33
Freiräume für Geräteverankerungen beachten!
400
Für Pos.
9
Nischentiefe 24
11
3
8
9
173
Basketball- und
Handball-Spielfeld
Nische bauseits
vorsehen!
Lichte Öffnung 30cm!
Lichte Tiefe 13cm!
Siehe Detail "A"!
13
Achtung!
17
B
Für die Befestigung der Sportgeräte
müssen bauseits statisch ausreichend
dimensionierte Boden-, Wand- und
Dachkonstruktionen vorhanden sein,
Siehe DIN 18032/Teil 6!
Wandschiene
bündig
einsetzen!
Der vorliegende Sportgeräte-Einbauplan
ist ein Planungsvorschlag!
Ein Anspruch auf Rechtsgültigkeit besteht nicht!
Achtung! Bei Elastik-Sportboden beachten!
Verstärkungsringe ab 18cm Sportbodenaufbau!
Für Pos.:
F
Lastannahme für Spielschiene
Pro Befestigungspunkt ist eine Vertikallast P =1000N
und eine Horizontallast P =1500N anzunehmen.
H
Lastannahme für künstliche Kletteranlagen
Die entsprechenden Lasten sind der EN 12572
zu entnehmen.
G
13
11
16
16
F2
Pos.
2
19
40
Fg
Zusatzhinweise:
Ausladung Basketball-Wandgerüst: siehe Vermaßung im
Sportgeräte-Einbauplan.
Ausladung Basketball-Übungsbrett: 30cm. Basketball-Deckengerüst: Ein
eventueller Schwingbeiwert ist nicht eingerechnet!
Lichte Nischenöffnung
13
9
F1
OKFF
Nischentür
158
200
Badminton-Spielfeld
227
G
We support you free of cost when planning a sports hall by providing you qualified ideas and solutions with the experience of more
than 1000 succesful completed projects. Visit us and get to know
our production facilities. Equipment to touch, quality to examine,
special solutions to discuss. All of that can be efficiently done with
us at our factory-owned "Sport Studio".
13 lichte Nischentiefe
25
200
Lt. DIN 18032/Teil 1
mind. 200 erforderlich!
E
F3
30
303
25
Mitte Sporthalle
154
158
15
154
60
F
Eigengewicht:
Fg Basketball-Deckengerüst: 3000N
Fg Basketball-Wandgerüst: 2000N
Fg Basketball-Übungsbrett: 1000N
Prüflasten
nach DIN7899/DIN-EN1270
F1=900N; F2=3200N; F3=900N
15
50
170
15
14
14a
16
18
18
Mitte Sporthalle
200
100
18
V
Lastannahme für Basketball-Anlage
60
60
50
115
154
E
J
Ph
11
Ph
13
I
C
Pro Konsole ist eine Vertikallast P =3000N
10 und eine Horizontallast P =3000N anzunehmen.V
H
Geräteverankerung für Pos.
D
H
B
Lastannahme für Klettertaue und VSK
Nach DIN1055/Teil3 sind je Klettertau, und für
die Befestigung des Trägerrohres an der Wand,
eine Vertikallast Pv=2000N und eine Horizontallast
von Ph=900N zu berücksichtigen.
Ein eventueller Schwingbeiwert ist nicht eingerechnet!
Nach DIN 18032 Teil 6 müssen die Wandbefestigungen
zur Feststellung der Taueinrichtung (nur Seilfeststeller
bei der VSK-Anlage) je Tau 2250N vertikale Last
aufnehmen können. Eigenlast je Tau: 400N.
Lastannahmen für Kletterstangen und
Gitterleiter, rollbar und hochziehbar
30
19
Nischenbreite 258
Nischenhöhe 540
Nischentiefe 24
C
Nach DIN 18032 Teil 6 müssen die Wandbefestigungen
zur Feststellung der Ringeinrichtungen (Klobenplatte,
Seilfeststeller) je Schaukelringpaar 4500N vertikale Last
aufnehmen können. Eigenlast je Ringpaar: 800N.
For your planned sports hall we
provide a customized equipment
installation plan according to
your requirements and ideas.
Fundament-Aussparung für Pos.
Nische bauseits
vorsehen!
Lichte Öffnung 30cm!
Lichte Tiefe 13cm!
Siehe Detail "A"!
17
Lastannahme für Schaukelringe, Kunstturnringe und VSK
Nach DIN1055/Teil3 sind je Schaukelringpaar, und
für die Befestigung des Trägerrohres an der Wand,
eine Vertikallast Pv=4000N und eine Horizontallast
von Ph=1800N zu berücksichtigen.
7a Ein eventueller Schwingbeiwert ist nicht eingerechnet!
33
A
A
CAD Planning
Our design and engineering
department is equipped with the
latest CAD technology. As a result,
we are able to provide you with an
optimum offer according to the
sports hall floor plan.
Equipment Installation Plan
7
B
16
Für die Montage der Sportgeräte werden bauseitige Vorkehrungen, entsprechend der DIN 18032/
Teil 6 und den Lastannahmen nach DIN 1055/
Teil 3, EN 1270 und EN 12572 vorausgesetzt.
50
1
15
2
Fundament-Aussparung für Hülsen-Steckreck, Pos.
A
Cost Listing
Upon inquiry you will receive from
us a specification of costs or a neutral specification of services.
Utilise our qualified offer! All we
need from you are your planning
documents as well as floor plans
and sectional drawings (preferably
in a measuring unit of 1:50).
Sämtliche Angaben sind eigenverantwortlich
mit den Bauplänen abzustimmen, wobei die
allgemein anerkannten sicherheitstechnischen
Regeln (z.B. DIN 18032) und bei Schulsport-
15
16
17
18
19
22
25
33
Hülsensteckreck
Spannreck, Spannstufenbarren
VSK (Vario-Schaukel-Kletter-System)
Klettertaue
Gitterleiter 4-teilig
Sprossenwand schwenkbar
Basketball Wandgerüst
Basketball Übungsbrett
Wandschiene
Spielsäule
Volleyball Netzpfosten
Badminton Netzpfosten
Handballtor mit Verankerung
Kletterwand/Boulderwand 6x3m
H
I
Alle Maße in cm!
Alle Maße, die von einer Wand
ausgehen, sind von VK fertiger Wand!
Alle Höhenangaben von OKFF!
Alle Nischenmaße sind lichte Fertigmaße!
Hinweis für den Planer:
Falls die Fundamentaussparungen größer sind, als in
J
CUSTOMIZED EQUIPMENT PLANNING
factory
The inspected
ith qualw
ds
correspon
TÜVof
ds
an
m
de
ity
e certith
r
fo
n
ge
Thürin
constant
A
ts.
fied produc
ality
qu
g
rin
tu
ac
uf
man
cere
th
d
an
d
is ensure
ons are
tification provisi
complied.
The Testing Agency for
Equipment Safety of TÜV
Thüringen designated as a
certification body for technical quipment by the Federal Minister for Labour
and Social Affairs, together with its associated testing laboratories, hereby
confirms that the products
itemised fulfil the specifications as laid down in the
current version of the Act
on Technical Equipment.
Certificate
Inspection of a
Manufacturing Facility
Certificate
Certificate
GS approved products
Inspection of
Installation & Service
Only ERHARD SPORT can provide complete and up-to-date Approval Certificates for all fixed and portable
Sports Equipment, for Inspection of Manufacturing Facility as well as for Installation and Service.
At ERHARD SPORT INTERNATIONAL, a well planned multi-sport athletic facility is our idea of Total Gym Coordination. ERHARD specializes in assisting you through every phase of a project, from product selection to product
installation and everything in between. Our engineering
department provides services unmatched by anyone in
the industry.
3
If you are planning a multi-sport athletic facility you
should realize this will be a major investment that does
not allow you to spend time, money and effort on poor
planning, poor product quality and poor service. So
please make sure you choose the right staff that can
help ease your job. It‘s easy! Call or write us – we can do
jobs others can‘t.
UNEVEN PARALLEL BARS
RING FRAME (see page 80)
HIGH BAR
240
240
FLUSH FLOOR
400
FLUSH FLOOR
550
550
www.sports-hall-equipment.com
Pull direction of
guy chain/wire
FLUSH FLOOR
Pull direction of
guy chain/wire
Detail: Floor Slab Recess
FLUSH FLOOR
30
Flush floor slab
No. 13081
Hinged Anchor Hook
to be set in concrete
20
No. 13082
Hinged Anchor Hook
to be bolted on concrete slab
Dimensions in cm
UNEVEN PARALLEL BARS • HIGH BAR • RINGS
4
performance gymnastics
high bar • rings • uneven bars
HORIZONTAL BAR ”Universal”
with universal tensioning, height
adjustment from 142 – 270 cm in
steps of 5 cm. High bar made of special
stainless spring steel, Ø 28 mm, 240 cm
long. Uprights made of heavy-gauge
steel tube with rubber covered base
plate. Including guy cables, turnbuckles and adjusting chain. Without floor
anchors.
13202
Each
HORIZONTAL BAR ”Stuttgart”
with double tensioning and safety bar.
Uprights with more elasticity. Height
adjustment from 255 – 295 cm. Safety
bar made of high quality special stainless
steel, for highest standard and safety.
The double tensioning with the licensed
key adjustment gives excellent support
and flexibility to the apparatus. Approved
by the FIG. Without floor anchors.
13203 (not shown)
Each
Ref.No. 17505
Ring Frame
HORIZONTAL BAR ”Standard”,
according to DIN specification 7903.
Height adjustment from 145 – 250 cm.
Standard tensioning. Without floor
anchors.
13204 (not shown)
Each
Ref.No. 13202
Horizontal bar with
universal tensioning
STORAGE RACK
for high bar unit.
13150 (image see page 72)
FLOOR ANCHORS for guyed gymnastic apparatus
STEEL ANCHOR HOOK
for concreting in foundation
recess.
13101
Each
HINGED STEEL ANCHOR
in socket, for concreting
in foundation recess.
13081
Each
STEEL ANCHOR HOOK
WITH PLATE
for dowelling on concrete
slab.
13102
Each
HINGED STEEL ANCHOR
for dowelling on concrete
slab.
13082
Each
ANCHOR & SOCKET COVER
for sprung floor. Flange made
of corrosion resistant alloy, 180
mm Ø clear opening. Solid PE
lid with rubber seal.
14570
Each
Each
RING FRAME
with built-in shock absorbers and additional special spring system..
17505
Each
UNEVEN BARS ”WM Dortmund”,
for competition, width between the
rails 100 - 160 cm. Round unbreakable wooden coated fiberglass rails
„Carboflex“, double tension device with
built-in ension devices and slide adjusters. Approved by FIG.
11131
Each
UNEVEN BARS
same as model ”WM Dortmund”, but
without tension conrol device.
11130 (not shown)
Each
UNEVEN BARS ”L”
functions as model ”WM Dortmund” but
width between the rails 75 – 110 cm,
without tension control device.
11120 (not shown)
Each
WALL RACK
for storage of uneven parallel bars.
Each
Ref.No. 11131
Uneven bars „WM Dortmund“
5
Deflection
Pulley
Supporting Structure
Deflection
Pulley
Hoisting Device
Belt
Rope
For the structural engineer
Design load for suspension harness:
Carbine Hook
According to DIN specification 1055 part 3 a vertical load of Pv = 4000 N and a horizontal load
of Ph = 1800 N are to be considered. A possible
swing coefficient is not included.
FLUSH FLOOR
This single rope
suspension is a
special construction
consisting of a ceiling
mounted track with a
running pulley, rope
and belt.
SUSPENSION HARNESS
6
suspension harness
SUSPENSION HARNESS
Standard model consisting of a
braided polypropylene rope with
carbine hook, single and doube deflection pulley.
17400
Set
CLAMP CONNECTOR
Standard model for steel, wood or
concrete girder.
17140
Each
CLIP ANGLE
for fixing on job site existing anchor
rail, standard model.
17150
Each
HOISTING DEVICE
for suspension harness, consisting of
pulley block with clevis type eyelet, 8
mm braided hemp rope with snaphook and wind-up bracket.
171810
Each
AGILITY BELT
made from natural tanned leather with
felt padding, hand-sewn, 2 adjustment
buckles and securely fastened D-rings
for rope attachment.
F3040010*
Each
AGILITY BELT
Hard-wearing nylon belt with reinforced
triple-sewn adjustment straps, securely
fastened D-rings for rope attachment,
including 2 looped assistant straps with
swivel carbine hook.
54905
Each
TWISTING BELT
aluminium frame with precision ball
bearings, inside heavy-duty nylon belt
and two 360° turn knuckles, Size: XS-S
(diameter 60-80 cm).
54915
Each
ADDITIONAL BELT PACKAGE
for agility belts, consisting of adjustable shoulder and chest belt as well as
an abdominal belt. Ideal for protecting
the gymnast during difficult exercises.
Without ropes.
54906 Set
*) Ref.No. F3040010 determines Ref.No. 54910 without hand held assistant hemp ropes.
Ref.No.
54905
Ref.No.
54915
7
Dimensions in cm
Supporting girder pipe
Rope guide element
200
min. 175
Rope
Snap hook to attach
various elements
(i.e. swing rings,
rope ladder, etc.)
For the structural
engineer
Rope adjusting
and locking
device
Design load for VSC System:
Load: According to DIN specification 1055 part 3 for each pair of
ropes a vertical load of Pv = 4000 N
and a horizontal load of Ph = 1800
N are to be considered (a possible
swing coefficient is not included).
Dead load: G = 800 N for each
pair of ropes.
FLUSH FLOOR
Clamping
lever
Mounting plate
Triangular
securing plate
Rope adjusting
and locking
device
locked
unlocked
ACCESSORIES FOR VSC SYSTEM
min. 280
rope ladder
Solid wooden rungs with 10 mm PP rope and suspension ring. Maximum load capacity 100 kg.
16660 Per meter
13
ROPE LADDER
Solid wooden rungs with 10 mm PP rope and
suspension ring. Maximum load capacity 100 kg.
Fixed length 200 cm.
81232
Each
clear recess
measures
Front
finished
wall
Section
B
200
Flush front
finished wall
A
1-4 pairs VSK
A = 40 cm
B = 13 cm
FLUSH FLOOR
HAMMOCK
made from heavy-duty woven cotton cloth.
81190 300 x 140 cm (usable area)
Each
81191 350 x 160 cm (usable ares)
SWING CLOTH 3 x 3 m
KNOT ROPE
Tear-proof PE cloth with surrounding sewn cord
PP rope Ø 24 mm with suspension ring. Rope knots and 4 suspension loops.
every 50 cm. Maximum load capacity 200 kg.
81224
Each
81219
Per meter
CLIMBING NET 2 x 2 m
KNOT ROPE
made from 16 mm PP rope, with attachment bar.
PP rope Ø 24 mm with suspension ring. Rope knots 81222
Each
every 50 cm. Maximum load capacity 200 kg.
CLIMBING
NET
"Herkules",
2
x
2
m
Fixed length 200 cm.
81220
Each made from 16 mm PP rope with steel wire insert,
with attachment bar.
RUBBER SWING DISC Ø 30 cm,
81223
Each
with PVC covered chain 200 cm long, with susCLIMBING
NET
3
x
2.5
m
pension ring.
17321
Each made from 16 mm PP rope, with attachment bar.
81238
Each
RUBBER SWING SEAT 45 x 20 cm,
CLIMBING
NET
"Herkules",
3
x
2.5
m
with steel core and extremely elastic edges, with
made from 16 mm PP rope with steel wire insert,
12 cm chain and suspension ring.
81208
Each with attachment bar.
81239
Each
PLYWOOD SWING SEAT 80 x 80 cm,
CLIMBING
ROPE
with 4 suspension rings and 4 screw chain links to
for hanging height 550 cm.
attach to existing ropes.
Each
80209
Each 16620
81207 SWING DISC
Each
VSC – VARIABLE SWING & CLIMBING SYSTEM
8
Each
THERAPY INSERT PAD
60 x 60 x 6 cm, firm foam padding with hardwearing synthetic leather cover.
81194
Each
vsc variable swing climbing system
VSC – VARIABLE SWING AND
CLIMBING SYSTEM
suitable for 1-2 pairs of VSC ropes.
Consisting of 2 deflection pulleys for
1-2 pairs of ropes, rope lock and VSC
ropes with sewn loop at one end,
safety snap-hook.
17350
Each
VSC – VARIABLE SWING AND
CLIMBING SYSTEM
suitable for 3-4 pairs fo VSC ropes.
Consisting of 2 deflection pulleys for
3-4 pairs fo ropes, rope lock and VSC
ropes with sewn loop at one end,
safety snap-hook.
17352 Each
ROPE BRACKET
to wind up excess length of 1 pair of
VSC ropes.
17320
Each
RUBBER WEIGHTS with lead core.
17182
Pair
WEIGHT BAG with loop strap.
17184
Each
CORNER DEFLECTION PULLEY
for 1 pair of VSC ropes.
17354
Each
for 2 pairs of VSC ropes.
17355
Each
17356
Each
17357
Each
WALL FIXING
for each rope locking device in case
of wall facing.
17358
Each
ROPE DEFLECTOR
for 1-2 pairs of VSC ropes with installation of VSC rope locking device in
recess.
17359
Each
ROPE DEFLECTOR
for 3-4 pairs of VSC ropes with installation of VSC rope locking device in
recess.
17360
Each
STAINLESS STEEL U-BOLT
suitable for supporting steel pipe section 100 x 80 mm.
Requisite: for each VSC unit 4 pieces,
for deflection pulley 2 pieces.
F1000020
Each
STAINLESS STEEL U-BOLT
suitable for supporting steel pipe section 120 x 80 mm.
Requisite: for each VSC unit 4 pieces,
for deflection pulley 2 pieces.
F1000025
Each
SAFETY SNAP-HOOK (spare part)
70752
Each
SWING RINGS
consisting of 2 plywood rings with
prestretched 40 mm polyester strap
and triangular ring, 100 cm long.
17362
Pair
9
Supporting
girder pipe
Track
Length according
to number of ropes
(max. 8 ropes)
min150
100
100
100
Climbing rope
Ø 3.2 mm
Wall cabinet or recess
for flush wall storage
of climbing ropes
FLUSH FLOOR
Dimensions in cm
Clear recess measures
(from backside of door)
Section
min. 280
B
Design load for Climbing Ropes:
Load: According to DIN specification 1055
part 3 for each climbing rope a vertical load
of Pv = 2000 N and a horizontal load
of Ph = 900 N are to be considered
(a possible swing coefficient is not included).
Dead load: G = 400 N per rope.
Flush front
finished
wall
A
1-8 Ropes A =40 cm
B =13 cm
Engaging pawl
with pull rope for
disengaging
FLUSH FLOOR
Tauhalter mit Feststellkette
in verkleideter Nische.
CLIMBING ROPES DIN 7911-2
10
climbing ropes
DIN 7911-2
CLIMBING ROPE TRACK
made from specially formed steel section and smooth running ball-bearing
travellers, catch lock with ooperating
line and spacer chains.
16500 for 3 climbing ropes
Each
Each
Each
Each
Each
STANDARD BEAM CLAMP
for attaching track to the cieling
structure (steel-, timber- or concrete
beam).
16550
Each
STANDARD ANGLE IRON
for attaching track to existing supporting structure on site.
16560
Each
CLIMBING ROPE
made from 32 mm diameter 4 strand
top grade manilla with galvanized
rope clamp, rope end covered with
plastic sheath.
for 550 cm hanging height
16620 Each
16630 Each
16600 Each
16610
Each
ADHESIVE WARNING LABEL
"DO NOT KNOT ROPE !"
16605
Each
rope lock
with chain clamp.
16570
Each
ROPE HOISTING KIT
to accomodate retracted and bundled
up climbing ropes, consisting of pulley
block with clevis type eyelet, 8 mm
braided hemp rope with carbine swivel
and wind-up bracket.
171813
Each
Adhesive Warning Label
"DO NOT KNOT ROPE !"
11
Fixed Wall Bars | Single Bay Unit – 100 x 260 cm
wall bracket
107
side wall
rung
wall bracket
260
side wall
rung
200
200
260
wall bracket
Fixed Wall Bars | Double Bay Unit – 100 x 260 cm
207
FLUSH FLOOR
20
20
wall bracket
100
200
130 clear recess width
270 clear recess height
(finished)
230 clear recess width
270 clear recess height
(finished)
(If the width of the recess is 24 cm, the wall will flush with the front of the finished wall according to DIN spec. 7910)
Hinged Wall Bars | Double Bay Unit – 100 x 260 cm
208
13
227 until finished wall in recess
260 height of wall bars
Flush floor slab
33
225 until centre of pivot iron
270 clear recess height (finished)
225 centre rest iron (finished size)
240 clear recess width (finished)
FLUSH
FLOOR
25
Dimensions in cm
WALL BARS | FIXED DIN 7910 | HINGED
12
WALL BARS
FIXED | HINGED
DIN 7910 / EN 12346 (safety requirements and test procedures)
wall pivot
locking device
with snapping pin
Design load for
fixed and hinged wall bars.
According to DIN 18032
per wall bracket must be
considered a
vertical load:
PV = 2000 N
horizontal load: PH = 3000 N
floor pivot
No. 15201
Hinged wall bars with
close spaced rungs.
Lifter
15290
shoot bolt
with floor plate
FIXED Wall BarS
DIN 7910 specification. Timber side walls
with oval shaped laminated beech wood
rungs individually screwed, including
mounting hardware.
15000 Single bay 100 x 260 cm Each
15010 Single bay 100 x 280 cm Each
15020 Double bay 200 x 260 cm Each
15030 Double bay 200 x 280 cm Each
No. 15200
Hinged wall bars with
wide spaced rungs.
hinged Wall Bars
with close spaced rungs, DIN 7910.
Double bay unit 200 x 260 cm. Timber
side walls with oval shaped laminated
beech wood rungs individually screwed,
easy moving on non-marking rolls. Tubular
powder coated steel fixing post with 2
guiding brackets and tapered cuff to
locate 90° hinged wall-bars in socketed
position. Including wall locking device
and mounting hardware.
15201
Each
lifter for socketed parallel bars
and wall bars fixing post.
15290
Each
hinged Wall BarS
with wide spaced rungs. Double bay
unit 200 x 260 cm. Timber side walls
with oval shaped laminated beech
wood rungs individually screwed, easy
moving on non-marking rolls. Tubular
powder coated steel fixing post with 2
guiding brackets and tapered cuff to
locate 90° hinged wall-bars in socketed position. Including wall locking
device and mounting hardware.
15200
Each
Ground Socket
stainless steel with chuck cone and
cylinder guide.
15251
Each
Socket cover – medium
for sprung or multi-elastic floor, clear
opening 130 mm, aluminium flange
with plastic lid.
15270
Each
13
235
Electric motor
Electric motor
572.5
558.5
Design load for vertically
retractable wall bars:
PH
per wall/ceiling bracket
Vertical load:
PV = 2000 N
Horizontal load: PH = 3000 N
must be considered.
Wall bracket
Supply Lines for E-Motor
Cable Winch No. EM209
230 volt • Output 0.31 kW
from mains to contact switch.... 3 x 1.5 mm2
Belt band
from contact switch to motor
system „Totmann“................... 4 x 1.5 mm2
PV
PH
270.5
256.5
WALL BARS
HINGED 90°
FLUSH
FLOOR
Flush floor slab
33
228 from finished wall
Footing
40 x 25 cm
25x40
Dimensions in cm
WALL BARS | HINGED AND VERTICALLY RETRACTABLE
14
RETRACTABLE WALL BARS
VERTICALLY – hinged | fixed
Ref.No. 59520
Safety lock
retractable
hinged wall bars
Double bay unit 200 x 260 cm,
hinged and retractable up to 2.5 m
height. Timber side walls with oval
shaped laminated beech wood rungs
individually screwed, easy moving on
non-marking rolls. Tubular powder
coated steel fixing post with 2 guiding
brackets and tapered cuff to locate
90° hinged wall-bars in socketed position. Metal guiding frame and rails are
powder coated.
Lifting device by means of electric
motor winch with built-in limit switch.
Connected load 230 volt, 0.31 kW.
15205
Each
GROUND SOCKET
made from stainless steel, with conus
and cylinder guidance.
15251
Each
SOCKET COVER – MEDIUM
for sprung floor or multi-elastic floor,
clearance hole 130 mm, aluminium
flange with plastic lid.
15270
Each
Wall bars hinged 90°
and fixed with
socketed post
retractable
fixed wall bars
Double bay unit 200 x 260 cm, retractable up to 2,5 m height. Timber side
walls with oval shaped laminated beech
wood rungs individually screwed. Metal
guiding frame and rails are powder
coated.
Lifting device by means of electric
motor winch with built-in limit switch.
Connected load 230 volt, 0.31 kW
15037
Each
SAFETY LOCK
Automatically operating safety device
in case of totally broken pull cables or
pull straps.
59520 Each
MOUNTING BRACKET
for safety lock.
VM258 Each
Wall bars 250 cm above floor,
lifted in rest position
15
Height clearance passageway 271
Front finished wall
360
FLUSH
FLOOR
Front finished wall
Width clearance
passageway 30
217
Design load for retractable wall bars:
per attachment point
33
Flush floor slab
Vertical load:
PV = 2000 N
Horizontal load: PH = 3000 N
must be considered.
25
Dimensions in cm
WALL BARS | HORIZONTALLY RETRACTABLE
16
RETRACTABLE WALL BARS
horizontally
RETRACTABLE WALL BARS.
Double bay unit 200 x 260 cm, retractable (e.g. into equipment storage
room). Timber side walls with oval
shaped laminated beech wood rungs
individually screwed, easy moving on
non-marking rolls. Tubular powder
coated steel fixing post with 2 guiding
brackets and tapered cuff to locate 90°
hinged wall-bars in socketed position.
Slide rail including runners.
15220
Each
ground socket
made from stainless steel, with cone
sleeve and cylindric guide.
15251
Each
For more information
on fixed wall-bars see
page 34.
socket cover – medium
for sprung floor or multi-elastic floor,
clearance hole 130 mm, aluminium
flange with plastic lid.
15270
Each
Fixed double bay wall bars 200 x 260 cm
17
BACKWARD FOLD BASKETBALL BACKSTOP
for attachment height up to 8.0 m
lower ceiling surface
electric cable winch
about
110
supporting girder pipe
120
305 above
finished floor
290 above finished floor
backboard 105 x 180 cm with
4 mounting holes according to DIN spec.
GENERAL CONSTRUCTIONAL FEATURES
Backstop supporting structures with rigid vertical steel frame and a hinged rear
oblique frame. Fabricated out of welded 3 mm gauge steel pipe with horizontal
spreaders for stability, vertical and oblique frames with pivot bearings. Dual cable
operation for added protection against possibility of a folding backstop accidentially
falling during the raising or lowering cycle or while in storage.
Location of cable
winding with electic motor.
Shown supporting
girder pipes for
attachment of backboard supporting
structure have been
installed on site and
are stronger dimensioned than standard
girder pipes section
100 x 80 mm (see
image on page 48).
Design load for ceiling suspended
backstop support structure:
Working load according to DIN 7899
F1 = 900 N
F2 = 3200 N
F3 = 900 N
Dead load: 4000 N
Dimensions in cm
OVERHEAD SUPPORTED BASKETBALL BACKSTOPS
18
basketball backstops
overhead supported | backward folding type
Basketball backstop
support structure
BACKWARD FOLD. Hinged vertical
strut frame and folding bracing frame,
powder coated*, without backboard.
59480
Each
backboard ATTACHMENT frame
made out of steel profiles with heavy
steel goal mounting plate, according
to EN 1270 standard for suspended
structures and FIBA requirements.
59377
Each
ELECTRIC CABLE WINCH
Touch contact controlled electric operation with integral limit switch. Steel drum
with cable guide discs. Connected load:
230 volt, 0.43 kW.
EM213
Each
BACKBOARD HEIGHT ADJUSTER
Self-locking spindle device progressively adjustable from 260 to 305 cm
rim height, manual operation by awning
crank type handle.
59370
Each
free fall safety device
for the unlikely event of a cable or
winch failure.
59516
Each
cross brace
with mounting bracket for free fall
safety device.
VM251
Each
CROSS MEMBERS
for attachment of supporting girder
pipes to be provided according to
statical and on-site requirements.
for the attachment of the backstop
supporting structure to be provided
according to statical and on-site
requirements.
Ref.No. 59516
Free Fall Safety Device
Steelwork requirements
to fix the necessary supporting structure have to
be either provided job-site
according to DIN spec. 18032/6
or to be extra specified in
the tender according to the
situation at site.
For backboards, rims and nets
see page 54-55
19
BACKWARD FOLD BASKETBALL BACKSTOP
Backboard attachment with F.I.B.A. Certificate of Compliance (attachment height up to max. 7.80 m)
appr. 110
175
305 above
finished floor
BACKWARD FOLD BASKETBALL BACKSTOP – REINFORCED MODEL
for attachment height above 8.10 m up to max. 9.60 m
aoor. 110
175
F1 = 900 N
F2 = 3200 N
F3 = 900 N
Dead load: 3000 N
Dimensions in cm
305 above
finished floor
Backstop supporting structures on this page feature a rigid vertical steel
frame and a hinged rear oblique frame. Fabricated out of welded 3 mm
gauge steel pipe with horizontal spreaders for stability, vertical and oblique
frames with pivot bearings. Dual cable operation for added protection
against possibility of a folding backstop accidentially falling during the
raising or lowering cycle or while in storage.
F1
F2
20
overhead supported | backward folding type
DIN 7899 / EN 1270 (safety requirements and rest procedures)
CROSS MEMBERS
pipes to be provided according to satatical and on-site requirements.
rquirements.
Steelwork
requirements
to fix the necessary
supporting structure
have to be either provided job-site according to DIN spec. 18032/6 or
to be extra specified in
the tender according to
the situation at site.
IMPORTANT NOTE
Attachment height and location will
determine proper style of structure.
In order to be able to customize supporting girder pipes for the attachment of backstop supporting structures the contractor is liable
to provide all necessary cross
members for the attachment of the
supporting girder pipes.
Thus it is mandatory to provide us
ground plan and section of the building so we can prepare the essential
installation plan for the contractor.
Basketball backboard
support structure
BACKWARD FOLD
F.I.B.A. SPECIFICATION
Extra wide reinforced hinged vertical
for attachment height up to max.
7.80 m. All metal parts are powder
coated*, without backboard.
59509
Each
Portable Basketball Backstops
see current handbook
for sports eqipment.
Fig.:
BACKWARD FOLD backstop # 59510,
reinforced model including safety glass
backboard # 59387 with padding, snap back
goal ring and net.
Fig.:
BACKWARD FOLD backstop # 59509,
reinforced model including safety glass
backboard # 59387 with padding, snap back
goal ring and net.
BACKBOARD ATTACHMENT FRAME
made out of welded steel profiles with
heavy steel goal mounting plate, for
backboard support structure according
to FIBA specification.
59193
Each
Basketball glass backboard
180 x 105 cm, 12 mm fully tempered
safety glass with sparing for steel goal
mounting plate. Attachment according
to FIBA requirements.
59387
Each
backboard padding
according to FIBA requirements. Durable molded PE foam with tough vinyl
coated PVC cover. A steel insert provides
strength at all of the mounting locations
and stiffness along the bottom of the
backboard.
59189 Each
Basketball goal "Flexmatic"
according to FIBA requirements.
Goal is provided with a positive
lock release mechanism which is
adjustable to conform to FIBA recommendations. Tube-tie net attachment
system improves safety by eliminating
conventional formed wire ties. Basic
release adjustment at 93 kg (according
to FIBA recommendations between 82
and 105 kg), without net.
59455
Each
Touch contact controlled electric
operation with integral limit switch.
Steel drum with cable guide discs.
Connected load: 230 volt / 0.43 kW
(connection and switch job site)
EM219
Each
FREE FALL SAFETY DEVICE
winch failure.
59516 Each
59517 for 12 m cable length
Each
cross brace
safety device.
VM259
Each
*) The colour of all steel parts may be specified by the
architect or customer. If not otherwise agreed on we will finish
the steel parts in neutral grey colour similar to RAL7036.
see page 54-55.
21
Y-SHAPED FORWARD FOLD BASKETBALL BACKSTOP
120
305 above
finished floor
FORWARD FOLD BASKETBALL BACKSTOP – REINFORCED MODEL
for attachment height above 8.10 m up to max. 9.60 m
appr. 40 cm
175
F1 = 900 N
F2 = 3200 N
F3 = 900 N
Dead load: 4000 N
305 above
finished floor
F2
Dimensions in cm
F1
F3
F2
CEILING SUSPENDED BASKETBALL BACKSTOPS
22
ceiling suspended | forward folding type
Backward folding
reinforced backstop
support structure,
according to FIBA criteria.
see page 54-55
FOR BEST PLANNING RESULTS
OF CUSTOMIZED CEILING
SUSPENDED BASKETBALL BACKSTOPS PLEASE PROVIDE FLOOR
PLAN, VERTICAL SECTION AND
GIRDER DETAILS OF THE
RELEVANT PROJECT.
Forward folding
reinforced backstop
support structure,
adjustable height.
BACKstop SUPPORT STRUCTURE
forward fold. Reinforced hinged vertical
strut frame and folding bracing frame for
attachment height above 7.80 m, with
lateral sway bracing for rigidity. Fabricated
out of steel pipe with horizontal and diagonal spreaders for exceptional stability,
vertical frame pivot with ball bearings,
powder coated, without backboard.
59512
Each
backstop support structure
backward fold. Reinforced hinged vertical
strut frame and folding bracing frame for
attachment height above 7.80 m, with
lateral sway bracing for rigidity. Fabricated
out of steel pipe with horizontal and diagonal spreaders and additional laterl bracing
for exceptional stability, vertical frame
pivot with ball bearings, powder coated,
without backboard.
59510
Each
backstop support structure
Y-shaped foward fold. Oblique strut
frame and hinged front oblique bracing frame for attachment height up
to 7.80 m, powder coated, without
backboard.
59481
Each
backboard attachment frame
steel goal mounting plate, according to FIBA requirements for ceiling
suspended structures.
59377 Each
backboard height adjuster
Self-locking spindle device progressively adjustable from 260 to 305
cm rim height, manual operation by
awning crank type handle.
59370
Each
Touch contact controlled electric
operation with integral limit switch.
Steel drum with cable guide discs.
Connected load: 230 volt, 0.43 kW,
Supply lines, connection and switch to
be provided job-site by customer.
EM219
Each
Automatically working safety device
winch failure.
59516
Each
59517 for 12 m long cables
Each
cross brace
for free fall safety device. Applicable for
girder pipe distance 175 cm only!
VM259
Each
CROSS MEMBERS
requirements.
situation at site.
23
FORWARD FOLD BASKETBALL BACKSTOP
about 40 cm
120
backboard 105 x 180 cm
with 4 mounting holes
according to DIN spec.
305 above
finished floor
F3
F2
F2
Backstop supporting structure with rigid vertical steel frame and a hinged rear
oblique frame. Fabricated out of welded 3 mm gauge steel pipe with horizontal
spreaders for stability, vertical and oblique frames with pivot bearings. Dual cable
operation for added protection against possibility of a folding backstop accidentially
falling during the raising or lowering cycle or while in storage.
F1
Dimensions in cm
Location of cable
winding with
electric motor.
Shown supporting
girder pipes for attachment of backboard
supporting structure
are made from standard pipe section 100 x
80 mm.
F1 = 900 N
F2 = 3200 N
F3 = 900 N
Dead load: 4000 N
24
overhead supported | FORward folding type
Basketball backstop
support structure
FORWARD FOLD. Hinged vertival
powder coated*, without backboard.
59482 Each
to EN 1270 standard for suspended
structures.
59377 Each
Touch contact controlled electric operation with integral limit switch. Steel
drum with cable guide discs. Connected
load: 230 volt, 0.43 kW (supply lines,
connection and switch to be provided
job-site).
EM213
Each
crank type handle.
59370
Each
winch failure.
59516 Each
cross brace
safety device.
VM251 Each
CROSS MEMBERS
Ref.No. 59516
requirements.
situation at site.
OF CUSTOMIZED CEILING
SUSPENDED BASKETBALL BACKSTOPS PLEASE PROVIDE FLOOR
PLAN, VERTICAL SECTION AND
GIRDER DETAILS OF THE
RELEVANT PROJECT.
see page 54-55
25
UPWARD FOLD WALL MOUNTED BASKETBALL BACKSTOP
120
free fall
safety
device
guy cable
pull cable
pull cable
backboard support structure
305 above
finished floor
F3
F1
backboard projection according to playfield lines
F2
F2
Design load for wall mounted backstop support structure:
F1 = 900 N
F2 = 3200 N
F3 = 900 N
Dead load: 3000 N
Dimensions in cm
WALL MOUNTED BASKETBALL BACKSTOPS, UPWARD FOLD
26
wall mounted basketball backstops
electrically operated upward folding typa
Ref.No. 59516
WALL MOUNTED
Basketball backstop
support structure
UPWARD FOLD. Hinged horizontal
powder coated, without backboard.
59625 Each
steel goal mounting plate.
59626 Each
Touch contact controlled electric operation with integral limit switch. Steel
drum with cable guide discs. Connected
load: 230 volt, 0.43 kW (supply lines,
connection and switch to be provided
job-site).
EM213
Each
crank type handle.
59627
Each
winch failure.
59516 Each
cross brace
safety device.
VM251 Each
see page 54-55
27
projection according to field marking
180
105
24
maximum 200 cm
60
305 above
finished floor
F3
F1
305
F2
291
290
F2
locking/disengaging
bracing bar with
operating handle.
FLUSH
FLOOR
FLUSH
FLOOR
60
60
folding direction
left or right
F1
playfield axis
F3
Design load for side swing folding
type backstop support structure:
F1 = 900 N
F2 = 3200 N
F3 = 900 N
Dead load: 2000 N
Dimensions in cm
WALL HINGED FOLDING TYPE BASKETBALL SYSTEM
28
wall mounted | fixed | side swing folding type | height adjustable
B)
side swing wall mounted unit
(with MDF backboard)
wall mounted
A) FIXED
Braced steel frame construction, powder coated*, without backboard.
59341 Projection 120 cm Each
Each
59351 Projection 165/170 cm B) SIDE SWING
Braced steel frame construction,
powder coated*, including portable
handle with hook to disengage lock
mechanism of frame bracing pipe,
without backboard.
59340 Projection 120 cm
Each
59341 Projection 165/170 cm Each
C) SIDE SWING WITH HEIGHT ADJUSTER
Braced steel frame construction,
powder coated*. Self-locking spindle device continuously adjustable
from 260 to 305 cm rim height,manual
operation by awning crank type handle,
without backboard.
59342 Projection 120 cm
Each
59343 Ausladung 165/170 cm Each
B)
side swing
wall mounted unit
(with acrylic backboard)
BACKBOARD ATTACHMENT FRAME
made of steel profiles with haeavy
steel goal mounting plate.
Each
Self-locking spindle device progressively adustable from 260 to 305 cm
crank type handle.
59370
Each
BACKBOARD PADDING
made of durable molded PE foam
(for more models see page 48).
59190 for 12 mm backboard Each
59191 for 30 mm backboard
Each
Each
59195 for 21 mm backboard
OF CUSTOMIZED WALL
MOUNTED BASKETBALL
BACKSTOPS PLEASE PROVIDE
FLOOR PLAN AND VERTICAL
SECTION OF THE RELEVANT
PROJECT.
see page 55-55
C)
side swing wall mounted unit
with height adjuster
(with glass backboard)
29
basketball backboards | backboard padding
made of MDF (Medium Dense Fibre) | made of Acrylic Glass | made of single pane Safety Glass
180 x 105 cm
BACKBOARD
ATTACHMENT FRAME
made of steel profiles with heavy
to FIBA requirements. Can also be
used as a conversion unit for existing
basketball structures with attachments according to former DIN spec
7899 (min. height above finished floor
290 cm) for backboards size 180 x
105 cm, without goal and net.
59376 Each
Molded fixing plate is
welded to the steel frame
to ensure stiff goal ring
attachment.
Ref.No. 59392
The novel
method of fixing
the acrylic board
to the steel frame
without screws
avoids breakage
of the acrylic
board caused
by material
extension due to
variation in
temperature.
Ref.No. 59402
MDF* BACKBOARDS
30 mm, both sides with white
melamin resin coating and black line
marks on front.
59399 180 x 120 cm
Each
59400 180 x 105 cm
Each
120 x 90 cm
22 mm, both sides with white
melamin resin coating and black line
marks on front.
59401 180 x 120 cm**
Each
59402 180 x 105 cm
Each
59423 120 x 90 cm
Each
59428 90 x 60 cm
Each
*) MDF = Medium Dense Fibre
**) Only in combination with counterplate No. 59605
Ref.No. 59423
ACRYLIC GLASS
BACKBOARD 10 mm thick, on
welded steel frame with fixing
bolts for attaching to supporting
structure with fixing points according to DIN specification.
59391 180 x 120 cm Each
59392 180 x 105 cm Each
No impact on the backboard caused by direct
application of force due to cut-out for separate
steel mounting plate on backboard frame.
12 mm
21 mm
30 mm
37 mm
70 mm
backboard padding
made in one piece of durable molded PE foam.
(Ref.No. 59189 with additional metal insert for mounting
to extra wide backboard frame)
59190 for 12 mm thick boards
Each
Each
Each
59196 for 37 mm thick boards (Fiber Glass) Each
59197 for 45 mm thick boards (US model)
Each
59189 for 70 mm thick boards (FIBA)
Each
SAFETY GLASS BACKBOARD*
180 x 105 cm, 12 mm thick, single pane tempered safety glass
with splinterproof foil and stud bolts on the DIN attachment
points, including mounting hardware set.
1. Mounting holes according to EN 1270 / DIN 7899.
59386
Each
Ref.No. 59386 (without goal ring and padding)
30
2. Mounting holes according to FIBA specification
(in the corners).
59387
Each
*) recommended as standard backboard for main playfield
practice backboards | goal rings
PRACTICE BACKBOARD ADJUSTABLE HEIGHT
basketball practice goal
- height adjustable Made of 21 mm thick wooden MDF
board with black target mark. Metal
wall bracket, powder coated, projection about 25 cm. Height continuously
adjustable by threaded spindle from
260 to 305 cm rim height, easy floor
level operation by awning crank type
handle, including ring and net.
90
120
F3
With Ring "Standard" (59441)
59555 Backboard 120 x 90 cm Each
59556 Backboard 90 x 60 cm Each
66
F1
260 - 305 ABOVE FINISHED FLOOR
F2
14
Design load for wall mounted
practice backboards: Working
load according to DIN 7899
F1 = 900 N
F2 = 3200 N
F3 = 900 N
Dead load: 1000 N
252
Ref.No. 59558
Practice backboard 90 x
60 cm with ring "School"
With Ring "School" (59440)
59557 Backboard 120 x 90 cm
59558 Backboard 90 x 60 cm
Each
Each
FLUSH FLOOR
14
30
FLEXMATIC
„US PRO“
Basketball Goal "STANDARD"
Official ring diameter, with net hooks,
powder coated.
59441 without net
Each
56
45
90 (60)
(120 x 90)
120 (90)
(90 x 60)
PRACTICE BACKBOARD FIXED HEIGHT
F3
F2
297
F2
305 above flush floor
F1
Dimensions in cm
FLUSH FLOOR
14
22
basketball PRACTICE GOAL
- FIXED HEIGHT Made of 21 mm thick wooden MDF
board with black target mark. Metal
wall bracket projection 25 cm, including goal ring and net.
59550 board 120 x 90 cm
Each
59551 board 90 x 60 cm
Each
Basketball goal "school"
Reinforced ring according to EN 1270 /
DIN 7899 (240 kg), tube-tie net attachment for added player safety, complete
with mounting hardware.
59440 without net
Each
Basketball competition goal
"FLEXMATIC OFFICIAL", conforms to
FIBA regulations, encased twin-shock
absorbing rebound system, tube-tie net
attachment for added player safety.
59442 without net Each
Basketball goal
"FLEXMATIC SCHOOL"
reinforced goal with open single-shock
absorbing system, tube-tie net attachment for added player safety.
59444 without net
Each
Basketball competition goal
"FLEXMATIC US PRO"
conforms to FIBA regulations, encased
spring type rebound mechanism as per
US standards, tube-tie net attachment
for added player safety.
59456 without net Each
STANDARD
„SCHOOL“
EN 1270
DIN 7899
FLEXMATIC
„OFFICIAL“
FLEXMATIC
„SCHOOL“
31
Net Antenna
approx. 260
243 (Gents)
224 (Ladies)
VOLLEYBALL
NET POSTS 91 x 91 mm
Net Height
243 (Gents)
Net Height
224 (Ladies)
VOLLEYBALL
NET POSTS 80 x 80 mm
FLUSH FLOOR
1100
WALL RAIL
FOR NET AND TETHER TENSIONING
8
Wall Rail mounted
flush with wall facing
215
25
GAME POST Ø 80 x 80 mm
265
Front Finished Wall
Wall Rail for Net- and Tether Games
33
Flush floor slab
38
65
18
Wall Rail
Ref.No. 18010
FLUSH FLOOR
Wall Front
17
3
Dimensions in cm
VOLLEYBALL POSTS • GAME POSTS
32
FLUSH FLOOR
ball games equipment | volleyball
EN 1271
Aluminium Section
80 x 80 mm
Our state-of-the-art Volleyball
Systems are easy to operate,
designed to last, and safely
serve their purpose for many
years.
56812
Das Komplettprogramm
für Volleyball-Netzpfosten
und Zubehör finden Sie in
Please
askaktuellen
for moreHauptunserem
detailed information
katalog.
18034
15300
on International
Competition Volleyball Posts.
18060
18000
standard wall rail
Section HM 38/17, galvanized, fitted
with 2 adjustable flap rings to attach
net or tether.
18000 Each
SOCKET COVER – LARGE
for sprung or multi-elasic floor, clear
with plastic lid.
14570
Each
SAFETY WALL RAIL
Section HM 38/17, galvanized, fitted
with 2 adjustable flap rings to attach
net or tether.
18010 Each
NET TENSION STRAP
for game posts, 25 mm wide web belt
with self-locking buckle.
56764
Each
game post
anodized aluminium post, section 80
x 80 mm with 2 opposite slots and
adjustable hooks for net or tether on
one side.
18032
Each
CENTER GAME POST
anodized aluminium post, section 80
x 80 mm with 2 opposite slots and
adjustable hooks for net or tether on
both sides .
18034
Each
ground socket
aluminium with anti-corrosion coating.
UBS basic socket #2 suitable for post
sections Ø 83 mm and 80 x 80 mm.
15302
Each
MULTI GAME POSTS
anodized aluminium post, section 80 x
80 mm, inside tensioning device, net/
cord height continuously adjustable.
Height scale with special game selection, without ground sockets.
18060
Pair
TELESCOPIC COMPETITION
VOLLEYBALL NET POSTS
according to FIVB regulations for
international tournaments. Height
adjustment at full net tension from
200-250 cm. The 90 mm Ø telescoping post slides inside a 120/100 mm
upright, both constructed from special
anodized aluminium section.
56812 Worm Gear Tensioning Device
Pair
56813 Pulley Tensioning Device
Pair
VOLLEYBALL POSTS 80 x 80 mm
according to EN 1271, constructed
from special anodized aluminium section, weight of tensioning post approx.
15 kg. Non-protruding inside worm
gear tensioning device with slider type
net height adjustment, continuously
variable with fine adjustment. Stateof-the-art construction providing top
safety standards.
56885
Pair
Volleyball posts 91 x 91mm
according to EN 1271, constructed
from special anodized aluminium section, weight of fensioning post approx.
15.5 kg. Non-protruding inside worm
gear tensioning device with slider type
net height adjustment, continuously
variable with fine adjustment. Stateof-the-art construction providing top
safety standards..
56867 Pair
GROUND SOCKET
15302
Each
GROUND SOCKET
aluminium with anti-corrosion coating. UBS basic socket #1 suitable for
post sections 91 x 91 mm and 120
x 100 mm.
15300
Each
opening Ø 180 mm, aluminium flange
with plastic lid.
14570
Each
GROUND SOCKET INSERT
Aluminium adapter sleeve for post section Ø 83 mm and 80 x 80 mm.
15301
Each
ground socket
UBS basic socket #1 suitable for
post sections 91 x 91 mm and 120
x 100 mm.
15300
Each
FOR OUR VOLLEYBALL POSTS
WE USE SPECIAL COMPUTER
DESIGNED ALUMINIUM SECTIONS
TO PROVIDE UNSURPASSED
STIFFNESS UNDER MAXIMUM
NET TENSION.
33
107
TENNIS
FLUSH FLOOR
Centre strap fixing
hook to dowel on
floor slab
640
640
Net Axis
Tennis Posts
33
Flush floor slab
FIELD AXIS
TENNIS POST SECTIONS
25
BADMINTON
TOP EDGE NET
155
33
Flush floor slab
20
FIELD AXIS
FLUSH FLOOR
NET AXIS
Dimensions in cm
606
TENNIS • BADMINTON
34
tennis | badminton
EN 1510
EN 1509
approved
58060
Tennis Posts
56783
56764
15302
15302
Ground Socket
TENNIS POSTS 80 x 80 mm
constructed from special anodized
aluminium section with internal worm
gear net stretching device..
58060 (without ground sockets)
Pair
56783
Aluminium
section
83 mm Ø
GROUND SOCKET
15302
Each
PORTABLE BADMINTON FLOORING, IBF approved
Extremely hard-wearing portable badminton sports flooring for practice and competition.
Standard colour: blue with yellow marking lines. Dimensions: 15 x 6.66 m, thickness 3.7
mm. • 2 rolls of 15 x 3.33 m, weight per roll about 180 kg, easy to transport. The two
court sections join together by special adhesive tape. • Supply includes ready-to-use
flooring sections rolled on drum, and adhesive tape for joining the two sections.
57870
Complete Set
SOCKET COVER - LARGE
with plastic lid.
14570
Each
SOCKETED BADMINTON POSTS
made from special anodized aluminium
section Ø 83 mm, including height adjustable pulley, net stretching strap with
self-locking mechanism and ring screws.
Suitable for Badminton or Sepaktakraw
nets. Post length 165 cm above floor
level. Total length of post 200 cm, without
ground sockets.
56783
Each
SOCKETED Badminton POSTS
BWF standard, made of powder
coated steel tube 4 x 4 cm. The new
insert depth limitation guarantees at
all times the appropriate official net
height. Set includes pulley net sretching strap. Without ground sockets.
56773
Pair
GROUND SOCKET
aluminium with anti-corrision coating, suitable for post section 40 x
40 mm.
56782
Each
SOCKET COVER - SMALL
opening 90 mm, aluminium flange with
plastic lid.
11670
Each
Badminton Posts
with insert depth
limitation to automatically secure
official net height.
Ground Sockets
NET STRETCHING STRAP
25 mm wide nylon strap with selflocking mechanism.
56764
Each
SOCKET COVER - LARGE
opening 180 mm, aluminium flange wih
plastic lid..
14570
Each
approved
SUPPORT POST
for multiple field layouts, upright
made from aluminium tube with round
base and floor protecting pad, for net
height 155 cm.
56765
Each
GROUND SOCKET - LARGE
sections Ø 83 mm and 80 x 80 mm..
15302
Each
PORTABLE BADMINTON POSTS
BWF approved models (see ERHARD
Handbook for Sports Equipment)
35
8
FIELD AXIS
200
300
FLUSH FLOOR
82
14
102
(for Official IHF approved Goal only)
(for Official IHF approved Goal only)
102
14
82
Fixing Brackets
FIELD LINE
Aluminium Section
Handball Goal
Indoor Soccer Goal
Floor Anchorage
Handball Goal
318
Indoor Soccer Goal 519
For Indoor Soccer Goals with oval crossbar and upright aluminium section 120/100 mm
corresponding measures have to be applied.
4-POINT FLOOR FIXING
Handball Goal (DIN 7897) and Indoor Soccer Goal
Handwheel
Bracket welded on back support
Floor Plate with screw thread
Handwheel with soft rubber head
for player's safety
Ref. No. 561402
FLUSH FLOOR
4-point floor fixing requires 65 mm minimum projection of back supports!
Ref. No.
561401
Floor Plate with screw thread
and fixing screws
Dimensions in cm
HANDBALL GOAL 4-POINT FLOOR FIXING
36
handball goal
4-point floor fixing
DIN 7897-1 / EN 749 (safety requirements and test procedures)
FREESTANDING
HANDBALL GOAL 300 x 200 cm,
4-POINT FLOOR FIXING,
FIXED back supports.
Goal frame made of 80 x 80 mm
special aluminium section, including
wear-resistant safety net holders with twin
hooks, bottom of uprights with plastic floor
pads. Solid cast aluminium corner joints with
double safety screw connections (8-fold per
corner). Additional corner reinforcement by
special molded three-dimensional net support adapters that gives absolute strength
to withstand even the hardest impact. Back
supports are made of tubular powder
coated steel. Goal depth at bottom 125 cm.
Without net.
Goal Frame silver anodized
562552 black alternating tape 562562 red alternating tape
Each
Each
Goal Frame white powder coated
561502 black alternating tape
561492 red alternating tape
Each
Each
freestanding
handball goal 300 x 200 cm,
HINGED back supports, otherwise as
above, without net.
Handball Goal
Ref. No. 562552
Each
Each
561512 black alternating tape Each
Each
Official Goal
IHF Official Handball Goal Ref. No. 562761
4-Point Floor Fixing for Handball Goals
Handball Goal Ref. No. 562572
HANDBALL GOAL, IHF approved,
as used for Olympic Games 2004
and World Championship 2007.
Same construction as standard goal
with fixed back supports, but depth
on top 125 cm, at the bottom 150 cm,
without net.
562731 blue alternating tape
Each
Each
Each
Each
562761 blue alternating tape
Each
goal trolley
for transport & storage of 2 handball
goals with hinged back supports.
Sturdy tubular steel construction,
powder coated, with 4 swivel casters.
The goals rest on lateral brackets for
easy transport and storage.
44100 Standard Model
Each
44101 for max. 2 m access clearance Each
Bracket
Floor Plate
floor plate
for later installation on gym floor.
Galvanized circular plate with screw
thread and 4 boreholes for fixing
screws.
561401 Each
Special Trolley
for max. 2 m access
clearance. No. 44101
Standard Trolley Ref. No. 44100
SAFETY SCREW
with soft rubber handwheel.
561402
Each
37
8
FIELD AXIS
200
300
FLUSH FLOOR
Dimensions in cm
50
50
Floor Anchorage
Aluminium Section
Handball Goal
Indoor Soccer Goal
FIELD LINE
Floor Anchorage
Handball Goal
308
Indoor Soccer Goal 508
2-POINT FLOOR FIXING
Handball Goal (DIN 7897) and Indoor Soccer Goal
Handwheel
FLUSH FLOOR
Anchor sleeve
FLUSH
CONCRETE SLAB
1) Floor Anchor
to dowel on concrete slab,
including safety goal attachment screw with elastic rubber handwheel.
No. 56142 + 561421
Stud Anchor M10
K-0635 058
Installation Example:
Anchor sleeve bolts directly to the concrete slab (see image 1).
2) Floor Anchor
to set in concrete slab,
including safety goal
attachment screw with
elastic rubber handwheel.
No. 56146 + 561421
HANDBALL GOAL 2-POINT FLOOR FIXING
38
3) Floor Anchor
for later installation in
existing gym,
with special dowel and
floor plate, including
safety goal attachment
screw with elastic rubber
handwheel..
No. 56136 + 561421
handball goal
2-point floor fixing
DIN 7897-1 / EN 749 (safety requirements and test procedures)
freestanding
FIXED back supports.
wear-resistant safety net holders with twin
hooks, bottom of uprights with plastic floor
pads. Solid cast aluminium corner joints with
double safety screw connections (8-fold per
corner). Additional corner reinforcement by
special molded three-dimensional net support adapters that gives absolute strength
to withstand even the hardest impact. Back
supports are made of tubular powder
coated steel. Goal depth at bottom 125 cm.
Without net.
Handball goal with short back supports
(permitted for limited room circumstances only!)
Each
Each
Each
Each
freestanding
HINGED back supports, otherwise as
above, without net.
Each
Each
Each
goal trolley
for transport & storage of 2 handball
goals with hinged back supports.
Sturdy tubular steel construction,
powder coated, with 4 swivel casters.
The goals rest on lateral brackets for
easy transport and storage.
44100 Standard Model
Each
44101 for max. 2 m access clearance Each
FLOOR ANCHOR
to dowel on concrete slab, including safety
fixing screw with elastic rubber handwheel
(Mind height and kind of floor construction!).
56142 Each
SOCKET COVER – SMALL
for sprung or multi-elastic floor, clearance hole 90 mm, aluminium flange with
plastic lid.
11670
Each
goal transporters
for freestanding indoor handball/soccer
goals with fixed back supports. Sturdy
steel construction with 4 swivel casters.
12630
Pair
Special Trolley
for max. 2 m
access clearance.
No. 44101
Standard Trolley No. 44100
MINI HANDBALL goal 300 x 160 cm,
same construction as competition goal
but clear height 160 cm only. Crossbar
and uprights silver anodized, without net.
561351
Each
39
200
8
HANDBALL GOAL IN GROUND SOCKETS
300
FLUSH FLOOR
HANDBALL GOAL WALL RETRACTABLE
Flush floor slab
Detail:
Floor Slab Recess
33
electric
about 500
cable winch
25
FIELD AXIS
FLUSH
FLOOR
FLUSH
FLOOR
Distance about 200 cm for hall length 44 m
Distance about 250 cm for hall length 45 m
3080
Dimensions in cm
Aluminium Section
Handball Goal
Indoor Soccer Goal
Design load for wall retractable
handball goal:
According to DIN 18032 part 6
a vertical load Pv = 3000 N
and horizontal load Ph = 3000 N
per each wall console
must be considered.
HANDBALL GOAL – IN GOUND SOCKETS • RETRACTABLE
40
handball goal
wall retractable
HANDBALL GOAL 300 x 200 cm,
retractable by electrical winch.
wear-resistant safety net holders with
twin hooks, bottom of uprights with
plastic floor pads and push bolts
for secure floor fixing. Solid cast
aluminium corner joints with double
safety screw connections (8-fold per
corner). Hinged tubular wall supports,
including wall mounted winding device
with electrically operated cable winch,
all steel parts are powder coated.
Without net.
Each
Wall retractable handball goal No. 562421
in storage position
Wall retractable
handball goal No. 562421
in ready to use position
Ref.No. 59520
Electrical supply lines
to be provided
by the customer on-site
handball goal
with linear lifting device
Ideally combined with ceiling
mounted basketball backstop
safety lock
in case of totally broken pull cables or
pull straps.
59520 Each
Handball GOAL 300 x 200 cm,
in ground sockets, without net supports, for free hanging net. Goal frame
made of 80 x 80 mm special aluminium
section, including wear-resistant
safety net holders with twin hooks.
Solid cast aluminium corner joints
with double safety screw connections
(8-fold per corner) and additional flat
iron angle in the rear profile channel.
Without ground sockets and net.
Each
ground socket
15302
Each
with plastic lid.
14570
Each
Handball goal
in play position
Handball goal lifted
in rest position
handball goal
with linear lifting device
This goal is specially designed for small
sports halls where the distance between
the goal posts and the wall is very close
(depth between 50-100 cm). Due to the
specially designed hinge mechanism
the total depth in lifted position does not
exceed 50 cm. Due to the little space
needed for this style of goal there are
no collision points when using ceiling
mounted basketball backstops at the
same time.
optional
Each
41
protective netting
wall fixed curtain type
SUPPORTING DEVICE
for protective netting, consisting of 2
supporting brackets, projection approx. 130 cm, including tensioning wire,
distance between brackets max. 15 m.
20010
Each
Design load for protective netting
Load assumptions:
Per console a vertical load
of Pv = 2000 N per bracket
(max. distance between brackets 4 m)
horizontal Ph = 1000 N on guide rail
TRACK WAY
special track way section No. 100, with
supporting pipe 60 x 30 mm, including
runners and supporting brackets, powder
coated, projection approx. 130 cm.
20011
per metre
LOCKING DEVICE
for fully drawn netting, including disengaging device (applicable for # 20011
and # 20012 only).
20013
Each
HOISTING DEVICE
for stored netting, consisting of cable pulley
with hooking eye, 8 mm braided hemp rope
with snap hook and rope winder.
171815
Each
Hoisting device
Mesh
width
NOTE
15 % have to be added to
the length of the netting
compared with the actual
cover space.
Netting material
45 mm
100 mm
130 mm
45 mm
100 mm
130 mm
High-strength PP * High-strength PP * High-strength PP *
High-strength PP * High-strength PP * High-strength PP *
Thickness
2.3 mm
2.3 mm
3.0 mm
3.0 mm
3.0 mm
3.0 mm
Colour / Art. No.
green
green
green
white
white
white
SUPPLEMENTARY
EQUIPMENT
Nylon Rings (fixed on netting) to hang
netting and for easy sliding on steel
wire, 3 rings per metre.
21710
per m
21711 Nylon rings extra Each
Net Bordering, reinforcing edge for
protective netting (especially recommend
for tensioned netting).
21717 Nylon 8 mm thick
per m
21718 Nylon 12 mm thick
per m
42
Projection
approx. 130 cm
Track way
Disengaging
pull rope
Bracket
Hoisting rope
Rope winder
Netting
Net height
Weight Band for lower edge of netting,
lead balls worked in webbing.
21705 400 g/m
per m
21706 200 g/m
per m
21707 200 g/m, without webbing per m
white 20001
white 20003
–
–
–
–
ot-le–ss
–kn
–
–
* ) These nets are provided with a 5-7 mm diameter bordering all around.
Net length
Distance between brackets max. 4 m
20000
20002
20903
21600
21602
21603
Hoisting rope
Snap hook
protective netting
electrically operated
Supply lines for electric motor
note
cable winch No. EM221
15 % have to be added
to the length of the
netting compared with
the actual cover space.
AC 230 volts • power 0.31 kw
mains to switch-key . . . . 3 x 1.5 mm2
switch-key to motor
deadman system . . . . . . . 4 x 1.5 mm2
DIN 18032-1 Pt. 5.1.3.
Separator Netting.
Mesh widths must be
designed < = 40 mm
netting width
Band reel
Netting material
Art. No.
40 mm
45 mm
45 mm
100 mm
100 mm
nylon 2.0 mm, white nylon 2.0 mm, white
nylon 2.5 mm, white
nylon 2.2 mm, white nylon 2.5 mm, white 20300
20310
20315
20320
20325
knotted
Bracket
Guide band
Netting
Netting height
Shaft with tube motor
Mesh
width
HOISTING DEVICE
for protective netting. Power operated system consisting of a multi ball
bearing tubular shaft with band reels
every 100 cm, including guide band for
interlacing into the netting. Electric motor
with built-in limit switch, without electric
supply lines and installation.
20100 for 10 m netting width
Each
Each
Each
Weighting bar
43
Example: Posture mirror 200 x 400 cm with adjustable ballet barre
Guide rail
for height adjustment
of ballet barre
Ballet barre
Cantilever
support bracket
B
B
A
A
View A - A
View B - B
Mirror framework
(wood or
aluminium)
Wooden ledge
Mounting ledge
Guide rail
Mirror frame
(wooden or
aluminium)
Mounting ledge
Wooden ledge
with rear ventilation
WALL MIRROR SYSTEM »SECURE«
44
SPORTS MIRROR
„SECURE“
NOTE
The viewer’s visual appearance in the
mirror must be impartially evaluated
since there is no existing specification.
The planimetry of the mirror as well as
the substructure and the installation are
executed according to the EURO standard 1036 and the regulations for mirror
installations. Since the installation of a
mirror of that dimension can technically
not be provided precisely even without
any tolerances, distortions or staggered
reflections are possible.
The installation of such wall mirrors requires stable walls for inserting dowels
to fix the soft wood timber frame which
is bolted to the wall.
SPORTS MIRROR »Secure«,
20 mm, distortion-free brilliant surface
and polished edges. Available for any
room width due to variable production.
(Test certificate for shock and breaking
resistance No. 410261288)
81130 per m2
WOODEN MIRROR FRAMING,
varnished, section 60 x 16 mm, with
mounting ledge 40 x 20 mm.
81134 natural spruce
per m
81135 natural beech
per m
ALUMINIUM MIRROR FRAMING,
section 6 x 60 mm, optional RAL colours (to be specified), with mounting
ledge section 40 x 20 mm.
81136 per m
Barre supports
made from
high-grade
stainless steel
for brilliant
appearance
and utmost
stability.
FOLDED PORTABLE
POSTURE MIRROR
WITH TEST CERTIFICATE
FOR SHOCK AND BREAKING
RESISTANCE
NO. 410261288
THE MIRROR SYSTEM ALLOWS CANTILEVER SUPPORT
BRACKETS WITH INTEGRATED HEIGHT ADJUSTABLE RAILS
Stainless sleeve
for ballet barres
FOLDING PORTABLE POSTURE MIRROR
»SECURE« , 8 mm, distortion-free brilliant surface,
folded dimensions 200 x 196 cm, unfolded 400 x
196 cm (with test certificate for shock and breaking
resistance No. 410261288).
81139 Each
45
CLIMBING
REFERENCES
Zary, Poland, Ice Rink
• Climbing- and Bouldering Wall
• Climbing Wall: 7.5 m x 7 m (WxH)
• Climbing Area: 59 sqm
• Features 6 TopStop Rope Brakes
• Bouldering Wall: 5 m x 3 m (WxH)
Geraardsbergen, Belgium
PROVINCIAAL DOMEIN „DE GAVERS“
• Freestanding
Boulderand
Climbing Tower
„Bad Godesberg“
• Footprint: 2.8 m x 3.75 m
• Height: 7.5 to 7.75 m
• Features 10 TopStop Rope Brakes
• The Tower already provides protection against unauthorized
climbing. Climbing handholds can only be used up to an height
of 2.5 m. From 2.5 m up to an height of 3.75 m circular inserted
inner climbing handholds are installed, which can be locked from
the inside of the tower.
1
Soft Landing Mat
1 polyester
foam, cover made of hard-wearing Trevira material,
colour: Blue. 250 x 250 x 25 cm.
43105
Piece Belt
2 Fixing
fixing Belt for Crash Mats in front of Climbing Walls
made of PP, 4.5 m long, 25 mm wide, with 2 hook brackets and steel belt
clamp. Supply includes fixing hardware.
Can be locked by optional padlock.
Paderborn, Germany
• Climbing Wall: 13.4 m x 10.9 m (WxH)
43160
3
2
4
3
Dubai, UAE, Repton School
• Retractable Climbing Wall: 4.2 m x 5.5 m (WxH)
Fixing belt
43161
Padlock
Piece Piece Safe
4 Quick
professional fastening system for soft landing mats. Lockable wall
strap in different lengths to fasten a soft landing mat as protection for
a climbing wall, as wall collision protector as well as protection against
unauthorized use.The wall straps are available with left or right lock. Each
fastening system includes 2 straps, 2 locks with cover and 2 padlocks.
43162 2 straps, each 3.5 m long
Lock left
Set 43163 2 straps, each 3.5 m long
Lock right
Lock left
Lock right
Lock left
Lock right
Set CLIMBING
CLIMBING
SYSTEM CLIMBING WALLS
Climbing Wall
1 School/Group
MITTELGEBIRGE
NEW
School- and Club Climbing Wall for highest
demands.
System climbing unit with upright and overhanging
areas as well as an interesting bug- and triangle roof.
The unit is designed to meet beginner and advanced
user requirements.The dimension of the climbing wall
enables a class of 20 participants to practice on the
climbing wall at the same time. The climbing unit is
available with or without lifting device. Equipped
with TÜV-approved panel system, 10 TopRope deflections and 10 ropes, statics according to DIN EN 12572,
TÜV-approved climbing handholds.
ClimbingWall Safety:Electrically operated lifting device
or alternatively mat- and fastening system.
Height
Width
Climbing Area
71462
5,50 m 12,40 m
74,70 m2
71463
7,00 m 12,40 m
98,00 m2
System Climbing Wall
2 ZUGSPITZE
Retractable Beginner Wall
System climbing unit with each upright and overhanging area and two inner electrically lifted climbing
areas. Equipped with TÜV-approved panel system,
4 TopeRope baffles and 4 ropes, statics according to
DIN EN 12572, TÜV-approved climbing handholds.
ClimbingWall Safety:Electrically operated lifting device.
Height
Width
Climbing Area
71460
5,68 m
4,96 m
29,10 m2
71461
7,00 m
4,96 m
38,80 m2
2
1
School/Group Climbing Wall MITTELGEBIRGE
System Climbing Wall ZUGSPITZE
3
System Climbing Wall WATZMANN
Overhang
Vertically
Climbing Wall
3 System
WATZMANN
Fixed Beginner Wall
System climbing unit with upright and overhanging
area. Features TÜV-approved panel system, 4 TopRope
baffles and 4 ropes, statics in accordance with DIN EN
12572, TÜV-approved climbing handholds.
Climbing Wall Safety: Mat- and Mounting system.
Height
Width
Climbing Area
71455 5,50 m
4,96 m
29,10 m2
71456 7,00 m
4,96 m
38,80 m2
Climbing Wall
4 System
DACHSTEIN
System climbing wall unit with complex arranged
climbing area featuring an upright and overhanging
area as well as an interesting bug and roof. Suitable
for PE-lessons at continuing schools and club sports.
Equipped withTÜV-approved panel system, 4TopRope
baffles and 4 ropes, statics according to DIN EN 12572,
TÜV-approved climbing handholds.
Climbing Safety: Mat- and Mounting System.
Height
Width
Climbing Area
71457 5,50 m
4,96 m
35,20 m2
71458 7,00 m
4,96 m
47,80 m2
Liftable
Individual Climbing Walls
Besides the standard climbing walls On Top climbing also
offers individual/customized climbing walls. For this purpose many modules are available which can be combined
with each other. Modular climbing walls are suitable for all
kinds of practices. Structure and degree of difficulty of the
wall can be implemented according to requirements and
the particular use and being further developed due to the
modular structure. The modules are available for in- and
outdoor use. All modules are available with a width of 1.24
m (1 rope deflection) or 2.48 (2 rope deflections). Also,
customized sizes are available. Next to the standard heights
of 5.50 m and 7.00 m for sports halls also in other heights
available. Following standard modules are available: Upright,
Overhang, Double Overhang, Roof, Bug and Triangle Roof.
All school and system climbing walls are also available with
electrically operated lifting device.
Individual Heights, Widths, and Extra
Equipment available upon inquriy.
4
System Climbing Wall DACHSTEIN
electric
cable
winch
approx.100
Netting
Belt strap
Sight screen
up to 2.50 m height
divider curtains and division netting:
Per console/suspension (max. distance
4 m) in the net axis.
PV = 2000 N
PH = 1000 N
Dimensions in cm
We manufacture and install divider curtains and division
nettings with sightscreen for any type of sports hall, gallery
protection netting, etc.
Please provide us with the required details of your project
(layout and cross section or just length and height of the
curtain). We will submit our estimate shortly.
DIVIDER CURTAINS WITH SIGHT SCREEN FOLD-UP TYPE
48
divider curtain light model
lifting type with folding sight screen
Gymnasium of the German School
in Singapore separating sports hall
into two sections with our lightweight
divider curtain (opaque up to 2 m
height, over and above netting)
divider curtains heavy model, double-walled
lifting type, sound absorbing
Full height double-walled divider curtains will be
offered and installed by our co-operating partners.
49
locker room benches STANDARD
Locker Room Bench Standard
• Sturdy construction in standard length of 2 m or customized length up to 2.70 m
(on request).
• Shapely design of square steel tube 25 x 25 mm, Platinum Grey (as RAL 7036)
powder-coated1, shoe rack* (also to retrofit) made of thick-walled aluminium tube.
• Seat Laths, Backrests and Coat Rails are manufactured of solid knotfree, glued
softwood, natural varnished
• Upon request: Glued hardwood (subdued beech)* /coloured varnish*
• Double coat hooks made of plastic
• Legs feature floor protecting plastic endings for levelling
• Components are pre-assembled, for easy self-assembly.
• Size: Length 200 cm or customized length up to 270 cm, Seat Depth from to 33.6 cm,
Seating Height 45 cm, Overall Height (incl. coat rails): 165 cm.
*
) Surcharge
Manufactured
by Erhard Sport
Locker Room Bench STANDARD
1
Type D
With Backrest
Coat Rail
For the production of our
gymnastic apparatus and
sports equipment we solely
use lumbers from sustainable
foresting in Europe.
Considering the very long
useful life of our sports equipment of more than 40 years,
the cost effectiveness when
buying a product "Manufactured by Erhard" is evident.
Find out for yourself and visit
our production facility.
Type A
without Backrest
Type E
With Backrest,
for Wall Mounting
Hooks
Double hooks made of plastic with
bolt-on plate.
Back View
Customized Lengths (up to 2.70 m)
Manufacture according to drawing, delivery and
installation as per offer.
Standard Length 2 m (Self-Assembly)
Type A
without Backrest
Type A
without Backrest
29440
29450
Without shoe rack DIN Per Meter
With shoe rack
Per Meter
29390
29391
Without shoe rack DIN
With shoe rack
Type D
With Backrest
29460
29465
Without shoe rack DIN Per Meter With shoe rack
Per Meter Type E
for Wall Mounting
with backrest, without coat rail, ideal for mounting
above radiators.
29425
Per Meter
50
for easy self-assembly thanks to pre-mounted
(factory-provided) seating, incl. screws.
Piece Piece Accessories:
1
Coat Rail
for Form A, D and E.
29458
Per Meter
locker room benches STANDARD
Accessories:
Customized Locker Room Benches?
Are you planning to furnish your locker room with benches and do not know how many of them
you need? Please send us the layout of the particular room showing location of doors, windows and
radiators. We will then prepare for you a customized offer with our furnishing suggestions for you.
Rail
1 Coat
made of knotfree, glued softwood made of plastic. Suitable for
mounting on locker room benches Type A, D and E. Customized Lengths
up to 2.70m.
29458
Per Meter For a safe attachment of
the locker room bench to
the wall, ideally between
seat planks and backrest!
Wall Attachment Device for Locker Room Benches
for type A, B and D. For attachment on concrete and lime sand brick
walls. The wall attachment secures the bench from shifting, stealing and
reduces danger of tipping over.
29421
Pair Type B
Type C
on One Side
Two-Sided
Customized Lengths (up to 2.70 m)
Manufacture according to drawing, delivery and
installation as per offer.
Standard Length 2 m (Self-Assembly)
Type B
Type B
With Backrest and Coat Rail, on One Side
29420
29430
Without Shoe Rack, DIN Per Meter With Shoe Rack
Per Meter Type C
With Backrest and Coat Rail, on Two Sides
29470
29480
Without shoe rack DIN Per Meter With shoe rack
Per Meter for easy self-assembly thanks to pre-mounted
(factory-provided) seating, incl. screws.
With Backrest and Coat Rail, on One Side
29392
29393
Without shoe rack DIN Piece With shoe rack
Piece Type C
With Backrest and Coat Rail, on Two Sides
29394
29395
Without shoe rack, DIN
With shoe rack
Options for Seat Slats
I
Hardwood* (steamed beech),
varnished
II
Pine*, painted
(choice of colours)
III
Pine*, varnished
I
II
III
*Finger-jointed
Piece Piece 51
Indoor and Outdoor Sports Equipment –
professionally designed, manufactured and installed.
Our Service Team at your disposal for orders and queries.
Address: ERHARD SPORT INTERNATIONAL
Im Grund 2
91593 Burgbernheim | Germany
Hotline: +49 9843 9356-130
Telefax: +49 9843 9356-181
E-Mail: [email protected]
Online: www.erhard-sport.com

- Katib Technologies

Transcription

Similar documents

Trip to Chudleigh`s Farm

Product sheet BBPE050.4A

HEAVY SPECS. CLEAR VIEW.

Guardian GLHL-SS GLHR-SS

1335BT - ADP Lemco

NCAA SPECS

Rear Fold, Rear Braced, Bent Mast

Aluzinc - what is it? ASD metal services

www.alubond.com Aluminium composite panels for facade cladding

ANDREW, SANDBURG AND STAGG HIGH SCHOOLS Orland Park