PLIOLITE DF™ 01L

Transcription

PLIOLITE DF™ 01L
Oil & Gas
Technical Data Sheet
PLIOLITE DF ™ 01L
KEY ADVANTAGES
Latex Polymer Fluid Loss Control Additive for
Oil and Synthetic Based Drilling Fluids
- Provides tight fluid loss control
TYPICAL PROPERTIES
- Better dispersibility than powders in organic fluids,
activating at low temperatures and with weak
base oils
PHYSICAL PROPERTIES
- Contributes to low shear viscosity (even at high
temperatures), reinforcing the suspension properties
of the mud
Activity (% by weight)
Specific gravity
pH
Bulk density (lb/gal)
Brookfield viscosity (mPa·s)
(LVT #2 spindle at 60 rpm,
room temperature)
Moisture (%)
- Recoverable in recycled drilling fluids
- Safe for marine life when used as intended
APPLICATIONS
0.50
CHEMICAL/MECHANICAL PROPERTIES
- HTHP fluid loss control additive with secondary rheological contribution
- Suitable for use in non-aqueous drilling fluids
(diesel, esters, LTMO, iso-olefins) at bottomhole
temperatures of 300–400 °F (149–204 °C)
40–45
1.01
8–12
8.35
<250
Mechanical stability
Freeze point (°F/°C)
Multivalent ion stability
Foam
Emulsifier
Solubility in organic fluids
Excellent
32/0
Excellent
Low
Anionic
Swells in most aromatic
and aliphatic base oils
PROCESSING INFO
•Recommended loading at 1.0–8.0 ppb
•Should be added slowly under shear before the brine after emulsifier(s) has been added to the drilling fluid
•Should be tested in complete fluid with fines to optimize fluid loss, plastic viscosity and high temperature, high pressure (HTHP) rheology
PACKAGING, HANDLING AND STORAGE
•
Packaging: Tank truck, 2,200 lb (998 kg) totes & IBC, 465 lb/55 gal (211 kg/208 L) plastic drums, 72 drums in a
20 ft shipping container
•
Handling: Protect latex from freezing. This product is freeze-thaw stable, however best practice with any latex is to limit
the number of cold cycles. Keep container(s) sealed until content is ready to be used to avoid freezing and/or introduction of bacteria. Thawed material should be tested for drilling fluid performance before use. Mildly stir (low pitch blades,
50 rpm) and mix well before using.
•
Storage: The recommended storage temperature is 40–120 °F (4–49 °C). For bulk storage, use stainless steel
(304 or better) or plastic tanks. Minimum shelf life is 12 months when stored as recommended.
•
For additional information refer to the Latex Handling and Storage Guide as well as SDS documents. A SDS may be
obtained by contacting your Account Manager.
Continued on reverse
Oil & Gas
Technical Data Sheet
PLIOLITE DF 01L
Latex Polymer Fluid Loss Control Additive for
Oil and Synthetic Based Drilling Fluids
OTHER INFORMATION
•
All of the substances in this product are considered registered under REACH because they were notified under the
previous law or have been pre-registered.
•
Has no adverse effects on marine life as demonstrated by tests conducted in accordance with the recommendations of
the Oslo and Paris convention for the Prevention of Marine Pollution Program and Measure Committee.
•
ECCN number: EAR99
www.omnova.com/oilgas
NOTE: Although the data supplied above is believed to be accurate, each user is advised to make an independent determination
as to whether the described product(s) is/are appropriate for a particular use or application, whether such use will comply with all
applicable laws or regulations, or whether such use will infringe the intellectual property rights of third parties.
World Headquarters
25435 Harvard Road
Beachwood, OH 44122 USA
PHONE
+1 216 682-7070
FAX
+1 216 453-0108
CUSTOMER
SERVICE
+1 888 253-5454
EMAIL
[email protected]
Oil & Gas Headquarters
1505 Highway 6
Suite 300
Houston, TX 77077 USA
PHONE
+1 832 432-2110
EMAIL
[email protected]
Europe / Middle East /
Africa / India
14, avenue des Tropiques
Z.A. de Courtaboeuf 2 - Villejust
91955 Courtaboeuf Cedex
France
PHONE
+33 (0) 1 69 29 27 00
FAX
+33 (0) 1 69 29 27 01
Asia Pacific
100 Beach Road
#24-06 Shaw Tower
Singapore 189702
PHONE
+65 6391-0190
FAX
+65 6291-0334
ALL OMNOVA PRODUCTS AND SERVICES ARE OFFERED AND SOLD SUBJECT TO THE OMNOVA STANDARD TERMS AND CONDITIONS OF SALE AGREEMENT SET FORTH AT WWW.OMNOVA.COM.
All trademarks - OMNOVA Solutions.
© 2015 OMNOVA Solutions. April 2015

Similar documents

Global Drilling Fluids Market Projected to Reach $ 8.34 Billion by 2018

Global Drilling Fluids Market Projected to Reach $ 8.34 Billion by 2018 Drilling fluid is used to aid the drilling of boreholes into the earth. Drilling fluids includes synthetic based fluids and oil based fluids on the base of classification, which represent 24% and 37% of global drilling fluids market.

More information

Drilling Fluids Market Analysis, Growth and Demand Forecast to 2020 by P&S Market Research

Drilling Fluids Market Analysis, Growth and Demand Forecast to 2020 by P&S Market Research The global drilling fluids market is developing exponentially because of the rising worldwide vitality request, the shale blast, and deep-water drilling exercises. Attributable to exhausting coastal reserves the market is moving its center towards growing offshore areas. This expands the general cost and prompts the utilization of all the more drilling fluids which thusly creates higher income for drilling fluid producers.

More information