Receives Full Ka-Band 17.30-22.00 GHz simultaneously
Transcription
Receives Full Ka-Band 17.30-22.00 GHz simultaneously
SMW Ka Quad/Triple/Dual Band System ReceivesFullKa-Band 17.30-22.00GHzsimultaneously The Ka Band System consists Ka LNA Wideband, Ka splitters, Ka BDC’s and matched Ka cables. Comes standard with Low Phase Noise to meet DVB-S2X Professional services. Options include customized LO’s, customized frequency ranges, customized gain, separate DC power input and separate input for the external 10 MHz reference. All parts are optimized, adjusted, matched and tested as one complete unit. Quality and long term reliability is also essential. The system is therefore tested according to a very extensive test program, which includes heating, cooling, waterproof testing and rigorous electrical testing. Swedish Microwave was founded 1986 and is today a leading manufacturer of professional LNBs (Low Noise Block converters). The company is located in Motala Sweden, and to date the products are installed in more than 122 countries. All work is in-house allowing custom-design products, short delivery times, high flexibility, quick service and support. Swedish Microwave AB | Dynamovägen 5 | 591 61 Motala | SWEDEN | Tel. +46 141 216135 | Fax. +46 141 215224 | [email protected] | www.smw.se SPECIFICATION SMW Ka Quad/Triple/Dual Band System SMW Quad Band System 17.30-22.00 GHz Frequency range LO frequency IF LO 16.35 GHz 17.30-18.50 GHz 16.35 GHz 950-2150 MHz LO 17.55 GHz 18.50-19.70 GHz 17.75 GHz 950-2150 MHz LO 18.75 GHz 19.70-20.90 GHz 18.75 GHz 950-2150 MHz SMW Triple Band System 17.70-21.20 GHz Frequency range LO frequency IF LO 16.75 GHz 17.70-18.90 GHz 16.75 GHz 950-2150 MHz LO 17.95 GHz 18.90-20.10 GHz 17.95 GHz 950-2150 MHz LO 19.15 GHz 20.10-21.20 GHz 19.15 GHz 950-2050 MHz General specification Gain nominal Gain flatness within 30 MHz max. Gain flatness over each band max. Gain variation from nominal value max. Noise Figure, typ. LO Phase noise typ. LO leakage RF input Image rejection P1dB typ. IP3 typ. Input LNA Input BDC Output (waterproof) Input VSWR Output VSWR Operating temperature Storage temperature Dimensions BDC F-connector N-connector Weight DC BDC Power typ. BDC DC power LNA Power consumption LNA Dimensions Weight Internal reference LO stability 60 dB / custom made ±0.4 dB ±2 dB ±4dB 2 dB -40 dBc @ 10 Hz -65 dBc @ 100 Hz -85 dBc @ 1 kHz -90 dBc @ 10 kHz -95 dBc @ 100 kHz -112 dBc @ >1 MHz -60 dBm 30 dB min +15 dBm +25 dBm WR 42 (Flange PBR220, M3 threaded mounting holes) SMA F-connector 75 ohm, N-connector 50 ohm or SMA-connector 50 ohm 2.3:1 typ. (option 1.5:1 with isolator) 2.1:1 typ. -40 to +80°C -40 to +80°C 155 x 80 x 44 mm 161 x 80 x 44 mm 399 g (F- & SMA-connector) 418 g (N-connector) +12 to +24 VDC (LO 18.75 GHz +13 to +24 VDC) 5W 10-26V / 110 mA typ. via one of the RF output connectors or via sep. SMA-connector (bottom side) @12V- 1.32W, @24V-2.64W 77 x 46 x 34 mm 124 g ±1 ppm -40° to +60°C (±1.5 ppm -40° to +80°C) or ±2.5 ppm -40° to +60°C (±3.5 ppm -40° to +80°C) Long term LO stability over all conditions LO Stability ±1 ppm LO Stability ±2.5 ppm External 10 MHz reference LO stability External reference input frequency External reference input power External reference input port Options LO 19.95 GHz 20.90-22.00 GHz 19.95 GHz 950-2050 MHz ±3 ppm ±6 ppm Depend on the external reference 10 MHz -15 to +5 dBm Output IF connector. Option via sep. connector (SMA, N or F) Separate DC power input (SMA, N or F) Customized gain and variation Customized LO frequency and frequency ranges Separate input connector for the ext. 10 MHz ref. The standard Quad system consists of: 1 pc Ka-Band LNA Dual Output SMA 2 pcs Ka-Band splitters 6 pcs Ka-Band SMA-cables length 1.5 m 4 pcs BDC’s 1 pc DC cable from Low band BDC to LNA 3.3 m Specifications are subject to change without notice. General terms Orgalime S 2012. Products from Swedish Microwave AB are made for commercial use. 2015-03-04 Dynamovägen 5 | 591 61 Motala | SWEDEN | Tel. +46 141 216135 | Fax. +46 141 215224 | [email protected] | www.smw.se