QCS-QuickCover-Floor-Wall-expansion-Joint-from-EMSEAL-TD 2014 patented

Transcription

QCS-QuickCover-Floor-Wall-expansion-Joint-from-EMSEAL-TD 2014 patented
Quickcover Tech Data
APRIL 2014, Page 1 of 1
www.emseal.com
®
TECH D
A
QuickCover
T
Precompressed, anchorless, rapid installation floor and wall expansion joint cover.
A
US Patent 6,532,708
Features
• No visible coverplate screws
• No visible anchoring fasteners
• Flush with floor retrofit into old hardware of failed joint systems
• Bridges and conceals cracked adjacent flooring
• Resists pedestrian and rolling point loads
• Install while occupied using simple traffic diversion
• Install after flooring is installed, leveled and completed
• Cost effective
• Shipped in 10-LF lengths
• ADA compliant bevel and coefficient of friction
• Rapid installation—new or retrofit
• No bolts, anchors, balls, tracks, slides or other fiddly hardware
• No blockouts, recesses, or backfilling
• Aesthetically and practically versatile
QuickCover
10-ft (3m) of rapid install,
invisibly anchored, floor and
wall coverplate system.
Product Description
Uses
QuickCover is a rapid install, elegantly simple, aesthetically
versatile coverplate system for new and retrofit floor and wall
expansion joints.
Bridges and seals floor and wall joints in new and retrofit
construction for schools, hospitals, airports, offices, malls, etc.
QuickCover is supplied in 10-LF lengths and is a composite
assembly of precompressed foam that flanks a vertical spline
descending from an integral coverplate.
Installation Summary
The assembly is packaged between extruded polystyrene and
the precompressed foam is held in compression to less than
the intended joint size.
The joint is prepared, a mounting bead of supplied silicone is
applied to each joint face and tooled flat, the shrink wrap is
removed and the assembly is lowered into the joint.
Weight is applied to the coverplate until the foam has self-expanded into the wet mounting silicone.
Within about one hour the joint is trafficable.
QuickCover in precompressed packagaing.
Movement Capability
• Total 100% (+50% and -50%) of nominal material size.
Coverplate Material/Finishes
• Standard finish is sand-blasted Type 6061 T-6 Aluminum
• Other finish options are available and will affect lead time.
• Finish options include: Mill Finish; Blast/Anodized; Brush/
Anodized; and Matte Anodized (consult EMSEAL)
Standard Sizes
Joint Size
1" (25mm)
1-1/4" (30mm)
1-1/2" (40mm)
1-3/4" (45mm)
2" (50mm)
2-1/4" (55mm)
2-1/2 (65mm)
2-3/4" (70mm)
3" (75mm)
3-1/4" (80mm)
3-1/2" (90mm)
3-3/4" (95mm)
4" (100mm)
Plate Width
Depth
4-inch (100mm) 2-1/2" (65mm)
5-1/2" (140mm) 2-1/2" (65mm)
7" (175mm)
2-1/2" (65mm)
Availability and Price
• QuickCover is available for shipment internationally.
• Prices are available from local representatives and/or
directly from the manufacturer.
• The product range is continually being updated, and
accordingly EMSEAL® reserves the right to modify or
withdraw any product without prior notice.
Packaging removed.
Installed into joint
opening.
EMSEAL JOINT SYSTEMS, LTD 25 Bridle Lane, Westborough, MA 01581
EMSEAL, LLC 120 Carrier Drive, Toronto, ON, Canada M9W 5R1
Warranty
Standard or project specific warranties are available from
EMSEAL on request.
Toll Free: 1-800-526-8365
PH: 508.836.0280 FX: 508.836.0281
PH: 416.740.2090 FX: 416.740.0233
Copyright © 2014 by EMSEAL JOINT SYSTEMS, LTD. All Rights Reserved

Similar documents

EMSEAL-QuickCover-TechData 1-2016 no patent

EMSEAL-QuickCover-TechData 1-2016 no patent Product Description QuickCover is a rapid install, elegantly simple, aesthetically versatile coverplate system for new and retrofit floor and wall expansion joints. QuickCover is supplied in 10-LF lengths and is a composite assembly of precompressed foam that flanks a vertical spline descending from an integral coverplate. Installation Summary The assembly is packaged between extruded polystyrene and the precompressed foam is held in compression to less than the intended joint size. The joint is prepared, a mounting bead of supplied silicone is applied to each joint face and tooled flat, the shrink wrap is removed and the assembly is lowered into the joint. Weight is applied to the coverplate until the foam has self-expanded into the wet mounting silicone. Within about one hour the joint is trafficable. Features • No visible coverplate screws • No visible anchoring fasteners • Flush with floor retrofit into old hardware of failed joint systems • Bridges and conceals cracked adjacent flooring • Resists pedestrian and rolling point loads • Install while occupied using simple traffic diversion • Install after flooring is installed, leveled and completed • Cost effective • Shipped in 10-LF lengths • ADA compliant bevel and coefficient of friction • Rapid installation—new or retrofit • No bolts, anchors, balls, tracks, slides or other fiddly hardware • No blockouts, recesses, or backfilling • Aesthetically and practically versatile Uses Bridges and seals floor joints in new and retrofit construction for schools, hospitals, airports, offices, malls, etc. Movement Capability • Total 100% (+50% and -50%) of nominal material size. Coverplate Material/Finishes • Standard finish is sand-blasted Type 6061 T-6 Aluminum • Other finish options are available and will affect lead time. • Finish options include: Mill Finish; Blast/Anodized; Brush/ Anodized; and Matte Anodized (consult EMSEAL) Standard Sizes

More information