manual berço oxford após recall

Comments

Transcription

manual berço oxford após recall
Oxford - Cot Bed
Assembly Instructions - Please keep for future reference
604/5540
614/5536
Dimensions
Width - 143,6cm
Depth - 76.5cm
Height - 98,5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Issue 2 - 26/10/16
.
.
,
when the child is able to climb out of the cot, the cot shall no longer be used for that child.
and BS 8509:2008 + A1:2011
The toddler bed is suitable for children aged from 18 months to 4 years.
Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or
present a danger of suffocation, e.g. strings, blind/curtain, cords, etc.
(63 x 76.5cm)
(45 x 76.5cm)
x 20
G
M4 x 50mm Bolt x 4
J
Washer x 4
H
55mm x 55mm Spacer
I
Nut x 4
D
D
D
D
D
01
02
E
A
B
Fix sides frames 04 to the
headboards using bolts A
and allen key B .
A
B
A
B
A
B
Do not fully tighten bolts at
this stage as side rails
need to be fixed first.
04
Attention!
Ensure mattress
mark on side
frame is facing inwards, as
shown.
A
B
A
B
A
B
04
B
A
A
B
A
B
B
Insert barrel nuts F into
the side bars 05 .
05
05
B
A
B
E
B
With help, fix side rails 05
to the first height position in
the assembled headboards
using bolts E and allen key
B .
F
F
Attention!
To the correct
position of the
side rails.
There are three height
positions in the cot for the
base, you will need to lower
the side rails as the baby
grows. Please refer to the
first page - warning section
- for more information.
B
B
B
E
B
E
B
E
B
E
B
Attention!
Finish tighten bolts
on side frames
using allen key B .
Make sure not to use
these holes while the
product is built as a
cot.
E
E
E
Step 6
cer
Fix first two slats 03 next
to the headboard and
footboard using bolts G ,
washer J and nut I
through the holes.
o
dt
ap
rg
spa
nee
no
lle
ma
s
C
Then, using spacer H
work towards the middle of
the cot fixing slats 03 to
the side rails 05 using
screws C .
Note that the slats in the
middle will have a gap
smaller than the spacer
lenght.
-
use
G
H
C
C
C
C
C
G
C
G
C
C
C
C
C
C
C
C
C
C
G
C
J
C
I
J
C
C
I
G
I
J
Important!
Cot/Bed base
must never be
dismantled once built.
J
I
TODDLER BED
Assembling toddler bed
Remove all bolts from the
headboard, cotbase and
side frames and take the
cotbed apart. Then,
remove the bolts from the
first slats next to
headboards.
B
01
E
B
B
E
B
.
Fix the first slats next to the
headboards back using
bolts G , washer J and
nut I through the holes.
Use the holes indicated in
the drawing, otherwise,
the toddler bed will not be
built according to norm
BS8509.
B
E
E
Make sure
to use the
holes
indicated in
the drawing!
E
I

Similar documents