The ISSF Equipment Control Program

Comments

Transcription

The ISSF Equipment Control Program
14TH
ISSF CHAMPIONSHIP ORGANIZERS WORKSHOP
MUNICH 2016
ISSF EQUIPMENT
CONTOL PROGRAM
TOPICS
EQUIPMENT CONTROL TESTING PANEL
Physical Requirements ( Facilities)
Staffing and Staff Training
Testing Equipment required
Pre – and Post – Competition Testing Procedures
Current Equipment Control issues
ISSF RULE BOOK AND ISSF GUIDELINES
EQUIPMENT CONTROL FACILITIES
– The area proposed for the Equipment Control should be of sufficient size to avoid congestion; – it needs:‐
– Good access and big enough
– Stabile floor is the first when you choose the location
– Needs good light and ventilation
– Close to Armoury and the ranges
– Changing Rooms on different places
– Post Competition Test Control Area – Range clock
EQUIPMENT CONTROL FACILITIES
– Please, do NOT choose a tent for equipment control, have in mind ….
– Floor quality
– Access – Climate condition
– Temperature changes
– Effect of measurements
– Requirement is a permanent Room
– Instruments are very precise and work without problem, but you can imagine the best instrument will show you wrong results if a floor or table is moving
EQUIPMENT CONTROL FACILITIES
W
M
Changing
rooms
Men and
Women EQUIPMENT CONTROL AREA- EQUIPMENT STORAGE
Short Way to the Storage
CHANGING ROOMS
Changing rooms are necessary , for Underclothing , Medical and Taping
Re Inspection
R/P
Control
– d
Taping
On each specific
range and in the
EQ station
is requred
EQUIPMENT CONTROL AREA
– One of the problem are the furniture
– Tables must be big enough and stabile
POST COMPETITION EQUIPMENT CONTROL AREA
– Testing devices should be operated in the same weather conditions as the equipment used by the athletes on each specific range. LOCATION FOR 25M RFP TESTING
Test Officer
AIR STATION WITH DIFFERENT ADAPTERS
INSTRUMENTS AND OPERATION
STAFFING AND STAFF TRAINING
Equipment Control needs a qualified experiend team .
Officers are handling with guns.
Controls in all sections must be done very accurate.
Training internaly is necessary, Rule changes, procedure,etc.
– We face problems that national Staff are comming on the official arrival day, and therfore the preparation is
behind.
– Languagge problems .
– Long working hours.
–
–
–
–
HOW IT WORKS
ISSF EQUIPMENT CONTROL PANEL COMMITTEE
The ISSF Equipment Control Panel Committee will take over the full business and
will help you to assist, advice and supervice to make sure all equipment controls
are conducted in absolutely the same way with testing protocols and standards
that are as consistent and fair as possible.
It has to be secured that there is only one way used to test machines and this way
is always the same at all Equipment Controls.
A primary objective of the ISSF Equipment Control Testing Panel will be to ensure
absolute consistency in calibrating and using the testing equipment.
ISSF EQUIPMENT CONTROL PANEL COMMITTEE
– Organizers should give the members of ISSF EC Testing Panel the
opportunity to arrive one day before the official arrival date in order
to speak with the EC officers, evaluate their expertise and train them
in order to be ready for the competition.
– To safe costs for OC, two member from the ISSF Testing Panel can
be selected for one ISSF Championship , one member can act in a
double function.
COMPETITION SCHEDULE
– Enough time between qualification and final should be scheduled in
order to be give EC staff the ability to complete the necessary post
competition checks.
– In general we have one (1) hour between qualification- finals, a
great help would be to have on each specific range a little area
prepared for the Post competition checks.
EQUIPMENT CONTROL SPIRIT
No tolerance
protection of athletes
Follow the Rules and Guidelines
elevate the status and level of authority of Equipment Control
increase the confidence of athletes
involve and cooperate with athletes
open testing in order to assure the integrity of the process
TESTING EQUIPMENT REQUIRED - ISSF SHOP
ISSF Rule 6.5
Each Organizing Committee must provide a complete set of gauges and
instruments for Equipment Control during ISSF Championships;
Have also in mind to have a spare set of instruments.
You will find all Tools and Instruments available, in our ISSF shop
INSTRUMENTS FOR RIFLE
Template for Rifle
Weighting Scale with a rated capacity of 10 kg, in 1 gram increments, with an government calibration certificate
Thickness Test Device
Stiffness Test Device
70mm Overlapping Device 6‐8Kg
Boot Measuring Gauge
Sole Flexibility Device
Steel Ruler 300mm
Kneeling Roll Template
1500gm Trigger Weight ( 300m Standard Rifle)
INSTRUMENTS
Thickness Tester
Template
Stiffness Tester
Scale
Rulers
STIFFNESS DEVICE TABLE
Courved edges
The table top must be of a material provided it does not impede with the movement of the fabric while measuring stiffness.
OTHER INSTRUMENTS
6 to 8 kg
Jacket Overlapping
Boot Testers for Rifle
Trigger weight 300m Kneeling rool device
RIFLE AND PISTOL FLEXIBILITY DEVICE
INSTRUMENTS FOR PISTOL
Weighting Scale with a rated capacity of 1.500 kg, in 1 gram increments, with an government calibration certificate
Measurement box 420 x 200 x 50 mm for air pistols
Measurement box 300 x 150 x 50 mm for centre fire and rim fire pistols
A weight for measuring trigger pull (500 gram, 1000 gram)
A Device for measuring 90° angle template for measuring the heel rest configuration on the grip
Verniers slide gauge, steel rule of 300 mm graduated in mm
Boot tester for the flexibility of the sole ,the same like rifle Velocity Testing Set
PISTOL INSTRUMENTS
Trigger weights and Pistol testing
Boxes, 10m and 25m
OR
PISTOL INSTRUMENTS
Handtools for the grips
Scale , to weight the bullets‐ 25m RFP
Angle meter‐ rulers
Velocity Testing Equipment 25m RFP
INSTRUMENTS FOR RUNNING TARGET
Template for Rifle Running Target
Weighting Scale with a rated capacity of 10 kg, in 1 gram increments, use Rifle Scale
500gm Trigger Weight ( 50m Running Target Rifle )
Scope Testing on the 10m RT Rifle
Template
Scope Tester
Trigger tester 500g
SHOTGUN INSTRUMENTS
Scale with certificate provided
by the ISSF , at least two digits are required, thee are even better
Testing calibration weight
provided by the ISSF Ammunition boxes provided by the OC
Skeet Marker Tape Test
Provided by the ISSF,
with a special Laser
NEW WAY OF MEASUREING THE SKEET MARKER TAPE
Eyes can never see if a
marker tape is on or over
The limit, the laser is accurate and is the same for everybody
The new measuring position, both arms bended,
while standing straight
NEW WAY OF MEASUREING THE SKEET MARKER TAPE
Soon the measurement is done, the data goes directly
to the computer and the marker tape will be sealed with an ISSF special seal
NEW WAY OF MEASUREING THE SKEET MARKER TAPE
SHOTGUN INSTRUMENTS
ISSF CLAY TARGET GO‐NO‐GO GAUGE
A 5 envelopes
ISSF CLAY TARGET BREAKABILITY DEVICE provided by the ISSF
ECO TARGETS
The use of eco, or eco- friendly clay targets is encouraged in all ISSF
Championships. The use of eco, or eco- friendly clay targets is required in
all ISSF World Championships and the Olympic Games.
ISSF Testing procedure
Breakability test ( ISSF test tool),
ECO test according PAH requirements ( ISSF)
IPC TESTING INSTRUMNENTS
Spring Test Device
Backrest Device
Rifle Balance Device
PRE – AND POST – COMPETITION TESTING PROCEDURES
Testing Equipment and Calibration Is most important All tools what you are using must be correct and accurate.
CALIBRATION
You will find the manual instruction about
calibration on our ISSF web side
The tools and instruments will be checked by the ISSF responsible person and she/he will bring a special testing set.
PRE – AND POST – TESTING AREA- RIFLE - PISTOL
Please make sure that a little test area is prepared on each
specific range OR if the EQ control is located in the center of the
ranges, ( like in Rio) than you don‘t need another area.
Have in mind there is only a short time between Qualification
and Finals.
You must have a spare set of Instruments in case any kind of
damage, and you will need them for post competion tests
anyway.
Please send a draft of the location in advance to our ISSF HQ ,
and we are able to help you in preparing your individual
guidelines.
PRE – AND POST – PREPARATION AREA
Must be big enaugh for all athlets
and coaches.
Chairs and table for every athlete.
Make sure that the area is secured
during the final.
A Range clock should be available.
Finals PREP area
Air Condition controller Range Clock
PRE – AND POST – COMPETITION TESTING PROCEDURES
The Pistol Trigger weight control must be conducted on the Range, a table at the
end of the range, or next to the CRO is all what you need.
The Equipment Control will escort athletes to the EQ area, ( Rifle&Pistol).
SHOTGUN TESTING PROCEDURE
PRE – AND POST TEST – SHOTGUN
During Qualification, athlets will be selected by computer draw.
• All scales what will be using , must be calibrated and tested
with a government – certified 24.5 g check weight before
testing, during testing and immediately after each test of
an overweight shot charge
PRE – AND POST TEST – SHOTGUN
S
c
a
l
e
PRE – AND POST TEST – SHOTGUN
All cardridges must be
stored and locked, and
given back to athltes after the end of the event
ENVIRONMENT AND RECYCLING
E
m
p
T
y
There are different components which can
not go in any rubish box
Primer, poweder and lead
EQ TESTING ON THE FOP IN FINALS
Table with six boxes with
covers, and able to seal
Open visible procedure
Open visible procedure
All tests must be
completed before the
presentation, and this 30 minutes before the start
of a finals.
CURRENT EQUIPMENT CONTROL ISSUES
In general the ISSF Equipment Control procedure was working
in 2016 extremely well.
Rifle Pistol Shotgun procedure was working without any
problems.
Some little minor cases we should bring it in considerations.
Is very difficult to gets the job done correctly , if tools or
instruments are not ready, not available, or wrong items.
Air Conditions are in general a problem , a lot of times it is to
cold at the 10m Range and that can be dangerous for any post
competitions checks.
CURRENT EQUIPMENT CONTROL ISSUES AND CHANGES
Sponsoring was a big issue in the Rio games, 240m of masking tape had
been used.
We use very expensive and very nice sport equipment.
We have to bring it in consideration that pictures are done everywhere in
qualification rounds , not only in finals, and this pictures goes round.
Tape was also used to add weights, on rifle stocks, butt plates , etc.
Shooting vests must not be constructed with any item (tape, drawstring,
elastic band, etc.) that could be used to adjust the fit of the jacket.
CURRENT EQUIPMENT CONTROL ISSUES
Breakability and invironment
Athlets train very hard and we must give them the most
best conditions in all trainings and competitions
THANK YOU VERY MUCH

Similar documents