Swisslog`s TransLogic pneumatic tube systems transport carriers

Transcription

Pneumatic Tube
System Accessories
SWISSLOG
SPECIFICATIONS
TRANSMISSION
COMPONENTS FOR
TRANSLOGIC
PNEUMATIC TUBE
SYSTEMS
The remote arrival indicator (RAI)
notifies users that a carrier has arrived
by flashing a yellow light and/or by
sounding a chime. Both the light and
chime are turned off by pressing the
reset button on the indicator. The RAI
can be installed adjacent to a station
or in a remote location.
The carrier storage unit provides ample
and convenient storage for Universal
and Eco-Seal™ carriers. The carrier
storage unit stores up to 39 4-inch
carriers or up to 16 6-inch carriers.
A remote personal indicator acts as a
virtual station and has its own system
address. These will light/sound only
when a carrier is directed to the specific address assigned to the indicator.
This allows multiple groups of users to
effectively share a single PTS station.
Remote personal indicators may be
installed adjacent to the station or at
a remote location. Up to six unique
personal indicator addresses may be
assigned to each PTS station.
For More Information in North America:
Swisslog Healthcare Solutions
Email: [email protected]
USA: 800.764.0300
Canada: 877.294-2831 | 905.629.2400
12.375"
(31.5 cm)
13.625"
(34.5 cm)
17"
(43.25 cm)
51.5"
(131 cm)
66.375"
(168.5 cm)
11.75"
(30 cm)
SwisslogHealthcareSolutions
50"
(127 cm)
15.625"
(39.75 cm)
SwisslogNA
WWW.SWISSLOG.COM
©2011 Swisslog CM# PTS-201
Remote Personal Indicators
Indicators can also be configured as
virtual stations called remote personal
indicators.
The carrier storage unit has a carpeted
interior and is installed flush-mounted
into a finished wall - requiring no
additional floor space.
Swisslog’s TransLogic
pneumatic tube
systems transport
carriers using
intricate paths of
galvanized steel
tubing hidden
behind walls and
above the ceilings
in hospitals and
between buildings.
Blower units provide
air pressure and
vacuum to move
the carriers to their
destination, while
transfer units direct
carriers to the
correct tube paths.
Galvanized Steel
Tubing
Pneumatic tube system (PTS)
galvanized steel tubing consists
of straight tubing, bends,
couplings and assorted fittings
used to construct the carrier
distribution network. Tubing and
bends are 16-gauge galvanized
steel, available in 4-inch O.D. and
6-inch O.D.
Bends
Partial bends and 90 degree bends
are used to change the direction
of tubing.
Maximum Specifications
6-inch
4-inch
4.5" (11.43 cm)
3" (7.62 cm)
Carrier Storage Unit
65.62" (166.67 cm)
64.25" (163.20 cm)
Remote Arrival Indicators
50" (127 cm)
50" (127 cm)
70" (177.8 cm)
69.25" (175.90 cm)
6" (15.25 cm)
4" (10.16 cm)
Joint Components
Three types of joints are used
throughout the tubing network:
the expanded-end joint, drive
sleeve and bolted coupling.
The standard joint is a slip socket
type. The tubing expanded-ends
have a patented design that
provides the smoothest possible
transition for a carrier and
minimizes noise and carrier wear.
Cut tubing ends are joined
with either a drive sleeve or a
bolted coupling. Joints at major
components (stations and
transfer units) are usually made
with a bolted coupling.
Tube Hangers
Tube hangers are used to suspend
pneumatic tubing from the
structure. Both tear drop hangers
and strut support hangers mount
to 1-5/8” channel.
5"
12.7 cm
3 1/2"
8.89 cm
2 1/2"
6.35 cm
5"
12.7 cm
3 1/4"
8.26 cm
4" Dia.
10.16 cm
28"
71.12 cm
28"
71.12 cm
6 5/16"
15.88 cm
6"
15.24 cm
Front
Top
6"
15.24 cm
5 5/16" 115 VAC
13.34 cmPower
Conduit
Entrance
7 1/4" / 18.42 cm
30"
76.2 cm
6"
15.24 cm
5 1/4"
13.34 cm
22 1/2"
57.15 cm
Transfer Unit
Right
Side
3 1/4"
8.23 cm
8 1/4"
20.96 cm
Comm Cable
Entrance
9/16" Dia. Holes for Sway Braces (4)
1.27 cm
9/16" Dia. Mounting Holes (4)
Blower Unit
The blower unit provides vacuum and pressure
to
3 1/4"
8.26 cm
move carriers at consistent speeds regardless of
payload or proximity to the blower. The unit consists
28"
71.12 cm for
of a heavy-duty regenerative blower motor rated
continuous duty and a shifter valve mechanism
used
30"
76.2 cm
to connect either vacuum or pressure to the system
piping as required. Blowers are offered in both 4 and
6 inch versions and can also be optionally equipped
with a variable frequency drive (VFD). VFD equipped
models provide software control of the blower speed
enabling transport of sensitive items at slower speeds
and empty carriers at faster speeds.
5"
12.7 cm
3 1/4"
28"
8.26 cm
28"
71.12
cm
6
5/16"
34 1/2"
71.12 cm 3 1/2"
15.88
5" 87.63 cmcm
8.89 cm
12.7 cm 6"
12 1/2"
15.24 cm
31.75 cm
4"
28" 10.16 cm
71.12 cm
Top
7 1/4"
/ 18.42 cm
Top
230/460 VAC Power
30"
Conduit Entrance
76.2 cm
(Enclosed Models Only)
Front
27"
6"
68.58 cm
15.24 cm
Left Side
1"
2.54 cm
5 1/4"
13.34 cm
2 1/2"
6.35 cm
6 5/16"
8 1/2" 15.88 cm
21.59 cm 6"
6"
15.24 cm
15.24 cm
4" Dia.
10.16 cm
5
5/16"
3 9/16"
8.89 13.34
cm cm
5 5/16"
13.34 cm
7 1/4" / 18.42 cm
3 1/4"
8.23 cm
6"
15.24 cm
Screen Box
13 3/16"
33.66 cm
3 1/4"
8.23 cm
3 9/16"
8.89 cm
5"
12.7 cm
22 1/2"
9/16" Dia. Mounting
57.15 cmHoles (4)
2 1/2"
6.35 cm
5"
12.7 cm
Right
Side
8 1/4"
20.96
cm
Starter/VFD
Access Cover
8 1/4"
20.96 cm
Comm Cable
Entrance
2 1/2"
6.35 cm
5"
12.7 cm
5"
The blower unit is an open-frame design and is38.891/2"cm
12.7 cm
suitable for installation in areas such as mechanical
34 1/2"
87.63 cm
12 1/2"
equipment rooms. A sound attenuated model
31.75 cm
4"
completely enclosed in a sheet metal housing with
10.16 cm
Front
Front
sound absorbing lining and equipped with mufflers is
230/460 VAC Power
Conduit Entrance
also available. The sound attenuated version permits
27"
68.58 cm
installation near occupied areas. Both models use
5 1/4"
Left Side 22 1/2"
5 1/4"
13.34 cm
blower motor isolation mounts, insulating vibrations
22 1/2"
57.15 cm
13.34 cm
57.15 cm
1"
2.54
cm
from the structure. To conserve energy, the blower9/16"
is
Dia. Holes for Sway Braces1.27
(4) cm
1.27 cm
automatically turned off during periods of inactivity.
4" Dia.
10.16 cm
4" Dia.
10.16 cm
8 1/2"
21.59 cm
115 VAC
Power
Conduit
Entrance
Right
3 9/16"
Side
8.89 cm
115 VAC
Power
Conduit
Entrance
13 3/16"
33.66 cm
Right
Side
3 9/16"
8.89 cm
Specifications
Drive Mechanism: Electromechanical
Power Requirements:
105 to 125 VAC, 60 Hz, Single Phase, 3A
The entire transfer unit is
enclosed in a rigid metal box
frame with removable side covers
for service. The simple design and
heavy-duty construction provide
very high reliability. Diagnostic
features such as a built-in port
alignment gauge, and diagnostic
switches and indicators on
the control assembly simplify
maintenance. A port cap is used
to cover an unused line from a
transfer unit.
Control Requirements:
4 conductor cable, #22 AWG stranded,
5 VDC maximum open circuit voltage,
200 mA maximum short circuit current
Starter/VFD Access Cover
Comm Cable
(Enclosed Models Only)Entrance
1x4
Comm Cable
Entrance
Environmental Requirements:
Temperature Operating0°
to8 1/2"
120° F (5° to 49° C)
34 1/2"
8 1/2"87.63 cm
21.59 cm
12 1/2" 21.59 cm
Storage
Temperature-20°
to
180° F (29° to 82° C)
Blower Type: Regenerative
12 1/2"
31.75 cm
31.75 cm
3 9/16"
4"
Relative
0 to3 9/16"
90%
8.89 cm
4"
10.16 cm Humidity
8.89 cm
10.16 cm
13 3/16"
Maximum
Operating
RPM
3500
Power Requirements:
13 3/16"
33.66 cm
230/460 VAC Power
33.66 cm
230/460 VAC Power
Conduit Entrance
4-inch6-inch
3
9/16"
Conduit
Entrance
(Enclosed
Models
Only)
Shifter Valve Motor: 105-125 VAC, 60 Hz, 1 Phase, 5.4(Enclosed
A Models Only)27"
3 9/16"
8.89 cm
8.89 cm
27"
68.58 cm frame
Open
240 lbs/109
kg 395 lbs/179 kg
Blower Motor: 200-230, 460 VAC, 50/60 Hz, 3 Phase
68.58 cm
Screen Box
Screen
Box
Open
frame
(w/VFD)
250
lbs/113
kg
405 lbs/184 kg
Horsepower*
200-230 VAC
460 VAC Left Side
Left Side
Sound
Attenuated
375
lbs/170
kg
530 lbs/240 kg
Starter/VFD
Access
Cover
(Enclosed
Models
Only)
4-inch
4.2-4.5
4.5 1"
1"
2.54 cm
2.54 cm
Sound
Attenuated
(w/VFD)
385
lbs/175
kg
540 lbs/245 kg
6-inch
8.7-10
10
Heat
output
(approximately)
9000
BTU/hr
8000 BTU/hr
Full Load Amperage*
Sound
levels
4-inch
12-11 5.5
In open area (open frame) 75 dbA
82 dbA
6-inch
26-23
11.5
In
open
area
(attenuated)
61
dbA
72 dbA
*Size all circuit protection in accordance with local, state, and national
electrical codes.
Mounted above ceiling** 51-55 dbA
61-66 dbA
**Attenuated model only - sound measurement 3 feet below ceiling
4 conductor cable, #22 AWG stranded, 5 VDC maximum open
circuit voltage, 200 mA maximum short circuity current
1x6
System
4-inch
6-inch
Weight
205 lbs
93.0 kg
250 lbs
113.4 kg
1x2
Temperature Operating: 0° to 120° F
(5° to 49° C))
Storage Temperature: -20° to 180° F
(29° to 82° C)
Relative Humidity: 0 to 90%
Max. System Vacuum/Pressure: 4 psig
Positioning Time: Typically 2 sec.
(3 sec. max)
Heat Output: Approx. 130 BTU/hr
Access Cover
Screen Box
34 1/2"
87.63 cm
Max. vacuum/pressure at 5000 ft / 1.5 km: 3.5 psig
Max. output at zero pressure and 500 ft / 152.4 m:
165 SCFM for 4-inch / 330 SCFM for 6-inch
115 VAC
Power
Conduit
Entrance
1.27 cm
3 1/2"
8.89 cm
Specifications
6"
15.24 cm
The transfer unit is a switching
device used at branching points
in the system to direct the path
of a carrier from a single pipe
at one end to any one of two,
four, or six selectable pipes at
the other end. An optical sensor
is contained within each unit to
detect the passage of a carrier. A
moveable tube gently guides the
carrier through the unit in either
direction. The tube is positioned
precisely at the selected port by a
magnetic proximity sensor.
0
1
2
3
Access Cover
F
C E
E
D
B
A
System WeightA B C D E
F
4-inch
145 lbs
50 1/2”44 3/4”18” 18” 6 5/8”13 5/8”
65.7 kg 128.3 cm 113.7 cm 45.7 cm 45.7 cm 16.5 cm
34.9 cm
6-inch
185 lbs
52 7/8”47 1/4”21 1/2”21 1/2”8” 17”
83.9 kg 134.4 cm 120 cm 54.6 cm 54.61 cm 20.3 cm
43.2 cm
6-inch
95 lbs
44”
34 3/4 “18 7/8”18 7/8”8” 13”
Mini
43.1 kg 111.8 cm 88.3 cm
48 cm
48 cm
20.3 cm
33 cm
F
System DWeight
4-inch
145 lbs
G
H 65.7 kg
A
50-1/2"
128.3 cm
B
44-3/4"
113.7 cm
D
AC
17-3/4"
17-3/4"
B
Access
Cover
45.1 cm
45.1 cm
E
6-5/8"
16.5 cm
F
13-5/8"
34.9 cm
6-inch
52-7/8"
134.4 cm
47-1/4"
120.0 cm
21-1/2"
54.6 cm
8"
20.3 cm
17"
43.2 cm
185 lbs
83.9 kg
21-1/2"
54.61 cm
C E I
A B
C
D
E
F
G
H
I
53 3/4”48 3/4”19 3/4”20 11/16”10 11/16”4 5/16”10 5/16”4 5/8”5 5/16”
136.5 cm 123.8 cm
50.2 cm
52.8 cm
27.4 cm
11.4 cm
26.0 cm
11.5 cm
13.9 cm
58 7/8”53 11/16”24 1/2”26 5/8”14 5/8”4 15/16”13 1/8”6 5/16”7 5/8”
149.4 cm 136.5 cm
62.2 cm
67.6 cm
37.2 cm
12.7 cm
33.3 cm
15.9 cm
19.3 cm
System Weight
A
AB
4-inch 205 lbs 53-3/4"
48-3/4"
B cm
93.0 kg 136.5 cm 123.8
6-inch 250 lbs 58-7/8" 53-11/16"
E
113.4 kg 149.4 cm 136.5 cm
SystemWeight A
B
4-inch
125 lbs
43”
38”
56.7 kg 109.2 cm 96.5 cm
6-inch
165 lbs
47”
42”
74.8 kg 119.4 cm 106.7 cm
C
D
E AccessFCover
G
19-1/2" 20-11/16" 10-11/16" 4-5/16" 10 5/16"
49.5 cm 52.8 cm 27.4 cm 11.4 cm 26.0 cm
24-3/8" 26-7/16" 11-1/8" 4-15/16" 13-1/8"
62.2 cm 67.3 cm 28.2 cm 12.7 cm 33.3 cm
H
4-5/8"
11.5 cm
6-5/16"
15.9 cmG
I
5-5/16"
13.9 cm
K
7-1/2"
19.1 cm
C
H
J
F
D
C
D
E
F G
H J
K
18 1/2”
8”
36 1/4”5 5/8”16” 5 1/2”3 3/4”12”
47.0 cm
20.3 cm
92.0 cm
14.0 cm 40.6 cm
14.0 cm 9.5 cm
30.5 cm
23 1/2”10 1/2”40 1/4”7 5/8”21” 8” 4 1/2”15
59.7 cm
26.7 cm
102.2 cm
19.0 cm 53.3 cm
20.3 cm 11.4 cm
38.1 cm
5"
12.7 cm
3 1/2"
8.89 cm
2 1/2"
6.35 cm
5"
12.7 cm
3 1/4"
8.26 cm
4" Dia.
10.16 cm
28"
71.12 cm
28"
71.12 cm
6 5/16"
15.88 cm
6"
15.24 cm
Front
Top
6"
15.24 cm
5 5/16" 115 VAC
13.34 cmPower
Conduit
Entrance
7 1/4" / 18.42 cm
30"
76.2 cm
6"
15.24 cm
5 1/4"
13.34 cm
22 1/2"
57.15 cm
Transfer Unit
Right
Side
3 1/4"
8.23 cm
8 1/4"
20.96 cm
Comm Cable
Entrance
1.27 cm
Blower Unit
The blower unit provides vacuum and pressure
to
3 1/4"
8.26 cm
move carriers at consistent speeds regardless of
payload or proximity to the blower. The unit consists
28"
71.12 cm for
of a heavy-duty regenerative blower motor rated
continuous duty and a shifter valve mechanism
used
30"
76.2 cm
to connect either vacuum or pressure to the system
piping as required. Blowers are offered in both 4 and
6 inch versions and can also be optionally equipped
with a variable frequency drive (VFD). VFD equipped
models provide software control of the blower speed
enabling transport of sensitive items at slower speeds
and empty carriers at faster speeds.
5"
12.7 cm
3 1/4"
28"
8.26 cm
28"
71.12
cm
6
5/16"
34 1/2"
71.12 cm 3 1/2"
15.88
5" 87.63 cmcm
8.89 cm
12.7 cm 6"
12 1/2"
15.24 cm
31.75 cm
4"
28" 10.16 cm
71.12 cm
Top
7 1/4"
/ 18.42 cm
Top
230/460 VAC Power
30"
Conduit Entrance
76.2 cm
Front
27"
6"
68.58 cm
15.24 cm
Left Side
1"
2.54 cm
5 1/4"
13.34 cm
2 1/2"
6.35 cm
6 5/16"
8 1/2" 15.88 cm
21.59 cm 6"
6"
15.24 cm
15.24 cm
4" Dia.
10.16 cm
5
5/16"
3 9/16"
8.89 13.34
cm cm
5 5/16"
13.34 cm
7 1/4" / 18.42 cm
3 1/4"
8.23 cm
6"
15.24 cm
Screen Box
13 3/16"
33.66 cm
3 1/4"
8.23 cm
3 9/16"
8.89 cm
5"
12.7 cm
22 1/2"
9/16" Dia. Mounting
57.15 cmHoles (4)
2 1/2"
6.35 cm
5"
12.7 cm
Right
Side
8 1/4"
20.96
cm
Starter/VFD
Access Cover
8 1/4"
20.96 cm
Comm Cable
Entrance
2 1/2"
6.35 cm
5"
12.7 cm
5"
The blower unit is an open-frame design and is38.891/2"cm
12.7 cm
suitable for installation in areas such as mechanical
34 1/2"
87.63 cm
12 1/2"
equipment rooms. A sound attenuated model
31.75 cm
4"
completely enclosed in a sheet metal housing with
10.16 cm
Front
Front
sound absorbing lining and equipped with mufflers is
230/460 VAC Power
Conduit Entrance
also available. The sound attenuated version permits
27"
68.58 cm
installation near occupied areas. Both models use
5 1/4"
Left Side 22 1/2"
5 1/4"
13.34 cm
blower motor isolation mounts, insulating vibrations
22 1/2"
57.15 cm
13.34 cm
57.15 cm
1"
2.54
cm
from the structure. To conserve energy, the blower9/16"
is
Dia. Holes for Sway Braces1.27
(4) cm
1.27 cm
automatically turned off during periods of inactivity.
4" Dia.
10.16 cm
4" Dia.
10.16 cm
8 1/2"
21.59 cm
115 VAC
Power
Conduit
Entrance
Right
3 9/16"
Side
8.89 cm
115 VAC
Power
Conduit
Entrance
13 3/16"
33.66 cm
Right
Side
3 9/16"
8.89 cm
Specifications
Drive Mechanism: Electromechanical
Power Requirements:
105 to 125 VAC, 60 Hz, Single Phase, 3A
The entire transfer unit is
enclosed in a rigid metal box
frame with removable side covers
for service. The simple design and
heavy-duty construction provide
very high reliability. Diagnostic
features such as a built-in port
alignment gauge, and diagnostic
switches and indicators on
the control assembly simplify
maintenance. A port cap is used
to cover an unused line from a
transfer unit.
4 conductor cable, #22 AWG stranded,
5 VDC maximum open circuit voltage,
200 mA maximum short circuit current
Comm Cable
(Enclosed Models Only)Entrance
1x4
Comm Cable
Entrance
Temperature Operating0°
to8 1/2"
120° F (5° to 49° C)
34 1/2"
8 1/2"87.63 cm
21.59 cm
12 1/2" 21.59 cm
Storage
Temperature-20°
to
180° F (29° to 82° C)
Blower Type: Regenerative
12 1/2"
31.75 cm
31.75 cm
3 9/16"
4"
Relative
0 to3 9/16"
90%
8.89 cm
4"
10.16 cm Humidity
8.89 cm
10.16 cm
13 3/16"
Maximum
Operating
RPM
3500
Power Requirements:
13 3/16"
33.66 cm
230/460 VAC Power
33.66 cm
230/460 VAC Power
Conduit Entrance
4-inch6-inch
3
9/16"
Conduit
Entrance
(Enclosed
Models
Only)
Shifter Valve Motor: 105-125 VAC, 60 Hz, 1 Phase, 5.4(Enclosed
A Models Only)27"
3 9/16"
8.89 cm
8.89 cm
27"
68.58 cm frame
Open
240 lbs/109
kg 395 lbs/179 kg
Blower Motor: 200-230, 460 VAC, 50/60 Hz, 3 Phase
68.58 cm
Screen Box
Screen
Box
Open
frame
(w/VFD)
250
lbs/113
kg
405 lbs/184 kg
Horsepower*
200-230 VAC
460 VAC Left Side
Left Side
Sound
Attenuated
375
lbs/170
kg
530 lbs/240 kg
Starter/VFD
Access
Cover
(Enclosed
Models
Only)
4-inch
4.2-4.5
4.5 1"
1"
2.54 cm
2.54 cm
Sound
Attenuated
(w/VFD)
385
lbs/175
kg
540 lbs/245 kg
6-inch
8.7-10
10
Heat
output
(approximately)
9000
BTU/hr
8000 BTU/hr
Full Load Amperage*
Sound
levels
4-inch
12-11 5.5
In open area (open frame) 75 dbA
82 dbA
6-inch
26-23
11.5
In
open
area
(attenuated)
61
dbA
72 dbA
*Size all circuit protection in accordance with local, state, and national
electrical codes.
Mounted above ceiling** 51-55 dbA
61-66 dbA
**Attenuated model only - sound measurement 3 feet below ceiling
4 conductor cable, #22 AWG stranded, 5 VDC maximum open
circuit voltage, 200 mA maximum short circuity current
1x6
System
4-inch
6-inch
Weight
205 lbs
93.0 kg
250 lbs
113.4 kg
1x2
Temperature Operating: 0° to 120° F
(5° to 49° C))
Storage Temperature: -20° to 180° F
(29° to 82° C)
Relative Humidity: 0 to 90%
Max. System Vacuum/Pressure: 4 psig
Positioning Time: Typically 2 sec.
(3 sec. max)
Heat Output: Approx. 130 BTU/hr
Access Cover
Screen Box
34 1/2"
87.63 cm
Max. vacuum/pressure at 5000 ft / 1.5 km: 3.5 psig
Max. output at zero pressure and 500 ft / 152.4 m:
165 SCFM for 4-inch / 330 SCFM for 6-inch
115 VAC
Power
Conduit
Entrance
1.27 cm
3 1/2"
8.89 cm
Specifications
6"
15.24 cm
The transfer unit is a switching
device used at branching points
in the system to direct the path
of a carrier from a single pipe
at one end to any one of two,
four, or six selectable pipes at
the other end. An optical sensor
is contained within each unit to
detect the passage of a carrier. A
moveable tube gently guides the
carrier through the unit in either
direction. The tube is positioned
precisely at the selected port by a
magnetic proximity sensor.
0
1
2
3
Access Cover
F
C E
E
D
B
A
System WeightA B C D E
F
4-inch
145 lbs
50 1/2”44 3/4”18” 18” 6 5/8”13 5/8”
65.7 kg 128.3 cm 113.7 cm 45.7 cm 45.7 cm 16.5 cm
34.9 cm
6-inch
185 lbs
52 7/8”47 1/4”21 1/2”21 1/2”8” 17”
83.9 kg 134.4 cm 120 cm 54.6 cm 54.61 cm 20.3 cm
43.2 cm
6-inch
95 lbs
44”
34 3/4 “18 7/8”18 7/8”8” 13”
Mini
43.1 kg 111.8 cm 88.3 cm
48 cm
48 cm
20.3 cm
33 cm
F
System DWeight
4-inch
145 lbs
G
H 65.7 kg
A
50-1/2"
128.3 cm
B
44-3/4"
113.7 cm
D
AC
17-3/4"
17-3/4"
B
Access
Cover
45.1 cm
45.1 cm
E
6-5/8"
16.5 cm
F
13-5/8"
34.9 cm
6-inch
52-7/8"
134.4 cm
47-1/4"
120.0 cm
21-1/2"
54.6 cm
8"
20.3 cm
17"
43.2 cm
185 lbs
83.9 kg
21-1/2"
54.61 cm
C E I
A B
C
D
E
F
G
H
I
53 3/4”48 3/4”19 3/4”20 11/16”10 11/16”4 5/16”10 5/16”4 5/8”5 5/16”
136.5 cm 123.8 cm
50.2 cm
52.8 cm
27.4 cm
11.4 cm
26.0 cm
11.5 cm
13.9 cm
58 7/8”53 11/16”24 1/2”26 5/8”14 5/8”4 15/16”13 1/8”6 5/16”7 5/8”
149.4 cm 136.5 cm
62.2 cm
67.6 cm
37.2 cm
12.7 cm
33.3 cm
15.9 cm
19.3 cm
System Weight
A
AB
4-inch 205 lbs 53-3/4"
48-3/4"
B cm
93.0 kg 136.5 cm 123.8
6-inch 250 lbs 58-7/8" 53-11/16"
E
113.4 kg 149.4 cm 136.5 cm
SystemWeight A
B
4-inch
125 lbs
43”
38”
56.7 kg 109.2 cm 96.5 cm
6-inch
165 lbs
47”
42”
74.8 kg 119.4 cm 106.7 cm
C
D
E AccessFCover
G
19-1/2" 20-11/16" 10-11/16" 4-5/16" 10 5/16"
49.5 cm 52.8 cm 27.4 cm 11.4 cm 26.0 cm
24-3/8" 26-7/16" 11-1/8" 4-15/16" 13-1/8"
62.2 cm 67.3 cm 28.2 cm 12.7 cm 33.3 cm
H
4-5/8"
11.5 cm
6-5/16"
15.9 cmG
I
5-5/16"
13.9 cm
K
7-1/2"
19.1 cm
C
H
J
F
D
C
D
E
F G
H J
K
18 1/2”
8”
36 1/4”5 5/8”16” 5 1/2”3 3/4”12”
47.0 cm
20.3 cm
92.0 cm
14.0 cm 40.6 cm
14.0 cm 9.5 cm
30.5 cm
23 1/2”10 1/2”40 1/4”7 5/8”21” 8” 4 1/2”15
59.7 cm
26.7 cm
102.2 cm
19.0 cm 53.3 cm
20.3 cm 11.4 cm
38.1 cm
Pneumatic Tube
System Accessories
SWISSLOG
SPECIFICATIONS
TRANSMISSION
COMPONENTS FOR
TRANSLOGIC
PNEUMATIC TUBE
SYSTEMS
The remote arrival indicator (RAI)
notifies users that a carrier has arrived
by flashing a yellow light and/or by
sounding a chime. Both the light and
chime are turned off by pressing the
reset button on the indicator. The RAI
can be installed adjacent to a station
or in a remote location.
The carrier storage unit provides ample
and convenient storage for Universal
and Eco-Seal™ carriers. The carrier
storage unit stores up to 39 4-inch
carriers or up to 16 6-inch carriers.
A remote personal indicator acts as a
virtual station and has its own system
address. These will light/sound only
when a carrier is directed to the specific address assigned to the indicator.
This allows multiple groups of users to
effectively share a single PTS station.
Remote personal indicators may be
installed adjacent to the station or at
a remote location. Up to six unique
personal indicator addresses may be
assigned to each PTS station.
For More Information in North America:
Swisslog Healthcare Solutions
Email: [email protected]
USA: 800.764.0300
Canada: 877.294-2831 | 905.629.2400
12.375"
(31.5 cm)
13.625"
(34.5 cm)
17"
(43.25 cm)
51.5"
(131 cm)
66.375"
(168.5 cm)
11.75"
(30 cm)
SwisslogHealthcareSolutions
50"
(127 cm)
15.625"
(39.75 cm)
SwisslogNA
WWW.SWISSLOG.COM
©2011 Swisslog CM# PTS-201
Remote Personal Indicators
Indicators can also be configured as
virtual stations called remote personal
indicators.
The carrier storage unit has a carpeted
interior and is installed flush-mounted
into a finished wall - requiring no
additional floor space.
Swisslog’s TransLogic
pneumatic tube
systems transport
carriers using
intricate paths of
galvanized steel
tubing hidden
behind walls and
above the ceilings
in hospitals and
between buildings.
Blower units provide
air pressure and
vacuum to move
the carriers to their
destination, while
transfer units direct
carriers to the
correct tube paths.
Galvanized Steel
Tubing
Pneumatic tube system (PTS)
galvanized steel tubing consists
of straight tubing, bends,
couplings and assorted fittings
used to construct the carrier
distribution network. Tubing and
bends are 16-gauge galvanized
steel, available in 4-inch O.D. and
6-inch O.D.
Bends
Partial bends and 90 degree bends
are used to change the direction
of tubing.
Maximum Specifications
6-inch
4-inch
4.5" (11.43 cm)
3" (7.62 cm)
Carrier Storage Unit
65.62" (166.67 cm)
64.25" (163.20 cm)
Remote Arrival Indicators
50" (127 cm)
50" (127 cm)
70" (177.8 cm)
69.25" (175.90 cm)
6" (15.25 cm)
4" (10.16 cm)
Joint Components
Three types of joints are used
throughout the tubing network:
the expanded-end joint, drive
sleeve and bolted coupling.
The standard joint is a slip socket
type. The tubing expanded-ends
have a patented design that
provides the smoothest possible
transition for a carrier and
minimizes noise and carrier wear.
Cut tubing ends are joined
with either a drive sleeve or a
bolted coupling. Joints at major
components (stations and
transfer units) are usually made
with a bolted coupling.
Tube Hangers
Tube hangers are used to suspend
pneumatic tubing from the
structure. Both tear drop hangers
and strut support hangers mount
to 13/16” channel.

Swisslog`s TransLogic pneumatic tube systems transport carriers

Transcription

Similar documents