CDX-R3000/RW300

Transcription

CDX-R3000/RW300

CDX-R3000/RW300
SERVICE MANUAL
US Model
CDX-R3000/RW300
Ver. 1.1 2005.07
Canadian Model
E Model
CDX-R3000
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
NEW
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD Drive Mechanism Type
MG-611XA-186//K
Optical Pick-up Name
KSS1000E
SPECIFICATIONS
CD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
120 dB
10 – 20,000 Hz
Below measurable limit
Tuner section
FM
Tuning range
US, Canadian Model:
87.5 – 107.9 MHz
E model:
FM tuning interval:
50 kHz/200 kHz
switchable
87.5 – 108 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM
Tuning range
US, Canadian Model:
530 – 1,710 kHz
E Model:
AM tuning interval:
9 kHz/10 kHz switchable
531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Inputs
Tone controls
Audio outputs terminal (rear/sub switchable)
Power antenna relay control terminal
Power amplifier control terminal
Antenna input terminal
Remote controller input terminal (E Model)
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
– Continued on next page –
FM/AM COMPACT DISC PLAYER
9-961-386-02
Sony Corporation
2005G04-1
© 2005.07
e Vehicle Group
Published by Sony Engineering Corporation
1
CDX-R3000/RW300
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Approx. 182 × 53 × 161 mm
(7 1/4 × 2 1/8 × 6 3/8 in.) (w/h/d)
Approx. 1.2 kg
(2 lb. 10 oz.)
Parts for installation and connections (1 set)
Front panel case (1)
Design and specifications are subject to change without
notice.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
optical pick-up
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
semi-fixed resistor
• E model
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
This label is located on the bottom of the chassis.
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
SAFETY-RELATED COMPONENT WARNING!!
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
CDX-R3000/RW300
Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable
CDs)
This unit can play the following discs:
Type of discs
Label on the disc
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Audio CD
MP3 files
• Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
• You cannot play a CD-R/CD-RW that is not finalized∗.
• You can play MP3 files recorded on CD-ROMs, CD-Rs, and
CD-RWs.
• A CD-R/CD-RW to which a session can be added can be played.
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
∗ A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CN751) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CN751
J-2502-076-1
SERVO BOARD
CN1
3
CDX-R3000/RW300
TABLE OF CONTENTS
1. GENERAL
Location of Controls (US, Canadian Model) .......................... 5
Location of Controls (E Model) .............................................. 5
Connections (US, Canadian Model) ........................................ 6
Connections (E Model) ........................................................... 7
2. DISASSEMBLY
2-1. Sub Panel (1) Assy .............................................................. 9
2-2. CD Mechanism Block ......................................................... 9
2-3. Main Board ....................................................................... 10
2-4. Chassis (T) Sub Assy ........................................................ 10
2-5. Roller Arm Assy ................................................................ 11
2-6. Chassis (OP) Assy ............................................................. 11
2-7. Optical Pick-up ................................................................. 12
2-8. SL Motor Assy (M902) ..................................................... 12
2-9. LE Motor Assy (M903) ..................................................... 13
2-10. Servo Board ....................................................................... 13
3. DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
IC Pin Descriptions ........................................................... 14
Block Diagram –CD Section– ........................................... 18
Block Diagram –Main Section– ........................................ 19
Block Diagram –Display Section– .................................... 20
Circuit Boards Location .................................................... 20
Note for Printed Wiring Boards and
Schematic Diagrams .......................................................... 21
3-7. Waveforms ......................................................................... 21
3-8. Printed Wiring Boards –CD Mechanism Section– ............ 22
3-9. Schematic Diagram –CD Mechanism Section– ................ 23
3-10. Schematic Diagram –Main Section (1/2)– ........................ 24
3-11. Schematic Diagram –Main Section (2/2)– ........................ 25
3-12. Printed Wiring Boards –Main Section– ............................ 26
3-13. Printed Wiring Board –Display Section– .......................... 27
3-14. Schematic Diagram –Display Section– ............................. 28
3-15. IC Block Diagrams ............................................................ 29
4. EXPLODED VIEWS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
Main Section ..................................................................... 31
Front Panel Section ........................................................... 32
CD Mechanism Section (1) ............................................... 33
5. ELECTRICAL PARTS LIST ........................................ 37
4
CDX-R3000/RW300
SECTION 1
GENERAL
(US, Canadian Model)
This section is extracted
from instruction manual.
(E Model)
5
CDX-R3000/RW300
Connections (US, Canadian Model)
6
CDX-R3000/RW300
Connections (E Model)
7
CDX-R3000/RW300
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1.
SUB PANEL (1) ASSY
(Page 9)
2-2.
CD MECHANISM BLOCK
(Page 9)
2-3.
MAIN BOARD
(Page 10)
2-7.
8
2-4.
CHASSIS (T) SUB ASSY
(Page 10)
2-5.
ROLLER ARM ASSY
(Page 11)
2-10. SERVO BOARD
(Page 13)
2-6.
CHASSIS (OP) ASSY
(Page 11)
2-8.
SL MOTOR ASSY (M902)
(Page 12)
OPTICAL PICK-UP
(Page 12)
2-9.
LE MOTOR ASSY (M903)
(Page 13)
CDX-R3000/RW300
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (1) ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 x 6)
4 sub panel (1) assy
2-2. CD MECHANISM BLOCK
7 bracket (CD)
5 CD mechanism block
6 two screws
(+PTT 2.6 x 6)
2 screw
(+PTT 2.6 x 6)
3
1 screw
(+PTT 2.6 x 6)
4 CN751
9
CDX-R3000/RW300
2-3. MAIN BOARD
1 three screws
(+BTT)
2 two screws
(+PTT 2.6 x 8)
3 MAIN board
2-4. CHASSIS (T) SUB ASSY
4 claw
2 two screws
(+P 1.7 x 2.2)
1 two screws
(+P 1.7 x 2.2)
6 chassis (T) sub assy
5 SENSOR board
3 claw
10
CDX-R3000/RW300
2-5. ROLLER ARM ASSY
3 washer (1.0 – 2.5)
5 roller arm assy
4 worm wheel (RA)
2 spring (RAR)
1 spring (RAL)
2-6. CHASSIS (OP) ASSY
8
qa chassis (OP) assy
0 compression spring (damper)
lever (D)
4 washer
1 CN2
6
9 two compression springs (damper)
5 gear (LE1)
7
slider (R)
3 tennsion coil spring (KF)
2 Remove the six solderings.
11
CDX-R3000/RW300
2-7. OPTICAL PICK-UP
2 chucking arm sub assy
5 claw
1 tension coil spring (CHKG)
7 optical pick-up
6 main shaft
4 rack (SL)
3 screw
(+B 1.4 x 5)
2-8. SL MOTOR ASSY (M902)
1 screw
(+P 1.4 x 1.8)
2 SL motor assy (M902)
12
CDX-R3000/RW300
2-9. LE MOTOR ASSY (M903)
8 screw
(+M 1.7 x 2.5)
0 woam (LEB) assy
9 bearing (LEB)
qf two toothed lock screws
(+M 1.4 )
2 washer
qa screw
(+M 1.7 x 2.5)
3 gear (LE1)
lever (D)
4
bracket (LEM)
qs screw
(+M 1.7 x 2.5)
qd
qg LE motor assy
(M903)
5
6 screw
(+P 1.7 x 2.2)
slider (R)
7 leaf spring (LE)
1 Remove the soldering.
2-10. SERVO BOARD
1 Remove the eight solderings.
6 SERVO board
2 Remove the three solderings.
4 toothed lock screw
(M 1.7)
5 claw
3 CN2
13
CDX-R3000/RW300
SECTION 3
DIAGRAMS
3-1. IC PIN DESCRIPTIONS
• IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)
Pin No.
Pin Name
I/O
Pin Description
1
LD
O
Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON)
14
2
3
PD
PN
I
I
Dimmer monitor input from optical pick-up laser diode.
Not used. (Fixed at L in this set)
4
5
AVDD
DGND
—
—
Analog power supply pin (+3.3 V)
Ground
6
7
RFOK
INTQ
O
O
RFOK signal output to system control IC.
CD text pack synchronization signal output to system control IC.
8
RST
I
9
A0
I
CD reset signal input from system control IC.
Command/parameter discrimination signal input from system control IC.
10
STB
I
(L: command transmission, H: parameter transmission)
Data strobe signal input from system control IC.
11
12
SCK
SO
I
O
Serial clock input from system control IC.
Serial data output to system control IC.
13
14
SI
DVDD
I
—
Serial data input from system control IC.
Power supply pin (+3.3 V)
15
16
DAVDD
ROUT
—
O
D/A converter power supply (+) pin (+3.3 V)
Analog audio signal output (R-ch)
17
18
DAGND
REGC
—
—
Ground
Capacitor connection pin for SCF regulator.
19
20
DAGND
LOUT
—
O
Ground
Analog audio signal output (L-ch)
21
22
23
DAVDD
XVDD
XTAL
—
—
O
D/A converter power supply (+) pin (+3.3 V)
Main system clock output (16.9344 MHz)
24
25
XTAL
XGND
I
—
Main system clock input (16.9344 MHz)
Ground
26
27
DVDD
C1D1/FZD
—
O
Not used. (Open)
28
29
C1D2/TZD
C2D1/RMUTE
O
O
Not used. (Open)
CD R-ch data zero detection signal output
30
31
C2D2/LMUTE
C2D3/SHOCK/SBSY
O
O
CD L-ch data zero detection signal output
Not used. (Open)
32
33
LOCK/FR
WFCK/MIRR
O
O
Not used. (Open)
Not used. (Open)
34
35
RFCK/HOLD
PLCK
O
O
Not used. (Open)
Not used. (Open)
36
37
C16M
DGND
O
—
Not used. (Open)
Ground
38
39
TX
EMPH/RAMOVER
O
O
Not used. (Open)
Not used. (Open)
40
41
FLAG
DVDD
O
—
Not used. (Open)
42
LIMIT
I
43
XTALEN
I
44
DGND
—
(Fixed at L in this set)
Ground
45
46
DIN
DOUT
I
O
Not used. (Connect to DOUT in this set)
Not used. (Connect to DIN in this set)
47
48
SCKIN
SCKO
I
O
Not used. (Connect to SCKO in this set)
Not used. (Connect to SCKIN in this set)
49
LRCKIN
I
Not used. (Connect to LRCK in this set)
Oscillation circuit ON/OFF control signal input (L: ON, H: OFF)
CDX-R3000/RW300
Pin No.
50
Pin Name
LRCK
I/O
O
Pin Description
Not used. (Connect to LRCKIN in this set)
51
52
DVDD
FD+
—
O
Focus servo drive PWM signal output (+)
53
54
FD–
TD+
O
O
Focus servo drive PWM signal output (–)
Tracking servo drive PWM signal output (+)
55
56
TD–
SD+
O
O
Tracking servo drive PWM signal output (–)
Sled servo drive PWM signal output (+)
57
58
SD–
MD+
O
O
Sled servo drive PWM signal output (–)
Spindle servo drive PWM signal output (+)
59
60
MD–
DGND
O
—
Spindle servo drive PWM signal output (–)
Ground
61
62 to 66
TESTEN
TEST4 to TEST0
I
I
67
68
ADGND
EFM
—
O
A/D converter power supply (–) pin
EFM signal output
69
70
ASY
ADVDD
I
—
EFM comparator reference voltage input
A/D converter power supply pin (+3.3 V)
71
72
RFI
EQ2
I
—
RF signal input for EFM data growing.
Not used. (Open)
73
74
EQ1
RF–
—
I
RF amplifier equalizer parts connection pin
Not used. (Open)
75
76
RF2–
AGCO
I
O
RF amplifier inversion input
RF signal output after on AGC.
77
78
79
AGCI
RFO
ATEST
I
O
I
RF AGC signal amplifier input
RF signal output before on AGC.
Not used. (Open)
80
81
C3T
AGND
—
—
Capacitor connection pin for 3T detection.
Ground
82
83
A
C
I
I
Signal input (A) from optical pick-up detector.
Signal input (C) from optical pick-up detector.
84
85
B
D
I
I
Signal input (B) from optical pick-up detector.
Signal input (D) from optical pick-up detector.
86
87
F
E
I
I
Signal input (F) from optical pick-up detector.
Signal input (E) from optical pick-up detector.
88
89
VREFIN
AVDD
I
—
Reference voltage (+1.65 V) input
Analog power supply pin (+3.3 V)
90
91
REFOUT
REFC
O
—
Reference voltage (+1.65 V) output
Capacitor connection pin for reference voltage output.
92
93
FE–
FEO
I
O
Focus error signal amplifier inversion input
Focus error signal amplifier output
94
95
ADCIN
TE-
I
I
Not used. (Open)
Tracking error signal amplifier inversion input
96
97
TEO
TE2
O
O
Tracking error signal amplifier before output
Tracking error signal amplifier after output
98
99
TEC
AGND
I
—
Tracking error signal comparator input
Ground
100
PWMSW
I
Test setting input (Fixed at L in this set)
Test setting input (Fixed at L in this set)
15
CDX-R3000/RW300
• IC801 MB90473PF-G166-BNDE1 (SYSTEM CONTROL) (MAIN BOARD (2/2))
Pin No.
Pin Name
I/O
Pin Description
1
ATT
O
Audio mute control signal output
2 to 4
5
NC
BEEP
—
O
Not used in this set. (Open)
Beep signal output to power amp IC
6
7 to 10
VOL ATT
NC
O
—
Electrical volume ATT control output
11
12 to 14
VSS
NC
—
—
Ground pin
15
16, 17
TU ATT
NC
O
—
Tuner mute control output
18
19
CD SI
CD SO
I
O
CD servo serial data signal input
CD servo serial data signal output
20
21
CD SCK
RE 0
O
O
CD servo serial clock signal output
22
23
RE 1
VCC+3.3
O
—
24
25
EEP SIO
EEP SCK
I/O
O
Serial data signal input/output for EEPROM comunication
Serial clock signal output for EEPROM comunication
26
SHUT SW
I
Shutter switch open/close detect signal input
“L”: Panel open, “H”: Panel close
27
28
LCD CE
LCD SO
O
O
Chip enable signal output to LCD driver IC
Serial data signal output to LCD driver IC Flash: UART serial out
29
30
LCD SCK
NC
O
—
Serial clock signal output to LCD driver IC
31
32
33
STB
AUX
IIC SCK
O
—
O
Standby signal output to power amp IC
IIC bus serial clock signal output
34
35
IIC SIO
VCC+3.3
I/O
—
IIC bus serial data signal input/output
Power supply pin (+3.3 V) (for A/D converter)
36
37
AVRH+3.3
AVSS
—
—
External reference power supply (+3.3 V) (for A/D converter)
Ground pin (for A/D converter)
38, 39
40
KEY IN0, 1
NC
I
—
Key signal input
41
42
RC IN0
VSS
I
—
Rotary commander key signal input
Ground pin
43, 44
45
NC
VSM
—
I
Not used in this set. (Fixed at “L”.)
S meter voltage detect signal input
46
47
DST SEL
KEY ACK
I
I
48
49, 50
NC
MD0, 1
—
I
Input for operation mode designation (Fixed at “H”.)
51
52
MD2
NC
I
—
Input for operation mode designation (Fixed at “L”.)
53
54
BU IN
OP REQ/INTQ
I
O
Back up power supply detect signal input
OP REQ/INTQ select signal output
55
56
CD SELFSW
DIAG
I
I
CD mechanism self load position detect switch signal input
Condition input from power amp IC
57
58
TU ATT IN
UNI SI
I
I
Tuner ATT signal input Not used in this set. (Open)
Serial data signal input Not used in this set. (Open)
59
60
UNI SO
UNI SCK
O
O
Serial data signal output Not used in this set. (Open)
Serial clock signal output Not used in this set. (Open)
61
62
BUS ON
SYS RST
O
O
Bus on signal output
System reset signal output
16
Destination select pin
Key acknowledge detect signal input
CDX-R3000/RW300
Pin No.
63
Pin Name
TEL ATT
I/O
O
Pin Description
TEL ATT signal output Not used in this set. (Open)
64
65
ACC IN
SIRCS
I
I
Accessory power supply detect signal input
Remote control signal (infrared rays) input
66
67
RAM BU
TEST IN
O
I
Not used in this set. (Fixed at “L”.)
Test mode detect signal input
68
FLASH W
I
Memory mode changeover signal input
Normally “H” input (single chip mode)
69
70, 71
NOSE SW
NC
O
—
72
DOOR SW
I
Front panel open/close detect signal input
“L” input: Panel close, “H” input: Panel open
73
74
DOOR IND
RC IN1
O
I
Rotary commander shift key signal input
75
76
XKEY ON
NC
O
—
Key power supply control signal output
77
78
RESET
NC
I
—
Reset signal input
79
80
X1A
X0A
—
—
Oscillator connect pin (32 kHz)
Oscillator connect pin (32 kHz)
81
82
VSS
X0
—
—
Ground pin
Oscillator connect pin (3.68 MHz)
83
84
X1
VCC+3.3
—
—
Oscillator connect pin (3.68 MHz)
85 to 88
89
90
NC
ZERO DET R
ZERO DET L
—
I
I
Mechanism deck mute zero closs detect signal input R
Mechanism deck mute zero closs detect signal input L
91
92
CD STB
CD IN SW
O
I
CD servo data strob signal output Timing of data latch: “L” output
CD mechanism IN-SW detect signal input
93
94
CD LOAD
CD ON/EJECT
O
O
CD mechanism loading motor control signal output
CD mechanism eject motor control signal output
95
96
CDM ON/D SW
CD LIMIT
I
I
CD mechanism DSW detect signal input
CD mechanism IN-LIMIT SW signal input
97
98
RFOK
CD XRST
I
O
CD servo RFOK signal input
CD servo reset signal output
99
CD A0
O
CD servo command/parameter identification signal output
Command transmission: “L” output, parameter transmission: “H” output
100
NC
—
“L” after reset: Flash write mode
Not used in this set. (Fixed at “H”.)
Pin rj (KEY ACK) active: “L” output
17
17
CDX-R3000/RW300
3-2. BLOCK DIAGRAM — CD SECTION —
• R-ch is omitted due to same as L-ch.
• Siganal Path
: CD PLAY
DETECTOR
PD1
PD1
PD2
82 A
PD2
77 AGCI
RFO 78
AGCO 76
71 RFI
EFM 68
69 ASY
ROUT 16
84 B
CD-L
LOUT 20
I-V AMP
RF AMP,DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
IC1
E
E
F
F
87 E
FEO 93
92 FE–
86 F
TEO 96
95 TE–
TE2 97
LD
AUTOMATIC
POWER
CONTROL
Q1
1 LD
89 ZERO DET R
18 CD_SI
19 CD_SO
20 CD_SCK
RFOK 6
INTQ 7
STB 10
A0 9
RST 8
PD 2
PD
97
54
91
99
98
RF_OK
OP INTQ
CD_STB
CD_A0
CD XRST
SYSTEM CONTROL
IC801 (1/3)
OPTICAL
PICK-UP BLOCK
(KSS-1000E)
2-AXIS DEVICE
90 ZERO DET L
SO 12
SI 13
SCK 11
LD
PD
LMUTE 30
RMUTE 29
98 TEC
LASER DIODE
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING
MOTOR DRIVE
IC2
XTAL 23
FCS+
FCS–
11 VO2–
OPIN2+ 5
52 FD+
12 VO2+
OPIN2– 6
53 FD–
13 VO1–
OPIN1+ 2
54 TD+
14 VO1+
OPIN1– 3
55 TD–
X1
16.934MHz
XTAL 24
(FOCUS)
(TRACKING)
TRK+
TRK–
SW1
(DOWN)
SW2
(SELF)
M902
(SLED)
M
M901
(SPINDLE)
M
M903
(LOADING)
M
95 CD_DSW
55 CD_SELFSW
15 VO4+
OPIN4+ 27
56 SD+
16 VO4–
OPIN4– 26
57 SD–
SW3
(DISC IN)
92 CD_INSW
SW4
(LIMIT)
96 CD_LIMIT
17 VO3+
OPIN3+ 24
58 MD+
18 VO3–
OPIN3– 23
59 MD–
10 VOL+
FWD 1
93 CD LOAD
9 VOL–
REV 28
94 CD ON/EJECT
18
18
MAIN
SECTION
(Page 19)
R-CH
83 C
85 D
A
CDX-R3000/RW300
3-3. BLOCK DIAGRAM — MAIN SECTION —
ELECTRONIC VOLUME
IC401
CD
SECTION
A
CD-L
R-CH
(Page 18)
9 C2
8 C1
PJ401
OUTS1 17
OUTS2 18
L
R-CH
1 ANT
R
L 4
R 3
POWER AMP
IC100
7 B2
6 B1
OUTF2 23
12 INRR(FL)
OUTR2 22
OUTF1 25
OUTR1 24
VCC 10
TU VDD 11
E2P VDD 15
TU-SCL 13
TU-SDA 14
REAR
AUDIO OUT
MUTE
Q407
TUX601
(TUNER UNIT)
PJ601
(ANTENNA)
R-CH
11 INRF(RL)
R-CH (FRONT)
R-CH (REAR)
MUTE
Q405
CNP901
1
FL+
9
FL-
PR+ 5
PR- 3
2
RF+ 9
RF- 7
MUTE
Q404
10
MUTE 29
AU+8V
TU+5V
U COM+3.3V
SCL 30
SDA 31
SCL
SDA
MUTE CONTROL
Q400,401
D400
R-CH
IIC SCK 33
IIC SIO 34
45 VSM
15 TU ATT
E2P SCL 16
E2P SDA 17
25 EEP SCK
24 EEP SIO
5
AMP-REM
6
ANT-REM
SW1 29
SW2 27
SYSTEM CONTROL
IC801 (2/3)
S-METER 6
TU MUTE 7
4
FR+
12
FR3
RR+
11
RR-
BATT
SCL
SDA
F900
SDA
SCL
SCL
SDA
2 SDA
4 SCL
RL+
RL-
BATT
16
VOL ATT 6
ATT
BEEP
STB
DIAG
1
5
31
56
16 ACGND
22 STB
25 DIAG
BATT
REG1
REG2
REG3
REG4
REG5
30
37
31
33
34
AU+8V
U-COM+3.3V
SERVO+3.3V
MECHA+6V
DISP+B
35 VP
ACC CHECK
Q900
ACC IN 64
15
TEST IN 67
BU IN 53
7
BATTERY CHECK
Q902,906,907
D912
BATT
TU+5V
TU+5V REG
Q601
• R-CH is omitted due to same as L-CH.
• Signal Path
: CD PLAY
: FM
: AM
19
19
AU+8V
ACC
TEST
CDX-R3000/RW300
3-4. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL
IC801 (3/3)
3-5. CIRCUIT BOARDS LOCATION
LCD DRIVER
IC501
SERVO board
SENSOR board
38 KEYIN0
KEY MATRIX
S501-522
39 KEYIN1
D801
KEY
ACKNOWLEDGE
SWITCH
Q800
SPEAKER board
LCD SO 28
LCD SCK 29
LCD CE 27
64 DI
CLK
63 CL
62 CE
LCD501
SEG3 3
|
|
SEG50 50
LIQUID
CRYSTAL
DISPLAY
PANEL
COM4 51
|
|
COM1 54
47 KEY ACK
DIMMER 1
75 XKEY ON
DISP+B
D810
E model
LED503
(DISC IND)
74 RCIN1
41 RCIN0
CNP900
(REMOTE IN)
(
D521
DISPLAY board
DISP+B
E model
(
S800
FREQUENCY
SELECT
46 DST SEL
9K
) 10K
2 IN
+3.3V REG
IC906
REMOTE CONTROL
SIGNAL RECEIVER
IC502
RESET
IC802
U COM+3.3V
tuner unit
(TUX601)
)
DIMMER
CONTROL
Q501,502
SHUT SW 26
D820
S823
(SHUTTER)
LED501,502
LCD
BACK LIGHT
US,Canadian
model
77 RESET
OUT 1
SIRCS 65
S802
RESET
X801
32.768kHz
3 V OUT
1
VCC
79 X1A
80 X0A
X0 82
X1 83
2 OUT
VDD 2
CE 4
LED504,-518,
520-522,
524,525
DISP+B
IR
X800
3.68MHz
20
20
MAIN board
CDX-R3000/RW300
3-6. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
3-7. WAVEFORMS
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
— Servo Board —
1
For schematic diagrams.
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
: internal component.
•
• C : panel designation.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
: Through hole.
•
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
•
•
•
•
•
•
•
•
•
•
•
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
CD mechanism section
no mark : CD PLAY
Main (1/2), (2/2) and Display sections
no mark : FM
(
) : AM
<
> : CD PLAY
∗
: Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Waveforms are taken with a oscilloscope.
Circled numbers refer to waveforms.
Signal path.
J : CD PLAY
F : FM
f : AM
Abbreviation
CND : Canadian model.
— Main Board —
(MODE: CD PLAY)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
1
1.2Vp-p
16.9344MHz
IC1
wd
32.768kHz
(XTAL)
IC801
2
i;
(X0A)
2
2.4Vp-p
1.6Vp-p
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
3.68MHz
IC1
uj
IC801
(AGCI)
3
C
Q
1.7Vp-p
0V
These are omitted
Approx. 620mVp-p
B E
IC1
od
(FEO)
4
0V
BE C
These are omitted
Approx. 200mVp-p
IC1
ECB
These are omitted
• Abbreviation
21
21
oh
(TEO)
is
(X0)
CDX-R3000/RW300
3-8. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 20 for Circuit Boards Location.
2
1
3
4
5
6
7
: Uses unleaded solder.
8
9
10
11
12
13
14
A
C11
C1
C32
C2
C29
C31
JR90
R45
C7
C30
X1
JR91
B
R44
R42 C5
R41
C8
C3
C6
C28
C13
R11
C38
R13
C36
R1
C27
R14
CN1
(Page 26)
2
C34
C79
R85
R84
C71 C70
C74
C73
IC2
R82
R80
R81
R78
R79
C72
R75
SW3
R83
C76 C77 C78
F
C75
R77
R76
R74
R73 R71
E
R72
R70
FB1
R9
C19
C18
CN
D
R12
C35
R15
C39
C37
C25
C23
C17
JR41
R6
R7
C20
C21
Q1
C26
JR40
C
IC1
SW2
SW1
1-688-822-
G
22
22
CDX-R3000/RW300
• Refer to page 21 for Waveforms.
3-9. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 29 for IC Block Diagram.
C20
R9
C25
Q1
R13
TP32
C23
R7
C21
C19
TP19
CN2
C18
C17
R6
TP33
R14 R15
C36
TP31
C38
TP20
C37
TP30
TP29
TP14 R12
C26
C39
TP21
C35
C27
TP28
TP27
C34
R1
TP26
TP13
TP12
R11
IC1
C28
TP11
TP22
C29
C13
TP10
TP9
TP23
TP8
TP7
C30
TP24
TP6
TP5
TP4
TP25
C31
TP3
SW4
TP2
TP81
TP80
C32
TP1
CN1
C11
JR90
JR91
TP65
TP64
M901
TP85
TP83
TP84
M902
C1
TP82
C5
C3
R45
R44
X1
C8
C6
TP28
TP88
TP29
TP89
SW3
TP58
TP57
TP54
TP48
C7
TP87
TP61
TP60
TP59
TP56
TP55
FB1
C2
TP27
TP63
TP62
R41
JR41
JR40
TP52
TP51
TP53
R42
TP49
TP50
SW2
TP47
TP46
TP45
TP44
SW1
TP43
TP42
TP41
TP90
TP91
TP40
IC B/D
IC2
C79
R85
R84
C78
R83
R82
C72
C77
R81 R80
C73
C76
R79 R78
R70
R71
C70
R72
R73
C71
R74
R75
R76
R77
TP100
C74
TP75
M903
TP92
TP93
TP74
TP71
TP70
TP73
TP72
C75
23
23
(Page 25)
CDX-R3000/RW300
3-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 30 for IC Block Diagram.
TUX601
R607
R608
R604
R606
R603
C600
PJ601
PJ401
C435
C436
JR10
C303
C108
IC100
IC B/D
C424 R416
C113
C440 R431
R421
IC401
Q405
R401
JR103
R400
R409
C425 R414
C408
C411
R407
D921
C444 R432
C438 R429
R419
R406
R405
C410
D909
D917
D916
C409
C107
R420
R415
D907
D908
C426
D905
D906
R412
R411
D904
C414
D903
D902
C101
Q404
Q403
D922
Q402
R404
C400
R418
C428
R417 JR6
R435
C437 R427
R436
C452
C453
R440
R442
R441
CNP901
L400
R443
C416
Q601
C417
C451
C450
Q406
Q407
C106
L602
Q401
R615
C618
C619
D400
C620
D600
Q400
C111
R931
R424
C109
C430
R932
R913
D914
F900
L900
C922
Q900
R903
R902
(Page 25)
24
24
C908
R904
D919
CDX-R3000/RW300
3-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 21 for Waveforms.
(Page 24)
R813
C447
R822
R841
R839
R840
R828
R823
R862
D820
R830
R821
R861
R447
C802
D702
C441
C446
R837
C809
C801
C810
R448
CN751
C709
C707
R834
R832
C823
R865
C824
R708
R819
R709
R805
R864
R707
R818
R838
R806
C813
R705
C821
R703
R846
R801
JR11
R847
R804
C705
R850
IC801
R810
L702
(Page 23)
C701
R815
R826
C807
R811
L701
C822
L700
C704
R722
C825
JR5
R800
S800
C820
R936
R808
C818
R853
R809
X800
R843
R802
R851
IC802
R854
X801
C816
R849
D810
R852
JW138
R873
R835
CNP800
C817 R845
C812
R860
R848
D801
R844
R925
(Page 28)
R833
R901
R814
Q800
R927
D808
R437
C815
D813
D812
R824
Q906
R928
R914
Q907
C706
25
25
R912
D912
D915
R915
CNP900
R917
C909
D811
D816
D814
D817
D815
R825
S802
Q902
CDX-R3000/RW300
3-12. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 20 for Circuit Boards Location.
2
1
3
4
5
6
7
8
9
10
11
12
13
14
15
PJ401
A
PJ601
CNP900
R427
IC100
C437
R914
JW110
JW111
R418
R421
D903
C113
R443
C108
D902
JW113
R442
B
JW112
CNP901
C436 C435
C303
JW108
JW109
JW126
JW127
JR6
JW97
R931
D909
JW96
D914
JW95
D922
Q403
C101
R805
R917
R912
R928
Q902
JW86
C704
R824
R810
C908
R902
R835
JW8
R860
Q900
JW9
JW49
IC802
R814
JW80
R904
R903
R851
R844 R852
R873
• Semiconductor Location
R925
TP001
R848
R845
C807
C823
C821
C706
R437
D808
D810
C815
CNP800
(Page 27)
26
26
JW1
JW2
JW13
JW15
S802
JW14
JW16
JW17
JW18
JW19
JW20
JW22
JW23
JW24
Q800
JW138
R850
R849
JW25
R804
JW21
R826
JW26
JW29
JR5
R901
JR11
JW12
C812
C813
JW71
D801
L702
L701
JW79
C820
FMB3
C816
R832
R806
JW31
JW77
R840
R841
R822
C818
C817
C824
JW30
JW32
C825
R823
X801
R801
JW28
R709
R703
JW7
JW139
JW33
R828
R821
R854
R819
R834
R809
D811
D812
D813
D814
D816
D820
R813
JW37
JW36
JW38
JW39
JW40
JW41
JW42
JW43
JW46
JW45
R864
R865
JW34
JW35
R815
D815
1
D817
X800
80
JW3
C822
(Page 22)
JW81
R936
R818
Q906
C705
R847
R708
R846
R705
R830
JW136
JW132
JW200
Q907
R825
JW78
C707
JW70
JW69
JW68
D702
R839
R707 R838
IC
FMB4
R833
JW203
JW201
D912
JW85
R853
JW137
JW44
JW204
JW202
R811
JW10
R800
I
JW207
JW205
JW84
R802
R843
R722
R862
R861
JW64
R808
JW135
C414
JW65
JW48
H
JW101
C701
JW72
JW62
S800
JW102
JW103
JW91
C109
JW140
C810
JW11
C802
C801
C410
C411
JR103
C409
JW143
JW67
JW57
JW56
C408
JW53
JW54
JW52
JW55
JW50
JW51
R607
JR10
JW47
JW206
D915
JW87
C709
IC401
R400
R608
TUX601
JW73
JW63
R411
R412
JW88
CN751
JW76
JW74
R401
R603
JW92
C909
C809
JW141
JW142
JW66 C441
R448
R409
L900
JW93
L700
C400
R436
R604
JW104
JW105
JW115
JW114
JW117
JW116
R927
C447
C111
C417
JW94
R837
JW58
F
JW118
C428
C424
R435
R406
R405
R407
JW61
JW59
R447
L400
C416
R404
C452
C619
JW120
C446
C425
C426
C453
Q601
C451
JW122
R417
Q400
R416
R440
R415
R414
C107
C450
JW60
D919
C430
R424
C620
D600
R606
C922
C600
D921
JW121
D400
R615
JW4
JW99
JW100 R932
R432
JW123
R913
D917
JW106
D908
D906
D907
D905
C106
JW125
JW124
JW130
L602
C618
J
R915
Q401
D
G
JW107
D904
Q405
C444
JW98
D916
Q402
JW128
E
R431
R429
Q406
JW5
JW6
R420
Q404
C
C438
R441
R419
Q407
C440
Ref. No.
D400
D600
D801
D808
D810
D811
D812
D813
D814
D815
D816
D817
D820
D902
D903
D904
D905
D906
D907
D908
D909
D912
D914
D915
D916
Location
D-4
E-2
J-5
J-10
J-6
I-3
I-3
I-3
I-2
I-2
I-2
I-2
H-5
B-7
B-8
C-6
C-6
C-7
C-7
C-7
C-7
F-10
C-9
E-10
C-8
Ref. No.
D917
D919
D921
D922
Location
C-8
D-9
D-6
D-6
IC100
IC401
IC801
IC802
B-6
F-4
H-7
H-10
Q400
Q401
Q402
Q403
Q404
Q405
Q406
Q407
Q601
Q800
Q900
Q902
Q906
Q907
D-4
D-4
C-4
D-3
C-3
C-3
C-3
C-3
E-2
I-6
H-10
E-10
F-10
F-10
CDX-R3000/RW300
3-13. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 20 for Circuit Boards Location.
2
1
3
4
5
6
7
8
9
10
11
12
13
14
S507
LED515
S509
LED507
A
S513
S503
LED521
LED503
LED517
B
S515
S516
LED502
LED513
LED501
LCD501
S523
LED514
C
LED516
LED520
IC502
S502
S504
S506
LED522
S511
LED505
S521
LED504
LED524
S508
D
LED525
S505
LED511
S520
LED510
S519
LED509
S518
LED508
LED506
S522
LED518
S517
S510
S512
S501
LED512
S514
(Page 26)
R516
R578
CN901
R577
R575
R576
R574
R557
R554
H
Location
F-13
F-11
F-13
G-12
G-10
G-10
IC501
IC502
IC906
G-7
C-14
G-11
LED501
LED502
C-4
C-11
Ref. No.
LED503
LED504
LED505
LED506
LED507
LED508
LED509
LED510
LED511
LED512
LED513
LED514
LED515
Location
B-8
D-6
D-6
D-10
A-2
D-10
D-9
D-8
D-7
D-12
C-3
C-12
A-13
Ref. No.
LED516
LED517
LED518
LED520
LED521
LED522
LED524
LED525
Location
C-13
B-13
D-11
C-2
B-2
D-5
D-3
D-4
Q501
Q502
G-11
G-10
27
27
R553
C960
R558
IC906
C958
C959
Q501
R511
R512
R555
FMB3
Ref. No.
D502
D503
D504
D521
D551
D552
C553
D551
G
R536
R556
R537
C552
R506
R561
IC501
R579
R552
Q502
R533
R572
R560
R507
R501
R502
R573
R531
D521
R532
R513
R535
R514
D503
FMB4
R534
R580
D552
F
R515
R519
C551
R518
R551
R510
R571
R509
D502
R504
R559
R503
R508
D504
R505
R517
E
CDX-R3000/RW300
3-14. SCHEMATIC DIAGRAM — DISPLAY SECTION —
R534
R552
R551
LED501
R571
LED503
R573
R575
R577
IC906
R579
R537
R533
R532
LED512
LED509
LED505
LED513
LED517
LED518
LED510
LED522
LED521
LED514
LED506
LED511
LED525
LED507
IC502
Q501
C958
C959
C960
D551
LED502
R531
C551
CN901
LED515
R536
D521
IC501
R553
R554
(Page 25)
R556 C552
S523
R555
Q502
R557
LED516
LED508
LED504
LED524
LED520
R558
C553
R559
D504
D503
D502
R560
R572
R535
R574
R576
R578
R580
R561
D552
S513
R511
R512
R513
S514
S515
S516
R514
S517
R515
R516
R517
R518
R519
S518
S519
S520
S521
S522
LCD501
S501
S502
R501
R502
R503
S503
S504
S505
R504
S506
R505
R506
R507
R508
R509
R510
S507
S508
S509
S510
S511
S512
28
28
CDX-R3000/RW300
3-15. IC BLOCK DIAGRAMS
REV
OPIN4(+)
OPIN4(–)
OPOUT4
OPIN3(+)
OPIN3(–)
OPOUT3
MUTE
BIAS
GND
VO3(–)
VO3(+)
VO4(–)
VO4(+)
IC2 BA5966FP-FE2 (SERVO Board)
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MUTE
+
–
+
OUT F
FWD
OUT R
–
+
+
–
+
LEVEL
SHIFT
–
–
+
–
+
1
2
3
4
5
6
7
8
9
10
11
12
13
14
OPIN1(–)
OPOUT1
OPIN2(+)
OPIN2(–)
OPOUT2
VCC
VOL(–)
VOL(+)
VO2(–)
VO2(+)
VO1(–)
VO1(+)
VCC
OPIN1(+)
+
–
LEVEL
SHIFT
+
FWD
–
–
LEVEL
SHIFT
–
+
–
+
+
+
+
REV
–
+
–
+
LOADING DRIVER
–
+
–
LEVEL
SHIFT
–
–
+
+
+
–
–
–
29
CDX-R3000/RW300
DGND
SDA
SCL
MUTE
SEL
ADJ
VCC
OUTF1
OUTR1
OUTF2
OUTR2
DS12
DS22
DS32
OUTS1
OUTS2
IC401 BD3808FS (MAIN Board)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
2
I C BUS
LOGIC
FADER
(0~-58,
-∞dB)
VCO
FADER
(0~-58,
-∞dB)
FADER
(0~-58,
-∞dB)
EFFECT (0dB~
+20dB,2dB STEP)
BASS
fo:60,70,80,100,120,140,160,200Hz
Q:0.5,0.75,1,1.25
FADER
(0~-58,
-∞dB)
EFFECT (0dB~
+20dB,2dB STEP)
GAIN+ATT
(+10~-29,
-∞dB)
2ND ORDER LPF
fc:OFF,80,120,160Hz
Q: 0.707
2ND ORDER
LPF
MIX
TONE
PASS
TONE
PASS
MIDDLE
fo:500Hz,1kHz
Q:1
BASS,TREBLE, MIDDLE
(-15dB~+15dB,1dB STEP)
BASS,TREBLE, MIDDLE
(-15dB~+15dB,1dB STEP)
TABLE
fo:5,7.5,10,12.5kHz
VOLUME
(+23~-79dB,-∞dB
1dB STEP)
VOLUME
(+23~-79dB,-∞dB
1dB STEP)
fc:40kHz
fc:40kHz
ANTI-ALIASING
FILTER
ANTI-ALIASING
FILTER
INPUT GAIN
(0~15dB,1dB STEP)
INPUT GAIN
(0~15dB,1dB STEP)
MUTE
MUTE
INPUT SELECTOR
(4 STEREO INCLUDE 1 ISOLATION INPUT)
30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
AGND
FIL
AP1
AN
AP2
B1
B2
C1
C2
D1
D2
DS11
DS21
DS31
NC
NC
VCC/2
CDX-R3000/RW300
SECTION 4
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
• Accessories are given in the last of this
parts list.
• Abbreviation
CND : Canadian model
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
4-1. MAIN SECTION
A
MG-611XA-186//K
#1
#1
not supplied
6
B
A
F901
5
#2
4
TUX601
3
7
#1
not supplied
B
2
#1
#1
1
Ref. No.
Part No.
Description
1
2
3
* 4
5
X-3384-407-1
3-231-472-01
X-3382-588-1
3-246-006-31
3-922-535-11
PANEL (1) ASSY, SUB
SCREW (+B 2X4)
LOCK ASSY (S)
COVER
SCREW (+BTT)
6
1-776-206-21 CORD (WITH CONNECTOR) (POWER)
Remark
Ref. No.
Part No.
Description
7
7
F901
TUX601
#1
A-3283-418-A
A-3283-489-A
1-532-877-11
A-3220-959-A
7-685-792-09
MAIN BOARD, COMPLETE (US,CND)
MAIN BOARD, COMPLETE (E)
FUSE (BLADE TYPE) (AUTO FUSE) 10A
TUNER UNIT (TUX-032)
SCREW +PTT 2.6X6 (S)
#2
7-685-793-09 SCREW +PTT 2.6X8 (S)
Remark
31
CDX-R3000/RW300
4-2. FRONT PANEL SECTION
61
60
59
58
#3
not supplied
(DISPLAY board)
not supplied
#3
57
LCD901
not supplied
64
56
62
not supplied
not
supplied
55
not supplied
63
54
52
51
53
Ref. No.
Part No.
Description
Part No.
Description
51
51
51
52
53
X-3384-410-1
X-3384-617-1
X-3384-687-1
3-258-879-01
3-258-874-01
PANEL (BASE) ASSY, FRONT (R3000:US,CND)
PANEL (BASE) ASSY, FRONT (RW300)
PANEL (BASE) ASSY, FRONT (R3000:E)
FILTER (IR)
BUTTON (SEEK)
59
60
61
61
61
3-258-869-01
X-3378-390-3
A-3372-585-A
A-3372-726-A
A-3372-777-A
PANEL, FRONT BACK
CASE ASSY (for FRONT PANEL)
PANEL OVERALL ASSY, FRONT (R3000:US,CND)
PANEL OVERALL ASSY, FRONT (RW300)
PANEL OVERALL ASSY, FRONT (R3000:E)
54
55
56
57
58
X-3384-070-1
3-258-873-01
3-246-211-01
3-258-884-01
3-258-880-01
RETRACTABLE ASSY
BUTTON (+,–)
SPRING (RELEASE)
SHEET (ILLUMINATOR)
PLATE (CD), LIGHT GUIDE
62
63
64
LCD901
#3
3-258-875-01
X-3384-457-1
1-780-120-11
1-805-450-11
7-685-105-19
BUTTON (PRESET)
BUTTON ASSY (S)
CONDUCTIVE BOARD, CONNECTION
DISPLAY PANEL, LIQUID CRYSTAL
SCREW +P 2X8 TYPE2 NON-SLIT
32
Remark
Ref. No.
Remark
CDX-R3000/RW300
4-3. CD MECHANISM SECTION (1)
(MG-611XA-186//K)
not supplied
102
not supplied
(SENSOR board)
101
#4
not supplied
not supplied
103
104
106
105
108
107
Ref. No.
101
102
103
104
105
Part No.
Description
A-3372-455-A
3-253-729-01
3-253-746-01
3-253-746-11
3-253-695-01
CHASSIS (T) SUB ASSY
SPRING (LTR), TENSION COIL
SPRING (DAMPER), COMPRESSION
SPRING (DAMPER), COMPRESSION
SPRING (KF), TENSION COIL
Remark
Ref. No.
106
107
108
#4
Part No.
Description
3-253-748-01
3-352-758-31
A-3283-350-A
7-627-552-87
DAMPER(S)
SCREW (M1.7), TOOTHED LOCK
SERVO BOARD, COMPLETE
SCREW, PRECISION +P 1.7X2.2
Remark
33
CDX-R3000/RW300
(MG-611XA-186//K)
155
156
157
154
(including M901)
#5
M902
not supplied
SW4
not supplied
158
not supplied
153
not supplied
151
152
specified.
Ref. No.
Part No.
Description
151
152
0 153
154
155
A-3337-637-A
4-912-432-01
8-820-207-02
A-3337-640-A
A-3337-641-A
CHASSIS (OP) COMPLETE ASSY
SCREW (B1.4X5), TAPPING
OPTICAL PICK-UP KSS1000E/K1RP
CHASSIS (OP) SUB ASSY (including M901)
ARM SUB ASSY, CHUCKING
156
34
A-3337-639-A LEVER (SL) SUB ASSY
Remark
Ref. No.
157
158
M902
SW4
#5
la sécurité.
Part No.
Description
X-3383-454-2
3-261-959-01
A-3337-638-A
1-571-099-11
7-627-850-77
LEVER (SL) ASSY
SPRING (SL), TORSION
MOTOR ASSY, SL (SLED)
SWITCH (1 KEY) (LIMIT)
SCREW, PRECISION +P 1.4X1.8
Remark
CDX-R3000/RW300
(MG-611XA-186//K)
203
201
202
207
211
204
209
208
210
205
207
207
M903
#4
206
Ref. No.
Part No.
Description
201
202
203
204
205
3-338-647-31
3-259-024-01
A-3337-633-A
3-259-455-01
3-253-713-01
WASHER (1.0-2.5)
WHEEL (RA), WORM
ARM ASSY, ROLLER
SPRING (RAL)
SPRING (RAR)
206
207
3-259-469-01 SPRING (LE), LEAF
2-134-636-31 SCREW (M1.7X2.5)
Remark
Ref. No.
Part No.
Description
208
209
210
211
M903
3-259-467-01
3-345-648-91
A-3372-456-A
3-259-468-01
A-3372-454-A
BRACKET (LEM)
SCREW (M1.4), TOOTHED LOCK
WORM (LEB) ASSY
BEARING (LEB)
MOTOR ASSY, LE (LOADING)
#4
7-627-552-87 SCREW, PRECISION +P 1.7X2.2
Remark
35
CDX-R3000/RW300
(MG-611XA-186//K)
254
252
255
252
256
251
253
257
Ref. No.
251
252
253
254
36
Part No.
Description
3-259-429-01
3-344-223-01
3-259-470-01
3-253-755-01
WHEEL (LE), WORM
WASHER
GEAR (LE1)
LEVER (D)
Remark
Ref. No.
255
256
257
Part No.
Description
3-899-829-01 WASHER (SLIT)
3-259-032-01 GEAR (LE2)
A-3372-453-A CHASSIS (M) BLOCK ASSY
Remark
CDX-R3000/RW300
SECTION 5
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
• Abbreviation
When indicating parts by reference
number, please include the board.
Ref. No.
Part No.
Description
Remark
DISPLAY BOARD
**************
1-780-120-11 CONDUCTIVE BOARD, CONNECTION
3-258-884-01 SHEET (ILLUMINATOR)
< CAPACITOR >
C551
C552
C553
C958
C959
1-164-227-11
1-162-963-11
1-125-891-11
1-125-837-11
1-125-837-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C960
1-107-826-11 CERAMIC CHIP
0.022uF
680PF
0.47uF
1uF
1uF
10%
10%
10%
10%
10%
25V
50V
10V
6.3V
6.3V
0.1uF
10%
16V
< CONNECTOR >
CN901
1-794-312-21 PIN, CONNECTOR 12P
< DIODE >
D502
D503
D504
D521
D551
8-719-978-33
8-719-978-33
8-719-978-33
8-719-988-61
8-719-069-54
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ-TT11-6.8B
DTZ-TT11-6.8B
DTZ-TT11-6.8B
1SS355TE-17
UDZS-TE17-5.1B
D552
8-719-988-61 DIODE 1SS355TE-17
< IC >
IC501
IC502
IC906
6-705-180-01 IC LC75827W
6-600-321-01 IC KSM-401Y (IR)
6-705-374-01 IC MM3033DULE
< LIQUID CRYSTAL DISPLAY >
LCD901 1-805-450-11 DISPLAY PANEL, LIQUID CRYSTAL
< DIODE >
LED501
LED502
LED503
LED503
LED504
6-500-459-01
6-500-459-01
6-500-511-01
8-719-082-38
6-500-510-01
LED
LED
LED
LED
LED
NSCW505T-ARS (LCD BACK LIGHT)
CL-270PG-C-TS (DISC IND) (RW300)
CL-270SR-C-TS (DISC IND) (R3000)
CL-195PG-CD-T (2) (RW300)
LED504
LED505
LED505
LED506
LED506
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
LED
SML-310VT-T86 (2) (R3000)
CL-195PG-CD-T (1) (RW300)
SML-310VT-T86 (1) (R3000)
CL-195PG-CD-T (SENS) (RW300)
SML-310VT-T86 (SENS) (R3000)
Ref. No.
DISPLAY
specified.
la sécurité.
Part No.
Description
Remark
LED507
LED507
LED508
LED508
LED509
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
LED
LED
LED
LED
LED
CL-195PG-CD-T (ATT) (RW300)
SML-310VT-T86 (ATT) (R3000)
CL-195PG-CD-T (6) (RW300)
SML-310VT-T86 (6) (R3000)
CL-195PG-CD-T (5) (RW300)
LED509
LED510
LED510
LED511
LED511
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
LED
SML-310VT-T86 (5) (R3000)
CL-195PG-CD-T (4) (RW300)
SML-310VT-T86 (4) (R3000)
CL-195PG-CD-T (3) (RW300)
SML-310VT-T86 (3) (R3000)
LED512
LED512
LED513
LED513
LED514
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
LED
LED
LED
LED
LED
CL-195PG-CD-T (SHUF) (RW300)
SML-310VT-T86 (SHUF) (R3000)
CL-195PG-CD-T (DSPL) (RW300)
SML-310VT-T86 (DSPL) (R3000)
CL-195PG-CD-T (EQ3) (RW300)
LED514
LED515
LED515
LED516
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
LED
LED
LED
LED
SML-310VT-T86 (EQ3) (R3000)
CL-195PG-CD-T (OFF) (RW300)
SML-310VT-T86 (OFF) (R3000)
CL-195PG-CD-T (SEEK – m .)
(RW300)
LED516 8-719-053-09 LED SML-310VT-T86 (SEEK – m .)
(R3000)
LED517 6-500-510-01 LED CL-195PG-CD-T (SEEK + > M)
(RW300)
LED517 8-719-053-09 LED SML-310VT-T86 (SEEK + > M)
(R3000)
LED518 6-500-510-01 LED CL-195PG-CD-T (REP) (RW300)
LED518 8-719-053-09 LED SML-310VT-T86 (REP) (R3000)
LED520 6-500-510-01 LED CL-195PG-CD-T (VOLUME –) (RW300)
LED520
LED521
LED521
LED522
LED522
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
LED
SML-310VT-T86 (VOLUME –) (R3000)
CL-195PG-CD-T (VOLUME +) (RW300)
SML-310VT-T86 (VOLUME +) (R3000)
CL-195PG-CD-T (SEL) (RW300)
SML-310VT-T86 (SEL) (R3000)
LED524
LED524
LED525
LED525
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
CL-195PG-CD-T (SOURCE) (RW300)
SML-310VT-T86 (SOURCE) (R3000)
CL-195PG-CD-T (MODE) (RW300)
SML-310VT-T86 (MODE) (R3000)
< TRANSISTOR >
Q501
Q502
8-729-900-53 TRANSISTOR DTC114EK
8-729-900-53 TRANSISTOR DTC114EK
< RESISTOR >
R501
1-216-819-11 METAL CHIP
680
5%
1/10W
37
CDX-R3000/RW300
DISPLAY
Ref. No.
MAIN
Part No.
Description
R502
R503
R504
R505
R506
1-216-819-11
1-216-819-11
1-216-821-11
1-216-823-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
1K
1.5K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R507
R508
R509
R510
R511
1-216-825-11
1-216-827-11
1-216-829-11
1-218-867-11
1-216-819-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
3.3K
4.7K
6.8K
680
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R512
R513
R514
R515
R516
1-216-819-11
1-216-819-11
1-216-821-11
1-216-823-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
1K
1.5K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R517
R518
R519
R531
R532
1-216-825-11
1-216-827-11
1-216-829-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
3.3K
4.7K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R533
R534
R535
R536
R537
1-216-809-11
1-216-826-11
1-216-826-11
1-216-813-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
2.7K
2.7K
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R551
R552
R553
R554
R555
1-216-825-11
1-216-815-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
330
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R556
R557
R558
R559
R560
1-216-840-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
39K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R561
R571
1-216-857-11 METAL CHIP
1-216-808-11 METAL CHIP
1M
82
5%
5%
R571
1-216-809-11 METAL CHIP
100
5%
R572
1-216-808-11 METAL CHIP
82
5%
R572
1-216-809-11 METAL CHIP
100
5%
1/10W
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
R573
1-216-808-11 METAL CHIP
82
5%
R573
1-216-809-11 METAL CHIP
100
5%
R574
1-216-808-11 METAL CHIP
82
5%
R574
1-216-809-11 METAL CHIP
100
5%
R575
1-216-808-11 METAL CHIP
82
5%
R575
1-216-809-11 METAL CHIP
100
5%
R576
1-216-808-11 METAL CHIP
82
5%
R576
1-216-809-11 METAL CHIP
100
5%
38
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
Ref. No.
Part No.
Description
Remark
R577
1-216-808-11 METAL CHIP
82
5%
R577
1-216-809-11 METAL CHIP
100
5%
R578
1-216-808-11 METAL CHIP
82
5%
R578
1-216-809-11 METAL CHIP
100
5%
R579
1-216-808-11 METAL CHIP
82
5%
R579
1-216-809-11 METAL CHIP
100
5%
R580
1-216-808-11 METAL CHIP
82
5%
R580
1-216-809-11 METAL CHIP
100
5%
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
< SWITCH >
S501
S502
S503
S504
S505
1-786-653-11
1-786-653-11
1-771-884-31
1-771-884-31
1-771-884-31
SWITCH, TACTILE (OPEN/EJECT)
SWITCH, TACTILE (OFF)
SWITCH, TACTILE (SOURCE)
SWITCH, TACTILE (MODE)
S506
S507
S508
S509
S510
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
SWITCH, TACTILE (SEL)
SWITCH, TACTILE (VOLUME +)
SWITCH, TACTILE (VOLUME –)
SWITCH, TACTILE (ATT)
SWITCH, TACTILE (BTM/SENS)
S511
S512
S513
S514
S515
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
SWITCH, TACTILE (1)
SWITCH, TACTILE (2)
SWITCH, TACTILE (SEEK + > M)
SWITCH, TACTILE (SEEK – m .)
SWITCH, TACTILE (EQ3)
S516
S517
S518
S519
S520
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
SWITCH, TACTILE (DSPL)
SWITCH, TACTILE (SHUF)
SWITCH, TACTILE (6)
SWITCH, TACTILE (5)
SWITCH, TACTILE (4)
S521
1-771-884-31 SWITCH, TACTILE (3)
S522
1-771-884-31 SWITCH, TACTILE (REP)
S523
1-529-566-61 SWITCH, PUSH (1 KEY) (OPEN/EJECT)
*************************************************************
A-3283-418-A MAIN BOARD, COMPLETE (including
SPEAKER BOARD) (US,CND)
A-3283-489-A MAIN BOARD, COMPLETE (including
SPEAKER BOARD) (E)
*********************
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-685-795-09 SCREW +PTT 2.6X12 (S)
< CAPACITOR >
C101
C106
C107
C108
C109
1-124-233-11
1-124-234-00
1-124-233-11
1-216-864-11
1-124-233-11
ELECT
ELECT
ELECT
METAL CHIP
ELECT
C111
C113
1-124-233-11 ELECT
10uF
22uF
10uF
0
10uF
20%
20%
20%
5%
20%
16V
16V
16V
1/10W
16V
10uF
0.47uF
20%
10%
16V
16V
CDX-R3000/RW300
MAIN
Ref. No.
Part No.
Description
C303
C400
C406
C407
C408
1-216-864-11
1-162-970-11
1-136-154-00
1-162-965-11
1-115-467-11
METAL CHIP
CERAMIC CHIP
FILM
CERAMIC CHIP
CERAMIC CHIP
0
0.01uF
0.012uF
0.0015uF
0.22uF
5%
10%
5%
10%
10%
1/10W
25V
50V
50V
10V
Remark
C409
C410
C411
C414
C416
1-115-467-11
1-104-942-11
1-104-942-11
1-128-428-11
1-162-970-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.22uF
1uF
1uF
10uF
0.01uF
10%
20%
20%
20%
10%
10V
50V
50V
35V
25V
C417
C424
C425
C426
C428
1-124-589-11
1-128-428-11
1-128-428-11
1-128-428-11
1-128-428-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
10uF
10uF
10uF
10uF
20%
20%
20%
20%
20%
16V
35V
35V
35V
35V
C430
C435
C436
C437
C438
1-126-947-11
1-162-927-11
1-162-927-11
1-125-891-11
1-125-891-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
100PF
100PF
0.47uF
0.47uF
20%
5%
5%
10%
10%
16V
50V
50V
10V
10V
C440
C441
C444
C446
C447
1-125-891-11
1-115-467-11
1-125-891-11
1-162-923-11
1-124-257-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.47uF
0.22uF
0.47uF
47PF
2.2uF
10%
10%
10%
5%
20%
10V
10V
10V
50V
50V
C450
C451
C452
C453
C600
1-162-927-11
1-162-927-11
1-128-428-11
1-128-428-11
1-216-864-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
METAL CHIP
100PF
100PF
10uF
10uF
0
5%
5%
20%
20%
5%
50V
50V
35V
35V
1/10W
C618
C619
C620
C701
C704
1-126-786-11
1-124-247-61
1-107-826-11
1-124-584-00
1-124-584-00
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
47uF
10uF
0.1uF
100uF
100uF
20%
20%
10%
20%
20%
16V
35V
16V
10V
10V
C705
C706
C707
C709
C801
1-124-584-00
1-162-964-11
1-124-584-00
1-162-964-11
1-107-826-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
0.001uF
100uF
0.001uF
0.1uF
20%
10%
20%
10%
10%
10V
50V
10V
50V
16V
C802
C807
C809
C810
C812
1-124-589-11
1-162-970-11
1-124-584-00
1-125-701-11
1-107-826-11
ELECT
CERAMIC CHIP
ELECT
DOUBLE LAYERS
CERAMIC CHIP
47uF
0.01uF
100uF
0.047F
0.1uF
20%
10%
20%
10%
16V
25V
10V
5.5V
16V
C813
C815
C816
C817
C818
1-124-584-00
1-162-964-11
1-164-160-11
1-162-918-11
1-164-160-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.001uF
20PF
18PF
20PF
20%
10%
5%
5%
5%
10V
50V
50V
50V
50V
C820
C821
C822
C823
C824
1-162-920-11
1-107-826-11
1-107-826-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
27PF
0.1uF
0.1uF
100PF
100PF
5%
10%
10%
5%
5%
50V
16V
16V
50V
50V
C825
C908
1-124-584-00 ELECT
1-126-160-11 ELECT
100uF
1uF
20%
20%
Ref. No.
Part No.
Description
Remark
C908
1-126-960-11 ELECT
1uF
20%
50V
C909
C922
1-131-868-81 ELECT
0.01uF
3300uF
10%
20%
25V
16V
(E)
< CONNECTOR >
CN751
CNP800
CNP900
CNP901
1-817-536-11
1-794-311-21
1-764-270-21
1-774-701-21
CONNECTOR, BOARD TO BOARD 28P
PLUG, CONNECTOR 12P
JACK (REMOTE IN) (E)
PIN, CONNECTOR 16P
< DIODE >
D400
D600
D702
D801
D808
8-719-988-61
8-719-069-55
1-216-864-11
8-719-988-61
8-719-977-12
DIODE 1SS355TE-17
DIODE UDZS-TE17-5.6B
METAL CHIP
0
DIODE 1SS355TE-17
DIODE DTZ6.8B
D810
D811
D812
D813
D814
8-719-988-61
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17 (E)
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
D815
D816
D817
D820
D902
8-719-109-97
8-719-109-97
8-719-109-97
8-719-991-33
8-719-053-18
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
1SS133T-77
1SR154-400TE-25
D903
D904
D905
D906
D907
8-719-053-18
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
11ES2
11ES2
11ES2
11ES2
D908
D909
D912
D914
D915
8-719-200-82
8-719-200-82
8-719-083-66
8-719-977-12
8-719-056-84
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
UDZSTE-1718B
DTZ6.8B
UDZSTE-177.5B
D916
D917
D919
D921
D922
8-719-200-82
8-719-200-82
8-719-049-38
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
1N5404TU
11ES2
11ES2
5%
1/10W
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< IC >
IC100
IC401
IC801
IC802
6-705-360-01
6-705-372-01
6-803-820-01
8-759-659-13
IC
IC
IC
IC
TDA8588BJ/N2
BD3808FS-FE2
MB90473PF-G166-BNDE1
PST3428UL
< JUMPER RESISTOR >
JR5
JR6
JR10
JR11
JR103
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
10V
50V
(US,CND)
39
CDX-R3000/RW300
MAIN
Ref. No.
Part No.
Description
Remark
< COIL >
L400
L602
L700
L701
L702
1-414-398-11
1-414-394-41
1-410-501-11
1-410-501-11
1-410-509-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
L900
1-456-617-11 COIL, CHOKE
10uH
2.2uH
2.2uH
2.2uH
10uH
250uH
< JACK >
PJ401
PJ601
1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR)
1-793-598-11 JACK (ANTENNA)
Ref. No.
Part No.
Description
R448
R603
R604
R606
R607
1-216-841-11
1-247-807-31
1-247-807-31
1-216-809-11
1-216-809-11
METAL CHIP
CARBON
CARBON
METAL CHIP
METAL CHIP
47K
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
1/10W
1/10W
Remark
R608
R615
R703
R705
R707
1-216-809-11
1-216-821-11
1-216-864-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
0
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R709
R722
R800
1-216-864-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-841-11 METAL CHIP
0
100
47K
5%
5%
5%
R801
R802
1-216-809-11 METAL CHIP
1-216-864-11 METAL CHIP
100
0
5%
5%
1/10W
1/10W
1/10W
(E)
1/10W
1/10W
R804
R805
R806
R808
1-216-809-11
1-218-871-11
1-218-871-11
1-216-845-11
100
10K
10K
100K
5%
0.5%
0.5%
5%
R808
1-216-864-11 METAL CHIP
0
5%
R809
1-216-845-11 METAL CHIP
100K
5%
R810
R811
R813
R814
1-216-845-11
1-216-845-11
1-249-441-11
1-216-845-11
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
100K
100K
100K
100K
5%
5%
5%
5%
1/10W
(E)
1/10W
1/10W
1/4W
1/10W
R815
R818
R819
R821
R822
1-249-435-11
1-216-809-11
1-216-809-11
1-216-817-11
1-216-817-11
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
100
100
470
470
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
R823
R824
R825
R826
R828
1-216-817-11
1-216-849-11
1-216-849-11
1-216-843-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
220K
220K
68K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R830
R832
R833
R834
R835
1-216-809-11
1-216-867-11
1-249-417-11
1-216-867-11
1-216-845-11
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
100
6.8K
1K
6.8K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/10W
R837
R838
R839
R840
R841
1-216-864-11
1-216-845-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R843
R844
R846
R847
R848
1-216-809-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R849
R850
R851
R852
R853
1-216-841-11
1-218-871-11
1-216-809-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10K
100
0
0
5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< TRANSISTOR >
Q400
Q401
Q402
Q403
Q404
8-729-038-71
8-729-038-55
6-550-752-01
6-550-752-01
6-550-752-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KRC107S
KRA103S
DTC614TKT146
DTC614TKT146
DTC614TKT146
Q405
Q406
Q407
Q601
Q800
6-550-752-01
6-550-752-01
6-550-752-01
8-729-920-85
8-729-038-55
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC614TKT146
DTC614TKT146
DTC614TKT146
2SD1664-QR
KRA103S
Q900
Q902
Q906
Q907
8-729-034-51
8-729-038-67
8-729-034-51
8-729-038-67
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KTC3875
KRC102S
KTC3875
KRC102S
< RESISTOR >
R404
R405
R406
R407
R409
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R411
R412
R414
R415
R416
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R417
R418
R419
R420
R421
1-216-809-11
1-216-841-11
1-216-841-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R424
R427
R429
R431
R432
1-216-805-11
1-216-809-11
1-247-807-31
1-247-807-31
1-216-809-11
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
47
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/10W
R435
R436
R437
R440
R441
1-216-809-11
1-216-809-11
1-216-821-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
1K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R442
R443
R447
1-216-841-11 METAL CHIP
1-216-841-11 METAL CHIP
1-216-809-11 METAL CHIP
47K
47K
100
5%
5%
5%
1/10W
1/10W
1/10W
40
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1/10W
1/10W
1/10W
1/10W
(E)
1/10W
(US,CND)
CDX-R3000/RW300
MAIN
Ref. No.
Part No.
Description
SENSOR
SERVO
Remark
Ref. No.
Part No.
Description
C18
C19
C20
C21
C23
1-162-970-11
1-107-826-11
1-107-826-11
1-162-970-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.01uF
47PF
10%
10%
10%
10%
5%
25V
16V
16V
25V
50V
5%
1/10W
1/10W
1/10W
(E)
1/10W
(E)
1/4W
100K
100K
100K
4.7K
47K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
C25
C26
C27
C28
C29
1-162-908-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
3PF
0.1uF
0.1uF
0.1uF
0.1uF
0.25PF
10%
10%
10%
10%
50V
16V
16V
16V
16V
1-216-841-11
1-249-417-11
1-216-821-11
1-469-144-21
1-469-144-21
METAL CHIP
47K
CARBON
1K
METAL CHIP
1K
FERRITE, EMI (SMD) (E)
FERRITE, EMI (SMD) (E)
5%
5%
5%
1/10W
1/4W
1/10W
C30
C31
C32
C34
C35
1-162-921-11
1-162-925-11
1-107-826-11
1-107-826-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
33PF
68PF
0.1uF
0.1uF
0.01uF
5%
5%
10%
10%
10%
50V
50V
16V
16V
25V
R917
R925
R927
R928
R931
1-249-421-11
1-216-845-11
1-216-833-11
1-249-421-11
1-216-073-00
CARBON
METAL CHIP
METAL CHIP
CARBON
RES-CHIP
2.2K
100K
10K
2.2K
10K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/4W
1/10W
C36
C37
C38
C39
C70
1-162-967-11
1-162-970-11
1-104-609-11
1-107-826-11
1-162-965-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0033uF
0.01uF
100uF
0.1uF
0.0015uF
10%
10%
20%
10%
10%
50V
25V
4V
16V
50V
R932
R936
1-216-073-00 RES-CHIP
1-216-864-11 METAL CHIP
10K
0
5%
5%
1/10W
1/10W
C71
C72
C73
C74
C75
1-162-965-11
1-162-962-11
1-162-962-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF
470PF
470PF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
16V
16V
C76
C77
C78
C79
1-162-970-11
1-162-970-11
1-164-227-11
1-164-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.022uF
0.022uF
10%
10%
10%
10%
25V
25V
25V
25V
R854
R860
R861
1-216-864-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-809-11 METAL CHIP
0
100K
100
5%
5%
5%
R862
1-216-809-11 METAL CHIP
100
5%
R864
1-249-441-11 CARBON
100K
R865
R873
R901
R902
R903
1-249-441-11
1-216-845-11
1-216-845-11
1-216-829-11
1-216-841-11
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R904
R912
R913
R914
R915
Remark
< SWITCH >
S800
S802
1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) (E)
1-762-638-21 SWITCH, TACTILE (RESET)
< TUNER >
< CONNECTOR >
TUX601 A-3220-959-A TUNER UNIT (TUX-032)
CN1
CN2
< VIBRATOR >
X800
1-767-993-21 VIBRATOR, CRYSTAL (3.68MHz)
X801
1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
1-817-275-21 CONNECTOR, BOARD TO BOARD 28P
1-794-153-21 CONNECTOR, FPC (ZIF) 16P
< FERRITE BEAD >
FB1
1-414-760-21 FERRITE, EMI (SMD)
SENSOR BOARD
**************
< IC >
IC1
IC2
< SWITCH >
SW2
1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)
SW3
1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)
*************************************************************
A-3283-350-A SERVO BOARD, COMPLETE
**********************
6-703-699-01 IC uPD63712GC-8EU-A
6-705-002-01 IC BA5966FP-FE2
< FERRITE BEAD >
JR40
JR41
JR90
JR91
1-414-760-21
1-414-760-21
1-414-760-21
1-414-760-21
< CAPACITOR >
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
< TRANSISTOR >
C1
C2
C3
C5
C6
1-107-826-11
1-162-970-11
1-107-826-11
1-107-826-11
1-100-381-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.01uF
0.1uF
0.1uF
10uF
10%
10%
10%
10%
20%
16V
25V
16V
16V
16V
C7
C8
C11
C13
C17
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
Q1
8-729-904-87 TRANSISTOR 2SB1197K-R
< RESISTOR >
R1
R6
R7
R9
R11
1-216-841-11
1-216-833-11
1-216-840-11
1-216-822-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R12
1-216-809-11 METAL CHIP
47K
10K
39K
1.2K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
100
5%
1/10W
41
CDX-R3000/RW300
SERVO
Ref. No.
Part No.
Description
R13
R14
R15
R41
R42
1-216-833-11
1-216-797-11
1-216-797-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10
10
1K
1K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R44
R45
R70
R71
R72
1-414-760-21
1-414-760-21
1-216-842-11
1-216-833-11
1-216-842-11
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
METAL CHIP
56K
METAL CHIP
10K
METAL CHIP
56K
5%
5%
5%
1/10W
1/10W
1/10W
R73
R74
R75
R76
R77
1-216-833-11
1-216-837-11
1-216-833-11
1-216-837-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
22K
10K
22K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R78
R79
R80
R81
R82
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R83
R84
R85
1-216-833-11 METAL CHIP
1-216-837-11 METAL CHIP
1-216-833-11 METAL CHIP
10K
22K
10K
5%
5%
5%
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
Remark
ACCESSORIES
************
3-261-844-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(R3000:US,CND)
3-261-844-21 MANUAL, INSTRUCTION (ENGLISH,SPANISH,
TRADITIONAL CHINESE) (R3000:E)
3-261-844-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(RW300)
3-261-846-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRENCH) (R3000:US,CND)
SPANISH,TRADITIONAL CHINESE)
(R3000:E)
SPANISH) (RW300)
X-3378-390-3 CASE ASSY (for FRONT PANEL)
*************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
301
302
303
304
305
X-3382-647-1
X-3366-405-1
3-934-325-01
3-260-282-01
3-246-471-01
FRAME ASSY, FITTING
SCREW ASSY (EXP), FITTING (E)
SCREW (+K 5X8 TP)
COLLAR
KEY (FRAME)
306
1-776-206-21 CORD (WITH CONNECTOR) (POWER)
< SWITCH >
SW1
1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)
< VIBRATOR >
301
302
X1
1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz)
*************************************************************
MISCELLANEOUS
***************
6
0 153
154
F901
M902
1-776-206-21
8-820-207-02
A-3337-640-A
1-532-877-11
A-3337-638-A
303
304
305
306
CORD (WITH CONNECTOR) (POWER)
OPTICAL PICK-UP KSS1000E/K1RP
CHASSIS (OP) SUB ASSY (including M901)
FUSE (BLADE TYPE) (AUTO FUSE) 10A
MOTOR ASSY, SL (SLED)
M903
A-3372-454-A MOTOR ASSY, LE (LOADING)
SW4
1-571-099-11 SWITCH (1 KEY) (LIMIT)
*************************************************************
42
specified.
la sécurité.
CDX-R3000/RW300
US Model
CDX-R3000/RW300
Canadian Model
E Model
SERVICE MANUAL
CDX-R3000
Ver. 1.1 2005.07
SUPPLEMENT-1
File this supplement with the service manual.
Subject : Change of display board.
When performing service and inspection, check the suffix of the part number
of the display board.
DISCRIMINATION
– DISPLAY BOARD (SIDE B) –
DISPLAY BOARD Part No.
Former : 1-861-024-11
New : 1-861-024-13
9-961-386-81
CDX-R3000/RW300
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• C : panel designation.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
•
: Through hole.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
•
•
•
•
•
•
•
•
•
•
•
2
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
CD mechanism section
no mark : CD PLAY
Main (1/2), (2/2) and Display sections
no mark : FM
(
) : AM
<
> : CD PLAY
∗
: Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
Waveforms are taken with a oscilloscope.
Circled numbers refer to waveforms.
Signal path.
J : CD PLAY
F : FM
f : AM
Abbreviation
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
C
Q
These are omitted
B E
BE C
These are omitted
ECB
These are omitted
• Abbreviation
CDX-R3000/RW300
4
5
6
7
8
9
10
11
12
13
14
LED515
S513
LED507
S509
A
3
S507
2
1
S503
1. PRINTED WIRING BOARD — DISPLAY SECTION —
LED521
LED503
LED517
B
S516
S515
LCD501
S522
LED513
LED502
LED514
LED501
C
LED516
IC502
LED522
LED525
S502
S504
LED524
S505
S506
LED505
LED504
S511
S512
LED511
S521
LED510
S520
LED509
S519
LED508
S518
LED518
LED506
S510
S523
S514
S508
LED520
LED512
S501
S517
D
E
R503
R504
R515
R517
R518
R516
CN901
R575
R574
R576
R501
R514
Ref. No.
D502
D503
D504
D551
D552
Location
F-13
F-11
F-13
G-10
G-10
IC501
IC502
IC906
G-7
C-14
G-11
LED501
LED502
C-4
C-11
Ref. No.
LED503
LED504
LED505
LED506
LED507
LED508
LED509
LED510
LED511
LED512
LED513
LED514
Location
B-8
D-6
D-6
D-10
A-2
D-10
D-9
D-8
D-7
D-12
C-3
C-12
Ref. No.
LED515
LED516
LED517
LED518
LED520
LED521
LED522
LED524
LED525
Location
A-13
C-13
B-13
D-11
C-2
B-2
D-5
D-3
D-4
Q502
G-10
3
3
C960
R553
R559
R551
R560
R573
R502
R572
R511
R558
R512
R571
R561
H
R555
D551
FMB3
R557 C553
R554
C552
R537 R536
R556
R506
D552
IC501
R579
IC906
R507
R533
D503
R535
R531
R552
R532
Q502
R513
C958
R580
FMB4
G
D502
R577
C551
R519
R578
F
R510
R509
D504
R505
R508
CDX-R3000/RW300
2. SCHEMATIC DIAGRAM — DISPLAY SECTION —
R552
R551
LED501
R573
R571
LED503
R575
R577
IC906
R579
R537
LED515
R533
R532
LED509
LED505
LED513
IC502
LED502
D551
C958
R531
LED518
LED510
LED522
LED521
LED514
LED506
LED511
LED525
LED507
C551
LED517
C960
CN901
LED512
R536
IC501
R553
R554
R556 C552
S522
R555
Q502
R557
D504
D503
D502
LED516
R574
R572
R535
LED508
LED504
LED524
R576
R578
LED520
R580
R558
R559
R560
C553
R561
D552
S513
R511
R512
R513
R514
R515
R516
R517
R518
R519
S514
S515
S516
S517
S518
S519
S520
S521
S523
LCD501
S501
S502
R501
R502
R503
R504
R505
R506
R507
R508
R509
R510
S503
S504
S505
S506
S507
S508
S509
S510
S511
S512
4
4
CDX-R3000/RW300
DISPLAY
3. ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Abbreviation
Ref. No.
Part No.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
Description
Remark
1-780-120-11 CONDUCTIVE BOARD, CONNECTION
3-258-884-01 SHEET (ILLUMINATOR)
< CAPACITOR >
1-164-227-11
1-162-963-11
1-125-891-11
1-125-837-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
680PF
0.47uF
1uF
0.1uF
10%
10%
10%
10%
10%
25V
50V
10V
6.3V
16V
< CONNECTOR >
CN901
1-794-312-21 PIN, CONNECTOR 12P
< DIODE >
D502
D503
D504
D551
D552
8-719-977-12
8-719-977-12
8-719-977-12
8-719-080-28
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ6.8B
DTZ6.8B
DTZ6.8B
KDZ5.1V
1SS355TE-17
< IC >
IC501
IC502
IC906
la sécurité.
When indicating parts by reference
number, please include the board.
DISPLAY BOARD
**************
C551
C552
C553
C958
C960
specified.
6-705-180-01 IC LC75827W
6-600-384-01 IC KSM-401E (IR)
6-705-374-01 IC MM3033DULE
< LIQUID CRYSTAL DISPLAY >
LCD501 1-805-450-11 DISPLAY PANEL, LIQUID CRYSTAL
< LED >
LED501
LED502
LED503
LED503
LED504
6-500-459-01
6-500-459-01
6-500-510-01
8-719-053-09
6-500-510-01
LED
LED
LED
LED
LED
CL-195PG-CD-T (DISC IND) (RW300)
SML-310VTT86 (DISC IND) (R3000)
CL-195PG-CD-T (2) (RW300)
LED504
LED505
LED505
LED506
LED506
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (2) (R3000)
CL-195PG-CD-T (1) (RW300)
SML-310VTT86 (1) (R3000)
CL-195PG-CD-T (SENS) (RW300)
SML-310VTT86 (SENS) (R3000)
LED507 6-500-510-01 LED CL-195PG-CD-T (ATT) (RW300)
LED507 8-719-053-09 LED SML-310VTT86 (ATT) (R3000)
LED508 6-500-510-01 LED CL-195PG-CD-T (8) (RW300)
Ref. No.
Part No.
Description
Remark
LED508
LED509
LED509
LED510
LED510
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (8) (R3000)
CL-195PG-CD-T (5) (RW300)
SML-310VTT86 (5) (R3000)
CL-195PG-CD-T (4) (RW300)
SML-310VTT86 (4) (R3000)
LED511
LED511
LED512
LED512
LED513
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
LED
LED
LED
LED
LED
CL-195PG-CD-T (3) (RW300)
SML-310VTT86 (3) (R3000)
CL-195PG-CD-T (SHUF) (RW300)
SML-310VTT86 (SHUF) (R3000)
CL-195PG-CD-T (DSPL) (RW300)
LED513
LED514
LED514
LED515
LED515
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (DSPL) (R3000)
CL-195PG-CD-T (EQ3) (RW300)
SML-310VTT86 (EQ3) (R3000)
CL-195PG-CD-T (OFF) (RW300)
SML-310VTT86 (OFF) (R3000)
LED516 6-500-510-01 LED CL-195PG-CD-T (SEEK – m .)
(RW300)
LED516 8-719-053-09 LED SML-310VTT86 (SEEK – m .)
(R3000)
LED517 6-500-510-01 LED CL-195PG-CD-T (SEEK + > M)
(RW300)
LED517 8-719-053-09 LED SML-310VTT86 (SEEK + > M)
(R3000)
LED518 6-500-510-01 LED CL-195PG-CD-T (REP) (RW300)
LED518
LED520
LED520
LED521
LED521
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (REP) (R3000)
CL-195PG-CD-T (VOLUME –) (RW300)
SML-310VTT86 (VOLUME –) (R3000)
CL-195PG-CD-T (VOLUME +) (RW300)
SML-310VTT86 (VOLUME +) (R3000)
LED522
LED522
LED524
LED524
LED525
6-500-510-01
8-719-053-09
6-500-510-01
8-719-053-09
6-500-510-01
LED
LED
LED
LED
LED
CL-195PG-CD-T (SEL) (RW300)
SML-310VTT86 (SEL) (R3000)
CL-195PG-CD-T (SOURCE) (RW300)
SML-310VTT86 (SOURCE) (R3000)
CL-195PG-CD-T (MODE) (RW300)
LED525 8-719-053-09 LED SML-310VTT86 (MODE) (R3000)
< TRANSISTOR >
Q502
8-729-038-67 TRANSISTOR KRC102S
< RESISTOR >
R501
R502
R503
R504
R505
1-216-819-11
1-216-819-11
1-216-819-11
1-216-821-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
1K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5
CDX-R3000/RW300
DISPLAY
Ref. No.
6
Part No.
Description
R506
R507
R508
R509
R510
1-216-823-11
1-216-825-11
1-216-827-11
1-216-829-11
1-218-867-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
2.2K
3.3K
4.7K
6.8K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R578
1-216-805-11 METAL CHIP
47
5%
R578
1-216-809-11 METAL CHIP
100
5%
R579
1-216-805-11 METAL CHIP
47
5%
R511
R512
R513
R514
R515
1-216-819-11
1-216-819-11
1-216-819-11
1-216-821-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
1K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R579
1-216-809-11 METAL CHIP
100
5%
R580
1-216-805-11 METAL CHIP
47
5%
R580
1-216-809-11 METAL CHIP
100
5%
R516
R517
R518
R519
R531
1-216-823-11
1-216-825-11
1-216-827-11
1-216-829-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
2.2K
3.3K
4.7K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R532
R533
R535
R536
R537
1-216-813-11
1-216-813-11
1-216-815-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220
330
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R551
R552
R553
R554
R555
1-216-825-11
1-216-815-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
330
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R556
R557
R558
R559
R560
1-216-840-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
39K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R561
R571
1-216-857-11 METAL CHIP
1-216-805-11 METAL CHIP
1M
47
5%
5%
R571
1-216-809-11 METAL CHIP
100
5%
R572
1-216-805-11 METAL CHIP
47
5%
R572
1-216-809-11 METAL CHIP
100
5%
1/10W
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
R573
1-216-805-11 METAL CHIP
47
5%
R573
1-216-809-11 METAL CHIP
100
5%
R574
1-216-805-11 METAL CHIP
47
5%
R574
1-216-809-11 METAL CHIP
100
5%
R575
1-216-805-11 METAL CHIP
47
5%
R575
1-216-809-11 METAL CHIP
100
5%
R576
1-216-805-11 METAL CHIP
47
5%
R576
1-216-809-11 METAL CHIP
100
5%
R577
1-216-805-11 METAL CHIP
47
5%
R577
1-216-809-11 METAL CHIP
100
5%
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
Ref. No.
Part No.
Description
Remark
< SWITCH >
S501
S502
S503
S504
S505
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
SWITCH, TACTILE (OFF)
SWITCH, TACTILE (SOURCE)
SWITCH, TACTILE (MODE)
S506
S507
S508
S509
S510
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
SWITCH, TACTILE (SEL)
SWITCH, TACTILE (VOLUME +)
SWITCH, TACTILE (VOLUME –)
SWITCH, TACTILE (ATT)
SWITCH, TACTILE (BTM/SENS)
S511
S512
S513
S514
S515
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
SWITCH, TACTILE (1)
SWITCH, TACTILE (2)
SWITCH, TACTILE (SEEK + > M)
SWITCH, TACTILE (SEEK – m .)
SWITCH, TACTILE (EQ3)
S516
S517
S518
S519
S520
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
1-786-763-11
SWITCH, TACTILE (DSPL)
SWITCH, TACTILE (SHUF)
SWITCH, TACTILE (6)
SWITCH, TACTILE (5)
SWITCH, TACTILE (4)
S521
S522
S523
1-786-763-11 SWITCH, TACTILE (3)
1-529-566-61 SWITCH, PUSH (1 KEY) (SHUTTER)
1-786-763-11 SWITCH, TACTILE (REP)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
1/10W
(RW300)
1/10W
(R3000)
CDX-R3000/RW300
MEMO
7
CDX-R3000/RW300
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
1.0
1.1
8
Date
2003.11
2005.07
Description of Revision
New
Change of display board. (Suffix -11 to -13)
(SPM-05009)

CDX-R3000/RW300

Transcription

Similar documents

Aiwa CDC-R504MP, CDC-X504MP Service manual. www.s

Service Manual

to the 2015 Holiday Sales Guide .

PARTS CATALOG B121/B122/B123