Bildkatalog des Onlineshops LDM

Transcription

Special offers end current prices: http://www.ldm-tuning.de
Document draw on 09.07.2012.
IFA engine
Contact breaker ZW 1103
Prod.No. 1321
9,99
Ignition contact breaker for the Barkas static engine ZW 1103. mounted at the fire fighter pump TS 8/8
and at the universal staic engine EL 308.
original spare part (NOS)
tow pieces will be needed
current collector ZW 1103
Prod.No. 7445
3,70
Pantograph for the contact breaker ignition of the Barkas static engine ZW 1103. mounted at the fire
fighter pump TS 8/8.
two pieces will be needed
Cylinder base packing ZW 1103
Prod.No.
Cylinder base packing for the Barkas static engine ZW 1103
The engine ZW 1103 is offen used by the Tragkarft-portable fire pumpe TS 8/8.
6932
17,33
6921
34,03
special sealing paper, mad in Germany
one piece will be needed
Cylinder head packing ZW 1103 and DKW ZW1101
Prod.No.
Cylinder head packing for the Barkas static engine ZW 1103 and DKW ZW1101.
The engine ZW 1103 is offen used by the Tragkarft-portable fire pumpe TS 8/8.
made in Germany
Felt arm
Prod.No. 7447
1,55
Felt wiper for oil drop of the contact breaker ignition system.
Fir to some Barkas static engine ZW 1103. mounted at the fire fighter pump TS 8/8 and at the
universal staic engine EL 308.
Ignitinon cap ZW 1103
Prod.No. 7446
0,90
Cap for the contact breaker ignition of the Barkas static engine ZW 1103. mounted at the fire fighter
pump TS 8/8.
material: aluminium
diameter: 45mm
Ignition capacitor ZW 1103
Prod.No. 7448
2,54
Capacitor for the contact breaker ignition system of the Barkas static engine ZW 1103. mounted at the
fire fighter pump TS 8/8 and at the universal staic engine EL 308.
delivery without mounting parts)
tow pieces will be needed
IFA engine > pistons
Seite 1 from178
powered by 2orange.de
Kolben EL 308
Prod.No.
140
85,00
Prod.No.
6512
198,00
Prod.No.
6513
198,00
Prod.No.
6515
189,00
Prod.No.
6516
189,00
Piston for IFA-engine EL308.
Made in Germany, original aluminium alloy, original crowned contour.
zero mark: 74,00
Please choose your piston size and write it at the winodow below.
scope of delivery:
complete with piston pin, wire snap rings and piston rings
oin blank number: 74.1 (written inside of the pistons)
Piston ZW 1103 left hand
Left piston for IFA-engine class ZW1103 two cylinder static engine.
cylinder capacity: 1100 ccm
21KW, 29PS
bore: please choose the size
Please tell us the pistion-number written inside of the pistons!
Piston ZW 1103 right hand
Right piston for IFA-engine class ZW1103 two cylinder static engine.
cylinder capacity: 1100 ccm
21KW, 29PS
bore: please choose the size
Piston 80,50 2VD 8/8 SVL plancet no. 14201
Piston for IFA-engine class 2VD 8/8 SVL two cylinder V-diesel engine.
Fit to Mulicar M22, GTP 100, UT 082, GT 124.
coin blank number: 14201 (written inside of the pistons)
10/11,5KW, 13/15PS
bore: 80,50
Piston 80,50 2VD 8/8 SVL plancet no. 1470
Piston for IFA-engine class 2VD 8/8 SVL two cylinder V-diesel engine.
Fit to Mulicar M22, GTP 100, UT 082, GT 124.
coin blank number: 1470 (written inside of the pistons)
10/11,5KW, 13/15PS
bore: 80,50
IFA-vehicles
Seite 2 from178
Bleeder screw for frontwheel brake cylinder S4000 and W50
Prod.No. 7635
0,96
Bleeder screw for the front brake cylinders of the truck S4000, S4000-1 (successor of the truck Horch
H3S) and IFA W50.
thread: M8x1,25
spanner gap: SW9
total length: 32,5 mm
thread length: 12 mm
length of the spanner gap: 4,6 mm
one piece will be needed for each wheel brake cylinder
Bleeder screw for rear wheel brake cylinder S4000 and W50
Prod.No. 7634
3,52
Bleeder screw for the rear brake cylinders of the truck S4000, S4000-1 (successor of the truck Horch
H3S) and IFA W50.
thread: M8x1,25
spanner gap: SW9
total length: 49 mm
thread length: 15 mm
length of the spanner gap: 7,6 mm
one piece will be needed for each wheel brake cylinder
Brake master cylinder, 1 circle
Prod.No. 7391
128,17
Complete in Germany overhauled brake master cylinder.
Type: Renak EH 106
Shipping only after your old brake cylinder with the mark IFA EH 106 was send to our company.
Brake master cylinder for single brake circle fit to the vehicles: Robur, Dumper, Garant K30, Picco,
Framo, Sachsenring.
piston diameter: 25,4mm
Cap sleeve for fornt wheel brake cylinder S4000 and W50
Prod.No. 7177
6,90
Cap sealing for the front wheel brake cylinder of the truck S4000, S4000-1 (successor of the truck
Horch H3S) and IFA W50.
clinder diameter: 31,8 mm (1" 1/4)
thickness: 8mm
two pieces will be needed for each wheel brake cylinder
made in Germany
Copper pipe 10x1
Prod.No. 7573
53,92
Pipes made of copper as an 5m collar.
The copper tube is an ductile, seamless streched and easy by hand bendabel.
Ideal and easy to apply for Old- and Youngtimes and lorrys as well.
Can be used for repair or complete production from scratch for fuel pipes, oel pipes or diesel pipes.
The copper material can by finished with an chrome plate after your work is done.
Material: copper
outside diamter: 10mm
inside diamter: 8mm
thickness: 1mm
length: 5m Bund
Seite 3 from178
Copper pipe 5x1
Prod.No. 7570
25,79
Material: copper
inside diamter: 3mm
thickness: 1mm
length: 5m Bund
Copper pipe 6x1
Prod.No. 7571
34,94
Material: copper
inside diamter: 4mm
thickness: 1mm
length: 5m Bund
Copper pipe 8x1
Prod.No. 7572
45,37
Material: copper
inside diamter: 6mm
thickness: 1mm
length: 5m Bund
Dust sealing for fornt wheel brake cylinder S4000 and W50
Prod.No. 7639
8,50
Dust sleeve for the front wheel brake cylinder of the truck S4000, S4000-1 (successor of the truck
clinder diameter: 31,8 mm (1" 1/4)
material: rubber, black
made in Germany
Fornt wheel brake cylinder S4000 and W50
Prod.No. 7638
49,95
Wheel brake cylinder overhauled for the front axle of the truck S4000, S4000-1 (successor of the truck Horch H3S) and IFA
W50.
The german overhauling at the wheel brake cylinders will be the best quality and equals to the first original production.
This spare part we can only delivered at direct exchange. You have to ship your worn out brake cylinder in advance to our
company.
cylinder bore: 31,8 mm
delivery complete with cap sleeves and dust sealings
case mark: FZ 5R
overhauled in Germany
Seite 4 from178
Indicator lamp complete Robur, Framo
Prod.No. 7620
15,20
Direction indicator as an complete spare part
Angular flasher lamp of the LKW Robur LO and LD as Frami as well.
Can be used for 6V,12V und 24V bulbs 21W
Colour: orange / yellow
Delivery inclusive chrome frame, lense and sealing, base plate with bulb holder, mounting plate,
rubber wire sealing and rubber sealing to the car body.
new original spare part
original no: 8580.9/1
Indicator lense Robur, Framo
Prod.No.
Lense for the angular flasher lamp of the LKW Robur LO and LD as Frami as well.
colour: orange / yellow
original no: 104-62 ORANGE
7569
4,25
Master brake cylinder S4000
Prod.No. 7657
202,94
Complete overhauled one circle master brake cylinder inklusive sleeves and brake fluid tanks for the
lorry S4000 and S4000-1.
Type: Single brake system.
The german overhauling at the master brake cylinders will be the best quality and equals to the first
original production.
This spare part we can only delivered at direct exchange. You have to ship your worn out masterbrake
cylinder in advance to our company.
delivery inclusive dust cap for pushing pin
piston diameter: 38 mm
case type: FH 107
Master brake cylinder W50, late version
Prod.No. 7656
129,30
Complete overhauled two circle master brake cylinder inklusive sleeves and brake fluid tanks for the lorry IFA W50.
Type: new version (complete bore diameter: 38mm)
The german overhauling at the master brake cylinders will be the best quality and equals to the first original production.
This spare part we can only delivered at direct exchange. You have to ship your worn out masterbrake cylinder in advance
to our company.
case type: ZM 31R
Master brake cylinder W50, old version
Prod.No. 7640
129,30
Complete overhauled two circle master brake cylinder inklusive sleeves and brake fluid tanks for the
lorry IFA W50.
Type: old version (complete bore diameter: 38mm)
The german overhauling at the master brake cylinders will be the best quality and equals to the first
This spare part we can only delivered at direct exchange. You have to ship your worn out masterbrake
case type: WJ 15a or WJ 85
Seite 5 from178
Rear wheel brake cylinder S4000 and W50
Prod.No. 7637
49,95
Wheel brake cylinder overhauled for the rear axle of the truck S4000, S4000-1 (successor of the truck
The german overhauling at the wheel brake cylinders will be the best quality and equals to the first
This spare part we can only delivered at direct exchange. You have to ship your worn out brake
cylinder bore: 38 mm
delivery complete with cap sleeves and dust sealings
case mark: FZ 25R
Ring sleeve master brake cylinder, L60
Prod.No.
7235
6,90
Prod.No.
7230
6,90
Prod.No.
7234
6,90
Ring sleeve for the master brake cylinder of the lorry IFA L60.
scope of delivery: 1 piece
made in Germany
Ring sleeve master brake cylinder, W50
Ring sleeve for the master brake cylinder of the lorry IFA W50.
made in Germany
Ring sleeve wheel brake cylinder
Ring sleeve for the wheel brake cylinder of the lorry Robur LO oder LD.
made in Germany
Sealing ring fit to brake master cylinder of ROBUR truck
Prod.No. 7175
6,90
Sealing ring with outer lip for 2-circuit brake master cylinder of ROBUR truck LO or LD (made in GDR)
Outer diameter: 32 mm (1" 1/4)
Inner diameter: 22 mm (0,866")
thickness: 5 mm (0,197")
four pieces will be needed for one brake master cylinder
made in Germany
Sealing ring set for brake master cylinder EH 107
Prod.No. 7615
17,23
Rubber sealing set consist of one outer lip ring and one cap sleeve for the single-circuit brake master
cylinder type EH 107 with hole diameter 32mm.
one kit will be needed for the brake master cylinder
made in Germany
Sleeve for rear wheel brake cylinder S4000 and W50
Prod.No. 7636
6,90
Cap sealing for the rear axle wheel brake cylinder of the truck S4000, S4000-1 (successor of the truck Horch H3S) and IFA
W50.
clinder diameter: 38 mm (1" 1/4)
thickness: 8mm
made in Germany
IFA-vehicles > Framo
Seite 6 from178
Carburettor Framo 1000ccm
Prod.No. 7029
145,00
Complete overhauled Carburettor for the three cylinder Framo engine with 1000 ccm
cylinder capacity ( Barkas V901 ). Delivery without intake pipe.
Carburettor type: H 362-12
[high quality from Germany]}
Please note, we can only exchange you this spare part if you ship 1x carburettor H 362-12 to our
company in advance!
Ring sleeve, for wheel brake cylinder, Framo ( incl. 2 pieces )
Prod.No.
7045
5,71
Prod.No.
One row grooved ball bearing 16013, it fit in a gearbox from the P70.
The bearing can be only used at the latest model of P70 with dry clutch system.
7158
14,45
Prod.No.
7155
8,84
Prod.No.
7156
28,50
Prod.No.
7157
18,57
Prod.No.
7348
350,00
Ring sleeve, for the wheel brake cylinder for Framo (Barkas V901)
Comlete set for one wheel brake cylinder (incl. 2 pieces)
fit to brake cylinder diameter 25,35mm
One set will be needed for each wheel side rear
IFA-vehicles > P70 / F8 / F9
Grooved ball bearing 16013 small
mark: 16013
1x groved ball bearings will be needed
widness: 11mm
Grooved ball bearing, 6206 C2
One row grooved ball bearing 6206 C2, bearing for P70 and F8 gearbox.
Type P70 with and without dry clutch.
made in Germany
Grooved ball bearing, 6207
One row grooved ball bearing 6207, bearing for P70 and F8 gearbox.
made in Germany
Grooved ball bearing, 6305
One row grooved ball bearing 6305, bearing for P70 and F8 gearbox.
made in Germany
Piston P70, IFA F8
Piston set for the P70 and F8 consist of:
1x piston left hand
1x piston right hand
2x piston pin dimeter: 15mm
4x piston pin clips
piston number:76.001.1 (left) 76002.1 (right)
made in Germany
one kit will be needed
Seite 7 from178
Radial sealing D20 x 35 x 10
Prod.No.
7160
6,62
Prod.No.
7162
10,33
Prod.No.
7159
8,95
Prod.No.
7161
24,89
Prod.No.
6920
5,71
Prod.No.
7145
14,68
Radial sealing for the P70 and F8 gearbox.
made in Germany
fit to gearbox of F8 and P70 with and without dry clutch system
Radial sealing for the P70 and F8 rear axle.
Outside with metal ring.
made in Germany
Radial sealing for the P70 and F8 gearbox.
made in Germany
fit to gearbox of F8 and P70 with and without dry clutch system
Radial sealing for the P70 gearbox.
Outside with metal ring.
made in Germany
fit to gearbox of P70 with dry clutch system
Ring sleeve, for wheel brake cylinder, front axle (IFA F9)
Ring sleeve, for one front wheel brake cylinder.
fit to brake cylinder diameter 25,mm (1")
One set will be needed for each wheel side of front axle
IFA-vehicles > Trabant 500/600
Bulbs spare kit R2 / 6V
Spare kit with different bulbs fit to voltage of 12V
content:
1x R2-lamp 45/40W with base P45t
1x spherical lamps 18W white with base Ba15s
1x tubular lamp 18W (C21W) with base SV 8,5
1x bulb 4W (T4W) with base BA 9s
1x bulb for speedometer 0,6W with base BA 7s
1x Torpedo-fuse 8A
1x Torpedo-fuse 16A
Seite 8 from178
Chromium-plated ring for front direction indicator lamp (P50/P60)
Prod.No.
New produced chromed ring for old front flash lights of Trabant 500 and 600 (P50/60).
7249
13,25
Direction indicator lamp front, complete (P50/P60)
7356
51,23
Prod.No.
New produced frot flasher for the Trabant 500 and 600 (P50/60).
Set consits of:
1x Indicator glass, orange
1x bulb carrier
1x seal for fasher
1x chrome front rim
made in Germany
Glass for front direction indicator lamp, white
Prod.No. 7248
15,40
New produced spare glass for old front flash lights of Trabant 500 and 600 (P50/60)and fit to Wartburg
311,312,313 and Framo.
Colour: colorless transparent
with stuck on sealing rubber
high quality, made in Germany
in tandem with chromed ring it can be used also as position light fit to camper Intercamp
Glass for front direction indicator lamp, yellow (P50/P60)
Prod.No. 7247
15,40
New produced spare glass for old front flash lights of Trabant 500 and 600 (P50/60)and fit to Wartburg
311,312,313 und Framo.
Colour: orange transparent
with stuck on sealing rubber
high quality, made in Germany
Prod.No. 7250
Rubber sealing cap for front direction indicator lamp (P50/P60/B1000/Multicar)
9,33
New produced sealing cap fit to old front flasher lights of Trabant 500 and 600 (P50/60), Barkas
B1000 and Multicar truck and fit to Wartburg 311,312,313 and Framo, and fit to the side lights of the
camp trailer INTERCAMP.
Telescopic shock absorber P50
Prod.No.
Directional pressure telescopic shock absorber for leaf spring. Fit to front and rear axle of Trabant 500, 600.
scope of delivery:
7086
34,67
6994
7,50
complete inclusive bushing, lower bushing diameter 8mm
Made in Germany
IFA-vehicles > Trabant 500/600 > brake system
toothed segment for lever for parking brake
Prod.No.
toothed segment for the handbrake lever of the Trabant 500,600,601 and 1.1
delivery without connection rivet
original spare part
IFA-vehicles > Trabant 500/600 > Rubber sections & -parts
Seite 9 from178
Profile filler windscreen
Prod.No. 6899
18,00
profile filler for rubber section windscreen (Limousine and Universal (station wagon)) and rear window
(only Limousine) fit to Trabant 500 (P50), 600 (P60) and early Trabant 601
available in three different colours: black, white and grey (Please chose the wanted colour below!).
Length 3,60 meter
Rubber for rear light, colour: black (P50,P60)
Prod.No.
6640
18,50
Prod.No.
6691
18,50
Prod.No.
6755
2,94
6754
2,94
Seal for the rear light cases. Fit to Trabant 500/ 600 car boot Limousine.
material: rubber
colour: black
Rubber for rear light, colour: grey (P50,P60)
Seal for the rear light cases. Fit to Trabant 500/ 600 car boot Limousine.
material: rubber
colour: black
rubber pad for 20 mm mouldings (yard goods)
Rubber pad for aluminium mouldings with a wide of 20 mm.
the price is for one meter of rubber pad (ordering two pieces means one piece of 2 meter)
material: rubber
colour: black
rubber pad for moulding (yard goods)
Prod.No.
Rubber pad for aluminium moulding with a wide of 12 mm.
the price is for one meter of rubber pad (ordering two pieces means one piece of 2 meter)
material: rubber
colour: black
rubber pad for plane frame
Prod.No. 6753
5,20
The rubber is mounted between door sheet metal of door frame and lower aluminium sections of plane
frame.
Fit to Trabant 500/ 600.
material: rubber
colour: black
length: 1 m
width (without edge): 35 mm
thickness: 1,5 mm
Rubber section for rear boot Limousine
Prod.No.
Black cellular rubber (sponge rubber) section for car boot of Trabant 500 / 600.
7182
19,79
length: 3,50 Meter
German product
Seite 10 from178
Rubber-section for inner door sealing (P50/60)
Prod.No. 6747
9,00
rubber-section for inner door sealing at B-pillar (and perhaps A-pillar (length about 0.6 to 0.65 Meter),
too) of Trabant 500 and 600 (all variants)
At the upper part of B-pillar is an additional sheet metall to clamp the flat part of rubber. In the lower
part of B-pillar the rubber-section will be clamped between b-pillar and outside cladding.
Also fit to lower sealing between A-pillar and B-pillar, mounted with an additional L-section (length one
Meter for each door).
length: 1 m
material: rubber
colour: black
length of flat part (lug): ca. 16 mm
outer diamter of hose: ca. 15 mm
Rubber-section for inner door sealing, black (P50/60)
Prod.No. 6750
27,50
Black cellular rubber-section for side door sealing of Trabant 500 and 600 (all variants).
The rubber seals starting at the lower end along the A-pillar under the roof frame to lower end of
B-pillar, but it will not mount inside the car body.
length: 4 m
material: cellular rubber
colour: black
Rubber-section for inner door sealing, grey (P50/60)
Prod.No. 6847
27,50
Black cellular rubber-section for side door sealing of Trabant 500 and 600 (all variants).
The rubber seals starting at the lower end along the A-pillar under the roof frame to lower end of
B-pillar, but it will not mount inside the car body.
length: 4 m
material: cellular rubber
colour: grey
Rubber-section for integral pane (median web) in side doors (P50/60)Prod.No.
6749
5,97
Rubber-section for front sealing of integral pane of each side door of Trabant 500 and 600 (all
variants).
This rubber-section will be used for sealing the front side of pane (median web).
The lengthened rubber lip seals the opening between median web and sliding pane.
length: 0,5 m (fit to one door)
material: rubber
colour: black
Rubber-section for integral pane in side doors (P50/60)
Prod.No. 6748
9,00
rubber-section for integral pane of side doors of Trabant 500 and 600 (all variants).
This rubber-section will be used for sealing the upper, lower and outer side of each pane. For sealing
the inner side (median web) a different rubber-section is neccessary.
length: 1 m (fit to one door)
material: rubber
colour: black
Rubber-section for integral pane in side doors (P50/60)
Prod.No. 6900
10,89
rubber-section for sliding window of side doors of Trabant 500 and 600 (all variants).
This rubber-section will be used for outer sealing the lower side and along the window frame from
lower corner (front) up to median web.
length: 1,5 m (fit to one door)
material: rubber
colour: black
Seite 11 from178
Rubber-section for window guiding
Prod.No.
6901
19,98
Rubber section for door sliding window sealing. Material: rubber with plush.
width of the rubber section: 12mm
glas width: 5mm
length: 2,20 Meter (0,8 Meter for horizontal sealing + 1,4 Meter along the upper window frame
for each door, one piece will be needed
Rubber-section for windscreen and for rear window (P50/60)
Prod.No.
6745
28,33
Prod.No.
6639
14,30
Prod.No. 6638
The rubber is mounted behind the trademark at the engine bonnet. Fit to Trabant 500/ 600.
8,50
rubber-section for windscreen of Trabant 500 and 600 (all variants)
and for rear window (only for car body variant Limousine)
For installation this rubber-section an additional profil filler is necessary.
length: 3,00 m
material: rubber
colour: black
necessary accessory: profile filler (obtainable in different colours)
Seal for hinge
Rubber for the hinge of the engine bonnet. Fit to Trabant 500/ 600.
one set consist of two pieces
material: rubber
colour: black
2 sets will be needed
Seal for lettering
material: rubber
colour: black
sealing rubber for door-opener left hand
Prod.No.
6838
12,74
Prod.No.
6752
12,74
The rubber is mounted between door-plating and door-opener unit.
material: rubber
colour: black
left side, driver side and rear door
Limousine: one piece
station wagon: two pieces
sealing rubber for door-opener right hand
The rubber is mounted between door-plating and door-opener unit.
material: rubber
colour: black
right side, codriver side
Limousine or station wagon: one piece
Sealing rubber numberplate lights
Prod.No. 6637
27,00
The rubber is mounted behind the metal profile for the number plate lights. Fit to Trabant 500/ 600 car
boot Limousine.
material: rubber
colour: black
IFA-vehicles > Trabant 500/600 > Front axle
Seite 12 from178
Bushing for king pin T500 / T600 / T601
Prod.No. 7607
14,25
Original Pressstoff-bushing for guiding of the lower bearing of the front axle at the Trabant 500,600
and 601 with vintage limit.
Original spare part.
The bushing have to be reamed by reamer after press-in operation.
material: fibre bonded plastic
colour green
up to vintage: 31.3.1968 for Trabant 601
made in Germany
Lower bushing for spring yoke T500 / T600 / T601
Prod.No. 7606
10,40
Original Pressstoff-bushing for guiding of the spring yoke at the Trabant 500,600 and 601 with vintage
limit.
colour green
made in Germany
Upper bushing for spring yoke T500 / T600 / T601
Prod.No. 7605
11,40
Original Pressstoff-bushing for guiding of the spring yoke at the Trabant 500,600 and 601 with vintage
limit.
colour green
made in Germany
IFA-vehicles > Trabant 500/600 > Ignition system
IFA-vehicles > Wartburg 311 / 312 / 313
Cylindrical roller for freewheel 12x12
Prod.No. 3145
2,65
Single part of the cylindrical roller for the freewheel of the Wartburg 311 (from frame number: 637057
ownwards)
10 pieces will be needed
zero mark: diameter 12,00mm
length: 12mm
made in Germany
Prod.No.
Single part of the cylindrical roller for the freewheel of the Wartburg 311 (up to frame number: 637057)
7394
2,95
length: 18mm
made in Germany
Seite 13 from178
Joint for trak rod W311, left-hand thread
Prod.No.
6592
36,50
Prod.No.
6603
36,50
Prod.No. 6735
Rubber button pad for engine bonnet of old car body variant of Wartburg (typ 311, 312, 313)
1,95
Trak rod end with eleastomer bearing. Fit to Wartburg 311.
Shank type with lef hand thread M14 x 1,5.
original spare part
lock nut: trak rod nut
Castel nut: slotted nut M12 x 1,5
pint: split pin
Joint for trak rod W311, right-hand thread
Trak rod end with eleastomer bearing. Fit to Wartburg 311.
Shank type with right hand thread M14 x 1,5.
original spare part
lock nut: trak rod nut
Castel nut: slotted nut M12 x 1,5
pint: split pin
Rubber button pad for engine bonnet (W311)
diameter of rubber pad: 20 mm
thickness of rubber pad: ca 5 mm
length total: ca 21 mm
diameter of mounting rubber pin (without cone): ca 5,5 mm
biggest diamter of cone: ca 9 mm
Shaft seal gearbox
Prod.No.
6939
8,50
Prod.No.
6599
29,50
Prod.No.
7681
6,50
Prod.No.
6815
195,00
Oil seal for the Wartburg 311 gearbox.
material: NBR
size: 32 x 50 x 7
type without additional dust lip
Sleeve rubber final drive (W311)
Rubber sleeve for Wartburg 311 outer joint universal drive shaft.
Sleeve rubber for central lubrication (W311)
Rubber sleeve for central lubrication system Wartburg 311.
material: Gummi
original spare parts
Starter 6V
Starter for 6V vehicles.
Fit to the fallowing cars: Wartburg 311, 312, Framo und IFA F9
your old starter have to be first shipped to our company for exchange
IFA-vehicles > Wartburg 311 / 312 / 313 > Brake system
Seite 14 from178
Brake hose, front and rear axle
Prod.No.
6769
8,48
Prod.No.
7168
4,43
Prod.No.
Sealing ring for wheel brake cylinder, front axle W311 (1 pair = 2 pieces)
6012
8,73
7176
19,50
Flexible brake hose for the Wartburg 311 drum brake.
total length: 49 cm
tap: 1x M12 x 1,5 core thread and 1x M12 x 1,5 male thread
for the front axle two pieces will be needed and one for the rear axle
retainer for brake hose
Brake hose retainer for Wartburg 311
to put into the circumferential slot of the brake hose fitting
fit or all types of W311
for one vehicle you need four pieces
slot wide: 14 mm
thickness: 1,75 mm
Two sealing rings for the wheel brake cylinders built in front brake of Wartburg 311.
for diameter of piston: 27 mm
scope of delivery: two piece of ring sleeve
one piece is needed for each wheel brake cylinder
first-class quality made in Germany
Sleeve set for brake master cylinder (1-circuit) Ø 25,4mm = 1
Prod.No.
Two sealing rings for the wheel brake cylinders built in front brake of Wartburg 311.
for diameter of piston: 25,4 mm
wheel brake cylinder front axle, left, W311
Prod.No. 6011
32,50
Complete in Germany overhauled wheel brake cylinder.
Type: RENAK CZ 25
Shipping only after your old brake cylinder with the mark RENAK CZ 25 was send to our company.
Wheel brake cylinder for Wartburg 311 front, brake system drum brake.
scope of delivery:
complete with ring sleeves and piston
without bleeder screw
brake-piston D= 27mm
brake line connection with thread M12x1
NOT fit to brake system of Multicar M24
Please note, we can only exchange you this spare part if you ship 1x wheel brake cylinder with the
mark CZ 25 to our company in advance!
Seite 15 from178
wheel brake cylinder front axle, right, W311
Prod.No. 6010
32,50
Type: RENAK CZ 25
scope of delivery:
Wheel brake cylinder rear, original
Prod.No. 7252
35,39
Complete in Germany overhauled rear wheel brake cylinder with cap sleeves, brak-piston
D=25,35mm.
Mark: IFA BHL
Fit to Wartburg 311
scope of delivery: inclusive cap sleeves and bleeder screw
break piston diameter: 25,35mm
also used for some IFA-vehicles
mark Renak IFA BHL to our company in advance!
IFA-vehicles > Wartburg 311 / 312 / 313 > Cooling system
Coolant hose (310nmm) 3-way coolant petcock (W311)
Prod.No.
6913
5,82
Prod.No.
6914
8,94
Prod.No.
6936
17,92
coolant hose fit to both sideway tubes of 3-way coolant petcock
lenght: 310mm (12,2")
Coolant hose (480mm) for sideway tubes of distributor (W311)
coolant hose fit to both sideway tubes of distributor
lenght: 480mm (18,9")
Coolant hose, 15 x 3,5mm (yard goods)
rubber coolant hose with textile inset (DIN 73411 7/79)
up to 6 bar
Inner diameter: 15 mm (0,59 inch)
Thickness of wall: 3,5 mm (0,138 inch)
up to 125°C
Outer layer (EPDM): resistance to oil, ozone and aging through heat
Inner layer (EPDM): resistance to antifreeze admixture and corrosion inhibitor
Deliverable as yard goods. If order two pieces of this article we will deliver one piece with a length of
two Meter.
Coolant hose, 195mm, distributor-water pump (W311)
Prod.No.
6912
7,09
Coolent hose fit to connect the distributor with water pump
length: 195mm (7,68")
Seite 16 from178
Coolant hose, 25 x 3,5mm (1 Meter)
Prod.No.
6948
14,77
Prod.No.
6917
29,86
Prod.No.
Short piece of coolant hose to connect the lower pipe of radiator with middle connection pipe of distributor
6916
2,18
Prod.No.
6911
2,72
Prod.No.
6597
10,40
Prod.No.
7490
16,70
Prod.No.
7491
13,70
rubber coolant hose with textile inset (DIN 73411 issue 1955)
working pressure: 3 bar
Inner diameter: 25 mm (1 inch)
Outer and inner layer made of black SBR-rubber quality
resistant against hot water with antifreeze admixture from -20°C up to +95°C
Only obtainable in pieces of one Meter.
Rubber coolant hose with textile inset (DIN 73411 7/79)
bup to 6 bar
up to 125°C
Coolant hose, 60mm radiator-distributor (W311)
lenght: 60mm (2,36")
Coolant hose, 75mm, radiator-thermostat (W311)
Short piece of coolant hose to connect the upper pipe of radiator with thermostat
lenght: 75mm (2,95")
radiator end cap W311, Framo
zinc-coated end cap (seal) fit to radiator of Wartburg 311 and Framo
with additional pressed-on aluminium cover
diameter of aluminium cover with knurling: 100 mm
inner parts of seal cap made of zinc-coated sheet metall and brass
with rubber sealing (diamter about 48mm)
Radiator end cap, crome, W311, Framo
Crome-coated end cap (seal) fit to radiator of Wartburg 311 and for Framo.
Type without tongue.
diameter of chrome-coated cap with knurling: 72mm
inner parts of seal cap made of brass
Radiator end cap, crome, W311, Framo
Zinc-coated end cap (seal) fit to radiator of Wartburg 311 and for Framo.
Type without tongue.
diameter of zinc-coated cap with knurling: 72mm
Seite 17 from178
Radiator end cap, crome, with strap, W311, Framo
Prod.No.
7489
16,70
Prod.No.
6586
13,70
Prod.No.
6588
9,30
Crome-coated end cap (seal) fit to radiator of Wartburg 311 and for Framo.
Type inclusive tongue to fix an small retainer cain.
diameter of chrome-coated cap with knurling: 72mm
Radiator end cap, zinc, with strap, W311, Framo
Zinc-coated end cap (seal) fit to radiator of Wartburg 311 and for Framo.
Type inclusive tongue to fix an small retainer cain.
diameter of zinc-coated cap with knurling: 72mm
radiator flange W311, Framo
brass-fitting to solder on radiator
fit to Wartburg 311 and Framo
inner diameter (solder side): 40 mm
outer diamter (side of cap): 69 mm
height: 23 mm
IFA-vehicles > Wartburg 311 / 312 / 313 > Engine
Bearing fan shaft
Prod.No. 7507
9,86
One row roller bearing for the fan shaft thrue the cylinder head of the 900 ccm and 1000ccm 3-cylinder two stroke engines.
It fit to Wartburg 311, 312 Framo, DKW and motor boates.
made by FAG
both sides ar metall covered
tow piece will be needed
Carburettor W311 1000ccm
Prod.No. 7030
145,00
Complete overhauled Carburettor for the three cylinder Wartburg 311 engine with 1000 ccm
cylinder capacity. delivery without intake pipe.
Carburettor type: H 362-24
Please note, we can only exchange you this spare part if you ship 1x carburettor H 362-24 to our
company in advance!
crankshaft 1000ccm
Prod.No. 6995
550,00
Complete overhauled crank shaft for the models Wartburg 311, 312 engines, Framo with V-pully
without anti-vibration damper (mounting nut SW46)
Crankshaft sealings are modificated to piston ring sealing pully- and fly wheel side.
with standard version of conrod
delivery iclusive needle bearings for the piston pins diameter: 20mm
good qualitiy, made in Germany
Please note, we can only exchange you this spare part if you ship 1x used crank shaft and 1x V-pully
to our company in advance!
Seite 18 from178
crankshaft 900ccm
Prod.No. 7009
990,00
Complete overhauled crank shaft for the models Wartburg 311, 312 engines, Framo with V-pully
Crankshaft sealings are modificated to piston ring sealing at the fly wheel side.
The old type of labyrinth seal is modificated to pistion ring seal.
delivery iclusive bronze bearings for the piston pins diameter: 18mm
high qualitiy, made in Germany
Please note, we can only exchange you this spare part if you ship 1x used crank shaft to our company
in advance!
Cylinder head packing 900 ccm - 12 bolts
Prod.No. 6789
59,50
Head packing for the 900 ccm, 3-cylinder two stroke engine.
Material consist of paper seal with dry graphite.
It fit to Wartburg 311, 312 Framo, DKW and motor boate with 0,9 Liter swept volume and 12 bolts for
cylinder head mounting.
made in Germany
inner diameter cylinder: 72 mm
thickness: 1,2mm
Cylinder head packing 900 ccm - 12 bolts with metal ring
Prod.No. 6788
71,50
Head packing for the 900 ccm, 3-cylinder two stroke engine.
Material consist of paper seal with dry graphite and matal ring.
It fit to Wartburg 311, 312 Framo, DKW and motor boate with 0,9 Liter swept volume and 12 bolts for
cylinder head mounting.
made in Germany
inner diameter cylinder: 72 mm
thickness: 2,2mm
Ignition distributor cover IFA F9 Framo
Prod.No.
7043
36,00
Prod.No.
7124
1,25
Prod.No.
Paper sealing for the case of the float Carburettor for Wartburg 311 and Framo.
Carburettor type: H 362-24 and Carburettor type: H 362-12
[high quality made in Germany]}
7541
2,34
Ignition distributor cover for the car models IFA F9 und Framo.
Sealing ( carburettor-flange )
Paper sealing between Carburettor suction pipe.
Carburettor type: H 362-24 and Carburettor type: H 362-12
Sealing carburettor-case
Seite 19 from178
Self-aligning bearings fan shaft
Prod.No.
Bearing for the fan shaft thrue the cylinder head of the 900 ccm 3-cylinder two stroke engines (old version)
It fit to Wartburg 311, 312 Framo, DKW and motor boates.
7508
34,90
made by FAG
both sides with sealings
tow piece will be needed
V-belt 13x1030
Prod.No. 7505
16,80
V-Belt for the models Wartburg 311, 312 engines and Framo with V-pully without anti-vibration damper (mounting nut
SW46 at the v-pully)
widness: 13mm
length: 1030mm
best qualitiy, made in Germany
V-belt 13x1060
Prod.No. 7506
16,80
V-Belt for the models Wartburg 311, 312 engines and Framo with V-pully without anti-vibration damper
(mounting nut SW46 at the v-pully)
widness: 13mm
length: 1060mm
best qualitiy, made in Germany
V-pully wheel for crank shaft 1000ccm
Prod.No. 7000
86,67
Modificated v-pully wheel for crankshaft for the models Wartburg 311, 312 engines, Framo with V-pully
Please note, we can only exchange you this spare part if you ship 1x V-pully to our company in
advance!
IFA-vehicles > Wartburg 311 / 312 / 313 > Shock absorber / axle
Radial sealing W311/ 313, front axle
Prod.No.
7594
14,70
Prod.No.
7215
11,48
Rubber sealing for the wheel hub of the front axle.
Type like original with metal ring outside.
Fit to Wartburg 311 and 313 typs: Limousine Tourist, Camping, Sport.
material: NBR
made in Germany
Radial sealing W311/ 313, rear axle
Rubber sealing for the wheel hub of the rear axle.
Type like original with metal ring outside.
material: NBR
made in Germany
Seite 20 from178
Telescopic shock absorber, W311, front axle
Prod.No. 6575
38,40
Buffer for the Wartburg 311 front axle with leaf spring. Fit to both typs: Limousine and
Tourist.
scope of delivery inclusive bushing
made in Germany
Telescopic shock absorber, W311, rear axle
Prod.No. 6574
38,40
Buffer for the Wartburg 311 rear axle with leaf spring. Fit to both typs: Limousine and
Tourist.
made in Germany
Wheel bearing outer side, front axle W311/ 313
Prod.No.
Ball bearing type: 6306 C2 mounting place at for the inner and out side of front axle.
7593
15,49
type: without cover
made in Germany
for each car front axle 4 pieces will be needed
Wheel bearing outer side, rear axle W311/ 313
Prod.No. 7213
11,33
Wheel bearing type: 6205 C2 for the outer side of the rear axle. Fit to Wartburg 311 and 313 typs:
Limousine Tourist, Camping, Sport.
made in Germany
Wheel bearing outer side, rear axle W311/ 313
Prod.No.
7214
15,49
Ball bearing type: 6306 C2 mounting place at for the inner side of rear axle.
type: without cover
made in Germany
for each car rear axle 2 pieces will be needed
IFA-vehicles > Multicar M22
Clutch cylinder gearbox side
Prod.No. 7527
57,40
Overhauled clutch cylinder for the Multicar M22. Fit to all two stroke models with hydraulic clutch
system.
Please note, we can only exchange you this spare part if you ship 1x Cluch cylinder type BH7 to our
company in advance!
genuine spare part
Protection bellows for pressure bar input clutch master cylinder
Seite 21 from178
Prod.No.
7520
3,95
release spring for brake shoes, long
Prod.No.
7197
3,18
Prod.No.
7198
2,94
long version of release spring for break shoes
release spring for brake shoes, short (M22)
short version of release spring for break shoes
Ring eye D10mm with pipe bend
Prod.No. 7516
3,29
Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection
hoses.
Can be used for banjo screws D= 10mm
Eye diameter: 10mm
diameter pipe connection: 6mm
pipe bend: 90 degree
pipe length total: 55mm
Ring eye D10mm, connection 6mm hose
Prod.No. 7537
2,48
hoses.
Eye diameter: 10mm
Prod.No. 7538
2,48
hoses.
Eye diameter: 10mm
Ring eye D12mm with pipe bend
Prod.No. 7517
3,59
hoses.
Eye diameter: 12mm
pipe bend: 90 degree
pipe length total: 74mm
Prod.No. 7539
2,49
hoses.
Eye diameter: 12mm
Seite 22 from178
Prod.No. 7540
2,49
hoses.
Eye diameter: 12mm
Rubber lining for brake and clutch pedal-shaft
Prod.No.
7519
3,50
Prod.No.
Sealing ring for wheel brake cylinder, front axle M22 (1 pair = 2 pieces)
7386
8,73
made in EU
Two sealing rings for the wheel brake cylinders built in front brake of Multicar M22.
for diameter of piston: 27 mm
Sleeve for clutch cylinder gearbox side (M22)
Prod.No. 7528
4,50
Ring sleeve for the clutch cylinder release fork of the Multicar M22. Fit to all two stroke models with hydraulic clutch
system.
made in Germany
genuine spare part
one set will be needed
Sliding piece for rear brake shoe (M22)
Prod.No.
7199
9,87
Prod.No.
7216
179,00
Sliding piece for rear brake shoe Multicar M22
two pieces for each wheel side
Starter for Multicar M20/M22
Starter fit to the following cars: Multicar M20, M22 and LO
Also fit to IFA-engine 2KVD8
wheel brake cylinder front axle, left, M22
Prod.No. 7384
32,50
Fit to Multicar M22 front axle left hand
Type: RENAK CZ 25
scope of delivery:
Seite 23 from178
wheel brake cylinder front axle, right, M22
Prod.No. 7385
32,50
Fit to Multicar M22 front axle right hand.
Type: RENAK CZ 25
scope of delivery:
Wheel brake cylinder, rear (M22)
Prod.No.
7196
29,64
Wheel brake cylinder for the raer axle of Multicar M22
one piece for each wheel side
made in EU
Wheel brake cylinder, rear, M22, original
Prod.No. 7231
35,39
Complete in Germany overhauled rear wheel brake cylinder with ring sleeves, fit to the rear axle of the
Multicar M22.
Mark: RENAK BZ
scope of delivery: inclusive ring sleeves and bleeder screw
mark Renak BZ 105 to our company in advance!
Starter for Multicar M24
Prod.No.
7217
179,00
Prod.No.
215
0,35
Starter fit to the following cars: Multicar M24
Also fit to IFA-engine 4KVD8,8/8,5
IFA-vehicles > Multicar M24 > Axle
IFA-vehicles > Multicar M24 > Brake system
Bleeder screw cap
fit to all offered bleeder screws
Protect the bleeder screw hole from dust and water.
material: rubber
made in Germany
Seite 24 from178
Distributor for brake lines M24, M25
Prod.No. 7274
7,73
Terminal block for the brake fluid with three ports to connect the brake tubes or brake pipes. Fit to the
cars Mulicar M24 and M25.
material: brass
thread : M12 X 1
mounting-diameter: 8,4 mm
Holder for brake hose
Prod.No.
6037
4,73
Brake hose retainer for Multicar M22, M24, M25
slot wide: 14 mm
thickness: 1,75 mm
pipe-connector
Prod.No. 7275
Brake tube merger for the connection of two brake tubes with flange type E and thread M12x1mm
3,61
material: steel, galvanized
thread: M12 X 1
lenght: 29mm
made in Germany
IFA-vehicles > Multicar M24 > Engine - Gear box
Brake hose front axle for Multicar
Prod.No.
7518
9,48
Prod.No.
Wheel brake hose for the rear brake system of the Multicar type M22, M24, M25.
Connection hose between the brake pipe and the wheel brake cylinder rear axle.
7641
8,50
7096
32,22
Wheel brake hose for the front brake system of the Multicar type M22, M24, M25.
Connection hose between the brake pipe and the wheel brake cylinder front right or left axle side.
total lenght: 51cm
thread: 1x M12 x 1,5 core thread
1x M12 x 1,5 male thread
delivery as an single part
made in EU
for one vehicle two pieces will be needed
Brake hose rear, fit to Multicar
total lenght: 51cm
thread: M12x1, both ends as male type
made in EU
for one vehicle two pieces will be needed
Brake shoe, complete, with lining ( front ), Multicar M25
Prod.No.
The brake shoes set fit to the frontaxle and to the rear axle of the Multicar type M25.
Set consist of:
4 pieces of breake shoe with long lining
made in EU
for each axle, one set will be needed
Seite 25 from178
Fuel pump for Multicar M25
Prod.No.
7679
83,04
Prod.No.
7218
195,00
Prod.No.
Brake cylinder can be used for the front wheel brake system of the Multicar type M25.
The wheel brake cylinders fit to the brakes of the right and left front axle.
7585
30,81
7586
30,81
Prod.No.
7670
76,89
Prod.No.
7268
76,89
Mechanical fuel pump for the engine of the Multicar type M25.
delivery as an complete unit, inclusive connection screws
made in EU
Starter for Multicar M25
Starter fit to the following cars: Multicar M25
power: 2,2kW (3,0 hp)
Wheel brake cylinder front, fit to Multicar M25
delivery as an single part inclusive bleeder screw
made in EU
for one vehicle four pieces will be needed
Wheel brake cylinder rear, fit to Multicar M25
Prod.No.
Brake cylinder can be used for the rear wheel brake system of the Multicar type M25.
The wheel brake cylinders fit to the brakes of the right and left rear axle.
made in EU
for one vehicle four pieces will be needed
IFA-vehicles > Multicar M25 > Axle
Telescopic shock absorber front axle *M25* eye-eye
Telescopic shock absorber for the front axle of the Multicar M25.
Type of model with eye and eye.
scope of delivery:
complete inclusive bushing
Made in Germany
Telescopic shock absorber front axle *M25* eye-pin
Telescopic shock absorber for the front axle of the Multicar M25.
Type´of model year 91 with eye and pin.
scope of delivery:
Made in Germany
IFA-vehicles > Multicar M25 > Brake system
Seite 26 from178
Dual brake master cylinder for Multicar M25
Prod.No.
Dual brake master cylinder used in mini truck Multicar M25 and 2t-trailer fit to Multicar.
7633
94,33
new production made in Europe
Sleeve kit dual brake master cylinder Ø 28mm (1,1?) , original, M25 Prod.No.
7236
19,50
Sleeve set to repair the dual brake master cylinder used in mini truck Multicar M25 and 2t-trailer fit to
Multicar.
complete set with:
4x sealing rings with outer lip
2x flat rubber valves
2x conical rubber valves
4x copper sealing rings
made in Germany
Sleeve set dual brake master cylinder Ø 25,4mm (1?) , original, M25Prod.No.
7187
19,50
Prod.No.
7186
12,40
Prod.No.
7192
11,87
Prod.No.
3014
37,76
Sleeve set dual brake master cylinder, Multicar M25
complete set
made in Germany
Sleeve set dual brake master cylinder, complete, M25 Ø 25,4mm
Sleeve set dual brake master cylinder, Multicar M25
complete set
made in EU
IFA-vehicles > Multicar M25 > Engine - Gear box
Thermostat
Cooling water heat governor fit to all Multicar type M25
incl. sealing ring
Thermostat opens by 82°C
Wartburg 353
Wartburg 353 > Spare parts
Wartburg 353 > Spare parts > Exhaust system
Connection pipe
Exhaust connection pipe for Wartburg 353 with 2 stroke engine.
length: 2 meter
made in EU
Seite 27 from178
Connection pipe *stainless steel*
Prod.No.
6832
56,00
Prod.No.
3018
59,67
High-grade steel exhaust connection pipe for Wartburg 353 with 2 stroke engine.
Straight connection between mainsilencer and muffler.
length: 2 meter
made in Germany
Exhaust aftermuffler W353
Exhaust aftermuffler for Wartburg 353 (two stroke)
fit to all models
made in Europe
Exhaust manifold seal
Prod.No. 3011
2,89
Paper seal with dry graphite. It fit to all Wartburg 353, 312, 311 and B-1000 with 3-cylinder two stroke
engine.
very good quality of material and with good dimension accuracy
without metall ring
inner diameter: 43 mm (1,693 inch)
three pieces will be needed
made in Germany (only available by LDM-Tuning)
Exhaust manifold seal with metall ring
Prod.No. 6706
5,99
Paper seal with dry graphite. It fit to all Wartburg 353, 312, 311 and B-1000 with 3-cylinder two stroke
engine. Usefull for all tuning engines for example RS 1000, Leutert.
brilliant quality with metall ring
inner diameter: 45 mm
made in Germany
Muffler with pipe W353
Prod.No.
3013
26,54
Prod.No.
3012
69,50
Prod.No.
3017
2,99
Prod.No.
3016
2,99
Exhaust muffler for Wartburg 353 two-stroke
made in EU
Pre expansion chamber W353
Exhaust pre silencer fit to all kind of Wartburg 353 models
made in Europe
Retainer, round, hooked
Exhaust retainer for Wartburg 353 muffler
Retainer, round, straight
Exhaust retainer for aftermuffler wartburg 353
Seite 28 from178
screw for Exhaust manifold (connection with pre silencer)
Prod.No.
6293
2,32
hexagon head screw M10 x 50
Delivery complete with nut, strength class 10.9
Wartburg 353: two pieces will be needed
Barkas B1000: three pieces will be needed
Wartburg 353 > Spare parts > Brakes
Brake master cylinder, 1 circle (+80? pledge)
Prod.No. 7097
128,17
Brake master cylinder, 1 circle for Warburg 312,313,353 (old type with brake drum system front and
rear axle)
Prod.No.
3091
114,80
fit to all Wartburg variant with 2-circle brake master cylinder.
made in EU
Brake master cylinder, two circle, original
Prod.No. 7220
90,13
Type: IFA BHL ZE 30R
Shipping only after your old brake cylinder with the mark IFA BH1 was send to our company.
The 2-circle brake master cylinder was mounted at the Wartburg 353 and 1,3
it is a brake system with two separate brake circle. One supply the front wheel brakes and one the rear
wheel brake cylinders.
The connection for the both front brake tube line is in driving direction at the front end of the brake
master cylinder. The main tube line for the rear brake circle will be connected between the
connections for the tank for brake fluid 2 circle.
complete mounted
connection hose brake master cylinder - brake fluid reservoir
Prod.No.
6399
4,30
Prod.No.
6400
3,15
Prod.No.
6401
3,15
Protection bellows for pressure bar input brake master cylinder
Prod.No.
3093
3,95
Repair set for 2-circle brake master cylinder *original*
Prod.No.
7185
9,95
Lenght: 410 mm
Length: 300mm
Length: 350mm
Sleeve set for dual brake master cylinder consist of:
2x annular boot for piston A-circular
2x annular boot for piston B-circular
material: spezial rubber
all parts made in Germany
Seite 29 from178
Screw-cap for brakeline 4,75x0,7 Wartburg and VW
Prod.No.
6378
0,69
Prod.No.
3092
8,49
Prod.No.
6453
19,50
Screw-cap for breakline 4,75mm x 0,7mm
fit to Wartburg 353, Wartburg 1,3 and Opel (Vauxhall)
Sleeve set dual brake master cylinder, complete
Sleeve set for dual brake master cylinder consist of:
2x annular boot for piston A-circular
2x annular boot for piston B-circular
made in EU
Sleeve set for brake master cylinder (1-circuit)
Sleeve set for brake master cylinder of one-circuit brake system
piston diamater: 22,2mm
consist of:
1x annular boot for piston
1x rubber cup sleeve
1x rubber valve sleeve
fit to Wartburg 353 and Barkas B1000 (2-stroke)
Wartburg 353 > Spare parts > Brakes > Front brake
Bolt for brake disk
Prod.No. 6991
0,59
High tensile prestressed hexagon bolt for mounting the brake disk of the Wartburg 353 and 1,3 at the
wheel carrier.
dimension: M8 x 20
strength class: 10.9
surface: galvaniced, silver
made in Germany
Bolt for caliper (W353/W1.3/S130/Rapid)
Prod.No. 6829
0,97
One connecting bolt fit to caliper of Wartburg 353 (only with disc brake system at front axle) and for
Wartburg 1.3 (all variants)
Four pieces will be needed for one caliper.
Seite 30 from178
Brake caliper, complete, right-hand (+50 Euro deposit)
Prod.No.
3076
168,00
Wartburg has got at the front axle a 4-piston brake caliper (fixed suddle)
This caliper is suitable for follow vehicles:
Wartburg 353 (only with disc brake at front axle)
Wartburg 1.3
Skoda 130
Skoda Rapid (120G, 130G, 135G)
Right-hand brake caliper is complete remanufactured (details see brake caliper, component part).
Scope of delivery:
1x right-hand brake caliper, component part
2x brake pad
2x Cotter pin for brake lining (5x80)
1x Spring clamp for brake lining
+ 50 EURO deposit, will be payed back, if old part will be shipping back
Brake caliper, left-hand, complete (+50 EURO pledge)
Prod.No.
3075
168,00
Wartburg has got at the front axle a 4-piston brake suddle (fixed suddle)
This caliper is suitable for follow vehicles:
Wartburg 353 (only with disc brake at front axle)
Wartburg 1.3
Skoda 130
Skoda Rapid (120G, 130G, 135G)
Brake caliper left side is complete remanufactured (details see brake caliper, component part).
scope of delivery:
1x left-hand brake caliper
2x brake lining
2x Cotter pin for brake lining (5x80)
1x Spring clamp for brake lining
Brake caliper, single part, left side (+50 EURO pledge)
Prod.No.
6725
148,00
Wartburg has got at the front axle a 4-piston caliper (fixed suddle)
Caliper left side is complete remanufactured:
new sealed joint face of both caliper case halves and mounted with new high-tension bolts
surface electrogalvanized with olic draped colour
four new pistons with new sealing rings and dust caps
new bleed screws with rubber caps
Delivery as single part without attachments (Cotter pin for brake lining (5x80), Spring clamp for brake
lining and brake lining have to ordered additional).
Seite 31 from178
Brake caliper, single part, right side (W353/W1.3/S105/S120)
Prod.No.
6726
148,00
Wartburg has got at the front axle a 4-piston caliper (fixed suddle)
Caliper right side is complete remanufactured:
new sealed joint face of both caliper case halves and mounted with new high-tension bolts
surface electrogalvanized with olic draped colour
four new pistons with new sealing rings and dust caps
new bleed screws with rubber caps
Delivery as single part without attachments (Cotter pin for brake lining (5x80), Spring clamp for brake
lining and brake lining have to ordered additional).
Brake disk set
Prod.No.
7504
79,90
Prod.No.
3080
48,00
One kit of brake disks fit to Wartburg 353 und Wartburg 1,3.
technical details:
brakedisc Ø 238 mm
highness 69,8 mm
brake disc type: full (without ventilation)
brakedisk thickness: 11,0 mm
minimum thickness: 9,5mm
centrical diameter: 92,0mm
mounting place: front axle
scope of delivery: two pieces
made in EU
Brake disk, singel part
Brake disk fit to Wartburg 353 und Wartburg 1,3.
technical details:
brakedisc Ø 238 mm
highness 69,8 mm
brake disc type: full (without ventilation)
brakedisk thickness: 11,0 mm
minimum thickness: 9,5mm
centrical diameter: 92,0mm
mounting place: front axle
made in EU
Brake drum ( single part ), 50mm
Prod.No. 3074
The brake drum fit only for Wartburg 353 (older model) with brake drum system at the fron axle.
technical details:
for brake shoewide is 50mm
for brake drum diameter: 230mm
bolt circle 4 x 160mm
Reproduction made in Europe
for each car 2 or 4 pieces will be needed
67,56
Brake hose front, drum brake W353
Prod.No. 7123
7,50
Brake hose fit only to Wartburg 353 (older models) with brake drum system at
the front and rear axle.
One pieces will be needed for one front axle.
delivery without brake hose retainer.
Seite 32 from178
Brake hose, front 303mm W353 / W1.3
Prod.No. 3095
5,34
Two pieces needed for each brake suddle of Wartburg 353 (four pieces for the complete front axle).
One piece will be needed for each brake suddle of Warburg 353 and Wartburg 1.3 (4-stroke)
The second Wartburg 1,3 brake hosefor the brake suddle has a length of 350 mm and is also
available
for the Wartburg 353 will be two pieces needed for each brake suddle(A and B-circular)
for the Wartburg 1,3 will be one piece needed for each brake suddle(B-circular)
Brake lining ( incl. 4 pices )
Prod.No.
3081
16,45
Prod.No.
3073
12,88
one complete set of disk brake lining consist of 4 pices.
Fit to Wartburg 353, Wartburg 1.3, Skoda 105 und Skoda 120.
Brake shoe complete, with lining 50mm, single part
brake shoe complete, with lining
wide: 50mm
for brake drums with inner diameter of 230 mm.
fit to Wartburg 353 with brake drum at the front axle, to old version of rear axle and trailer with brake
shoe wide of 50mm
for one wheel side 2 pieces will be needed
Brake shoe set 50mm
Prod.No.
7671
45,50
One set of brake shoes complete, with lining inclusive four pieces.
wide: 50mm
for brake drums with inner diameter of 230 mm.
fit to Wartburg 353 with brake drum at the front axle, to old version of rear axle and trailer with brake
shoe wide of 50mm
One set will be needed.
Cotter pin for brake lining
Prod.No. 3083
Splitted pin for disk brake lining. For each brake suddle two pieces will be needed (4 pieces total).
Fit to Wartburg 353, Wartburg 1.3, Skoda 105 und Skoda 120.
0,48
Gasket ring for brake-suddle pistion ( incl.8 pices )
Prod.No.
3078
6,95
Prod.No.
7239
1,49
for 2 brake suddles
Look plate for steering knuckle leaver
Look plate for hexagon bolt steering knuckle leaver.
Right and left hand mountable.
fit to Wartburg 353 and Wartburg 1.3
sheet matal, *bone style*
made in Germany
you will need 2 pieces at all
Seite 33 from178
Piston for caliper (W353/W1.3/S130/Rapid)
Prod.No. 6828
16,10
One piston fit to caliper of Wartburg 353 (only with disc brake system at front axle) and for Wartburg
1.3 (all variants)
Four pieces will be needed for one caliper.
Protective cap for brake-suddle pistion
Prod.No.
3077
1,95
Prod.No.
Repair-set fit to brake caliper of Wartburg 353/1.3 and Skoda S105 und S120, too.
All parts in outstanding quality.
6723
11,90
4 pieces needed for one brake caliper.
Made by an special manufacture to save the best quality.
suitable for brake caliper of follow car types:
Wartburg 353
Wartburg 1.3
Skoda 105
Skoda 120
Repair-set for brake caliper (W353/W1.3/S130/Rapid)
Inhalt:
4x sealing ring for piston
4x dust protection cap
3x cap for bleeder screw
2 pieces needed for complete front axle
Repair-set for brake caliper PLUS (W353/W1.3/S130/Rapid)
Prod.No. 6938
69,99
Complete set for repairing the brake caliper of Wartburg 353/1.3 and Skoda S120 und Rapid (120G,
130G, 135G), too.
All parts in outstanding quality.
Inhalt:
4x sealing ring for piston
4x dust protection cap
3x cap for bleeder screw
4x brake piston
sealing ring for caliper conduit
1x spring clamp for brake lining
4x cotter pin for brake lining
3x bleeder screw
4x mounting bolt
2 pieces needed for complete front axle
Ring sleeve for wheel brake cylinder
Prod.No. 3072
blow-out patch for wheel brake cylinder left hand or wheel brake cylinder right handfront axle
fit only to Wartburg 353 with brake drum system at the front axle.
scope of delivery:
8,55
complete set incl. 4 pieces
Seite 34 from178
screw for Steering brake suddle
Prod.No. 6320
1,98
hexagon head screw M12 x 1,5 x 30 for mountig brake suddle right hand or brake suddle left hand at
knuckle
surface zinc coated and gold passivated
tensile strength: 10.9
you will need 2 pieces for one brake suddle.
screw for Steering knuckle leaver
Prod.No.
6319
0,99
Sealing ring for caliper conduit, 2 pieces (W353/W1.3/S130/Rapid) Prod.No.
6827
1,83
hexagon head screw M10 x 45
tensile strength: 10.9
made in Germany
you will need 2 pieces for one steering knuckle leaver
One pair of sealing rings fit to connection conduits between caliper halves.
lasts out for one caliper
Sealing ring front brake hose W353 / W1.3
Prod.No. 7687
0,30
Sealing for the connection between brake hose and brake suddle of Wartburg 353 and Wartburg 1,3.
four pieces will be needed
Spring clamp for brake lining
Prod.No. 3082
Fit to the front disk brake system of Wartburg 353, Wartburg 1.3, Skoda 105 and Skoda 120.
For each Brake suddle one pice will be needed.
3,45
Weel-brake cylinder, complete, front, left hand , W353
Prod.No. 3071
35,78
The wheel bake cylinder left hand fit only to Wartburg 353 (older models) with brake drum system at
the front axle
two pieces will be needed for one front axle.
delivery without bleeder screw
Weel-brake cylinder, complete, front, right hand
Prod.No. 3070
35,78
The wheel bake cylinder right hand fit only to Wartburg 353 (older models) with brake drum system at
the front axle
two pieces will be needed for one front axle.
delivery without bleeder screw
Wartburg 353 > Spare parts > Brakes > brake line
brake line set, complete W353
Prod.No. 7264
42,24
Complete brake pipe set made of copper.
Brilliant exchange for old steel lines. Easy to mount, the bending can be done by hand without much
pressure. The set comes with outhlet nuts and complete flanged.
scope of delivery: one set
beanded with nuts
fit to Wartburg 353 with disc brake at the front axle
made in EU
Seite 35 from178
brake line, center rear
(W353/W1.3)
Prod.No.
6696
7,88
brake line rear fit to Wartburg 353 and Wartburg 1.3
This brake line connect the brake pressure regulatoring valve with middle terminal of distributor for
brake lines.
brake line, front, center, left (A-circle)
(W353)
Prod.No.
6692
8,88
brake line front middle right fit to Wartburg 353 (2-circle system)
This brake line connect the upper terminal of brake master cylinder between the two glands for brake
fluid)with anterior brake distributor (A-circle).
new made brake line
surface plastic coated
ready flared with screw fittings
standard form: strong-out (if available also bent)
brake line, front, center, right (B-circle)
(W353)
Prod.No.
6078
7,88
brake line front middle right fit to Wartburg 353 (2-circle system)
This brake line connect the front terminal of brake master cylinder with posterior brake distributor
(B-circle).
original brake line, ready bent for installation
only subject to availability
brake line, front, left (A-circle)
(W353)
Prod.No.
6693
7,88
brake line front, left fit to Wartburg 353 (2-circle system)
This brake line connect anterior brake distributor (A-circle) with frame (joining to brake hose).
brake line, front, left (B-circle)
(W353)
Prod.No.
6694
7,88
3096
4,69
brake line front, left fit to Wartburg 353 (2-circle system)
This brake line connect posterior brake distributor (B-circle) with frame (joining to brake hose).
Wartburg 353 > Spare parts > Brakes > Rear brake
Brake hose, rear
Prod.No.
brake hose for all type of Wartburg (rear brake)
length 200mm
one side with core thread port M10x1
other side with external thread port M10x1
one piece will be needed for each wheel side
Brake pressure regulatoring valve, Limousine
Prod.No. 6459
45,50
Complete pre-mounted spare part. Hydraulic part for infinitely variable adjustment of the brake
pressure rear axle. Direct mechanical triggering from the cargo load.
Fit to all Wartburg 353 and 1,3 Limousine.
original spare part
colour mark: blue
delivery without protecting bellow
Seite 36 from178
Brake pressure regulatoring valve, Tourist
Prod.No. 6678
45,50
Complete pre-mounted spare part. Hydraulic part for infinitely variable adjustment of the brake
pressure rear axle. Direct mechanical triggering from the cargo load.
Fit to all Wartburg 353 and 1,3 station wagon.
original spare part
colour mark: yellow
delivery without protecting bellow
Brake shoe set complete
Prod.No.
3086
34,51
Prod.No.
6888
39,50
Prod.No.
7294
47,50
for Wartburg 353 and Wartburg 1.3
wide: 30 mm
contents:
2x brake shoe with short brake pad
2x brake shoe with long brake pad
2x rivet for brake cable holder
Brake shoe set, rear axle, 50mm
fit to Wartburg 353 with drum brakes at all wheels
wide: 50 mm
contents:
2x rivet for brake leaver
Brake shoe set, rear axle, inclisive leaver, 50mm
fit to Wartburg 353 rear axle, models with drum brakes at all wheels
wide: 50 mm
contents:
2x rivet for brake leaver
hand brake leaver
Brake shoe with long lining
Prod.No. 3085
13,50
brake shoe single part for Wartburg 353 with disc brake system at the front axle and all models of
Wartburg 1,3.
brake shoe wide 30mm
Brake shoe with short lining
Prod.No. 6398
13,50
brake shoe single part for Wartburg 353 with disc brake system at the front axle and all models of
Wartburg 1,3.
brake shoe wide 30mm
scope od delivery: without hand brake leaver and rivet bolt
Seite 37 from178
Dust cap set for rear wheel brake cylinder 19,05mm
Prod.No.
7522
8,50
Prod.No.
3090
10,20
Rubber sleeve, for the outside of the wheel brake cylinder (set incl. 2 pieces )
fit for Wartburg 353 and wartburg 1,3.
The dust cap protect the brake pistion against brake dust and moisture.
fit to brake piston diameter 19,05mm
made in Europe
one piece will be needed for each wheel side rear
Handbrake cable, complete
handbrake cable for for Wartburg (rear axle).
fit to all type of Wartburg 3 and 4 cylinder engine.
both cables are symmetric and have the same length
the complete lenght is 160 cm
Mounting screw wheel brake cylinder, rear axle, Wartburg
Prod.No. 7521
0,95
Hexagon bolt inclusive lock washer for mounting the rear brake cylinder at the drum brake base plate.
Fit to all kind of Wartburg models.
surface: zinc galvaniced
grade: 10.9
scope of delivery inclusive lock washer
Protection bellows for pressure bar input brake pressure regulatoring Prod.No.
valve
3094
6,90
Prod.No.
7149
8,25
Prod.No.
Made in Europe set of ring sleeve, for wheel brake cylinder (set incl. 2 pieces )
fit for Wartburg 353 and wartburg 1,3
for one wheel brake cylinder, rear axle Art.Nr. 3087
3088
9,22
7004
7,24
Protection bellows for Barkas and Wartburg
Ring sleeve, for rear wheel brake cylinder original, 19,05mm
Ring sleeve, for wheel brake cylinder (set incl. 2 pieces )
fit for Wartburg 353 and wartburg 1,3
fit to brake piston diameter 19,05mm
made in Germany
Ring sleeve, for rear wheel brake cylinder, 19mm, EU
fit to brake piston diameter 19mm
reproduction EU
Sealing plate for hand brake lever (W353/W1.3)
Prod.No.
Sealing plate for hand brake lever made of black rubber.
fit to all variants of Wartburg 353 (2-stroke) and 1.3 (4-stroke)
1 piece will be needed for each car
Seite 38 from178
Weel-brake cylinder, rear , W353 (old version)
Prod.No. 6198
39,50
Wheel brake cylinder for the Wartburg 353 rear axle.
This kind of brake cylnder fit to Wartburg 353 with brake drums at the front axle as well as some
Wartburg 353 models form vintage 1975-1982 with disc brake system at the front axle.
Please note, if you have an Wartburg model between the vintage 75-82 you have to check out the kind
of mounted wheel brake cylnder before you place an order (piston diameter 25,35 or 19mm)
technical details:
piston-diameter: 25,35 mm
connection thread for brake line: M10x1
for brake drum diameter: 230mm
for brake shoe wide: 50mm
Reproducion made in Europe
Wheel brake cylinder, rear axle, original, D=19mm
Prod.No. 7237
35,75
Complete in Germany overhauled rear wheel brake cylinder with ring sleeves, brak-piston D=19mm.
Mark: IFA BHL
Fit to Wartburg 353 (with disc brake at the front axle) and Wartburg 1.3
fit to brake shoes with the wide of 30mm
scope of delivery: inclusive ring sleeves and bleeder screw)(break piston diameter: 19 mm
Wheel brake cylinder, rear axle, original, D=25,35mm
Prod.No. 7315
28,50
Complete in Germany overhauled rear wheel brake cylinder with ring sleeves, brak-piston
D=25,35mm.
Mark: IFA BHL
This kind of brake cylnder fit to Wartburg 353 with brake drums at the front axle as well as some
Wartburg 353 models form vintage 1975-1982 with disc brake system at the front axle.
Please note, if you have an Wartburg model between the vintage 75-82 you have to check out the kind
of mounted wheel brake cylnder before you place an order (piston diameter 25,35 or 19mm)
scope of delivery: inclusive ring sleeves, dust caps and bleeder screw)(break piston diameter: 25,35
mm
Wheel brake cylinder, rear brake
Prod.No. 3087
28,50
brake cylinder for rear wheel brake fit to Wartburg 353 (with disc brake at the front axle) and Wartburg
1.3
piston diameter 19mm
made in EU
Wartburg 353 > Spare parts > Electrical system
Seite 39 from178
Diode base plate for Dynamo AC
Prod.No. 7602
28,75
Spare base plate complete pre installed with excitation diodes and plus diodes.
Best use for exchanging the complete componet.
Delivery without mounting parts.
Fit to dynamo 12V Wartburg 353 and Barkas B1000 and dynamo 12V Wartburg 1.3, Trabant 1.1 and
Barkas B1000-1.
original spare part
one base plate will be needed
Dynamo inclusive regulator, rotary current AC 12V
Prod.No.
3150
156,00
Rotary current generator complete overhauled spare part.
Fit to Wartburg 353 and Barkas B1000.
Scope of delivery inclusive mounted voltage regulator
Please note: for this spare part we will charge an additional deposit. This plede is not included at the
actually signified sale price. The pledge will be paid back after your old spare part returns to our
company
made in Germany
Dynamo without regulator, rotary current AC 12V
Prod.No.
7361
145,00
Rotary current generator complete overhauled spare part.
Fit to Wartburg 353 and Barkas B1000.
Scope of delivery without 12V voltage regulator
Please note: for this spare part we will charge an additional deposit. This plede is not included at the
actually signified sale price. The pledge will be paid back after your old spare part returns to our
company
made in Germany
Wartburg 353 > Spare parts > Electrical system > Lighting
direction indicator lamp, front ( yellow )
Prod.No.
6413
19,73
Prod.No.
3050
4,88
front direction light for Wartburg 353
consist of:
insert seal for direction indicator
glass for direction indicator
holder of light bulb
original-IFA-spare part
Glass for direction indicator lamp, front
Lense for the drection indicator Wartburg 353. Fit to front left and right hand.
Genuine bit (NOS), best quality.
colour: orange
Seite 40 from178
Glass for flasher stop tail lamp ( white / red ) W353
Prod.No. 3053
18,50
Special rear light lense fit to Wartburg 353 limousine and station wagon left and right hand. The class
have insted of the orange cloured flasher a clear lense.
1x red for stopligth 21W
1x red for rearlight 5W
1x clear for flasher 21W
made in EU
Glass for flasher stop tail lamp ( yellow / red ), W353
Prod.No. 3052
18,50
Rear light lensefit to Wartburg 353 limousine and station wagon left and right hand. The class is
cloured like the original one:
1x red for stopligth 21W
1x red for rearlight 5W
1x orange for flasher 21W
made in EU
Headlamp
Prod.No.
6610
48,95
headlamp light for Wartburg 353 up to vintage 6 / 1985 for right and left side
consist of:
mechanical beam adjustment
original spare part
Zak No: 8704.40 / 2-1
for H4 bulbs
Lense for number plate lights, W353
Prod.No. 7707
3,20
Clear plastic lense for the number plate ligthing fit to rear bumper of Wartburg 353 and Wartburg 1.3
Trans (rare pickup-type of Wartburg)
Can be used for the black and chrome models of the nuber plate spots.
two pieces will be needed for one bumper
original spare part
light for number plate, black W353
Prod.No. 6611
9,90
Complete lamp for number plate ligthing fit to rear bumper of Wartburg 353 and Wartburg 1.3 Trans
(rare pickup-type of Wartburg)
Consist of:
Cover cap, black
lens
upper gasket
socket incl. bottom case
bottom gasket
holder bracket incl. mounting bolt
Seite 41 from178
light for number plate, chrome W353
Prod.No. 7257
24,20
Complete lamp for number plate ligthing fit to rear bumper of Wartburg 353 and Wartburg 1.3 Trans
(rare pickup-type of Wartburg)
Consist of:
Cover cap, chrome
lens
upper gasket
socket incl. bottom case
bottom gasket
holder bracket incl. mounting bolt
Light switch W353, extension element
Prod.No.
7535
20,97
Prod.No.
6052
20,50
Prod.No.
Sealing for the rear lights of the Wartburg 353 (all models Limousine and Tourist)
Colour black, fit to right or left hand Wartburg 353.
6053
12,45
Taillight W353
Prod.No.
7466
29,50
bayonet fuel tank plug, lookable
Prod.No.
3545
16,98
Flange seal for fuel pump
Prod.No.
6765
6,16
Switch for the lightings of the Wartburg 353 all models.
Spare part is an used part, checked for function.
original spare part
Zak No: 8620.16 /08656
one pieces will be needed
Seal for indicator insert, front
Rubber sealing for the front indicator insert. Fit to left and right hand.
fit to all Wartburg 353
original spare part
Sealing plate for flasher stop tail lamp
Flasher stop tail lamp for Wartbrug 353 Limousine und Tourist.
Fit at the vehicle right and left hand.
Scope of delivery 1x rear light lense + 1x base carrier.
Original spare part
Wartburg 353 > Spare parts > fuel system
rubber seal for flange of fuel pump
two pieces will be needed for each fuel pump ( one between engine block and insulation piece and
another one between insulation piece and fuel pump
fit for all fuel pumps Wartburg 353 and B1000
Seite 42 from178
float gauge for carburettor (new type) Jijkov
Prod.No.
6622
31,73
carburettor float gauge for carburettor of Wartburg 353, B1000 called Jijkov
made of plastic
only few pieces available (originale spare part)
float gauge for carburettor (old type) 40 F
Prod.No. 6517
29,50
carburettor float gauge for old type of carburettor of Wartburg 353, B1000 and Robur (LO) called 40 F
Float needle valve, complete
Prod.No.
6541
9,85
The needle velve controls the volume of the float housing.
material: brass
nozzle: 18
typ: tongued
fit to all Wartburg 353 and Barkas B1000 carburettor typs (only fit to type 40F and not to Jijkov
Fuel pump
Prod.No.
3140
28,44
Prod.No.
6238
13,97
Fuel pump for Wartburg 353 and Barkas B1000 (2-stroke engine)
complete component
Fuel tank plug, lookable
Insulation piece for fuel pump
Prod.No. 6766
8,55
insulation plate for flange of fuel pump
This insulation plate reduced the factor of heat from engine block to the fuel pump. It protects from blowholes when the fuel
evaporates because of to much heat.
one piece will be needed for each fuel pump
it will mounted between two flange rubber seals
made of plastic
paper seal for flange throttle valve (carburettor 40 F)
Prod.No. 6485
seal for flange throttle valve of old type of carburettor of Wartburg 353 and B1000, called 40 F
2,74
two pieces needed for one carburettor
mounted between flange throttle valve (carburettor 40 F) and cover of carburettor (drainer)
between cover of carburettor (drainer) and intake manifold
fit for Wartburg 353 und B1000
Seite 43 from178
rubber seal for flange throttle valve (carburettor 40 F)
Prod.No. 6486
4,55
rubber seal for flange throttle valve of old type of carburettor of Wartburg 353 and B1000, called 40 F
one pieces needed for one carburettor
mounted between flange throttle valve (carburettor 40 F) and carburettor case
seal for carburettor case (new type) Jijkov
Prod.No.
6479
6,85
Prod.No.
seal for housing of old type of carburettor of Wartburg 353 and B1000, called 40 F
6478
3,88
seal for the new type of carburettor of Wartburg 353, called Jijkov-carburettor
matreial: sealing paper
seal for carburettor case (old type) 40 F
Seal for carburettor flange (new type) Jijkov
Prod.No. 6518
3,98
seal for flange from the new type of carburettor of Wartburg 353, called Jijkov-carburettor to the intake
manifold.
material: sealing paper
made in Germany
two ore three piece will be needed
1x carburettor-isolating plate, 1x isolating plate-cover plate, 1x cover plate-succition pipe
Seal for flange suction pipe - engine block
Prod.No. 6897
Paper seal for flange of the inlet manifold of the carburettor type 40 F, Jijkov and 36F. Mounted:
7,50
between flange inlet manifold and engine mount
one pieces needed
Self-repair-set carburettor 40F
Prod.No.
6985
8,50
Prod.No.
6984
14,59
Prod.No.
6178
59,69
5-part jet set for the carburettor of Wartburg 353, B1000 called Berliner-40F
delivery inclusive gauge needle valve
Self-repair-set carburettor Jijkov
11-part jet set for the carburettor of Wartburg 353, B1000 called Jijkov
delivery inclusive gauge needle valve
Sensor for KMVA (display for fuel consumption)
KMVA sensor for Wartburg 353
original made Germany by IFA
Seite 44 from178
Spare kit for fuel pump
Prod.No.
3142
15,17
fuel pump spare kit constist of:
1 x membran; 1 x pressure spring, 2 x valves, 1 x strainer, 2 x seal,
1 sealing ring (rubber)
Transmitter for fuel gauge
Prod.No. 6690
46,47
Sensor for fuel gauge with potentiometer for connection to all offert fuel gauges. Complete with rubber
sealing and float. Fit to Wartburg 353 and Wartburg 1,3.
additional switch for reserve control lamp (GR)
made in Germany
Wartburg 353 > Spare parts > Engine
Air filter
Prod.No.
3175
7,76
Prod.No.
7229
8,94
air filter fit to all Wartburg and Barkas with two stroke motor.
no specification or manufacturing year limit.
made in Germany
Air filter
air filter fit to all Wartburg and Barkas with two stroke motor.
no specification or manufacturing year limit.
made in Germany
with expanded metal as cover (no paperboard with holes) for better air flow
Carburettor bowdencable W353
Prod.No. 3510
6,05
Throttle control cable for all kind of carburettors (40F und Jijkov) Wartburg. Machanical connection
between accelerator and throttle valve of the carburettor.
total length: 101 cm
length of the bowdencabe cover: 81 cm
made in EU
Carburettor W353
Prod.No. 7031
145,00
Complete overhauled Carburettor for the three cylinder two stroke Wartburg engine with 1000 ccm
Carburettor type: 40F 2-11
Please note, we can only exchange you this spare part if you ship 1x carburettor 40 F2-11 to our
company in advance!
crank shaft with reinforced lower bearing of conrod, 50PS (horse power)
Prod.No. 6996
728,00
(+150? deposit)
crank shaft with modified version of conrod with strengthened lower bearing (with steel cage in place of aluminium cage)
+150? pledge
Seite 45 from178
crank shaft, 45hp
(+150? pledge)
Prod.No.
6415
650,00
Crank shaft with standard version of conrod and modificated feet bearings made (cage of steel).
for all engines of 2-stroke B1000 and for Wartburg 353 engine with 45 horsepower
+150? pledge
Crank shaft, 45hp, with slotted conrod
Prod.No. 6416
630,70
(+150? pledge)
Crank shaft for all engines of B1000 and Wartburg 353 engine 2-stroke with 45 horse power.
Spezial connection rod with slotted version of the conrod eye for more considerable better lubrication
of the feet bearings
type: serial bearing cage (aluminium)
+150? pledge
crank shaft, 50hp
Prod.No.
(+150? pledge)
complete overhauled crank shaft with full plates for Wartburg 353 engines with 50 hp.
6116
650,00
Crank shaft with standard version of conrod and modificated feet bearings made (cage of steel)
delivery inclusive needle bearings for the piston pins
+150? pledge
crank shaft, 50hp, with slotted conrod
(+150? pledge)
Prod.No.
6117
650,00
Prod.No.
6999
780,00
Prod.No.
6482
780,00
Prod.No.
Starter freewheel complete premounted inclusive pinion (9 teeth).
Fit to Wartburg 353 and Barkas B1000 (2-stroke).
This part is made in Europe. High quality, best replacement for the genuine spare part.
7643
25,43
crank shaft with slotted version of conrod for better lubrication
for Wartburg 353 engine with 50 horse power
+150? pledge
Engine block 45hp
(+150? pledge)
engine mount for Wartburg 353 and Barkas 1000 with 45 horse power.
Motor block is nutshells blasded for cleaning and coated wit 2-K varnish (black).
Cylinders are grinded and honed, inclusice 3 pistions made in Germany.
Scope of delivery complete with pistons, piston rings and pistion pins.
+150? pledge
Engine block 50hp
(+150? pledge)
engine mount for Wartburg 353 engine with 50 horse power.
Motor block is nutshells blasded for cleaning and coated wit 2-K varnish (black).
Cylinders are grinded and honed, inclusice 3 pistions made in Germany.
Scope of delivery complete with pistons, piston rings and pistion pins.
+150? pledge
Freewheel for starter 12V (W353/B1000)
Seite 46 from178
Freeze cap
Prod.No. 7255
Plate shape plug for secure the motor block for freeze demages.
Fit to all cooling water holes diameter 36mm for the Wartburg and Barkas with two stroke motor.
made in Germany
6,76
Magnet, complete for starter 12V
Prod.No.
6066
39,49
Prod.No.
6880
0,55
Prod.No.
6386
4,22
Prod.No.
6199
5,50
Magnet switch for the starter motor of the Barkas B1000 und Wartburg 353.
voltage 12V
spare part is made in EU
Mounting bolt for inlet pipe
Bolt for flange of the inlet pipe to the connection to the engine.
Fit to flange with the Berlin carburettor or the Jijkov-carburettor.
hexagon socket screw M8 x 16mm
strength class: 8.8
with external teeth lock washer
galvaniced
total: 8 pieces will be needed
mounting set for starter 12V
mounting set for starter consist of:
2x screw M12 x 100
2x washer
2x nut M12
Needle bearing for crankshaft, flywheel-side
needle bearing for additionally clamping of clutch-shaft in crankshaft
K 12 x 16 x 13
Piston ring sealing crank shaft (W353/B1000)
Prod.No. 6903
11,50
Special piston ring for the sealing of the crank case. Can be mounted at the flywheel and the v-pully
side, crankshaft with 45 hp or 50 hp.
fit to 2-stroke-engines of Wartburg 353 and Barkas B1000
4 piece will be needed for each engine
safety plate beltwheel (W353/B1000)
Prod.No. 7154
Locking plate for the two srews, which are necessary to mount the beltwheel at crankshaft.
2,97
surface: galvanized
fit to 2-stroke-engines of Wartburg, Barkas B1000
one piece will be needed for each engine
safety plate flywheel (W353/B1000)
Prod.No.
620
Locking plate for the five srews, which are necessary to mount the flywheel at crankshaft.
9,98
surface: galvanized with olive drap colour
fit to 2-stroke-engines of Wartburg 311, 312, 313, 353, Framo Barkas B1000
one piece will be needed for each engine
Seite 47 from178
Special bolt flywheel (W353/B1000)
Prod.No.
One-off-production of the hexagon screw for mounting the flywheel at the crankshaft.
6904
5,20
3155
119,99
tap: M8
spanner gap: 13
surface: galvanized
fit to 2-stroke-engines of Wartburg 311, 312, 313, 353, Framo, Barkas B1000
5 pieces will be needed for each engine
Starter 12V, complete (W353/B1000) +30,00 Euro deposit
Prod.No.
Starter inclusive magnet for starter fit to Wartburg 353 and Barkas B1000 (2-stroke).
Spare part is overhauled in Germany. High quality.
voltage: 12V
output: 0,58KW
pinion teeth: 9
When you buy this starter you have to pay additional 30,00 Euro deposit for the old starter. After you
given this old part back to us, the deposit of 30,00 Euro will be transfered to your bank account.
Please put a slip of paper with your customer no., invoice no. and your (international) bank account
details or better your email address of PayPal account on it into the parcel (Or tell us this informations
by email). You have to pay the shipping costs for yourself
Startmixture bowdencable
Prod.No.
3520
10,14
bowdencable for startmixture Wartburg 353 (two stroke engine)
Tuning crank shaft with reinforced lower bearing of conrod,
Prod.No.
(+150?
deposit) 6997 1199,00
crank shaft with modified version of conrod with strengthened lower bearing eminently suited up to
10.000 revolutions per minute (RPM)
stuffed holes inside of crankwebs to increase the pre-compression
new produced, selected and polished tuning conrod with slotted conrod eye for better lubrication
reinforced lower conrod bearings with steel cage in place of aluminium cage
scope of delivery: crank shaft incl. needle bearings for piston pin und piston ring sealing
very good quality made in Germany
+150? pledge
Tuning crank shaft with reinforced lower bearing of conrod,
Prod.No.
(+150?
deposit) 6998 1499,00
crank shaft with modified version of conrod with strengthened lower bearing eminently suited up to
10.000 revolutions per minute (RPM)
same technology like standard-Tuning crank shaft but additionally with polished crankwebs
stuffed holes inside of crankwebs to increase the pre compression
new produced, selected and polished tuning conrod with slotted conrod eye for better lubrication
reinforced lower conrod bearings with steel cage in place of aluminium cage
scope of delivery: crank shaft incl. needle bearings for piston pin und piston ring sealing
all-out best quality made in Germany
+150,00? deposit
V-belt (W353 / B1000)
Prod.No. 3176
14,40
V-belt 10 x 1150 fit to Wartburg 353 and Barkas B1000 to transmit the rotary to the dynamo and to the
wather pump shaft.
size: 10 x 1150 mm
new German production
Wartburg 353 > Spare parts > Engine > Piston
Seite 48 from178
Piston ( 73,50 mm )
Prod.No. 3125
99,98
piston complete for Wartburg 353 and Brakas B1000 2-stroke
piston size 73,50
made in Germany, original aluminium alloy, original crowned contour, with one hard chrome-plated
piston ring on top.
the set included:
1x piston 73,50
3x pistonrings 73,50
1x pistonpin
2x pistonclip
Piston ( 73,75 mm )
Prod.No. 3126
99,98
piston size 73,75
piston ring on top.
the set included:
1x piston 73,75
1x pistonpin
2x pistonclip
Piston ( 74,00 mm )
Prod.No. 3127
99,98
piston size 74,00
piston ring on top.
the set included:
1x piston 74,00
1x pistonpin
2x pistonclip
Piston ( 74,25 mm )
Prod.No. 3128
99,98
piston size 74,25
piston ring on top.
the set included:
1x piston 74,25
1x pistonpin
2x pistonclip
Piston ( 74,50 mm )
Prod.No. 3129
99,98
piston size 74,50
piston ring on top.
the set included:
1x piston 74,50
1x pistonpin
2x pistonclip
Seite 49 from178
Piston ( 75,00 mm )
Prod.No. 3130
99,98
piston size 75,00
piston ring on top.
the set included:
1x piston 75,00
1x pistonpin
2x pistonclip
Piston pin
Prod.No.
6307
8,50
Prod.No.
6023
9,52
Prod.No.
6026
9,52
Prod.No.
6497
18,24
Prod.No.
6498
18,24
Prod.No.
6499
18,24
The piston pin fit to all piston sizes (73,50 - 75,00).
One pistion need one pin.
For Wartburg 353 and B-1000 with 2-stroke 3 cylinder engine.
diameter20 mminner diameter12 mmlenght63 mm
Pistonring 73,50 mm
The piston ring fit for piston 73,50piston.
For Wartburg 353 and B-1000 with two stroke 3 cylinder engine.
material: special gray iron
For one pistion 3 rings will be needed
Pistonring 74,25 mm
Pistonring chrome 73,50 mm
The chrome-piston ring fit for piston 73,50piston.
It will be mounted on top of the pistion.
cylinder bore: 73,50mm
material: special gray iron, hard chrome-plated
for each pistion one chromering will be needed
Seite 50 from178
Prod.No.
6500
18,24
Prod.No.
6501
18,24
Prod.No.
6502
18,24
Prod.No.
6024
9,52
Prod.No.
6025
9,52
Prod.No.
6027
9,52
Prod.No.
6028
9,52
Pistonring 73,75 mm
Pistonring 74,00 mm
Pistonring 74,50 mm
Pistonring 75,00 mm
Seite 51 from178
Pistonring- set 73,75 mm
Prod.No.
6506
36,00
Prod.No.
6503
36,00
Prod.No.
6505
36,00
Prod.No.
6507
36,00
Prod.No.
6508
36,00
Prod.No.
6509
36,00
The piston ring set fit to piston 73,75piston.
set consist of 6x piston ring and 3X chrome piston ring
complete set for three pistions, one set will be needed
Wartburg 353 > Spare parts > Engine > cooling system
Seite 52 from178
blow off valve for compensating reservoir, 50kPa (W353/B1000)
Prod.No. 6553
12,49
Blow off valve for coolant compensating reservoir of Wartburg 353 and 2-stroke version of Barkas
B1000.
It will be mounted inside reservoir cap.
pressure: 50kPa
made in EU
Bolt for pump housing
Prod.No. 6859
Hexagon bolt for the water pump case fit to all Wartburg 353 and B1000 two stroke engine
0,92
delivery inclusive washer
six pieces will be needed
Bolt for thermostat case
Prod.No. 6858
Hexagon bolt for the Thermostat manifold fit to all Wartburg 353 and B1000 two stroke engine
0,92
compensating reservoir (W353/B1000/M25)
Prod.No.
6728
39,21
Prod.No.
7378
6,50
Prod.No.
7379
5,68
Prod.No.
7381
15,50
Coolant compensating reservoir with one gland on bottom.
This coolant reservoir is suitable for follow car types:
Wartburg 353
B1000 (only 2-stroke)
Multicar M25
Suitable accessory:
blow off valve 50kPa
closure
Coolant hose W353 up to May 1985
Water hose for the Wartburg 353 with radiator behind the engine.
Fit to Wartburg 353 Limousine, Tourist and Trans up to vintage Mai 1985.
Coolant from thermostat casing of the cylinder head to the radiator upper connection
Coolant hose W353 up to May 1985 Compensating tank
Coolant from compensating reservoirto to the radiator connection
Coolant hose W353 up to May 1985 from heat exchanger
Coolant from the heat exchanger the thermostat casing on top of the cylinder head
Seite 53 from178
Coolant hose W353 up to May 1985 to heat exchanger
Prod.No.
7380
15,50
Coolant from the water pump to the heat exchanger
fan wheel water pump from 5/85
Prod.No. 7345
19,50
Waterpump wheel fit to Wartburg 353 (from vintage Mai 1985) and all Barkas B1000 (3 cylinder
2-stroke engine)
1x fan wheel with 2xmetal ring for membran sealing
made in Europe
Fan wheel water pump up to 5/85
Prod.No. 7344
23,55
The waterpump wheel fit to Wartburg 353 (up to vintage Mai 1985) with three cylinder 2-stroke engine
1x fan wheel with 2xmetal ring for membran sealing
made in Europe
gasket ring of sensor for temperature
Prod.No. 6565
0,18
Aluminium ring for the temperature sensor mounted in cylinder head of 2-stroke engine of Wartburg
353 and barkas B1000.
outer-diameter: 20 mm
inner-diamter: 14 mm
thickness: 1,5 mm
Lower radiator hose (W353 from June 1985 onwards)
Prod.No. 7025
14,49
fitted coolant hose to connect the connection piece (connected with lower cooler connection) with
water pump of Wartburg 353 with vintage from June 1985 onwards (radiator is placed in front of
engine).
Length: ca. 41 cm
Inner diameter: 24 mm
Outer diameter: 34 mm
Lower radiator hose (W353 up to May 1985)
Prod.No. 7024
8,55
fitted coolant hose for lower cooler connection of Wartburg 353 with vintage up to May 1985 (radiator
is placed behind the engine).
Inner diameter: 24 mm
Outer diameter: 34 mm
Length: 22cm
Radiator
Prod.No.
6295
138,00
radiator for Wartburg 353 from vintage: may 1985.
The cooler is placed in front of the engine.
radiator with aluminium-rib
made in EU
Seite 54 from178
Radiator hose set(W353 from June 1985 onwards)
Prod.No. 7488
55,92
Complete set oft coolant hoses to for the Wartburg 353 with vintage from June 1985 onwards (radiator
is placed in front of engine).
Fit to all types like Limousine, Tourist and Trans.
Scope of delivery:
1x radiator hose: 29x390mm
Seal for thermostat case
Prod.No.
3136
2,20
Prod.No.
3139
2,20
Prod.No.
7253
2,50
Thermostatseal fit to all Wartburg 353 and B1000 two stroke engine
material: seal-paper
Seal for water pump
Waterpump seal fit to all Wartburg 353 and B1000 two stroke engine
Seal for water pump, labyrinth
Some Wartburg and B1000 engines have an splitted pump case.
This Waterpump seal fit to the outer cap, the labyrinth housing.
For the total sealing you need additional still the normal water pump seal
Sealing ring for thermostat
Prod.No. 7007
3,33
Sealing ring made of black rubber fit thermostat of all Wartburg 353 and Barkas B1000 with 3 cylinder
two stroke engine.
[mad in Germany][one piece will be needed]}
sensor for temperature
Prod.No.
6554
23,95
Prod.No. 3138
fit to Wartburg 353 (from vintage Mai 1985) and all Barkas B1000 (3 cylinder 2-stroke engine)
complete set consist of:
68,67
Transmitter for temperature indication
thread: M14 x 1,5
width across flats: 19mm
Spare kit for water pump from 5/85
1x fan wheel
1x membran gasket compl.
2x cover disc for ball bearings
1x gasket for ball bearing (rubber), side of belt pulley
1x distance bush (inner bush)
1x O-ring
Seite 55 from178
Spare kit for water pump up to 5/85
Prod.No.
fit to Wartburg 353 (up to vintage Mai 1985) with three cylinder 2-stroke engine
complete set consist of:
3137
85,29
Prod.No. 7286
Thermoswitch for the electrical radiator fan of the Wartburg 353 from vintage: may 1985.
The switch is mounted upside the lower connector for the cooling water at the radiator.
16,66
1x fan wheel
2x membran gasket compl.
2x cover disc for ball bearings
1x gasket for ball bearing (rubber), side of belt pulley
1x distance bush (inner bush)
1x O-ring
switch for radiator fan
delivery inclusive sealing ring
made in Germany
Thermostat
Prod.No.
3135
11,87
Prod.No.
6937
25,90
Fit to all Wartburg 353 and Barkas with 3 cylinder two stroke engine.
incl. sealing ring
Thermostat opens by 82°C
Valve for cooling water
Brass drain cock will be mounted direct on the motor block (exhaust side).
Fit to: Wartburg 311, 312,313, 353, Framo, Barkas B1000.
Water pump shaft 42cm up to 5/85
Prod.No. 7382
68,00
Transmission shaft for cooling pump at the cylinder head of the Wartburg 353 Limousine, Tourist or Trabs (up to vintage
Mai 1985) with three cylinder 2-stroke engine
material: steel
with knurling for fan
Original spare part
length total: 42cm
Water pump shaft from 6-85
Prod.No. 7383
68,00
Transmission shaft for cooling pump at the cylinder head of the Wartburg 353 Limousine, Tourist or Trabs (up to vintage
June 1985) with three cylinder 2-stroke engine.
Wartburg type with radiator in front of the engine an elektrical cooling fan.
material: steel
Original spare part
length total: 38cm
Wartburg 353 > Spare parts > Engine > clutch
Seite 56 from178
Clutch up to 6/85
+20,00? deposit
Prod.No.
3101
104,20
3100
62,20
Clutch for Wartburg 353 models up to year June 1985.
fit to clutch disc diameter 180mm (type 180DER oder 180DE2R, our order no. 3100)
with additional thrust bearing for old version of release bearing
Clutch disk (W353/B1000/M24), Made in Germany, +50? deposit
Prod.No.
clutch disc with springs
fit for all variants of Wartburg 353 (vintage up to 05/1985), for Barkas B1000 (vintage up to 02/1985)
and also for Multicar M24
diameter: 180 mm
Clutch disk W353, Made in EU, +10? deposit
Prod.No.
6560
40,25
clutch disc with springs
fit for all variants of Wartburg 353 and for Barkas B1000 up to 02/1985
diameter: 180 mm
Information about the deposit:The clutch disc is to exchange for the old one, to enable the
overhauling. There are two possibilties to get this clutch disc.
(1) The old clutch disc (worned out) is to ship to us before we ship the new disc (after an
acknowledged order).
(2) You have to pay additional 10,00 Euro (deposit for old clutch disc) in your invoice. After you
shipped back these parts to us, the money (10,00 Euro) will be transfered back to your account.
Please put a slip of paper with your customer no., invoice no. and your (international) bank account
details or better your email address of PayPal account on it into the parcel (Or tell us this informations
by email). You have to pay the shipping costs for yourself.
Clutch release bearing from 6/85
Prod.No.
3105
34,15
Prod.No.
3104
34,13
Prod.No. 6558
If the clutch slips during driving with 3. or 4. gear, the clutch components have to change.
178,20
letest version of clutch release bearing for Wartburg 353
made in Europe
fit to all Wartburgs from vintage June 1985 onwards
Clutch release bearing W353 up to 6/85; B1000 up to 02/1985
Clutch release bearing for cluch fit to the following car:
Wartburg 353, up to year 06/1985
Barkas B1000, up to 02/1985 (in tandem with clutch disc with diameter of 180 mm)
Clutch set *W353* (for vintage from 05/1985 onwards)
This clutch set fits to all variants of Wartburg 353 with a vintage from 06/1985 onwards.
content:
180mm clutch (from vintage June/1985 onwards)
180mm cluch disc with springs
release bearing (from vintage June/1985 onwards)
All parts were made or overhauled in Germany.
Seite 57 from178
Clutch set *W353* (for vintage from 05/1985 onwards)
Prod.No.
6559
125,67
This clutch set fits to all newer variants of Wartburg 353 with a vintage from 06/1985 onwards.content:
180mm clutch (from vintage June/1985 onwards)
release bearing (from vintage June/1985 onwards)
All parts were imported from (mostly east European) foreign countries. The Quality of these parts are incomparable to the
quality of parts made in Germany. The working life could be lower, the meantime between failure could be lower, because
the materials have not the same quality.
Clutch set *W353* (for vintage up to 05/1985)
Prod.No.
6556
178,20
This clutch set fits to all variants of Wartburg 353 with a vintage up to 05/1985 and also for type 312.content:
180mm clutch with additional thrust bearing for old version of release bearing (up to vintage May/1985)
release bearing (up to vintage May/1985)
Information about the deposit:The clutch and clutch disc are to exchange for the old one, to enable the overhauling. There
are two possibilties to get this clutch set.
(1) The old cluch + clutch disc (worned out) are to ship to us before we ship the new set (after an acknowledged order).
(2) You have to pay additional 30,00 Euro (deposit for old clutch + clutch disc) in your invoice. After you shipped back these
parts to us, the money (30,00 Euro) will be transfered back to your account. Please put a slip of paper with your customer
no., invoice no. and your (international) bank account details or better your email address of PayPal account on it into the
parcel (Or tell us this informations by email). You have to pay the shipping costs for yourself.
Clutch set *W353* (for vintage up to 05/1985) , made in EU
Prod.No.
6557
134,30
This low priced clutch set fits to all variants of Wartburg 353 (perhaps also for type 312).content:
180mm clutch with additional thrust bearing for old version of release bearing (up to vintage May/1985)
release bearing (up to vintage May/1985)
All parts were imported from (mostly east European) foreign countries. The Quality of these parts are incomparable to the
quality of parts made in Germany. The working life could be lower, the meantime between failure could be lower, because
the materials have not the same quality.
Clutch W353 from vintage 6/85 onwards
Prod.No.
3102
104,20
Clutch for Wartburg 353 models with vintage from June 1985.
fit to clutch disc diameter 180mm (type 180DER oder 180DE2R, our order no. 3100)
without additional thrust bearing for release bearing
Friction surface for clutch disc (W353/B1000/M24)
Prod.No. 7672
24,66
Set of two pieces friction surfaces for clutches 180mm diameter.
Best for self made at the worn out clutch disc.
Fit for all variants of Wartburg 353 (vintage up to 05/1985), for Barkas B1000 (vintage up to 02/1985)
and also for Multicar M24
size: 180x124x3,5mm
complete pree drilled
made in germany
Seite 58 from178
Spring fpr clutch release bearing from 6/85
Prod.No.
7328
2,49
Prod.No. 6834
Deep groove ball bearing fit to all Wartburg 353 and Barkas B1000 2-stroke engines with
contact breaker ignition or electronic ignition EBZA.
8,40
Snap clamp for mounting the pressure bearing at the release shaft.
Fir to the following car types:
Wartburg 353 ab 6-1985 Limousine and Tourist
Trabant 1,1 without vintage limit Kombi and Limousine
Wartburg 1,3 without vintage limit Tourist and Limousine
Barkas B1000 ab 3-85 with clutch D=200mm
Barkas B1000-1 without vintage limit
Wartburg 353 > Spare parts > Engine > Ignition system
Bearing for ignition case - timing shaft
ball bearing coverd on both sides
producer: FAG
Cover for ignition case W353/B1000
Prod.No. 6449
Plastic cover for the ignition case of the Wartburg 353 and Barkas B1000 2-stroke engine.
Fit for contact breaker ignition system and electronic ignition system (EBZA)
6,47
new production made in EU
material: plastic
colour black, withe or red
Elektronic ignition adapter kit
Prod.No.
3162
134,87
Elektronic ignition adapter kit for Wartburg 353 and Barkas ? Two stroke
Elektronic ignition box for EBZA2f (with power amplifier)
Prod.No. 6046
148,00
spare part for the original Elektronic ignition box for EBZA2f for Wartburg 353 and Barkas ? Two
stroke
works with the original sensors
ignition cable set, high quality W353
Prod.No.
6446
22,12
pre-finished ignition cable set for Wartburg 353
consist of:
three ignition cables with right length (high quality, made in Germany, very flexible with
silicon-isolation)
three spark plugs, made in Germany (water proof)
one rubber ring to protect the ignition cables
Ignition case W353/B1000
Prod.No. 6878
69,25
Complete aluminium Ignition case inkusive three lever contact breaker bas plate, ignition cam,
mounting cable and plastic cover for the Wartburg 353 and Barkas B1000 2-stroke engine.
original spare part
contact breaker: material plastic
Seite 59 from178
Ignition coil 12V, complete
Prod.No.
3161
19,90
Prod.No.
7053
34,50
ignition coil fit to all Wartburg 353 and Barkas 2-stroke
Ignition coil 12V, genuine part
Wartburg and Barkas ignition coil fro the German genuine producer.
The ignition coil fit to all Wartburg 353 and Barkas 2-stroke.
diameter: 40mm
length of the case: 90mm
made in Germany
Mounting screw for ignition base plate
Prod.No. 7718
1,10
Screw made of stainless steel slotted for mounting and adjusting of the ignition base plate for
Wartburg 312, 353, B1000 und boat engines.
Fit to contact braker or electronic ignition systems.
material: stainless steel
sensor for elektronic ignition box ( EBZA2f) -repair service-
Prod.No. 6174
35,70
to use with original Elektronic ignition box for EBZA2f for Wartburg 353 and Barkas (B1000) ? Two
stroke
also with Art.No. 6046)
original sensors with new electronic
only possible per exchange and first send in the defect sensor
Three-lever contact breaker base plate, complete
Prod.No.
3160
29,33
Ignition base plate complete with 3x contact breaker and 3x ignition capacitor
Fit to:
Wartburg 311
Wartburg 312
Wartburg 313
Wartburg 353
Barkas B1000 with 3 cylinder 2-stroke engine
Wire harness for ignition
Prod.No. 7436
14,59
Complete pree mounted wire set for the three-lever contact breaker ignition system of the Wartburg
353.
Wire colour: 1x green, 1x green-black, 1x green-red.
Inclusive protection hose, black.
One side will be mounted at the ingition interrupters and the other side at the ignition coils.
original spare partl
scope of delivery inclusive sealing for base plate case
only use for contact braker ignition systems.
Woodruff key for ignition case - timing shaft
Prod.No. 7486
0,45
Fitted key fit to all Wartburg 353 and Barkas B1000 2-stroke engines with contact breaker ignition or electronic ignition
EBZA.
Wartburg 353 > Spare parts > Engine > cylinder head
Seite 60 from178
Bolt for cylinder head
Prod.No.
6931
4,10
cylinder bols fit to:
Wartburg-353, 2-stroke, 3-cylinder,1000ccm or 1200ccm, 8 or 12 bolts
Wartburg-3112-stroke, 3-cylinder,900 or 1000ccm, 8 or 12 bolts
Barkas-B1000,2-stroke, 3-cylinder,1000ccm, 8 bolts
Framo 2-stroke, 3-cylinder 900ccm, 8 or 12 bolts
The tightening torque and the sequence of mounting of the cylinder head nuts you can find at (Details)
Cylinder head nut
Prod.No.
6318
1,88
cylinder head nut fit to:
Wartburg-353, 2-stroke, 3-cylinder,1000ccm or 1200ccm, 8 or 12 bolts
Wartburg-3112-stroke, 3-cylinder,900 or 1000ccm, 8 or 12 bolts
Barkas-B1000,2-stroke, 3-cylinder,1000ccm, 8 bolts
The tightening torque and the sequence of mounting of the cylinder head nuts you can find at (Details)
Cylinder head packing
Prod.No. 3120
8,99
Cylinder head packing is made of an special kind of sealing paper with dry graphite finish. The cylinder
are sealed by single metal-rings for each one, which are fixed at the paper packing.
Wartburg-353, 2-stroke, 3-cylinder, 1000ccm, 8 bolts
Barkas-B1000,2-stroke, 3-cylinder, 1000ccm, 8 bolts
The tightening torque and the sequence of mounting of the cylinder head nuts you can find at
Art.No.:6318
V-belt pulley, plastic W353
Prod.No.
6584
13,44
V-belt pulley for shaft of water pump (in cylinder head of Wartburg 353)
Wartburg 353 > Spare parts > gearbox
Seite 61 from178
ADDINOL gear box oil GS80W (GL60), 1 Litre
Prod.No.
6620
5,72
Prod.No.
6619
5,75
Prod.No.
6980
4,00
Prod.No.
7082
3,14
High-end-car-gearbox oil for Wartburg 353, Barkas B1000 and other vehicles
Made of german high-quality producer ADDINOL
for usability in countrys with central european weather (with a cold winter)
needed volume for one gearbox of Wartburg 353: 1,8 Litre
needed volume for one gearbox of Barkas B1000: 2,75 Litre
corresponds with the old name of viskosity: GL60 (SAE 80 EP)
SAE 80W; API GL-4; MIL-L-2105
homologations:
Mercedes-Benz 235.1
MAN 341
ZF TE-ML 02 A, 17A
application:
Hypoid gears with small offset
manual gear change-, steering- and distributing gear boxes
ADDINOL gear box oil GS80W90 (GL125), 1 Litre
High-end-car-gearbox oil for Wartburg 353 and others vehicles
Made of german high-quality producer ADDINOL
for usability in countrys with mediterranean or tropical weather
needed volume for one gearbox of Wartburg 353: 1,8 Litre
corresponds with the old name of viskosity: GL125 (SAE 90 EP)
SAE 80W-90; API GL-4; MIL-L-2105
application:
Hypoid gears with small offset
manual gear change-, steering- and distributing gear boxes
Ball joint for gear shifting
The Ball-pin is mounted on top of the gear change shaft.
Fit to all Wartburg 353 from vintage May 1986
Material: plastic
original spare part
Original number: 5301315801
ball ring for floor gear change mechanism
ball ring to use with stick shift mechanism
made of grey plastic
inner diamter of hole: 10,2 mm
biggest outer diamater: 21,6 mm
height: 12 mm
one piece will be needed for each gear change mechanism
Seite 62 from178
Ball socket for gear shift bar
Prod.No. 7434
3,29
Plastic ball socket for the gear shift bar of the gear shift mechanism inside steering column for
Wartburg 353.
To connect control lever of gearbox side with Selector rod of gear change mechanism
material: plastic
Bearing bush for floor gear change mechanism (W353)
Prod.No.
7083
12,50
Prod.No.
6767
17,41
Prod.No.
3110
12,20
Prod.No.
6981
5,83
Bearing bush to use with stick shift mechanism of Wartburg 353
This bearing bush will be held by rubber ring inside top cover.
One Collar for gear shifting shaft will be mounted on outer rim of this bush.
made of steel
length: 22 mm
diameter of hole: 12 mm
Cable for freewheel
Bowdencable for freewheel control on gearbox of Wartburg 353.
total length: 93 cm
lenght of the cover: 55,5 cm
original spare part
Cluch cable complete
Bowdencable with grease nipple for the Wartburg 353 cluch. Fit to all models.
total length: 55 cm
lenght of the cover: 29 cm
made in EU
Collar for gear shifting shaft
Sealing sleeve mounted on top of the gearbox to save the gear change shaft.
Fit to all Wartburg 311, 312, 313 and 353 without vintage limit.
Material: rubber
one piece will be needed for intake gear change shaft (all types)
two pieces will be needed for gear change mechanism of stick shift mechanism fit to Wartburg 353
original number: 53080001008
control lever of gear change mechanism
Prod.No.
control lever for gear shift mechanism inside steering column for Wartburg 353
7018
25,90
7393
2,54
delivery with sleeve rubber between control lever and gear casing
Prod.No.
Single part of the cylindrical roller for the freewheel of the Wartburg 353 (old and later type of gearboxes.
length: 14mm
made in Germany
Seite 63 from178
Flexible shaft for speedometer
Prod.No.
3500
9,89
Prod.No.
6389
53,50
Prod.No.
3144
95,00
Prod.No.
7295
74,20
Prod.No. 7041
complete gear shift bar for gear shift mechanism inside steering column for Wartburg 353
To connect control lever of gearbox side with Selector rod of gear change mechanism
delivery with plastic ball socket and rubber roller
12,50
Flexible shaft for speedometer fit to all Wartburg 353 and Wartburg 1,3.
total lenght of the shaft: 1170 mm
both ends are with tetrahedral tappet: 2,6 x 2,6 mm
connection screw joint: aluminium-nut
Freewheel cam with cylindric rolls
cam for freewheel for Wartburg gearbox up to vintage: november 1986.
Mounting without woodruff key.
original spare part
scope of delivery without cage and torsion spring
incl. 10 cylindric rolls
Freewheel crate complete, from 11-86
cam for freewheel for Wartburg gearbox from vintage: november 1986.
Mounting with woodruff key.
original spare part
scope of delivery inclusive cage, torsion spring and 10 cylindric rolls
Freewheel crate complete, up to 11-86
cam for freewheel for Wartburg gearbox up to vintage: november 1986.
Mounting without woodruff key.
made in Europe
scope of delivery inclusive cage, spring, 10x cylindrical roller
piece will be needed
Gear shift bar
Half of bearing bush
Prod.No.
One half of Bearing bush for gear shift column next to bearing bush for steering column
7061
3,11
7062
4,35
made of plastic
only fit to Wartburg 353 with steering column gear change
Half of bearing bush
Prod.No.
One half of bearing bush for gear shift column next to bearing bush for steering column
made of plastic
fit to Wartburg 353 with steering column gear change and stick shift
two pieces will be needed for control lever of gear change mechanism with steering column gear
change
four pieces will be needed for Wartburg 353 with stick shift (one pair for lower side of gear change
lever and another pair for backside bearing of gear change rod)
Seite 64 from178
Profile piece for rocking arm unit
Prod.No. 7079
6,77
Profile piece to mount at rocking arm fit to gear change mechanism of steering column gear change
made of plastic
Rocking arm unit from august 1986
Prod.No.
7078
28,89
Prod.No.
7435
28,89
Rocking arm fit to gear change mechanism of steering column gear change
Rocking arm unit up to august 1986
Rocking arm fit to gear change mechanism of steering column gear change
Rubber ring for floor gear change mechanism (W353)
Prod.No. 7084
Rubber ring to locate the bearing bush of stick to use with stick shift mechanism of Wartburg 353
7,91
made of black rubber
height: 10 mm
inner diameter (locator of bearing bush): ca. 20 mm
outer diamter: 42 mm
outer diameter of circumferetial slot: 34 mm
Rubber ring for gear shift bar
Prod.No. 7433
6,50
Single part of the complete gear shift bar for gear shift mechanism inside steering column for Wartburg
353.
The ring will be mounted inside of the eye of the bar.
Rubber roller for selector rod of gear change mechanism
Prod.No. 7085
Rubber roller fit to selector rod of steering column gear change mechanism of Wartburg 353
4,77
for both variants of selector rod (with ball joint made of plastic or steel)
height: 12 mm
outer diameter: 37 mm
smallest inner diameter of conical hole: 9,5 mm
genuine part IFA
Selector rod of gear change mechanism
Prod.No.
7022
26,47
Selector rod of gear change mechanism for Wartburg 353
delivery with rubber cap, gear shift lever with plastic ball joint (from May 1986 onwards) and rubber
roller
Shaft seal - gearbox final drive
Prod.No.
6532
10,83
Radial oel seal for the final drive Wartburg 353 gearbox.
size: 75 x 100 x 10
material: NBR (Nitril-rubber)
with additional dust lip
made in Germany
Seite 65 from178
Shaft seal - gearbox main shaft
Prod.No.
6531
4,52
Prod.No.
7002
8,77
Prod.No.
7341
52,43
Prod.No.
7340
52,43
Prod.No.
sleeve for clutch cable of Wartburg 353 (2-stroke) and Wartburg 1.3 (4-stroke)
6370
8,80
6776
4,60
Radial oel seal for the clutch shaft Wartburg 353 gearbox.
size: D24 x 40 x 7
made in Germany
Shaft seal - universal shaft
Radial oel seal for wheel side he drive Wartburg 353 gearbox.
size: 45 x 60 x 7
made in Germany
two pieces will be needed (one for each drive shaft)
shaft spider for transmission shaft, W353, new type
Complete spare part shaft spider for the Wartburg 353 drive shaft, from to vintage May 1986
Right and left side mountable.
Teeth at the drive shaft: 22
diameter spiderring: 27mm
diameter spider: about 66mm
For each universal shaft one piece will be needed
length of the tooth piece: 35mm
original spare part
shaft spider for transmission shaft, W353, old type
Complete spare part shaft spider for the Wartburg 353 drive shaft, up to vintage May 1986
Teeth at the drive shaft: 22
diameter spiderring: 27mm
diameter spider: about 66mm
For each universal shaft one piece will be needed
length of the tooth piece: 25,5mm
original spare part
sleeve for cluch cable
length: 90mm
lenght (short): ca. 55mm
inner diameter big: 12mm
inner diameter small: ca. 6mm
Subject to availability (no regular range)!
sleeve for control lever of gear change mechanism
Prod.No.
sleeve rubber between control lever and gear casing inside steering column
Seite 66 from178
sleeve for floor gear change mechanism
Prod.No.
6387
5,60
Prod.No.
3148
6,50
Prod.No.
3147
4,20
Prod.No.
7680
1,95
Prod.No.
7453
9,50
Prod.No.
6865
15,50
Prod.No.
7542
135,00
sleeve for floor gear change mechanism
Sleeve rubber ( inner side )
Rubber sleeve gearbox side for the right and left universal shaft.
Fit for all universal shaft of the Wartburg 353 and Wartburg 312
best quality, made in Europe
delivery as an single part without mounting spring and mounting strap
Sleeve rubber ( outer universal shaft side )
For each drive shaft two pieces will be needed.
This oel (Art.-Nr.:6619) have to be used for the lubication of the outer joint.
made in EU
additional mounting part band clamp-set
Snap ring sleeve rubber final drive
Circlip for mounting at the Wartburg 353 and Wartburg 1,3 drive shaft boot.
Can be used at the inner sleeve of the outside joint.
Two piece will be needed for each car.
Steering column packing
Rubber seal for the Wartburg 353 steering column.
Fit to cars with steering column gear change.
without mounting parts
original spare part
Tapered roller bearing 3308 D
Two row grooved ball bearing, fit to the Wartburg 353 gearbox:
1x for bevel gear shaft
mark: 3308
TNG TGL 2982
outside diameter: 90mm
inside diameter:40mm
width: 36,5mm
made by: DKF (DDR)
1x Tapered roller bearings will be needed
Transmission shaft, W353 secound hand part
Dirve shaft Wartburg 353 as an checked extension element.
Scope of delivery inclusive spider.
Please choose at the window the car vintage.
Seite 67 from178
Transmission suspension gear box
Prod.No.
7049
15,98
Prod.No.
Outher wheel bearing for the front and rear axle of Wartburg 353 und Wartburg 1,3
3320
13,50
3325
17,32
3300
15,20
Rubber spring for gearbox Wartburg 353
one side with mounting nuts and the other side with drill hole.
ZAK No. 1464411253682640
Wartburg 353 > Spare parts > Front axle
Ball bearing 6009 C2
one piece needed for each wheel
mad in Germany
Ball bearing 6307 C2
Prod.No.
Outher wheel bearing for the front rear axle of Wartburg 353 und Wartburg 1,3
one piece needed for each wheel
mad in Germany
Ball joint for trak rod, complete
Prod.No.
The ball joint fit to Wartburg 353 and 1,3
made in Europe
Ball joint for wishbone, complete
Prod.No. 3302
24,74
Connection ball joint for the other wishbone and and the swivel bearing. fit to all Wartburg 312, 353
und 1,3 models. The joint is mounted at the upper and the bottom wishbone.
delivery inclusive sealing cap
for each wheel side two pieces will be needed
Bearing for steering column
Prod.No.
7059
3,28
Bearing bush for steering column
made of plastic
fit to all chassis variants of Wartburg 353 and Wartburg 1,3
Coil spring retainer for wishbone W353 /312
Prod.No. 7659
22,61
Lower suspension spring support for the front axle of the Wartburg 353 and 312.
The spring cup seat have to be mounted together with the shock absorber holder on top of the upper
wishbone Wartburg 353 / 312. Fit at the front axle left and right hand.
surface: steel blank
for each car two pieces will be needed
good reporduction, made in Eu
Seite 68 from178
Driver for steering column
Prod.No. 7244
1,90
Steel driver for fabric joint for the connection of the steering column of the 353 und Wartburg 1.3 to the
Steering column assembley.
sheet metal, galvaniced
two pieces will be needed for each car
made in Germany
Fabric washer, steering column
Prod.No. 7068
Rubber joint for the connection of the steering column of the 353 und Wartburg 1.3 to the Steering column assembley.
9,82
delivery inclusive 8 pieces of tubular rivet to reinforce the hole
one piece will be needed for each car
made in EU
Gas pressure telescopic shock absorber, W353, front axle
Prod.No. 7238
68,00
Two pipe gaspressure buffer for the Wartburg 353 front axle with coil spring. Fit to both typs:
Limousine and Tourist from vintage: 1965 up to 1988.
mounting eye on both ends
lenght total: 44cm (eye-eye)
length pressed: 28cm (Auge-Auge)
made in Japan
Hub cap , plastic
Prod.No.
Plastic cover for the inner hole of Wartburg wheel disk to cover the hub axle nut.
7042
3,23
material: plastic, black
made in EU
for each wheel one piece will be needed
Locking plate for ball joint for wishbone
Prod.No. 7003
1,89
Locking plate for both outer mounting screws of ball joint for the other wishbone and and the swivel
bearing. fit to all Wartburg 312, 353 und 1,3 models.
The joint is mounted at the upper and the bottom wishbone.
for each ball joint one piece will be needed
Look plate ball joint for trak rod
Prod.No.
7240
1,49
Look plate to secure the mounting connetion between ball joint and track rod.
Fit to Wartburg 353 and 1,3
total two pieces will be needed
made in Germany
Seite 69 from178
Metal bushing for buffer bearing bush of wishbone
Prod.No.
Metall bushing to use in tandem with rubber for buffer bearing bush
Fit to all chassis arms of Wartburg 353 (new type of bearing bush)
Also fit to older types of bearing bushes if carry on using outer metal bushing of that.
6813
3,90
upper wishbone, front axle - 2 pieces for each wishbone
lower wishbone, front axle - 2 pieces for each wishbone
wishbone, rear axle - 2 pieces for each wishbone
summary:
front axle: in all 8 pieces
rear axle: in all 4 pieces
Mounting nut for ball joint
Prod.No. 7716
2,23
Nut for the connection ball joint for the other wishbone and and the swivel bearing. Fit to all Wartburg
312, 353 und 1,3 models. The nut can be used for the upper and the bottom wishbone.
delivery inclusive spring washer
four pieces will be needed
Nut for track rod M12, right tap
Prod.No.
7241
0,99
Trak rod nut for mounting at the connection between clamping nut - ball joint.
Fit to all Wartburg 353 and 1.3
surface: galvanized
thread M14x1,5 right
spanner gap SW19
for each car two pieces will be needed
made in Germany
Radial sealing 55 x 75 x 10 SL
Prod.No. 3330
10,92
Sealing with additional dust lip to protect the sealing lip to protect the wheel bearings at the front and
rear axle.
material: NBR black
made in Germany
for the front axle 2 pieces and for the rear axle 2 pieces will be needed
Fit to the models: Wartburg 312, wartburg 353 und Wartburg 1,3
Rubber for buffer bearing bush of wishbone
Prod.No.
Rubber bushing to use in tandem with metal bushing for buffer bearing bush
Fit to all chassis arms of Wartburg 353 (new type of bearing bush)
Also fit to older types of bearing bushes if carry on using outer metal bushing of that.
6812
5,90
summary:
Seite 70 from178
Silent buffer bush for wishbone
Prod.No.
6372
11,05
Prod.No.
938
replacement sleeve for ball joint. Fit to Trabant601, Trabant 1,1 and Wartburg 353 and 1,3.
2,60
Silentbuffer bush fit to all chassis arms of Wartburg 353
Fit ot diameter 26mm.
summary:
Sleeve for ball joint
It is only recommendable if ball joint is without any slackness
sleeve for ball joint of wishbone
Prod.No. 6371
4,78
replacement sleeve for ball joint of wishbone
fit to all types of Wartburg 353 and 1.3
[one piece needed for each ball joint (2 pieces for each front axle side)][material: rubber][made in EU]}
Spring W353, front axle
Prod.No. 7323
Coil spring for the Wartburg 353 front axle. Fit to both typs: Limousine and Tourist from vintage: 1965 up to 1988.
55,00
length of the spring: original (lo=418mm)
made in Germany
Steering rack gaiter (W353 from Jan.87 / W1.3)
Prod.No. 7023
5,40
This gaiter for steering fits to Wartburg 353 (from January 1987 onwards) and all kind of Wartburg 1,3.
delivery without mounting parts
Steering rack gaiter (W312/W353 up to Dec.86)
Prod.No.
This gaiter for steering fits to Wartburg models 312 and 353 up to December 1986.
3315
17,50
Telescopic shock absorber, W353, front axle
Prod.No. 6062
38,40
Buffer for the Wartburg 353 front axle with coil spring. Fit to both typs: Limousine and Tourist from
vintage: 1965 up to 1988.
made in Germany
Seite 71 from178
Wheel bearing set
Prod.No.
7242
53,75
Prod.No.
7109
99,50
Prod.No.
7020
6,43
Wheel bearing set for the front and rear axle of the Wartburg 353 and 1,3.
Ser consist of:
1x deep groove ball bearing:6009 C2
1x deep groove ball bearing:6307 C2
1x sealing ring
1x bearing grease
made by FAG
made in Germany
for each car 4 sets will be needed
Wheel hub, secound hand
Wheel hub for the Wartburg 353. Fit to the front and the rear axle.
Wartburg 353 > Spare parts > rear axle
Rubber lid for trailing arm, rear axle (W353/W1.3)
Black rubber washer to seal the inner side of wheel carier
Fit to rear axle of Wartburg 353 and 1.3
Rubber spring for end stop wishbone (W353/W1.3)
Prod.No. 7056
6,11
Black rubber spring for upper end stop of wishbone rear axle (wartburg 353 and 1.3) and for upper
wishbone of front axle Wartburg 353 (maybe for Wartburg 1.3, too)
four pieces will be needed for complete rear axle of Wartburg 353 and 1,3
two pieces will be needed for both upper wishbones of Wartburg 353 front axle
Shim washer (rubber)
Prod.No.
7008
8,68
Prod.No.
6705
38,40
Prod.No.
6065
52,50
Shim rubber made of black rubber
to be mounted between outer ring of inner wheel bearing and wheel hub
Fit to rear axle of Wartburg 353 and 1.3
Shock absorber for rear axle W353
Buffer for coil spring for the rear axle.
Fit to Wartburg 353 limousine and estate car.
from vintage 1965-1988
made in Germany
Spring for rear axle (Tourist, Camping)
Coil spring for the rear axle of car body variante: estate car
Fit to Wartburg 353 and 1,3 Tourist and Wartburg 312 Camping.
size: midle diameter of the coil: 111 mm, total lenght of the unencumbered spring: 350 mm, wire diameter: 15mm,
count of coils: 8,5
made in Germany
Seite 72 from178
Spring for rear axle (Tourist, Camping) 20% bonded
Prod.No.
6689
64,88
Spezial produced coil spring for the rear axle of car body variante: estate car
Fit to Wartburg 353 and 1,3 Tourist and Wartburg 312 Camping.
size: midle diameter of the coil: 111 mm, total lenght of the unencumbered spring: 355 mm, wire diameter: 16
mm, count of coils: 8
made in Germany
Spring for rear axle W353,W32 (Limousine)
Prod.No.
7665
52,86
Coil spring for the rear axle of car body variante: limousine
Fit to Wartburg 353 and Wartburg 312.
size: midle diameter of the coil: 112 mm, total lenght of the unencumbered spring: 373 mm, wire diameter: 14mm, count of
coils: 8,5
made in Germany
Wartburg 353 > Spare parts > car body parts
Buffer car body
Prod.No. 7424
6,80
Rubber buffer to connect the car body at the frame (chassis) of the Wartburg 353 and Wartburg 1.3.
Mounting place: front, middle and rear fixing point.
for each car 10 pieces will be needed
material: rubber
colour: black
diamter big: 42mm
diameter small: 23m
length of the step: 11mm
total length: 29mm
Cable control for bonnet look
Prod.No.
3505
11,27
Prod.No.
7093
1,88
Prod.No.
7260
9,86
Prod.No.
3535
18,96
Bowdencable for unlock engine bonnet Wartburg 353 and Wartburg 1,3
Made in germany.
length: 1800mm
coiled spring pin for door hinge
coiled spring pin for all hinges of side doors of Wartburg 353 and 1.3
two coiled spring pins will be needed for each door (two hinges)
length: 60mm
Mudflaps rear Wartburg
One paar of dirt traps for the monting at the rear wheel housing.
Fit to the cars Wartburg 353 and Wartburg 1.3.
colour: black
material: rubber
scope of delivery one set (two pieces)
made in EU
Outer rear view mirror, left
Seite 73 from178
Outer rear view mirror, right
Prod.No.
3540
18,96
pedal shaft
Prod.No. 7554
23,50
Shaft for the brake pedal and clutch pedal. The pin is mounted at the frame driver side front left hand,
and have to be fixed with two snap rings.
Scope of delivery inclusive four plastic joint bushes for the pedal eye, two snap rings and grease
nipple.
Fit to Wartburg 353 and Wartburg 1.3
One piece will be needed.
Made in EU.
Profile for external door-duct
Prod.No.
Profile for external door-duct weather strip. Complete for all doors leng 16 meter.
Fit to Wartburg 353 also for door of camper Intercamp available
6051
83,20
7423
8,50
material: sponge rubber
colour: black
made in Germany
Retainer for car body W353
Prod.No.
Support holder to connect the car body at the frame (chassis) of the Wartburg 353.
Mounting place: middle of the cassis front and rear fixing point.
for each car four pieces will be needed
material: steel
surface: galvaniced
Ring car body
Prod.No. 7425
Rubber ring to connect the car body at the frame (chassis) of the Wartburg 353 and Wartburg 1.3.
Mounting place: front, middle and rear fixing point.
4,90
material: rubber
colour: black
inside diameter: 24m
thickness: 10,5mm
rubber buffer for bonnet and luggage compartment lid
Prod.No. 6567
rubber buffer for bonnet and luggage compartment lid of Wartburg 353 and Wartburg 1.3
colour: black
follow pieces will be needed:
4,94
bonnet W353: 4 pieces
luggage compartment lid W353: 2 pieces
bonnet W1.3: 4 pieces
luggage compartment lid W1.3: 2 pieces
no original spare part
Seite 74 from178
Rubber cover for pedal
Prod.No.
7021
1,96
Prod.No.
6673
22,62
Rubber cover fit to brake pedal and clutch pedal
Fit to Wartburg 353 and Wartburg 1.3, too.
for each pedal fou will need one piece
material: soft rubber
colour: black
Rubber profile for sunshine roof
Sealing rubber for Wartburg 353 and 1,3 sliding roof.
length: 2,25 m
material: rubber
colour: black
made in Germany
Wartburg 353 > Spare parts > Panes & rubber sections
edge protection, front doors
Prod.No. 6014
11,41
edge protection for sheet metall fold on inner side of doorway of driver and co-driver door (fold will be used as end stop of
front door)
The edge protection is to mount on the right, left (A- and B-pillar) and upper side of doorway.
Length: 2610mm (information according to spare parts catalogue)
colour: black
we will deliver one piece of 2,70m
edge protection, rear door
Prod.No. 6013
Edge protection for sheet metall fold on inner side of doorway of rear doors (fold will be used as end stop of front door)
The edge protection is to mount on the right, left (C- and B-pillar) and upper side of doorway.
11,55
Length: 2740mm (information according to spare parts catalogue)
colour: black
we will deliver one piece of 2,80m
Metal holder for water bottle
Prod.No. 7442
3,50
Metal retainer for the windscreen water bottles 1,5 liter of the Trabant, Muticar, B1000 and 2,5 liter of
the Wartburg models.
original spare part
material: steel, surface galvaniced
Profile filler rear window of Limousine
Prod.No.
profile filler for rubber section rear window (only for car body variant Limousine)
6642
20,40
fit to Wartburg 353 and Wartburg 1,3
Available in three different colours: black, white and grey (Please chose the wanted colour below!).
length 3,40m (original length: 323,5 cm)
Seite 75 from178
Profile filler rear window of Limousine
Prod.No.
7676
24,00
profile filler for rubber section rear window (only for car body variant Tourist)
length: 4,00m
Profile filler rear window of Trans
Prod.No. 6676
profile filler for rubber section rear window (only for pick-up car body variant, called Trans)
11,67
length 1,80m (original length: 163 cm)
Profile filler silver (chrome effect)
Prod.No.
6049
12,15
profile filler for many rubber section of Wartburg 353 and Wartburg 1,3
rubber section of windscreen, fit to all car body variants: Limousine, Tourist and Trans (original length:
3445 mm)
fit to rubber section rear window of car body variant Limousine (original length: 3235 mm)
fit to rubber section rear window of pick-up variant, called Trans (original length: 1630mm)
fit to rubber section rear window of car body variant Tourist (4000 mm)
Chromed style (colourless plastic with integrated chrome tape)
Length 3,60 meter, 3,40 meter or 1,80 meter, depending on type of rubber section (Please chose if
you need:
the filler for rubber section of windsreen (length 3,60m),
the filler for rubber section rear window of Limousine (length 3,40m) or
the filler for rubber section rear window of Wartburg Trans (length 1,80m)or
the filler for rubber section rear window of Tourist (length 4,00m)
Profile filler windscreen
Prod.No.
profile filler for rubber section windscreen fit to Wartburg 353 and Wartburg 1,3
fit to all car body variants: Limousine, Tourist and Trans.
6050
21,60
available in three different colours: black, white and grey (Please chose the wanted colour below!).
Length 3,60 meter
rotary switch for wiper motor W353 / B1000
Prod.No.
6576
7,94
switch for wiper motor with terminal for water pump
fit to Wartburg 353 and B1000
fit to 6V and 12V voltage
boss included
two switching positions
without timer switch position
Seite 76 from178
Rubber-section for rear window (tailgate), Tourist (W353)
Prod.No. 6786
39,38
Rubbersection for the rear window inside tailgate. Fit to Wartburg 353 (NOT for wartburg 1,3). Only for
car body variant called Tourist (estate car/ station wagon).
Screenrubber profile type for available profile filler or profile filler chrome effect).
scope of delivery without filler
lenght: 3m (price per piece)
Rubber-section for rear window, Limousine (W353 / W1.3)
Prod.No. 6048
Rubbersection for the rear window. Fit to Wartburg 353 Limousine and 1,3 Limousine and Trans.
36,90
lenght: 3,40 meter
made in Germany
Rubber-section for rear window, Trans (W353 / W1.3)
Prod.No. 6674
Rubbersection for the rear window. Fit to Wartburg 353 and 1,3 Trans (Pick-up version).
19,78
lenght: 1,80 meter (original length: 1,60m)
made in Germany
Rubber-section for windscreen (W353/W1.3)
Prod.No.
6047
36,94
Prod.No.
3215
33,56
Rubbersection for windscreen. Fit to Wartburg 353 and Wartburg 1,3.
rubber-section profile type for profile filler or profile filler chrome effect.
lenght: 3,40 meter
made in Germany
Tank for windscreen washer
Plastic reservoir for windscreen washer.
inclusive accessory
new type form year 5-85
Weather strip bottom plate - doors
Prod.No. 6641
26,19
sealing rubber section between bottom plate (frame side member) and side doors
The weather strip will be mounted along the frame side meber on bottom side of entrance edge. It is
an additional sealing against spray water in area under the doors.
fit to car body variants: Limousine and Tourist
length: 1,58m
two pieces needed for one car (one for every side)
For car body variant Wartburg Trans (Pick-up) the same rubber section will be needed but the length
is not the same (length unknown).
Weather strip for luggage compartment
Prod.No.
3220
27,04
only for car body variante: Limousine
Seite 77 from178
Windscreen ( MSG ), colourless
Prod.No.
3197
193,00
Prod.No.
3198
193,00
Prod.No.
3199
193,00
windscreen clear like original.
sorry no shipping possible
Windscreen ( MSG ), with sunshild blue
windscreen with 50mm wide sunshild blue on top.
Windscreen ( MSG ), with sunshild green
windscreen with 50mm wide sunshild green on top.
Windscreen wiper Tourist
Prod.No. 6625
12,50
Rear windshild wiper complete with wiper arm and wiper blade. Arm complete with tension spring and
clamping sleeve for fixing
lenght of the arm: 300mm
lenght of the wiper blade: 330mm
original spare part
fit to W353 and W1,3
one will be needed
Wiper arm new version
Prod.No.
3210
6,92
Prod.No.
7496
6,92
wiper arm complete with tension spring and clamping sleeve for fixing
Version for pinned the wiper blade.
lenght: 300mm
Wiper arm old version
Wiper arm complete with tension spring and clamping sleeve for fixing
Version with hock to clip in the wiper blade.
lenght: 360mm
Wiper blade chrome
Prod.No. 6935
6,95
Original wiper blade made of stainless steeel complete with 2 leading spring arms, wiper rubber and fixing plug for wiper
holder.
length: 415mm
fit to all W353 and W1,3 models
Wiper blade rubber
Prod.No. 6626
Rubber section for wiper blade, single part.Scope of delivery without fixing metal holder.
3,00
length: 415mm
original spare part
Seite 78 from178
Wiper blade, new version
Prod.No. 3205
wiper blade complete with 3 leading spring arms, wiper rubber and fixing plug for wiper holder.
latest version of the wiper blade, it will be pinned at the wiper arm.
6,50
length: 415mm
Wiper blade, old version
Prod.No. 7495
wiper blade complete with 3 leading spring arms, wiper rubber and fixing plug for wiper holder.
Old version of the wiper blade, it will be mounted by an hock at the wiper arm.
6,50
length: 415mm
Wiper linkage
Prod.No.
3200
49,99
Prod.No.
1264
19,20
The wiper linkage is a complete mounted component.
fit to all Wartburg 353 and Wartburg 1,3
Wartburg 353 > Spare parts > Accessories
Inner rear view mirror Wartburg
Panorama mirror for the Wartburg 353 and 1.3 indoor.
The spare part is original made in Germany.
lenght: 24,5 cm
wide: 7 cm
inckusive plastic feet for mounting at the roof fram
Rubber carpet front, black W353 steering gear shifting
Prod.No. 7368
65,00
Elaborate made and exactly cuted carped with cloth edge for the Wartburg 353 limousine and tourist
types with gearshifting at the steering column.
The rubber carpet will be inserted in front of the front seats to prove the original carpet against mud
and moisture form the passengers shoes.
material: corrugated rubber, with nonslip bottom and fringe
made in Germany
Rubber carpet front, black W353 stick shift
Prod.No. 7369
65,00
Elaborate made and exactly cuted carped with cloth edge for the Wartburg 353 limousine and tourist types with gearshifting
stick shift.
The rubber carpet will be inserted in front of the front seats to prove the original carpet against mud and moisture form the
passengers shoes.
material: corrugated rubber, with nonslip bottom and fringe
made in Germany
Trademark * 353W *
Prod.No.
3551
2,99
Trademark * IFA WARTBURG*
Prod.No.
3550
3,17
Trademark * TOURIST *
Prod.No.
3552
2,98
Wartburg 353 > Spare parts > Accessories > valve caps
Seite 79 from178
Wartburg 353 > Tuning parts
Wartburg 353 > Tuning parts > Revolution counter
Wartburg 353 > Tuning parts > Electrical system
Ignition look (second hand) W353
Prod.No.
7280
59,23
Complete unit with key switch for ignition and starter (with key)
Fit to all Wartburg 353.
Wartburg 353 > Tuning parts > harness belts
Wartburg 353 > Tuning parts > Suspension
Telescopic shock absorber front axle 60mm shorter
Prod.No. 7065
These tuning shock absorbers are 60 mm shorter than the original part and more tautly. Fit to Wartburg 353 front axle.
Excellent for decent styling.
59,00
made in Germany
Telescopic shock absorber rear axle 30mm shorter
Prod.No. 6572
46,07
These tuning shock absorbers are 30 mm shorter than the original part and more tautly. Fit to
Wartburg 353 rear axle with coil spring.
made in Germany
The schock absorber for rear axle have the same dimensions like the shock absorber for the front
axle, but they are NOT compatible (interchangeable) because they a have different setting!
The shock absorber for rear axle are marked (by label).
Prod.No. 7064
48,20
Wartburg 353 and Wartburg 1,3 rear axle with coil spring.
made in Germany
Prod.No. 7088
54,00
Wartburg 353 rear axle with coil spring.
made in Germany
The schock absorber for rear axle have the same dimensions like the shock absorber for the front
axle, but they are NOT compatible (interchangeable) because they a have different setting!
The shock absorber for rear axle are marked (by label).
Seite 80 from178
Telescopic shock absorber for laef spring, 30mm shorter
Prod.No. 6570
46,07
Wartburg 353 front axle.
made in Germany
Telescopic shock absorber for laef spring, 40mm shorter
Prod.No. 7090
49,50
Wartburg 353 front axle.
made in Germany
Tuning coil spring, front axle
Prod.No.
6573
43,33
Coil spring for Wartburg 353 front axle. The sping will be 1,5 whorls shorted.
No desposit possible, the spings have to be first shipped to our company and then we will return you the new one
price for each one
Wartburg 353 > Tuning parts > Roll bar
Wartburg 353 > Tuning parts > roll cage
roll-cage with diagonal strut, steel tube
Prod.No.
7254
507,00
roll-cage with struts to the rear wheel houses and diagonal strut
material: steel tube St.52
main bars: steel tube 40 X 2 mmm
all other struts: steel tube 40 X 2 mm
A-main bar in front of dashboard
diagonal strut (vom upper left to lower right
surface: not varnished (sheer metall)
Also for other car types/models of Automobile availeble! (z.B. Audi, BMW, Ford, Opel und VW) Don't
hesistate to ask!
No shipping possible!
Wartburg 353 > Tuning parts > roll cage > in front of dashboard
Wartburg 353 > Tuning parts > carburettor
BING carburettor type 84
Prod.No.
6583
132,00
tuning carburettor made by BING in Germany
Type 84
Cross-draught slide carburettor with part-load needle jet control and idling system.
Starting carburettor with the housing made in aluminium (light weight).
bore size: 30 mm (by request also with a bore size of 28 mm and 32 mm)
Mounting on the engine by a clamped connection (by request also with push-on connection)
Wartburg 353 > Tuning parts > valve caps
Wartburg 1.3
Seite 81 from178
Wartburg 1.3 > Spare parts
Wartburg 1.3 > Spare parts > Exhaust system
Connection - pipe W1.3
Prod.No.
3022
30,34
Prod.No.
3019
53,64
Prod.No.
Exhaust flue for Wartburg 1,3 with double waste gas guiding up to the Y-branch pipe.
3024
39,38
Exhaust connection pipe between pre silencer and after muffler.
delivery without mounting bits
made in EU
Exhaust aftermuffler W1.3
Exhaust aftermuffler for the Wartburg 1,3 liter four cylinder engine.
made in EU
Exhaust pipe
material: metal pipe
made in EU
Gasket for exhaust double pipe
Prod.No. 6348
5,50
high quality and dimension accuracy gasket for the connection between exhaust mainfold and exhaust
double pipe
inclusive metal compress ring
made in Germany
Gasket for exhaust pipe
Prod.No. 3023
4,89
Exhaust gasket with middling quality for the connection between exhaust mainfold and exhaust double
pipe
inclusive metal compress ring
made in Hungary
Pre-silencer for katalysator
Prod.No. 3021
83,00
Exhaust pre silencer with connection flange for the unregulated catalytic converter Wartburg 1,3 liter
4-stroke engine.
delivery without catalytic converter and mounting bits
made in EU
Pre-silencer W1.3
Prod.No.
3020
69,37
Exhaust pre silencer for the Wartburg 1,3 liter four cylinder engine.
made in EU
Wartburg 1.3 > Spare parts > Brakes
Seite 82 from178
Prod.No.
6687
4,30
Prod.No.
6688
4,30
Lenght: 270mm
Lenght: 330mm
Wartburg 1.3 > Spare parts > Brakes > Brake line
brake line set, complete W1,3
Prod.No. 7265
42,24
Complete brake pipe set made of copper.
Brilliant exchange for old steel lines. Easy to mount, the bending can be done by hand without much
pressure. The set comes with outhlet nuts and complete flanged.
scope of delivery: one set
beanded with nuts
fit to Wartburg Wartburg 1,3 Limousine, Tourist, Tramp
made in EU
brake line, front, center, right (B-circle)
(W1.3)
Prod.No.
6695
7,88
brake line front middle right fit to Wartburg 1.3 (4-stroke)
This brake line connect the front terminal of brake master cylinder with posterior brake distributor
(B-circle).
Wartburg 1.3 > Spare parts > Brakes > Front brake
Brake hose, front 350 mm W1.3
Prod.No. 3097
Two pieces needed for each brake suddle of Wartburg 1,3 (four pieces for the complete front axle).
5,49
One piece will be needed for each brake suddle of Warburg Wartburg 1.3 (4-stroke)(A-circular)
The second Wartburg brake hosefor the brake suddle has a length of 303 mm and is also available
Wartburg 1.3 > Spare parts > Brakes > Rear brake
Brake drum 30mm
Prod.No. 3084
56,02
brake drums fit to Wartburg 353 models with disk brake system at the front axle and to all kind of
Wartburg 1,3.
The brake drum belongs to brake shoes with the wide of 30mm.
Wartburg 1.3 > Spare parts > Electrical system
cable for positive pole of car battery W1,3
Prod.No. 7426
28,45
connection cable between positive pole of car battery and the terminal screw of starter of the Wartburg
1.3
pre-finished
one cable tail with battery pole terminal
one cable tail with 8mm cable shoe for terminal screw of solenoid switch (mounted on starter)
thick and robust isolation (outer diameter: 13,3mm
new made in Germany
Seite 83 from178
Combi-instrument
Prod.No.
7354
35,90
Prod.No.
6422
15,24
Prod.No.
7719
12,51
Prod.No.
6045
19,90
Round instrument for the cars Wartburg 1,3 and B1000-1.
Original spare part for display the engine temperature and the fuel gauge.
type:
late type with LED
inclusive connection plug
power 12V
scope of delivery inclusive without bulbs
front rim : black
mounting diameter: 100mm
genuine spare part
Zak No: 3.085101/47
interval relais for windsreen wiper
interval relais for windsreen wiper
for yellow connector (6 pin)
switch unit for ignition look switch
Switch insert for ignition look.
Electrical part of ignition look switch wich is mounted at the backside.
Latest version with six blad terminals.
Best quality form the original manufacture made in Germany.
Fit to Wartburg 353, 1.3, Barkas B1000 and B1000-1
Wartburg 1.3 > Spare parts > Electrical system > Lighting
Direction indicator lamp
Mudguard (wing) indicator lamp fit to right and left hand Wartburg 1,3.
Delivery without bulbs
original spare part
Direction indicator lamp left, orange
Prod.No. 7226
35,00
Original indicator lamp for Wartburg 1,3. Mounting place radiator grill - mudguard front left hand
(driver side)
Delivery without bulbs.
original no: 8580.31/3L (1366554103920637)
original spare part
Direction indicator lamp right, orange
Prod.No. 7225
35,00
Original indicator lamp for Wartburg 1,3. Mounting place radiator grill - mudguard front right hand
(codriver side)
Delivery without bulbs.
original no:8580.31/2R (1366554103920629)
original spare part
Seite 84 from178
Direction indicator lamp, front, left hand ( white )
Prod.No.
3048
59,00
Prod.No.
3049
59,00
Prod.No.
(W1.3)
Lamp for rear number plate, mounted on top of rear bumper bar of Wartburg 1,3.
6720
16,84
6495
51,05
Prod.No. 6719
(W1.3)
Tail light with back-, brake- and indicator light and light for reverse fit to the left of Wartburg 1,3.
34,99
Directon indicator lamp for Wartbur 1,3 with clear lense front left side.
Direction indicator lamp, front, right hand ( white )
Directon indicator lamp for Wartbur 1,3 with clear lense front right side.
Lamp for rear number plate
Case made of black plastic
Delivery without light bulb
Original spare part
Two pieces will be needed for one car
steering column switch (W1.3)
Prod.No.
switch unit for steering column of Wartburg 1.3with follow switch-functionsLeft lever:
direction indicator
horn
headlamp flasher
turn up/down the headlights
Right lever:
windscreen wipers
windscreen washer pump
Tail light, left hand
with six mounting bolts and rubber sealing
Delivery without lamp sockets and light bulbs
original spare part
Tail light, right hand
Prod.No. 7227
(W1.3)
Tail light with back-, brake- and indicator light and light for reverse fit to the right side (codriver) of Wartburg 1,3.
34,99
with six mounting bolts and rubber sealing
Delivery without lamp sockets and light bulbs
original spare part
Wartburg 1.3 > Spare parts > Engine
Seite 85 from178
Carburettor bowdencable
Prod.No.
3515
7,37
Bowdencable fir to all Wartburg 1,3
length total: 125 cm
length of the vover: 102,5cm
made in the EU
intake connection for carburettor
Prod.No. 1246
32,05
The input pipe deflect the fresh air into the carburettor of 4-stroke version of Trabant (carburettor type:
32 F 1-1)
and Wartburg (carburettor type: 34 TLA 51/2)
material: black rubber
original spare part
delivery incluive connection for under-inflation pipes , controler w/c air
Key rubber spring (front engine bearing W1.3)
Prod.No. 7005
Key rubber spring to mount between support on frontside (left) of combustion engine and frame.
27,90
one piece will be needed for one Wartburg 1.3
Wartburg 1.3 > Spare parts > Engine > cooling system
blow off valve for compensating reservoir, 130kPa (W1.3/B1000-1) Prod.No.
618
12,22
Pressure valve for cooling water reservoir of Wartburg 1.3 and 4-stroke version of Barkas (B1000-1).
[pressure: 130kPa][to mount inside the reservoir cap][one piece will be needed]}
bottle for coolant (W1.3/B1000-1)
Prod.No.
6419
52,47
Prod.No.
3170
149,00
Prod.No.
Self repair set of pipes for the thermostat case of the Trabant 1,1 and Wartburg 1,3.
Set consist of:
7452
38,52
fit to Wartburg 1.3 and Barkas B1000-1 (both 4-stroke)
Radiator
Water coolant radiatior for the Wartburg 1,3.
material: Aluminium
made in EU
Repair set thermostat housing
2x tube with diameter 20mm
Seite 86 from178
Sealing ring for cooling water pipe
Prod.No.
Rubber seal for the connection between water pipe and engine block water pump.
Fit to the cooling system of the Trabant 1.1, Wartburg 1.3 and B1000-1.
7419
1,49
Sealing ring for Thermostat housing
Prod.No.
7418
1,49
Prod.No.
3530
49,88
Rubber seal for the connection between thermostat case and engine block.
Fit to the cooling system of the Trabant 1.1, Wartburg 1.3 and B1000-1.
tap for radiator
Roller valve to adjust the hot water for the passenger heating system at the heat exchanger.
Thermostat housing
Prod.No. 6448
39,83
The thermostat case is the centrally part of cooling system.
Both cooling loops are connected in the thermostat housing.
Depending on the engine temperature the thermostat opens the large cooling loop (through the
radiator).
original spare part
Wartburg 1.3 > Spare parts > Engine > clutch system
Cluch cable complete (W1.3)
Prod.No.
3111
10,31
Prod.No.
3103
93,60
Prod.No. 6561
+40,00? deposit
179,50
bowden cable for slip ring disengager of clutch
length total: 69 cm
length of cable hull: 47,5 cm
made in Euope
Clutch
W1.3
+30? deposit
clutch (pressure plate with disk spring)
only fit to Wartburg 1.3 (4-stroke engine from VW)
Please note the informations about the deposit (see details.
Clutch set W1.3
This clutch set fits to all variants of Wartburg 1.3 (with 4-stroke engine).content:
180mm clutch
release bearing
Disengaging shaft ( for clutch ) W1,3
Prod.No. 7429
Lever shaft for the clutch of the Wartburg 1.3 engine.
Mounting place: gearbox clutch void.
Spare part is complete with lever for the clutch cable and two arms for the clutch disenger.
99,50
steel contruction
made in Europe
Seite 87 from178
Wartburg 1.3 > Spare parts > Engine > ignition system
Wartburg 1.3 > Spare parts > Engine > Cylinder head
Wartburg 1.3 > Spare parts > Fuel sytem
Float needle valve W1,3 / T1,1 / B1000-1
Prod.No.
82
9,50
Oil seal gearbox casing - universal shaft left
Prod.No.
3153
6,44
Oil seal gearbox casing - universal shaft right
Prod.No.
3152
6,44
Prod.No.
Protection collar for the gear shifting shaft of the Wartburg 1.3 (4-stroke)
6933
12,50
6774
30,71
Valve for controlling the petrol level for the carburettor type:
32F 1-1 Trabant 1.1
34 TLA 51/2 Wartburg 1,3
34F 1-3 Barkas 1000-1
original spare part number: 135 29 40 230 078216
Wartburg 1.3 > Spare parts > gear box
Radial sealing for the Wartburg 1,3 gearbox.
Differential gear - universal shaft, right hand.
seal with readvancing twist
installation: right hand
made in Germany
Sleeve for gear shifting shaft
original spare part
Wartburg 1.3 > Spare parts > Front axle
Silent buffer bush for upper wishbone W1,3
Prod.No.
One set silentbuffer bush fit to the upper chassis arms of Wartburg 1,3.
delivery: two pieces
for each wishbone one set will be needed
Seite 88 from178
Spring W1,3 front axle
Prod.No. 7324
55,00
Coil spring for the Wartburg 1.3 front axle. Fit to both typs: Limousine and Tourist from vintage: 1988.
length of the spring: original (lo=414mm)
made in Germany
Telescopic shock absorber, W1,3 - front axle
Prod.No. 6063
38,40
Buffer for the Wartburg 1,3 front axle with coil spring. Fit to both typs: Limousine and Tourist from
vintage: 1988 onwards.
scope of delivery inclusive bushing down
upper side complete with mounting elements: 1x ring buffer A, 1x ring buffer B, 1x holder disc, 1x
hexagonal nut M8 and 1x spring washer
made in Germany
wheel bolt 40mm
Prod.No.
7200
3,30
Prod.No.
6450
3,30
universel wheel bolt fit to Wartburg, Trabant and DDR trailers and campers
Please note:
The length of 40mm consist the length of thread and the length of knurling.
legth: 40mm
thread: M12 x 1,5
thread length: 28mm
knurling diameter: 14,5mm
knurling length: 7,6mm
wheel bolt 50mm
Please note:
legth: 50mm
thread: M12 x 1,5
thread length: 38mm
wheel bolt 50mm with flat portion
Prod.No. 7677
3,50
Wheel bolt fit to the Wartburg 353 and 1.3 front axle with disc brake system. Inclusice one side cuted.
Please note:
legth: 50mm
thread: M12 x 1,5
thread length: 37mm
wheel bolt 60mm
Prod.No.
7201
3,10
Please note:
legth: 60mm
thread: M12 x 1,5
thread length: 48mm
Seite 89 from178
wheel bolt 60mm with flat portion
Prod.No. 7202
3,50
Wheel bolt fit to the Wartburg 353 and 1.3 front axle with disc brake system. Inclusice one side cuted.
Please note:
legth: 60mm
thread: M12 x 1,5
thread length: 48mm
wheel bolt 80mm
Prod.No.
7203
3,90
Prod.No.
Wheel hub for the Wartburg 1.3 front axle.
Please note: this spare part is not identical with the wheel carrier of the Wartburg 353!
The internal teeth of the drive shafts is different.
7397
65,00
Prod.No.
Mounting bolt for the rear axle of the Wartburg 353 and Wartburg 1.3 at the car frame.
Delivery a an single part.
7563
14,50
clamp for anti-roll bar
3225
9,50
Prod.No. 6612
rubber bearing fit for the clamp to mount the anti-roll bar of rear axle on underside of car
5,86
Please note:
legth: 80mm
thread: M12 x 1,5
thread length: 68mm
Wheel carrier W1,3
material: steel, surface blank
internal teeth: 21 teeth
bolt circle: 4x160mm
new production: made in Europe
one piece will be needed for each wheel side (front axle)
fir to the vehicles: Wartburg 1,3 Limousine, Tourist and Trans
Wartburg 1.3 > Spare parts > rear axle
Bolt for wishbone, rear axle
Prod.No.
Clamp to mount the anti-roll bar of rear axle on underside of car
wide of steel strip: 30 mm
thickness of steel strip: 2,5 mm
inner diameter of clamp: ca. 33 mm
drill diameter: 10,5 mm
inner rubber bearing for anti-roll bar
inner diameter: ca. 13 mm
wide total: ca. 39 mm
outer diamter (in the area of clamp: ca. 32 mm
Seite 90 from178
outer rubber bearing for anti-roll bar
Prod.No.
7014
5,56
Prod.No.
7015
4,36
Prod.No.
7666
52,86
outer rubber bearing fit for the the anti-roll bar of rear axle
inner diameter (smallest position): ca. 9 mm
wide total: ca. 29 mm
outer diamter (in the area of clamp: ca. 29 mm
outer rubber filler for anti-roll bar (1 pair)
One pair of rings, made of black rubber
fit to mount the retainer of anti-roll bar on left arm of rear axle
4 pieces will be needed for each raer axle
wide total: 15 mm
outer diamter: ca. 29 mm
Spring for rear axle W1,3 (Limousine)
Coil spring for the rear axle of car body variante: limousine
Fit to Wartburg 1,3.
size: midle diameter of the coil: 111 mm, total lenght of the unencumbered spring: 360 mm, wire
diameter: 14mm, count of coils: 8,5
made in Germany
Telescopic shock absorber, W1,3 - rear axle
Prod.No. 6064
37,40
Buffer for the Wartburg 1,3 rear axle with coil spring. Fit to both typs: Limousine and Tourist from
vintage: 1988 onwards.
made in Germany
wishbone, rear axle, left hand W353/W1.3
Prod.No.
6467
223,60
Prod.No.
6466
223,60
Prod.No.
6397
33,80
for both typs Limousine and Tourist
second-hand wishbone for left side of rear axle
wishbone, rear axle, right hand W353/W1.3
for both typs Limousine and Tourist
second-hand wishbone for right side of rear axle
Wartburg 1.3 > Spare parts > car body
Wartburg 1.3 > Spare parts > car body > rubber sections
outer rubber profile for door window
Complete for all doors.
Fit to Wartburg 353 and 1,3.
length: 2,50m
Seite 91 from178
Prod.No.
6113
98,25
Prod.No.
6114
98,25
Prod.No. 6785
Rubber profile fit to rear side window of car body variant *tourist* (estate car/ station wagon)
Fit to Wartburg 353 and 1,3.
length: 2,50m
two pieces will be needed for one Wartburg body
22,75
Profile for external door-duct weather strip. Complete for all doors.
Profile for external door-duct weather strip. Complete for all doors.
Rubber profile for rear side window *tourist* (W353/W1.3)
Rubber-section for rear window (tailgate), Tourist (W1.3)
Prod.No. 6822
41,11
Rubbersection for the rear window inside tailgate. Only for car body variant called Tourist (estate car/
station wagon) of Wartburg 1,3 (4-stroke).
rubber-section profile type for profile filler or profile filler chrome effect.
lenght: 4 meter
made in Germany
Window guiding profile -set Wartburg
Prod.No. 7626
83,25
Guiding rubber profile for the front and rear door windows of the Wartburg 353 and Wartburg 1.3
This rubber is an good replacement for the original profile, inclusive flocked guiding sides for the
screens.
Delivery at one piece.
length: 9m
made in Germany, colour black.
Wartburg 1.3 > Spare parts > Accessories
Speedometer with trip meter
Prod.No. 7092
24,99
Round speedometer for the cars Wartburg 1.3, Wartburg 353, Trabant 1.1, Barkas B1000 and B100-1.
type:
Speedscale up to 150km/h
inclusive trip meter
power 12V
scope of delivery inclusive bulbs
front rim : black
mounting diameter: 100mm
genuine spare part
Zak No: 3.0230/47
Trademark * 1,3 *
Prod.No. 3553
2,56
Plastic lettering for the rear of the Wartburg 1,3. Fit at the original holes. Mounting only with pins for
letterings.
High-grade new production.
material: plastic, black
made in EU
scope of delivery inclusive pins
Wartburg 1.3 > Spare parts > Accessories > valve caps
Seite 92 from178
Wartburg 1.3 > Tuning parts
Hub for Wartburg steering wheel
Prod.No.
7617
69,94
Steering wheel safety adapter kit.
Can be used for Wartburg 353 and Wartburg 1,3.
length total: 95 mm
pitch circle diameter of mounting screws: 74 mm
content:
hub for sport steering wheels made by RAID
mounting screws (countersunk head with hexagon socket)
Wartburg 1.3 > Tuning parts > harness belts
Wartburg 1.3 > Tuning parts > Roll bar
Wartburg 1.3 > Tuning parts > Suspension
Prod.No. 6780
47,07
Wartburg 1,3 front axle.
made in Germany
Prod.No. 6781
55,50
made in Germany
Prod.No. 6840
59,00
made in Germany
Prod.No. 6783
46,07
Wartburg 1,3 rear axle.
made in Germany
Seite 93 from178
Prod.No. 6782
48,20
made in Germany
Prod.No. 7089
54,00
made in Germany
Wartburg 1.3 > Tuning parts > valve caps
Barkas B 1000
Barkas B 1000 > Spare parts
Barkas B 1000 > Spare parts > Exhaust system
After muffler ( two stroke )
Prod.No.
4002
49,03
Prod.No.
4003
24,30
Prod.No.
4004
1,34
Silencer for Barkas B1000 two stroke engine.
mounting: between connection pipe and muffler with pipe.
material: sheet metal, basic colour
made in EU
After muffler with pipe ( two stroke )
Silencer with pipe for Barkas B1000 two stroke.
mounting: in the end of the exhaus system, next to the aftermuffler.
made in EU
Clamp D=45mm
universal-clamp for exhaust pipe D=45mm
Barkas B1000 two stroke 1 piece needed
(connection Exhaust aftermuffler - Muffler with pipe)
Seite 94 from178
Connection pipe ( two stroke )
Prod.No.
4001
24,81
Prod.No.
4007
14,88
Prod.No.
6359
2,26
Exhaust tube for Barkas B1000 two stroke.
mounting: between main silencer and aftermuffler
material: metal pipe, basic colour
made in EU
Holding device for pre-silencer
Holding device for pre-silencer
for Barkas B1000 2 stroke engine
Pipe clamp D=45mm
universal-clamp for exhaust pipe D=45mm
made of 2mm steel strip
zinc-coated
width: 25mm
Barkas B1000 two stroke 1 piece needed
(connection Exhaust aftermuffler - Muffler with pipe)
Pre-silencer ( two stroke )
Prod.No. 4000
Main silencer for Barkas B1000 two stroke.
mounting: in the beginning of the exhaus system, between exhaust manifold and connection pipe.
85,66
made in EU
Prod.No.
4006
3,95
Prod.No.
6081
2,46
for Barkas B1000 3 pieces will be needed
Barkas B 1000 > Spare parts > Brakes
Bleeder screw, rear
Bleeder screw for rear wheel brake cylinder B1000 and Multicar M22 - M25
Brake drum ( single part )
Prod.No. 4200
76,00
Drum for the wheel brake system of the vehicles B1000 and Barkas B1000-1 without latest serial of
the 4-Takt Barkas with disc brake.
Fit to both types of brake master cylinders single- and two circle.
The brake drum can be mounted at the front and the rear axle.
bolt circle 5x140mm
made in EU
Seite 95 from178
Brake hose, rear
Prod.No.
4222
7,96
Prod.No.
4212
56,88
Prod.No.
7525
49,50
Prod.No.
4202
12,88
Prod.No.
6175
7,73
Prod.No.
6282
0,25
Prod.No.
6176
3,61
Prod.No.
6454
3,18
Brake hose, rear for Barkas
length total: 18,5 cm
Brake pressure regulatoring valve, complete
Brake pressure regulatoring valve for Barkas B1000
without protection bellows
without mecanical components
Brake shoe set rear axle
Brake shoe kit for the Barkas B1000 and B1000-1 rear axle.
for each car one kit will be needed
Contens: four pieces of brake shoes without mounting parts
best quality of EU production
Brake shoe, complete ( rear ), single part
Brake shoe rear axle Barkas.
two pices for each wheel side
distributor
2 pieces for each B1000 needed
material: brass
thread : M12 X 1
Hexagon bolt for wheel brake cylinder
Hexagon bolt M6 x 14 mm 10.9 for wheel brake cylinder front and rear axle
complete with spring washer.
front axle each wheel side 4 pieces
rear axle each wheel side 1 piece
pipe-connector
4 pieces for each B1000 needed
galvanized
thread : M12 X 1
release spring for brake shoes, long
long version of release spring for break shoes
fit to follow brake systems:
brake drum front axle Wartburg 353 (two pieces for each wheel side)
brake drum rear axle W353 (one piece for each wheel side)
brake drum front axle B1000 (two pieces for each wheel side)
brake drum rear axle B1000 (one piece for each wheel side)
trailer with brake shoe wide of 50mm (e.g. Bastei, Intercamp, Camptourist CT9): one piece for each
wheel side
Seite 96 from178
release spring for brake shoes, short
Prod.No.
6455
2,94
short version of release spring for break shoes
brake drum rear axle Wartburg 353 (one piece for each wheel side)
brake drum rear axle B1000 (one piece for each wheel side)
trailer with brake shoe wide of 50mm (e.g. Bastei, Intercamp, Camptourist CT9): one piece for each
wheel side
retainer for brake hose
Prod.No.
6534
4,73
Ring sleeve, for wheel brake cylinder, complete rear ( incl. 2 pieces ) Prod.No.
4209
6,83
Brake hose retainer for Barkas
fit or all types of B1000
for one vehicle you need 10 pieces
slot wide: 14 mm
thickness: 1,75 mm
Ring sleeve, for rear wheel brake cylinder.
Fit to all models of Barkas and Wartburg 353 with brake drum system at the front axle.
Ring sleeve, rear axle, original
Prod.No. 7232
14,73
Original ring sleeve set for rear wheel brake cylinder.
Fit to all models of: Multicar M22, Barkas, Wartburg 311, 312, 313 and Wartburg 353 with brake drum
system at the front axle.
Comlete set for one wheel brake cylinder: 2x cap sleeve, 2x dust cap
temporary only the inner parts made in Germany in high quality, outer parts made in Hungary
material: break fluid resistant rubber
Screw-cap for brakeline 6 x 0,7
Prod.No.
7276
1,00
Prod.No.
4204
9,87
Prod.No.
6285
0,19
Prod.No.
4213
38,50
Screw-cap for brakeline 6mm x 0,7mm
Barkas B-1000
thread: M12x1
Sliding piece for rear brake shoe
Sliding piece for rear brake shoe Barkas
two pieces for each wheel side
Split pin 3,2 x 16
Split pin can be used for brake-shoes rear axle.
Two pieces for each wheel side.
spring kit for brake pressure regulatoring valve
Mechanical part of LAD 75 for Barkas B1000
with cap, seal, washer, 2 compression springs, pressure rod and spring plate.
Seite 97 from178
Universal brake line 6x0,7 *5m*
Prod.No. 6039
16,21
Zinced and PVC-plated steel brake line.
Scope of delivery 5 meters.
The pipe can be bent by hand with normal pressure. For the flange on the end of the tubes it will be necessary to use an
professional tube border tool.
thickness: 0,7mm
length: 5m
made in Germany
Universal brake line, CUNIFER 5m, 6mm
Prod.No.
7398
42,99
Prod.No.
6038
3,55
Brakepipeline 6 x 0,7 mm
made of NiCuFe
length: 5m
for B1000, B1000-1, Mulicar M22, M24, M26, Framo, Warburg 311 and 313
Universal brake line, PVC-coated per 1 m , 6 x 0,7 mm
Brakepipeline 6mm x 0,7mm for Barkas B1000
price per meter.
max. lenght per piece: 5m
Wheel brake cylinder rear, original
Prod.No. 7233
35,39
Complete in Germany overhauled rear wheel brake cylinder with cap sleeves, brak-piston
D=25,35mm.
Mark: IFA BHL
Fit to Wartburg 311 und Barkas B1000, B1000-1
scope of delivery: inclusive cap sleeves and bleeder screw
also used for some IFA-vehicles
mark Renak IFA BHL to our company in advance!
Wheel brake cylinder, rear
Prod.No.
4207
29,64
Prod.No.
7259
2,49
Wheel brake cylinder for the raer axle Barkas and Wartburg 311
made in Europe
Barkas B 1000 > Spare parts > Brakes > front brake
Adjusting nut for brake cable, long
Spezial nut with snap postions for adjusting the play of the brake cables.
It fit to front wheel hand brake system of the BARKAS B1000 and B1000-1
fit to the old and the later brake system
for the new hand brake system 3 pieces will be needed
for the old hand brake system 2 pieces will be needed
Seite 98 from178
Bleeder screw, M12x1
Prod.No.
Bleeder screw for many IFA vehicles. Tap M12 x 1 with selaing cone 90 degrees.
Fit to:
6121
3,74
Prod.No.
4231
22,57
Prod.No.
6657
20,50
6658
20,50
Prod.No. 4232
fit for right front wheel
for latest version of hand brake system with hand brake lever mounted next to the driver seat.
22,57
Barkas B1000
Barkas B1000-1
Multicar M22
Multicar M24
Multicar M25
Wartburg 311 and 313
Brake cable, long, left hand, complete (new version)
fit for left front wheel
for latest version of hand brake system with hand brake lever mounted next to the driver seat.
length of bowden sheathing: 116 cm
Brake cable, long, left hand, complete (old version)
fit for left front wheel of BARKAS
only fit to old version of hand brake system with hand brake lever mounted in dashboard
length of bowden sheathing: 79,5 cm
Brake cable, long, left hand, complete (old version)
Prod.No.
fit for left front wheel
for old version of hand brake system with hand brake lever mounted in dashboard
ength total: 110 cm
length of bowden sheathing: 79,5 cm
Brake cable, long, right hand, complete (new version)
length of bowden sheathing: 116 cm
Brake cable, short, complete
Prod.No.
Connection brake cable between the hand brake lever and the beam (in balance).
Can be used for models with hand brake lever between the front seats.
total length: 880mm
lenght of the bowden cable: 520mm
4230
12,60
Brake cable, short, complete (old version)
6660
28,50
4220
8,48
Prod.No.
connection cable for hand brake lever of BARKAS
only fit to old version of hand brake system with hand brake lever mounted in dashboard
Brake hose, front outside
Prod.No.
Flexible brake hose for the Barkas B1000 and B1000-1 drum brake frot axle.
total length: 49 cm
tap: 1x M12 x 1,5 core thread and 1x M12 x 1,5 male thread
Seite 99 from178
Brake shoe, complete, with lining ( front )
Prod.No.
4201
connection brake line
Prod.No. 6456
brake line to connect both wheel brake cylinders inside of brake drum of front axle Barkas B1000
usable for each side (rigth/left)
12,88
5,56
Eccentric bolt for front brake shoe
Prod.No.
4203
8,95
Prod.No.
4221
8,77
Prod.No.
6472
9,96
Eccentric bolt for front brake shoe Barkas
Inner brake hose, front
length total: 28,5 cm
left thrust rod for brake shoes
thrust rod fit to the left side of rear wheel brake
left brake drum rear axle Wartburg 353 with brake shoe wide of 50mm (one piece)
left brake drum front axle B1000 (one piece)
left brake drum rear axle Multicar M22 (one piece)
Mounting kit eccentric bolt for front brake shoe
Prod.No. 7524
1,00
This set can be used to fix the eccentric bolt at the front brake shoe of the Barkas B1000 and
B1000-1.
Scope of delivery:
1x grooved pin
1x mounting nut
1x spring washer
1x washer
1x snap ring
one kit for each wheel side
rigth thrust rod for brake shoes
Prod.No.
6471
19,96
4208
4,69
thrust rod fit to the right side of rear wheel brake
rigth brake drum rear axle Wartburg 353 with brake shoe wide of 50mm (one piece)
right brake drum front axle B1000 (one piece)
rigth brake drum rear axle Multicar M22 (one piece)
Ring sleeve, for wheel brake cylinder, complete front ( incl. 2 pieces )Prod.No.
made in Europe
Seite 100 from178
Ring sleeve, for wheel brake cylinder, front, original
Prod.No. 7325
Sleeve for front wheel brake cylinder of the Barkas B1000 and B1000-1 and Multicar M24.
Best quality made in Germany.
The set included 2 pieces.
The ring sleeve should only be changed, if inner surface of cylinder is okay.
Otherwise the complete wheel brake cylinder should be changed.
Wheel brake cylinder, front left hand
Prod.No.
Brake cylinder for the front axle oft the Barkas B1000, B1000-1 and Multicar M24.
mounting place: front left hand
For each car two pieces will be needed
Made in EU.
9,50
4205
29,50
Prod.No. 7172
Complete in Germany overhauled front wheel brake cylinder with ring sleeves and brak-piston.
Mark: RENAK LZ 5
28,50
Wheel brake cylinder, front left hand, original
scope of delivery inclusive sleeves
without adjuster
piston diameter: 31,8 mm
fit toBarkas B1000, B1000-1 and Multicar M24
mark Renak RENAK LZ 5 to our company in advance!
Wheel brake cylinder, front right hand
Prod.No.
Brake cylinder for the front axle oft the Barkas B1000, B1000-1 and Multicar M24.
mounting place: front right hand
For each car two pieces will be needed
Made in EU.
4206
29,50
Prod.No. 7173
Complete in Germany overhauled front wheel brake cylinder with ring sleeves and brak-piston.
Mark: RENAK LZ 5
28,50
Wheel brake cylinder, front right hand, original
scope of delivery inclusive sleeves
without adjuster
piston diameter: 31,8 mm
fit for Barkas B1000, B1000-1 and Multicar M24
mark Renak RENAK LZ 5 to our company in advance!
Barkas B 1000 > Spare parts > Brakes > master brake cylinder
Prod.No.
6346
128,17
Brake master cylinder, 1 circle for Barkas B1000 (old type)
Seite 101 from178
Prod.No. 7221
128,17
Type: Renak CH
Shipping only after your old brake cylinder with the mark IFA BH1 was send to our company.
Brake master cylinder, 1 circle for Barkas B1000, Mulicar M22, Mulicar M24, ZT, 3to-Stapler, Warburg
311,312,313, Framo.
Prod.No.
4210
98,50
Prod.No.
6741
111,22
Brake master cylinder, 2 circle for Barkas B1000, B1000-1
complete.
Made in EU
Brake master cylinder, 2 circle for Barkas B1000
complete with premounted 2-times distributor and brake light switch
Holder for brake fluid reservoir
Prod.No. 7151
Retaining strap for brake fluid tank, fit to 1-circle brake master cylinder or hydraulic cluch system.
5,50
material: steel
surface: galvanized
Pipe master brake cylinder - plastic reservoir (570mm)
Prod.No.
6292
3,83
Prod.No.
6291
4,32
Prod.No. 4214
Protection bellows for the single and tandem brake master cylinders.
fit ot vehicles: Framo, B1000, B1000-1, Wartburg 311, 312, 313, 353, Multicar M22, M24, M25.
6,89
connection hose from brake fluid reservoir to 2-circle master brake cylinder
length: 570 mm
one piece needed
Pipe master brake cylinder - plastic reservoir (670mm)
connection hose from brake fluid reservoir to 1-circle or 2-circle master brake cylinder
length: 670 mm
one piece needed
inner diameter conical end: 15 mm
inner diameter cylindrical end: 37 mm
length: 35 mm - 58 mm
Sleeve set dual brake master cylinder, complete
Prod.No.
4211
12,40
Prod.No.
7188
19,50
Sleeve set dual brake master cylinder, Barkas B1000
complete set
Also suitable for 2-circle brake master cylinder of Multicar M25.
Sleeve set dual brake master cylinder, original, Barkas
Sleeve set dual brake master cylinder, MBarkas B1000, B1000-1
complete set
made in Germany
Barkas B 1000 > Spare parts > Electrical system
Seite 102 from178
Ignition look
Prod.No. 7258
95,00
original and brand new ignition switch and look with keys for the Barkas B1000 and B1000-1 with
steering look.
original spare part
Main switch for car batterie
Prod.No.
6568
23,11
Prod.No.
1122
26,16
Prod.No.
4100
19,78
main switch for car batterie of Barkas B1000
with removable triggering key made from red plastic
two bolts M10 for wire connection
diameter of mounting holes: 6,4 mm
distance between mounting holes (centre-centre): 45mm
for save disconectedness of car batterie from mains (positive or negatve pole)
transferable power (switching capacity):
6V: 600W (100A)
12V: 1000W (ca. 80A)
24V: 1000W (ca. 40A)
Barkas B 1000 > Spare parts > Electrical system > Lighting
Headlamp H4 Barkas
headlamp insert for Barkas B1000 and B1000-1
type for 12V H4 bulbs
scope of delivery without bulbs
made in EU
Indicator lamp complete, front
Lamp for number plate right/left
Prod.No. 7346
9,87
New lamp for number plate lighting from right or left side of number plate
Fit to all closed body variants of Barkas B1000 (bus, transporter, ambulance) and many campers and
trailers
scope of delivery without bulbs (10W Ba15s)
hole distance for mounting: 72 mm (not 75 mm9
two pieces will be needed for each vehicle
Lamp for number plate semicircular right/left
Prod.No. 7364
9,87
Beautyful lamp for number plate lighting from right or left side of number plate
Fit to all closed body variants of Barkas B1000 (bus, transporter, ambulance) and many
campers and trailers
scope of delivery without bulbs 5W
hole distance for mounting: 72 mm (not 75 mm
two pieces will be needed for each vehicle
Seite 103 from178
Rearlight
Prod.No.
6621
35,20
Prod.No.
7584
8,50
Prod.No. 7439
Rubber plate for the rear light of the Barkas B1000, B1000-1 and Wartburg 311,312,313.
13,60
rear light complete for Barkas B1000 and B1000-1
original spare part
Sealing for HeadlampBarkas
Rubber ring for the headlamp Barkas B1000 and B1000-1
Sealing plate Rearlight
original spare part
Barkas B 1000 > Spare parts > Engine
Fan-shaft complete
Prod.No. 4426
133,43
Complete fanshaft consist of:
short and long fan shaft, flexible transmitter disc, sheet-metal profile with ball bearing and plastic fan.
complete set, pre-installed
Fan-shaft, long
Prod.No.
4427
48,39
Prod.No.
6304
0,88
long fan-shaft with two textile reinforced rubber discs
new produced (not original)
one piece neeeded
Fitted key 3 x 3,7
Fitted key (3 x 3,7) for fan-shaft and shaft of water pump
B1000: three pieces needed for complete fan-shaft
B1000 / W353: two pieces needed for shaft of waterpump
Seite 104 from178
grooved ball bearing for Fan-shaft and water pump shaft
Prod.No.
6298
9,44
grooved ball bearing for shaft of water pump and fan shaft
for Wartburg 353 and B1000 (2-stroke)
high quality made by FAG
size: 12 x 37 x 12
for the water pump shaft of the Wartburg 353 and Barkas B1000: two pieces are needed
for the Fan shaft Barkas one piece will be needed
Magnet, complete for starter 12V
Prod.No.
6067
39,79
Ring gear for starter
Prod.No.
4444
25,96
Prod.No.
rubber spring for motor- and gearbox- holder Barkas 2-stroke and Wartburg 353
one side with bolt and the other side with nut
4441
7,72
4440
4,88
ring gear for starter fit to all Barkas B1000 2-stroke engine
It fir to both clutch systems D=180mm and D=200mm.
Rubber spring for engine and gear box
for Barkas one piece will be needed
for Wartburg two pieces will be needed
Rubber spring for radiator
Prod.No.
spring suspension for cooling water radiatior
fastening the radiator at the carbody
material: rubber with thread bolt on both ends
Sealing for water pump
Prod.No. 6770
34,50
Speacial seling system for the water pump inside the cylinder head of the Warturg 353 and Barkas
B1000.
made in Europe
inclusive rubber seal
for Wartburg 353 up to 5-85 will be two pieces needed
for Wartburg 353 from to 5-85 and Barkas B1000 will be one piece needed
Snap ring for grooved ball bearing
Prod.No. 6537
Circlip for grooved ball bearing 6301 for shaft of water pump Wartburg 353 and B1000 (2-stroke)
0,98
textile-rubber disc for fan-shaft
7,95
Prod.No. 6239
with textile reinforced rubber disc,
holes with sheet-metal eyelets
to connect the both fan-shafts and the fan-shaft long in tandem with the shaft of water pump
two pieces needed for one B1000
Seite 105 from178
V-belt 9,5 x 1175 (B1000)
Prod.No.
6680
14,40
Prod.No.
4430
225,00
Prod.No.
4432
125,00
Prod.No.
6594
165,50
standard V-belt fit to Barkas B1000
10 x 1175
Barkas B 1000 > Spare parts > Engine > clutch
Cluch ( 4 stroke )
(+ 100,00 Euro deposit)
Cluch for Barkas B1000 4-stroke engine
fit to cluch disk 4-stroke engine
pledge for old clutch +100,00 Euro!
if old part will be sended back the money will be transfered back
for more informations, see details or below}
Cluch disk B1000-1 ( +50 ? deposit )
cluch disk for Barkas B1000-1 with 4-stroke engine
, Cluch][one piece will be needed]}
deposit for old clutch disk +50,00 Euro!
For more informations, see details or below.
Clutch for B1000 up to 02/1985
+80,00? deposit
Clutch for Barkas B1000 models up to year February 1985.
fit to clutch disc diameter 180mm, our order no. 3100)
with additional thrust bearing for old version of release bearing
Clutch cable complete
Prod.No. 4434
15,81
Clutch cable for the Barkas B1000. Fit to all two stroke models with mechanical cable clutch system.
total length 940 mm
genuine spare part
Clutch cylinder gearbox side
Prod.No. 7167
57,40
Overhauled clutch cylinder for the Barkas B1000. Fit to all two stroke models with hydraulic clutch
system.
company in advance!
genuine spare part
Clutch cylinder pedal side
Prod.No. 7166
55,00
Overhauled clutch cylinder for the Barkas B1000. Fit to all two stroke models with hydraulic clutch
system. Also fit to Multicar M22.
company in advance!
genuine spare part
Seite 106 from178
Clutch disk D=200mm (two stroke) Made in EU
Prod.No.
6595
85,80
Prod.No.
4433
85,80
clutch disk for Barkas B1000 2-stroke engine
diameter 200 mmm
for vehicles with vintage from 03/1985 onwards
fit to Slip ring disengager, Cluch
Clutch disk D=200mm (two stroke) Made in Germany
clutch disk for Barkas B1000 2-stroke engine
diameter 200 mmm
for vehicles with vintage from 03/1985 onwards
Made in Germany
fit to Slip ring disengager, CluchPlease note:We can only exchange you this spare part, if you ship 1x
clutch disc B1000 D=200mm to our company in advance!
Clutch from 03/1985, D=200mm ( two stroke )
Prod.No.
4431
165,50
Clutch for Barkas B1000 two stroke engine from year 3/1985,
fit to clutch disk D= 200 mm
Made in Germany
Please note:We can only exchange you this spare part, if you ship 1x clutch B1000 D=200mm to our
company in advance!
Clutch set ( 4 stroke ) (+150,00 ? deposit)
Prod.No.
6317
298,64
Prod.No.
6593
237,29
Complete clutch set
Clutch set fit to Barkas B1000-1 with 4-stroke engine.
Diameter of this clutch is also 200mm, but it is NOT the same like the 2-stroke type.
contens:
clutch (Art.No.: 4430)
clutch disc (Art.No.: 4432
release bearing (Art.No.: 680)
deposit for old clutch and cluch disk +150,00 Euro!
for more informations, see details or below
Clutch set D=200mm ( two stroke )
(+90,00Euro pledge)
Complete clutch set with diameter of clutch disc of 200 mm.
It fit to Barkas B1000 2-stroke engine (vintage of vehicle: from 03/1985 onwards).
contens:
clutch disc (Art.No.: 4433)
release bearing Art.No.: 3104
pledge +90,00 Euro!
if old part will be sended back the money will be transfered back
for more informations, see details
Seite 107 from178
Clutch set B1000, D=200mm ( two stroke )
Prod.No.
Complete clutch set with diameter of clutch disc of 200 mm.
It fit to Barkas B1000 2-stroke engine (vintage of vehicle: from 03/1985 onwards).
contens:
6316
280,36
clutch disc (Art.No.: 4433)
release bearing Art.No.: 680
Please note:We can only exchange you this spare part set, if you ship 1x clutch B1000 D=200mm and
one clutch disc B1000 D=200mm to our company in advance!
Fork for clutch disanger B1000-two stroke
Prod.No.
7266
34,67
Prod.No. 7673
Fit for for Barkas B1000 two stroke(vintage up to 02/1985) and Barkas B1000-1 four stroke.
39,67
Original fork for the pressure disanger for the Barkas B1000.
Scope of delivery with push pin and ball bearing.
Fit only to all two stroke models with hydraulic clutch system.
original no.0401157008
genuine spare part
Friction surface for clutch disc D200mm, original
size: 200x135x3,5mm
not pree drilled
made in germany
Friction surface for clutch disc D200mm, Valeo
Prod.No. 7674
Spare part for the clutch disc made by Valeo.
Fit for for Barkas B1000 two stroke(vintage up to 02/1985) and Barkas B1000-1 four stroke.
39,67
size: 200x137x3,2mm
complete pree drilled
made in germany
sleeve for cluch cable
Prod.No.
6474
9,80
sleeve for clutch cable
)
2-stroke and 4-stroke type of B1000 with clutch cable
NOT for hydraulic clutch triggering
length: 90mm
lenght (short): ca. 55mm
inner diameter big: 14mm
inner diameter small: ca. 8mm
made of soft rubber
Subject to availability (no regular range)!
Seite 108 from178
Sleeve for clutch cylinder gearbox side
Prod.No. 7181
4,50
Ring sleeve for the clutch cylinder release fork of the Barkas B1000. Fit to all two stroke models with hydraulic clutch
system.
made in Germany
genuine spare part
Sleeve set for clutch cylinder pedal side
Prod.No. 7169
8,50
Sleeves for the clutch cylinder of the Barkas B1000 and Multicar M22. Fit to all two stroke models of
Barkas with hydraulic clutch system.
Set consist of 1x ring sleeve and 1x cap sleeve.
made in Germany
genuine spare part
Tank for brake fluid with one gland
Prod.No.
6421
16,74
used for B1000 2-stroke:
1-circle brake master cylinder in tandem with mechanical clutch driving system
clutch driving cylinder in tandem with a 2-circle brake master cylinder
Barkas B 1000 > Spare parts > Engine > ignition
Ignition cable set B1000 high quality, 5 kOhm
Prod.No. 7358
24,59
Very good spare part for replacement the original one at all Barkas B1000 with two stroke enine.
Fit to all spark plugs M14 with connector thread M4
With a five kilo ohm resistor for suppression of interference it is a ideal replacement part for most (2-stroke) vehicles, which
were bulit in G.D.R.
suppression of interference (5 kOhm)
three silicon ignition wires cuted and complete manufactured with spark plug terminals, high quality made in Germany
Barkas B 1000 > Spare parts > Engine > Piston
Barkas B 1000 > Spare parts > Engine > carburettor & air intake
Carburettor Barkas B1000
Prod.No. 7032
145,00
Complete overhauled Carburettor for the three cylinder two stroke Wartburg engine with 1000 ccm
Carburettor type: 40F 1-12
Please note, we can only exchange you this spare part if you ship 1x carburettor 40 F2-12 to our
company in advance!
Choke bowden cable
Prod.No.
6866
14,50
Choke bowden wire for the Barkas B1000 two stroke.
total length: 1780mm
length wire hull: 1690mm
Barkas B 1000 > Spare parts > Engine > Cooling system
Seite 109 from178
Prod.No. 7282
29,86
Cooling wather hose for the connection between thermostat housing cylinder head and upper
connector cooling radiator. Used length: 53cm.
bup to 6 bar
up to 125°C
Prod.No. 7283
29,86
Cooling wather hose for the connection between lower connector cooling radiator and water pump
housing. Used length: 97,5cm.
bup to 6 bar
up to 125°C
Engine for heater
Prod.No.
4397
Seal for thermostat case top
67,58
Prod.No. 7596
Thermostatseal fit to the top colling water pipe connection at the Barkas B1000 two stroke engine.
3,25
thickness: 1mm
made in Germany
Barkas B 1000 > Spare parts > gearbox
Band clamp for sleeve rubber ( outer universal shaft side )
Prod.No.
6552
4,85
Clamp for rubber sleeve other universal shaft of Barkas B1000 and B100-1
length: 680 mm, width: 8 mm
made in Germany
for each outer sleeve rubber, one piece will be needed
Prod.No. 7392
2,49
Single part of the cylindrical roller for the freewheel of the Barkas B1000 (old and later type of
gearboxes and B1000-1.
length: 12mm
made in Germany
Seite 110 from178
Drive shaft overhauled
Prod.No.
4420
303,33
Prod.No.
4422
416,50
Prod.No.
4399
22,40
complete overhauled driven shaft for Barkas B1000.
Drive shaft, complete
new drive shaft with double hinge
fit for all Barks B1000 types (2-stroke and 4-stroke)
delivery without sleeve rubber
Flexible shaft for speedometer
fit for Barkas
Freewheel crate complete
Prod.No. 4410
59,90
The set included: 1 x Freewheel cam, 12 x Clinder roller and 1x Freewheel crate.
Fit for gearboxes type WA 10,5 S4 M (latest 2 stroke model with mecanical cluth) Barkas B1000 and
B1000-1.
O-seal 110 x 3 bearing bushing
Prod.No. 7612
1,75
Rubber sealing ring for the gearbox bearing bushing (main bearing differential gear).
Fit to all Barkas B1000 gearboxes old type with hydraulic clutch system and late gearboxes with wire
clutch system.
material: NBR 70
made in Germany
for each side of gearbox (differential gear) is one piece needed, total 2 pieces
One pair of sliding sleeve halves for drive shaft
Prod.No. 7026
21,55
One pair of sliding sleeve halves for mounting between sleeve rubber (wheel side) and drive shaft of
Barkas B1000
These sliding sleeve halves are made of thermosetting plastic, so they are more stable than the new
produced one made of rubber
For each shaft one pair will be needed.
Radial shaft seal 42 x 55 x 7 SL
Prod.No.
7204
6,10
Prod.No. 6391
Radial sealing for the gearbox connection side of the dirve shafts.
Fit to all Barkas B1000 and B1000-1 gearboxes late type with mechanical clutch system.
6,11
Fit to all Barkas B1000 gearboxes old type with hydraulic clutch system.
material: NBR
made in Germany
Radial shaft seal 52 x 68 x 8
material: NBR
made in Germany
Seite 111 from178
Radial shaft seal 52 x 68 x 8 SL
Prod.No.
7390
6,51
Prod.No.
4418
8,95
Prod.No.
4417
8,89
Prod.No.
Sleeve can be used for the models Barkas B1000 and B1000-1.
Fit to cars with douple hinge universal shaft and with single hinge driven shaft.
Can be mounted without disassembly the driven shafts.
4416
9,38
Sealing ring inclusve dust lip (WAS)
Fit to all Barkas B1000 and B1000-1 gearboxes late type with mechanical clutch system.
material: NBR
made in Germany
Sleeve rubber ( inner universal shaft side )
sleeve rubber for inner side of universal shaft of Barkas B1000
for each shaft is one sleeve rubber (gearbox side) needed
Sleeve rubber ( outer universal shaft side )
Sleeve rubber ( outer universal shaft side ), splited
delivery without equipment
made in EU
one piece will be needed for each wheel
Sliding sleeve halves (universal shaft)
Prod.No. 6365
Sliding sleeve halves for mounting sleeve rubber (wheel side) at universal shaft of Barkas B1000
6,07
for each shaft are two sliding sleeve halves needed
Barkas B 1000 > Spare parts > Fuel system
Transmitter for fuel gauge bus
Prod.No.
Sensor for fuel gauge with potentiometer for connection to all offert fuel gauges.
Fit to all Barkas B1000 and B1000-1 models of Bus
Scope of delivery complete with rubber sealing and float.
7467
39,90
made in Germany
Seite 112 from178
Transmitter for fuel gauge Pick up
Prod.No.
Sensor for fuel gauge with potentiometer for connection to all offert fuel gauges.
Fit to all Barkas B1000 and B1000-1 models of Pick up
Scope of delivery complete with rubber sealing and float.
7459
39,90
Prod.No.
7603
38,44
Prod.No.
6940
38,44
Ball joint for steering push rod, right hand ( cone 16 mm ) Germany Prod.No.
6941
38,44
Prod.No.
7604
38,44
Prod.No.
7699
34,78
made in Germany
Barkas B 1000 > Spare parts > Front axle
Ball joint for steering push rod, left hand ( cone 18 mm )
Joint with left tap connection for the push rod with cone 18mm.
This spare part is produced in Europe.
Cone: diameter from 16mm to 15mm, thread M12x1,5
thread push rod side: M20x1,5 LEFT, tap length: 50mm
for each rod will be one left and one right ball joint needed
made in EU
Ball joint for steering push rod, left hand ( cone 18 mm ) Germany
This spare part is produced in Germany in high quality.
Cone: diameter from 14,5mm to 16mm, thread M12x1,5
thread push rod side: M20x1,5 LEFT, tap length: 50mm
made in Germany
Cone: diameter from 14,5mm to 16mm, thread M12x1,5
thread push rod side: M20x1,5 RIGHT, tap length: 50mm
made in Germany
Ball joint for steering push rod, right hand ( cone 18 mm )
This spare part is produced in Europe.
Cone: diameter from 15mm to 18mm, thread M12x1,5
thread push rod side: M20x1,5 RIGHT, tap length: 50mm
made in EU
Ball joint for track rod, left hand ( cone 14 mm ) Germany
Ball joint with left turn thread for track rod and with 14mm-cone
Cone: diameter from 12,7mm to 14mm, thread at the cone M10x1,0
thread steering rod side: M16x1,5 LEFT turn, thread length: 55mm
Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
made in Germany
Seite 113 from178
Ball joint for track rod, left hand ( cone 16 mm ) EU
Prod.No.
6458
27,21
Ball joint with right turn thread for track rod, left hand with 16mm-cone
big thread: M18x1,5
small thread (on top of cone): M12
Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left
turned thraead!
Ball joint for track rod, left hand ( cone 16 mm ) Germany
Prod.No.
7698
39,02
Ball joint with left turn thread for track rod and with 16mm-cone
thread steering rod side: M18x1,5 LEFT turn, thread length: 63mm
turned thraead!
made in Germany
Ball joint for track rod, right hand ( cone 14 mm ) Germany
Prod.No.
7700
34,78
Ball joint with right turn thread for track rod and with 14mm-cone
thread steering rod side: M16x1,5 RIGHT turn, thread length: 55mm
Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
made in Germany
Ball joint for track rod, right hand ( cone 16 mm ) EU
Prod.No.
6457
27,21
Ball joint with right turn thread for track rod, right hand with 16mm-cone
big thread: M18x1,5
turned thraead!
Ball joint for track rod, right hand ( cone 16 mm ) Germany
Prod.No.
7697
39,02
Ball joint with right turn thread for track rod and with 16mm-cone
thread steering rod side: M18x1,5 RIGHT turn, thread length: 63mm
turned thraead!
made in Germany
Ball joint for track rod, right hand ( cone 18 mm )
Prod.No.
4510
27,21
Ball joint with right turn thread for track rod, right hand with 18mm-cone
big thread: M18x1,5
turned thraead!
Ball joint for trak rod, left hand ( cone 18 mm )
Prod.No.
4511
27,21
Ball joint with right turn thread for track rod, left hand with 18mm-cone
big thread: M18x1,5
turned thraead!
Seite 114 from178
Between rod for steering
Prod.No.
4512
94,99
Bolt for knuckle-long, complete with needle bearing
Prod.No.
4514
33,50
Prod.No.
4515
33,50
Bushing for bearing
Prod.No.
4518
19,50
Connection joint steering column
Prod.No.
4519
65,80
Connection shaft left hand
Prod.No.
4517
85,00
Connection shaft right hand
Prod.No.
4516
85,00
Countersunk-head screw for brake drum
Prod.No.
6281
0,45
Prod.No.
6283
6,55
Set with bolt for upper side, fit to all B-1000 (Barkas)
compelete set with needle bearing.
length of bolt: 101mm
diameter of bolt: 25mm
outer diameter of needle bearing: 37mm
length of needle bearing: 30mm
Bolt for knuckle-short, complete with needle bearing
Set with bolt for down side, fit to all B-1000 (Barkas)
compelete set with needle bearing.
length of bolt: 86mm
diameter of bolt: 25mm
outer diameter of needle bearing: 37mm
length of needle bearing: 30mm
M8 x 16 mm
with hexagon socket
galvanized
Two pieces for each wheel side, used for front and rear axle
Hexagon slotted and castle nut
Hexagon slotted and castle nut M27 x 1,5 mm,
can be used for the front and rear axle.
One piece for each wheel side.
Seite 115 from178
Mounting nut steering gear leaver
Prod.No.
7713
3,95
Prod.No.
4526
16,54
Prod.No.
6775
17,80
Nut for mounting the steering gear leaver at the shaft.
Can be used for Barkas B1000 and B1000-1
Radial sealing 90 x 110 x 10
Radial sealing for Barkas -wheel baraing case front axle,
one piece for each wheel side.
Radial sealing 90 x 110 x 10 with additional dust lip
Radial sealing for Barkas -wheel bearing case front axle,
90x110x10
with additional dust lip (protect the sealing lip against wearout through dust)
shock absorber
Prod.No. 6299
84,94
Telescopic buffer with mounting eyes on top and down for the Barkas B1000 and B1000-1 front axle.
Modell: Van, pick up, fire-engine-vans and ambulace
absorber type: A3-200-220/50
made in Germany
Sleeve for push rod ( steering )
Prod.No.
4521
7,50
Slotted nut
Prod.No.
6279
29,85
Prod.No.
6280
0,27
Prod.No.
4520
267,96
slotted nut AM60 x 1,5 mm for wheel hub, final drive
One piece for each wheel side (front)
Split pin 5 x 50
Split pin can be used for the front and rear axle Barkas B1000 and B1000-1.
proticion from the castlel nut drivenshaft front axle and wheel hub rear axle.
surface: electrogalvanized (silver)
Steering gear complete overhauled
Pfand für Lenkgetriebe ( Altteil ), wird bei Rückgabe erstattet + 40Euro
Seite 116 from178
Steering push rod ( cone 16 mm )
Prod.No. 6648
98,63
Complete componet of steering rod. Fit to Barkas B1000. Delivery inclusive two universal joints (1x left tap nad 1x right tap
with cone 16 mm).
lenght of the rod: 91 cm
diameter D= 22 mm
lenght from middle-middle ball joints: ca. 97 cm
scope of delivery incl. two clips to locking thr joints
Steering push rod ( cone 18 mm )
Prod.No. 4513
98,63
Complete componet of steering rod. Fit to Barkas B1000 and B1000-1. Delivery inclusive two universal
joints (1x left tap nad 1x right tap with cone 18 mm).
lenght of the rod: 91 cm
diameter D= 25 mm
lenght from middle-middle ball joints: ca. 97 cm
scope of delivery incl. two clips to locking thr joints
Wheel bearing front axle ( 30208 )
Prod.No.
4525
29,99
Prod.No.
7494
6,60
Wheel hub, final drive
Prod.No.
4522
120,61
Wheel nut AM 14 x 1,5
Prod.No.
4524
2,91
Wheel bearing Barkas B-1000 and B1000-1front axle.
made by FAG
For each axle you will need two.
Wheel bolt B1000
Wheel bolt fit to Barkas B1000 and B1000-1.
This bolt was also used at some forklifts and trailers made in DDR.
Please note:
length: 41mm
thread: M14 x 1,5
thread length: 29mm
knurling diameter: 16mm
knurling length: 7mm
Wheel nut for Barkas B1000
for each wheel 5 pieces will be needed
bolt circle 5 x 140 mm
tightening torque 120 Nm
Seite 117 from178
Wheel rubber cap
Prod.No.
4523
10,09
Prod.No.
Hexagon screw for mounting the brubber bearing retainer at the vehicle frame.
Can be used for Barkas B1000 und B1000-1
Mounting place at the front and rear axle.
For the front axle will be four pieces needed as well for the rear axle.
Strength class: 10.9
spanner gap: SW19
7610
2,14
Prod.No.
4542
11,86
Prod.No.
4540
12,45
Prod.No.
6837
4,54
Prod.No.
6289
71,00
Prod.No.
6288
84,94
central cover for the B1000 and B1000-1 wheel hub.
Barkas B 1000 > Spare parts > rear axle
Mounting bolt for bearing retainer
Radial sealing 85 x 105 x 10
Radial sealing for rearaxle Barkas. (seal for wheelbearing)
Rubber bearing
Rubber bearing for Barkas
front and rear axle
two pieces will be needed for rear axle
two pieces will be needed for front axle
Rubber for shock wishbone
Buffer for the wishbone end position for the front and rear axle
8 pieces will be needed for rear axle
8 pieces will be needed for front axle
shock absorber
shock absorber for Barkas rear axle.
Modell: Van
absorber type: B3-200-150/50
made in Germany
shock absorber pickup
Modell: pickup
absorber type: A3-200-220/50
made in Germany
Seite 118 from178
shock absorber station, box wagon
Prod.No.
7058
71,00
Prod.No.
6290
71,00
Prod.No.
6284
26,50
Prod.No.
6905
111,72
Prod.No.
6286
115,00
Prod.No.
6287
115,00
Prod.No.
6241
16,45
Prod.No.
4541
25,97
Modell: Station wagon and box wagon
made in Germany
shock absorber Van, fire-engine-vans and ambulace
shock absorber for Barkas rear axle
Modell: fire-engine-vans and ambulace
made in Germany
Slotted nut
slotted nut AM55 x 1,5 mm for wheel hub, rear axle
One piece for each wheel side (rear)
summer tyre 6.70-13 P34
New produced reinforced summer tyre fit to Barkas B1000.
For each tyre one hose for wheel will be needed.
name of tyre: 6.70-13 6PR
name of tyre tread: P34 (original tread design)
Torsion bar spring left hand
Torsion bar spring left hand for Barkas.
rear axle
Torsion bar spring right hand
Torsion bar spring right hand for Barkas.
rear axle
Tube for wheel
Tube fit to the Barkas B1000 und B1000-1 tyre 6.70 R13.
delivery without valve.
Wheel bearing rear axle ( 30207 )
Wheel bearing rear axle Barkas
made by FAG
Two pices for each wheel side.
Barkas B 1000 > Spare parts > Panes & rubber sections
Seite 119 from178
Rubber section engine cover
Prod.No.
6979
3,27
Prod.No.
7465
3,90
Prod.No.
7715
11,97
Prod.No.
7463
2,30
Prod.No.
7464
1,30
Prod.No.
7714
2,90
Prod.No.
6976
35,00
Prod.No.
6973
35,03
Prod.No.
6975
36,83
black cellular rubber for engine covver inside the driver´s cap
length: 0,6 m
Fit to each body variant of Barkas B1000
One piece will be needed for one vehicle.
Rubber section for engine bonet
black cellular rubber for engine cover inside the driver´s cap.
length: 88 cm
Rubber section for engine bonet B1000-1
length: 2,70 cm
Fit to each body variant of Barkas B1000-1
Rubber section for engine cover
length: 1,05 m
Rubber section for engine cover
length: 58 cm
Rubber section for engine cover B1000-1
length: 1,70 m
Fit to each body variant of Barkas B1000-1
Rubber section for rear pop out window
original rubber section for pop out window right and left hand
length: 0,98 m
Number of pieces for different car body variants of Barkas B1000:
box with sheet metal side door (KA): n.a.
box with pane in side door (KM): n.a.
bus (KB): two pieces
ambulance SMH (KK): two pieces
pallet (HP): n.a.
Rubber-section for back door pane
box with sheet metal side door (KA): one piece
box with pane in side door (KM): one piece
bus (KB): one piece
ambulance SMH (KK): one piece
pallet (HP): n.a.
Rubber-section for door pane of driver´s cab
fit to all B1000 variants
length: 2,20 m
It needs one for door on drivers side and one for door on co-driver side.
Seite 120 from178
Rubber-section for rear pane of driver's cab
Prod.No.
6974
35,03
Prod.No.
6971
11,78
Prod.No.
6972
3,10
Rubber-section for rear pane of all car body variants with separat driver´s cab
bus (KB): n.a.
ambulance SMH (KK): n.a.
pallet (HP): one piece
Rubber-section for rear side pane, long
This rubber section will be used for posterior side panes of Barkas B1000
Directly mounted in car body on both sides.
Number of pieces for different car body variants:
bus (KB): 2 pieces
ambulance SMH (KK): 2 pieces
pallet (HP): n.a.
length: 1,9 Meter
Rubber-section for rear side pane, long
This rubber section will be used for posterior side panes of Barkas B1000
Directly mounted in car body on both sides.
bus (KB): 2 pieces
pallet (HP): n.a.
length: 0,5 Meter
Rubber-section for side pane of middle side part
Prod.No. 6969
9,95
This rubber section will be used for side panes behind the two front doors of Barkas B1000 (all car
body variants)
length: 1,40 Meter
Rubber-section for side pane of middle side part
Prod.No.
This rubber section will be used for anterior side panes of Barkas B1000
Directly mounted in car body on right side and mounted in side door on left side.
6970
18,98
box with sheet metal side door (KA): 1 piece
box with pane in side door (KM): 2 pieces
bus (KB): 2 pieces
pallet (HP): n.a.
length: 2,9 Meter
Seite 121 from178
Rubber-section for window guiding ( double )
Prod.No. 4504
33,25
Double U-rubber profil with velvet. Mounted at the side windows for the drivers and codrivers doors of
the Barkas.
Fit to all models like B-1000 and B1000-1
priece per piece, precutted length
made in Germany
Rubber-section for windscreen
Windscreen ( MSG ), colourless
Prod.No.
4500
47,41
Prod.No.
4501
270,00
Prod.No.
4502
270,00
no delivery possible!
Windscreen ( MSG ), with sunshild green
no delivery possible!
Windscreen wiper set Barkas, complete
Prod.No. 6839
28,84
One kit of wipers and wiper arms for B1000 and B1000-1 (please note: four stroke models only use for
types with old wiper linkage without grooved conical stub.
Wiper set consist of:
two piece wiper arm
tow piece wiper blade with rubber
Windscreen wiper set Barkas-1, complete
Prod.No. 7712
28,84
One kit of wipers and wiper arms for B1000-1 (please note: four stroke models with the late type of wiper linkage with
grooved conical stub.
Wiper set consist of:
two piece wiper arm
tow piece wiper blade with rubber
Wiper linkage B1000
Prod.No.
4503
52,09
Prod.No.
7709
52,09
Prod.No.
7100
29,58
Complete unit fit to Barkas B1000 and B1000-1
Wiper linkage B1000-1
Complete unit fit to Barkas B1000-1.
Barkas B 1000 > Spare parts > Body
Bering for outer rear view mirror, high quality
Mirror in high quality, inclusive mounting clamp.
material: PVC, black, shock proof with rubber edge
care side: right / left hand mountable
delivery inclusive arched plate glass for the best rear view.
made in Germany
fit to Barkas B1000 and B1000-1 and Multicar M25
Seite 122 from178
Door sealing Barkas
Prod.No.
6790
22,50
Prod.No.
6590
16,50
Prod.No.
6627
15,65
sealing rubber for car doors Barkas B1000 und B1000-1
material: profiled black cellular rubber
length: 3,60 meter
two or four pieces will be needed for each car
gear lever collar
collar for gear lever of B1000 (2-stroke)
width total: ca 178 mm
made in EU
plate glass for rear-view mirror
plate glass for the outer rear-view mirrors of Barkas B1000 and Multicar M25
domed mirror glass
height: 240 mm (highest extent)
width: 156 mm (wides extent)
symmetrical outlines (no conical outlines
Please check the dimension of your mirror, because differnt types of mirrors were mounted in the past.
Protector for front bumper
Prod.No.
4303
21,50
Prod.No.
4304
21,50
Prod.No.
4302
57,98
Prod.No.
6736
1,95
Solid rubber for the front bumber of the Barkas B1000 and B1000-1.
The rubber profil is splitted behind the numberblade (distance between 5cm)
two piece will be needed for each car
Protector for rear bumper
Solid rubber for the rear bumber of the Barkas B1000 and B1000-1.
length 55 cm for each one
Rear mudguard, pick up
Sealing plug for front floor (B1000)
Sealing plug for front floor of car body of B1000
diameter of rubber pad: 20 mm
thickness of rubber pad: ca 5 mm
diameter of mounting rubber pin (without cone): ca 5,5 mm
biggest diamter of cone: ca 9 mm
for one B1000 will four pieces needed (for all body variants)
Barkas B 1000 > Spare parts > Accessories
Seite 123 from178
Bering for outer rear view mirror
Prod.No.
4550
18,21
Prod.No. 6851
Elaborate made and exactly cuted two piece carped for the Barkas from vintage 1962-1990.
73,67
Mirror in simple quality, inclusive mounting clamp.
material: PVC, black
care side: right / left hand mountable
delivery inclusive plate glass
made in EU
fit to Barkas B1000 and B1000-1 and Multicar M25
Fitted carpet front, B1000, Nobless black
material: typ NOBLESS high quality soft velours, with rubber bottom and fringe
made in Germany
Fitted carpet front, B1000-1, Nobless black
Prod.No.
Elaborate made and exactly cuted two piece carped for the Barkas B1000-1 with four stroke engine
7046
59,00
material: typ NOBLESS high quality soft velours, with rubber bottom and fringe
made in Germany
Fitted rubber carpet front, B1000
Prod.No. 7047
59,00
Elaborate made and exactly cuted two piece rubber-carped for the Barkas
from vintage 1962-1990.
material: waterproof rubber, colour black
made in Germany
Fitted rubber carpet front, B1000-1
Prod.No. 7048
59,00
Elaborate made and exactly cuted two piece rubber-carped for the Barkas B1000-1 (four stroke
engine)
material: waterproof rubber, colour black
made in Germany
Fuel tank for KA, KB
Prod.No.
4554
104,93
Holding device for outer rear view mirror, left hand
Prod.No.
4552
14,67
Holding device for outer rear view mirror, right hand
Prod.No.
4551
14,67
Seite 124 from178
Trademark * B 1000 *
Prod.No.
4561
3,99
Prod.No.
4560
3,99
Prod.No.
Typical plastic trade mark with IFA stamping for mounting at the Barkas front door.
Label has two casted on mounting pins.
4562
4,98
6874
4,95
Plastic trade mark with lettering B1000 for mounting at the Barkas front door.
Label has 3 casted on mounting pins.
material: plastic
colour: black
length: ca 17,5cm
highness: ca. 3,2cm
made in EU
Trademark * BARKAS *
Plastic trade mark with lettering BARKAS for mounting at the B1000 or B1000-1 front door.
Label has 3 casted on mounting pins.
material: plastic
colour: black
length: ca 21,5cm
highness: ca. 3,2cm
made in EU
Trademark * IFA *
material: plastic
colour: black
made in EU
Barkas B 1000 > Spare parts > Accessories > valve caps
Trailer
7-pin connector for trailer
Prod.No.
with screwed terminals and cord grip
housing made of black plastic (ABS)
7-pin connector for trailer (incl. wiring to your selected cable)
Prod.No. 6873
12,30
This article contains the 7-pin connector for trailer use and the wiring to one end of selectetd cable you
have to order separately (PVC-vehicle-cabel or rubber cabel).
wiring table included
adapter plug for trailer
Prod.No. 6756
To connect the trailer plug with seven contacts to socket of towing vehicle with 13 contacts
19,80
Mini-adapter
with integrated terminal assignment inside the cap (see details)
easy installation
Seite 125 from178
blind rivet for toggle retainer for shirr
Prod.No.
7370
0,15
Prod.No.
7329
2,50
Prod.No.
6872
7,42
Prod.No.
7330
8,87
Prod.No.
Coil spring for wheel suspension of the charges trailer HP500.01 and HP650.01
7669
39,95
Rivet for the mouning of the toggle holder for shirr of trailer tarpaulin
For use on trailers with sheet metal side walls.
material: aluminium rivet
diameter: 6 mm
length: 20 mm
for each retainer one piece will be needed
Cap for trailer hitch, black
Protection cap for ball of trailer hitch (towbar) of car
fit to ball diameter of 50 mm
protection cap made from black plastic
Overall height: 67 mm
Cap for trailer hitch, chromed
protection cap made from plastic with chromium plated surface
Cap for trailer hitch, chromed metall
protection cap made from chromium plated metall
with plastic clamping
Coil spring for trailer HP500, 650
Type: middle whorl diameter: 89mm
wire diameter: 11mm
total length: 165mm
ammount of whorls: 6
made in Germany
coupling joint for trailer with round towing bar (Ø=60mm)
Prod.No. 7326
Coupling joint for trailers made in GDR and a round towing bar with 60mm diameter of towing bar.
76,57
name: Rockinger KK92 B
mounting through two bolts M12
bolt distance: 54 mm
max. load on the coupling joint: 120 kg
for trailer with max. axle load of 1600 kg
total length: 23cm
made in Germany
1 piece will be needed
Seite 126 from178
coupling joint for trailer with round towing bar (Ø=70mm)
Prod.No.
7331
76,57
Coupling joint for trailers made in GDR and a round towing bar with 70mm diameter of towing bar.
name: Rockinger KK92 B
total length: 23cm
made in Germany
coupling joint for trailer with square towing bar (Ø=70mm)
Prod.No. 7332
76,57
Coupling joint for trailers made in GDR and a square towing bar with 60mmx60mm or made of of two
U-beam (like most HP300/HP350/HP400/HP450).
name: Rockinger KK92 F
total length: 23cm
made in Germany
elastic band (yard goods) D=8mm
Prod.No.
6763
1,70
Prod.No.
6760
1,80
Prod.No.
6761
3,55
Prod.No.
6762
4,48
Prod.No.
6757
5,30
elastic band
length: 1 m
diameter: circa 8 mm
colour: black
elastic band with hooks, 100 cm
elastic band with metall hook at each end
length: 100 cm
for fast fixation of blankets or tarpaulins or light load
length: 150 cm
colour: black
length: 200 cm (2 m)
colour: black
length: 30 cm
Seite 127 from178
Prod.No.
6758
1,45
Prod.No.
6759
1,67
Prod.No.
6732
122,00
length: 60 cm
length: 80 cm
flat tarpaulin for trailer HP 500
tarpaulin for trailer HP 500 with sheet metall side walls
length x wide: 170cm x 110cm
many different colours available
for other trailer with same dimendions, too
also for other trailer types and forms of tarpaulin (e.g. tent roof form) possible (we need a drawing or design) Please ask for
that!
made of high-grade truck tarpaulin
have the distinction of glossier surface of tarpaulin through additional finish and with a better self-cleaning effect
Gaiter for accumulating mechanisms trailer and camper
Prod.No. 7363
Rubber boot for the drawbar of the trailers and campers made in GDR.
The bellow protect the mechanic of the accumulating mechanisms against dust and spash water.
7,08
diameter of the hole 1: 60mm
length of the clamp mounting place next to hole 1: 35mm
diameter of the hole 1: 70mm
length of the clamp mounting place next to hole 1: 20mm
length total: 170mm
made in Germany
glas for three chamber rearlight, angularly, left hand
Prod.No.
7070
8,20
Prod.No.
6494
8,20
Glas for angulary model of the 3 chamber rearlight.
Fit to leftt hand base body.
Structure: left 21W flashing light, middle 5W rear light, right 21W stop light.
Fit to many IFA-vehicles and trailes.
made in Germany
dimension: 83mm x 210 mm
highness: 14 mm
glas for three chamber rearlight, angularly, right hand
Glas for angulary model of the 3 chamber rearlight.
Fit to right hand base body.
Structure: left 21W flashing light, middle 5W rear light, right 21W stop light.
made in Germany
highness: 14 mm
Seite 128 from178
Glas for three chamber rearlight, round, with number plate light
Prod.No.
6672
18,47
Prod.No.
6496
18,47
Prod.No.
7318
1,67
Glas for round model of the 3 chamber rearlight.
Structre: top 21W stop light, below 5W rear light, middle 21W flashing light.
The lower part is made transparent for number plate lighting.
Fit to many IFA-vehicles and trailer.
made in Germany
diameter glas: 135 mm
highness: 55 mm
Glas for three chamber rearlight, round, without number plate light
Glas for round model of the 3 chamber rearlight.
Structre: top 21W stop light, below 5W rear light, middle 21W flashing light.
Fit to many IFA-vehicles and trailer.
made in Germany
highness: 55 mm
large hook for elastic band
large hook to use together with elastic string
fit to many trucks and trailers (W50/L60, ROBUR, Barkas B1000 and many more)
made of galvanised sheet metal (thickness = 3mm)
with two mounting holes (diameter = 6,4 mm / well spacing = 45 mm)
wide total: 65 mm
hook wide: 16 mm
PVC cable 7 x 1,5 qmm (AWG16)
Prod.No.
6871
4,33
rubber cable 7 x 1,5 qmm (AWG16)
Prod.No.
6870
5,88
Prod.No.
7371
0,49
Prod.No.
6794
0,45
Solid rubber cable with seven single wires.
Screw for toggle retainer for shirr
Screw for the mouning of the toggle holder for shirr of trailer tarpaulin
For use on trailers with sheet metal side walls.
type: tapping screw
thread: use for timber
for each retainer one piece will be needed
sheet-metal eyelet for elastic band
sheet-metal eyelet to connect two ends of elastic band
length: 8 mm
inner diameter (oval): 8 x 13 mm
with electrogalvanized survace
one piece
Seite 129 from178
Shock absorber for Camper *Dübender Ei* (A1-70-150/15)
Prod.No. 7035
35,90
Telescopic shock absorber for wheel suspension of the small camper called *Dübener Ei* (Duebener
Egg, made in GDR)
Type: A1-70-150/15
mounting eye on both ends (inner diameter: 10mm)
short length: 186 mm (between center of mounting eyes)
extended length: 262 mm (between center of mounting eyes)
made in Germany
Shock absorber for overrun brake of trailer HP500 (E10-201-120/35)Prod.No.
7036
63,00
High-pressure pneumatic shock absorber for the overrun brake of the trailer type HP500 (made in
GDR)
Type: E10-201-120/35
inner diameter of upper mounting eye: 10 mm
Length of outer core barrel: 30 cm
extended length: 52,5 cm (between center of mounting eyes)
made in Germany
Shock absorber for trailer HP500
Prod.No.
Telescopic shock absorber for wheel suspension of the charges trailer HP 500.01/01
7115
39,50
Prod.No.
7543
39,50
Prod.No.
Telescopic shock absorber for wheel suspension of the charges trailer HP 500.01/01
7116
39,50
7367
9,08
Type: A2-150-80/50
made in Germany
Shock absorber for trailer HP650
Telescopic shock absorber for wheel suspension of the charges trailer HP 650
Type: B2-140-65/35
made in Germany
Shock absorber for trailer, torsion bar
Type: A2-150-80/50
made in Germany
Side light angular
Prod.No.
Front side light with plastic case.
Mounting can be easily by two screws holes diameter: 5mm.
Hole distance: 30mm.
Bulb (tubular lamp 5W)will be needed (not included of the delivery)
Good alternative for IFA vehicles, trailers and campers.
high quality
size bas plate: 62 x 62mm
size: 42 mm
lense: clear (withe light)
Seite 130 from178
Side light round
Prod.No.
7366
7,75
Prod.No.
7365
10,40
Prod.No.
7319
1,00
Prod.No.
7337
1,45
Prod.No.
7206
10,36
Prod.No.
1315
92,71
Front side light with plastic case.
Mounting can be easily by two screws holes diameter: 5mm.
Hole distance: 46mm.
high quality
diameter: 80mm
size: 41 mm
Side light round, metal housing
Front side light with firm metal case.
Mounting can be easily by the center bolt M6.
high quality
diameter: 67mm
size: 57 mm
slim hook for elastic band
small hook to use together with elastic string
fit to many trucks and trailers/camper
made of galvanised sheet metal (thickness = 2,5 mm)
with two mounting holes (diameter = 5,2 mm / well spacing = 20 mm)
wide total = hook wide: 13 mm
high total: 53 mm
Snap hook
metal hook for the universal useing.
length: 55mm
Spare glass for three chamber rearlight, round (new type)
New type of round model of the 3 chamber rearlight.
tarpaulin for trailer HP 3xx/ HP4xx
tarpaulin for trailer HP 300 and HP 400 with wooden side walls
also for other trailer types (HP300, HP400) and forms of tarpaulin (e.g. tent roof form) possible (we
need a drawing or design) Please ask for that!
have the distinction of glossier surface of tarpaulin through additional finish and with a better
self-cleaning effect
Seite 131 from178
tent roof tarpaulin for trailer HP 500
Prod.No.
6733
185,90
tarpaulin with tent roof form
fit to trailer HP 500 with sheet metall side walls
also for other trailer types possible (we need a drawing or design) Please ask for that!
have the distinction of glossier surface of tarpaulin through additional finish and with a better
self-cleaning effect
Three chamber rearlight, round (new type)
Prod.No. 7184
Replacement part for genuine part which undeliverable (NOT exactly the same dimensions!).
Complete component with carrier for bulbs.
Structre: top 21W stop light, below 5W rear light, midle 21W flashing light.
Fit to many IFA-vehicles.
18,44
made in Austria
highness: 89 mm
scope of delivery: without bulbs
Three chamber rearlight, round (new type), with number plate light Prod.No.
7205
18,84
Replacement part for genuine part which undeliverable (NOT exactly the same dimensions!).
Complete component with carrier for bulbs.
Structre: top 21W stop light, below 5W taillight, midle 21W flashing light and light for number plate at
the bottom.
made in Austria
highness: 89 mm
with two mounting bolts M6
scope of delivery: without bulbs
Three chamber rearlight, round right or left hand
Prod.No.
Round model of the 3 chamber rearlight. Complete component with carrier for bulbs.
Structre: top 21W stop light, below 5W rear light, midle 21W flashing light.
6493
29,13
made in Germany
diameter base body: 143mm
highness: 75 mm
Three chamber rearlight, angularly, left hand
Prod.No. 7071
15,36
Angulary model of the 3 chamber rearlight for left hand mounting. Complete component with carrier for
bulbs.
Structre: left 21W flashing light, middle 5W rear light, right 21W stop light.
Fit to many IFA-vehicles (for instance: Wartburg Trans, Trabant Kübel) and trailes.
made in Germany
highness: 60 mm
hole with rubber sealing for cable gland on lower back side left
Seite 132 from178
Three chamber rearlight, angularly, right hand
Prod.No.
Angulary model of the 3 chamber rearlight. Complete component with carrier for bulbs.
Structre: right 21W flashing light, middle 5W rear light, left 21W stop light.
Fit to many IFA-vehicles (for instance: Wartburg Trans, Trabant Kübel) and trailes.
6492
15,36
made in Germany
highness: 60 mm
hole with rubber sealing for cable gland on lower back side left
Prod.No.
Three chamber rearlight, angularly, with additional clear lense, left hand
6504
Angulary model of the 3 chamber rearlight. Complete component with carrier for bulbs.
Structre: right 21W flashing light, middle 5W rear light, left 21W stop light.
With additional clear lense at the middle of the rearlight case (for example: numberplate lighting)
15,72
only available for left hand
made in Germany
highness: 60 mm
hole with rubber sealing for cable gland on lower back side right
toggle retainer for shirr
Prod.No. 6571
0,55
toggle holder for shirr of trailer tarpaulin
(can be mounted with a fitting screw on side walls of trailer (for instance wooden side walls of trailer
type HP 300 and HP 400)
On top of the toggle is a blind hole to countersunk the screw head a little bit.
material: black plastic
diameter of mounting hole: 6 mm
high of toggle: 13,5 mm
diameter of the plane side (lying on the side wall): 25 mm
diameter of groove: 12 mm
diameter of collar (disabled the shirr to slip down): 20 mm
inner-diamter of countersunk: 12,7 mm
depth of countersunk: 2,5 mm
Triangular reflector red
Prod.No.
6869
2,99
Triangular reflector red/ black
Prod.No.
6868
1,99
Tube end piece for elastic band D=10mm
Prod.No.
7336
1,60
Metal tube with eye to mount elastic band with snap hooks
length: 73 mm
bore diameter (11 mm
Seite 133 from178
Prod.No.
7335
1,60
Prod.No.
7334
1,60
Prod.No.
7245
12,85
Prod.No.
7246
49,50
Prod.No.
7317
1,83
1103
8,73
7417
12,30
length: 58 mm
bore diameter (7,5 mm
length: 70 mm
bore diameter (9 mm
Tube for wheel (trailer HP3xx/HP4xx)
Tube for small 8?-rims of trailer typs HP300, HP350, HP400 and HP450
made in Germany
Tyre 4.00-8 for trailer wheel (HP3xx/HP4xx)
Tyre for the small 8?-rims of trailer typs HP300, HP350, HP400 and HP450
made in Germany
W50 hook for elastic band
special hook to use together with elastic string
fit to many trucks and trailers (W50/L60, ROBUR, Barkas B1000 and many more)
made of galvanised sheet metal
with two mounting holes (diameter: 5mm / well spacing: 34mm
Trailer > Bastei-camper
brake hose for trailer/camper
Prod.No.
brake hose for camper Bastei and Camper
maybe also fit to other types of trailer/ camper (for technical specifications see below)
length ca. 50 cm
type of thread: M10x1
1x female thread
1x male thread
Brake tube 1430mm
Prod.No.
Brake line made of NiCu for Bastei.
Complete pre mounted inclusive two Screw-caps.
diameter: 4,75mm
lenght: 143 cm
made in Germany
Seite 134 from178
Brake tube 600mm
Prod.No.
6942
8,30
Prod.No.
7427
10,20
outer wheel bearing (Bastei/Intercamp/Oase)
Prod.No. 6988
Outer tapered roller bearing for wheel bearing of camper Bastei and Camper Intercamp/ Oase
9,12
outer wheel bearing (Bastei/Intercamp/Oase)
9,64
Brake line made of NiCu for Bastei.
Complete pre mounted inclusive two Screw-caps.
diameter: 4,75mm
lenght: 600mm
made in Germany
Handbrake cable, Bastei
handbrake cable for for the camper Bastei.
Both cables are symmetric and have the same length
the complete lenght is 160 cm
Prod.No. 6989
Inner tapered roller bearing for wheel bearing of camper Bastei and Camper Intercamp/ Oase
For one wheel you will need one piece of that bearing (two pieces for hole axle)
Shock absorber for overrun brake of Bastei (A1-70-150/15)
Prod.No. 7034
Telescopic shock absorber for the overrun brake of the camper type Bastei (made in GDR)
35,90
Type: A1-70-150/15
mounting eye on both ends (inner diameter: 10mm)
short length: 186 mm (between center of mounting eyes)
extended length: 262 mm (between center of mounting eyes)
made in Germany
Weel-brake cylinder,
Prod.No. 6729
39,50
Wheel brake cylinder with piston-diameter: 25,35 mm for the hydraulic wheel brake system of the DDR
camper typ: Bastei.
Wheel brake cylinder, rear axle, original, D=25,35mm
Prod.No. 7316
28,50
Complete in Germany overhauled rear wheel brake cylinder with ring sleeves, brak-piston
D=25,35mm.
Mark: IFA BHL
scope of delivery: inclusive ring sleeves, dust caps and bleeder screw)(break piston diameter: 25,35
mm
Trailer > Camptourist / Klappfix
Seite 135 from178
shaft seal 35 x 62 x 7
Prod.No.
6395
5,98
shaft seal 35 x 62 x 7
simple version without dust lip
for ball bearings (wheel bearing) of camptourist/Klappfix trailer and Qek campers only with mechanical overrun brake
Not fit to these trailer/camper if hydraulical brake system built in
shaft seal 35 x 62 x 7 with dust lip
Prod.No.
6396
6,52
shaft seal 35 x 62 x 7 with additional dust lip
for ball bearings (wheel bearing) of camptourist/Klappfix trailer and Qek campers only with mechanical overrun brake
Not fit to these trailer/camper if hydraulical brake system built in
protects the sealing lips better from brake dust
shaft seal 40 x 62 x 10 with dust lip
Prod.No.
6978
9,95
shaft seal 40 x 62 x 10 with additional dust lip
for ball bearings (wheel bearing) of camptourist/Klappfix trailer and Qek campers only with hydraulical
overrun brake
Not fit to these trailer/camper if mechanical brake system is built in.
protects the sealing lips better from brake dust
Prod.No. 7037
Shock absorber for overrun brake of fold tent camper *Camptourist* (E10-201-210/55)
63,00
High-pressure pneumatic shock absorber for the overrun brake of the fold tent trailer type Camptourist
(made in GDR)
Type: E10-201-210/55
Length of outer core barrel: 30 cm
extended length: 52,5 cm (between center of mounting eyes)
made in Germany
Telescopic shock absorber Alpenkreuzer
Prod.No.
7179
41,17
Prod.No.
6966
36,67
Prod.No.
7117
41,17
Shock absorber for the trailer axle model Alpenkreuzer with coil spring.
Marking / type: B2-112-140/45
scope of delivery:
Made in Germany
Telescopic shock absorber for Camptourist and Klappfix
Shock absorber for the trailer axle model Alpenkreuzer with leaf spring.
Marking / type: B2-140-65 / 30
scope of delivery:
Made in Germany
Telescopic shock absorber for Camptourist and Klappfix
Shock absorber for the trailer axle model Alpenkreuzer with coil spring.
Marking / type: B2-112-140/ 65
scope of delivery:
Made in Germany
Trailer > Intercamp / Oase
Seite 136 from178
Brake drum 50mm
Prod.No.
6967
42,95
Prod.No.
6968
9,32
Prod.No.
6977
35,57
Drum fit to the wheel brake of the camper *Intercamp*
The brake shoewidth is 50mm
bolt circle 4 x 160mm
inside diameter: 230mm
made in EU
Brake shoe 50mm
Brake shoe complete, with lining
brake drums with inner diameter of 230 mm
wide: 50mm
tatal 4 pieces will be needed
for brake drumin connection with wheel brake cylinder
Brake shoe set, rear axle, 50mm
fit to camper Bastei and Intercamp / Oase
wide: 50 mm
contents:
Master brake cylinder - one circle, complete
Prod.No. 6945
68,00
Used in braked version of camper with hydraulical brake system (QEK Junior/Aero, Bastei,
Intercamp/Oase)
new produced, made in EU
to use this master break cylinder one reservoir for brake fluid will be needed
Master brake cylinder - one circle, original
Prod.No. 7190
62,00
Used in braked version of camper with hydraulical brake system (QEK Junior/Aero, Bastei,
Intercamp/Oase)
overhauled spare part
delivery without reservior for brake fluid and mounting equipment
Please note, we can only exchange you this spare part if you ship 1x used master brake cylinder with
the type number TGL BH7 to our company in advance!
to use this master break cylinder one reservoir for brake fluid will be needed
Prod.No.
6412
31,20
Prod.No.
6947
3,95
Profile for external door-duct weather strip.
length: 6 meter
made in Germany
Fit for camper "Intercamp"
Seite 137 from178
Ring sleeve, for wheel brake cylinder, complete
Prod.No.
6943
6,83
Prod.No.
7623
83,84
Prod.No.
7285
14,25
Ring sleeve, for wheel brake cylinder.
Fit to camper Bastei and Intercamp/Oase
One set will be needed for each wheel side
Sealing rubber set Intercamp/ Oase
Profile rubber for the front and rear pans of the camper Intercamp and Oase.
Set consitst of one piece of 8,5m sealingrubber (black).
For each pane one piece of 4,25m will be needed.
made in Germany
Sleeve set single brake master cylinder, original, trailer
Complete repair set for the 1-circle brake master cylinder.
The sleeves was mounted up to vinatge april 1980 at Trabant 601.
material: rubber
made in Germany
Sleeve set single brake master cylinder, trailers
Prod.No. 6946
10,45
Complete repair set for the original 1-circle brake master cylinder (not fit to our new manufactured
master breake cylinder).
material: rubber
made in EU
Telescopic shock absorber
Prod.No. 6944
40,13
Shock absorber VK350 + 351for the camper types Bastei,Intercamp/Oase and Qek Junior + Aero
(made in GDR).
Buffer Type: A2-150-160/50
made in Germany
Weel-brake cylinder, M10x1
Prod.No.
6730
39,50
Wheel brake cylinder for hydraulic brake system of trailer
if brake shoe is 50 mm and inner diameter of brake drum is 230 mm
piston-diameter: 25,35 mm
connection thread for brake hose/ brake line: M10x1
Trailer > Qek-camper
Seite 138 from178
Coil spring Qek Junior / Aero
Prod.No.
6773
56,33
Prod.No.
7353
134,33
Prod.No.
6987
4,69
Prod.No.
6986
5,54
Prod.No.
6993
89,20
Prod.No.
6439
1,22
Spring for the Qek caravan axle.
Fit to the models Junior and Aero.
made in Germany
Sealing rubber set
Profile rubber for all pans of the camper Qek Junior.
Set consitst of rubber (black) and filler (black)
made in Germany
Trailer > Qek-camper > brake system
Brake hose longer, Qek
Extended brake hose for Qek camper with hydraulical brake system
Length total: 225 mm
one side with core thread port M10x1
other side with external thread port M10x1
Brake hose short, Qek camper
short brake hose with female and male thread connection
To connect the distributor with brake line of Qek camper
thread: M10 x 1
length complete: 18 cm
lever for parking brake
handbrake lever for the parking brake of the caravan Qek.
delivery inclusive unkock push button and toothed segment
Bulbs
Bulbs > 12Volt
Bulb 12V / 15W ( white )
bulb for flasher stop tail lamp and flashing indicator lamp of veteran cars
for voltage of 12V
power consumption: 15W
base typ: BA 15s
Seite 139 from178
Bulb ( ) 12V / 21W ( orange )
Prod.No.
131
Light bulb with yellow coloured glass. Can be used for many vehicles.
Mostly use as flasher stop tail lamp and flashing indicator lamp (clear class indicator lenses)
2,48
technical data:
for voltage of 12V
21W
colour: orange
base of lamp: BA 15s
Bulb ( flasher stop tail lamp and flashing indicator lamp ) 12V / 21W Prod.No.
( white )
Bulb ( tubular lamp ) 12V 10W, 11x35
130
1,12
Prod.No.
7404
1,13
Prod.No.
7487
1,13
Longish bulb with one integrated filaments.
Can be used at many vehicles.
To be the ideal thing for a lot of Young- and Oldtimers.
technical data:
voltage: 12V
power: 10 Watt
colour: colourless (clear/withe)
base type: SV8,5-8
length total: 37mm
length of cylindrical glass (without metall caps): 19mm
diameter of the glass cylinder: 11mm
diameter of metall end cap: ca. 8,5mm
single filamentsbulb
Bulb ( tubular lamp ) 12V 10W, 11x41
technical data:
voltage: 12V
power: 10 Watt
base type: SV8,5-8
length total: 43mm
Seite 140 from178
Bulb ( tubular lamp ) 12V 18W
Prod.No.
7405
1,25
Prod.No.
7406
2,09
Prod.No.
135
1,13
technical data:
voltage: 12V
power: 18 Watt
base type: SV8,5-8
length total: mm
length of cylindrical glass (without metall caps): mm
diameter of the glass cylinder: mm
technical data:
voltage: 12V
power: 3 Watt
base type: S6
length total: mm
technical data:
voltage: 12V
power: 5 Watt
base type: SV8,5-8
length total: 36...37mm
Seite 141 from178
Prod.No.
7407
2,49
technical data:
voltage: 12V
power: 7 Watt
base type: SV8,5
length total: mm
Bulb 12 V / 1,2W
Prod.No.
144
1,98
Very small (mini) bulb with glass base used for many Young-and Oldtimer for the control lamp
for example switch for flashing warning lights, instrument panel lightings, speedometer lights
e.c.
voltage: 12W
power: 1,2 Watt
base type: W2 x 4,6D
length total: 17 mm ? 19mm
diameter: 4,8mm
Bulb 12V / 2W BA7s
Prod.No.
151
1,04
Bulb used for many Young-and Oldtimer for the control lamp for example switch for flashing warning
lights, instrument panel lightings, speedometer light e.c.
single filaments: 2W
bas type: BA 7s
voltage: 12V
Bulb 12V / 2W BA9s
Prod.No.
147
1,04
lights, instrument panel lightings, speedometer light, parking lights e.c.
single filaments: 2W
base type: BA 9s
voltage: 12V
Bulb H1 12V / 55W ( high beam )
Bulb H1 12V / 100W ( high beam )
Prod.No.
155
4,75
Prod.No.
156
7,92
Prod.No.
161
9,28
Made in Germany
without advisory opinion
Bulb H1 12V / 55W Xenon blue
Seite 142 from178
Bulb H3 12V / 100W for fog lamp
Prod.No.
158
3,50
Bulb H3 12V / 55W for fog lamp
Prod.No.
157
5,09
Prod.No.
162
9,28
Made in Germany
without advisory opinion
Bulb H4 12V 60/55W
Prod.No.
145
3,99
Halogen bulb with two integrated filaments.
Can be used at many vehicles as insert for the head lights combinated for dipped headlights and high
beam.
technical data:
voltage: 12V
power: 60W und 55W
base type: P43t (Standard-Sockel für H4-Lampen
Bulb H4 12V 100/80W
Prod.No.
146
7,98
Prod.No.
160
9,44
Spezial bulb with blue glass cylinder to projected an Xenon lightning effect.
With two integrated filaments.
beam.
technical data:
voltage: 12V
power: 60W und 55W
colour: Xenon blue
Bulb R2 12V 45/40W
Prod.No.
150
2,61
Bilux bulb with two integrated filaments.
beam.
technical data:
voltage: 12V
power: 60W und 55W
total lengtht: 74mm
diameter socketring: 45mm
max. diameter of the galss ball : 40mm
base type: P43t
Seite 143 from178
Bulb red, ( tubular lamp ) 12V 5W
Prod.No.
136
2,20
Prod.No.
132
2,48
technical data:
voltage: 12V
power: 5 Watt
colour: red
base type: SV8,5-8
Bulb red, 12V / 21W
Light bulb with red coloured glass. Can be used for many vehicles.
Mostly use as stop lamp or fog tail lights.
fit to most vehicle types (all with base of lamp: BA 15s).
for voltage of 12V
21W
colour: red
Bulb with socket 12 V / 1,2W
Prod.No. 6402
2,98
Bulb with glass base and inclusive socket used for many Young-and Oldtimer for the control
lamp for example switch for flashing warning lights, instrument panel lightings, speedometer
lights e.c.
voltage: 12W
power: 1,2 Watt
base type: W2 x 4,6D
length total: 17 mm ? 19mm
diameter: 4,8mm
single filamentsbulb inclisive socket base holder
Flashing indicator bulb 12V 21W ( white )
Prod.No.
72
Can be used at many vehicles as insert of the flashing indicator lamps with orange-colored lenses.
1,59
technical data:
voltage: 12V
power: 21 Watt
base type: SV8,5-8
Seite 144 from178
Flashing indicator bulb, orange 12V 21W
Prod.No.
73
Can be used at many vehicles as insert of the flashing indicator lamps with orange-colored lenses.
2,08
technical data:
voltage: 12V
power: 21 Watt
colour: orange (yellow)
base type: SV8,5-8
Lamp spare kit H4 / 12V
Prod.No.
7057
8,55
Prod.No.
6623
14,68
Prod.No.
6922
0,98
content:
1x H4-lamp 60/55W with base P43t
1x bulb for speedometer 2W with base BA 7s
1x Torpedo-fuse 8A
1x Torpedo-fuse 16A
Lamp spare kit R2 / 12V
content:
1x R2-lamp 45/40W with base P45t
1x bulb for speedometer 2W with base BA 7s
1x Torpedo-fuse 8A
1x Torpedo-fuse 16A
Ligth bulb (double function) 12V 5W/ 21W
Light bulb with two integeated filaments.
Fit to new type of rear lamp with double function (brake light and rear light)
Technical data:
voltage: 12V
power: 5W hot-wire (for rear light) and 21W hot-wire (for brake light)
socket type: BAY15d
ECE-notation: P21/5W
length total: 47mm
diameter socket: 15mm
max. diameter glas bulb: 25mm
Seite 145 from178
Ligth bulb (double function) RED 12V 5W/ 21W
Prod.No. 6923
3,74
Light bulb red with two integeated filaments.
Fit to new type of rear lamp with double function (brake light and rear light) in connection with clear
rear light lenses.
Technical data:
voltage: 12V
power: 5W hot-wire (for rear light) and 21W hot-wire (for brake light)
socket type: BAY15d
ECE-notation: P21/5W
length total: 47mm
diameter socket: 15mm
max. diameter glas bulb: 25mm
X-treme Bulb H4 12V 60/55W
Prod.No. 7401
11,73
High power halogen bulb with two integrated filaments.
Can be used at many vehicles as insert for the head lights combinated for dipped headlights
and high beam.
The edge of the high power H4 is 80% more light against standart H4 by the same power rate.
technical data:
voltage: 12V
power: 60W und 55W
Bulbs > 12Volt > bulb for parking lamp
Bulb ( parking lamp )
12 V / 5W ( white )
12V / 4W ( blue )
12V / 4W ( white )
Prod.No.
143
1,16
Prod.No.
139
1,61
Prod.No.
138
0,97
Prod.No.
6440
1,44
Prod.No.
120
1,34
Prod.No.
7578
2,45
Bulbs > 6Volt
Bulb
6V / 18W
bulb for veteran cars
for example flasher stop tail lamp and flashing indicator lamp
Bulb 6V / 21W
flasher stop tail lamp and flashing indicator lamp
Bulb 6V / 21W, orange
indicator lamp
Seite 146 from178
Bulb 6V 2W
Prod.No. 7374
2,55
Bulb with glass base used for many Young-and Oldtimer for the control lamp for example
switch for flashing warning lights, instrument panel lightings, speedometer light e.c.
single filaments: 2 Watt
base type: W2 1x9 5D
voltage: 6V
Bulb 6V 3W
Prod.No. 7375
1,40
Bulb with glass base used for many Young-and Oldtimer for the control lamp for example switch for flashing warning lights,
instrument panel lightings, speedometer light e.c.
base type: W2 1x9 5D
voltage: 6V
Bulb ( control lamp, instrument panel lighting )
Prod.No. 7251
1,40
6V / 1,2W
lights, instrument panel lightings, speedometer light e.c.
single filaments: 1,2W
base type: BA 7s
voltage: 6V
Bulb ( tubular lamp )
6 V / 5W
Prod.No.
121
1,34
Bulb 6V 2W
Prod.No. 7373
1,40
Bulb used for many Young-and Oldtimer for the control lamp for example switch for flashing warning lights, instrument
panel lightings, speedometer light e.c.
base type: BA 9s
voltage: 6V
Bulb 6V / 0,6W
Prod.No.
123
1,40
Bulb used for many Young-and Oldtimer for the control lamp, instrument panel lightings, speedometer
light e.c.
single filaments: 0,6W
bas type: BA 7s
voltage: 6V
Bulb R2 6V 45 / 40W
Prod.No.
124
5,85
Prod.No.
white cylindrical bulb for use in flashing indicator lamps with orange-colored glasses
6V / 6W
hole length: ca. 43mm
diameter of cylindrical glass: 14mm
133
2,25
Biluxbulb used for many Young-and Oldtimer for the headlights.
Bulbtype: two filaments, 1x low beam light (40W), 1x high beam (45W)
bas type: P45t
voltage: 6V
Flashing indicator bulb 6V 18W ( white )
Seite 147 from178
Flashing indicator bulb 6V 18W ( yellow )
Prod.No.
orange-colored cylindrical bulb for use in flashing indicator lamps with white glasses
6V / 18W
hole length: ca. 43mm
diameter of cylindrical glass: 14mm
134
2,67
Prod.No.
6835
1,34
Prod.No.
6881
2,55
Prod.No.
122
1,19
Prod.No.
red Bulb ( flasher stop tail lamp and flashing indicator lamp ) 6V / 21W
6445
2,38
148
3,77
Light bulb
6 V / 5W (Ba15s)
Ball bulb with bayonet socket Ba15s
fit to operating voltage of 6V
power: 5W
for using in back light lamps
Light bulb
6 V / 5W (Ba15s) colour: red
Ball bulb with bayonet socket Ba15s
fit to operating voltage of 6V
power: 5W
with red stained glass
for using in back light lamps
Light bulb ( parking lamp )
6V / 4W
red colored bulb
6V / 21W
Bulbs > 24 Volt
Prod.No.
To be the ideal thing for a lot of Young-, Oldtimers and lorrys
technical data:
voltage: 24W
power: 15 Watt
base type: SV8,5-8
length total: 45mm
diameter of the glass cylinder: 14,5mm
Seite 148 from178
Prod.No.
7403
3,90
Prod.No.
137
1,23
Prod.No.
7402
1,98
technical data:
voltage: 24W
power: 20 Watt
base type: SV8,5
Bulb ( tubular lamp ) 24 V / 5W , C5W
technical data:
voltage: 24W
power: 5 Watt
base type: SV8,5
length total: 37mm
Bulb 24V 3W
technical data:
voltage: 24W
power: 3 Watt
base type: S6
length total: mm
diameter of metall end cap: ca. mm
Seite 149 from178
Bulb 24V 3W Ba7s
Prod.No.
7616
1,60
Prod.No.
7663
4,50
Prod.No.
7664
5,27
Prod.No.
6875
4,19
Ball bulb with one integrated filaments and metal socket.
Can be used at many vehicles for instand as display or parking lights.
technical data:
voltage: 24W
power: 3 Watt
base type: BA7S
length total: 20mm
length of the metal base: 11mm
Bulb H3 24V 70W Pk22s
Can be used at many vehicles for instand as fog lamp or high beam lights.
technical data:
voltage: 24W
power: 70 Watt
base type: BA7S
length total: 41mm
length of the connection wire: 95mm
Bulb H7 24V 100W Px26d
Can be used at many vehicles for instand as fog lamp or high beam lights.
technical data:
voltage: 24W
power: 100 Watt
base type: Px26d
length total: 57mm
connection pins for two flat plugs
connecting wire and asseccory
plastic protection hose 10mm (á 1,0m)
two-part protection pipe made of plastic
inner diameter: 10mm
colour: black
Seite 150 from178
Prod.No.
6884
7,63
Prod.No.
6885
11,23
Prod.No.
6886
14,50
inner diameter: 14mm
colour: black
colour: black
colour: black
Polyester fleece adhesive tape, 19mm, 10 meter
Prod.No. 6810
3,96
Non-woven polyester fleece of high quality, embossed on the back, in combination with a strong
rubber-based adhesive.
Colour: black
Widht: 19 mm
Lenght: 10 meter
Rubber membrane plug for holes with diameter of 22,5mm
Prod.No. 6896
1,26
Membrane plug made of black rubber (Polychloropren) to shut round holes in car bodys (such as
service holes) or as variable cable grommet seal for some wires (also with plugs)
fit to hole diameter of 22,5 mm
inner diameter of membrane (max. usable diameter): 16 mm
outer diameter (total): 28 mm
thickness: 7 mm
connecting wire and asseccory > bicolored car wires
connecting wire and asseccory > bicolored car wires > 0,75 mm² wire size
FLY/FLRY car wire, 0,75 mm² (AWG18), blue-green, yard goods
Prod.No.
6956
0,45
Prod.No.
6955
0,45
FLY/FLRY car wire, 0,75 mm² (AWG18), blue-white, yard goods
Prod.No.
6954
0,45
FLY/FLRY car wire, 0,75 mm² (AWG18), brown-white, yard goods
Prod.No.
6951
0,45
FLY/FLRY car wire, 0,75 mm² (AWG18), grey-black, yard goods
Prod.No.
6957
0,45
FLY/FLRY car wire, 0,75 mm² (AWG18), grey-grün, yard goods
Prod.No.
6958
0,45
FLY/FLRY car wire, 0,75 mm² (AWG18), red-blue, yard goods
Prod.No.
6953
0,45
FLY/FLRY car wire, 0,75 mm² (AWG18), red-yellow, yard goods
Prod.No.
6952
0,45
FLY/FLRY car wire, 0,75 mm² (AWG18), blue-red, yard goods
connecting wire and asseccory > bicolored car wires > 1,5 mm² wire size (AWG16)
Seite 151 from178
FLRY car wire, 1,5 mm² (AWG16), blue-black, yard goods
Prod.No.
7650
0,66
FLRY car wire, 1,5 mm² (AWG16), blue-brown, yard goods
Prod.No.
7646
0,66
FLRY car wire, 1,5 mm² (AWG16), blue-green, yard goods
Prod.No.
7648
0,66
FLRY car wire, 1,5 mm² (AWG16), blue-red, yard goods
Prod.No.
7649
0,66
FLRY car wire, 1,5 mm² (AWG16), blue-white, yard goods
Prod.No.
7651
0,66
FLRY car wire, 1,5 mm² (AWG16), blue-yellow, yard goods
Prod.No.
7647
0,66
Prod.No.
6807
0,66
FLRY car wire, 1,5 mm² (AWG16), brown-blue, yard goods
Prod.No.
7652
0,66
FLRY car wire, 1,5 mm² (AWG16), brown-green, yard goods
Prod.No.
7653
0,66
FLRY car wire, 1,5 mm² (AWG16), brown-red, yard goods
Prod.No.
7654
0,66
FLRY car wire, 1,5 mm² (AWG16), brown-white, yard goods
Prod.No.
7655
0,66
FLRY car wire, 1,5 mm² (AWG16), yellow-black, yard goods
Prod.No.
7691
0,66
FLRY car wire, 1,5 mm² (AWG16), yellow-blue, yard goods
Prod.No.
7688
0,66
FLRY car wire, 1,5 mm² (AWG16), yellow-green, yard goods
Prod.No.
7689
0,66
FLRY car wire, 1,5 mm² (AWG16), yellow-red, yard goods
Prod.No.
7690
0,66
FLRY car wire, 1,5 mm² (AWG16), yellow-white, yard goods
Prod.No.
7692
0,66
FLY/FLRY car wire, 1,5 mm² (AWG16), black-blue, yard goods
Prod.No.
7693
0,66
FLY/FLRY car wire, 1,5 mm² (AWG16), black-brown, yard goods
Prod.No.
7694
0,66
Prod.No.
6843
0,66
Prod.No.
7695
0,66
Prod.No.
6805
0,66
Prod.No.
7696
0,66
Prod.No.
6808
0,66
FLRY car wire, 1,5 mm² (AWG16), brown-black, yard goods
FLY/FLRY car wire, 1,5 mm² (AWG16), black-green, yard goods
FLY/FLRY car wire, 1,5 mm² (AWG16), black-grey, yard goods
FLY/FLRY car wire, 1,5 mm² (AWG16), black-red, yard goods
FLY/FLRY car wire, 1,5 mm² (AWG16), black-violet, yard goods
FLY/FLRY car wire, 1,5 mm² (AWG16), black-white, yard goods
Seite 152 from178
FLY/FLRY car wire, 1,5 mm² (AWG16), black-yellow, yard goods
Prod.No.
6844
0,66
FLY/FLRY car wire, 1,5 mm² (AWG16), brown-yellow, yard goods
Prod.No.
6806
0,66
FLY/FLRY car wire, 1,5 mm² (AWG16), green-black, yard goods
Prod.No.
6804
0,66
FLY/FLRY car wire, 1,5 mm² (AWG16), green-red, yard goods
Prod.No.
6803
0,66
FLY/FLRY car wire, 1,5 mm² (AWG16), white-black, yard goods
Prod.No.
6845
0,66
FLY/FLRY car wire, 1,5 mm² (AWG16), white-red, yard goods
Prod.No.
6809
0,66
connecting wire and asseccory > Single colour wire
connecting wire and asseccory > Single colour wire > 0,75 mm² wire size
FLY/FLRY car wire, 0,75 mm² (AWG16), black, yard goods
Prod.No. 6959
0,45
Spezial care cable with black PVC-isolation and an wire cross section from 0,75 mm².
Can be used to creat new cable harnesses, to change single wires or to repair demaged wiring looms.
made in Germany
colour: black
strand: copper
FLY/FLRY car wire, 0,75 mm² (AWG16), blue, yard goods
Prod.No.
6964
0,45
FLY/FLRY car wire, 0,75 mm² (AWG16), brown, yard goods
Prod.No. 6990
0,45
Spezial care cable with brown PVC-isolation and an wire cross section from 0,75 mm².
made in Germany
colour: brown
strand: copper
Seite 153 from178
FLY/FLRY car wire, 0,75 mm² (AWG16), green, yard goods
Prod.No. 6962
0,45
Spezial care cable with green PVC-isolation and an wire cross section from 0,75 mm².
made in Germany
colour: green
strand: copper
FLY/FLRY car wire, 0,75 mm² (AWG16), grey, yard goods
Prod.No. 6965
0,45
Spezial care cable with grey PVC-isolation and an wire cross section from 0,75 mm².
made in Germany
colour: grey
strand: copper
FLY/FLRY car wire, 0,75 mm² (AWG16), rot, yard goods
Prod.No.
6963
0,45
FLY/FLRY car wire, 0,75 mm² (AWG16), white, yard goods
Prod.No. 6960
0,45
Spezial care cable with white PVC-isolation and an wire cross section from 0,75 mm².
made in Germany
colour: withe
strand: copper
FLY/FLRY car wire, 0,75 mm² (AWG16), yellow, yard goods
Prod.No. 6961
0,45
Spezial care cable with yellow PVC-isolation and an wire cross section from 0,75 mm².
made in Germany
colour: yellow
strand: copper
connecting wire and asseccory > Single colour wire > 1,5 mm² wire size (AWG16)
Prod.No. 6616
0,53
Spezial care cable with black PVC-isolation and an wire cross section from 1,50mm².
made in Germany
colour: black
strand: copper
Prod.No. 6618
0,53
Spezial care cable with blue PVC-isolation and an wire cross section from 1,50mm².
made in Germany
colour: blue
strand: copper
Seite 154 from178
Prod.No. 6615
0,53
Spezial care cable with brown PVC-isolation and an wire cross section from 1,50mm².
made in Germany
colour: brown
strand: copper
FLY/FLRY car wire, 1,5 mm² (AWG16), gray, yard goods
Prod.No.
Spezial care cable with gray PVC-isolation and an wire cross section from 1,50mm².
7144
0,53
made in Germany
colour: gray
strand: copper
Prod.No. 6801
0,53
Spezial care cable with green PVC-isolation and an wire cross section from 1,50mm².
made in Germany
colour: green
strand: copper
FLY/FLRY car wire, 1,5 mm² (AWG16), orange, yard goods
Prod.No. 6802
0,53
Spezial care cable with orange PVC-isolation and an wire cross section from 1,50mm².
made in Germany
colour: orange
strand: copper
FLY/FLRY car wire, 1,5 mm² (AWG16), pink, yard goods
Prod.No.
Special care cable with pink PVC-isolation and an wire cross section from 1,50mm².
7645
0,53
made in Germany
colour: pink
strand: copper
FLY/FLRY car wire, 1,5 mm² (AWG16), red, yard goods
Prod.No. 6617
0,53
Spezial care cable with red PVC-isolation and an wire cross section from 1,50mm².
made in Germany
colour: red
strand: copper
FLY/FLRY car wire, 1,5 mm² (AWG16), violet, yard goods
Prod.No.
Special care cable with violet PVC-isolation and an wire cross section from 1,50mm².
7644
0,53
made in Germany
colour: violet
strand: copper
Seite 155 from178
Prod.No. 6614
0,53
Spezial care cable with green PVC-isolation and an wire cross section from 1,50mm².
made in Germany
colour: gelb
strand: copper
Prod.No. 6098
0,79
made in Germany
colour: black
strand: cop
Prod.No.
Spezial care cable with blue PVC-isolation and an wire cross section from 2,5 mm².
7142
0,79
7143
0,79
made in Germany
colour: blue
strand: cop
Prod.No.
Spezial care cable with brown PVC-isolation and an wire cross section from 2,5 mm².
made in Germany
colour: brown
strand: cop
Prod.No. 6097
0,79
Spezial care cable with green PVC-isolation and an wire cross section from 2,5 mm².
made in Germany
colour: green
strand: cop
Prod.No. 6096
0,79
Spezial care cable with red PVC-isolation and an wire cross section from 2,5 mm².
made in Germany
colour: red
strand: cop
FLY/FLRY car wire, 2,5 mm² (AWG14), white, yard goods
Prod.No.
Spezial care cable with withe PVC-isolation and an wire cross section from 2,5 mm².
7140
0,79
made in Germany
colour: withe
strand: cop
Seite 156 from178
Prod.No.
7141
0,79
made in Germany
colour: yellow
strand: cop
Prod.No. 6104
1,05
made in Germany
colour: black
strand: copper
Prod.No.
Spezial care cable with blue PVC-isolation and an wire cross section from 4,00 mm².
7138
1,05
made in Germany
colour: blue
strand: copper
Prod.No. 6099
1,05
Spezial care cable with red PVC-isolation and an wire cross section from 4,00 mm².
made in Germany
colour: red
strand: cop
Prod.No.
7139
1,05
made in Germany
colour: yellow
strand: copper
connecting wire and asseccory > manufactured wires
Car battery wire 0,74m
Prod.No. 7592
15,50
Connection cable between the negative pole of car battery and the terminal screw of starter.
Best use for IFA vehicles.
Please note: it is an NOS part and at some wires it is possible that the isolating bushing for the plus
pole is demaged or not mounted. This will be no reason for complaints !
for 6V and 12V or 24V
pre-finished
length total: 720mm
original spare part
Seite 157 from178
Prod.No. 7591
13,28
Connection cable between the negative pole of car battery and the terminal screw for enigine /
gearbox.
Please note: it is an NOS part and at some wires it is possible that the isolating bushing for the minus
pre-finished
length total: 920mm
one cable tail with 8mm cable shoe for terminal screw of enigine / gearbox
original spare part
Prod.No. 7438
15,55
Connection cable between the negative pole of car battery and the terminal screw for enigine /
gearbox.
Please note: it is an NOS part and at some wires it is possible that the isolating bushing for the minus
for 6V and 12V
pre-finished
length total: 1,05m
one cable tail with 8mm cable shoe for terminal screw of enigine / gearbox
original spare part
Prod.No. 7588
16,50
for 6V and 12V oder 24V
pre-finished
length total: 1150mm
original spare part
Prod.No. 7587
24,30
pre-finished
length total: 2480mm
original spare part
Seite 158 from178
Car wire black-green-red
Prod.No.
7722
0,99
Prod.No.
7437
0,99
Prod.No.
7721
0,99
Three coloured pree mounted car wire.
Universal useable, fit to many Old-and Youngtimers
technical details:
colour: black, green, red
wire size: 1,5mm²
length: 510mm
connection on both ends: stripped and tin-plated
Wire brown, flat-O-plug
Pree mounted car wire.
technical details:
colour: brown
wire size: 1,5mm²
length: 248mm
connection 1: O-plug hole diameter: 5mm
connection 2: flat plug 6,3 x 0,8
Wire brown, flat-plug-flat-plug
Pree mounted car wire.
technical details:
colour: brown
wire size: 1,5mm²
length: 320mm
connection on both ends: flat plug 6,3 x 0,8
workshop requirement
2K Hi-Speed Primer Filler 200ml
Prod.No. 6906
16,17
ColorMatic 2K Hi-Speed fill primer can be universelly applied on all steel, zinc-plated sheet steel and
aluminium with excellent adhesion and rust prevension. Very fast air drying: 45 min (20°C). Easy to sand, wet
and dry. Resistant against solvent. Free of isocyanate.
If both components are mixed the pot life will take 8 houres at least.
Aluminium-sealing ring 20 x 16 x 1,5 mm
Prod.No.
6429
0,18
Prod.No.
7702
21,30
Aluminium sealing ring, massive
construction type A
DIN 7603
Brake pipe spanner 10-11mm angled
Special tool for mounting or demounting of screw-cap for brakelines.
type: level angleded
Fit to brake screws SW10 and SW11.
Seite 159 from178
Brake pipe spanner 10-11mm, straight
Prod.No.
7703
9,90
Prod.No.
6253
22,75
Prod.No.
6252
1,99
Prod.No.
7033
19,92
Cleaning and maintenance agent for electrical connectors and components,Prod.No.
200ml
7094
2,65
7054
0,85
Special tool for mounting or demounting of screw-cap for brakelines.
type: sraight
Fit to brake screws SW10 and SW11.
brake-cleaner 5 Liter
quick-cleaner for brake and clutch parts
content: 5 litre
brake-cleaner 600ml
Special offerquick-cleaner for brake and clutch parts
CKW free
volume: 600 ml
brake-cleaner, one packing unit = 12x Sprayer 600ml
Special offercomplete packing unit quick-cleaner for brake and clutch parts
CKW free
content: 12x sprayer with volume of 600 ml
quick-cleaner for brake and clutch parts
content: 200 ml
excellent solvency for mixture of grease, oil and dirt
protection against creeping current
Disposable syringe 10ml
Prod.No.
Disposable syringe with working volume of 10ml
fit to suck away of different fluids or to measure out (for instance epoxy resin and curing agent)
Disposable syringe 20ml
Prod.No.
7055
0,95
Disposable syringe with working volume of 20ml
fit to suck away of different fluids or to measure out (for instance epoxy resin and curing agent)
Seite 160 from178
elring seal repair kit
Prod.No.
6218
19,63
Prod.No.
6254
7,50
set of different seal plates to customized seals himself
graval and underbody protection, black, spray 500ml
based on rubber-synthetic resin
color: black
recoatable
Liquid surface seal *elring AFD 2000* 50g
Prod.No. 6950
19,97
Anarobic surface seal AFD 2000 made by elring Germany
Solvent-free sealing compund. Ideal for sealing metal haousings, bearing covers, flanges, etc. without
a solid seal
Temperature stability: -50°C up to +150°C
Fills gabs as small as 0.3mm
Instant sealing effect
Separates again easily
Resistant to water, coolants, synthetic oils, lubricants, organic solvents.
Threadlocking - Low Strength, Loctite® 222, 10 ml
Prod.No. 6379
Recommended for low-strength threadlocking of adjusting screws, countersunk head screws and set screws.
12,34
Specifications:
Size of Thread: up to M 36
Strength: Low
Functional Strength (typical value @ 22 °C): 6 hrs
Breakaway Torque M10 bolts: 6 Nm
Long-Term Temperature Resistance: +150°C
Threadlocking - Maximum Strength, Loctite® 2701, 10ml
Prod.No.
6380
12,34
Loctite® 2701 - Maximum Strength (improved Loctite® 270)
For use on all metal fasteners (including stainless steels and those with protective coatings such as zinc) where
regular removal for maintenance is not required. Recommended for permanently locking studs on engine blocks
and pump housings.
Specifications
Size of Thread: Up to M 20
Strength: High
Seite 161 from178
Threadlocking - Medium Strength, Loctite® 243, 10ml
Prod.No.
6381
14,76
Loctite® 243 - Medium Strength - Oil Tolerant
Effective on all types of metal threaded fasteners. Prevents loosening on vibrating parts such as pumps, motor
mounting bolts, gear boxes or presses. Recommended for use where disassembly with hand tools is required for
servicing and where parts are contaminated with oil.
Specifications:
Size of Thread: Up to M 36
Strength: Medium
universal housing seal, demountable, tube 75g
Prod.No. 6258
- easy demountable, not hardending housing seal
- remains plastically over the hole area of temperature in vehicles
- resistant against diesel fuel, oils and lubrication materials, water and mixture of water and glycol
universal.housing seal, demountable, tube 200g
9,66
Prod.No.
6257
17,92
Prod.No.
6203
0,75
Prod.No.
6219
39,33
Prod.No.
6220
59,88
- easy demountable, not hardending housing seal
- remains plastically over the hole area of temperature in vehicles
workshop requirement > hose clips
Hose clip, 1-ear
13,2 - 15,8 mm
for fuel hose with outside diameter from D=13,2mm up to 15,8mm.
the wide of the clip is 8,2mm.
start-diameter: 16,5mm
only one time to use
workshop requirement > tools
2-claw-puller 100 mm
spanning width: 100 mm
spanning depth: 100 mm
3-claw-puller 100 mm
spanning width: 100 mm
spanning depth: 100 mm
32-parts screwdriver bit-set
Prod.No. 6717
21,95
Screwdriver bit-set with thirty screwdriver bits, one locator for screwdriver bits and one 3/8"-tetrahedral
bit in a plastic box with girdle clip
screwdriver bits for screws with follow head-types are included:
Phillips-tip (size 1, 2 (2x), 3)
Pozidrive-tip (size 1, 2 (2x),3)
slotted-head (3mm, 4mm, 5mm, 6mm)
hexagon socket (3mm, 4mm, 5mm, 6mm)
Torx (T10, T15, T20, T25, T27, T30, T40)
Torx with pin (T10, T15, T20, T25, T27, T30, T40)
Seite 162 from178
Adapter M14 ignition ajustment
Prod.No.
6818
28,99
Prod.No.
6819
28,99
Prod.No.
6310
61,76
Prod.No.
6778
14,92
Prod.No.
6409
15,00
Prod.No.
8-pieces open-end spanner - combination wrench with different spanner gaps.
Spanner angular 15°, box wrench 15° bent off.
6863
89,97
adapter for the dial gauge to adjust the ignition point.
Fit to the spark plug tap M14. Hexagon nut for mounting SW 22.
usefull for the fallowing vehicles:
made in Germany
material: brass
Trabant 601
Wartburg 353
Barkas B1000
Adapter M18 ignition ajustment
adapter for the dial gauge to adjust the ignition point.
Fit to the spark plug tap M18. Hexagon nut for mounting SW 22.
usefull for the fallowing vehicles:
made in Germany
material: brass
Trabant 500,600,601
Wartburg 311
Framo
IFA F8 / F9
P70
bending tool for brake pipe
high-quality tool from HAZET
special for plastic coated brake pipes with diamter of 4,75 mm (our Art.No.: 662 und 663)
combination wrench HAZET, 17mm
High quality tool made by HAZET
wrench opening: 17mm
material: chromium-vanadium steel
box wrench 15° bent off
combination wrench with ratchet
wrench opening: 10mm
Combination wrench-set XL Gedore
scope of delivery: wrench opening: 8,9,10,11,13,14,17,19
wo 8: length: 170mm
wo 9: length: 180mm
wo 10: length: 190mm
material: 31CrV3
surface: chromed
made by Gedore Germany
Seite 163 from178
Cutting disk 125 x 0,8 for angle grinder
Prod.No.
1317
3,55
Prod.No.
1318
30,45
Prod.No.
1319
2,92
Prod.No.
7301
43,59
Prod.No.
6821
49,09
ultra-thin cutting disk fit for One hand- angle grinder
only 0,8 mm thin
inner diameter of mounting hole: 22,2 mm
free of iron and sulphur, usable also for stainless steel
particularly applicative for thin sheet metall (fast cutting with thin slit)
up to 12.200 rpms
one piece
cutting disk 125 x 0,8 for angle grinder (set of 10 pieces)
ultra-thin cutting disk fit for One hand angle grinder
only 0,8 mm thin
particularly applicative for thin sheet metall (fast cutting with thin slit)
up to 12.200 rpms
ten pieces
cutting disk 125 x 1,0 for angle grinder
thin cutting disk fit for One hand angle grinder
thickness: 1,0 mm
inner diameter of mounting hole: 22 mm
particularly applicative for thin sheet metall
up to 12.000 rpms
one piece
Dial gauge digitale type
Good quality dial indicator for example to adujst the ignition timing.
case diameter: 58mm
tolerance: 0,01mm
effective range: 0-10mm
made in China
scope of delivery without seperate extension pin
non shock proof
Dial gauge shock proof
High quality dial indicator for example to adujst the ignition timing.
case diameter: 58mm
tolerance: 0,01mm
made in Germany
shock proof
Seite 164 from178
Dial gauge simple type
Prod.No.
6820
33,44
Prod.No.
7300
14,99
Prod.No.
7473
69,77
Prod.No.
7470
72,55
High quality dial indicator for example to adujst the ignition timing.
case diameter: 58mm
tolerance: 0,01mm
made in Germany
non shock proof
Dial gauge simple type
Cheap dial indicator for example to adujst the ignition timing.
case diameter: 58mm
tolerance: 0,01mm
made in China
non shock proof
Dies set 15 parts
Complete kit with dies to tap metrical thread.
Best use for handmade.
Scope of delivery:
1 pieces of dies M3
1x twist drill for M3
1 pieces of dies M4
1 pieces of dies M5
1 pieces of dies M6
1 pieces of dies M8
1 pieces of dies M10
1x tap wrench
Dies set 29 parts
Complete kit with dies to tap metrical thread.
Best use for handmade.
Scope of delivery:
3 pieces of dies M3
3 pieces of dies M4
3 pieces of dies M5
1 pieces of dies M6
3 pieces of dies M8
Seite 165 from178
Extensions pin for Dial gauge, 60mm
Prod.No.
7302
3,09
Prod.No.
6864
319,00
Prod.No.
6793
11,77
Prod.No.
6312
34,52
Prod.No.
6313
53,20
Extension for dial gauge. Fit to all offered gauges
thread: M2,5
diameter: 4mm
tolerance: 0,01mm
made in China
non shock proof
Impact wrench Hitachi WR16SA
Electrical impact screwdriver with right/left rotary.
Solid professional model with additional holding lever.
Strongest at this level: torque 360Nm
supply voltage 220V~
tetrahedral 1/2 inch
Knot wheel brush, 115 x 22,2 for angle grinder
Knot wheel brush fit for One hand angle grinder
brushes made of steel wire
for preparation of welding seams and cleaning
up to 12.500 rpms
one piece
lever grease gun
german industry quality
pre-installed with reinforced hose and hydraulical connector
match grease cartridge: Art.No.: 6311
lubrication set
lubrication set consist of:
lever grease gun, Art.No.: 6312
grease cartridge, Art.No.: 6311
adhesive transparent lubricant, Art.No.: 6255
plate shears with leverage effect, IDEAL, right
Prod.No. 6095
IDEAL-plate shears for straight cuttings with leverage effect to reduce the needed hand strength.
19,94
right side cutting
light version for thickness of plate up to 1,2 mm (sheet steel) or 1,0 mm (stainless steel sheet)
cutting unit made of die-forged stainless steel
cutting edges inductive hardened and with little teeth
with spring to open itself
puller for ball joint 18/38mm
Prod.No.
6192
38,80
gable width: 18 mm
max. lenght of ball joint axle: 38 mm
best use for track rod joints of Trabant and Wartburg.
Seite 166 from178
Prod.No.
6193
49,85
Prod.No.
6814
68,18
Prod.No.
6779
199,50
Prod.No.
6738
9,90
gable width: 23 mm
gable width: 29 mm
fit to pull up the lever of steering gear
Set of locking pliers, 11-piece
eleven-piece set of locking pliers with workshop board
Very good suited for spot-welding with MIG-welding equipment
3x with long nose
4x with curved jaws and wire-cutter
2x with curved jaws
2x with straight jaws
Spot weld driller, 6 mm
Special HSS-twist drill for car body making
Stable construction for hard drill jobs with hand drill. Especially fit to drill out spot welds and to drill
thin-walled work pieces. Extremely high precision drill of steel sheet, brass sheet, aluminium sheet,
zinc plate, sheet copper and plastic plates.
diameter: 6 mm
length: 66 mm
special cut with pike
surface: sheer
dextrorotatory
Spot weld driller, 8 mm
Prod.No.
6737
11,91
Special HSS-twist drill for car body making
Stable construction for hard drill jobs with hand drill. Especially fit to drill out spot welds and to drill
thin-walled work pieces. Extremely high precision drill of steel sheet, brass sheet, aluminium sheet,
zinc plate, sheet copper and plastic plates.
diameter: 8 mm
length: 80 mm
special cut with pike
surface: sheer
dextrorotatory
Tin-solder 35%, 250g
Prod.No.
6742
8,71
Tin-solder stick
weight: about 250g
tin content: 35%
DIN 1707: L-PbSn35Sb
Solidus temperature: 186°C
Liquidus temperature: 235°C
Seite 167 from178
Prod.No.
6743
11,79
Prod.No.
6744
17,37
Prod.No.
6739
16,60
Tin-solder stick
weight: about 250g
tin content: 40%
DIN 1707: L-PbSn40Sb
Tin-solder stick
weight: about 250g
tin content: 60%
DIN 1707: L-Sn60Pb
Tinning paste, 250g
Ready for use, easy to spread paste to prepare soft-soldering of body sheet.
Remains of flux are water soluble and should given a wash thoroughly after tinning (before adding the
tin-solder).
content: 250g
tin content: 40%
DIN 8511 F-SW 12/EN 29454
Tinning paste, 250g
Prod.No.
6740
6,60
Ready for use, easy to spread paste to prepare soft-soldering of body sheet.
Remains of flux are water soluble and should given a wash thoroughly after tinning (before adding the
tin-solder).
content: 250g
tin content: 40%
DIN 8511 F-SW 12/EN 29454
workshop requirement > Lubricants
adhesive transparent lubricant, spray 400ml
Prod.No.
6255
14,66
Prod.No.
6349
18,79
good adhesion
excellent corrosion protection
good water resistance
content: 400ml
high performance grease with molybdenum, tin 1kg
high load carrying capacity
low oxidation, suitable for longterm lubrication
resistant to water wash-out
good corrosion protection
protection against fretting corrosion
Seite 168 from178
high performance grease with molybdenum, tube 100g
Prod.No.
6256
5,20
Prod.No.
7087
6,95
Prod.No.
6311
3,99
high load carrying capacity
low oxidation, suitable for longterm lubrication
resistant to water wash-out
good corrosion protection
protection against fretting corrosion
High temperatur adhesive lubricant, spray 400ml
adhesive lubricant with ceramic, free of metal
suited to screw joint inside light alloy to prevent against galvanic corrosion
good adhesion
temperature resistance: -30°C (-22°F) up to +1450°C (+2642°F)
excellent corrosion protection
good water resistance
capacitiy: 400ml
multi-purpose grease, cartridge 400g
multi-purpose grease for use with a lever grease gun
usable in temperature range: -30°C up to +120°C
For lubrication of ball- and slide bearings with normal up to high revs.
Also usable in dusty and soggy operation conditions.
(for instance: wheel bearings, brake cables, steering gears and bushes)
silicone cleaner spray, 500ml
Prod.No. 6309
4,90
special solvent and means of degreasing
content: 500 ml
silicone cleaner spray for fast remove of silicone oils und greases without any remnants (also for removing our
silicone spray, Art.No.: 6300)
98% sheer active agent
silicone spray, 300ml
Prod.No.
6300
4,88
Prod.No.
6669
17,94
Prod.No.
6670
37,89
indoor- and outdoor-spray
lubricates but don´t greases
antistatic
workshop requirement > fuel tank coating
FeDOX concentrated rust remover, 1000ml
FERTAN, 1000ml
Seite 169 from178
fuel stabiliser, 250ml
Prod.No.
6671
10,89
for trouble free over-wintering of engines and fuel tanks.
The volume of the boddle protect 50 liter petrol.
TAPOX 2-part fuel tank coating
Prod.No. 6491
36,29
Fuel resistant 2-component epoxy resinvarnish fit to inner coating of fuel tanks und also as high-quality
rust protection paint.
Depending on shape of fuel tank sufficent for tank volume from 16 to 40 litre.content:
TAPOX (component 1) 415g
TX-10 hardener (component 2) 125g
detailed description of workmanship for tank coating inclusive all preliminaries
workshop requirement > Mounting parts
External teeth lock washer M8
Prod.No. 6679
Lock washer Schnorr with teeth can be used for bolt connection with hight tightening torques. Properly for bolts M8
0,10
surface zinc coated
inside diameter: 8,4 mm
outside diameter: 13 mm
thickness: 1 mm
made in Germany
External teeth lock washer S10
Prod.No. 6681
0,12
Lock washer Schnorr with teeth can be used for bolt connection with hight tightening torques. Properly
for bolts M10
surface zinc coated
inside diameter: 10,4 mm
thickness: 1 mm
made in Germany
Hexagon nut M10
Prod.No.
6686
0,40
strength class: 8.8
tap: M10
highness: 9,3 mm
surface: galvaniced
made in Germany
workshop requirement > Mounting parts > Bolts metrical
Seite 170 from178
Hexagon bolt M12 x 1,5 x 35mm
Prod.No. 7611
2,14
Hihg grade bolt with metrical thread.
Ideal use for Old and Youngtimer to clamp dynamic load components like chassis, brakes, axles,
steering and so on..
thread: M12 x 1,5mm
length total: 43 mm
bolt length: 35mm
without barrel
spanner gap: SW19
surface: galvaniced
made in Germany
Prod.No. 7468
2,14
tap: M12 x 1,5mm
length total: 48 mm
bolt length: 40mm
length of the barrel: 15mm
spanner gap: SW19
surface: galvaniced
made in Germany
Prod.No. 7471
2,58
tap: M12 x 1,5mm
length total: 67 mm
bolt length: 60mm
spanner gap: SW19
surface: galvaniced
made in Germany
Prod.No. 7472
2,87
tap: M12 x 1,5mm
length total: 78 mm
bolt length: 70mm
spanner gap: SW19
surface: galvaniced
made in Germany
Seite 171 from178
Prod.No. 7469
3,06
tap: M12 x 1,5mm
length total: 88 mm
bolt length: 80mm
spanner gap: SW19
surface: galvaniced
made in Germany
Prod.No. 7684
4,23
tap: M14 x 1,5mm
length total: 70 mm
bolt length: 60mm
spanner gap: SW22
surface: galvaniced
made in Germany
Prod.No. 7474
Ideal use for Old and Youngtimer to clamp dynamic load components like chassis, brakes, axles, steering and so on..
4,27
tap: M14 x 1,5mm
length total: 78 mm
bolt length: 70mm
spanner gap: SW22
surface: galvaniced
made in Germany
Prod.No. 7683
4,85
tap: M14 x 1,5mm
length total: 90 mm
bolt length: 80mm
spanner gap: SW22
surface: galvaniced
made in Germany
Seite 172 from178
Prod.No. 7685
4,23
tap: M16 x 1,5mm
length total: 60 mm
bolt length: 50mm
spanner gap: SW24
surface: galvaniced
made in Germany
Prod.No. 7686
5,92
tap: M16 x 1,5mm
length total: 90 mm
bolt length: 80mm
spanner gap: SW24
surface: galvaniced
made in Germany
Hexagon head screw M10 x 25 mm
Prod.No.
6683
0,40
Prod.No.
6682
0,33
Prod.No.
6684
0,35
strength class: 8.8
tap: M10
length: 25 mm
surface: galvaniced
made in Germany
strength class: 8.8
tap: M8
length: 10 mm
surface: galvaniced
made in Germany
strength class: 8.8
tap: M8
length: 25 mm
surface: galvaniced
made in Germany
workshop requirement > Accessory
Seite 173 from178
Grease nipple 1/4 -28 inch
Prod.No.
7574
0,34
Prod.No.
7575
0,49
Prod.No.
7582
0,48
Prod.No.
7561
0,34
Prod.No.
7580
0,39
Prod.No.
7562
0,43
Conical nipple type A, standard
Version: H 1 1/4? -28
Ball grease nipple for using at many Old- and Youngtimers.
Thread: american low climp.
thread: 1/4? -28
spanner cap: SW7
Grease nipple A10
Version: H 1 M 10x1
Thread: M10 self sealed (conical)
thread: M10x1
spanner cap: SW11
Grease nipple A10, self forming thread
Conical nipple type A, DIN 71412
Version: H 1 M 10x1
Thread: M10 self forming
thread: M10x1
spanner cap: SW11
Grease nipple A6
Version: H 1 M 6x1
thread: M6x1
spanner cap: SW7
Version: H 1 M 6x1
thread: M6x1
spanner cap: SW7
Grease nipple A8
Version: H 1 M 8x1
thread: M8x1
spanner cap: SW9
Seite 174 from178
Prod.No.
7581
0,49
Prod.No.
7583
0,87
Prod.No.
7577
0,99
Prod.No.
7576
0,49
Prod.No.
6861
1,91
Prod.No. 6860
Protection glasses for autogenic welding method.
Ring nut system with rubber hose cover, elastic band and plan glasses diamether D=50mm.
protection class DIN A5
7,93
Version: H 1 M 8x1
thread: M8x1
spanner cap: SW9
Grease nipple B6 (45°)
Conical nipple type B, standard, connection 45 degrees inclined.
Version: H 2 M 6x1
thread: M6x1
spanner cap: SW7
Grease nipple R 1/4 inch
Version: H 1 R 1/4?
Thread: 1/4 inch self sealed (conical)
thread: 1/4?
spanner cap: SW14
Grease nipple R 1/8 inch
Version: H 1 R 1/8?
Thread: 1/8 inch self sealed (conical)
thread: 1/8?
spanner cap: SW11
workshop requirement > Protection equipment
Laminated class round
Protection glass insert fit to manny glasses with diamether D=50mm.
Welding glasses Robusta 310
care products
Seite 175 from178
deer sebum rubber care pen
Prod.No.
6259
3,84
Prod.No.
6420
4,35
for care and protection of rubber parts in cars, caravan and inside of house
protects against frost and weathering
disabled the freezing together of car door with rubber seal
silicone free
natural product
ELSTERGLANZ universal polish paste, 150ml
ELSTERGLANZ is the legendary universal polish paste from East Germany
The translation for name ELSTERGLANZ is magpie brilliance.
Elsterglanz cleans, polishes and preserves by means of a protective film all metall materials like
copper, brass, tin, nickel, silver, gold and unsurpassable stainless-steel.
Recommend to care all of our polished articles, for instance our Design-dorrhandles-pair for Trabant
601 und 1.1 or polished fuel tank plug.
ELSTERGLANZ universal polish paste, 150ml
Prod.No.
6664
4,35
ELSTERGLANZ Chrome-care with orange oil
The translation for name ELSTERGLANZ is magpie brilliance.
Elsterglanz chrome-care cleans, polishes and preserves reliably chrome surfaces.
Particularly good for hard chrome-plated surfaces of car- or motorbike parts.
big tube with 150ml
Chrome-care is free of acid and because of using natural ingredients sparing to the material. The
special ingredients act cleaning and particularly grease dissolving and leavs a protective film.
SONAX Chrome- & Alupaste 75ml
Prod.No. 6325
4,96
Gently and effectively removes rust and tarnished areas from chrome, aluminium and all non-ferrous
metals. Restores the original shine and preserves by means of a protective film which prevents the
build up of new rust.
Recommend to care all of our polished articles, for instance our Design-dorrhandles-pair for Trabant
601 und 1.1 or polished fuel tank plug.
SONAX motor cleaner 400ml
Prod.No.
7414
10,47
cleaner for motor, car body and repair parts
for oily dust
quick and thoroug
producer: Henkel AG&Co
contens: 400ml
made in Germany
Seite 176 from178
SONAX motor cleaner 500ml
Prod.No.
6194
9,66
Prod.No.
6195
8,87
Prod.No.
ADDINOL SEMI SYNTH SAE 10W-40
for Trabant 1.1, Wartburg 1.3 and most other motors from VAG-combine (Audi, VW, Seat, Skoda)
particulate with synthetic oil
no sheer minerally oil
contens: 1 Litre
6248
7,33
cleaner for motor, car body and repair parts
for oily dust
quick and thoroug
spray bottle
producer: Sonax
contens: 500ml
made in Germany
SONAX motor plast 300ml
protective coating for motor
protection against corrosion and current leak
oils
ADDINOL 4 stroke motor oil SAE 10W-40, 1 litre
Prod.No. 6250
contens: 20 Litre
Prod.No. 6249
contens: 4 Litre
87,03
23,84
ADDINOL FLUSHING OIL SUPER, 0,5l
Prod.No. 6889
11,00
ADDINOL FLUSHING OIL SUPER
The perfect inside cleaner for engines of Trabant 1.1, Wartburg 1.3 and most other 4-stroke engines
contens: 0,5 Litre (sufficent for appr. 5 L engine oil filling)
proper flushing guarantees complete removal of used oil and maximum cleanliness of the engine
dissolves sludge and solids
Power Conditioner increasing the engine output
Seite 177 from178
ADDINOL SUPER DRIVE, Motorenöl 15W-40, 20L
Prod.No.
6731
85,80
High-end multi-purpose engine oil with classification SAE 15W-40
made in Germany by ADDINOL
Engine oils for any gasoline and diesel engines of passenger cars, in particular for modern injection
and injection and turbo engines (z.B. 1.9 TDI in Sharan AFN and many more)
Quantity: 20 Liter
Specification and approvals:
ACEA A3/B3; API SL/CF; MB 229.1; VW 501 01/505 00
Seite 178 from178

Bildkatalog des Onlineshops LDM

Transcription

Similar documents

compact wheel loaders

ordering instructions mail order

Parts List Power Lock™ Series

68-73 Datsun 510 Rear Disc Brake Conversion

ARGENTINA`S INFLATION TOPS 300%

At Metropolitan Mercedes Benz, We Know You Want The Best For

Information material for Van-Mark brakes

2014 valkyrie - Honda Powersports

Forum Presentation

menox hand controls - Eco Medical Accessibility Department