PermaTorque Head Gaskets PermaTorque MLS

PermaTorque Head Gaskets PermaTorque MLS

PermaTorque Head Gaskets
Oil Pan Gaskets
Gaskets have a wire ring combustion seal inside the stainless steel
armor for highly concentrated sealing. The wire ring squeezes the combustion seal between the head and the block three times greater than
standard head gaskets. Gaskets are sold individually.
Part No.
Nom.
Gasket Comp. Comp.
Bore Thick. Volume
Application
SB Chevy 1955-97 262, 265, 267, 283, 302, 307, 327, 350, 400
Iron/Aluminum Head Apps.,
FEL1003*
4.166" .041"
Except Aluminum Blocks, 4.155" Max.
FEL1004*
Iron/Aluminum Head Apps.
4.190" .041"
FEL1010* Alum. Head Apps. Only, 4.155" Max. Bore 4.166" .039"
FEL1014
Iron/Aluminum Head Apps.
4.200" .039"
FEL1034*
Iron/Aluminum Head Apps.
4.200" .041"
Iron/Aluminum Head Apps.,
FEL1036*
4.250" .051"
Extra Thick, Extra Large Bore
FEL1044
Iron/Alum. Head Apps., Extra Thick
4.200" .051"
FEL1045† Iron/Alum. Head Apps., Severe Duty Apps. 4.180" .039"
Iron/Alum. Head Apps.,
FEL1094*
4.100" .015"
Except 400, Extra Thin
* Gasket does not have steam holes for 400 street operation.
† Requires a precision receiver groove machined in cylinder head.
9.1cc
9.2cc
8.9cc
9.0cc
9.3cc
11.9cc
11.2cc
9.0cc
3.2cc
Application
Nom.
Comp.
Comp. Thick. Volume
SB Chevy 1955-97 262, 265, 267, 283, 302, 307, 327, 350, 400
FEL1142 Iron/Alum. Head Apps. Inc. 400 4.100"
.040"
FEL1143 Iron/Alum. Head Apps. Inc. 400 4.165"
.040"
FEL1144 Iron/Alum. Head Apps. Inc. 400 4.200"
.040"
9.0cc
9.2cc
9.3cc
Part No.
Valve Cover Gaskets
Application
Material
Thk.
SB Chevy 1955-97 262, 265, 267, 283, 302, 307, 327, 350, 400
FEL1602 Most Cylinder Heads
Fel-CoPrene Rubber
5/32"
FEL1603 Most Cylinder Heads
Blue Stripe Cork-Rubber
7/32"
All Except
Cork-Lam Cork-Rubber/Steel
FEL1604
5/16"
1955-56 Engines
Core
1959-86, Chevy
Silicone Molded
FEL1628
1/4"
18°/Brodix -12
Rubber/Steel Core
Splayed Valve
FEL1641
Composite-Silicone/Steel Core 3/32"
GM Corporate
FEL1644 Chevy 18°/Brodix -12 Composite-Silicone/Steel Core 3/32"
1986-97
Cork-Lam
FEL1648
1/4"
Late Model Center Bolt
Cork-Rubber/Steel Core
Cork-Lam
FEL1649 Chevy 18°/Brodix -12
1/4"
Cork-Rubber/Steel Core
Silicone Molded
FEL1655-1 SB2, SB2.2 Mirror Port
11/64"
Rubber/Steel Core
SB Chevy
Water Pump To Block Gaskets FEL5152
Quick Change Gasket FEL2303
1/32" steel core gasket fits most 10-bolt cover
quick changes.
Thk.
3/32"
3/32"
3/32"
3/32"
3/32"
3/32"
9/64"
9/64"
9/64"
9/64"
9/64"
Description
SB Chevy 1955-97 262, 265, 267, 283, 302, 307, 327, 350, 400
FEL2900 ............1959-85, 2-Pc. Silicone
FEL2909 ............Special Large O.D. for “Rocket” Block or Align Honed 400,
2-Pc. Fluoroelastomer.
FEL2912 ............1959-85, 2-Pc. Fluoroelastomer, High Vacuum
FEL2919 ............1986-95, 1-Pc. Premium Material
Intake Manifold Gaskets
Fel-Pro intake manifold gaskets are
available for a variety of engines and
are sold in sets, however, many are also available in bulk (10 sets).
Order bulk by adding a “B” to the end of the part number. Bulk gaskets
are sold without end seals and distributor gaskets.
Part No.
Part No.
Material
Rear main seals in silicone, Teflon or fluoroelastomer.
High vacuum seals are used with crankcase vacuum pumps.
Multi-Layer Steel (MLS) head gaskets
withstand the greater combustion chamber
pressures of high output engines. Full-hard
stainless steel construction withstands
“scrubbing” between the head and block. Strategically placed sealing
beads eliminate leak paths, and an extra strong “stopper” layer provides exceptional primary combustion sealing. Selected gaskets listed
may also be available in other bore sizes and thicknesses. All gaskets
are sold individually.
Part No.
Application
Rear Main Seals
PermaTorque MLS Head Gaskets
Gasket
Bore
Part No.
SB Chevy 1955-97 262, 265, 267, 283, 302, 307, 327, 350, 400
FEL1802
1957-74
Thin Front Seal, LH Dipstick
FEL1803
1975-79
Thick Front Seal, LH Dipstick
FEL1818
1980-85
Thick Front Seal, RH Dipstick
Side Rails
FEL1821
Thin/Thick Seals, LH Dipstick
Trimmed For Strokers
FEL1823
CNC Bow Tie Block
Composite/Steel Core/Silicone
“Rocket”/Dart Iron
Rubber-Coated
FEL1839
Eagle/GM Med. Deck
Fiber/Steel Core
1975-79, Side Rails
FEL1880
Thick Front Seal, LH Dipstick
Trimmed For Strokers
1980-85, Side Rails
FEL1881
Thick Front Seal, RH Dipstick
Trimmed For Strokers
Side Rails Trimmed
Thick Ft. Seal,
FEL1882
For Strokers
Straight Side Rails
1957-74
FEL1885
Thin Front Seal, LH Dipstick
1-Piece With Rigid Carrier
1986-97,
Thick Front Seal,
FEL1886
Bowtie Short Deck Block
1-Pc. Rear Seal
Application
Material
Construction
Port Size
Thk.
SB Chevy 1955-97 262, 265, 267, 283, 302, 307, 327, 350, 400
Stock Or Small
FEL1205
Std. Printoseal 1.28" x 2.09"
Race Port
FEL1205S-3 Stock/Small Race Port
Steel Core
1.28" x 2.09"
FEL1206
Medium Race Port
Std. Printoseal 1.31" x 2.21"
FEL1206S-3
Medium Race Port
Steel Core
1.31" x 2.21"
FEL1207
Large Race Port
Std. Printoseal 1.38" x 2.28"
Trim To Fit
FEL1244
Std. Printoseal 1.25" x 1.90"
(Largest Port Size Listed)
Trim To Fit
FEL1245
Std. W/Coating 1.25" x 1.90"
(Largest Port Size Listed)
Raised Runner Pontiac/
FEL1263
Std. W/Coating 1.31" x 2.02"
Chevy “867” Head
FEL1266
Medium Race Port
Std. W/Coating 1.31" x 2.21"
FEL1267
Large Race Port
Std. W/Coating 1.38" x 2.28"
Raised Runner Pontiac/
FEL1286
Std. W/Coating 1.31" x 2.02"
Chevy “867” Head
.060"
.065"
.060"
.065"
.060"
.060"
.120"
.060"
.120"
.120"
.120"
Exhaust Header Gaskets
Fel Pro’s exhaust header gaskets
have a durable perforated steel core for
exceptional sealing without blowouts.
Part No.
Application
Port Size
Small Block Chevy 1955-97 262, 265, 267, 283, 302, 305, 307, 327, 350, 400
FEL1405
Square (Large Race)
1.55" x 1.55"
FEL1406
“D” Shape (Brodix Track 1)
1.53" x 1.63"
FEL1407
Round (Hooker/Stahl Adapter Plate)
1.81" Dia.
FEL1408
Round (Hooker Lg. Tube Header Adapter)
2.19" Dia.
FEL1409
Round (Brodix Spread Port) 18°
1.81" Dia.
FEL1426
Round
1.59" Dia.
FEL1445
Raised “D” Port (Brodix -12B/2000)
1.78" x 1.70"
FEL1482
18° Pro Action
1.74" x 1.60"
113
6000 Series Competition Valves
Competition Plus Valves
Valves work well with high valve spring pressures and roller
cams for reliable performance at an affordable price. After a
two step forging process, the EV8 stainless steel intake and
exhaust valves are heat-treated and stress-relieved. Small
block Chevy valves have hard-chromed stems, swirl polished
heads and friction-welded tips. Sold in sets of eight unless
specified. For a single valve replace -8 with a -1.
Aerospace alloys, including EV8-Z18, provide high tensile
strength while a two step forging process maintains proper
grain flow and correct material structure. Small block Chevy
valves listed are heat treated and stress relieved. Each valve
design undergoes flow bench testing to determine optimum
flow and velocity. Sold in sets of eight. To order a single
valve, replace the -8 with a -1.
Part No.
Type
Small Block Chevy
FERF6107-8 Exh.
FERF6144-8
Exh.
Head
Size
Stem
Overall
Diameter Length
1.500" 11/32" 4.960"
1.500" 11/32" 5.010"
FERF6100-8
Exh.
1.600" 11/32" 4.960"
FERF6108-8
Exh.
1.600" 11/32" 4.960"
FERF6104-8
Exh.
1.600" 11/32" 5.010"
FERF6145-8
Exh.
1.600" 11/32" 5.010"
FERF6202-8
Exh.
1.600" 11/32" 5.060"
FERF6147-8
Exh.
1.600" 11/32" 5.160"
FERF6102-8
Int.
1.940" 11/32" 4.960"
FERF6142-8
Int.
1.940" 11/32" 5.010"
FERF6101-8
Int.
2.020" 11/32" 4.960"
FERF6103-8
Int.
2.020" 11/32" 5.010"
FERF6208-8
Int.
2.020" 11/32" 5.060"
FERF6206-8
Int.
2.020" 11/32" 5.160"
FERF6105-8
Int.
2.055" 11/32" 4.960"
FERF6114-8
Int.
2.055" 11/32" 5.010"
FERF6207-8
FERF6115-8
Int.
Int.
2.055" 11/32" 5.060"
2.080" 11/32" 4.960"
FERF6116-8
Int.
2.080" 11/32" 5.010"
FERF6203-8
Int.
2.080" 11/32" 5.060"
FERF6164-1
Int.
2.080" 11/32" 5.160"
Competition Plus
Hollow Stem Valves
Description
12° Flo, Stock/+.050"
12° Super Flo,
+.050"/+.100"
12° Super Flo
Stock/+.050"
12° Flo. Stk./+.050"
12° Super Flo
+.050"/+.100"
12° Flo +.050"/+.100"
20° Semi Tulip
Super Flo +.100"
12° Super Flo
Brodix/+.200"
12° Super Flo,
Stock/+.050"
12° Super Flo,
+.050"/+.100"
12° Super Flo Stk./+.050"
12° Super Flo
+.050"/+.100"
12° Super Flo +.100"
12° Super Flo/Canfield
+.200"
12° Super Flo Stk./+.050"
12° Super Flo
+.050"/+.100"
12° Super Flo +.100"
12° Super Flo Stk./+.050"
12° Super Flo
+.050"/+.100"
12° Super Flo +.100"
12° Super Flo/
Canfield/+.200"
Cutaway Artist
Rendering
Part No.
Type
Head
Size
Stem
Overall
Diameter Length
Description
Small Block Chevy
FERF1100PQ-8 Exh. 1.600" 11/32" 4.960" 14° Super Flo, Stock/+.050"
14° Super Flo,
FERF1102PQ-8 Exh. 1.600" 11/32" 5.010"
+.050"/+.100"
FERF1148PQ-8 Exh. 1.600" 11/32" 5.060"
14° Super Flo, +.100"
FERF1187P-8 Exh. 1.600" 11/32" 5.060" 19° Tulip Super Flo, +.100"
14° Super Flo, Bro./Pont.,
FERF1140PQ-8 Exh. 1.600" 11/32" 5.160"
+.200"
FERF1476P-8 Exh. 1.600" 11/32" 4.960" 12° Super Flo, Stock/+.050"
24° Flo/Ultra Light/Radial
FERF2212P-8 Exh. 1.600" 7mm 5.010"
Groove
FERF1108P-8 Exh. 1.625" 11/32" 5.060" 20° Tulip Super Flo, +.100"
14° Super Flo,
FERF1128PQ-8 Exh. 1.625" 11/32" 5.160"
Bro./Pont., +.200"
14° Super Flo/Dart/Brodix
FERF1257P-8 Exh. 1.625" 11/32" 5.560"
18°/+.600"
FERF1115P-8 Int. 2.020" 11/32" 4.960" 12° Super Flo, Stock/+.050"
12° Super Flo,
FERF1112P-8 Int. 2.055" 11/32" 5.010"
+.050"/+.100"
FERF2252P-8 Int. 2.055" 11/32" 5.060"
14° Super Flo, +.100"
12° Super Flo,
FERF1114P-8 Int. 2.080" 11/32" 5.010"
+.050"/+.100"
FERF1147P-8 Int. 2.080" 11/32" 5.060"
12° Super Flo, +.100"
12° Super Flo,
FERF1139P-8 Int. 2.080" 11/32" 5.160"
Bro./Pont., +.200"
Competition Cylinder Head Gasket
FERG50021
Competition small
block Chevy gasket
relies upon a perforated steel plate for
flexibility and strength.
A hi-temp non-metallic
compound coats the plate, while a stainless steel plate seals the
combustion chambers. Gasket has a 4.065" bore and is .035" thick.
Sold individually.
Hollow stem small block Chevy valves are 20% lighter
than solid stem valves, which translates into increased
engine RPM. Valves are the result of a unique manufacturing process where stems are gun-drilled and
micro-finished. Friction welded tips, radial grooves,
chrome plated stems and super flow, undercut stems are
standard. Sold in sets of eight. For a single valve replace
-8 with a -1.
Part No.
Type
Head
Stem
Overall
Size Diameter Length
Description
Small Block Chevy
FERF1024P-8
Exh. 1.600" 11/32"
4.960"
FERF1001P-8
Int.
5.160"
2.080" 11/32"
14° Super Flo/Radial
Groove/+.050"
12° Super Flo/Radial
Groove/+.250"
Frankland Racing Rear Ends
SPECIAL ORDER ONLY
Call for options and more information.
114
The Light FLAFR1001
The Light from Flaming River uses 2 D-cell batteries to eliminate cumbersome battery leads. Convenient, single
wire inductive pickup and brilliant Xenon bulb allow precise timing, even in direct sunlight. Lens area is surrounded
by an impact-absorbing, flexible rubber guard.
Fluid Transfer Systems
Pump Supply Systems
A safe, quick and effective method of
pumping or drawing gasoline, alcohol or oil
at a rate of five gallons per minute. Transfer
liquids from utility jugs, fuel tanks, cells,
etc. Fluid transfer systems are offered
in 10 or 15 gallon versions. Specify blue,
clear or red utility jug when ordering.
Transfer fuel, oil, etc. quickly, safely and effectively from utility jugs or large drums. Pump supply
systems are offered to transfer liquids from 5 or 7.5
gallon utility jugs, or 55 gallon drums.
Part No.
Part No.
Description
FLF20210 ..........10 Gallon System, Includes Pump System (FLF30301),
(2) White 5 Gallon Utility Jugs And Heavy Duty, 200 lb. Capacity Cart
With Telescoping Handle (FLF60602).
FLF20216R........15 Gallon System, Includes Pump System (FLF30301), (2) Red 7.5
Gallon Utility Jugs (FLF75001) And Fold-Up, 200 lb. Capacity Cart With
Telescoping Handle (FLF60602).
Replacement Components
FLF60602 ..........Fold-Up 200 lb. Capacity Cart
FLF75001 ..........7.5 Gallon Utility Jug, Red
Economy High Strength Rod Ends
Economical, two-piece CMX/CMXL rod ends have hard
chrome plated 52100 steel ball and heat treated alloy
steel bodies. (Available with a PTFE liner. Add a “T” to
the end of the part number.)
RH
Part No.
LH
Part No.
Thread
Size
Hole
Size
Ult. Static
Radial Load
FKBCMX8
FKBCMX10-8
FKBCMXL8
FKBCMXL10-8
1/2"-20
5/8"-18
.500"
.500"
17,000
18,000
Description
FLF30301 ..........Pump Supply System, Fits 5 Or 7.5 Gallon Jugs
FLF30304-1 ......Pump Supply System, Fits 5 Or 7.5 Gallon Utility Jugs
And 55 Gallon Drums
System Accessories
FLF40402 ..........5' Hose Extension Kit, Allows Transferring Liquids
From Large Tanks
FLF40405 ..........Drum Extractor Kit, Adapts Pump Supply System (FLF30301)
To 55 Gallon Drum
FLF80803 ..........Draw Tube Extension, Adapts Pump Supply System
To 15 Gallon Utility Jug
Extra Strength Heavy Duty
Shank Rod Ends
RSM/RSML three-piece rod ends have extra strength,
heavy duty shanks with low carbon steel, chromate
treated bodies, hard chrome plated steel balls and heat
treated steel alloy races. RSMX/RSMXL rod ends have
heat treated alloy steel bodies.
RH
Part No.
LH
Part No.
FKBRSM8 FKBRSML8
FKBRSMX8 FKBRSMXL8
Thread
Size
Hole
Size
Ult. Static
Radial Load
5/8"-18
5/8"-18
.500"
.500
12,843
31,420
Precision Series Rod Ends
JMX/JMXL three-piece rod ends are made of high
strength alloy with 52100 hard chrome plated steel
balls, heat treated steel alloy bodies and races. (Rod
ends are also available with a PTFE liner. Add a “T” to
the end of the part number.)
Steel And Aluminum
Jam Nuts
RH
Part No.
LH
Part No.
Thread
Size
Hole
Size
Ult. Static
Radial Load
Thread
Size
Hex
Size
Steel
RH
Steel
LH
Aluminum
RH
Aluminum
LH
FKBJMX6
FKBJMX7
FKBJMX8
FKBJMXL6
FKBJMXL7
FKBJMXL8
3/8"-24
7/16"-20
1/2"-20
.375"
.437"
.500"
9,550
10,290
16,242
5/16"-24
3/8"-24
7/16"-20
1/2"-20
5/8"-18
1/2"
9/16"
11/16"
3/4"
15/16"
FKBSJNR05
FKBSJNR06
FKBSJNR07
FKBSJNR08
FKBSJNR10
FKBSJNL05
FKBSJNL06
FKBSJNL07
FKBSJNL08
FKBSJNL10
FKBAJNR05
FKBAJNR06
FKBAJNR07
FKBAJNR08
FKBAJNR10
FKBAJNL05
FKBAJNL06
FKBAJNL07
FKBAJNL08
FKBAJNL10
115
Series 8000 Push-Lite Race Hose Ends
Series 2000 Pro-Flow Hose Ends
Manufactured from lightweight aluminum with an attractive black
anodized finish, Push-Lite race hose ends feature a barbed end that
combines ease of assembly and a leakproof seal.
Pro-Flow hose ends utilize a “single nipple”, which allows the socket
to draw the hose over a long tapered single nipple, effectively sealing
the hose between the inside of the socket and the outside of the nipple.
Hose ends are easily re-used due to the fact that there is no sliver of
cut hose to remove before installing the fitting on a new length of hose.
Fittings have a black anodized finish.
Part No.
Straight
FRG200104-BL
FRG200106-BL
FRG200108-BL
FRG200110-BL
FRG200112-BL
FRG200116-BL
30°
FRG203006-BL
FRG203008-BL
FRG203010-BL
FRG203012-BL
FRG203016-BL
45°
FRG204504-BL
FRG204506-BL
FRG204508-BL
FRG204510-BL
FRG204512-BL
FRG204516-BL
60°
FRG206006-BL
FRG206008-BL
FRG206010-BL
FRG206012-BL
FRG206016-BL
90°
FRG209004-BL
FRG209006-BL
FRG209008-BL
FRG209010-BL
FRG209012-BL
FRG209016-BL
120°
FRG212006-BL
FRG212008-BL
FRG212010-BL
FRG212012-BL
FRG212016-BL
150°
FRG215006-BL
FRG215008-BL
FRG215010-BL
FRG215012-BL
FRG215016-BL
180°
FRG218006-BL
FRG218008-BL
FRG218010-BL
FRG218012-BL
FRG218016-BL
Hose Size
-4
-6
-8
-10
-12
-16
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-6
-8
-10
-12
-16
-6
-8
-10
-12
-16
-6
-8
-10
-12
-16
Gauge Adapters
Part No.
Description
FRG495005-BL......... -6 Male x -6 Female, Inline,
1/8" Female NPT On Side
FRG495020-BL......... -3 x 1/8" Female NPT Straight
116
Part No.
Straight
FRG220104-BL
FRG220106-BL
FRG220108-BL
FRG220110-BL
FRG220112-BL
FRG220116-BL
30°
FRG223004-BL
FRG223006-BL
FRG223008-BL
FRG223010-BL
FRG223012-BL
FRG223016-BL
45°
FRG224504-BL
FRG224506-BL
FRG224508-BL
FRG224510-BL
FRG224512-BL
FRG224516-BL
60°
FRG226004-BL
FRG226006-BL
FRG226008-BL
FRG226010-BL
FRG226012-BL
FRG226016-BL
90°
FRG229004-BL
FRG229006-BL
FRG229008-BL
FRG229010-BL
FRG229012-BL
FRG229016-BL
120°
FRG231204-BL
FRG231206-BL
FRG231208-BL
FRG231210-BL
FRG231212-BL
FRG231216-BL
150°
FRG231504-BL
FRG231506-BL
FRG231508-BL
FRG231510-BL
FRG231512-BL
FRG231516-BL
180°
FRG231804-BL
FRG231806-BL
FRG231808-BL
FRG231810-BL
FRG231812-BL
FRG231816-BL
Hose Size
-4
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-4
-6
-8
-10
-12
-16
-3 Bulkhead Tee On-The-Run
FRG480403-BL
Aluminum Tube Sleeve
Part No.
AN Size
-3 x 45° Bulkhead
FRG483703-BL
FRG481903-BL......... -3
FRG481904-BL......... -4
FRG481906-BL......... -6
FRG481908-BL......... -8
FRG481910-BL......... -10
90° Bulkhead
90° Union
Part No.
Part No.
AN Size
FRG483303-BL......... -3
FRG483304-BL......... -4
FRG483306-BL......... -6
FRG483308-BL......... -8
FRG483310-BL......... -10
FRG483312-BL......... -12
FRG483316-BL......... -16
Bulkhead Tee On-The-Side
Part No.
AN Size
FRG483403-BL......... -3
FRG483404-BL......... -4
FRG483406-BL......... -6
FRG483408-BL......... -8
FRG483410-BL......... -10
FRG483412-BL......... -12
Aluminum Tee Pipe On-The-Side
Part No.
Part No.
AN Size
FRG483203-BL......... -3
FRG483204-BL......... -4
FRG483206-BL......... -6
FRG483208-BL......... -8
FRG483210-BL......... -10
FRG483212-BL......... -12
FRG483216-BL......... -16
FRG483220-BL......... -20
Bulkhead Nut
Part No.
AN Size
FRG492403-BL......... -3
FRG492404-BL......... -4
FRG492406-BL......... -6
FRG492408-BL......... -8
FRG492410-BL......... -10
FRG492412-BL......... -12
FRG492416-BL......... -16
FRG492420-BL......... -20
Tee Female Swivel On Side
Part No.
AN Size
FRG480603-BL......... -3AN
FRG480604-BL......... -4AN
FRG480606-BL......... -6AN
FRG480608-BL......... -8AN
FRG480610-BL......... -10AN
FRG480612-BL......... -12AN
FRG480616-BL......... -16AN
FRG480620-BL......... -20AN
Aluminum Tube Nut
Part No.
AN Size
FRG481803-BL......... -3
FRG481804-BL......... -4
FRG481806-BL......... -6
FRG481808-BL......... -8
FRG481810-BL......... -10
Description
FRG498201-BL......... -3 Tee With Female Swivel
FRG498202-BL......... -4 Tee With Female Swivel
FRG498203-BL......... -6 Tee With Female Swivel
FRG498204-BL......... -8 Tee With Female Swivel
Tee
Part No.
AN Size
FRG482403-BL......... -3
FRG482404-BL......... -4
FRG482406-BL......... -6
FRG482408-BL......... -8
FRG482410-BL......... -10
FRG482412-BL......... -12
FRG482416-BL......... -16
1/8" FPT Female Pipe Coupler
FRG491001-BL
Male Pipe Nipple
Part No.
Aluminum Flare Plug
Description
FRG482503-BL......... -3 x 1/8" MPT
FRG482603-BL......... -3 x 1/8" MPT
Part No.
Straight Bulkhead
Description
FRG482103-BL......... -3 x 90°
FRG482104-BL......... -4 x 90°
FRG482106-BL......... -6 x 90°
FRG482108-BL......... -8 x 90°
FRG482110-BL......... -10 x 90°
FRG482112-BL......... -12 x 90°
FRG482116-BL......... -16 x 90°
NPT Size
FRG491101-BL......... 1/8" MPT
FRG491102-BL......... 1/4" MPT
FRG491103-BL......... 3/8" MPT
FRG491104-BL......... 1/2" MPT
FRG491106-BL......... 3/4" MPT
Pipe Reducer
Part No.
NPT Size
FRG491201-BL......... 1/8" x 1/4"
FRG491202-BL......... 1/4" x 3/8"
FRG491203-BL......... 1/8" x 3/8"
FRG491204-BL......... 3/8" x 1/2"
FRG491205-BL......... 1/4" x 1/2"
FRG491206-BL......... 1/8" x 1/2"
FRG491207-BL......... 1/2" x 3/4"
FRG491208-BL......... 3/8" x 3/4"
FRG491209-BL......... 1/4" x 3/4"
117
Aluminum Male Reducers
Part No.
Radius Fittings
Comes with “O” ring.
AN Size
FRG491902-BL......... -3 x -4
FRG491906-BL......... -4 x -6
FRG491912-BL......... -6 x -8
FRG491913-BL......... -10 x -4
FRG491914-BL......... -6 x -10
FRG491915-BL......... -8 x -10
FRG491916-BL......... -12 x -4
FRG491918-BL......... -12 x -6
FRG491919-BL......... -12 x -8
FRG491920-BL......... -10 x -12
FRG491922-BL......... -10 x -16
FRG491923-BL......... -12 x -16
Part No.
Union
Part No.
AN Size
FRG481503-BL......... -3 x -3
FRG481504-BL......... -4 x -4
FRG481506-BL......... -6 x -6
FRG481508-BL......... -8 x -8
FRG481510-BL......... -10 x -10
FRG481512-BL....... -12 x -12
FRG481516-BL....... -16 x -16
Aluminum Flare Cap
Part No.
AN Size
Female Swivels
FRG492903-BL......... -3
FRG492904-BL......... -4
FRG492906-BL......... -6
FRG492908-BL......... -8
FRG492910-BL......... -10
FRG492912-BL......... -12
FRG492916-BL......... -16
Part No.
-16 x 45° Female - Female Coupler
FRG496216-BL
NPT Size
FRG493201-BL......... 1/16" MPT
FRG493202-BL......... 1/8" MPT
FRG493203-BL......... 1/4" MPT
FRG493204-BL......... 3/8" MPT
FRG493205-BL......... 1/2" MPT
FRG493206-BL......... 3/4" MPT
Swivel Reducer
Part No.
NPT Size
FRG493301-BL......... 1/8" MPT
FRG493302-BL......... 1/4" MPT
FRG493303-BL......... 3/8" MPT
FRG493304-BL......... 1/2" MPT
FRG493306-BL......... 3/4" MPT
Gauge Adapters
Part No.
Swivel Flare Expander
Description
FRG495000-BL......... -4 Male x -4 Male, Inline,
1/8" FPT On The Side
FRG495001-BL......... -6 Male x -6 Male, Inline,
1/8" FPT On The Side
FRG495002-BL......... -6 Male x 3/8" MPT, Inline,
1/8" FPT On The Side
FRG495021-BL......... -4 x 1/8" FPT Straight
FRG495022-BL......... -3 x 1/8" FPT-90°
FRG495023-BL......... -4 x 1/8" FPT-90°
Part No.
FRG495001-BL
FRG495002-BL
118
AN Size
FRG497204-BL......... -4 Female x -3 Male
FRG497206-BL......... -6 Female x -4 Male
FRG497208-BL......... -8 Female x -6 Male
FRG497210-BL......... -10 Female x -6 Male
FRG497211-BL......... -10 Female x -8 Male
FRG497212-BL......... -12 Female x -8 Male
FRG497213-BL......... -12 Female x -10 Male
FRG497216-BL......... -16 Female x -10 Male
FRG497217-BL......... -16 Female x -12 Male
FRG497218-BL......... -8 Female x -4 Male
Hex Pipe Plug
Part No.
AN Size
FRG496103-BL......... -3
FRG496104-BL......... -4
FRG496106-BL......... -6
FRG496107-BL......... -6 x -8
FRG496108-BL......... -8
FRG496109-BL......... -8 x -10
Internal Allen Pipe Plug
Part No.
Description
FRG495100-BL......... -6AN x 9/16"-18 (6)
FRG495101-BL......... -6AN x 3/4"-16 (8)
FRG495102-BL......... -8AN x 9/16"-18 (6)
FRG495103-BL......... -8AN x 3/4"-16 (8)
FRG495104-BL......... -8AN x 7/8"-14 (10)
FRG495105-BL......... -10AN x 3/4"-16 (8)
FRG495106-BL......... -10AN x 7/8"-14 (10)
FRG495107-BL......... -10AN x 1-1/16"-12 (12)
FRG495108-BL......... -12AN x 7/8-14" (10)
FRG495109-BL......... -12AN x 1-1/16"-12 (12)
FRG495110-BL......... -4AN x 9/16-18" (6)
FRG495111-BL......... -4AN x 3/4-16" (8)
FRG495112-BL......... -4AN x 7/8-14" (10)
FRG495113-BL......... -6AN x 7/8-14" (10)
FRG495114-BL......... -6AN x 1-1/16"-12 (12)
FRG495115-BL......... -8AN x 1-1/16"-12 (12)
FRG495116-BL......... -8AN x 1-5/16"-12 (16)
FRG495117-BL......... -10AN x 1-5/16"-12 (16)
FRG495118-BL......... -12AN x 1-5/16"-12 (16)
FRG495119-BL......... -16AN x 1-5/16"-12 (16)
FRG495120-BL......... -16AN x 1-1/16"-12 (12)
FRG495122-BL......... -12AN x 3/4-16" (8)
FRG495123-BL......... -20AN x 1-5/16"-12 (16)
FRG495124-BL......... -4AN x 3/8"-24 (3)
FRG495125-BL......... -4AN x 7/16"-20 (4)
AN Size
FRG497304-BL......... -3 Female x -4 Male
FRG497306-BL......... -4 Female x -6 Male
FRG497308-BL......... -6 Female x -8 Male
FRG497310-BL......... -8 Female x -10 Male
FRG497312-BL......... -10 Female x -12 Male
FRG497320-BL......... -16 Female x -20 Male
90° Swivel To Male Pipe Black
Part No.
FRG499103-BL......... -3AN x 1/8" NPT
FRG499104-BL......... -4AN x 1/8" NPT
FRG499144-BL......... -4AN x 1/4" NPT
FRG499106-BL......... -6AN x 1/4" NPT, Black
FRG499162-BL......... -6AN x 1/8" NPT
FRG499166-BL......... -6AN x 3/8" NPT
FRG499168-BL......... -6AN x 1/2" NPT
FRG499107-BL......... -8AN x 1/4" NPT
FRG499108-BL......... -8AN x 3/8" NPT
FRG499188-BL......... -8AN x 1/2" NPT, Black
FRG499110-BL......... -10AN x 1/2" NPT, Black
FRG499111-BL......... -10AN x 3/8" NPT, Black
FRG499112-BL......... -12AN x 3/4" NPT, Black
FRG499113-BL......... -12AN x 1/2" NPT, Black
Weld Bungs With 1.0" Dia. Step
Part No.
Aluminum AN To NPT Adapters
Description
Description
FRG499558 .............. -8 Male (3/4"-16)
FRG499560 .............. -10 Male (7/8"-14)
FRG499562 .............. -12 Male (1-1/16"-12)
FRG499562
Premium Black Nylon Race Hose
Ideal for racing applications, nylon race hose incorporates
a synthetic rubber core that has an operational range of
-40° F. to +300° F. and up to 500 PSI of working pressure, allowing for use with most oils, coolants and fuels.
Lightweight, durable and attractivebraided nylon hose is
reinforced with a single braid of bright corrosion resistant
type 302 stainless steel wire braid for added strength. Hose
is designed for use with FPS Series 2000 hose ends and
FPS Sport-Crimp hose ends.
Note: This hose is not intended for use with 3000 Series hose
ends.
AN
Size
Hose
I.D.
3 Ft.
Roll
10 Ft.
Roll
20 Ft.
Roll
-4
-6
-8
-10
-12
-16
7/32"
11/32"
7/16"
9/16"
11/16"
7/8"
FRG840304
FRG840306
FRG840308
FRG840310
FRG840312
FRG840316
FRG841004
FRG841006
FRG841008
FRG841010
FRG841012
FRG841016
FRG842004
FRG842006
FRG842008
FRG842010
FRG842012
FRG842016
Ford Type FRAHP1
GM Type FRAHP4
Fram high performance oil filters have an anti-drainback valve, and a relief valve which acts as an internal
bypass, opening when inlet pressure is greater than
outlet pressure. The HP1 Filter’s valve opens at a 9-12
PSI differential; the HP4’s relief valve opens at 15-22
PSI. Dimensions: 3-5/8" O.D. x 5-1/2" Ht.
Micron Rating ...............................................25 Nominal
Recommended Max. Oper. Press. .................200 PSI
Recommended Max. Flow Rate ...................10 GPM-Outside To Center
Relief Valve Setting .......................................HP1/9-12 PSI, HP4/15-22 PSI
Min. Hydrostatic Burst Pressure...................HP1/500 PSI, HP4/325 PSI
Thread Size ...................................................HP1/3/4"-16, HP4/13/16"-16
Hose
Size
NPT
Size
Straight
Part No.
45°
Part No.
90°
Part No.
-3
-4
-4
-4
-6
-6
-6
-6
-8
-8
-8
-10
-10
-10
-12
-12
-16
-16
1/8"
1/8"
1/4"
3/8"
1/8"
1/4"
3/8"
1/2"
1/4"
3/8"
1/2"
3/4"
1/2"
3/8"
3/4"
1/2"
3/4"
1"
FRG481603-BL
FRG481604-BL
FRG481605-BL
FRG481644-BL
FRG481662-BL
FRG481606-BL
FRG481666-BL
FRG481668-BL
FRG481607-BL
FRG481608-BL
FRG481688-BL
FRG481609-BL
FRG481610-BL
FRG481611-BL
FRG481612-BL
FRG481613-BL
FRG481615-BL
FRG481616-BL
FRG482303-BL
FRG482304-BL
FRG482344-BL
–
FRG482362-BL
FRG482306-BL
FRG482366-BL
FRG482368-BL
FRG482307-BL
FRG482308-BL
FRG482388-BL
–
FRG482310-BL
FRG482311-BL
FRG482312-BL
FRG482313-BL
–
FRG482316-BL
FRG482203-BL
FRG482204-BL
FRG482244-BL
–
FRG482262-BL
FRG482206-BL
FRG482266-BL
FRG482268-BL
FRG482207-BL
FRG482208-BL
FRG482288-BL
FRG482209-BL
FRG482210-BL
FRG482211-BL
FRG482212-BL
FRG482213-BL
FRG482215-BL
FRG482216-BL
Hose Pressure Test Kit FRG900060
Handy kit allows the quick testing of AN hose assemblies. A compressed air source and water bath to submerge assemblies is all that
is needed to check for leaks. Kit includes individual line testers for -3
through -16. Individual line testers may also be purchased separately.
Individual Line Testers
Part No.
Hose Size
FRG900663 .......-3
FRG900664 .......-4
FRG900666 .......-6
FRG900668 .......-8
FRG900670 .......-10
FRG900672 .......-12
FRG900676 .......-16
37° Flaring Tool FRG900500
Economical flaring tool allows forming an
AN specification 37° JIC flare to 3/16" through 5/8"
diameter hard line tubing.
2 Quart Capacity FRAHP6A
No relief valve or anti-drainback valve. Used with the
Fram HPK6, HPK600 adapter kits for racing applications. 4-5/8" O.D. 6-11/16" Ht.
Micron Rating ................................................................ 15 Nominal
Recommended Max. Oper. Press. ................................. 200 PSI
Recommended Max. Flow Rate ................................... 20 GPM
Outside To Center Min. Hydrostatic Burst Press.......... 400 PS
Straight Thread Size...................................................... 1-1/2"-12
Mini Sprint R6 Oil Filter
Part No.
Description
FRAPH6017A............ R6 Oil Filter
119
Outlaw Sprint
Tail Tanks
Sprint Tail Tank Hardware
Tank for winged sprint
cars holds up to 33 gallons and locates over
200 lbs. of fuel 4" farther
forward than conventional
tanks. Molded inserts
facilitate side mounting
and a step on the lower
section places weight
on rear torsion tubes to
clear brake rotors and rear end vents. Includes a top pickup and -12AN
fittings. Bottom pickup and Ultra-lite Outlaw tanks are available by
special order.
Description
Standard 28 Gallon
Outlaw Tail Tank
28 Gallon
Outlaw Tail With Baffle
30 Gallon
Dominator Tail Tank
33 Gallon
Outlaw Tail With Baffle
Bladder
Part No.
Tail Tank
Part No.
Complete Assy.
Part No.
FUESB128DT
FUEST128-TP
FUESB228DT
–
FUEST128-TP
FUESB228DT-B
FUEST130
FUESB230AT
–
FUEST333
FUEITVV10AFK
Hardware is designed for use with the new Dominator tail tank assembly.
Part No.
Description
FUEITVV06LP-S ........ -6 Low Profile Check Valve
FUEITVV10LP-S ........ -10 Low Profile In-Tank Check Valve Assembly
FUEITVV10AFK ......... -10 Vent Valve Air Filter
FUEBHF12KN ........... -12 Bulkhead Inlet Fitting Kit
Fill Plate With Flush Cap
And Cover Plates
Part No.
FUESB333DT-B
FUEBHF12KN
FUEITVV10LP-S
Description
FUESFP240 .............. Standard 4" x 6" Fill Plate
FUECP7X12
FUE1GAS98 .............. Fill Plate Gasket
FUECP6X10 .............. Cover Plate With Nuts Inserts, 6" x 10"
FUECP7X12 .............. Cover Plate With Nuts Inserts, 7" x 12" NEW
Other tanks and bladders are available. Please call for more information.
G-Force Helmets
A complete line of revolutionary, lightweight helmets that incorporate mounting points for the Hans®
Device and, unless otherwise noted, meet Snell SA2010 and SFI 31.2A (open face) or 31.2A (full face)
specs. See the size chart below for proper helmet selection.
Pro Eliminator And Pro Eliminator X
Sleek Pro Eliminator and Pro Eliminator X lightweight Z38 composite
shells with G-Flow ventilation let cool air in and hot air out through
the top and back. Hypoallergenic CoolTec liner contributes to overall
driver comfort. The Pro Eliminator is available in white or black; the
Pro Eliminator X is available in black with flamed graphics only. Meets
SA2010 specs.
Small
Medium
Large
X-Large
XX-Large
Small
Medium
Large
X-Large
XX-Large
Measurement
Size
Metric
20-1/2"
20-7/8"
21-1/4"
21-5/8"
22"
22-3/8"
22-3/4"
23-1/8"
23-1/2"
23-7/8"
24-1/4"
24-3/4"
25-1/8"
6-1/2 (XX-Small)
6-5/8 (X-Small)
6-3/4 (X-Small)
6-7/8 (Small)
7 (Small)
7-1/8 (Medium)
7-1/4 (Medium)
7-3/8 (Large)
7-1/2 (Large)
7-5/8 (X-Large)
7-3/4 (X-Large)
7-7/8 (XX-Large)
8 (XX-Large)
52
53
54
55
56
57
58
59
60
61
62
63
64
Pro Eliminator X
Pro Eliminator
Size
Helmet Size Conversion Chart
White
Part No.
Pro Eliminator
GFR3023SMLWH
GFR3023MEDWH
GFR3023LRGWH
GFR3023XLGWH
GFR3023XXLWH
Pro Eliminator X
–
–
–
–
–
Black
Part No.
GFR3023SMLBK
GFR3023MEDBK
GFR3023LRGBK
GFR3023XLGBK
GFR3023XXLBK
GFR3025SMLBK
GFR3025MEDBK
GFR3025LRGBK
GFR3025XLGBK
GFR3025XXLBK
Ryan Kirkendall
120
Photo By: Tom Willavize
GF505
One-Piece Racing Suits
G5 Racing Gloves
Lightweight, flexible gloves are sewn from quality Nomex and leather. Gloves include reinforced
leather palms and knuckle pads, adjustable Velcro
wrist closures and meet SFI 3.3/5 specifications.
Available in black, blue or red.
The GF505 triple-layer racing suit’s Pyrovatex shell
and exclusive Coolquilt liner provide breathable comfort. A second, fire retardant fabric liner wicks moisture
away from the body. Suits have white billboards and
are trimmed with contrasting piping, white arm and
leg stripes, large pockets, brass zippers with Nomex
tape, Nomex cuffs and Nomex neck enclosures for extra
protection. Suits meet SFI 3.2A/5 specifications and are
available in black, red or blue.
Color
Small
Medium
Large
X-Large
XX-Large
Black GFR4380SBK GFR4380MBK GFR4380LBK GFR4380XBK GFR4380XXLBK
Red GFR4380SRD GFR4380MRD GFR4380LRD GFR4380XRD
–
Blue GFR4380SBL GFR4380MBL GFR4380LBL GFR4380XBL
–
GF525
One-Piece Racing Suits
Multi-layer racing suit’s
Pyrovatex fabric provides a
TPP (Thermal Protective
Performance) rating of
21 to meet SFI 3.2A/5
specifications. The
attractive, bright semigloss finish and straight
black epaulets cover an
inner layer that wicks
moisture and breathes for
added comfort. The SFI tag
is on the left arm cuff for
easy tech inspection.
Choose among black, red or blue.
Color
Medium
Large
X-Large
Black
Red
Blue
GFR4525MBK
GFR4525MRD
GFR4525MBL
GFR4525LBK
GFR4525LRD
GFR4525LBL
XX-Large
GFR4525XBK GFR4525XXBK
GFR4525XRD GFR4525XXRD
GFR4525XBL GFR4525XXBL
Color
Small
Medium
Large
X-Large
Black
Blue
Red
GFR4101SBK
GFR4101SBL
GFR4101SRD
GFR4101MBK
GFR4101MBL
GFR4101MRD
GFR4101LBK
GFR4101LBL
GFR4101LRD
GFR4101XBK
GFR4101XBL
GFR4101XRD
GF235 RaceGrip
Mid-Top Racing Shoes
High quality suede leather racing shoe has an exclusive rubber
RaceGrip sole for exceptional
pedal feel. The CoolTec liner and
RaceGrip inner sole and arch support deliver extra comfort. Offered in
black, blue or red in sizes 5-13.
Size
Black
Part No.
Blue
Part No.
Red
Part No.
5
6
7
8
9
10
11
12
13
GFR0235BK5
GFR0235BK6
GFR0235BK7
GFR0235BK8
GFR0235BK9
GFR0235BK10
GFR0235BK11
GFR0235BK12
GFR0235BK13
GFR0235BL5
GFR0235BL6
GFR0235BL7
GFR0235BL8
GFR0235BL9
GFR0235BL10
GFR0235BL11
GFR0235BL12
GFR0235BL13
–
GFR0235RD6
GFR0235RD7
GFR0235RD8
GFR0235RD9
GFR0235RD10
GFR0235RD11
GFR0235RD12
GFR0235RD13
Flame-Retardant
Underwear
Flame-retardant underwear is the
essential foundation of any racing
uniform. Tops and bottoms are available in
natural color.
Color
Small
Medium
Large
X-Large
Tops
36-38
38-42
42-46
46-49
Natural
GFR4160SNT GFR4160MNT GFR4160LNT GFR4160XNT
Bottoms
29-32
32-35
38-40
41-43
Natural
GFR4161SNT GFR4161MNT GFR4161LNT GFR4161XNT
Note: It is highly recommended that a layer of underwear be worn with all
suits for added protection, particularly when using a single layer suit.
GF545
One-Piece Racing Suits
Double layer, GF545 racing
suit’s GTEX outer layer and
Nomex knit inner layer combine
for a soft knit feel and cool
interior. The 360°, soft knit arm
gussets and 360° armholes
offer greater range of motion,
and contrasting box stitching
accents appearance and adds
durability. Suit meets stringent
SFI 3.2A/5 specifications and
has a TPP (Thermal Protective
Performance) rating of 23.
Choose from suits in black, red
or blue.
Flame-Retardant Socks
Color
Medium
Large
X-Large
Black
Red
Blue
GFR4545MBK
GFR4545MRD
GFR4545MBL
GFR4545LBK
GFR4545LRD
GFR4545LBL
GFR4545XBK
GFR4545XRD
GFR4545XBL
Description
Small
Medium
Size
Nomex Socks
3-5
GFR4140SCT
5-7
GFR4140MCT
Large
X-Large
7-9
10-13
GFR4140LCT GFR4140XCT
121
Helmet Bag GFRGF-1002
Adult And Junior
Latch And Link Harnesses
Durable fleece lined nylon bag will keep
helmet looking new and scratch-free.
Offered in black only.
Harnesses are constructed from lowstretch, PolyTek comfort-coated webbing and
combined with 3" bolt-end hardware, rather
than the traditional 2". Double adjustable
belts adjust at the normal points and at the
mounting points to fit virtually any application. Sets include 3" lap and shoulder belts,
and 1.75" submarine belt. Harnesses meet
stringent SFI 16.1 specifications, and are
offered in black, blue or red.
Helmet Skirts
Soft knit fire-retardant skirts have an
extra wide Velcro strap for fastening.
Black
Part No.
Red
Part No.
Description
Blue
Part No.
Black
Part No.
Blue
Part No.
Individual Shoulder Harness Sets
5-Pt., Pull-Down
GFR6000BK
GFR6000BL
5-Pt., Pull-Up
GFR6100BK
GFR6100BL
Individual Shoulder Harness Sets - Junior Racer
5 Pt., Pull-Up
GFR6460BK
–
GFRGF-4240BK GFRGF-4240RD GFRGF-4240BL
Red
Part No.
GFR6000RD
GFR6100RD
–
Camlock Harness
Flame-Retardant
Balaclavas
Provides an extra level of protection to the head and face. Choose
single or double eyeport. In single
or double layer.
Natural
Part No.
Black
Part No.
Single Eyeport/Single Layer
GFR41121L1NT
GFR41121L1BK
Single Eyeport/Double Layer
GFR41122L1NT
GFR41122L1BK
Double Eyeport/Double Layer
GFR41122L2NT
GFR41122L2BK
Blue
Part No.
Red
Part No.
GFR41121L1BU
GFR41121L1RD
GFR41122L1BU
GFR41122L1RD
–
–
Color
Small
Medium
Large
Black
Blue
Red
GFR4122SBK
GFR4122SBL
GFR4122SRD
GFR4122MBK
GFR4122MBL
GFR4122MRD
GFR4122LBK
GFR4122LBL
GFR4122LRD
Red
Part No.
Individual Shoulder Harness Sets
5-Pt. Pull-Down
GFR7000BK
GFR7000BL
GFR7000RD
Note: Camlock harness may also be used as a wrap around installation.
Description
Black
Part No.
Red
Part No.
Blue
Part No.
Harness Pad
GFR4098BK
GFR4098RD
GFR4098BL
Arm Restraints
Helmet Accessories
High strength nylon arm
restraints are covered in
foam and flame-retardant
cloth. Available in black,
blue or red.
GFRGF-8600
Description
GFRGF-8006............. Plastic Tear-Off Posts
GFRGF-8600............. Pivot Kit (ProFit), All New Model Helmets
122
Blue
Part No.
G-Force Harness Pads provide an
extra measure of comfort and safety
for the driver. Covered in flame-retardant fabric with Velcro closures. Sold
in pairs and are available in black,
blue or red.
G-Force 360° Helmet Supports are
made from high density, fire
retardant foam covered with
soft, knit CoolTec material.
Available in black, blue or red,
in small, medium and large
sizes. Meets SFI 3.3 Specs.
Part No.
Black
Part No.
Description
Harness Pads
Helmet Supports
GFRGF-8006
Low-stretch, PolyTek comfortcoated webbing is combined with
3" bolt-in hardware and Camlock
mechanism with an ultra-lightweight
magnesium case. A 1/4 turn will
fasten or release the belts. Offered
in 5-point, individual shoulder harness versions only with pull-down
adjustment and choice of black,
blue or red. Harnesses meet SFI 16.1
specifications.
GFR4087BK
GFR4087JNRBK
Description
Black
Part No.
Red
Part No.
Blue
Part No.
Adult
Junior
GFR4087BK
GFR4087JNRBK
GFR4087RD
–
GFR4087BL
–
Nields Quicksteer By GME
GMEA9467AHS
Power Steering Pump
GMEPAS1400HG
Regardless of steering configuration on
the sprint car, the Nields Quicksteer by
GME will fit thanks to the removable
right hand tube that changes the box from
full length to half length. The adjustable
steering reservoir pivots and slides on
the left steering tube. The Quicksteer can be easily installed.
Includes a spin-on tube
and quick release.
Brand new power steering pump,
designed for Sprints or Midgets, is
fully CNC-machined from billet
7075 aluminum and weighs in at
only 2.65 lbs. Compatible to drive
off of standard or raised cam engines,
pump uses precision ground internal gears
for optimum pressure. Sold complete with
mounting adapter, -10 AN suction and -6 AN pressure fittings.
Components For Nields Quicksteer By GME
Power Steering Fluid
Part No.
GME132X01
GME125-01
GME267X01
GME105X04
GME100A01
Description
GME125-01 .............. 1 Quart
GME125-02 .............. Case of 8 Quarts
Replacement components for the Quicksteer.
Part No.
Description
GME100A01 ............. Adjustable Slide-On Reservoir
GME105X04 ............. Pitman Arm, Angle Broached
GME110A03 ............. Quick Release Push-On
GME132X01 ............. Half Gear Mounting Bracket
GME240-01 .............. Lid For Reservoir
GME267X01 ............. Spin-On Tube for Right Side
Scott Hull
Photo By: Tom Willavize
Steering Wheels
“D” shape, 11-3/4" dia. steering wheels
feature molded, polyurethane grips with a
leather grained finish, 1-3/8" dish design
and are offered with choice of black or silver
anodized spokes.
Performance Series
Aluminum Steering Wheels
Performance Series Wheels are fashioned
from 6061-T6 aluminum and covered with a
thick, textured foam cushion grip for comfort.
Available with or without finger grips.
Description
13" Dia. Steering Wheel
13" Dia.
Steering Wheel With Finger Grips
15" Dia. Steering Wheel
15" Dia.
Steering Wheel With Finger Grips
16-1/2" Dia.
Steering Wheel With Finger Grips
Part No.
1-1/2" Dish
Part No.
3-1/8" Dish
Part No.
GRT650
–
GRT660
–
GRT654
GRT655
GRT664
GRT665
–
GRT667
Description
GRT188 .................... Steering WheelSpokes
GRT688 .................... Steering Wheel, Silver Spokes
GRT188
Greg Wheeler
Photo By: Tom Willavize
123
Aluminum Sprint Car Radiators
Griffin aluminum sprint car radiators cool more effectively than others that are twice as thick. Lightweight radiators
are heli-arc welded to help them withstand even the roughest track conditions. Engineered to fit Maxim, Gambler,
Stealth, J&J, Schnee and many other chassis. Custom radiators for almost any configuration are also available on a
special order basis.
Part No.
Size
Tube Size
GRI325152X
GRI345161X
22" x 19" 2-Row
22" x 20" 1-Row
1.00"
1.25"
Billet Aluminum Filler Neck GRIPN19
Fire Extinguishers
Dry chemical fire extinguishers deliver fire protection in an automotive environment. Rechargeable
steel cylinders are manufactured in the U.S. and have all-metal valves and a 6 year warranty. Choose
red or chrome finishes.
Description
Red
Part No.
Chrome
Part No.
Black
Part No.
1.0 Lb. System, 2B:C Rated
2.5 Lb. System, 1A:10B:C
H3RMX100R
H3RMX250R
H3RMX100C
H3RMX250C
H3RMX100B
H3RMX250B
Fire Extinguishers
HalGuard extinguishers are filled with “clean” agent gas that not only combats fire, but leaves
no residue. Ideal for race car protection, U.S. made units are offered in 1.4, 2.5 and 5 lb. versions.
Choose from red or chrome steel cylinders.
Description
Red
Part No.
Chrome
Part No.
Black
Part No.
1.4 Lb. System, 1B:C Rated
2.5 Lb. System, 2B:C Rated
5 Lb. System, 5B:C Rated
H3RHG100R
H3RHG250R
H3RHG500R
H3RHG100C
H3RHG250C
H3RHG500C
H3RHG100B
H3RHG250B
–
Quick Release Mounting Accessories
Billet aluminum mounts provide quick, easy fire extinguisher access. Choose polished or brushed finish mounts.
Note: Band clamps and mounts must be used together. To order, select the proper diameter band clamp and choice of flat surface
or roll bar mount.
Description
Polished
Part No.
Brushed
Part No.
Band Clamp, 1.0/1.4 Lb. Bottle
Band Clamp, 2.5 Lb. Bottle
Flat Surface Mount
1-5/8" Dia. Roll Bar Mount
1-3/4" Dia. Roll Bar Mount
2" Dia. Roll Bar Mount
2-1/4" Dia. Roll Bar Mount
H3RBB100P
H3RBB250P
H3RBMF01P
H3RBMR01P
H3RBMR02P
H3RBMR03P
H3RBMR04P
H3RBB100B
H3RBB250B
H3RBMF01B
H3RBMR01B
H3RBMR02B
H3RBMR03B
H3RBMR04B
H3RBMR02B
H3RBMF01B
H3RBB250P
Flat Surface Mount
“How To...” Books
From carburetor tuning to complete engine rebuilds, HP has books for the
novice or the seasoned professional. Every book is packed full of photos and
illustrations.
Part No.
Description
HPPHP575................ Sheet Metal Handbook, 144 pgs.
HPPHP709................ Revised Metal Fabricator’s Handbook, 176 pgs.
HPPHP1245.............. Engine Builders Handbook, 192 pgs.
HPPHP1492.............. Racing Engine Builder’s Handbook, 192 pgs.
HPPHP1511.............. Dirt Track Chassis And Suspension, 192 pgs.
HPPHP1523.............. High Performance Fasteners And Plumbing, 176 pgs.
124
HPPHP1245
HPPHP1492
HPPHP1511
Racing Piston Rings
Hastings racing piston ring’s low tension, low friction design provides unsurpassed combustion seating and
exceptional sealing. Sets include plasma moly, high tensile cast iron top rings; reverse twist, taper-faced cast iron
second rings, and choice of standard or low tension Flex-Vent stainless steel oil control rings. Low tension oil
rings make significant increases in horsepower and are for racing only. Sets listed must be file-fitted.
Instructions for file fitting included.
File-Fit Piston Ring Sets
Part No.
Bore
Size
Top
Ring
Second
Ring
Oil
Ring
Oil Ring
Tension
Part No.
Bore
Size
Top
Ring
Second
Ring
Oil
Ring
Oil Ring
Tension
HAS2M5508005
HAS2M5521005
HAS2M5523005
HAS2M5505005
HAS2M5521025
HAS2M5505025
HAS2M5523025
HAS2M5508035
HAS2M5521035
HAS2M5505035
HAS2M5538035
HAS2M5523035
HAS2M5508045
HAS2M5521045
HAS2M5523045
4.000"
4.000"
4.000"
4.000"
4.020"
4.020"
4.020"
4.030"
4.030"
4.030"
4.030"
4.030"
4.040"
4.040"
4.040"
5/64"
1/16"
1/16"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
5/64"
1/16"
1/16"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
3/16"
1/8"
3/16"
3/16"
1/8"
3/16"
3/16"
3/16"
1/8"
3/16"
3.0mm
3/16"
3/16"
1/8"
3/16"
Standard
Standard
Standard
Low
Standard
Low
Standard
Standard
Standard
Low
Standard
Standard
Standard
Standard
Standard
HAS2M5505045
HAS2M5540045
HAS2M5508065
HAS2M5521065
HAS2M5523065
HAS2M5505065
HAS2M5525035
HAS2M5513005
HAS2M5529005
HAS2M5510005
HAS2M5529025
HAS2M5510025
HAS2M5513035
HAS2M5529035
HAS2M5510035
4.040"
4.040"
4.060"
4.060"
4.060"
4.060"
4.080"
4.125"
4.125"
4.125"
4.145"
4.145"
4.155"
4.155"
4.155"
1/16"
1.5mm
5/64"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
1/16"
1.5mm
5/64"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
1/16"
1/16"
5/64"
1/16"
1/16"
3/16"
3.0mm
3/16"
1/8"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
Low
Standard
Standard
Standard
Standard
Low
Standard
Standard
Standard
Low
Standard
Low
Standard
Standard
Low
Hawk Brakes provide fade free, longer lasting performance from start to finish. Ferro-Carbon Semi Metallic Racing Pads are burnished with no
break-in required, run up to 200°F. cooler and provide instant response with no lag. Rotor-friendly pads also have a high coefficient of friction and
low wear rate. Consistent, predictable performance lap after lap. Proven in NASCAR, Indy Car, SCCA, IMSA, DIRT, Hooters Cup and ASA.
HP Plus: Good low temperature performance with much better resistance to brake squeal, dust and rotor damage compared to full racing
compounds. Recommended for dirt street stock and econo-modified
applications.
Black: Excellent stopping force with very little fade. Provides good
pad wear and is rotor friendly. Recommended for all dirt applications
as well as low temperature asphalt.
Blue MT-4: Superior stopping power with no fade. Excellent wear
and braking at high temperatures. Less rotor friendly than the black
compound. For heavy braking asphalt applications.
HT-10: A medium to high torque compound with smooth initial
bite. Excellent apply and release characteristics. Ideal for cars with
extremely high deceleration rates and down force.
DTC-05: Smooth, predictable pads provide lower torque in the low to
mid-temperature range and are ideal for dirt circle track.
DTC-30: Dirt track pad material. Unique driver controllability of
brake torque allowing later and deeper brake use into the corners,
while requiring less pedal effort and shorter pedal engagement times.
Excellent release characteristics and requires no heat up or extensive
bedding (break-in period)
DTC-70: For asphalt applications, extremely high torque with aggressive controllable initial bite. Superior release and torque control
characteristics. Brake pads designed for cars with high deceleration
rates with or without down force.
Application
HP Plus Pads
Black Pads
Blue MT-4 Pads
HT-10 Pads
DTC-05 Pads
DTC-30 Pads
DTC-70 Pads
Wilwood Superlite
Wilwood Dynalite
Wilwood DL Bridgebolt
Wilwood DL Single
Wilwood SL Bridgebolt
Sierra Single
HAWHB101N800
HAWHB100N480
HAWHB237N625
HAWHB104N485
–
HAWHB104N485
HAWHB101M800
HAWHB100M480
HAWHB237M625
HAWHB104M485
HAWHB521M800
HAWHB104M485
HAWHB101L800
HAWHB100L480
HAWHB237L625
HAWHB104L485
HAWHB521L800
HAWHB104L485
HAWHB101S800
HAWHB100S480
HAWHB237S625
HAWHB104S485
–
HAWHB104S485
HAWHB101H800
HAWHB100H480
HAWHB237H625
HAWHB104H485
–
HAWHB104H485
HAWHB101W800
HAWHB100W480
HAWHB237W625
HAWHB104W485
HAWHB521W800
HAWHB104W485
HAWHB101U800
HAWHB100U480
HAWHB237U625
–
HAWHB521U800
–
DTC Brake Rotors
Engineered specifically for use with Hawk DTC (Dynamic Torque Control) brake pads, new rotors use an advanced
design and improved metallurgy to deliver the perfect “matched set” for improved braking and longer pad life. Rotors
are RMS finished and feature exclusive, multi-pass progressive slots for increased bite and release, while debris
removal characteristics are also improved. Rotors are offered in straight and directional vane versions.
Part No.
Dia.
Width
Bolt Circle
Hole Size
Slots
Vanes
HAWHR8003R
11.75"
.810"
8 x 7.00"
5/16"
Yes
30 Directional
125
Top Wings
MSD Box Mount HRP8360
Hepfner Racing Products is a
leader in the design and manufacturing of sprint car wings.
CNC punched and formed, each
wing is identical and all internal
components are formed and lightened. Made from .020" 6061 aluminum
with 4130 plated steel internal posts.
.050" thick aluminum Mount is drilled
to accept an MSD Ignition control and has
quick fastener flanges.
Part No.
HRPFLT0510-S
Two-Gauge Mount HRP8361
Description
HRPFLT0510-S ......... Top Wing, Flat Super Side Boards With Recessed Rivets
HRPFLT0510............. Top Wing, Flat With Recessed Rivets
UPS
HRPFLT0510-K ......... Top Wing, Flat With Recessed Rivets, In Kit Form, Able
Comes in a Tube, UPS Able
HRPNDP0512-B ....... Top Wing, 2-1/2" Dished, Non-Recessed Rivets
UPS
HRPVFT0512-K ........ Top Wing, 2-1/2" Dished, Non-Recessed Rivets, Able
Kit Form, UPS Able
HRP8811-P .............. Top Wing Posts, 2 Pcs.
“Super” nose wing is tall and angled with
a 1" dish for increased downforce. Exclusive
recessed rivet design means greater strength,
improved aerodynamics, quicker mud removal and easier
vinyl application. CNC punched and formed, each wing is
identical.
Rock Screen HRP8069
Black powder coated, mandrel bent
steel screen attaches to the roll cage of most chassis and adds protection for driver.
Tubular, telescoping rear wing trees
support the rear of the top wing and
reduce wind resistance on Eagle or
Maxim chassis with HRP top wings.
Front Bumper
With Upper Tube HRP8076-B
Description
HRP8080 ...........Tubular 4130 Steel Rear Wing Tree
HRP8082 ...........Aerodynamic Rear Wing Tree
Constructed from durable stainless steel,
bumper includes upper tube for improved
front end protection.
HRP8165-RH
Nose Wing Mounts
HRP8165-LH
Rigid nose wing mounts are manufactured from
stainless steel.
Front Bumpers
Tubular front bumpers, in lightweight aluminum
or stainless steel, are 19" wide and 7" deep.
Description
HRP8165-LH .....LH Side Nose Wing Mount
HRP8165-RH .....RH Side Nose Wing Mount
HRP8018 ...........Wing Mount Clamps NEW
HRP8004-SS .....Nose Wing Tubes NEW
Part No.
HRP8018
HRP8004-SS
Radiator Air Box
Aluminum air box has lightening holes,
fully radiused edges and pre-formed
quick fastener flanges. Fits 20" wide
radiators in Maxim or Eagle chassis.
Part No.
Mount a Tel-Tac at the proper angle. Aluminum brackets install using
quick fasteners.
Prevents rocks or debris
from damaging air box. Sold complete with
honeycomb screen.
Rear Wing Trees
Part No.
Tel-Tac Dash Mount Brackets
HRP8362
K&N Air Box Guard
HRP8370
Nose Wing HRPVFT0801-S
Part No.
Aluminum gauge mount accepts 2-5/8" dia.
gauges and has a shut-off switch hole and
quick fastener flanges.
Description
HRP8300 ...........Air Box Channel
HRP8301 ...........Air Box Front Panel
Radiator Rock Screen
HRP8067
Rock screen, made of .050" thick aluminum with billet frame and fitted with a
stainless steel mesh, protects radiator from rocks and debris.
Description
HRP8075 ...........Aluminum Bumper
HRP8076 ...........Stainless Steel Bumper
Rear Bumper HRP8077
Stainless steel, 1" dia. bumper fits Maxim, Eagle
and Stealth chassis.
Nurf Bars
“Shorty” nurf bars are 1" dia.
stainless steel and fit Maxim, Triple X
and Eagle chassis.
Part No.
Description
HRP8078 ...........Left Hand Nurf Bar
HRP8079 ...........Right Hand Nurf Bar
Brake Pedal HRP8100
Manufactured from durable, 4130 chrome moly.
126
Heel Riser HRP8063
Wall Mount Spacer Tray HRP6181
Tapered aluminum heel riser is 1-1/2" tall
and mounts under the accelerator pedal for
improved leverage and comfort.
Aluminum tray is 23"
long, mounts on trailer
wall to keep axle spacers
in a convenient location.
Power Steering Top Plate
HRP8299
Sprint Car Wheel Wrench HRP6355
Billet aluminum, short top plate mounts
power steering box to chassis.
Designed to offer maximum leverage for loosening or tightening wheels.
King Pin Reamer HRP6107
Fuel Funnel Wall Rack
HRP6261
Constructed from durable stainless steel.
Aluminum rack stores a “D”-shaped
fuel funnel.
Torque Ball Shield HRP8225
Tire Gauge Holder
Protects driver’s legs and feet during a U-joint
failure.
Stores tire gauge in a convenient spot.
Part No.
Description
HRP6380 ...........Small Tire Gauge Holder
HRP6383 ...........Large Tire Gauge Holder
Torsion Bar Tray HRP6384
Header Rack HRP6700A
Lightweight aluminum tray, which may be
placed on the front or rear bumpers, eases
between race maintenance by providing a convenient area to place torsion bars, tools, etc.
Stainless steel rack hugs the trailer
wall and holds spare exhaust headers
tightly. Accepts spread port small
block Chevy headers. Sold each.
Trailer Accessories
HRP6776
Part No.
Ratchet Strap Holder
HRP6007
Keep ratchet straps organized with
this 8" long strap holder. Holds two tie
downs.
HRP6009
Description
HRP6009 ...........Nose Wing Tray
HRP6550 ...........Top Wing Wall Tray
HRP6553
HRP6551 ...........Top Wing Roof Mount
HRP6553 ...........Vertical Nose Wing Mount
HRP6776 ...........Axle Rack, Two Front Axles, One Rear End
HRP678-3 .........Steering Gear Wall Mount, Gen. 2
HRP6781 ...........Fuel Cell Wall Mount
Nitrogen Bottle Holder HRP6060
Two-piece holder keeps bottle secure.
HRP6781
Water Jacket Filler
Hard Blok will strengthen an engine block
and keep cylinder bores straighter and truer.
A specially formulated, cement-based material,
combined with iron particles, Hard Blok has the
same coefficient as cast iron so it will expand
and contract at the same rate as the engine
block. For circle track application, fill to bottom
of freeze plugs; usually a short fill will do this.
Hard Blok cannot be removed after it has hardened.
Part No.
Description
HBL860212 .......Short Fill Unit, Two 6-1/4 Lb. Bags
HBL860228 .......Tall Fill Unit, Two 14 Lb. Bags
Jason Cox
Photo By: John Berglund
127
Deluxe Helmet Bag HJCBAG
Helmet bag's durable outer shell and
soft inner liner protect helmet during
storage or transport. A removable inner
pocket stores extra shields and an extra
pocket has been added for pivot kits.
Molded handle eases carrying.
AR-10 II
The AR-10 II's fiberglass composite weave
shell is safe, comfortable and fits well. Advanced Channeling Ventilation System (ACS)
creates front to back air flow, flushing heat
and humidity up and out. Plush Nomex interior is removable and washable. The helmet
includes a polycarbonate anti-fog shield
with tear-off posts and meets Snell SA2010
specifications. White, or rubbertone black.
Size
White
Part No.
Rubbertone
Part No.
Small
Medium
Large
X-Large
XX-Large
HJC2WS10
HJC2WM10
HJC2WL10
HJC2WXL10
HJC2WXXL10
HJC2BS10
HJC2BM10
HJC2BL10
HJC2BXL10
HJC2BXXL10
Helmet Accessories
HJC2PK
Part No.
HJC2AM ................... Amber Helmet Shield AR10 II/SI-12
HJC2BL .................... RST Blue Helmet Shield AR10 II/SI-12
HJC2CL .................... Clear Helmet Shield AR10 II/SI-12
HJC2DA .................... Dark Smoke Helmet Shield AR10 II/SI-12
HJC2PK .................... Helmet Pivot Kit AR10 II
HJC6PK .................... Helmet Pivot Kit SI-12
HJCBP ...................... Back Plates for AR-10 II Helmets
Si-12
Innovative shell technology yields a light,
comfortable and safe helmet. Composite
weave shell has an Advanced Channeling Ventilation System (ACS) for front to
back air flow to flush heat and humidity
up and out. The Comfort Carbon Interior
is fire resistant and moisture-wicking. A
polycarbonate anti-fog shield with 95% UV
protection is included. The Si-12 meets Snell
SA2010 specifications and is available in white
or rubbertone black.
Size
White
Part No.
Rubbertone
Part No.
Medium
Large
X-Large
HJC6WM10
HJC6WL10
HJC6WXL10
HJC6BM10
HJC6BL10
HJC6BXL10
HJC2CL
Description
Fuel Injection Systems
Bill Tyler
Fuel injection units for small block Chevys
with 1957-up cylinder heads include sealed
nozzles for protection on dirt tracks. Please
call a sales associate with specific requirements. All fuel injection units are special order.
Ram tubes are not included and are sold individually.
Pills
Replacement pills are sold individually.
Part No.
Size
HILF565P-040 ....... .040"
HILF565P-045 ....... .045"
HILF565P-050 ....... .050"
HILF565P-055 ....... .055"
HILF565P-060 ....... .060"
HILF565P-065 ....... .065"
HILF565P-070 ....... .070"
HILF565P-075 ....... .075"
Part No.
Size
HILF565P-080 ...... .080"
HILF565P-085 ...... .085"
HILF565P-090 ...... .090"
HILF565P-095 ...... .095"
HILF565P-100 ...... .100"
HILF565P-105 ...... .105"
HILF565P-110 ...... .110"
HILF565P-115 ...... .115"
Part No.
Size
HILF565P-120 ......120"
HILF565P-125 ......125"
HILF565P-135 ......135"
HILF565P-140 ......140"
HILF565P-145 ......145"
HILF565P-150 ......150"
HILF565P-155 ......155"
HILF565P-160 ......160"
Brass Primary Bypass HILF510
Kevin Feeney
128
Photos By: Randy Ellen