doccatalog #18 - Mesa Tactical
download 
Report Transcription
catalog #18 - Mesa Tactical
GEAR AND ACCESSORIES FOR LAW ENFORCEMENT, MILITARY AND PERSONAL DEFENSE CATALOG #18 Prices valid for 90 days after August 1, 2013. Mesa Tactical is a manufacturer of tactical shotgun accessories for the professional operator. After starting out with telescoping shotgun stock systems in 2004, our SureShell™ shotshell carriers have become standard equipment among many US law enforcement agencies, with over 50,000 shipped. Our line of Urbino™ Tactical stocks for Benelli and Remington shotguns continues to gain enthusiastic adherents, as well as a new platform, the Remington Versa Max®. Our products are made in the USA of high quality materials. Mesa Tactical warrants that all products are free from defective material and workmanship and agrees to repair or replace any part of a product that proves defective by reason of improper workmanship or materials without charge for parts and labor. WHAT’S NEW As our product line has grown, we have been looking for ways to make it easier for our customers to determine their needs and configure their Mesa Tactical purchases. With this edition of our catalog, we have introduced product charts that list SKU numbers, prices and important distinguishing features to make selecting products less confusing. The weights in these charts are the packaged shipping weights. HOW TO ORDER For the best service, purchases should be made through an authorized Mesa Tactical dealer in your local area or on the Internet. Please give us a call at 949-642-3337 or visit our website to see if there is a dealer near you. Our new Mesa Tactical webstore is also open for business, and is one of the few places where our entire product line is available. Visit us at www.mesatactical.com. We can also accommodate credit card sales and international orders by phone at 714-545-3332 or by fax at 714-545-3339. Export status is indicted in the SKU charts. “NLR” indicates that no export license is required for most international destinations; items marked “License” cannot be exported without a US State Department export license. We offer a liberal test and evaluation (T&E) program for law enforcement and military customers. Simply mail or fax us a T&E product request on department letterhead and we will send you the items you request for a limited time test. In the listings, “Rem” is an abbreviation for Remington; “Moss” is short for Mossberg; and “Ben” indicates Benelli. 1135 Baker St., Costa Mesa, CA 92626 • Tel: 714-545-3332 • Fax: 714-545-3339 www.mesatactical.com Copyright © 2004-2013 Mesa Tactical. All rights reserved. 2 Mesa Tactical Catalog #18 CONTENTS Urbino Tactical Stock System............................................................................ 4 Urbino Tactical Stock Accessories.......................................................................6 Pocket Sling Attachments.....................................................................................6 Rear Hook Loop for Urbino stocks.....................................................................7 Telescoping Stock and Adapter Kits................................................................. 8 Telescoping Stock Adapter and Stock Kits.........................................................9 Hydraulic Recoil Buffer.........................................................................................9 Butt Pads and Recoil Buffers..............................................................................11 PGO Breaching Grips.........................................................................................12 Pocket Sling Attachments...................................................................................12 SureShell™ Shotshell Carriers........................................................................ 13 Side Mount SureShell Shotshell Carriers..........................................................13 Remington...................................................................................................13 Mossberg......................................................................................................14 Benelli...........................................................................................................14 FN SLP..........................................................................................................14 SureShell Shotshell Carriers with Rail..............................................................15 Remington...................................................................................................15 Mossberg......................................................................................................16 Benelli...........................................................................................................16 Kel-Tec KSG................................................................................................18 Adapter and Stock Mount SureShell Carriers..................................................19 Adapter Mount SureShell Shotshell Carriers..........................................19 Stock mount SureShell Shotshell Carriers...............................................19 Benelli Stock Mount..........................................................................19 SureShell Shotshell Carriers for the Urbino Tactical Stock..........20 M4 SOPMOD Buttstock Mount SureShell Shotshell Carriers.....20 Barrel and Magazine Clamps.......................................................................... 21 Picatinny Rails.................................................................................................. 22 Receiver Mount Picatinny Rails.........................................................................22 Remington Saddle Rails.............................................................................22 Remington Side Mount Rail......................................................................23 Rails for Drilled and Tapped Receivers....................................................23 Adapter Mount Picatinny Rails.........................................................................24 Hook Loops...................................................................................................... 26 Magazine Extension Hook Loops......................................................................26 Rear Hook Loops for Benelli Tactical Stocks...................................................26 www.mesatactical.com3 URBINO TACTICAL STOCK SYSTEM #91550 Urbino Tactical Stock for Remington (Cheek Riser, Limbsaver, 12-GA) Developed to meet the needs of law enforcement and military operators, the rugged Urbino Tactical stock features a “tactical” 12½ inch length of pull (LoP), Santoprene rubber grip, optional Limbsaver® butt pad, optional adjustable cheek riser and a variety of flexible sling mounting options. The reduced LoP makes the Urbino the first truly tactical stock for the Benelli shotguns. A shorter stock is necessary for use in tactical applications, especially with body armor. The Urbino Tactical stock is durable, easy to shoulder and will not slip. The Urbino Tactical stock is also comfortable, thus reducing operator fatigue, especially during prolonged training and qualification sessions. The Santoprene grip is padded at the rear to reduce recoil impact against the web of the operator’s hand, and the optional Limbsaver buttpad substantially reduces felt recoil. #90170 The field-adjustable cheek riser was develSureShell Carrier for Urbino Cheek Riser (6-Shell, 12-GA) oped to provide superior cheek weld when using (Left Side) optics. The cheekpiece snaps onto rails molded into the sides of specially equipped Urbino stock armatures. In the event of optics failure, the cheek riser can be quickly removed or readjusted to a lower level. Specially-developed SureShell™ shotshell carriers can be fitted to the cheek riser (see page 20). While railequipped Urbino stocks can be used without the cheekpiece, cheek risers cannot be fitted to stocks that do not have the rails. All Urbino Tactical stocks are made in the USA, and include Benelli-style rear sling loops for 1¼ inch sling webbing. In addition, a hole at the lower rear of the stock accepts QD style sling swivels. Urbino Tactical stocks for the Benelli M4 are available in black, coyote (tan), OD green or flat dark earth (FDE) colors. We also offer US-made forend halves from Freedom Fighter Tactical that match the colored Urbino Tactical stocks. Colored Urbino Tactical #90570 Replacement Forend stock kits include matching forends. for Benelli M4 (12-GA, Coyote) #92740 Urbino Tactical Stock and Forend for Ben M4 (Riser, Standard Butt, 12-GA, Coyote) 4 Mesa Tactical Catalog #18 In the chart below, Urbino Tactical stocks for the Benelli M2 can typically be fitted to Benelli M1 and Benelli M3 shotguns as well. There may be minor fitting required with some older Benelli M1 shotguns. #91460 Urbino Tactical Stock for Ben M4 (Limbsaver, 12-GA, Black) URBINO TACTICAL STOCK SYSTEM Part # 90070 91540 90080 91550 93490 93510 93500 93520 90050 91500 90060 91510 90030 91460 90040 91470 91650 91660 92770 92790 92780 92800 92730 92750 92740 92760 93130 93150 93140 93160 92410 92430 92420 92440 Item Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip (Riser Ready) Pistol Grip (Riser Ready) Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Pistol Grip Platform Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem Versa Max Rem Versa Max Rem Versa Max Rem Versa Max Benelli M2 Benelli M2 Benelli M2 Benelli M2 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Benelli M4 Ben SuperNova Ben SuperNova Ben SuperNova Ben SuperNova Limbsaver Cheek Riser w/Forend Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No* No* Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Color Black Black Black Black Black Black Black Black Black Black Black Black Black Black Black Black Black Black OD OD OD OD Coyote Coyote Coyote Coyote FDE FDE FDE FDE Black Black Black Black Caliber Weight Export MSRP 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR $100.00 125.00 130.00 155.00 110.00 135.00 140.00 165.00 115.00 140.00 145.00 170.00 115.00 140.00 145.00 170.00 120.00 145.00 165.00 190.00 195.00 220.00 165.00 190.00 195.00 220.00 165.00 190.00 195.00 220.00 115.00 140.00 145.00 170.00 33 oz 34 oz 38 oz 38 oz 33 oz 30 oz 38 oz 35 oz 29 oz 30 oz 34 oz 35 oz 30 oz 30 oz 35 oz 36 oz 30 oz 30 oz 30 oz 31 oz 35 oz 36 oz 30 oz 31 oz 35 oz 36 oz 30 oz 31 oz 35 oz 36 oz 30 oz 30 oz 35 oz 36 oz * “Riser Ready” Urbino Tactical stocks, available for the Benelli M4, feature cheek riser stock armatures without the cheek risers. Cheek risers can be purchased separately at any time and fitted to “Riser Ready” stocks (see page 6). www.mesatactical.com5 URBINO TACTICAL STOCK ACCESSORIES #90180 Standard Buttpad for Urbino Tac Stock (Coyote) Individual components of the Urbino Tactical stock system can be purchased separately. Except for Freedom Fighter forends, the following items will fit on any supported shotgun platform. Note that cheek risers can only be fitted to Urbino Tactical stocks that include molded side support rails. All Limbsaver Buttpads are black, fitted to a colored buttplate as indicated URBINO TACTICAL STOCK ACCESSORIES Part # 90520 90180 94150 90350 92510 92530 93110 91700 90530 90190 94160 90360 92520 92540 93120 91710 91690 94530 94550 94540 90570 94180 92900 Item Standard Buttpad Standard Buttpad Standard Buttpad Standard Buttpad Standard Buttpad Standard Buttpad Standard Buttpad Standard Buttpad Limbsaver® Buttpad Limbsaver® Buttpad Limbsaver® Buttpad Limbsaver® Buttpad Limbsaver® Buttpad Limbsaver® Buttpad Limbsaver® Buttpad Limbsaver® Buttpad Cheek Riser Cheek Riser Cheek Riser Cheek Riser Freedom Fighter Tactical Forend Freedom Fighter Tactical Forend Freedom Fighter Tactical Forend Platform Riser Color Weight Export MSRP No Riser No Riser No Riser No Riser Cheek Riser Cheek Riser Cheek Riser Cheek Riser No Riser No Riser No Riser No Riser Cheek Riser Cheek Riser Cheek Riser Cheek Riser Required Required Required Required Black Coyote FDE OD Black Coyote FDE OD Black Coyote FDE OD Black Coyote FDE OD Black Coyote FDE OD Coyote FDE OD 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 6 oz 10 oz 10 oz 10 oz 10 oz 8 oz 8 oz 8 oz NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR $25.00 35.00 35.00 35.00 25.00 35.00 35.00 35.00 50.00 60.00 60.00 60.00 50.00 60.00 60.00 60.00 30.00 40.00 40.00 40.00 50.00 50.00 50.00 Benelli M4 Benelli M4 Benelli M4 POCKET SLING ATTACHMENTS The Urbino Tactical stock system features a molded pocket at the front where the stock meets the shot#91780 gun receiver. A nylon blank is provide to fill this Pocket Ambi Hook Loop for pocket, but it can also accept any of several stamped Urbino Tactical steel Sling Loops, Hook Loops or Push Button Stock for Benelli M4 (12-GA) Sling Swivel mounts. The Push Button Sling Swivel mount includes a US-made Push Button Sling Swivel, and all the sling mounts feature a tough Mil-spec manganese phosphate finish. Ambi-style sling attachments feature mounts on both sides of the receiver. 6 Mesa Tactical Catalog #18 POCKET SLING ATTACHMENTS URBINO STOCKS Part # 91570 91610 93980 94000 91880 91900 91760 91780 92460 92480 91560 91600 93970 93990 91870 91890 91750 91770 92450 92470 91520 91530 94010 94020 91440 91450 91480 91490 92490 92500 Item Hook Loop Hook Loop Hook Loop Hook Loop Hook Loop Hook Loop Hook Loop Hook Loop Hook Loop Hook Loop Sling Loop Sling Loop Sling Loop Sling Loop Sling Loop Sling Loop Sling Loop Sling Loop Sling Loop Sling Loop Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Push Button Sling Mount Platform Caliber Rem 870/1100/11-87 Rem 870/1100/11-87 Rem Versa Max Rem Versa Max Benelli M2 Benelli M2 Benelli M4 Benelli M4 Ben SuperNova Ben SuperNova Rem 870/1100/11-87 Rem 870/1100/11-87 Rem Versa Max Rem Versa Max Benelli M2 Benelli M2 Benelli M4 Benelli M4 Ben SuperNova Ben SuperNova Rem 870/1100/11-87 Rem 870/1100/11-87 Rem Versa Max Rem Versa Max Benelli M2 Benelli M2 Benelli M4 Benelli M4 Ben SuperNova Ben SuperNova 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA Ambidextrous Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Sling Style Weight Export MSRP H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook 1¼ in Sling 1¼ in Sling 1¼ in Sling 1¼ in Sling 1¼ in Sling 1¼ in Sling 1¼ in Sling 1¼ in Sling 1¼ in Sling 1¼ in Sling Push Button Push Button Push Button Push Button Push Button Push Button Push Button Push Button Push Button Push Button 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 1 oz 2 oz 1 oz 1 oz 1 oz 1 oz 1 oz 2 oz 2 oz 2 oz 1 oz 2 oz 2 oz 2 oz 2 oz 2 oz 1 oz 2 oz NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR $12.00 14.00 12.00 14.00 12.00 14.00 12.00 14.00 17.00 19.00 12.00 14.00 12.00 14.00 12.00 14.00 12.00 14.00 17.00 19.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 30.00 30.00 REAR HOOK LOOP FOR URBINO STOCKS The Urbino Tactical stocks include stamped steel sling plates that mimic the factory Benelli rear sling plates. We have produced replacement stampings that feature a circular hook loop instead of the sling loop for use with increasingly popular H&K style (dog leash) sling hooks. These hook loops are stamped steel with a tough Mil-spec manganese phosphate finish. REAR HOOK LOOPS FOR URBINO STOCK Part # 91790 91800 91810 91820 Item Rear Hook Loop Rear Hook Loop Rear Hook Loop Rear Hook Loop Platform Caliber Rem 870 Rem 1100/11-87 Benelli M2 Benelli M4 12 GA 12 GA 12 GA 12 GA Ambidextrous Sling Style Weight Export MSRP H&K Hook H&K Hook H&K Hook H&K Hook 1 oz 1 oz 1 oz 1 oz NLR NLR NLR NLR $12.00 12.00 12.00 12.00 www.mesatactical.com7 TELESCOPING STOCK AND ADAPTER KITS The concept behind the telescoping stock system is simple: the shotgun stock is replaced by an adapter, which #91260 LEO Telescoping Stock Kit attaches to the rear end of the shotgun’s for Rem 870 receiver and it, in turn, mimics the rear end of an AR-15 lower receiver, into which an AR-15 receiver extension tube can be threaded. The AR-15 telescoping stock and pistol grip can then be reliably attached. Our stock adapters, manufactured for the Remington 870 and Mossberg 500/590, are investment cast aircraft aluminum. They are then CNC machined and anodized with a Type III Class 2 Mil-spec finish. To meet the requirements of professional operators as well as competitors, we offer two lines of telescoping stock systems: High-tube™ and LEO. The LEO adapter is our most basic, best-selling model, and features an optimal stock elevation allowing the use of iron sights or even the bead sight. All LEO adapters accept optional push-button sling swivels, and Remington 870 LEO adapters can accept stamped steel sling loop and hook loops. #93180 LEO Telescoping Stock Kit Our High-tube adapters, which feature a for Moss 500/590 much higher stock elevation (equivalent to an AR-15) and require an optics rail (included), are specialized adapters for unusual law enforcement #90500 High-tube Telescoping applications or competition. AccesStock and Rail Kit for sory mounting points on the sides of the High-tube Rem 870 aluminum adapters accept Picatinny rails or Mesa Tactical shell carriers, and are fitted with Timesert® steel thread inserts for strength and long life. High-tube adapters and stock kits include nine inch or 24-inch top Picatinny optics rails. The 24-inch rails are anchored at the front by a clamp. The Remington #92040 High-tube Telescoping Stock Kit for Moss 500 (QD Swivel Clamp, 24 in rail) 8 Mesa Tactical Catalog #18 versions are available with a barrel clamp or a magazine clamp, or no clamp at all (for customers who already have clamps); the Mossberg rails use a magazine clamp that features either a short length of Picatinny accessory rail at the bottom, or a sling swivel stud. No gunsmithing is required to install. Minor fitting of fasteners may be necessary. #90740 High-tube Telescoping Stock and Rail Kit for Moss 500/590 (receiver rail) TELESCOPING STOCK ADAPTER AND STOCK KITS Our aluminum adapter kits include everything necessary to retrofit Remington or Mossberg pump shotguns with most AR-15 style stocks and pistol grips. Our adapt#91250 er kits allow customers to add their own AR-15 stock as- LEO Telescoping Stock Adapter for Rem 870 semblies as desired. Our complete stock kits are more comprehensive. They include the aluminum AR adapter; Hogue rubber overmolded grip; US-made Mil-spec four-position M4 SOPMOD style telescoping stock assembly; and all necessary assembly hardware and instructions. The High-tube stock kits also include a receiver-length top Picatinny rail. A Telescoping Shotgun Stock Multi-tool and push-button sling swivel are included with every stock kit. HYDRAULIC RECOIL BUFFER The ITT Enidine hydraulic recoil buffer can take the place of the receiver extension tube, converting the AR-15 telescoping stock into #92230 a recoil-buffered stock assembly without furLEO Telescoping Hydraulic Recoil ther modification. Recoil-buffered versions Stock Kit for Rem 870 (12-GA) are available for all three of the telescoping stock systems, or the recoil buffer can be purchased separately (see page 11). The recoil buffer accepts Mil-spec dimensioned buttstocks. The ITT Enidine recoil buffer is CNC machined from 6061-T6 aluminum and meets the stringent standards of military and law enforcement users. Our basic kits include the adapter and all necessary installation hardware. No gunsmithing is required for installation. #93220 LEO Telescoping Hydraulic Recoil Stock Kit for Moss 500 (12-GA) www.mesatactical.com9 TELESCOPING STOCK KITS AND ADAPTERS Part # Item Platform Style Type LEO TELESCOPING STOCK 91250 Adapter Rem 870 LEO 93170 Adapter Moss 500 LEO 91260 Stock Kit Rem 870 LEO 93180 Stock Kit Moss 500 LEO 92230 Hydraulic Recoil Rem 870 LEO 93220 Hydraulic Recoil Moss 500 LEO HIGH-TUBE TELESCOPING STOCK 90630 Adapter and Rail Rem 870 High-tube 90950 Adapter and Rail Rem 870 High-tube 91000 Adapter and Rail Rem 870 High-tube 91010 Adapter and Rail Rem 870 High-tube 90620 Adapter and Rail Moss 500 High-tube 90780 Adapter and Rail Moss 500 High-tube 90500 Stock Kit Rem 870 High-tube 94510 Stock Kit Rem 870 High-tube 92050 Stock Kit Rem 870 High-tube 92060 Stock Kit Rem 870 High-tube 90490 Stock Kit Moss 500 High-tube 90740 Stock Kit Moss 500 High-tube 91020 Stock Kit Moss 500 High-tube 91030 Stock Kit Moss 500 High-tube 92030 Stock Kit Moss 500 High-tube 92040 Stock Kit Moss 500 High-tube 92290 Hydraulic Recoil Rem 870 High-tube 94520 Hydraulic Recoil Rem 870 High-tube 92090 Hydraulic Recoil Rem 870 High-tube 92100 Hydraulic Recoil Rem 870 High-tube 92280 Hydraulic Recoil Moss 500 High-tube 92220 Hydraulic Recoil Moss 500 High-tube 92070 Hydraulic Recoil Moss 500 High-tube 92080 Hydraulic Recoil Moss 500 High-tube Rail Rail Len. Clamp Adapter Adapter Stock Kit Stock Kit Stock Kit Stock Kit Adapter Adapter Adapter Adapter Adapter Adapter Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Adapter Adapter Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Stock Kit Yes Yes Yes Yes Adapter* Receiver* Yes Yes Yes Yes Adapter* Receiver* Yes Yes Yes Yes Yes Yes Yes Yes Adapter* Receiver* Yes Yes 9 in 24 in 24 in 24 in 9 in 5 in 9 in 24 in 24 in 24 in 9 in 5 in 24 in 24 in 24 in 24 in 9 in 24 in 24 in 24 in 9 in 5 in 24 in 24 in None None Barrel Magazine None Barrel Magazine Pic Rail Swivel Pic Rail Swivel None Barrel Magazine Pic Rail Swivel Caliber Weight Export MSRP 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 11 oz 10 oz 31 oz 31 oz 40 oz 40 oz NLR NLR NLR NLR NLR NLR $70.00 75.00 190.00 195.00 325.00 330.00 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 25 oz 38 oz 38 oz 38 oz 22 oz 20 oz 41 oz 62 oz 45 oz 45 oz 38 oz 36 oz 38 oz 38 oz 45 oz 45 oz 50 oz 62 oz 62 oz 62 oz 48 oz 46 oz 62 oz 62 oz NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR 160.00 285.00 340.00 340.00 165.00 165.00 280.00 405.00 460.00 460.00 285.00 285.00 345.00 345.00 465.00 465.00 415.00 540.00 595.00 595.00 420.00 420.00 600.00 600.00 * Mossberg 500 kits are available with adapter-mount rail or receiver mount rail. The receiver mount rail is recommended. It can be installed on post-1996 Mossberg shotguns with factory-tapped mounting holes in the top of the receiver, and allows access to the Mossberg tang safety switch. ACCESSORIES Part # Item 93070 Receiver Extension Tube (Mil-spec) 92170 Enidine Shot Stock Hydraulic Buffer (Mil-spec) SOPMOD Telescoping Hydraulic Recoil Stock 92180 M4 (Mil-spec) 10 Platform Style Recoil Weight Export All All M4 SOPMOD Stock M4 SOPMOD Stock Hydraulic 4 oz 17 oz License License 40.00 150.00 All M4 SOPMOD Stock Hydraulic 28 oz License 180.00 Mesa Tactical Catalog #18 MSRP BUTT PADS AND RECOIL BUFFERS Because those M4 telescoping stocks were not designed with shotguns in mind, they aren’t the most comfortable buttstocks. We recommend you use some kind of butt pad, and we offer two styles. USGI-style slipon rubber butt pads expand the butt’s sur#92170 Enidine Shot Stock Hydraulic face area and make it easier and more comBuffer (Mil-spec) fortable to shoulder and fire your weapon, though they do not offer any recoil absorption. LimbSaver slip-on recoil pads feature a patented three-step recoil reduction technology that reduces up to 70% of felt recoil, and maintains target acquisition. They feature a #92180 M4 SOPMOD Telescoping 12-month warranty by Limbsaver. Hydraulic Recoil Stock Any Mesa Tactical telescoping stock kit (Mil-spec) can be upgraded with an ITT Enidine hydraulic recoil buffer to reduce felt recoil by up to 70%. These hydraulic recoil buffer assemblies are guaranteed by ITT Enidine for 20 million cycles, and replace the receiver extension tubes in our stock kits. Purchase either a complete replacement M4 SOPMOD recoil buttstock assembly, or the “drop in” hydraulic buffer alone (stock nut sold separately, see chart). Additional Limbsaver and standard rubber buttpads for the Urbino Tactical stocks can also be ordered separately (see page 6). BUTT PADS AND RECOIL BUFFERS Part # 92810 93310 91200 91850 90450 90560 90860 93070 92170 92180 Item Platform CAR Stock Lock Nut ERGO Grip® Hogue Rubber Overmolded Combat Grip LimbSaver® Snap-on Recoil Pad Hard Rubber Butt Pad Telescoping Shotgun Stock Multi-tool Trigger Pin Replacement Kit forRemington Receiver Extension Tube (Mil-spec) Enidine Shot Stock Hydraulic Buffer (Mil-spec) M4 SOPMOD Telescoping Hydraulic Recoil Stock (Mil-spec) Stock Style Weight Export MSRP M4 SOPMOD Stock PGO Adapter AR Adapter M4 SOPMOD Stock M4 SOPMOD Stock License License License License License NLR NLR License License $ 6.00 26.00 26.00 40.00 16.00 8.50 12.00 40.00 150.00 License 180.00 Rem 870/1100/11-87 All All M4 SOPMOD Stock M4 SOPMOD Stock 1 oz 3 oz 3 oz 4 oz 3 oz 3 oz 1 oz 4 oz 17 oz All M4 SOPMOD Stock 28 oz Rem 870 Moss 500, Rem 870 www.mesatactical.com11 PGO BREACHING GRIPS #92830 PGO adapters and grips answer the profesPGO with ERGO Grip for Rem 870 sional’s desire for a breaching grip with the same robust high quality as our LEO telescoping stock adapters. Cast from aircraft aluminum, the PGO adapter accepts any AR-15 grip and features a horn at the rear to make it the most comfortable breaching style grip on the market. The adapter is available separately, or bundled with the rubber overmolded ERGO Grip®. #92820 PGO Adapter for Rem 870 PGO BREACHING GRIPS Part # Item 92820 PGO Adapter 92830 PGO w/ ERGO Grip Platform Style Type Grip Caliber Weight Export MSRP Rem 870 Rem 870 Pistol Grip Only Pistol Grip Only Adapter Adapter None Ergo Grip 12 GA 12 GA 10 oz 13 oz NLR NLR $60.00 80.00 POCKET SLING ATTACHMENTS All our telescoping stock adapter designs for the Remington 870, as well as the PGO adapter, include a pocket between the adapter and the shotgun receiver that accepts steel sling sloops or hook loops. These sling mounts are stamped steel with a tough Mil-spec manganese phosphate finish. POCKET SLING ATTACHMENTS FOR REMINGTON Part # 91380 91400 91370 91390 Item Platform Caliber Hook Loop for AR and PGO Adapter Hook Loop for AR and PGO Adapter Sling Loop for AR and PGO Adapter Sling Loop for AR and PGO Adapter Rem 870 Rem 870 Rem 870 Rem 870 12 GA 12 GA 12 GA 12 GA Ambidextrous Yes Yes #91380 Pocket Hook Loop for Remington Stock and PGO Adapters 12 Mesa Tactical Catalog #18 Sling Style Weight Export MSRP H&K Hook H&K Hook 1¼ in Sling 1¼ in Sling 1 oz 1 oz 1 oz 1 oz NLR NLR NLR NLR $10.00 12.00 10.00 12.00 #91390 Pocket Ambi Sling Loop for Remington Stock and PGO Adapters SURESHELL™ SHOTSHELL CARRIERS #92000 SureShell Carrier and Rail for Benelli SuperNova (4-Shell, 12-GA) Our SureShell shotshell carriers retain ammunition reliably and, being metal, can withstand the rigors of daily use and abuse. Fabricated from aircraft aluminum, they feature an innovative rubber friction retention system and tough construction to endure years of use and abuse. Since their introduction in the spring of 2005, they have rapidly become our bestselling accessories, and an emerging industry standard. SureShell carrier yokes are milled from 6061-T6 aircraft aluminum, then bead blasted and Mil-spec hard anodized for a rugged non-glare finish. SureShell yokes are secured to application-specific brackets, and some SureShell carriers include high temperature adhesive-backed die-cut rubber gaskets to protect the host shotgun’s finish. SIDE MOUNT SURESHELL SHOTSHELL CARRIERS Most of our SureShell shotshell carriers mount directly to the receiver of leading shotgun platforms. REMINGTON #90320 SureShell Carrier for Remington 870 (4-Shell, 12-GA) (left side) The receiver mounting scheme of our receiver mount SureShell carriers for the Remington shotguns uses a combination of steel fasteners threaded into a steel pin (at the rear) and paired Chicago screws (up front) for more secure attachment to the shotgun without the risk of pinching the receiver. The mounting plate even features a window over the shotgun serial number location, to make it easier for armorers to inventory their weapons. Note that SureShell shotshell carriers cannot be installed on the right side of Remington semi-auto shotguns. To use a six- and eight-shot SureShell carrier mounted on the left side of the Remington 870 shotgun, you must use a tactical forend that does not overlap the receiver, or a factory forend that is cut down #93250 SureShell Carrier for appropriately. SureFire® forends are fully Remington 870 (6-Shell, 20-GA) compatible with our six-shot SureShell carriers, but will need about ½ inch shaved off the end to be installed with our eight-shot SureShell carriers. Remington side mount SureShell carriers are available in both 12-gauge and 20-gauge models. www.mesatactical.com13 MOSSBERG #90390 SureShell Carrier for Moss 500/590 (6-Shell, 12-GA) The side mount scheme of our shotgun SureShell shotshell carriers for the Mossberg 500/590 substitutes two custom-machined steel Chicago screws for the trigger pin. At the front of the mounting plate, custom retaining steel hardware is used with an elongated extractor screw and a machined key hole in the plate. The Mossberg 930 mounting system is similar, except it uses two sets of Chicago screws in place of the two trig#93040 SureShell Carrier for Moss 930 ger pins. The mounting plate was (8-Shell, 12-GA) designed not to obscure the receiver serial number to make it easier for armorers to inventory their weapons. SureShell shotshell carriers for the Mossberg fit on the left side of the receiver only. You must use a tactical forend that does not significantly overlap the receiver, or a factory forend that is cut down appropriately. SureFire forends will work fine with no alterations. #90830 SureShell Carrier for Benelli M1/M2 (4-Shell, 12-GA) BENELLI Our side mount shotgun SureShell shotshell carriers for the Benelli M1/M2 substitute custommade steel Chicago screws for the trigger pin. The mounting plate is curved to hug the shotgun receiver, preventing movement of the SureShell assembly. SureShell shotshell carriers for the Benelli M1/M2 fit on the left side of the receiver only; they are known to fit onto Benelli M3 shotguns as well as M1 and M2 models. Extra weight on the weapon may adversely affect the reliable cycling of inertia-operated shotguns such as the #90850 Benelli M1 or M2 when used with low-recoil SureShell Carrier for Ben M1/M2/M3 (8-Shell, ammunition. 12-GA) FN SLP The mounting system for the SureShell carrier for the FN Self-loading Police shotgun is similar to that of the Mossberg 930, with two sets of Chicago screws in place of the two trigger pins. SureShell shotshell carriers for the FN SLP fit on the left side of the receiver only, and will not interfere with the forend. 14 Mesa Tactical Catalog #18 #90110 SureShell Carrier for FN SLP (4-Shell, 12-GA) SIDE MOUNT SURESHELL SHOTSHELL CARRIERS Part # 90320 90600 90210 90420 93240 93230 93250 93260 91240 90390 90340 93020 93030 93040 90830 90840 90850 90110 90120 90130 Item SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier SureShell Carrier Platform Caliber Shells Side Mount Weight Export MSRP Rem 870/1100/11-87 Rem 870 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870 Rem 870/1100/11-87 Rem 870/1100/11-87 Moss 500/590 Moss 500/590 Moss 500/590 Moss 930 Moss 930 Moss 930 Benelli M2 Benelli M2 Benelli M2 FN SLP FN SLP FN SLP 12 GA 12 GA 12 GA 12 GA 20 GA 20 GA 20 GA 20 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 4 shell 4 shell 6 shell 8 shell 4 shell 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell Left Right Left Left Left Right Left Left Left Left Left Left Left Left Left Left Left Left Left Left Side Side Side Side Side Side Side Side Side Side Side Side Side Side Side Side Side Side Side Side 7 oz 7 oz 8 oz 10 oz 7 oz 7 oz 9 oz 10 oz 6 oz 8 oz 10 oz 6 oz 8 oz 10 oz 9 oz 9 oz 11 oz 6 oz 8 oz 10 oz NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR $65.00 65.00 70.00 85.00 65.00 65.00 70.00 85.00 70.00 75.00 90.00 70.00 75.00 90.00 70.00 75.00 90.00 75.00 80.00 95.00 SURESHELL SHOTSHELL CARRIERS WITH RAIL Mesa Tactical offers two methods for mounting SureShell shotshell carriers to Remington 870, Remington 1100 and Remington 11-87 shotguns. Our traditional side mount SureShell carriers attach via flat aluminum brackets to the sides of the shotgun receiver. We also offer unique saddle rail SureShell carriers that combine a shell carrier with a MIL-STD-1913 (NATO STANAG 4694) Picatinny rail that accepts optical sights. REMINGTON #91950 SureShell Carrier and Rail for Remington w/ Barrel Clamp (6-Shell, 12-GA, 20 inch) Mesa Tactical Saddle Rails are aluminum brackets that wrap around the top of the shotgun receiver, with a Picatinny optics rail at the top. The factory trigger pins are replaced by an internally threaded steel pin (in the rear) and paired Chicago screws (up front), to which both sides of the saddle rail are securely bolted. SureShell Saddle Rails feature a MIL-STD-1913 (NATO STANAG 4694) Picatinny sight rail along the top, and a four-, six- or eight-shot SureShell shotshell carrier yoke on the left side of the receiver. The rail is notched #91630 Carrier and Rail at the rear to accommodate Scattergun/Wilson style ghost ring SureShell for Remington sights, and extends to the front of the shotgun receiver (5-inch (6-Shell, 12-GA, 5 inch) rail), 2¾ inches past the front of the receiver (8½ inch rail), or just beyond the bar www.mesatactical.com15 rel’s magazine lug (20-inch rail). The 20-inch rails are anchored at the front by a clamp. They are available with a barrel clamp or a magazine clamp, or no clamp at all (for customers who already have clamps). No gunsmithing is required to install the SureShell Saddle Rail, except for optional forend alterations as described above under side mount carriers. Saddle Rails are also available without the shell carriers (see page 22) MOSSBERG These SureShell shotshell carriers for #93600 SureShell Carrier and the Mossberg 500 and 590 feature mounting brackets Rail for Moss 500 w/ QD Swivel Clamp (6-Shell, with integral top Picatinny sight rails. The brackets 12-GA, 20 in) are secured to the weapon using the top mounting #93630 screw holes found on Mossberg 500 and 590 shotSureShell Carrier and Rail for Moss guns made since 1997. The SureShell shotshell car500 (6-Shell, 12-GA, 4½ in) riers are thus slung on the left side of the receiver, securely fastened at the top. No other shell carrier mounting method is as secure or looks as good. The 20-inch rails are anchored at the front by a magazine clamp that features either a short length of Picatinny accessory rail at the bottom, or a sling swivel stud. #90880 SureShell Carrier and Rail for Benelli M4/M1014 (6-Shell, 12-GA, 5½ in) BENELLI While the Benelli M2 Tactical semi-automatic and Benelli SuperNova® pump-action shotgun feature factory-tapped rail mounting holes in the top of the receiver, the Benelli M4 and M1014 are shipped with a top Picatinny sight rail. These provided us with an opportunity to develop SureShell shotshell carrier mounting solutions for Benelli shotguns that are streamlined and very robust. Receiver mount SureShell shotshell carriers for the Benelli M2, M4 and M1014 feature mounting brackets with integral top Picatinny sight rails. These brackets are secured to the weapon using the top mounting screw holes. The SureShell shotshell carriers are thus slung on the left side of the receiver, securely fastened at the top. No other shell carrier mounting method is as secure or looks as good. SureShell shotshell carriers for the Benelli M2 Tactical can be installed on Benelli M1 shotguns with round- SureShell#91210 Carrier and Rail M2 Tactical (4-Shell, top receivers by tapping the top of the shotgun for Ben12-GA, 4½ in) receiver with #8-40 threads. Consult a gunsmith. 16 Mesa Tactical Catalog #18 Extra weight on the weapon may adversely affect the reliable cycling of inertiaoperated shotguns such as the Benelli M1 or M2 when used with low-recoil ammunition. The Benelli M4 is gas-operated and has no such sensitivity. SURESHELL SHOTSHELL CARRIERS WITH RAILS Part # Item 92160 91630 91640 92700 92710 92720 91970 91980 91990 91940 92120 91950 92130 91960 92140 93620 93630 93640 93560 93590 93570 93600 93580 93610 91210 91220 91230 90870 90880 90890 92000 92010 92020 92950 92960 92970 92980 92990 93000 Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Carrier & Rail Platform Caliber Shells Side Length Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Moss 500/590 Moss 500/590 Moss 500/590 Moss 500/590 Moss 500/590 Moss 500/590 Moss 500/590 Moss 500/590 Moss 500/590 Benelli M2 Benelli M2 Benelli M2 Benelli M4 Benelli M4 Benelli M4 Ben SuperNova Ben SuperNova Ben SuperNova Kel-Tec KSG Kel-Tec KSG Kel-Tec KSG Kel-Tec KSG Kel-Tec KSG Kel-Tec KSG 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell 4 shell 4 shell 6 shell 6 shell 8 shell 8 shell 4 shell 6 shell 8 shell 4 shell 4 shell 6 shell 6 shell 8 shell 8 shell 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell 4 shell 6 shell 8 shell 4 shell 4 shell 8 shell 6 shell 6 shell 12 shell Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Left Right Both Left Right Both 5 in 5 in 5 in 8½ in 8½ in 8½ in 20 in 20 in 20 in 20 in 20 in 20 in 20 in 20 in 20 in 4½ in 4½ in 4½ in 20 in 20 in 20 in 20 in 20 in 20 in 4½ in 4½ in 4½ in 5½ in 5½ in 5½ in 5½ in 5½ in 5½ in 13 in 13 in 13 in 13 in 13 in 13 in Clamp None None None Barrel Magazine Barrel Magazine Barrel Magazine Pic Rail Swivel Pic Rail Swivel Pic Rail Swivel Mount Weight Export Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Saddle Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top Top 11 oz 12 oz 14 oz 13 oz 14 oz 16 oz 23 oz 25 oz 25 oz 27 oz 26 oz 27 oz 26 oz 28 oz 28 oz 9 oz 9 oz 12 oz 27 oz 27 oz 27 oz 27 oz 30 oz 30 oz 8 oz 9 oz 11 oz 8 oz 8 oz 11 oz 8 oz 10 oz 11 oz 27 oz 27 oz 35 oz 29 oz 29 oz 37 oz NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR MSRP $120.00 125.00 140.00 135.00 140.00 155.00 180.00 185.00 200.00 235.00 235.00 240.00 240.00 255.00 255.00 115.00 120.00 135.00 250.00 250.00 255.00 255.00 270.00 270.00 105.00 110.00 125.00 105.00 110.00 125.00 105.00 110.00 125.00 210.00 210.00 250.00 215.00 215.00 255.00 www.mesatactical.com17 KEL-TEC KSG #93000 SureShell Carrier and Rail for Kel-Tec KSG (12-Shell, 12-GA, Both Sides) The SureShell carrier system for the Kel-Tec KSG comprises a replacement anodized aluminum Picatinny optics rail which supports one or two machined shell carrier yokes. Small aluminum flanges on either side of the main rail can accept additional lengths of Picatinny rail to support weapon lights or targeting lasers (rail not included, see page 24). A pair of unique steel recoil blocks featuring angled set screws ensure the rail assembly is securely mounted to the shotgun. SureShell carriers for the Kel-Tec KSG feature four- or six-shell yokes, on the left side or right side or both sides. A replacement Picatinny rail without SureShell yokes is also available, see page 23. 18 Mesa Tactical Catalog #18 ADAPTER AND STOCK MOUNT SURESHELL CARRIERS ADAPTER AND STOCK MOUNT SURESHELL SHOTSHELL CARRIERS Part # 90370 90380 90610 91840 91830 90140 90160 90150 90170 93340 93350 Item Adapter Mount Carrier Adapter Mount Carrier Adapter Mount Carrier Stock Mount Carrier Stock Mount Carrier (Hook Loop)* Stock Mount Carrier Stock Mount Carrier Stock Mount Carrier Stock Mount Carrier Stock Mount Carrier Stock Mount Carrier Platform Caliber Shells High-tube High-tube High-tube Benelli Stock (Not M4) Benelli Stock (Not M4) Urbino Riser Urbino Riser Urbino Riser Urbino Riser M4 SOPMOD Stock M4 SOPMOD Stock 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 4 shell 6 shell 8 shell 4 shell 4 shell 4 shell 4 shell 6 shell 6 shell 4 shell 6 shell Side Weight Export MSRP Right Left Right Left Right Right 6 oz 8 oz 9 oz 8 oz 8 oz 7 oz 7 oz 9 oz 8 oz 7 oz 9 oz NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR $ 65.00 70.00 85.00 55.00 60.00 70.00 70.00 75.00 75.00 65.00 70.00 * This item includes an H&K style hook loop on the opposite side from the shell carrier instead of the standard 1 inch sling loop. ADAPTER MOUNT SURESHELL SHOTSHELL CARRIERS #90380 Adapter Mount SureShell Carrier (6-Shell, 12-GA) Traditional on-gun shell holder solutions require alterations to the shotgun. To make things simpler for users of our telescoping stock adapter systems, our first SureShell shotshell carriers were designed to be attached to the side mount points of our High-tube telescoping stock adapters. The push-button sling swivel mounting capability is still retained when a mounting point is used for a SureShell shotshell carrier, and a single telescoping stock adapter can accommodate multiple SureShell shotshell carriers at one time. #90370 Adapter Mount SureShell Carrier (4-Shell, 12-GA) STOCK MOUNT SURESHELL SHOTSHELL CARRIERS BENELLI STOCK MOUNT Our Stock Mount SureShell carriers fit on most Benelli pistol grip fixed stocks. The rugged stamped steel SureShell bracket replaces the stock’s sling loop and mounts four additional shells securely on the side of the stock (does not fit on Benelli M4 stocks, nor will this shell carrier fit on the Urbino Tactical stock). This assembly is also available with an H&K style (dog leash) hook loop opposite the shell carrier instead of the webbing loop. #91840 Stock Mount SureShell Carrier for Benelli M1/M2 (4-Shell, 12-GA) #91830 Stock Mount SureShell Carrier for Benelli Tac Stocks (except Ben M4) (Hook Loop, 4-Shell, 12-GA) www.mesatactical.com19 SURESHELL SHOTSHELL CARRIERS FOR THE URBINO TACTICAL STOCK #90160 SureShell Carrier for Urbino Cheek Riser (4-Shell, 12-GA) (Left Side) Urbino Tactical stocks with cheek risers can accept SureShell carriers secured right on to the cheekpieces themselves. As with our other SureShell products, these shell carriers feature all aluminum construction. M4 SOPMOD BUTTSTOCK MOUNT SURESHELL SHOTSHELL CARRIERS SureShell carriers are also available for the M4 SOPMOD buttstocks (the kind that we supply with our telescoping stock kits). Offered in four- and six-shell versions, these fit securely to standard M4 SOPMOD style stocks from Mesa Tactical as well as other suppliers. Though designed to be installed on the right side of the buttstock, they can be inverted and installed on the left side if necessary. 20 Mesa Tactical Catalog #18 #93340 SureShell Carrier for M4 SOPMOD Stock (4-Shell, 12GA) (Right Side) BARREL AND MAGAZINE CLAMPS Mesa Tactical Magazine and Barrel Clamps provide mounting points for Picatinny rails, weapon lights and sling attachments near the muzzle of a tactical shotgun. Both designs are #92690 Barrel Clamp w/ Rail for CNC machined 6061-T6 aluminum, Type III anodMoss 930 (12-GA) ized to military specifications. Threaded attachment points feature Timesert steel thread inserts for long thread life, even after repeated mounting and removal of accessories. The Mesa Tactical Magazine Clamp can be used to more securely retain aftermarket or factory magazine extensions, while at the same time offering flexible accessory mounting options near the shotgun muzzle. Magazine clamps are available with #90810 a push-button quick release sling swivel or a Magazine Clamp with Rail for two inch MIL-STD-1913 (NATO STANAG Rem 870 (weapon light not included) 4694) Picatinny rail that can accept standard weapon light mounts. The Magazine Clamp can also be used to mount one inch diameter weapon lights simply by clamping one side to the shotgun barrel and the other side to the light body (recommended for use with shotguns with tall front sight posts). #90650 Magazine Clamp with Sling Our Barrel Clamp offers an accessory Swivel for Rem 870 mount point for shotguns that do not have extended magazines. Its unique clamping mechanism ensures a secure fit even under recoil. Mesa Tactical Magazine and Barrel Clamps can accept accessories made for Mesa Tactical Stock Adapters, including Mesa Tactical Adapter Mount Rails (see page 24). BARREL AND MAGAZINE CLAMPS Part # 90800 90650 90700 90810 92660 92670 92680 92690 Item Magazine Clamp Magazine Clamp Barrel Clamp Magazine Clamp Magazine Clamp Magazine Clamp Magazine Clamp Barrel Clamp Platform Caliber Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Mossberg 930 Mossberg 930 Mossberg 930 Mossberg 930 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA Rail Sling Swivel Yes Yes Yes Yes Yes Yes Clamp Type Pkg. Weight License MSRP Magazine Magazine Barrel Magazine Magazine Magazine Magazine Barrel 3 oz 4 oz 3 oz 4 oz 3 oz 4 oz 4 oz 3 oz NLR NLR NLR NLR NLR NLR NLR NLR $65.00 75.00 90.00 90.00 65.00 75.00 90.00 90.00 www.mesatactical.com21 PICATINNY RAILS Mesa Tactical has long been a supplier of MIL-STD-1913 (NATO STANAG 4694) Picatinny rails for tactical shot#90770 Picatinny Rail for Moss guns. A Picatinny rail for the mount500/590 (Standard Profile, 4½ inch) ing of sighting optics is included with every Mesa Tactical High-tube Telescoping Stock Adapter Kit. Additional Picatinny rails are also available for the mounting of optics and accessories, such as lights and lasers. Adapter-mount rails are designed to be attached to telescoping stock adapter accessory mount points, requiring no alterations to the shotgun. These are also compatible with Mesa Tactical Barrel Clamps and Magazine clamps (see page 21). Receiver-mount rails are made to be mounted onto the receivers of Remington, Mossberg, and Benelli shotguns with pre-drilled and tapped mounting holes. These rails can also be used with weapons that are custom drilled and tapped. All Mesa Tactical Picatinny rails are machined from 6061-T6 aircraft quality aluminum, and finished with Mil-spec Type III hard anodizing. Mesa Tactical Picatinny rails include all necessary mounting hardware. RECEIVER MOUNT PICATINNY RAILS Mesa Tactical provides two methods for mounting Picatinny rails to tactical shotguns. For Remington shotguns, we offer the Mesa Tactical Saddle Rail, which mounts to both side of the receiver and wraps around the top. Top mount rails work with Remington, Mossberg and Benelli shotguns that feature factory tapped rail mounting holes in the top of the receiver. REMINGTON SADDLE RAILS Mesa Tactical Saddle Rails are 6061-T6 aluminum brackets that wrap around the top of the shotgun receiver. The factory trigger pins are replaced by an internally threaded steel pin (in the #91680 rear) and paired ChiSaddle Rail for Remington w/ Magazine Clamp cago screws (up front), (12-GA, 20 inch) to which both sides of the saddle rail are securely bolted. The saddle rail is Type III anodized for a rugged surface finish. Our Saddle Rail is specially contoured to allow operation of a semi-automatic bolt on the right side of the receiver, so it can be installed on Remington 1100 and Remington 11-87 semi-auto shotguns as well as Remington 870 pump shotguns. The rail is notched at the rear to accommodate Scattergun/Wilson style ghost ring sights, and extends to the front of the shot22 Mesa Tactical Catalog #18 gun receiver (5-inch rail), 2¾ inches past the front of the receiver (8½-inch rail), or just beyond the barrel’s magazine lug (20-inch rail). The 20-inch rails are available with or without the required Magazine Clamp or Barrel Clamp. No gunsmithing is required to install. Minor fitting of fasteners may be necessary. See page 15 for SureShell Saddle Rails that feature a four-, six- or eight-shot SureShell shotshell carrier yoke on the left side of the receiver. REMINGTON SIDE MOUNT RAIL Recently Mesa Tactical was asked by several law enforcement agencies to produce a Picatinny rail that can be mounted on the right side of the Remington 870 and allow a weapon light to be secured behind the ejection port. This is for door breachers who need more light in tight quarters where lights near the muzzle would be unsuitable. We also offer a rail for the left side of the receiver. These rails are compatible with SureShell carriers mounted on the opposite side of the receiver. As with all our rails, these are is machined to the MIL-STD 1913 specification from 6061-T6 aluminum, and features a mounting system similar to that of our SureShell shotshell carriers. RAILS FOR DRILLED AND TAPPED RECEIVERS #92150 Side Mount Picatinny Rail for Remington 870 (right side) (weapon light not included) #92390 Aluminum Picatinny Rail for Benelli M2 Tactical Mesa Tactical makes Picatinny optics rails for several popular shotgun models that feature pre-drilled and tapped holes in the tops of their receivers. Top rails for the Remington 870 use the tactical hole pattern introduced on some tactical 870 models in the summer of 2007. Mossberg rails attach directly to the receivers of late-model (1997 and later) Mossberg pump shotguns with pre-tapped holes. Standard profile Mossberg rails are for general purpose optics mounting applications. Tall profile rails are only for use with Mesa Tactical High-tube telescoping stock adapters, as an alternative to adapter mount rails. Receiver mount rails allow easy access to the Mossberg safety switch. The hardware included with the Remington and Mossberg rails are for pump action shotguns. They can be used with semi-auto versions (Remington 1100 and Remington 11-87, or Mossberg 930) by grinding the fasteners down to the appropriate lengths. Rails for the Benelli M2 Tactical and Benelli SuperNova Tactical mount just forward of the ghost ring sights, extending to the front of the receiver. Benelli M2 Tactical rails can also be installed on round-top Benelli M1 receivers after drilling and tapping the top of the shotgun receiver with #8-40 threads. Consult a gunsmith. www.mesatactical.com23 The Picatinny optics rail for the Kel-Tec KSG features small aluminum flanges on either side of the main rail can accept additional lengths of Picatinny rail to support weapon lights or targeting lasers (rail not included, see immediately below). A pair of unique steel recoil blocks featuring angled set screws ensure the rail assembly is securely mounted to the shotgun. #93540 Picatinny Rail for Moss 500 w/ Pic Rail Clamp (12-GA, 20 in) ADAPTER MOUNT PICATINNY RAILS Adapter Mount Picatinny Rails fasten to the accessory mount points on the sides of Mesa Tactical High-tube telescoping stock adapters, not on the shotgun receiver. They can also be used on the sides of our Barrel #91130 Adapter Mount Standard Clamps, Magazine Clamps and clamps used as front Profile Picatinny Rail, 3-1/2” mount points for 20-inch and 24-inch rails, which feature the same mounting hole pattern as our stock adapters, or our Picatinny rails for the Kel-Tec KSG shotgun. Standard profile rails like the Stubby adhere to the minimum height requirement of the MIL-STD-1913 (NATO STANAG 4694) specification, and should not be used for mounting optics with the High-tube telescoping stock adapters. Tall profile rails are designed to mount optics for use with High-tube telescoping stock adapters, or to mount accessories slightly away from the receiver when fastened to the telescoping stock adapter side accessory mount points. When used for optics, the elevation of the tall profile rails is similar to that of a flat top AR-15. #90470 Adapter Saddle Mount Pic Rail Rail w/ QD Swivel Clamp for Moss 500 (12-GA, 24 in) 24 Mesa Tactical Catalog #18 PICATINNY RAILS Part # Item 90690 91130 91120 91110 Rail Rail Rail Rail Rail-Tall Profile Rail Rail Rail Rail Rail Rail Rail Rail Rail Rail Rail Rail Side Mount Rail Side Mount Rail Rail Rail Rail Rail Rail Rail Rail 90400 90460 90470 90440 90010 90020 92370 92380 91620 91670 90990 90980 91680 92150 92350 90770 90760 93540 93550 92390 92400 94500 Platform Length Mount 2 in 3½ in 5½ in 7½ in Adapter, Clamp Adapter, Clamp Adapter, Clamp Adapter, Clamp Location Caliber Clamp Weight Export MSRP 1 oz 2 oz 2 oz 3 oz NLR NLR NLR NLR $25.00 30.00 35.00 40.00 12 GA 5 oz NLR 50.00 12 GA Pic Rail 12 GA Swivel 12 GA None 12 GA Barrel 12 GA Magazine 12 GA 12 GA 12 GA 12 GA 12 GA None 12 GA Barrel 12 GA Magazine 23 oz 23 oz 21 oz 23 oz 24 oz 2 oz 3 oz 8 oz 10 oz 20 oz 21 oz 22 oz NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR NLR 215.00 215.00 145.00 200.00 200.00 35.00 50.00 85.00 100.00 145.00 200.00 200.00 9 in High-tube Top Moss 500/590 Moss 500/590 Rem 870 Rem 870 Rem 870 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 Rem 870/1100/11-87 24 in 24 in 24 in 24 in 24 in 5 in 8½ in 5 in 8½ in 20 in 20 in 20 in High-tube High-tube High-tube High-tube High-tube Receiver Receiver Receiver Receiver Receiver Receiver Receiver Top Top Top Top Top Top Top Saddle Saddle Saddle Saddle Saddle Rem 870 6 in Receiver Right Side 12 GA 3 oz NLR 60.00 Rem 870/1100/11-87 2½ in Receiver Left Side 12 GA 4 oz NLR 60.00 Moss 500/590 Moss 500/590 Moss 500/590 Moss 500/590 Benelli M2 Ben SuperNova Kel-Tec KSG* 4½ in 4½ in 20 in 20 in 4½ in 5½ in 13 In Receiver Receiver Receiver Receiver Receiver Receiver Receiver Top Top Top Top Top Top Top 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA 2 oz 3 oz 23 oz 23 oz 2 oz 3 oz 23 oz NLR NLR NLR NLR NLR NLR NLR 40.00 45.00 215.00 215.00 45.00 45.00 170.00 Pic Rail Swivel * For Kel-Tec KSG with 18 inch barrel. #90020 Adapter Saddle Mount Pic Rail Rail w/ Magazine Clamp for Rem (12-GA, 24 in) www.mesatactical.com25 HOOK LOOPS MAGAZINE EXTENSION HOOK LOOPS Some shotgun magazine extensions include stamped steel sling plates secured in place by retaining clips. We have produced replacement stampings that feature a circular hook loop instead of the sling loop for use with increasingly popular H&K style (dog leash) sling hooks. Our Magazine Extension Hook Loops are #90730 Ambi Hook Loop available for the Benelli M2 and Benelli M4 for Magazine shotguns, as well as Vang Comp magazine exExtension (Vang Comp, 12-GA) tensions for Remington shotguns (before you ask, the Scattergun/Wilson Combat sling loops are permanently installed and cannot be replaced with hook loops). Magazine Extension Hook Loops feature a tough Mil-spec manganese phosphate finish. Ambi style sling attachments feature mounts on both sides of the receiver. Special retainer clip pliers are required for installation! REAR HOOK LOOPS FOR BENELLI TACTICAL #91410 STOCKS Rear Hook Loop for Factory tactical stocks for most Benelli shotguns include a stamped steel sling plate in the center of the stock. We have produced a replacement stamping that features a circular hook loop instead of the sling loop for use with H&K style (dog leash) sling hooks. Our Rear Hook Loop fits all Benelli platforms except the Benelli M4 (in which the sling plate is actually glued in place), and features a tough Mil-spec manganese phosphate finish. Benelli Tactical Stocks (except Benelli M4) HOOK LOOPS Part # 90670 90730 90750 90790 90820 91270 91410 91190 26 Item Magazine Extension Hook Loop Magazine Extension Hook Loop Magazine Extension Hook Loop Magazine Extension Hook Loop Magazine Extension Hook Loop Magazine Extension Hook Loop Rear Hook Loop for Ben Tac Stocks (except Ben M4) Push Button Sling Swivel for 1-1/4 in Webbing Platform Caliber Rem Vang Comp Rem Vang Comp Benelli M2 Benelli M2 Benelli M4 Benelli M4 12 GA 12 GA 12 GA 12 GA 12 GA 12 GA Ambidextrous Yes Yes Yes Benelli (Not M4) Mesa Tactical Catalog #18 Sling Style Weight Export MSRP H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook H&K Hook 1 oz 3 oz 1 oz 3 oz 1 oz 3 oz NLR NLR NLR NLR NLR NLR $10.00 10.00 10.00 10.00 10.00 10.00 H&K Hook 1 oz NLR 10.00 Push Button 1 oz License 12.00 CREDITS Photography: Caleb Coppola Photography, Los Angeles, CA; MSL International Enterprises, Redondo Beach, CA; R.D. Design, Rancho Santa Margarita, CA; Vision Photodesign, Temecula, CA Design and layout: Thom Barrie Graphics, Bellingham, WA Printing: Printwell, Huntington Beach, CA www.mesatactical.com27 1135 Baker Street Costa Mesa, CA 92626
