service manual facsimile model fo-5500

Transcription

FO-5500U/C
SERVICE MANUAL
No. 00ZFO5500USME
FACSIMILE
MODEL
FO-5500
This service manual FO-5500U/C is applied to the optional type (FO-45UC) equipped with the 3rd transport unit of FO6500U/C. The performance and operation are not different from the old ones. Since only the areas which are changed
from those of FO-6500U/C are described, use the existing service manual (00ZFO6500USME) of FO-6500U/C together
for the other areas.
CAUTION
This laser printer is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard. This means
that this machine does not produce a hazardous laser radiation. The use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eyes retina, there is
danger of spot damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not an individual part.
2) Do not look into the machine with the main switch turned on after removing the toner/developer unit and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing
the optical system.
4) The cover of Laser Printer Unit contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
Laser Wave Length
: 770-810 mm
Laser Pulse Times
: 49.2 µs
Laser Output Power
: 0.5 mW
Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
FO-5500U/C
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
[3] Transmittable Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
[4] Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
[5] Quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
CHAPTER 2. ADJUSTMENTS
[1] Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[2] Diagnostics and service soft switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
[3] Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
[4] Error code table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
CHAPTER 4. DIAGRAMS
[1] Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[2] Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
[3] Point to point diagram and connector signal name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
[1] Control PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[2] TEL/LIU PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
[3] Power supply PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
[4] Operation panel PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
[5] CCD PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21
[6] RS232C I/F PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
[7] Printer control PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
PARTS GUIDE
Note: Since the following contents are the same as those of the base model FO-6500U/C, refer to the Service
Manual for the base model FO-6500U/C.
CONTENTS
CHAPTER 3. MECHANICAL DESCRIPTION
[1] Mechanical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[2] Printer description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
[3] Disassembly/assembly procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Circuit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[2] Circuit description of control PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[3] Circuit description of TEL/LIU PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
[4] Circuit description of CCD PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
[5] Circuit description of operation PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
[6] Circuit description of power supply PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
[7] Circuit description of RS232C I/F PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
CHAPTER 7. OPERATION FLOWCHART
[1] Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[2] Power on sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
CHAPTER 8. OTHERS
[1] Service Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[2] IC signal name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
FO-5500U/C
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications
•
GENERAL
Effective scanning width:
10.1" (256 mm)
Effective recording width:
8.0" (203 mm)
Copy function:
Single/Multi-copy/Sort-copy
(99 copies/page)
Telephone function:
Standard (cannot be used if power
fails)
Applicable telephone
line:
Public switched telephone network/PBX
Compatibility:
ITU-T (CCITT) G3 mode
Configuration:
Half-duplex, desktop transceiver
Compression scheme:
MH, MR, MMR and Sharp special mode
Memory size*:
1 MB (approx. 50 average pages)
Halftone (gray scale):
64 levels
Memory option:
1 MB/2 MB/4 MB Flash Memory
Power requirements:
120 V AC, 60 Hz
Flat-bed, solid-state CCD
Operating environment:
50-86°F (10-30°C), 20 to 85% RH
Horizontal:
Power consumption:
Stand-by: 10 W at AC 120 V
Scanning method:
Resolution:
Maximum: 400 W at AC 120 V
203 lines/inch (8 dots/mm)
Dimensions:
Vertical:
Depth: 22.9" (582 mm)
Standard – 98 lines/inch (3.85
lines/mm)
Height: 13.7" (349 mm)
Weight:
Fine/Halftone – 196 lines/inch (7.7
lines/mm)
Super fine – 392 lines/inch (15.4
lines/mm)
Printing density:
•
Horizontal:
406 lines/inch (16 lines/mm)
391 lines/inch (15.4 lines/mm)
Auto/Manual switching
Modem speed:
14400 bps with automatic fallback to
12000, 9600, 7200, 4800, or 2400 bps
Transmission time*:
Type:
Desktop, Laser Beam Printer
Print system:
Electrostatic Dry Powdered Imaging
System
Exposure system:
Laser Diode + Polygon Mirror
Scanning
Resolution:
Horizontal: 406 (dot/inch)
Vertical: 391 (dot/inch)
Approx. 6 seconds
(Sharp special mode)
Input document size:
Automatic feeding:
Width – 5.8 to 10.1" (148 to 256 mm)
Print speed:
6 pages per minute (A4 size paper)
First print time:
Within 19 seconds (face down)
Warming-up time:
Within 40 sec.
Operating environment:
Temperature: 10-30˚C
Humidity: 20-80%RH
Length – 5.0 to 14.3" (128 to 364 mm)
Manual feeding:
Width – 5.8 to 11.0" (148 to 280 mm)
Length – 5.0 to 17.0" (128 to 432 mm)
Paper size:
Approx. 40.8 lbs. (18.5 kg)
PRINTER SECTION
Vertical:
Reception modes:
Width: 13.8" (351 mm)
Toner cartridge life:
3,000 prints or more (when black-towhite ratio on print is 5% or less)
Drum cartridge life:
20,000 prints or more (when blackto-white ratio on print is 5% or less)
Width – 8.5" (216 mm)
Length – 11-14" (280-356 mm)
Paper capacity:
650 sheets
Automatic document
feeder:
50 documents max.
* Based on ITU-T (CCITT) Test Chart #1 at standard resolution in
Sharp special mode, excluding time for protocol signals (i.e., ITUT phase C time only).
<IMPORTANT PLEASE READ FIRST>
To avoid problems with supplies, please don’t use supplies from other units. Please use new supplies, when supply changes are required.
1–1
FO-5500U/C
[2] Operation panel (1)
CHANGEOVER key
Two types of information appear in the display: prompts related to
operations you are performing, and information about how the fax
is using the telephone line (transmitting, receiving, etc.). Press this
key to switch between the two types of information.
LINE STATUS light
This lights when the fax machine
is using the telephone line.
Display
This displays various
messages during
operation and
programming.
LINE-STATUS
IN USE
Service indicator
This lights when a
problem occurs which
must be fixed by a
service engineer.
Drum cartridge indicator
This blinks when the drum
cartridge nears the end of
its life, and lights steadily
when the drum cartridge
needs replacement.
RESOLUTION
STANDARD
FINE
SUPER FINE
HALF TONE
CHANGEOVER
RESOLUTION key
Press this key to
adjust the resolution
before sending or
copying a document.
Toner cartridge indicator
This blinks when toner nears
empty, and lights steadily
when the toner/developer
cartridge needs replacement.
Paper out indicator
This blinks when one of the
paper sources (cassette) is out
of paper, and lights steadily when
all sources are out of paper.
FUNCTION key
SPEED DIAL key
Press this key to dial Press this key to select
a Speed Dial number. various special functions.
BROADCAST key
Press this key to send a
document to a group of
receiving fax machines.
Telephone dial keypad
(numeric keys)
Use these keys to dial
and program numbers.
REPORT key
Press this key to print out
a report on the transaction
just completed.
COPY key
Press this key to make
a copy of a document.
ABC
1
GHI
MNO
5
COPY
REPORT
DOCUMENT
SPEED DIAL
BROADCAST COVER SHEET PRIORITY
6
TUV
7
FUNCTION
3
JKL
4
PRS
DEF
2
DOCUMENT key
Press this key to transmit
a document without
reading it into memory.
WXY
8
REDIAL
9
OPER
SPEAKER
STOP
START
0
REDIAL key
Press this key to automatically
redial the last number dialed.
SPEAKER key
Press this key to dial a
number without picking
up the handset.
STOP key
Press this key to
stop operations
before they are
completed.
COVER SHEET key
Press this key to include
a cover sheet with a
transmitted document.
1–2
START key
Press this key to
send or receive
a document.
PRIORITY key
Press this key when
you want to transmit
a document ahead of
other documents which
are waiting in memory
for transmission.
FO-5500U/C
Operation panel (2)
RELAY key
Press this key to send a document
to another fax machine and have
that machine in turn send the
document to a number of end
receiving machines.
PAGE COUNTER key
Press this key to have a slash and
the total number of pages added
after each page number on the
pages of a transmitted document.
Rapid Dial keys
Press one of these keys to dial a fax
or voice number automatically. (these
keys also serve as letter entry keys
when storing a name).
TIMER key
Press this key to set an
operation to be performed
automatically at a later time.
LIFE key
Press this key, followed
by the "1" key, to check
the total number of pages
printed by the fax machine.
CONFIDENTIAL key
Press this key to send or
print out a confidential
document.
CONTRAST key
Press this key to adjust the
contrast before sending or
copying a document.
MEM. STATUS key
Press this key to
see what documents
have been scanned
into memory for
transmission.
01
02
03
04
05
06
07
08
33
34
35
36
37
38
39
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
09
10
11
12
13
14
15
16
41
42
43
44
45
46
47
48
J
K
L
M
N
O
P
I
J
K
L
M
N
O
P
I
17
18
19
20
21
22
23
24
CONTRAST PAGE COUNTERCONFIDENTIAL TIMER
RELAY
Q
U
Q
R
S
T
U
V
W
X
25
26
27
28
29
30
31
32
Y
Z
SHIFT
SP
CLEAR
CLEAR key
Press this key to clear
mistakes when storing
names and numbers.
SP key
Press this key to enter
symbols when storing
a name.
SHIFT key
Press this key to switch
between upper and
lower case when storing
a name.
T
V
key, key
Press these keys to move
the cursor forward and
backward when storing
names and numbers.
1–3
MEM.STATUS SEARCH DIAL
W
DOWN
X
UP
Z
SPACE
(Flip up the
Rapid Key
overlay)
SPACE key
Press this key to enter a
space when storing a name.
S
DUPLEX SCAN
Y
SPACE
R
LIFE
40
SHIFT
SP
CLEAR
DUPLEX SCAN key
Press this key to transmit
or copy two-sided
documents.
UP and DOWN key
Press these keys to adjust
the volume of the handset
when the handset is lifted,
the volume of the speaker
when the SPEAKER key
has been pressed, or the
volume of the ringer at all
other times.
SEARCH DIAL key
Press this key to
search by name for
a number stored
for automatic
dialing.
FO-5500U/C
4. Cautions on Transmitting Documents
• Documents written in yellow, greenish yellow, or
[3] Transmittable documents
Normal size
width
5.83" – 8.5" (148 – 216 mm)
length
5.04" – 11" (128 – 279 mm)
(Max.)
432mm
(Max.)
Letter size 279mm
(Min.)
•
Ink, glue, and correcting fluid on documents must be dry before the
documents can be transmitted.
•
All clips, staples and pins must be removed from documents before transmission.
•
Patched (taped) documents should be copied first on a copier and
then the copies used for transmission.
•
All documents should be fanned before insertion into the feeder to
prevent possible double feeds.
5. Automatic Document Feeder Capacity
128mm
148mm
216mm
[Normal size]
Number of pages that can be placed into the feeder at anytime is as
follows:
216mm
[Special size]
Normal size: max. 50 sheets (14 lbs – 20 lbs)
Use document carrier sheet for smaller documents.
*
Special size: single sheet only (manual feed)
With special sizes, only one sheet can be fed into the machine at
a time. Insert next page into feeder as current page is being
scanned.
NOTES:
2. Paper Thickness & Weight
Product specifications
Indication
Weight
indication
Thickness
indication
Lower Limit
Upper Limit
Japanese indication
Size 4 × 6
45kg paper
70kg paper
Metric system
indication
52g/m2
80g/m2
American indication
LB system indication
14 LB
20 LB
Metric system
indication
0.06mm
0.1mm
Inch system indication 0.0024"
Document
size
light blue ink
cannot be transmitted.
1. Document Sizes
Document size
Range
•
When you need to send or copy more pages than the
feeder limit, place additional pages in feeder when last
page in feeder is being scanned.
•
Place additional pages carefully and gently in feeder.
If force is used, double-feeding or a document jam may
result.
6. Readable Width & Length
The readable width and length of a document are slightly smaller than
the actual document size.
Note that characters or graphics outside the effective document scanning range will not be read.
•
Readable width
8.3" (208 mm) max.
0.0035"
(148mm × 128mm) ~
W letter (279.4mm × 432mm)
A4 (210mm × 297mm)
Letter (216mm × 279mm)
Number of Document size
ADF sheets Weight
Paper
quality
Kind
B6 ~ Letter/A4 size
50 sheets
B4 size/Legal
20 sheets
W letter size
1 sheet
90 kg (104g/m2) or more
135 kg (157g/m2) or less
1 sheet
Readable width
•
Paper of fine quality/bond paper/Kent
paper
4mm
3. Document Types
• Normal paper
Documents handwritten in pencil (No. 2 lead or softer), fountain
pen, ball point pen, or felt-tipped pen can be transmitted.
Documents of normal contrast duplicated by a copying machine
can also be transmitted.
•
Diazo copy (blueprint)
Diazo copy documents of a normal contrast may be transmitted.
•
Carbon copy
A carbon copy may be transmitted if its contrast is normal.
Readable length
This is the length of the document sent minus 0.16" (4 mm) from the
top and bottom edges.
Readable length
4mm
1–4
FO-5500U/C
7. Use of Document Carrier Sheet
TELEPHONE JACK
A document carrier sheet must be used for the following documents.
A standard RJ11C telephone jack must be located near the machine.
This is the telephone jack commonly used in most homes and offices.
•
•
•
Those with tears.
•
Those smaller than size 5.83" (W) × 5.04" (L) (148 mm (W) × 128
mm (L)).
Carbon-backed documents
If the machine is moved from a cold to a warm place...
If the machine is moved from a cold to a warm place, it is possible
that the reading glass may fog up, preventing proper scanning of
documents for transmission. To remove the fog, turn on the power
and wait approximately 2 hours before using the machine.
Make print straight
across paper
E.G.
Place the document
carrier in the document
feeder with the clear film
side down
2. Installing the printer cartridges (Toner
cartridge: FO-45ND/Drum cartridge: FO-45DR)
1 Press the button on the side of the printer compartment, and open
Direction of insertion
the printer cover.
NOTE: To transmit a carbon-backed document, insert a white
sheet of paper between the carbon back of the document
and the document carrier.
•
Those containing an easily separable writing substance (e.g., tracing paper written on with a soft, heavy lead pencil).
NOTES:
•
•
When using the document carrier, carefully read the instructions written on the back.
•
If the document carrier is dirty, clean it with a soft, moist
cloth, and then dry it before using for transmission.
•
Do not place more than one document in the carrier at a
time.
Plugging the fax machine into a jack which is not an RJ11C jack
may result in damage to the machine or your telephone system. If
you do not know what kind of jack you have, or need to have one
installed, contact the telephone company.
•
Caution! The ribs on the bottom of the inside of the printer
cover become very hot during printing. Be careful not to touch
them.
•
If you are installing the cartridges for the first time, go to Step 4.
The thickness of document which can be held with the carrier
sheet is up to 20 lb.
2 If you are replacing the cartridges, grasp the handle on the toner
cartridge, and pull the toner cartridge out of the compartment.
[4] Installation
•
If you are only replacing the drum cartridge, place the toner
cartridge on a piece of paper on a horizontal surface.
•
If you are only replacing the toner cartridge, go to Step 6.
1. Site selection
Take the following points into consideration when selecting a site for
this model.
ENVIRONMENT
•
•
The machine must be installed on a level surface.
•
Provide easy access to the front, back, and sides of the machine.
In particular, keep the area in front of the machine clear, or the
original document may jam as it comes out after scanning.
•
•
The temperature should be between 41° and 95°F (10° and 35°C).
Keep the machine away from air conditioners, heaters, direct sunlight, and dust.
The humidity should be between 30% and 85% (without condensation).
3 Pull the old drum cartridge out of the compartment.
ELECTRICITY
A 120 V, 60 Hz, grounded (3-prong) AC outlet is required.
Caution!
•
Connection to a power source other than that specified will cause
damage to the equipment and is not covered under the warranty.
•
If your area experiences a high incidence of lightning or power
surges, we recommend that you install a surge protector for the
power and telephone lines. Surge protectors can be purchased at
most telephone specialty stores.
1–5
FO-5500U/C
4 Remove the new drum cartridge from its packaging.
9 If you replaced the toner cartridge, reset the toner counter by
pressing the LIFE key (flip up the Rapid Key overlay if necessary),
the "2" key, and the START key.
LIFE
right side is marked "R") with the arrowhead pointing down which
is marked on the right side of the compartment, and insert the
cartridge into the compartment so that the ends of the cartridge
move along the guides on the sides of the compartment. Make
sure the cartridge is set firmly in place.
•
2
V
5 Align the arrowhead on the right side of the drum cartridge (the
•
START
F If you replaced the drum cartridge, reset the drum counter by
pressing the LIFE key (flip up the Rapid Key overlay if necessary),
the "3" key, and the START key.
Place the old drum cartridge (if you removed one) in the empty
drum cartridge bag, seal the bag, and dispose of it in a way that
conforms to any local regulations that may exist in your area.
LIFE
If you are not replacing the toner cartridge, go to Step 7.
START
3
V
L
R1
Left
Right
3. Assembly and connections
1 Connect the handset cord to the handset and the fax as shown.
•
6 Remove the new toner cartridge from its packing, and shake sev-
Place the handset on the handset rest.
eral times as shown.
•
This ensures that the toner is well distributed inside the cartridge.
7 Hold the handle of the toner cartridge so that the "2" marked on
Use the handset to make ordinary
phone calls, or to transmit and receive documents manually.
the cartridge is to the right, and insert the cartridge into the compartment so that the two knobs on each side of the cartridge move
along the two guides on each side of the compartment.
Press the handle down so that the cartridge sets into place.
•
The ends of the handset cord are identical, so they will go into
either jack.
2 Plug one end of the telephone line cord into the jack on the fax
marked "LINE". Plug the other end into a standard (RJ11C) telephone wall jack.
Place the old toner cartridge (if you removed one) in the empty
toner cartridge bag, seal the bag, and dispose of it in a way that
conforms to any local regulations that may exist in your area.
2
Left
Right
8 Close the printer cover.
TEL.
LINE
1–6
FO-5500U/C
3 Plug the power cord into a 120V, 60Hz, grounded (3-prong) AC
6 Insert the male end of the PC interface cable into the port on the
outlet.
right side of fax as shown. Tighten the attached screws with a
screwdriver.
Press the power switch to turn on the power.
7 Insert the female end of the PC interface cable into the serial
4 Attach the original document OUT tray by inserting the tabs into
(RS-232C) port on your computer.
Tighten the attached screws with a screwdriver.
the holes in the fax as shown.
5 Attach the received document tray by inserting the tabs into the
holes in the fax as shown.
4. Loading printing paper
The paper cassettes and the paper tray hold the paper on which
received documents are printed. If needed, a second cassette is
available as an option from your dealer.
The paper cassette can hold 500 sheets of either legal or letter size
paper. The paper tray can hold 150 sheets of either legal or letter size
paper.
1 Grasp the hand hold on the cassette as shown, lift the cassette
slightly, and then pull it out as far as it will go. Do not force.
Push down on green levers on both sides of the cassette tray as
shown, and then pull it completely out of the fax using both hands.
1–7
FO-5500U/C
2 Pinch the ends of the paper guide together, and move the guide to
7 Move the paper guide to the appropriate position depending on
the appropriate position depending on whether you are loading
letter or legal size paper.
whether you are loading letter or legal paper.
•
To remove the paper guide, press its inner side at the arrow
marks and lift.
LETTER
LEGAL
LT
R
LG
L
3 Place a stack of paper on the pressure plate, press it down, and
8 Place the paper in the tray.
insert the two far corners of the paper under the paper holders as
shown.
•
Make sure the stack of paper is not higher than the tabs at the
top of the paper guide. If it is, remove some of the paper.
9 Close the original document IN tray.
4 Put the cassette back in the fax.
•
Push down on green levers on sides of cassette for it to go all
the way in.
F If desired, attach a letter or legal sticker as appropriate to the fax
as shown.
5 If desired, attach a letter or legal sticker as appropriate to the
cassette.
6 Rotate the received document tray back. Grasp the hand hold on
the original document IN tray as shown, and open it.
1–8
FO-5500U/C
5 Replace the drum cartridge, and then the toner cartridge.
5. Clearing paper jams
If a document doesn’t feed through the scanner properly during transmission or copying, or DOCUMENT JAM appears in the display, first
try pressing the START key. If the document doesn’t come out of the
feeder, open the operation panel by squeezing the operation panel
release on the right side of the operation panel (marked "PULL UP"),
and gently pull out document.
L
R1
Left
1
Right
2
Left
Right
6 Close the printer cover.
2 If the leading edge of the document is protruding from the printer
compartment outlet, try pulling it out.
•
If you are unable to clear the paper jam in this way, continue
with the following steps.
7 If you didn’t find any paper in the printer compartment, or if
3 Open the printer cover and remove the toner cartridge and drum
cartridge.
PAPER JAM still appears in the display after you close the printer
cover, check each paper cassette and the paper tray.
•
•
Caution! The ribs on the bottom of the inside of the printer
cover become very hot during printing. Be careful not to touch
them.
4 Gently pull the paper out of the compartment.
•
•
To check the paper tray, grasp the hand hold on the original
document IN tray and rotate the tray up.
8 Gently pull out any jammed paper you find, and then replace the
If the leading edge of the paper has entered the fusing unit, first
pull the leading edge out of the fusing unit, then pull the paper
out of the compartment.
cassette or close the original document IN tray.
Be sure to remove any torn pieced of paper.
1–9
FO-5500U/C
6. Installing an option cassette (FO-45UC)
1 Remove the two screws on the rear side of the optional cassette,
and then remove the rear plate of the optional cassette.
2 Place the fax machine on top of the optional cassette. Connect the
connector on the optional cassette to the wire connector on the
bottom of the fax.
3 Replace the rear plate on the optional cassette, and secure it with
the two screws.
4 Secure the optional cassette to the fax machine with two screws
on the front and one screw on each side.
1 – 10
FO-5500U/C
[5] Quick reference guide
FUNCTION key menu
The following chart shows the layout of the functions and settings accessed by pressing the FUNCTION key. First press the FUNCTION key, the
appropriate numeric key as shown, and then "#" or " " until the desired item appears.
Instructions for making each setting appear in the display. If you have any difficulty, refer to the detailed instructions on the page shown below the
setting.
FUNCTION
1
Reception
Mode
4
3
2
Entry Mode
Optional Settings
Activity Report
Fax/Tel
Numbers for
Auto Dialing
Fine Resolution
Priority
Timer List
Telephone
Number List
Passcode Number
Relay Group List
Own Number and
Name Set
Passcode List
Option Setting
Program/Group
List
Batch
Transmission List
Department
Usage List
Date and Time
Set
7
6
Listing Mode
8
Print Hold
Mode
Program/Group
Mode
Retransmission
Times
Hold Data Print
Program Entry
Mode
Number of Rings to
Auto Answer Mode
Retransmission
Interval
Print Hold Code
Set
Auto Listing
Heater Mode
Print Hold Code
Clear
Transaction Report
Print Select
Junk Fax Check
Group Entry
Mode
Alarm Buzzer
Recall Times
Dial Mode
ID Number
Recall Wait Interval
Quick on Line
System Number
Security Selection
Store Junk Fax
Number
ECM
Multi TTI
Beep Length
Auto cover Sheet
Department
Code Mode
Confidential
Reception List
Anti Junk Fax
Number List
Tel. Billing Code
Memory Scanning
Copy Reduce
Department Code
Mode
Copy Cut-off
Distinctive Ringing
Receive Reduce
Verification Stamp
Image Memory
Print
Print Hold
PC-Interface Mode
Cassette Selection
Receive Unit
Cassette
Changeover
Note: Steps which are optional are enclosed in a dotted frame:
RESOLUTION
Transmitting documents
Normal Dialing (1)
Load
document
RESOLUTION
Lift handset
or
press SPEAKER
Dial (press
numeric keys)
START
Wait for
reception tone
Normal Dialing (2)
Lift handset
or
press SPEAKER
Hang up
Load
document
Dial (press
numeric keys)
RESOLUTION
START
Wait for
reception tone
Direct Keypad
Dialing
Hang up
START
Load
document
RESOLUTION
Dial (press
numeric keys)
Load
document
RESOLUTION
Press Rapid
key
Load
document
RESOLUTION
SPEED DIAL
Load
document
RESOLUTION
REDIAL
Rapid Key Dialing
Speed Dialing
Redialing
Enter Speed Dial number
(press numeric keys, -if less
than 3 digits, press START
to complete entry)
START
START
1 – 11
Wait for
reception tone
Serial Polling
Mode
9
Memory Polling
Mode
Memory Polling Set
Memory Polling
Clear
FO-5500U/C
MEMO
1 – 12
FO-5500U/C
CHAPTER 2. ADJUSTMENTS
(1)
F3 (CCP2E20) is installed in order to protect IC’s from and
overcurrent generated in the verification stamp drive circuit. If F3
is open, replace it with a new one.
(2)
F1, F2 (CCP2E30) is installed in order to protect IC’s from an
overcurrent generated in the TX motor drive circuit. If F1, F2 is
open, replace it with a new one.
[1] Adjustments
General
In addition to the replacement of F1, F2 and F3, the factor
causing F1, F2 and F3 to open must also be repaired. If not, F1,
F2 and F3 will open again.
Since the following adjustments and settings are provided for this
model, make adjustments and/or setup as necessary.
Replacement parts
1. Adjustments
CCP2E20 (Sharp code: VHVCCP2E20/-1)
Adjustments of output voltage (FACTORY ONLY)
CCP2E30 (Sharp code: VHVCCP2E30/-1)
1. Install the power supply unit in the machine.
3. Volume adjustment
2. Set the recording paper and document.
You can adjust the volume of the speaker, handset, and ringer using
the UP and DOWN keys on the operation panel (flip up the Rapid Key
overlay to access the keys).
Speaker
The speaker has 3 volume levels: HIGH, MIDDLE, and LOW. To
adjust the volume of the speaker, press the SPEAKER key and then
press the UP or DOWN key until the desired level appears in the
display. Press the SPEAKER key again to turn the speaker off.
Handset
The handset receiver has 3 volume levels: HIGH, MIDDLE, and LOW.
To adjust the volume of the handset receiver, lift the handset and
then press the UP or DOWN key until the desired level appears in the
display.
Ringer
The ringer has 4 volume levels: HIGH, MIDDLE, LOW, and OFF. To
adjust the volume of the ringer, press the UP or DOWN key until the
desired level appears in the display (make sure the SPEAKER has
not been pressed and the handset is not lifted). The fax will ring at the
new volume level each time you change the level. If you select OFF,
press the START key to confirm your selection.
3. When the document is loaded, power is supplied to the output
lines. Confirm that outputs are within the limits below.
Output voltage settings
POWER SUPPLY
PWB
CNPW
CNPW
CONTROL
PWB
Fig. 1
Output
+5V
+12V
VM (+24V)
Voltage limits
4.75V~5.25V
11.5V~12.5V
23.04V~24.96V
Connector
No.
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
CNPW
4. Settings
VM
VM
VM
MG
MG
MG
+5V
+5V
DG
DG
+12V
AG
(1) Dial mode selector
OPTION SETTING: DIAL MODE (Soft Switch No. SW2 DATA No. 1)
Use this to set the fax machine to the type of telephone line you are
on.
•
The factory setting is "TONE".
(step 1) Select "OPTION SETTING".
KEY:
(step 2) Select "DIAL MODE".
KEY:
2
3
DISPLAY: DIAL MODE
ICPs (IC Protectors) are installed to protect the TX motor drive circuit
and verification stamp drive circuit. ICPs protect various ICs and electronic circuits from an overcurrent condition.
(step 3) Select, using "1" or "2".
KEY:
The location of ICPs are shown below:
CNPW
1
DISPLAY: TONE SELECTED
CNPRT
KEY:
IC17
F1
4
DISPLAY: OPTION SETTING
2. IC protectors replacement
CONTROL
PWB
(TOP SIDE)
FUNCTION
CNRS
2
DISPLAY: PULSE SELECTED
(step 4) End, using the "STOP" key.
CNPN
KEY:
IC13 F2 F3
Fig. 2
2–1
STOP
ENTER #01
33,
,#
Cursor
When initially registering,
the mode shows 1=TONE.
When registering again, the
mode which was registered
formerly is shown.
1=TONE, 2=PULSE
FO-5500U/C
[2] Diagnostics and service soft switch
1. Operating procedure
Two kinds of diagnoses are supported.
1-1. Fax diagnosis
1-2. Print diagnosis
This diagnosis is concerned with the main body of fax which is
used for production and service support.
This diagnosis is concerned with the print which is used for production and service support.
Entering the diagnostic mode
9
Press FUNC
display will appear.
8
Entering the diagnostic mode
9
Press FUNC
display will appear.
7 , and the following
6 , and the following
PCU ROM Ver.:
ROM: XXXXX XXXXX
FAN0
Then press the START key. Select the desired item with
key and the
key or select with the rapid key.
Identical
the
Enter the mode with the START key.
FAN1
Then press the START key. Select the desired item with the
and the
key or select with the rapid key.
Enter the mode with the
(Diag • specifications)
key
START key.
(Diag • specifications)
9
FUNC
8
FUNC
8
7
9
8
6
PCU ROM Ver.:
ROM: FAN0 FAN1
START
START
01
START
AREA PRINT MODE
01
START
SOFT SWITCH MODE
02
START
CHECK PATTERN 1
02
START
PRINT AREA
03
START
CHECK PATTERN 2
03
START
ROM & RAM CHECK
04
START
CHECK PATTERN 3
04
START
AUTO FEEDER MODE
05
START
PAPER FEED AGING
05
START
AGING MODE
06
START
BIAS ADJUST MODE
06
START
PANEL CHECK MODE
07
START
LIFE SET MODE
07
START
OPTICAL ADJUST MODE
08
START
LIFE ALL CLEAR
08
START
PRODUCT CHECK
09
START
LIFE ENTRY MODE
09
START
SIGNAL SEND MODE
10
START
TOP ADJUST MODE
10
START
COMM. CHECK MODE
11
START
LIFE CLEAR MODE
11
START
MEMORY CLEAR
12
START
FLASH MEMORY
13
START
ALL FAX/TEL ENTRY MODE
14
START
RS232C CHECK MODE
15
START
DEPT. PASSCODE
16
START
CONF. PASSCODE
17
START
PRINT HOLD CODE
18
START
MEMORY SET MODE
19
START
MOTOR AGING
20
START
STAMP AGING
21
START
SCANNER SET MODE
22
START
DIAL TEST MODE
23
START
COPY DIAG MODE
3) Memory clear when power is turned on
Pressing the START and STOP keys, turn on the main power, and
the following message will be displayed.
MEMORY CLEAR
EXECUTE ? 1 = YES , 2 = NO
Here, when 1: YES is selected, the memory will be cleared to be
ready for operation.
If 2: NO is selected, it will continue ready for operation as it is.
2–2
FO-5500U/C
•
2. Diagnostic items description
2-1. Fax diagnosis
1) Soft switch mode
•
In this mode, the soft switch are set and the soft switch list is printed.
Soft switch mode screen
Soft switch mode screen
SOFT SWITCH MODE
SW01=00000000
7 Linked
change of data (This is the same even in the optional setting.)
• When the department control function is off, the multi TTI function
8
Switch 1
No.
OFF to ON of department control function during use of image
memory.
(Note: In the existing set, the department control function is set from
OFF to ON when the timer communication (including the batch
sending) or the memory hold is set.)
ON to OFF of continuous serial polling function when the continuous
serial polling is started.
(Note: In the existing set, "ON to OFF of the continuous serial
polling function when the continuous serial polling is registered" has
been applied, but the conditions are now moderated. However, registration is impossible to the program of the new continuous serial
polling when the continuous serial polling function is OFF.)
and telephone billing code function are turned off.
1 Switch
number selection
• Press START key for setting of the next soft switch. If the soft switch
Data
•
2) Print area
According to the size of the specified sheet, the effective printing area is
printed.
number is the final, pressing START key will exit the soft switch
mode.
Enter two digits of a soft switch number to set the switch number. If
a switch number of unexisting soft switch is entered, key error
buzzer sounds to reject the input.
SOFT SWITCH MODE
SW1
SOFT SWITCH MODE
SW01=00000000
1
3) ROM & RAM check
The sum value of ROM, the work and the back-up RAM are checked.
The RS-232C interface is also checked. If any error occurs, the buzzer will
inform it. (Refer to the following table). Finally, the result will be printed.
This diagnosis does not check the flash memory. The flash memory is
checked with the flash memory test.
SOFT SWITCH MODE
SW16=00010110
6
Number of buzzer sounds
2 Data number selection
Device checked
Remarks
1 time <Short sound>
ROM1
Main
The cursor position shows the data to be set.
2 times <Short sounds>
ROM2
Main
Pressing # key moves the cursor to the right. If, however, the cursor is
on data number 8, pressing # key shifts the cursor to data number 1 of
the next switch number. If the switch number is the final, pressing # key
will exit the soft switch mode.
Pressing
key moves the cursor to the left. If, however, the cursor is
on data number 1, pressing
key shifts the cursor to data number 1
of the former switch number. If the switch number is 1, pressing
key
will not move the cursor.
Integrated ROM/RAM
Main
D-RAM
Main
S-RAM
Main
*6 times <Short sounds>
S-RAM (on the optional memory)
Main
1 time <Long sound>
ROM
Sub 1
2 times <Long sounds>
Integrated ROM/RAM
Sub 1
D-RAM
Sub 1
Dual port RAM1
Sub 1
ROM
Sub 2
Integrated ROM/RAM
Sub 2
D-RAM
Sub 2
Dual port RAM2
Sub 2
3 Data
setting method
Press the FUNCTION key, and the data at the position of the cursor
6
will be reversed to 0 when it is 1, or to 1 when it is 0. (If the soft switch
can be changed at the bit (Refer to .), the error buzzer will sound
with the process not received.)
4 Outputting
method of soft switch list
In the soft switch mode, press the REPORT key, and the soft switch list
* As practical, it is judged that the optional memory is not installed if any
will be output.
If the recording paper runs out or is clogged, the key error buzzer will
sound with the process not received.
error occurs. Therefore, it does sometimes not sound.
For the short and long sounds, one pattern is as follows.
Main system: 0.25 seconds ON/0.25 seconds OFF
Sub system: 1.00 second ON/0.25 seconds OFF
The execution state of checking is as follows. Moreover, the list of the
check result is output after checking is ended.
5 Storage
of data
In the following case, the data of the soft switches set will be stored.
•
•
•
•
•
It is shifted to set the next soft switch by pressing the START switch.
It is shifted to set the next soft switch with the [#] key.
It is shifted to set the last soft switch with the [ ] key.
It is shifted to set another soft switch by inputting two digits as the
switch number. (When 2 digits are completely input.)
Output of the soft switch list is started.
Display during check
6 Inhibition
of data change
(This is also applicable for the optional setting.)
Display after check
ROM CPU SRAM DRM DPR
••
PP
•
••
•
P
P=PASS
In the following case, it is inhibited to change the data with the key
error buzzer.
• When the print hold bus code is not registered, the print hold function is turned from OFF to ON.
• When the print hold function is on, the print hold bus code is
cleared.
• When the memory is used because of substitutive receiving, etc, the
print hold function is mutually turned on/off.
• OFF to ON of telephone billing function which is using the image
memory is used (Note: In the existing set, the telephone billing code
function is specified from OFF to ON when the timer system communication (including the batch communication) is set.)
Here, the memory is usable when the telephone billing code function is on. It can be set from ON to OFF while the memory is used.
However, if setting is practically changed even once, it can not be
returned from OFF to ON.
• OFF to ON of multi TTI function and telephone billing code function
when the department control function is OFF.
E
P
ROM/RAM
check list
output
E=ERROR
<Relationship between display and memory>
••
•
••
•
DRAM (4Mbit)
SRAM (512Kbit x 2)
ROM (4Mbit x 2)
• When the option is installed, two SRAMs
are added every option.
(The type without the optional unit is shown.)
The check result of RS-232C interface board is listed and printed together
with the check result of ROM&RAM.
2–3
FO-5500U/C
5 Flash memory test mode (Same as Diagnosis 12)
6 Registration of fixed data
4) Auto feeder mode
The auto feed function can be checked by inserting and discharging
the document.
Registration of rapid key No. and other data necessary for production.
The registered data are shown in the following table. The chain
dial is not set for any destination.
Check of auto feed function
After this mode is activated, set up the document, and press the
START key, and it will be automatically fed. (Before the START key is
pressed, the document sensor alone is activated.)
Moreover, the document size (A4/B4) and sensor information
(A4/B4/ORG) are displayed when the document sensor is turned.
04 : AUTO FEEDER MODE
(
)
After setup of the document
Rapid
No.
FAX
No.
Rapid
No.
FAX
No.
Rapid
No.
FAX
No.
Rapid
No.
FAX
No.
01
20
06
25
11
1
21
01
02
21
07
26
12
2
22
02
03
22
08
27
13
3
23
03
04
23
09
28
14
4
24
04
05
24
10
29
15
5
25
05
7 Transmission check (Same as Diagnosis 10)
The soft switches necessary for production are set.
8 Test result print (two sheets)
04 : AUTO FEEDER MODE
B4 (A4 B4 ORG)
Only the sensor which is
activated (fallen down) is displayed.)
The paper sheet size (A4/B4) is
displayed.
• AUTO FEEDER CHECK LIST
• FLASH MEMORY CHECK LIST
Memory clear printing
Panel test result printing
ROM&RAM test result printing
Check result printing of RS-232C interface board
5) Aging mode
If any document is set up in the first state (when started), copying will
be executed. If it is not set up, "check pattern 1" of the print diagnosis
is output at the intervals of 1 time/60 minutes. (A total of 10 sheets
are output.)
9 Print area printing (one sheet)
6) Panel check mode
9) Signal send mode
This is used to check whether each key is normally operated or not.
According to the key input, LCD is displayed. Moreover, during execution, the document reading lamp is turned on.
After shift to the mode, press the START key, and the signals will be
transmitted in the following sequence.
It can be used to check the modem and so on.
1 When [PANEL CHECK MODE] is displayed, press the [START]
[ 1] No signals
key.
The test will be started. When the test is started, LEDs will sequentially come on (the lighting sequence and speed are separately specified). It can be checked whether all LEDs are all lit or
not.
[ 2] 4800BPS (V27ter)
[ 3] 33600BPS (V. 34)
[ 4] 31200BPS (V. 34)
2 Press any other key except [STOP] key.
[ 5] 28800BPS (V. 34)
At this time, the name of each key will be displayed every push of
the key.
[ 6] 26400BPS (V. 34)
3 Finally press the [STOP] key.
[ 7] 24000BPS (V. 34)
[ 8] 21600BPS (V. 34)
If all keys can be input, the key input "ALL KEY OK!!" will be
displayed when the STOP key is ended.
The screen will be all displayed in black, and the test result will be
printed.
In this test, it is okayed if all the other keys except [STOP] key have
been pressed from start of the test to its end (the [STOP] key is
pressed). If any key is skipped, it will be regarded as "KEY ERROR!!",
and the name of the key not pressed will be printed on the list as the
result. This will complete printing.
Some two keys may be interchanged in the hardware. In this case, it
is necessary to check the display when pressing the key.
[ 9] 19200BPS (V. 34)
[10] 16800BPS (V. 34)
[11] 14400BPS (V. 34)
[12] 12000BPS (V. 34)
[13] 9600BPS (V. 34)
[14] 7200BPS (V. 34)
[15] 4800BPS (V. 34)
[16] 2400BPS (V. 34)
[17] 14400BPS (V. 33)
7) Optical adjust mode
[18] 12000BPS (V. 33)
The document reading lamp is turned on.
[19] 14400BPS (V. 17)
8) Product check
[20] 12000BPS (V. 17)
The diagnosis is used in the production process.
After shift to the mode, the following operations are sequentially executed. At this time, the sensor of read-error can be checked by feeding the B3 document. Set up one short document of B4 size.
[21] 9600BPS (V. 17)
[22] 7200BPS (V. 17)
[23] 9600BPS (V. 29)
1 Memory clear (Same as Diagnosis 11)
2 Panel test (Same as Diagnosis 06)
3 Document feed
4 ROM & RAM test, RS-232C interface board check (Same as the
[24] 7200BPS (V. 29)
[25] 4800BPS (V27ter)
[26] 2400BPS (V27ter)
[27] 300BPS (FLAG)
diagnosis 03)
[28] 2100Hz (CED)
[29] 1100Hz (CNG)
2–4
This content is executed on the
28,800 bps machine alone.
Note: Since 28,800 bps is not
specified, the contents of
the items may be changed.
FO-5500U/C
10) Comm. check mode
14) RS-232C check mode
1 Turn on the line monitor.
2 Set 0 km at the line equivalence.
3 Bring the copy mode into the continuity mode.
4 It is set to shift into the diagnosis mode when the SPEED key
RS-232C interface board is checked.
When the interface board is installed, the result will be printed after
the check.
15) Dept. passcode
alone is pressed.
After the check, it is necessary to be sure to return the aforementioned soft switches into the initial state.
(Clear the memory with the diagnosis.)
The department passcode list is printed.
16) Conf. passcode
The confidential passcode list is printed.
Differing from printing of one box alone soon after registration, the
confidential passcodes of all boxes are printed.
11) Memory clear
Clear the back-up memory to initialize the soft switches.
The flash memory will be initialized. Then, the initialized list be output.
17) Print hold code
The print lockout passcode No. is printed.
12) Flash memory
The flash memory is checked.
The ordinary memories (ROM, SRAM, DRAM) are checked in the
ROM&RAM check process. The write/read test is taken every block to
print the result.
18) Memory set mode
The set and dump list of the memory content is output.
•
The address (8 digits (P) generally including the bank information
is input, and the data of 2 digits is continuously input.
Inputting is done in the hexadecimal mode. The ten-key is used for
0 thru 9, and the alphabetic keys A (RAPID01 thru 06) are used for
A thru F.
•
During data inputting, the address can be moved forward and
backward one byte by one byte with " " and "#". (The address
prior to the address 0 is looped as the maximum address.)
•
The Validity of the address is not checked. Accordingly, writing/reading operations are possible in the address of the memory
not assigned, the address of ROM and so on.
(However, as practical, writing is not done, and the data content
runs short each reading.)
Though writing is possible in the flash memory, a little time is
required.
It is also necessary to take care that the life of the flash memory is
excessively shortened if much data is written in the flash memory.
Since it may run away depending the written content, take minute
care for the writing address.
•
When the REPORT key is input, the memory dump list is produced
from the displayed address (here, it is limited at the 16-byte boundary address (address with end 0) which does not exceed the specified address and is just in front.). The dump list is output to a
maximum of 99 pages. If any data of one page can be repeatedly
developed and printed, the list is sufficient. But it is not desired that
the content of plural pages are developed in the memory once and
are then printed. If the STOP key is pressed, it will pass to the
diagnosis after the page which is now being printed is completed
printed.
If the address exceeds the maximum address, it will return to the
address 0 and printing will be continued.
When an error occurs, the following error buzzer will sound.
Number of buzzer sounds
Check device
Page memory
Flash memory
Flash memory (optional)
During operation of this diagnosis, dual operation is not possible at
all.
If this is excessively repeated, it will shorten the life of the flash
memory.
13) All FAX/TEL. entry mode
Before entry into the diagnosis, the reference destination number is
first written into the Rapid key number 01 in the FAX number registration mode.
1 The diagnosis mode is activated. If any number is not registered in
the Rapid key number 01 or any program or group is registered,
the diagnosis will be passed without any execution.
2 The FAX/TEL number (including the substitutive one) of the Rapid
key number 01 is copied into the Rapid key numbers 02 thru 48.
3 The FAX number of the Rapid key number 01 is copied into the
speed key numbers 001 thru 150.
4 If any chain dial is not set in the Rapid key number 01, the Rapid
key numbers 02 thru 48 and speed key numbers 001 thru 150 are
registered in the group number.
If any chain dial is set, any group will not be produced but the
chain dial setting alone of the Rapid dial will be canceled.
(In all other Rapid key numbers except 01, the chain dial is kept
as it is set.)
(16th and subsequential letters of the destination name registered in
the Rapid No. 01 will be discarded.)
2–5
FO-5500U/C
19) Motor aging
22) Dial test mode
•
Whether a document is present or not, the motor in the sending
system is kept in rotation until the STOP key is pressed.
•
The image quality selection key can be input during stop alone to
set the rotation speed for the image quality.
(Here, the speed for FINE is selected when the intermediate tone
is specified.)
The mode is used to inspect whether dialing is accurate in two kinds
of dial modes or not. All data which can be dialed in this mode are
automatically called up in both PB mode and DP mode.
•
The image quality for default at the start of execution is STD
regardless of the image quality selection priority of the main body.
•
For rotation, the ten key "1" selects the 1-2 phase excitation, "2"
selects the 2-phase excitation and "3" selects the micro step. It can
not be changed during rotation. The 1-2 phase excitation is set as
default.
When this mode is activated, the following operations will be automatically executed to their ends. Whether the dialed content is right or not
is judged with the external instrument which is connected to the line
cable.
1 After shift to the FAX diagnosis mode, press RAPID 22.
(Also switch the display with the [ ] and [#] keys.)
2 Press the START key.
3 Turn on CML, and dial the following in the PB mode.
1, 2, 3, 4, 5, 6, 7, 8, 0, , 0, #
4 Turn off CML 500 mS alone.
5 Dial the following in the DP mode.
1, 5, 9, 0
6 After dialing, turn off CML.
20) Stamp aging
•
•
It is impossible if any document is not set up.
•
The total number of stamps from entry of the mode is displayed on
the screen.
•
The ordinary operation aging which stamps a finish every document is executed in the ordinary copying mode.
The document is fed at the 10 mm intervals, and is continuously
stamped.
This mode uses the ordinary auto dial. (Accordingly, the signal sending time and minimum pause are all the same as ordinary.
The measurement result in this mode is completely all the same as in
the ordinary dial mode.
Moreover, the same process as above is also done in the dial test
mode which is executed in the product check mode.
21) Scanner set mode
•
23) Copy diag mode
The reading width and motor drive conditions are set.
In order to shorten the process time during production, this mode is
used to automatically switch the copy mode. Three menus are provided.
<Reading width>
1. Top margin
2. Bottom margin
3. Left adjustment (The left position alone is specified.)
1.
Specify the above values.
•
Select the above items 1, 2 and 3 with the [ ] and [#] keys, and
set the values with the [←] and [→] keys. The values can be set in
the range of +3.0 mm to -3.0 mm at the 0.1 mm intervals. While
the [←]/[→] key is continuously pressed one second or more, the
setting value is automatically increased/decreased (in the range
between the upper and lower limits).
•
Input the quality selection key, and the value will be respectively
set corresponding to the selected image quality. Here, the intermediate tone is the same as for the setting value of FINE.
•
±0.0 mm is default for all.
4. Motor
5. Phase
6. Slow-up
7. Slow-down
4. 6 steps
5. Selection of one mode from 1-2 phase, 2-phase and micro step
6. 3 steps
7. 3 steps
Input the quality selection key, and the value will be respectively
set corresponding to the selected image quality. Here, the intermediate tone is the same as for the setting value of FINE.
1.
2.
3.
4.
5.
6.
7.
Copy 1st document in the fine mode/density AUTO. (One
sheet is printed in the ordinary copy mode.)
Copy 2nd (subsequential) document in the intermediate
tone mode/density DARK. (In the ordinary copying mode,
one sheet is printed when the RESOLUTION key is pressed
three times.)
3. Continuously try the above items 1 and 2.
] and [#] keys, and
Setting values
•
Press the START key.
2. Try the copy in the mode fixed at COPY REDUCE 95% and
fine mode/density AUTO. At this time, don’t change the soft
key of COPY REDUCE. (Input of the image quality/density key
is invalid.
Specify the above values.
Select the above items d thru g with the [
select the setting value with the ten-key.
Set up two documents. (In case of two documents or more,
there is no problem.
When copy test is tried during production or is checked in two modes
(fine and intermediate tones), this mode is provided to reduce the
troublesome work which makes the operator stand aside to change
the mode. Accordingly, the fine and intermediate tones are merely
switched, and the mode is not switched to another mode. (Input of the
image quality/density key is invalid.)
<Drive conditions of motor>
•
1
2
3
4
TOP
BOTTOM
LEFT
MOTOR
PHASE
SLOW UP
SLOW DOWN
2–6
FO-5500U/C
2-2. Print diagnosis
Rapid key 02: Check pattern 1
Rapid key 01: Area print mode
The lateral stripe 2 pattern is printed on one sheet.
(Black 2 line and white 2 line are repeated.)
The effective printing area frame is printed in the specified sheet size.
The lateral stripe 2 pattern is printed on multiple pages.
Press the STOP key to end the printing.
4mm +- 12
1. Full Black pattern
2. Intermediate tone 2 pattern
3. Intermediate tone 1 pattern
4. Mesh point pattern
5. Longitudinal strip 2 pattern
6. Lateral strip 2 pattern
7. Longitudinal strip 1 pattern
8. Lateral strip 1 pattern
9. Full white pattern
The intermediate tone 1 is printed on one sheet.
Rapid key 05: Paper feed aging
The mode is used for aging related to the printing. In this mode, the
following modes are provided.
Blank paper aging mode (ALL WHITE AGING)
Whole black print aging mode (ALL BLACK AGING)
5% printing aging mode (5% AGING)
4% printing aging mode (4% AGING)
After selecting the paper-pass aging mode in the print diagnosis mode,
input the number of each mode above with the ten-key, and the mode will
be executed. The detailed specifications of each mode are described as
follows. Here, the operation in each mode is stopped only when the STOP
key is pressed by the operator or a printing-impossible error occurs.
1
2
3
4
pattern is repeated.
5mm
208mm
4mm ± 2
4mm
1. [Full black pattern]
•
2. [Intermediate tone 2 pattern]
Blank paper aging mode
In the mode, printing is continued in the whole white (white paper) printing
pattern until the STOP key is pressed by the operator. (In the printing area)
The left pattern is repeated.
•
Whole black printing aging mode
In the mode, printing is continued in the whole black (whole black) printing
pattern until the STOP key is pressed by the operator. (In the printing area)
Rapid key 6: Bias adjust mode
The mode is used to adjust the printing density of the printed image. The
image printing density is adjustable in six steps of 1 to 6.
For details, refer to the following table. (For selection, use the keys 1 thru
6.)
Image printing density
3. [Intermediate tone 1 pattern]
Thin
←
1
2
Default value
3
4
→
Thick
5
6
O
Rapid key 7: Life set mode
The mode is used to set the life counter of the printer and the counter of
the auto feeder at desired values. For setting, proceed with the following
procedure.
1 When
the life counter setting mode is selected, the following will be is
displayed.
4. [Mesh point pattern]
M A C H I N E
L I F E = 0 0 0 1 2 3
D R U M
L I F E = 0 0 0 1 2 3
L I F E 1 = 0 0 0 1 2 3
key
# key
L I F E 2 = 0 0 0 1 2 3
L I F E 3 = 0 0 0 1 2 3
F E E D E R
L I F E = 0 0 0 1 2 3
T O N E R
L I F E = 0 0 0 1 2 3
5. [Longitudinal strip 2 pattern]
Black 2 dot and white 2 dot are repeated in line.
6. [Lateral strip 2 pattern]
The cursor blinks at the top data.
Seven counters can be selected with the "#" and "
Black 2 line and white 2 line are repeated.
7. [Longitudinal strip 1 pattern]
Black 1 dot and white 1 dot are repaeted in line.
8. [Lateral strip 1 pattern]
Black 1 line and white 1 line are repeated.
9. [Full White pattern]
2–7
" keys.
FO-5500U/C
2 Inten-key.
the state 1, input a desired setting number of 6 digits with the
3 After
input of 6 digits, shift to another counter with the "#" and " " keys
as necessary. When all necessary counters are completely input, press
Rapid key 10: Top adjust mode
As the method to adjust the top margin for printing, adjust top-margin
adjusting VR on the PWB. If this mode is used at this time, adjustment is possible without the printing test every time when VR is
turned.
For the practical use, determine the adjusting value on the basis of
the old data, and adjust to the determined value in this mode. Then,
check it with the printing test.
the START key.
4 "STORED"
will be displayed with the set values stored into the memory. For checking, retry this mode.
Note:
The counter shows the operational state of the printer (how many sheets
have been printed since start of use? and others). The ordinary memory
does not reset the counter. For clearing, set 0 in this mode or use the life
counter clear mode in Item 3-9. (Accordingly, it is necessary to reset the
counter or do the clear process in addition to the ordinary memory clear if
the content in the memory on the control PWB is broken because of PWB
repair, etc. (In the production stage, it is necessary to execute this in the
last process.)
Rapid key 11: Life clear mode
The mode is used to respectively clear the life counter of the printer
and the counter of the auto feeder. For setting, proceed with the
following procedure.
1 When the life counter clearing mode is selected, the following will
be is displayed.
Rapid key 08: Life all clear
The mode is used to clear the life counter of the printer of the counter
of the auto feeder.
Note: The counter shows the operational state of the printer (e.g.
how many sheets have been printed since start of use?). The
ordinary memory does not reset the counter. For clearing, set
0 in the mode 8 or execute this mode. (Accordingly, it is necessary to reset this counter in addition to the ordinary memory
clear if the content in the memory on the control PWB is
broken because of PWB repair, etc. (In the production stage, it
is necessary to execute this in the last process.)
M A C H I N E
L I F E
C L E A R
D R U M
L I F E
C L E A R
L I F E 1
C L E A R
L I F E 2
C L E A R
L I F E 3
C L E A R
F E E D E R
L I F E
C L E A R
T O N E R
L I F E
C L E A R
# key
key
Rapid key 09: Life entry mode
(For Serviceman temporary counter)
The mode is used to set a desired value for the judgment value
(alarm judgment counter value) of the general purpose life counters 1
thru 3 of the printer. If the life of a consumable part (developer,
imprinter, etc) is set, the model which has the error display and RMS
function will inform RMS when the counter reaches the set value.
For setting, proceed with the following procedure.
Seven counters can be selected with the "#" and "
1 When the life counter setting mode is selected, the following will
be displayed.
and " " keys as necessary, and then press the CLEAR key.
When the necessary counters are completely cleared, press the
STOP key.
L I F E 1 = 0 0 0 0 0 0
# key
L I F E 2 = 0 0 0 0 0 0
key
L I F E 3 = 0 0 0 0 0 0
The cursor blinks at the top data.
Three counters can be selected with the "#" and "
" keys.
2 In the state 1, input the CLEAR key, and the counter will be
respectively cleared.
3 After one clear, move the cursor to another counter with the "#"
" keys.
2 In the state 1, input a desired setting number of 6 digits with the
ten-key.
3 After input of 6 digits, shift to another counter with the "#" and " "
keys as necessary. When all necessary counters are completely
input, press the START key.
4 "STORED" will be displayed with the set values stored into the
memory. For checking, retry this mode.
Note: The counter shows the operational state of the printer (how
many sheets have been printed since start of use? and others). The ordinary memory does not reset the counter. For
clearing, set 0 in this mode or use the life counter clear mode
in Item 3-9. (Accordingly, it is necessary to reset the counter or
do the clear process in addition to the ordinary memory clear if
the content in the memory on the control PWB is broken because of PWB repair, etc. (In the production stage, it is necessary to execute this in the last process.)
2–8
FO-5500U/C
3. How to make soft switch setting
To enter the softswitch mode, make the following key entries in sequence.
Press FUNCTION
9
8
7
START
01
START
SFT S W 1 = 0 0 0 0 0 0 0 0
Press FUNCTION key.
SFT S W 1 = 1 0 0 0 0 0 0 0
Press
key.
Press
key.
SFT S W 1 = 1 0 0 0 0 0 0 0
SFT S W 1 = 1 0 0 0 0 0 0 0
Bit1 - 8 are set.
SFT S W 1 = 1 0 0 0 0 0 0 0
Press START key during setting.
SFT S W 2 = 0 0 0 0 0 0 0 0
Soft SW2 - 99 are set.
S F T S W 99 = 0 0 0 0 0 0 0 0
To finish the settings halfway between
SW 1 and SW99, press the STOP key.
In this case, the setting being done to
the SW No. on display will be nullified
while settings done to the preceding
SW Nos. remain in effect.
The soft switch mode is terminated.
2–9
FO-5500U/C
4. Soft switch description
• Soft switch
SW DATA
NO. NO.
1
SW1
Recall interval
1
Binary input
8 4 2 1
0
OPTION
1 2 3 4 (Data No.)
1
Set to 1~15
3
EX
0 1 0 1
0
4
eg. Recall interval is set to 5 min.
Recall attempts
Binary input
0
No. =
5 6 7 8 (Data No.)
0
7
EX
0 0 1 0
1
8
eg. Recall attempt times is set to 2 times.
OPTION
Set to 1~15
0
1
Dialing mode
PULSE
TONE
0
2
Receive mode
AUTO
MANUAL
1
3
ECM mode
Off
On
0
4
Reserved
5
Polling security
On
Off
1
OPTION
6
Auto cover sheet
No
Yes
1
OPTION
7
JUNK-FAX function in manual reception
Yes
No
0
8
JUNK-FAX function
Yes
1
Number of rings for auto-receive
(0: No ring receive)
No
Binary input
8 4 2 1
0
OPTION
0
OPTION
Set to 0~15
No. =
1 2 3 4 (Data No.)
0
EX
0 0 0 1
0
eg. Number of rings for auto receive is set to 1.
Binary input
1
8 4 2 1
0
OPTION
No. =
5 6 7 8 (Data No.)
0
Set to 0~15
7
EX
0 0 0 0
0
8
eg. Switch to auto receive is set to disable.
6
Switch to auto-receive from manual receive
(0: No switch)
OPTION
0
4
5
Communication results printout
SW5
1
8 4 2 1
6
3
SW4
Remarks
No. =
2
SW3
Initial
setting
0
2
5
SW2
Switch setting and function
ITEM
Printed at
error only
Printed at
error/timer/
memory
only
0
OPTION
Printed at Not printed Printed
transmisevery time
sion mode
only
1
No. 1
0
0
0
1
1
0
2
No. 2
0
0
1
0
1
0
3
No. 3
1
0
0
0
0
1
4
Image addition function to the communication
result table (for memory transmission only)
On
Off
5
Reserved
6
1
OPTION
TEL billing code function
On
Off
0
OPTION
7
Billing code position
Before
After
1
OPTION
8
Multi-TTI feature
On
Off
0
OPTION
1
Time display format
24 hours
12 hours-AM/PM
0
2
Date display format
Month-Day-Year
Day-Month-Year
1
3
Header print
Off
On
0
4
Footer print
On
Off
0
5
Relay data output
No
Yes
0
6
Substitute reception
Off
On
0
7
Substitute reception conditions
Reception disable without
TSI
Reception enable without
TSI
0
8
CSI transmission
Off
On
0
0
2 – 10
FO-5500U/C
SW DATA
NO. NO.
ITEM
1
1
MH fixed
Yes
No (depend on remote
machine)
2
H2 mode
No
Yes
3
Reserved
0
0
V. 17
V. 29
14400 12000 9600
V. 27ter
7200
9600
7200
4800
2400
4
No. 4
0
0
0
0
0
0
0
0
5
No. 5
1
1
1
1
0
0
0
0
6
No. 6
0
0
0
0
0
0
0
0
7
No. 7
0
1
0
1
0
1
1
0
8
No. 8
0
0
1
1
1
1
0
0
Reception speed fixed
1
2
NO
V. 1714400PS
V. 299600BPS
V. 27ter4800BPS
No. 1
0
1
0
1
No. 2
0
1
1
0
Except left
table, work to
default.
0
0
3
DIS receive acknowledge in G3 transmission
Twice
Once in NSF reception,
twice in DIS reception
0
4
Non-modulated carrier in V.29 transmission
mode
On
Off
0
5
EOL detection timer
25sec
13sec
6
Reserved
7
Reserved
8
Max. length for TX/RX/Copy
SW7
0
TX: 432mm, RX: unlimited
TX/Copy: 432mm, RX: 1.5m
0Km
1.8Km
3.6Km
7.2Km
0
No. 1
0
0
1
1
0
2
No. 2
0
1
0
1
1
Reserved
Reserved
5
Signal transmission level
Effective to
international
comm.
0
1
4
When 14400BPS
MODEM used,
setting to
14400bps is
ignore.
0
Line equalizer
3
Remarks
0
Modem speed
(DCS data reception speed)
SW6
SW8
Initial
setting
0
0
0
Binary input
8 4 2 1
1
6
No. =
5 6 7 8 (Data No.)
0
7
EX
1 0 0 0
0
8
eg. Signal transmission level is set to -11dBm
2 – 11
0
Effective to
transmission
FO-5500U/C
SW DATA
NO. NO.
SW9
SW10
1
CED tone signal interval
500ms
75ms
2
CI signal OFF detect enable time
350ms or more
700ms or more
0
3
Equalizer freeze
On
Off
0
4
Equalizer freeze conditions
All
7200bps
5
Reserved
6
CED detection time
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
3
F.A.S.T. (RMS) mode
4
Reserved
1000ms
0
2000ms
0
0
On
Off
0
0
OFF
STANDARD
RING1
RING2
RING3
No. 5
0
0
1
0
1
0
6
No. 6
0
0
0
1
1
0
7
No. 7
0
0
0
0
0
0
8
No. 8
0
1
0
0
0
0
Binary input
8 4 2 1
1
2
No. =
1 2 3 4 (Data No.)
0
3
EX
1 0 1 0
1
4
eg. Retransmission time set to 10 times.
Memory retransmission interval
Binary input
0
No. =
5 6 7 8 (Data No.)
0
7
EX
0 1 0 1
0
8
eg. Retransmission interval set to 5 min.
1
Reserved
2
Reserved
0
0
0
3sec
1sec
No BEEP
No BEEP
3
No. 3
0
0
1
1
0
4
No. 4
0
1
0
1
0
Handle to no error
5
Action when RTN received
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
2 – 12
Handle to error
OPTION
0
8 4 2 1
6
Alarm buzzer
SW13
|
SW26
0
5
Memory retransmission times
Remarks
0
Distinctive ringing
5
SW12
Initial
setting
0
1
1
SW11
ITEM
0
OPTION
FO-5500U/C
SW DATA
NO. NO.
SW27
ITEM
1
Reserved
2
Reserved
3
Verification STAMP
4
Reserved
1
6
7
Reserved
8
Reserved
0
Yes
No
MIDDLE
LOW
No. 5
0
0
1
1
1
No. 6
0
1
0
1
1
0
0
HIGH
HIGH
MIDDLE
LOW
1
No. 1
0
0
1
1
1
2
No. 2
0
1
0
1
1
HIGH
HIGH
MIDDLE
LOW
3
No. 3
0
0
1
1
1
4
No. 4
0
1
0
1
0
Ringer volume
Off
HIGH
MIDDLE
LOW
5
No. 5
0
0
1
1
1
6
No. 6
0
1
0
1
1
7
Reserved
0
8
Reserved
0
1
Reserved
2
PC I/F mode
On
Off
3
Auto receive with PC I/F
PC
FAX
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
1
Resistration of header
2
Reserved
3
Continuous serial polling
0
SW31
0
OPTION
0
OPTION
0
Disabled
Enabled
0
0
On
Off
0
0minutes 30minutes 60minutes 120minutes
Dialing interval in continuous serial polling
SW30
Invalid if not
mounted.
0
HIGH
Handset volume
SW29
0
Off
Speaker volume
SW28
Remarks
0
Key buzzer volume
5
Initial
setting
0
4
No. 3
0
0
1
1
0
5
No. 4
0
1
0
1
0
6
Reserved
7
Reserved
0
8
Quick on-line
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
1
6
Reserved
0
7
Reserved
1
8
Reserved
0
0
Yes
No
2 – 13
1
When SW30-3
is ON to be set
by OPTION
setting
FO-5500U/C
SW DATA
NO. NO.
SW32
ITEM
1
On
Off
OPTION
Reserved
0
3
Reserved
0
4
Changeover of print cassette
On
Selection of print cassette
(when double cassette)
(FO-6500)
W cassette Auto. TUL
Off
1
TLU
UTL
ULT
LTU
LUT
OPTION
Indicate of
priority
T...TRAY
5
No. 5
0
1
1
0
0
0
0
0
U...UPPER
6
No. 6
0
0
0
1
1
0
0
0
L...LOWER
7
No. 7
0
0
0
0
0
1
1
0
0
1
0
1
0
1
0
0
No. 8
Selection of print cassette
(when single cassette)
(FO-5500/4500)
Single
cassette
Auto. T→C C→T
Work in auto mode
except in this table.
Indicate of
priority
No. 5
0
1
0
0
T...TRAY
6
No. 6
0
0
1
0
C...CASSETTE
7
No. 7
0
0
0
0
8
No. 8
0
1
1
0
Heater mode
No. 1
2
No. 2
Density adjustment of print bias
Binary input
Always on
Always off
Off timer
0
0
1
0
OPTION
0
1
0
1
4 2 1
3
No. =
3 4 5 (Data No.)
4
EX
1 0 0
5
eg. Bias is set to level 4.
1: faint 6: deep
1
0
Reserved
0
7
Reserved
0
8
Reserved
1
Start time of heater OFF timer
(Upper digit of hour)
3
0
Binary input
8 4 2 1
0
No. =
1 2 3 4 (Data No.)
0
EX
0 0 0 1
4
5
0
8 4 2 1
0
5 6 7 8 (Data No.)
0
7
EX
0 1 0 1
0
8
eg. Start time is set to 15: XX
1
2
(Lower digit of hour)
(Upper digit of minute)
3
Binary input
Binary input
5
0
No. =
1 2 3 4 (Data No.)
0
EX
0 1 0 0
0
(Lower digit of minute)
8 4 2 1
0
5 6 7 8 (Data No.)
0
7
EX
0 0 0 0
0
8
eg. Start time is set to XX: 40
2
End time of heater OFF timer
(Upper digit of hour)
3
Binary input
Binary input
0
No. =
1 2 3 4 (Data No.)
0
EX
0 0 1 0
0
OPTION
0
8 4 2 1
0
No. =
5 6 7 8 (Data No.)
0
7
EX
0 0 0 1
0
8
eg. End time is set to 21: XX
0
6
OPTION
0
8 4 2 1
4
5
OPTION
0
No. =
1
OPTION
0
8 4 2 1
4
6
OPTION
0
No. =
6
set to 1~6.
set to 0,7 is
equal to 4.
0
6
2
SW36
0
Print hold
1
SW35
Remarks
2
5
SW34
Initial
setting
1
8
SW33
0
(Lower digit of hour)
Binary input
2 – 14
OPTION
FO-5500U/C
SW DATA
NO. NO.
1
2
(Upper digit of minute)
3
SW37
SW40
SW41
Binary input
0
Initial
setting
Remarks
OPTION
8 4 2 1
0
No. =
1 2 3 4 (Data No.)
0
EX
0 0 1 1
0
0
8 4 2 1
0
No. =
5 6 7 8 (Data No.)
0
7
EX
0 1 0 1
0
8
eg. End time is set to XX: 35
6
SW39
1
4
5
SW38
ITEM
(Lower digit of minute)
Binary input
0
1
Reserved
1
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
1
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
1
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
1
4
Reserved
0
5
Reserved
0
6
Reserved
1
7
Reserved
0
8
Reserved
1
2 – 15
OPTION
FO-5500U/C
SW DATA
NO. NO.
SW42
SW43
SW44
SW45
ITEM
1
Initial
setting
0
1
Reserved
0
2
Reserved
0
3
Reserved
1
4
Reserved
0
5
Reserved
0
6
Reserved
1
7
Reserved
0
8
Reserved
1
1
Reserved
1
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
1
7
Reserved
0
8
Reserved
1
Automatic printing of activity report
Yes (When memory full)
No (First data is cleared
when memory full)
0
2
Printout of total time and total number of
pages on activity report
Off
On
0
3
Reserved
4
Department function
5
Department ID digit
Remarks
1
OPTION
0
On
Off
Binary input
8 4 2 1
0
0
OPTION
6
No. =
5 6 7 8 (Data No.)
1
Set is 3~9.
7
EX
0 1 0 0
0
8
eg. Department ID is set to 4 digits.
0
1
Picture quality priority mode
Fine
Standard
0
OPTION
2
Cut-off mode (when copy mode)
Continue
Cut-off
0
OPTION
3
Scanning ratio in memory input
1:1
Reduce
0
4
Reserved
5
Reserved
0
0
Reduce ratio (when copy mode)
AUTO
100%
95%
89%
74%
6
No. 6
0
1
0
0
1
1
7
No. 7
0
0
1
0
1
0
8
No. 8
0
0
0
1
0
0
2 – 16
Memory
scanning
FO-5500U/C
SW DATA
NO. NO.
ITEM
1
Reserved
2
Reserved
1
0
0
Density adjustment
(when Fine/STD mode)
SW46
Normal
SW48
SW49
SW50
SW51
Faint
Deep
Deep
(when Dark
mode)
3
No. 1
0
0
1
1
0
4
No. 2
0
1
0
1
0
Normal
Faint
Deep
Deep
Density adjustment
(when Half-tone mode)
SW47
Initial
setting
0
(when Dark
mode)
5
No. 3
0
0
1
1
0
6
No. 4
0
1
0
1
0
7
HTF correction in Half-tone mode
On
Off
1
8
MTF correction in Half-tone mode
Strong
Weak
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
2 – 17
Remarks
FO-5500U/C
SW DATA
NO. NO.
SW52
SW53
SW54
SW55
SW56
ITEM
1
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
1
2
Reserved
1
3
Reserved
1
4
Reserved
5
Printing when toner empty
1
Printing
Reduction of print data
SW57
Initial
setting
0
Stop
0
AUTO
100%
94%
88%
73%
6
No. 6
0
1
0
0
1
0
7
No. 7
0
0
1
0
1
0
8
No. 8
0
0
0
1
0
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
2 – 18
Remarks
FO-5500U/C
SW DATA
NO. NO.
SW58
SW59
SW60
SW61
SW62
SW63
ITEM
1
0
Initial
setting
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
2 – 19
Remarks
FO-5500U/C
SW DATA
NO. NO.
SW64
SW65
SW66
SW67
SW68
ITEM
1
0
Initial
setting
Remarks
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
1
Cassette define (LTR/A4): Tray
A4
LTR
0
2
Cassette define (LTR/A4): Upper
A4
LTR
0
When W
cassette
3
Cassette define (LTR/A4): Lower
A4
LTR
0
Ignore when W
cassette.
4
Separation of image area in the half-tone
On
Off
1
5
Removal of notch in the binary mode
On
Off
6
Reserved
1
7
Reserved
1
8
Reserved
0
0
SW69
2 – 20
1
FO-5500U/C
SW DATA
NO. NO.
SW70
1
Initial
setting
0
1
Reserved
1
2
Reserved
1
3
Reserved
1
4
Reserved
1
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
Black line detection
(When transmission scanning)
0
Continued black line count when detected
1
2
3
4
5
6
7
Unused
1
No. 1
0
0
0
0
0
0
0
0
0
2
No. 2
0
0
0
0
1
1
1
1
0
3
No. 3
0
0
1
1
0
0
1
1
1
4
No. 4
0
1
0
1
0
1
0
1
1
All white page detection
SW71
ITEM
All white line count ratio against total count of page to
judge the white page
Unused
1.0% 1.5% 2.0% 2.5% 3.0% 3.5% 4.0%
5
No. 5
0
0
0
0
0
0
0
0
0
6
No. 6
0
0
0
0
1
1
1
1
1
7
No. 7
0
0
1
1
0
0
1
1
0
8
No. 8
0
1
0
1
0
1
0
1
1
4.5% 5.0% 5.5% 6.0% 7.0% 8.0% 9.0% 10.0%
5
No. 5
1
1
1
1
1
1
1
1
6
No. 6
0
0
0
0
1
1
1
1
7
No. 7
0
0
1
1
0
0
1
1
8
No. 8
0
1
0
1
0
1
0
1
Black line detection
(When copy scanning)
1
2
3
4
5
6
7
Unused
1
No. 1
0
0
0
0
0
0
0
0
0
2
No. 2
0
0
0
0
1
1
1
1
0
3
No. 3
0
0
1
1
0
0
1
1
1
4
No. 4
0
1
0
1
0
1
0
1
1
White page detect
(When copy scanning)
SW72
Continued black line count when detected
Unused
1.0% 1.5% 2.0% 2.5% 3.0% 3.5% 4.0%
5
No. 5
0
0
0
0
0
0
0
0
0
6
No. 6
0
0
0
0
1
1
1
1
1
7
No. 7
0
0
1
1
0
0
1
1
0
8
No. 8
0
1
0
1
0
1
0
1
1
4.5% 5.0% 5.5% 6.0% 7.0% 8.0% 9.0% 10.0%
SW73
|
SW99
5
No. 5
1
1
1
1
1
1
1
1
6
No. 6
0
0
0
0
1
1
1
1
7
No. 7
0
0
1
1
0
0
1
1
8
No. 8
0
1
0
1
0
1
0
1
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
2 – 21
Remarks
FO-5500U/C
• Soft switch function description
SW1 No. 1 ~ No. 4 Recall interval
Choice is made for a recall interval for speed and rapid dial-numbers.
Use a binary number to program this. If set to 0 accidentally, 1 will be
assumed.
SW1 No. 5 ~ No. 8 Recall attempts
Choice is made as to how many recall attempts should be made. Use
a binary number to program this.
SW2 No. 1 Dialing mode
Switch the type according to the telephone circuit connected to the
facsimile.
0: PULSE DIAL
1: TONE DIAL
SW2 No. 2 Receive mode
Auto/manual receiving mode is set.
SW2 No. 3 ECM mode
Used to determine ECM mode function. Refer to the following table.
SW2-No.3 ECM MODE
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
SW6-No.1 MH FIXED
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Compression
method
ECM MMR mode
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
ECM MR mode
Yes
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
ECM MMH mode
Yes
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
No
ECM MH mode
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
MR mode
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MH mode
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
(Depending on remote machine)
SW3 No. 1 ~ No. 4 Number of rings for auto-receive
(0: No ring receive)
When the machine is set in the auto receive mode, the number of
rings before answering can be selected. It may be set from one to
nine rings using a binary number. If the soft switch was set to 1, a
direct connection is made to the facsimile. If a facsimile. If it was set
to 0 accidentally, receive ring is set to 1. If it was above 9, receive
rings are set to 9. So, this has to be corrected.
SW2 No. 4 Reserved
Set to "0".
SW2 No. 5 Polling security
This switch is employed to enable or disable the polling operation
using the ID code verification function, in order to prevent unauthorized polling operation.
SW2 No. 6 Auto cover sheet
When "1" (=YES) is selected, the cover sheet is automatically sent
after transmission of the original to notify the receiver of the number
of original sheets transmitted.
SW3 No. 5 ~ No. 8 Switch to auto-receive from manual receive
(0: No switch)
Choice is made after how many rings in the manual receive mode it
should be automatically change to auto answer mode or remain in the
manual receive mode. Entering the binary number 0 forces the machine to remain in the manual answer mode. If a number between 1
and 9 is entered, the machine will go into the answer mode after the
given number of rings. However, it can be used as an ordinary telephone if the handset is taken off the hook before this programmed
number is finished. If entry of a number above 9 by accident, it will be
set to 9. In this case, it must be corrected to the proper number.
SW2 No. 7 JNNK-FAX function in manual reception
It is set whether JUNK-FAX is functioned in the manual receiving
mode or not.
SW2 No. 8 JUNK-FAX function
This function is used to receive data from a specific remote machine
(station registered in entry mode). It is the function that refused a
reception in the case that TSI of remote machine matched with fax
number of the station registered.
0: No
1: Yes
2 – 22
FO-5500U/C
SW4 No. 1 ~ No. 3 Communication results printout
SW5 No. 7 Substitute reception condition
Selection of substitute reception according to existence of TEL number from transmitting side. Initial setting allows substitute reception
without CSI. If set to "no", the receiver cannot receive any documents.
It is possible to obtain communication results after each transaction.
Normally, the switch is set (No. 1: 0, No. 2: 0, No. 3: 1) so that the
communication result is produced only a communication error is encountered. If No. 1 was set to 1, No. 2 was set to 1 and No. 3 was set
to 0, the communication result will be produced every time a communication is done, even if the communication was successful.
SW5 No. 8 CSI transmission
CSI signal contains the sender’s phone number registered in the machine. If this switch is set to "1", no sender’s name will be printed at
the receiving side.
If No. 1 was set to 0, No. 2 to 1 and No. 3 to 0, the communication
result will be produced every transmission.
SW6 No. 1 MH fixed
Normally set to allow automatic selection of MH and MR mode according to the remote side.
If set to 1, the mode is fixed to MH and is useful if the remote side is a
MH only unit; or a lot of image distortion is met due to a bad line.
Setting No. 1 to 1 No. 2 to 0 and No. 3 to 0 will disable this function.
No transaction report will be printed.
If No. 1 was set to 0, No. 2 to 0 and No. 3 to 0, the communication
result is produced only after a timer and memory transmission or when
a communication error is encountered.
SW6 No. 2 H2 mode
Used to determine H2 mode (15 sec transmission mode). When set to
OFF, H2 mode is inhibited even though the transmitting machine has
H2 mode.
SW4 No. 4 Image addition function to the communication result
table (for memory transmission only)
Used to set addition of sending image to the communication result
table.
SW6 No. 3 Reserved
Set to "0".
SW4 No. 5 Reserved
Set to "0".
SW6 No. 4 ~ No. 8 Modem speed (DCS date reception speed)
Used to determine the initial modem speed. The default is 14400BPS
(V17). It may be necessary to program it to a slower speed when
frequent line fallback is encountered, in order to save the time required for the fallback procedure.
SW4 No. 6 TEL billing code function
When set to "1", the TEL billing code function is enabled.
SW4 No. 7 Billing code position
When set to "1", the billing code is delivered before dialing the remote
number. When set to "0", the billing code is delivered after dialing.
SW7 No. 1, No. 2 Reception speed fixed
The transferable speed of modem in the receiving mode is set.
SW4 No. 8 Multi-TTI feature
When this switch is set to "1", Multi TTI function is enabled.
SW7 No. 3 DIS receive acknowledge during G3 transmission
Used to make a choice of whether reception of NSF (DIS) is acknowledged after receiving two NSFs (DISs) or receiving one NSF (two
DISs).
It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.
SW5 No. 1 Time display format
When this switch is set to "0", time is displayed in 12-hour system.
When set to "1", 24-hour system.
SW5 No. 2 Date display format
Used to select date display/print formats.
SW7 No. 4 Non-modulated carrier in V29 transmission mode
Though transmission of a non-modulated carrier is not required for
transmission by the V29 modem according to the CCITT Recommendation, it may be permitted to send a non-modulated carrier before the
image signal to avoid an echo suppression problem.
SW5 No. 3 Header print
When it is set at 0, sender’s name, sending page number and so on
are automatically printed in the recording paper on the receiving side
during transmission. Thus, the sender can be known on the receiving
side.
It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.
0: Applied.
SW7 No. 5 EOL detection timer
1: Not applied.
Used to make a choice of whether to use the 25-second or 13-second
timer for detection of End of line.
This is effective to override communication failures with some facsimile models that have longer End of line detection.
SW5 No. 4 Footer print
When set to "1", the date of reception, the sender machine No., and
the page No. are automatically recorded at the end of reception.
SW5 No. 5 Relay data output
SW7 No. 6, No. 7 Reserved
Set to "0".
0: Output ON
1: Output OFF
SW7 No. 8 Max. length for TX/RX/Copy
Used to set the maximum page length.
To avoid possible paper jam, the page length is normally limited to
432 mm for copy or transmit, and 1.5 meters for receive.
It is possible to set it to "No limit" to transmit/receive a long document,
such as a computer print form, etc. (In this case, the receiver/transmitter must also be set to no limit.)
SW5 No. 6 Substitute reception
Selection of substitute reception in the case of recording paper exhausted or paper jam. If set to "NO", auto receive is disabled even
when the receive memory is ready to receive.
Substitute reception is not performed even during receive operation.
2 – 23
FO-5500U/C
SW8 No. 1, No. 2 Line equalizer
Needs to be set to the line characteristics. A guide line is the distance
between the exchange office and the telephone terminal. Since it
needs not to be set in the normal case since it has been set to 1.8Km,
it should be corrected in case communication failures occur frequently.
2S
4S
STANDARD
2S
2S
Set to "0".
1.5S
3S
SW8 No. 5 ~ No. 8 Signal transmission level
Used to control the signal transmission level in the range of –0dB to
–15dB.
1S
4S
SW9 No. 1 CED tone signal interval
For international communication, the 2100Hz CED tone may act as an
echo suppresser switch, causing a communication problem. Though
this soft switch is normally set to "0", it should be set to "1" so as to
change the time between CED tone and DIS signal from 75ms to
500ms to eliminate the communication problem caused by echo.
0.5S
1.5S
0.5S
RING
PATTERN 1
for USA
4S
0.8S
0.8S
0.5S
SW9 No. 2 CI signal OFF detect enable time
Used to set the continuous detection time during OFF period of CI
signal. Normally set to 700ms, where the short ring (500ms: OFF
period) cannot be detected. Therefore, selection of 350ms is allowed.
RING
PATTERN 2
for USA
0.2S
0.2S
RING
PATTERN 3
for USA
SW9 No. 3 Equalization freeze
This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in unfavorable state
and picture cannot be received. Usually, the control is executed according to the state of line where the equalizer setting is changed
always.
4S
0.3S 0.8S 0.3S
4S
0.4S 0.4S 0.8S
0.2S 0.2S
RING
PATTERN 1
for CANADA
4S
1S
1S
0.5S
RING
PATTERN 2
for CANADA
0.5S
SW9 No. 4 Equalization freeze conditions
Setting which specifies SW9 No.3 control only in condition of 7200bps
modem speed.
RING
PATTERN 3
for CANADA
0.5S
3.5S
1S
0.5S
0.5S
0.5S
0.5S
0.5S
0.5S
3S
1S
3S
SW9 No. 5 Reserved
Set to "0".
SW9 No. 6 CED detection time.
The detection time of the CED signal from the called side in the auto
calling mode is set.
SW11 No. 1 ~ No. 4 Memory retransmission times
The number of memory retransmissions is set.
SW11 No. 5 ~ No. 8 Memory retransmission interval
The interval between memory retransmissions is set.
Set to "0".
Set to "0".
Set to "0".
SW12 No. 3, No. 4 Alarm buzzer
The sounding length of the buzzer for normal end of operation is set.
SW10 No. 3 F.A.S.T (Remote maintenance system) mode
Used to determine remote maintenance system (F.A.ST) function.
SW12 No. 5 Action when RTN received
The operation is set when the RTN signal is received in the G3
transmission mode.
SW10 No. 4 Reserved
Set to "0".
SW10 No. 5 ~ No. 8 Distinctive ringing
When the ringing setting is turned off, all of the CI signal are received.
When any of the standard, and ring patterns 1 through 3 is selected
for the ringing setting, only the selected CI signal is received.
SW12 No. 6 ~ No. 8 Reserved
Set to "0".
SW13 No. 1 ~ No. 8 - SW26 No. 1 ~ No. 8 Reserved
Set to "0".
CI signal patterns
The CI signal patterns consists of the standard pattern, and ring patterns 1 through 7. The standard pattern is the conventional one.
2 – 24
FO-5500U/C
Set to "0".
SW31 No.1 ~ No.8 Reserved
Set to "0".
SW27 No. 3 Verification STAMP
End stamp:
It is set whether the red round mark is stamped at the bottom margin
of the document every page in the memory input mode and document
sending mode or not.
SW32 No. 1 Print hold
When set to "1", the print hold function is enabled.
Set to "0".
SW32 No. 4 Changeover of Print cassette
When the cassette selection priority is set to the upper priority or the
lower priority and paper in the cassette is exhausted, this function is
used to set changeover of the cassette of not.
SW27 No. 4 Reserved
Set to "0".
SW27 No. 5, No. 6 Key buzzer volume
Key buzzer volume:
The sound volume of key inputting buzzer and other buzzers is set.
SW32 No. 5 ~ No. 8 Selection of print cassette
Used to set the priority of selection of the recording paper cassettes.
(Auto selection/Upper priority/Lower priority)
Set to "0".
SW33 No.1 No. 2 Heater mode
Used to set ON/OFF of the heater. Three settings are available: always ON, always OFF, and OFF timer. (Only when Off timer is selected, SW34-SW37 settings are valid.)
SW28 No. 1, No. 2 Speaker volume
Speaker volume:
The sound volume of the speaker in the on-hook mode is set.
SW28 No. 3, No. 4 Handset volume
Handset volume:
The volume of sound heard from the receiver is set.
SW33 No. 3 ~ No. 5 Density adjustment of print bias
The density of printing is set.
It can be also set in the print diagnosis mode.
SW28 No. 5, No. 6 Ringer volume
Ringer volume:
The calling sound volume of CI signal receiving is set.
Sw33 No. 6 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW34 No. 1 ~ No. 4 Start time of heater OFF time (Upper digit of
hour)
Used to set the start time of the heater OFF timer. (Enter in 24-hour
system.)
SW29 No. 1 Reserved
Set to "0".
SW34 No. 5 ~ No. 8 Start time of heater OFF time (Lower digit of
hour)
system.)
SW29 No. 2 PC I/F mode
PC I/F mode:
The interface with the personal computer is selected.
SW29 No. 3 Auto receive with PC I/F
Automatic receiving of I/F mode:
Which receives the call is determined.
SW35 No. 1 ~ NO. 4 Start time of heater OFF time (Upper digit of
minute)
system.)
Set to "0".
SW35 No. 5 ~ No. 8 Start time of heater OFF time (Lower digit of
hour)
system.)
SW30 No. 1 Resistration of header
Used make a choice of whether the registered senders phone number
can be changed or not. If the switch is set to "1", new registration of
the senders phone number is disabled to prevent accidental incorrect
input.
SW36 No. 1 ~ No. 4 End time of heater OFF time (Upper digit of
hour)
Used to set the end time of the heater OFF timer. (Enter in 24-hour
system.)
SW30 No. 2 Reserved
Set to "0".
SW36 No. 5 ~ No. 8 End time of heater OFF time (Lower digit of
hour)
system.)
SW30 No. 3 Continuous serial polling
Turns on/off the continuous polling function.
SW30 No. 4, No. 5 Dialing interval in continuous serial polling
Used to set continuous serial polling interval time.
SW37 No. 1 ~ No. 4 End time of heater OFF time (Upper digit of
minute)
system.)
Set to "0".
SW30 No. 8 Quick on-line
It is selected whether auto dial call is activated in the memory input
mode when one document is completely read or when all pages are
completely read.
SW37 No. 5 ~ No. 8 End time of heater OFF time (Lower digit of
minute)
system.)
2 – 25
FO-5500U/C
Set to "0".
SW46 No. 3, No. 4 Density adjustment (when Fine/STD mode)
This is used for density adjustment in fine/standard mode. Adjust the
density according to that of frequently used original.
Set to "Dark" for darker reading (either in the auto or the dark mode)
of light original. Set to "Light" for lighter reading (either in the auto or
the dark mode) of dark original.
Set to "Dark only in dark mode" for darker reading only in the dark
mode.
SW44 No. 1 Automatic printing of activity report
This soft switch is used to select; whether or not to produce the
activity report when the memory is full (about 50 items). An activity
report can be produced when the following key entry command is
made.
"FUNC", "2", "#", "START"
SW46 No. 5, No. 6 Density adjustment (when Half-tone mode)
This is used for density adjustment in the half tone. Setting procedures are the same as SW46 No. 3, No. 4.
After producing the activity report, all the data in the memory will be
cleared.
When the switch function is set to "0" (NO), the data in memory will be
deleted from the oldest as it reaches the maximum memory capacity
(approx. 50 items).
SW46 No. 7 HTF correction in Half-tone mode
In the half tone mode, image area is separated from character area
and processed separately to eliminate unclear character transmission.
This switch is used to change the criteria of judgement of separation.
When "Strong" (= 1) is selected, more area is judge d as character
area, providing clearer characters.
On the contrary, however, edges of image area may be emphasized.
It is advisable to restrict the use of this function only when clear
characters must be transmitted, and to use the function of "Weak" (=
0) for general cases.
SW44 No. 2 Printout of total time and total number of pages on
activity report
Used to make a choice of whether the total communication time and
pages are recorded in the activity report.
SW44 No. 3 Reserved
Set to "0".
SW46 No.8 MTF correction in Half-tone mode
This allows selection of MTF correction (dimness correction) in the
half tone mode. When "Strong" (= 1) is selected, the whole image
becomes soft and mild, On the contrary, however, cleamess of characters will be reduced. Normally set to "Strong" (= 1).
SW44 No. 4 Department function
This model has the department audit feature, it has to be set to 1 to
utilize this feature.
SW44 No. 5 ~ No. 8 Department ID digit
Used to set the department ID digit number. When set to "D", the
number is "4".
Set to "0".
SW45 No. 1 Picture qualitypriority mode
Used to set to the transmission mode which is automatically selected
when the MODE key is not pressed. In the copy mode, however, the
fine mode is automatically selected unless the MODE key is manually
set to another mode.
Set to "0".
SW45 No. 2 Cut-off mode (when copy mode)
When in copy, if the scanned data is out of the range of recrding, the
operator has one of the choices below using the switch.
SW56 No. 6 ~ No. 8 Reduction of print data
Contraction ratio of receiving is set.
It can be changed even in the optional mode.
0: Continue:
Data is printed onto the next page with the last
20mm also printed at the beginning of the next page.
Set to "0".
1: Cut off:
Data scanned out of the limit is cut off (a page is
printed.)
SW69 No. 1 (Cassette define (LTR/A4): Tray
A4 cassette can be used.
Set 0 or 1 for all of three bits.
Moreover, do not change the setting during printing.
SW56 No. 5 Printing when toner empty
It is set whether printing is stopped for empty toner or not.
SW45 No. 3 Scanning ratio in memory input
In the case of memory transmission, etc., only letter size (A4) documents can be stored in the memory. To input B4 documents into the
memory, therefore, the B4 documents must be reduced to letter size
(A4) or the both ends of the B4 documents will be cut off to input the
center letter-size (A4) portion. This switch provides the selection.
SW69 No. 2 Cassette define (LTR/A4): Upper
0: Reduced to A4 size and inputted.
SW69 No. 3 Cassette define (LTR/A4): Lower
1: The both ends are cut off and the center portion (A4 size) is
inputted.
Set to "0".
SW69 No. 4 Separation of image area in the half-tone
This allows selection of MTF correction (dimness correction) in the
half tone mode. When "NO" (= 1) is selected, the whole image becomes soft and mild, On the contrary, however, cleamess of characters will be reduced. Normally set to "NO" (= 1).
SW45 No. 6~No. 8 Reduce ratio (when copy mode)
Contraction ratio of copying is set.
It can be changed even in the optional mode.
Set to "0".
SW69 No. 5 Removal of notch in the binary mode
The notch signal is removed in the binary mode.
Set to "0".
2 – 26
FO-5500U/C
Set to "0".
SW71 No. 1 ~ No. 4 Black line detection
(When transmission scanning).
Number of continuous judgements of black lines during duplex scan.
SW71 No. 5 ~ No. 8 All white page detection
Ratio of black and white during duplex scan.
SW72 No. 1 ~ No. 4 Black line detection (When copy scanning)
Number of continuous judgements of black lines during duplex scan.
SW72 No. 5 ~ No. 8 White page detect (When copy scanning)
Ratio of black and white during duplex scan.
Set to "0".
2 – 27
FO-5500U/C
[3] Troubleshooting
1. Fax troubleshooting
Refer to the following actions to troubleshoot any of problems mentioned in 1-4.
•
[1]
A communication error evoked.
•
[2]
Image distortion produced.
[3]
Unable to do overseas communication.
[4]
Communication speed slow liable to failback.
•
Can be used in all cases.
Slow down the transmission speed SOFT SWITCH 6-4, 5, 6, 7, 8
Can be used in case [2] [3]
•
Replace the TEL/LIU PWB.
Increase the transmission level SOFT SWITCH 8-5, 6, 7, 8
•
Can be used in case [1] [2] [3]
•
Apply line equalization SOFT SWITCH 8-1, 2
Replace the control PWB.
* If transmission problems still exist on the machine, use the following format and check the related matters.
Decrease the transmission level SOFT SWITCH 8-5, 6, 7, 8
Can be used in case [3]
TO:
ATT:
Ref.No. :
CC:
ATT:
Date
:
Dept
:
Sign
:
FM:
***** Facsimile communication problem *****
From: Mr.
Our customer
Other party
Ref.No.:
Fax Tel No.:
Date:
Name
Tel No.
Address
Fax No.
Contact person
Model name
Name
Tel No.
Address
Fax No.
Contact person
Problem mode
Model name
Line: Domestic/international
Reception/Transmission
Mode:
G3
Phase: A. B. C. D.
Automatic reception / Manual reception
Automatic dialing / Manual dialing / Others
Frequency:
Confirmation
item
%
Our customer
ROM version:
Other party
B1
B2
Please mark problem with an X
No problem is: 0
A1
A1
A2
C1
D2
C2
E1
E2
Our service
D1
Other party's service
Comment
Counter-measure
**** Please attach the G3 data and activity report on problem. ****
2 – 28
A2
B1
B2 C1 C2 D1 D2
Transmission level setting is (
customer
Transmission level (
) dBm
Reception level (
) dBm
By level meter at B1 and B2
E1
) dB at our
E2
FO-5500U/C
(5) Exit fan malfunction
The voltage equivalent to the current*1 of the Exit Fan Motor remains
160 mV or lower for 2 sec.
2. Printer trouble detection
(1) Paper jam
The printer recognizes if paper remains inside the printer by detecting
the status of the Paper Take-Up Sensor (PC1) and the Paper Exit
Sensor (PC3). A paper jam is detected by the timing that PC1 and
PC3 become activated or deactivated.
When a paper jam is detected, the drive for all elements is stopped
except for the Fan Motor (M3) , excluding the two following cases.
• During multi printing
*1: detected by converting the Motor current into voltage.
How to Reset these malfunctions
Turn OFF The Power ON/OFF Switch (S1).
When condition 1 listed below is detected and paper remains in the
printer, all elements except the Fan Motor (M3) will be stopped
after the paper is fed out of the printer.
•
During single printing
When condition 1 listed below is detected and paper does not
remains in the printer, elements except the Heater Lamp (H1) and
Fan Moter (M3) will ve stopped.
1. The Paper Take-Up Sensor (PC1) does not activate within 2
sec, after the Paper Take-Up Roller in the printer starts rotating,
or within 4 sec. after the Paper Take-Up Roller in the optional
250 Sheet Second Tray starts rotating.
2. The Paper Take-Up Sensor (PC1) activates when the Power
ON/OFF Switch (S1) is turmed ON, or when the Upper Unit is
closed.
3. The Paper Exit Senspr (PC3) activates when the Power
ON/OFF Switch(S1) is turned ON, of when the Upper Unit is
closed.
4. The Paper Take-Up Sensor (PC1) does not deactivate within 11
sec. after the paper leading edge reaches the Paper Take-Up
Sensor (PC1).
5. The Paper Exit Sensor (PC3) does not activate within 3.5 to 4.5
sec. after the paper leading edge reaches the Paper Take-Up
Sensor (PC1).
6. The Paper Exit Sensor (PC3) does not deactivate within 3.4 to
4.7 sec. afer the paper trailing edge passes the paperTake-Up
Sensor (PC1).
(2) Laser malfuction
All elements except the Exit Fan Motor (M3) are deactivated when the
malfunctions described below are detected.
The LDVR1 signal or LDVT2 signal deviates from the specified value
while the laser power is adjusted.
LDVR1/LDVR2 : These signals are to adjust the laser drive current.
(3) Polygon motor malfunction
1. The SSCAN signal has not been entered once within 1 sec. after
the Polygon Motor is energized.
2. The number of Polygon Motor rotations has not stabilized within ±
by 4.2 sec. after the Motor is energized.
3. The number of Polygon Motor rotations has exceeded ±3% for
more than 0.5 sec. after the Motor is energized and the rotation
number stabilizes within ±0.5%.
(4) Fusing malfunction
1. The temperature detected by the Thermistor has not risen 20˚C for
50 mmsec. within 12 to 30 sec. after the warming up. (This detection applies only when the Thermistor detecting temperature is
90˚C or less.)
2. The Thermistor detecting temperature has not reached to 172˚C
within 60 sec. after warming up.
3. Except in the Pause Mode*, the Thermistor detecting temperature
during the idle state has fallen to 80˚C or lower for 50 msec., or
the temperature during printing has fallen to 133˚C or lower.
4. The Thermistor detecting temperature has exceeded 193˚C for 50
msec. during temperature control.
*Pause Mode : During this mode, the control temperature is decreased to save power during the idle state, the
Heater Lamp being turned OFF.
2 – 29
FO-5500U/C
3. Printer troubleshooting
1. PAPER JAM
(1) Paper jam occurred when the Power ON/OFF Switch (S1) is turned ON, or when the Upper Unit is closed.
Is there paper still inside the NO
machine?
YES
YES
Do the Paper Take-Up
Sensor (PC1) lever and the
Paper Exit Sensor (PC3)
lever move correctly?
Replace PC1 or PC3
Replace PWB-A.
NO
Correct the Sensor lever
movement.
Remove the paper.
(2) Paper jam occurred at the paper take-up section
Was the pa- YES Has the paper leading
edge already reached
per taken up?
the Paper Take-UP
Sensor (PC1) ?
NO
NO
YES
Does the Sensor lever
move correctly.
YES
Replace PC1 or
PWB-A.
NO
Correct the Sensor lever
movement.
Does the PaClean the Paper Takeper Take-Up YES
Up Roller and the
roller rotate?
Transport Roller.
NO
Does the Main Motor
(M1) operate?
NO
YES
Do the Paper Take-Up
Solenids (SL1)
function.
NO
YES
1. Check if the paper currently used
satisfies the specification for paper
type.
2. Check if the paper is curled,
waved,of damp.
Replace M1,the Power Unit (PWB-E) or
PWB-A.
Replace SL1 or
PWB-A.
2 – 30
FO-5500U/C
(3) Paper jam occurred at the paper transport section
Has the paper leading YES
edge alredy reached
the Fusing Roller?
NO
Has the paper
been separated
from the Fusing
Roller?
YES
NO
Clean the Pre-Image
Transfer Roller.
Does the Paper Exit
YES
Sensor (PC3) lever
move correctly?
NO
Correct the Sensor lever.
Check the Fusing
Roller and the Paper
Separator.
2. UNIT ERROR
(1) Laser malfunction
Replace PWB-A.
NG
Replace the Print Head Unit.
(2) Polygon motor malfunction
Replace PWB-A.
NG
Replace the Print Head Unit.
2 – 31
Replace PC3 or
PWB-A.
FO-5500U/C
(3) Fusing malfunction
TH1 check
Does the Heater Lamp
turn ON when the
power is ON?
YES
Is the Thermistor (TH1) YES
surface dirty?
NO
Clean TH1
NO
H1 check
Is H1 conductive?
NO
Is there electrical con- YES
ductin between
CN2 of TH1?
Replace
H1.
YES
Replace PWB-E
or PWB-A.
NO
S3 check
Is there electrical conductin between
CN2-1 and CN2-3?
NO
Replace the
Thermistat (S3)
or the Fusing Unit.
Replace TH1.
YES
Replace the Power
Unit (PWB-E) or
PWB-A.
(4) Exit fan malfunction
Does the Exit Fan Motor
(M3) rotate when the
power is ON?
YES
Replace PWB-A.
NO
NO
Replace M3.
3. OTHER TROUBLE SHOOTING
(1) No Power
Has the Power ON/OFF
Swicth been turned ON?
YES
Has the Power Cord been securely
connected to the printer?
YES
Has the Power Cord been securely
connected to the outlet?
YES
Has the fuse in the Power Unit
(PWB-E) blown?
NO
Replace PWB-E or PWB-A.
YES
Replace the fuse.
2 – 32
FO-5500U/C
[4] ERROR CODE TABLE
1. Communication error code table
G3 Transmission
Code
Final received signal
0
Incomplete signal frame
1
NSF, DIS
Error Condition (Receiver side)
Cannot recognize bit stream after flag
Cannot recognize DCS signal by echo etc.
Cannot recognize NSS signal (FIF code etc)
2
CFR
Disconnects line during reception (carrier missing etc)
3
FTT
Disconnects line by fall back
4
MCF
Disconnects line during reception of multi page
Cannot recognize NSS, DCS signal in the case of mode change
5
PIP or PIN
The line is hung up without replying to telephone request from the receiving party.
6
RTN or RTP
Cannot recognize NSS, DCS signal after transmit RTN or RTP signal.
7
No signal or DCN
No response in receiver side or DCN signal received* (transmitter side)
8
−
Owing to error in some page the error could not be corrected although the specified number of
error retransmission was at tempted.
11
−
Error occurred after or while reception by the remote (receiving) machine was revealed to be
impossible.
12
−
Error occurred just after fallback.
13
−
Error occurred after a response to retransmission end command was received.
G3 Reception
Code
Final received signal
Error Condition (Receiver side)
0
Incomplete signal frame
Cannot recognize bit stream after flag
1
NSS, DCS
Cannot recognize CFR or FTT signal
2
NSC, DTC
Cannot recognize NSS signal (FIF code etc)
3
EOP
Cannot recognize MCF, PIP, PIN, RTN, RTP signal
4
EOM
Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change
5
MPS
The line is hung up without replying to communication request.
6
PR1-Q
Cannot recognize PIP, PIN signal in the case of TALK request
7
No signal or DCN
Disconnects line during transmission (line error)
No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side)
8
−
Error occurred upon completion of reception of all pages.
9
−
Error occurred when mode was changed or Transmission/Reception switching was performed.
10
−
Error occurred during partial page or physical page reception.
11
−
Error occurred after or during inquiry from the remote (transmitting) machine as to whether
reception is possible or not.
12
−
Error occurred during or just after fallback.
13
−
Error occurred after the retransmission end command was received.
2. Service call error massage
1. HEATER ERROR
2. LASER ERROR
3. POLYGON ERROR
4. FAN ERROR
5. CPU COMM. ERROR
2 – 33
4–1
LATCH
DECODER
OPERATION
KEY
OPERATION
PANEL PWB
UNIT
TEL/LIU
PWB UNIT
LED
LCD
HANDSET
SPEAKER
TELEPHONE
LINE
MODEM
14.4Kbps
DRAM
512KB
EPROM
1MB
MAIN CPU
SH7021
LR38292
OPERATION
PANEL I/F
I/O
RECORDING
DATA CONTROL
PICTURE
DATA CONTROL
CODEC
HD813201F
LZ9FJ37A
READING
CONTROL
MECHANISM
CONTROL/
LIU PORT
PC I/F
CLOCK I/F
FLASH
MEMORY
(1MB)
SRAM
128KB
RAM
8KB x 2
RAM
2KB
DRAM
4Mbit x 3
OPTION
MEMORY
(FO-1MG/
2MG/4MG)
R. T. C.
NJU6355E
ANALOG
CIRCUIT
TLS2049
DRIVER
DRIVER
DRIVER
COMPARATOR
CONTROL PWB UNIT
PRINTER
UNIT
PCU
PRINTER
MECHANISM
LASER
UNIT
POWER
SUPPLY
UNIT
CCD PWB
VERIFICATION
STAMP
LED ARRAY
TX MOTOR
SENSOR
SCANNER UNIT
RS232C
I/F PWB
UNIT
PERSONAL
COMPUTER
FO-5500U/C
CHAPTER4. DIAGRAMS
[1] Block diagram
4–2
CN2
MAIN MOTOR
M1
PE1
3RD.
TRANSPORT
PWB
OPTION(FO-45UC)
3RD. TRANSPORT UNIT
SL3
2
5
HIGH
VOLTAGE
PWB
UNIT
PAPER
EMPTY
SENSOR
8
2
7
4
10
4
2
3
2
3
CN6
CN4
CN1
12
CN9
CN1
SL2
2
2ND. TRANSPORT UNIT
PAPER
TAKE-UP
SOLENOIDE
CN2
3
CN3
CN1
5
CN7
S2
INTERLOCK
SWITCH
2
CN4
POWER
SUPPLY
PWB
CN11
CN1
CN13
AC CORD
PRINTER
CONTROL
PWB
2ND.
TRANSPORT
PWB
CN12
CN8
CN3
CN2
CN5
CN10
CN3
PAPER
TAKE-UP
SOLENOIDE
3RD.
TRANSPORT
MOTOR
M4
PC3
PAPER EXIT
SENSOR
SL1
PAPER TAKE-UP
SOLENOID
PC1
PAPER TAKE-UP
SENSOR
TH1
THERMISTOR
LASER DIODE
DRIVE PWB
M2
POLYGON
MOTOR
PRINTER UNIT
2
1
TE1
CNH1
HEATER
LAMP
S3
THERMOSTAT
1
CN2
12P
M3
FAN MOTOR
32
CNPW
4
TONER
EMPTY
SENSOR
PERSONAL
COMPUTER
9
CNDS
CNRS
RS232C
I/F PWB
18
CNRS
CNPRT
COG
14
CNLCD
OPERATION
PANEL
PWB
CNPN
24
CNPN
CNOP
2
2
2
4
8
2
2
2
CNLIU
CNSEN
50
OPTION MEMORY
(FO-1MG/2MG/4MG)
CNROL CNSTP CNLED CNTXM CNCCD
CONTROL PWB
MAIN UNIT
CNHB
CNSP
ROLLER
SENSOR
MJ1
FRONT
SENSOR
VERIFICATION
STAMP
LED
LAMP
TX
MOTOR
CCD
PWB
DOCUMENT
SENSOR
MJTEL
TEL/LIU PWB
CNLIU
DOCUMENT
SENSOR
26
2
SPEAKER
TELEPHONE LINE
HOOK
SWITCH
PWB
FO-5500U/C
[2] Wiring diagram
CNPW
SP+
SP–
RHS
DG
SPEAKER
HOOK
SWITCH
PWB
CNHB
1
RHS
2
DG
CNHA
1
2
4–3
PRINTER
UNIT (1/2)
OGC
(LCD)
1
3
5
7
9
11
13
15
17
19
21
23
25
DG
DG
+12V
MPX B
MPX A
N.C
TEL MUTE
RCV MUTE
SIGRX
N.C
CI
N.C
N.C
A1
A3
A5
A7
A9
A11
A13
A15
B1
B3
B5
B7
B9
B11
B13
B15
PDG
PDG
PDG
PRRDY
CMD
PDG
PDG
CPRDY
PDG
PDG
PDG
EPRDY
STS
SRCLK
+5VP
+5VP
OPERATION
PANEL
PWB
POWER SUPPLY
PWB (1/2)
TEL/LIU PWB
CNSP
1
SP+
2
SP–
1
2
A2
A4
A6
A8
A10
A12
A14
A16
B2
B4
B6
B8
B10
B12
B14
B16
CN1
PDG
PCURES
HSYNC
ETBSY
PRINT
VIDEO
PDG
N.C
PDG
PDG
PDG
TOD
CTBSY
PDG
+5VP
+5VP
CNPN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
CNPN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
LD7
E
LD6
R/W
LEDEN2
RS
LEDEN1
SEN6
LD2
SEN5
LD3
SEN4
LD1
SEN3
LD4
SEN2
LD0
SEN1
LD5
SEN0
+5V
DG
+5V
DG
CNPRT
A1 PDG
A3 PDG
A5 PDG
A7 PRRDY
A9 CMD
A11 PDG
A13 PDG
A15 CPRDY
B1 PDG
B3 PDG
B5 PDG
B7 EPRDY
B9 STS
B11 SRCLK
B13 +5VP
B15 +5VP
LD7
E
LD6
R/W
LEDEN2
RS
LEDEN1
SEN6
LD2
SEN5
LD3
SEN4
LD1
SEN3
LD4
SEN2
LD0
SEN1
LD5
SEN0
+5V
DG
+5V
DG
CNPW
VM
1
VM
2
VM
3
MG
4
MG
5
MG
6
+5V
7
+5VA
8
DG
9
DG
10
+12V
11
AG
12
CNLIU
DG
1
DG
3
+12V
5
MPX B
7
MPX A
9
11 N.C
13 TEL MUTE
15 RCV MUTE
17 SIGRX
19 N.C
21 CI
23 N.C
25 N.C
CNPW
1
2
3
4
5
6
7
8
9
10
11
12
CNLIU
+5V
AG
AG
VRSEL1
VRSEL2
SPMUTE
SPOUT
SIGTX
RHS
DP
CML
N.C
N.C
VM
VM
VM
MG
MG
MG
+5V
+5VA
DG
DG
+12V
AG
2
4
6
8
10
12
14
16
18
20
22
24
26
A2
A4
A6
A8
A10
A12
A14
A16
B2
B4
B6
B8
B10
B12
B14
B16
2
4
6
8
10
12
14
16
18
20
22
24
26
PDG
PCURES
HSYNC
ETBSY
PRINT
VIDEO
PDG
N.C
PDG
PDG
PDG
TOD
CTBSY
PDG
+5VP
+5VP
+5V
AG
AG
VRSEL1
VRSEL2
SPMUTE
SPOUT
SIGTX
RHS
DP
CML
N.C
N.C
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
VBT
TCS2
MD15
MD13
MD11
MD9
MD7
MD5
MD3
MD1
MWRH
MRD
MA19
MA17
MA15
MA13
MA11
MA9
MA7
MA5
MA3
MA1
FLBK3
FLBK1
+5V
RDG
RDG
TXDA
RXDA
RTSA
CTSA
DSRA
DTRA
RSCD
RSOPT
RSCI
RDG
+5VR
RDG
+5VR
RDG
RDG
RDG
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
CNOP
DG
RAMCS
MD14
MD12
MD10
MD8
MD6
MD4
MD2
MD0
MWRL
MA20
MA18
MA16
MA14
MA12
MA10
MA8
MA6
MA4
MA2
FLBSY
FLBK2
FLOPT
DG
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
VBT
TCS2
MD15
MD13
MD11
MD9
MD7
MD5
MD3
MD1
MWRH
MRD
MA19
MA17
MA15
MA13
MA11
MA9
MA7
MA5
MA3
MA1
FLBK3
FLBK1
+5V
LEDON
VM
1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PHIT
VO
+5VA
AG
AG
PHIR
PHI1
PHI2
1
2
3
4
5
6
7
8
CNRS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
RDG
RDG
TXDA
RXDA
RTSA
CTSA
DSRA
DTRA
RSCD
RSOPT
RSCI
RDG
+5VR
RDG
+5VR
RDG
RDG
RDG
FRTS
DG
ORGS
DG
B4FRS
DG
1
2
3
4
5
6
1
VSTP
2
STPON
CNCCD2
TMA
1
TMA
2
TMB
3
TMB
4
ROLSNS
DG
1
2
CNROL
1
2
CNSEN
1
FRTS
2
DG
3
ORGS
4
DG
5
B4FRS
6
DG
CNCCD
PHIT
1
VO
2
+5VA
3
AG
4
AG
5
PHIR
6
PHI1
7
PHI2
8
CNLED
LEDON
1
VM
2
CNSTP
VSTP
1
STPON
2
CNTXM
TMA
1
TMA
2
TMB
3
TMB
4
ROLSNS
DG
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
CD
RXD
TXD
DTR
GND
DSR
RTS
CTS
CI
DG
RAMCS
MD14
MD12
MD10
MD8
MD6
MD4
MD2
MD0
MWRL
MA20
MA18
MA16
MA14
MA12
MA10
MA8
MA6
MA4
MA2
FLBSY
FLBK2
FLOPT
DG
RS232C
I/F
PWB
TX
MOTOR
VERIFICATION
STAMP
LED
CCD PWB
DOCUMENT/
FRONT
SENSOR
TRANSFER
SENSOR
OPTION
MEMORY
(FO-1MG/
2MG/4MG)
CNDS
1
2
3
4
5
6
7
8
9
PERSONAL
COMPUTER
FO-5500U/C
[3] Point to point diagram and connector signal name (1)
CONTROL PWB
(1/2)
4–4
CN3B
1
+24V
2
PK UP3
3
+5V
4
GND
5
P EMP3
6
CASSETTE
7
3RDBIN
8
LTR/LGL
9
3RD MOTOR
10 M CLOCK
1
2
3
2
1
2
1
3
2
1
1
2
8
7
6
5
4
3
2
1
THERMISTER
+5V
ANODE (PS1)
GND
PS1
+24V
FEED1
ANODE (PS3)
GND
PS3
P EMP1
GND
HV T ANA
HV T
HV SEL1
HV SEL2
HV B
BIAS MON
GND
+24V
LASER DIODE
DRIVE PWB
TH1
THERMISTER
PC1
PAPER TAKE-UP
SENSOR
SL1
PAPER TAKE-UP
SOLENOID
PC3
PAPER EXIT
SENSOR
PE1
S2 INTERLOCK
SWITCH
S3
THERMOSTAT
2ND.
TRANSPORT
UNIT
M1
MAIN MOTOR
VM
+24V
1
2
1
1
AC
CORD
CNH1
HEATER LAMP
1
2
3
4
CN1B
12
+24V
11
FEED2
10
PK UP3
9
+5V
8
GND
7
P EMP2
CASSETTE 6
5
UNIT
4
LTR/LGL
3RD MOTOR 3
2
M CLOCK
1
BIN SEL
FA
FA
FB
FB
7
6
5
4
3
2
1
S SCAN
CO
LD APC2
LD APC1
GND
L DATA
+5V
POLYGON
MOTOR
M2
HIGH
VOLTAGE
PWB
UNIT
4
3
2
1
+24V
GND
+5V
POLYGON CTL
CN2
1
2
CN4
1
2
CN3
1
2
3
CN9
1
2
3
4
5
6
7
8
9
10
11
12
AC-L
GND
AC-N
VM
+24V
HEATER N
HEATER L
+24V
FEED2
PK UP3
+5V
GND
P EMP2
CASSETTE
UNIT
LTR/LGL
3RD MOTOR
M CLOCK
BIN SEL
CN5
1
S SCAN
2
CO
3
LD APC2
4
LD APC1
5
GND
6
L DATA
7
+5V
CN2
1
THERMISTER
2
+5V
CN3
1 ANODE (PS1)
2 GND
3 PS1
4 N.C
5 +24V
6 FEED1
CN8
1 ANODE (PS3)
2 GND
3 PS3
CN12
1 P EMP1
2 GND
CN4
1
HV T ANA
2
HV T
3
HV SEL1
4
HV SEL2
5
HV B
6
BIAS MON
7
GND
8
+24V
CN6
1 FA
2 FA
3 FB
4 FB
CN10
N.C
1
+24V
2
GND
3
+5V
4
POLYGON CTL
5
PRINTER
CONTROL
PWB
CN7
1
2
3
4
5
CN15
1
2
POWER
SUPPLY
PWB
+24V
GND
GND
+5V
FUSER LAMP
PS1ZEO
+5V
CN1
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
CN13
1
+5V
2
TONER LEVER
3
TONER LED
GND
4
CN11
FAN
1
+24V
2
PDG
PDG
PDG
PCURES
PDG
HSYNC
PRRDY
ETBSY
CMD
PRINT
PDG
VIDEO
PDG
PDG
CPRDY
N.C
PDG
PDG
PDG
PDG
PDG
PDG
EPRDY
TOD
STS
CTBSY
SRCLK
PDG
+5VP
+5VP
+5VP
+5VP
CN1
1
2
3
4
5
VM
MG
DG
+5V
HEATER
PAPER
SENSOR
M3
FAN MOTOR
TE1
TONER
EMPTY
SENSOR
VM
VM
VM
MG
MG
MG
+5V
+5VA
DG
DG
+12V
AG
CNPW
1
2
3
4
5
6
7
8
9
10
11
12
FO-5500U/C
Point to point diagram and connector signal name (2)
CONTROL PWB (2/2)
FO-5500U/C
MEMO
4–5
6–1
0.1 x 6
+5V
DG
C155
A
R365
4.7K
R183 R208
0
N.M.
RES
TXD0
SCK1
RXD1
TXD1
RXD0
71
EXTAL
75
WDOVF
69
CK
76
93
94
98
95
96
DACKO
DREQO
NMI
IRQ2
IRQ3
IRQ4
IRQ6
IRQ7
PB0
PB7
PB6
PB5
PB4
PB3
PB2
PB1
B
4, 15, 24
VSS
32, 41, 50
VSS
59, 70, 81
VSS
82, 92
VSS
13, 38, 63
VCC
73, 80, 88
VCC
AD8
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
CS0
CS1/CASH
CS2
CS3/CASL
CS4
CS5/RAS
CS6
WAIT/CS7
RD
WRL
WRH
PA11
PA10
PA9/IRQOUT
PA8/BREQ
PA7/BACK
79
MD2
R210 78
4.7K 77 MD1
MD0
91
90
89
87
86
85
84
83
64
62
61
60
58
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
AD15
AD14
AD13
AD12
AD11
AD10
AD9
IC12
HD6437021
R181 72
XTAL
0
X3
19.6608MHz
R185 R212
0
R366
4.7K
R367
4.7K
R355
4.7K
DG
C139
10P
C140
DG
C141
2200P
DG
L105
33 C137
10P
N.M.
R209
4.7K
4.7K x 7
65
R206
66
R182
74
R180
67
R207
68
R214
97
R211
99
R213 100
R233
100 R236
R234 4.7K
100
N.M.
R184
DG
1
2
C173
2200P
R235
100
2200P x 4
C174
2200P
C136
1
2
CLKF
L106
0
C138
3
TELMUTE
CNLIU-13
VRSEL2
CNLIU-10
VRSEL1
CNLIU-8
SPMUTE
CNLIU-12
CML
CNLIU-22
VOLCNT
(5-5F)
MPXB
CNLIU-7
MPXA
CNLIU-9
(4-4A) VOSL1
(4-1E) VREF2
(4-2E) VREF1
(5-3F) CTSC
CNSB-36
(5-3A) CLKF
(6-6E)
(7-4A)
(5-2B) RESET2
(6-6E)
CNSB-2
DG
C172
IC118
HC08
DG
NMI
C175
3
INT2
INT3
INT4
INT6
INT7
C153
DG
(5-4E) RXIN
(5-4E) TXOUT
SRCLK
CNPRT-B11
STS
CNPRT-B9
CMD
CNPRT-A9
C171
2200P
(2-2C) RESET
(5-3B)
(6-6E)
(6-6E)
(3-3B)
(6-6E) DRQ0
CNSB-35
C151
4
5
6
B
[1] Control PWB circuit
CPU block
A
MA21
MA20
MA19
MA18
MA17
MA16
MA15
MA14
MA13
MA12
MA11
MA10
MA9
MA8
MA7
MA6
MA5
MA4
MA3
MA2
MA1
MA0
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
C
DG
R179
4.7K
N.M.
C254
C253
C261
46
47
48
49
51
52
53
54
57 R379
R380
55 0
0
56
R381
0
45
44
43
42
40
39
37
36
35
34
33
31
30
29
28
27
26
25
23
22
21
20
19
18
17
16
14
12
11
10
9
8
7
6
5
3
2
1
C
D
MWRL
MWRH
MRD
MWRL
MWRH
(5-1E) RTCIO
(5-1E) RTCCE
(5-1E) RTCCK
(5-1E) RTCDT
R296
4.7K
R297
10K
1
5
6
7
E
11
12
15
30
VSS 4
VCC 8
XT 3
DG
C205
6P
C203
0.1
VBT
F
C204
6P DG
X6
32.768kHz
+5V
C118
0.1
DG
C117
0.1
F
N.C.
N.C.
N.C.
N.C.
C105
0.1
21, 35, 40
1, 6, 20
XT 2
N.C.
N.C.
N.C.
N.C.
GND
VCC
IC106
NJU6335
I/O
CE
CLK
DATA
A8
A7
A6
A5
A4
A3
A2
A1
A0
I/O 15
I/O 14
I/O 13
I/O 12
I/O 11
I/O 10
I/O 9
I/O 8
I/O 7
I/O 6
I/O 5
I/O 4
I/O 3
I/O 2
I/O 1
I/O 0
RAS
UCAS
LCAS
WE
OE
IC7
HM514260AJ-8
26
25
24
23
22
19
18
17
16
39
38
37
36
34
33
32
31
10
9
8
7
5
4
3
2
14
28
29
13
27
(1-3D)(1-5H)(1-3H)(2-4C)(6-6D)(7-4D)
(2-5F)(2-3F)(3-3B)(5-3B)(2-1F)(10-5B)
(1-3D)(2-3F)(5-3B)(10-5B)
(2-5F)(3-3B)(5-3B)(6-6E)(7-4D)(2-1F)(10-5B)
CNSB-24
CNSB-23
CNSB-22
CNSB-21
CNOP-23
CNOP-22
CNOP-21
MRAS
(1-5D)
CS6
(5-2B)
MRD
MWRL
MWRH
WAITO
MRD
E
MA9 R146
MA8 10
R145
10
MA7 R144
MA6 10
R143
10
MA5 R142
MA4 10
R128
10
MA3 R127
MA2 10
R126
10
MA1 R125
10
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
MRAS
R124
(1-2D)
150
MCASH
R140
(1-2D)
150
R139
(1-2D) MCASL
150
R123
MWRL
(1-1D)
150
R141
(1-1D) MRD
150
MCASH
(1-5D)
CS2
(5-2B)
MCASL
(1-5D)
D
MA19
MA18
MA17
MA16
MA15
MA14
MA13
MA12
MA11
MA10
MA9
MA8
MA7
MA6
MA5
MA4
MA3
MA2
MA1
MA19
MA18
MA17
MA16
MA15
MA14
MA13
MA12
MA11
MA10
MA9
MA8
MA7
MA6
MA5
MA4
MA3
MA2
MA1
21
20
19
18
17
15
14
13
16
GND 16
VCC 32
VPP 1
CE 24
OE 22
D7
D6
D5
D4
D3
D2
D1
D0
GND
32
VCC
1
VPP
24
CE
OE 22
21
20
19
18
17
15
14
13
DG
DG
C116
0.1
+5V
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
C132
0.1
+5V
H
H
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
(2-6A)(3-6A)(10-5B)
(6-6A)(7-6D)
D7
D6
D5
D4
D3
D2
D1
D0
IC1
27C040
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
IC5
27C040
MA21~MA0
G
31
30
2
3
29
28
4
25
23
26
27
5
6
7
8
9
10
11
12
31
30
2
3
29
28
4
25
23
26
27
5
6
7
8
9
10
11
12
G
ROMCS
(5-5E)
MRD
(1-2D)
ROMCS
(5-5E)
MRD
(1-2D)
MD15~MD0
I
(2-6A)
(3-6A)
(6-6A)
(7-5A)
(10-5B)
1/10
I
1
2
3
4
5
6
FO-5500U/C
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
C152
C154
C170
6–2
1
2
3
4
5
6
B
(6-6E)
A
D102
1SS355
MANRES
DG
C131
1
+5V
(2-2C)
(5-6E)
MA20~MA0
(1-6G)
MD15~MD0
(1-6H)
R337
5.6K
1
4
C17
33/16
B
IC102
HC14
12
+5V
+12V
VBT
CNOP-1
13
R138
1K
VBT
D103
DAP202U
R338
560
(1/8W)
1
DG
2
IC102
HC14
2
3
+5V
IC103
PST591C
TCS1
FLBSY
MA20 R122 4
A20
MA19
N.M. 5 A19
6
MA18
A18
7
MA17
A17
8
MA16
A16
10
MA15
A15
11
MA14
A14
12
MA13
A13
13
MA12
A12
17
MA11
A11
18
MA10
A10
MA9
19 A9
MA8
20 A8
MA7
22 A7
MA6
23 A6
MA5
24 A5
MA4
25 A4
MA3
26 A3
MA2
27 A2
MA1
28 A1
MA0
32 A0
53 RY/BY
R168
31
BYTE
0
1
3/5
16
RP
3, 29, 30
N.C.
40
38
35
33
14
2
54
55 R167
56 100
52
50
47
45
41
39
36
34
51
49
46
44
R159
10K
R160
10K
+5V
1
3
3
Q100
DTA114EK
2
+5V
1
(5-4E)
BAT 1
CR2477-H01
C
DG
R158
4.7K
TCS2
R161
4.7K
DG
10
DG
C16
33/16
C126
0.1
C104
0.1
IC102
HC14
11
FLSTD
C125
0.1
DG
+5V
CNOP-3
TCS1 (2-3A)(2-5F)
(2-3F)(2-1F)
RESET (1-4A)
MRD
(1-2D)
MWE
(5-3B)
R166
+5V
0
Q101
DTA114EK
2
C
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
DG
C259
1
GND 21, 42, 48
VPP 15
VCC 9, 37, 43
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
CE0
CE1
OE
WE
WP
IC6
LH28F800SUT
Image memory block
A
D
D
MA16
MA15
MA14
MA13
MA12
MA11
MA10
MA9
MA8
MA7
MA6
MA5
MA4
MA3
MA2
MA1
MA16
MA15
MA14
MA13
MA12
MA11
MA10
MA9
MA8
MA7
MA6
MA5
MA4
MA3
MA2
MA1
N.C.
N.C.
N.C.
N.C.
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
N.C.
N.C.
21
20
19
18
17
15
14
13
29
22
24
GND 16
VCC 32
CS2 30
D7
D6
D5
D4
D3
D2
D1
D0
WE
CS1
OE
31
3
28
4
25
23
26
27
5
6
7
8
9
10
11
12
2
1
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
N.C.
N.C.
21
20
19
18
17
15
14
13
29
22
24
E
GND 16
VCC 32
CS2 30
D7
D6
D5
D4
D3
D2
D1
D0
WE
CS1
OE
IC3
CXK58512-10LL
31
3
28
4
25
23
26
27
5
6
7
8
9
10
11
12
2
1
IC8
CXK58512-10LL
E
C103
0.1
R118
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
DG
VBT
N.M.
R119
0
N.M.
R121
0
VBT
N.M.
R163
0
N.M.
R120
DG
C124
0.1
R162
R164
R165
0
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
F
MWRL
(1-2D)
RAMCSO
(5-5E)
MRD
(1-2D)
TCS1
(2-2C)
MWRH
(1-2D)
RAMCSO
(5-5E)
MRD
(1-2D)
TCS1
(2-2C)
F
DG
+5V
DG
DG
DG
DG
+5V
+5V
+5V
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
G
MA9
MA8
MA7
MA6
MA5
MA4
MA3
MA2
MA1
G
CNSB-3
CNSB-4
CNSB-39
CNSB-40
CNSB-37
CNSB-38
CNSB-1
CNSB-13
CNSB-14
CNSB-15
CNSB-16
CNSB-17
CNSB-18
CNSB-19
CNSB-20
CNSB-5
CNSB-6
CNSB-7
CNSB-8
CNSB-9
CNSB-10
CNSB-11
CNSB-12
CNSB-34
CNSB-26
CNSB-27
CNSB-28
CNSB-29
CNSB-30
CNSB-31
CNSB-32
CNSB-33
CNOP-2
CNOP-50
+5V
DG
DG
H
+5V
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MA7
MA6
MA5
MA4
MA3
MA2
MA1
MA15
MA14
MA13
MA12
MA11
MA10
MA9
MA8
MA20
MA19
MA18
MA17
MA16
H
DG
CNOP-49
CNOP-13
CNOP-14
CNOP-15
CNOP-16
CNOP-17
CNOP-18
CNOP-19
CNOP-20
CNOP-5
CNOP-6
CNOP-7
CNOP-8
CNOP-9
CNOP-10
CNOP-11
CNOP-12
CNOP-37
CNOP-38
CNOP-39
CNOP-40
CNOP-41
CNOP-42
CNOP-43
CNOP-29
CNOP-30
CNOP-31
CNOP-32
CNOP-33
CNOP-34
CNOP-35
CNOP-36
CNOP-24
CNOP-25
CNOP-26
CNOP-27
CNOP-28
2/10
I
I
1
2
3
4
5
6
FO-5500U/C
D104
RB411D
6–3
A
MAG
B
R115
10
R113
10
R155
10
R156
10
R175
10
R173
10
R171
10
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
R114
10
R116
10
R157
10
R154
10
R174
10
R172
10
R107
10
R105
10
R103
10
R101
10
R148
10K
R153
10K
XCLK
YCLK
EYEX
EYEY
ADIN
ADOUT
DAIN
DAOUT
C
GPO7
GPO6
GPO5
GPO4
GPO3
GPO2
36
BYPASS
40
TXLOSS1
39
TXLOSS2
38
TXLOSS3
70
71
86
90
87
35
34
88
5
4
3
2
1
100
R112
10K
RS4
RS3
RS2
RS1
RS0
D7
D6
D5
D4
D3
D2
D1
D0
RTS
CTS
TXD
DCLK
IRQ2
RXD
RLSD
54
CS
55
READ
53
WRITE
52
IRQ1
56
57
58
59
60
8
9
R102 10
10
11
R104 12
10
13
R106 14
10
15
R100
10
64
78
79
82
73
95
96
65
84
85
25
83
26
74
69
68
63
61
75
76
94
93
91
46
R108
10K
R110
10K
N.C.
N.C.
R150
10K
23, 50
6, 7, 16
66, 77, 80
81, 89, 92
97
N.C.
R151
680
19, 20, 27, 28
N.C.
29, 31, 32, 33
N.C.
41, 42, 51
N.C.
GP11
GP13
GP16
GP17
GP19
GP20
GP21
+5VA
0VD1
0VD2
0VD2
0VD2
0VD2
62
+5VD1
72
+5VD1
22
+5VD2
EN85
EYECLKX
EYECLK
ECLKIN1
EYSYNC
SYNCIN1
G2XCLK
XTLO
XTLI
C130
10P
D
N.C.
N.C.
N.C.
R109
10K
R149
10K
C100 C123
1
1
C113
1
C1
MDG MDG
C121
10P
R132
17.4K
2
MAG
N.M.
R137
+5V
+5VA
MAG
R117
0
E
L103
N.M.
+5V
6 –
5+
+12V
R131
86.6K
DG
1
– 6
+ 5
7
+12V
–2
+3
R133
118K
F
AG
C120
0.1
AG
R129
33K
R130
33K
C110
0.1
IC100
NJM2904
F
C106
0.1
IC101
NJM4558
AG
4
8
AG
4
8
C107
1000P
7
R111
86.6K
C101
1000P
IC101
NJM4558
C102
0.1
N.M.
+5V
L104
DG
R370
20 (1/8W)
C3
22/25
N.M.
E
N.M.
L101
0
L102
0
R169
L100
0
MDG
C4
3
X2 1
MAG
C108
390P
R135
0
1 C2
10/25
2
MAG MAG
C112
0.1
(5-5E)
R136
3K
MDMRST
R152
47K
DG
R134
47.5K
C109
1
MAG
C111
0.1
DG
C122
2200P
X1
38.00053MHz
49
18
48
17, 21
30, 43
47
44
TXOUT
24
SWGA I NI
99
SWGA I NO
AOUT
RAMP IN
AGD
0VA
0VA
0VA
67
PORI
37
RCVI
98
RCVO
45
RXIN
IC4
R144EFXL
D
N.M.
1
MA5
MA4
MA3
MA2
MA1
MDMCS
(5-5E)
MRD
(1-1D)
MWRH
(1-1D)
INT6
(1-5A)
MA5~MA1
MD15~MD8
C
N.M.
C129
C128
2
(1-6H)
(1-6G)
B
R170
3
4
5
6
Modem block
A
AG
C119
0.1
G
CNLIU-16
CNLIU-17
+12V
SIGTX
SIGRX
SIGRX (5-6F)
G
H
H
3/10
I
I
1
2
3
4
5
6
FO-5500U/C
6–4
CNSEN-4
A
DG
ORGS
DG
C197
2200P
C227
0.1
DG
R327
3.3K
B
6 –
7 +
4 –
5 +
1
C229
12
3
+5V
2
IC109
BA10339F
DG
N.M.
N.M.
R291
IC109
BA10339F
N.M.
R309
DG
C
C228
0.1
AVO
VREF+
DG
AG
N.M.
N.M.
+5V
10 –
11 +
8 –
9 +
D
DG
B4FRS
14
N.M.
13
N.M.
R330
DG
DG
C183
2200P
R247
270
R270
270
R331
10K
R351
10K
VREF2
VREF1
DG
E
(1-3A)
(1-3B)
23
18
19
22
16
17
15
25
26
24
R249 106
10K 107
R310 108
10K 109
R248 110
10K
A3S
B4S
FRTS
ORGS
DRSNS
TXPA
TXA1
TXA0
TXPB
TXB1
TXB0
CRNT
PLG1ON
PLG2ON
LEDON
PHIT
PHIR
PHI1
PHI2
R255
10
DG
TEST
82
SCCLK
83
SRVID
84
XSTVD
81
21, 27
GND
41, 61
GND
80, 101
GND
121, 141, 160
GND
F
116
113
114
115
112
111
117
118
119
120
122
123
124
125
F
CK16M
SCCLK1
RESET2
ADCK
HTEN
GTW
PGST
PHIBL
PHISH
B7
B6
B5
B4
B3
B2
B1
B0
RA12
RA11
RA10
RA9
RA8
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
RD15
RD14
RD13
RD12
RD11
RD10
RD9
RD8
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
ROE
RWE
126
127
128
129
130
158
157
156
155
154
153
152
151
133
134
135
136
137
138
139
140
143
144
145
146
147
148
149
150
132
131
R318
0
C225
0.1
IC15
LZ9FJ37 (1/2)
AG
+5VA
20, 62
VCC
100, 142
VCC
C180
2200P
R292
10K
R269
10K
SCCLK1
(4-1F)
SRVID R254
(6-6F)
10
STVD
(6-6F)
+5V
DG
ROLSNS
R350
IC109
BA10339F
CNROL-2
CNROL-1
IC109
BA10339F
DG
R349
C232
0.1
C245
R328
7.5K
+5V
AVO
VREF
R329
3.9K
3
2
C233
0.1
R348
0
1
CNSEN-3
R306
5.6K
C198
0.1
16 AGND
R332
11K
R333
5.1K
CNSEN-5
CNSEN-6
C184
0.1
R290
270
DG
C220
2200P
R307
10K
AG
C231
0.1
4
AG
C234
1000P
TXPA
TXA1
TXA0
TXPB
TXB1
TXB0
CRNT
STPON
PLGON
LEDON
PHIT
R250
68 105
104
R251
N.M. 103
R252
33
R253
102
33
C169
0.1
DG
R308
270
R289
10K
+5V
C11
33/16
32 AVCC
VRLM
C9
4.7/25
(9-6A)
(9-6A)
(9-6A)
(9-4A)
(9-4A)
(9-4A)
(9-2A)
(9-4E)
(9-4E)
(9-4E)
PHIT
PHIR
PHI1
PHI2
CNCCD-2
CNCCD-1
CNCCD-6
CNCCD-7
CNCCD-8
VO
C168
0.1
CNSEN-2
AG
C230
1
DG
VRHF
5
15
VO
C149
0.1
CNSEN-1
FRTS
N.M.
+5VA
L125
MMZ2012
17 DGND
VC
C223
1
R316
4.3K
C10
33/16
R373
4.7K
L124
MMZ2012
C222
0.1
1 SEL
31 DVCC
VCLP
R334
100
VSH
R335
1.6K
C8
0.47/50
C7
10/16
R311
0
6
7
8
9
14
R336
3.9K
R313
10K
E
N.M.
2
DG
L123
L122
0
PHCAP
CLPB
CLPF
SHCAP
VB
VI1– 11
12
VI2–
13
VI+
VO 10
C224
6P
D
R374
C221
N.M.
VOSL1
L121
0
+5V
30 PGST
29 B/H
28 GTW
PGST
(4-2G)
HTEN
(4-2G)
GTW
(4-2G)
(1-3A)
18 PHISH
27 PHIBL
PHISH
(4-2G)
PHIBL
(4-2G)
B6
B5
B4
B3
B2
B1
B0
19 ADCK
26
25
24
23
22
21
20
ADCK
(4-2G)
B6
B5
B4
B3
B2
B1
B0
IC22
TLS1049
C
R375
4.7K
3
4
5
6
B
Reading process block
A
+5V
RA12
RA11
RA10
RA9
RA8
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
C260
2200P
R268
270
DG
R357
4.7K
G
IC114
HC74
4
PRE
3
CLK
2
D
1
CLR
Q
6
5
(4-5B)
(4-4B)
(4-4B)
(4-4B)
(4-4B)
(4-5B)
Q~
ADCK
HTEN
GTW
PGST
PHIBL
PHISH
2
23
21
24
25
3
4
5
6
7
8
9
10
22
27
2
23
21
24
25
3
4
5
6
7
8
9
10
22
27
N.C.
ROE
RD15
(4-3G)
DG
RWE
RD14
(4-3G)
RD13
RD12
RD11
RD10
RD9
RD8
RD7
RD6
RD5
RD4
RA12
RD3
RA11
RD2
RA10
RD1
RA9
RD0
RA8
ROE (4-4H)
RA7
(4-2H)
RWE
RA6
(4-4H)
RA5
(4-2H)
B6
RA4
B5
RA3
B4
RA2
B3
RA1
B2
B1
ROE
DG
(4-3G)
B0
RWE
(4-3G)
R267
68
RA12
RA11
RA10
RA9
RA8
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
CNCCD-4
CNCCD-5
CNCCD-3
G
10
9
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
OE
WE
19
18
17
16
15
13
12
11
IC113
HC32
8
CE1 20
VSS 14
N.C. 1
CE2 26
VCC 28
D7
D6
D5
D4
D3
D2
D1
D0
19
18
17
16
15
13
12
11
CE1 20
VSS 14
N.C. 1
CE2 26
VCC 28
D7
D6
D5
D4
D3
D2
D1
D0
IC20
LH5268
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
OE
WE
IC21
LH5268
H
DG
R356
100
+5V
C196
0.1
N.C.
DG
+5V
C226
0.1
N.C.
4/10
H
I
SCCLK2 (6-6F)
N.M.
R286
R287
R288
R305
R304
R303
R302
R301
RD7
RD6
RD5
RD4
RD3
RD2
RD1
RD0
RD15
RD14
RD13
RD12
RD11
RD10
RD9
RD8
N.M.
R320
R322
R324
R326
R325
R323
R321
R319
I
1
2
3
4
5
6
FO-5500U/C
6–5
1
2
A
B
(7-1G) BZSL
(1-2D) CS2
(1-2D) CS6
DG
C134
2200P
C135
DG
C
R384
10K
DG
C266
4700P
DG
6 BZOUT
7 BZSL
56 CS2
55 CS6
40 RESET
C150
N.M.
42 CLKF
28
CLKR
A6
A5
A4
A3
A2
A1
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
RD
WRH
WRL
WR
IRQOUT
DG
R382
3K
RTCDT
RTCCLK
RTCCE
RTCIO
DP
DT4
DT3
DT2
DT1
R203
R204
R205
N.M.
D
C267
0.01
99
98
97
96
1
2
3
4
5
RHS 9
CI 10
11
HS1
12
HS2
13
EXHS1
14
EXHS2
8
SDT
DSR
DTR
RSCI
RSCD
RSOPT
N.M.
R176
0
R178
0
74
75
76
77
78
79
51
52
53
54
57
58
59
60
63
64
65
66
70
71
72
73
48
49
50
47
38
R177
10K
29
32
31
30
46
43
44
45
36
37
159
35
34
33
39
R280
4.7K
88
R279
87
4.7K
86
85
91
R278
89
R277
90
R275
92
R274
93
R273
94
R272
95
4.7K x 6
D
FLBK3
FLBK2
FLBK1
FLOPT
RAMCS1
GACCS
DG
C262
1000P
R371
0
CNSB-25
R383
51K
N.C.
N.C.
N.C.
MDMCS
(3-3B)
GABCS
(6-6E)
CDCCS1
(7-1G)(7-4D)
CNOP-44
(2-4A)
DG
L117
100
L116
100
L113
100
L111
100
RXDA
TXDA
E
BZOUT (5-6F)
RTCDT
(1-2E)
RTCCLK
(1-2E)
RTCCE
(1-2E)
RTCIO
(1-2E)
VOLB
(5-5I)
VOLA
(5-5I)
DP
DT
RCVMUTE
SDT
RHS
CI
HS1
RXIN
(1-5A)
TXOUT
(1-5A)
CTS
(5-3I)
RTSA
L115
DSRA
100
DTRA
L119
RSCI
100
RSCD
L118
RSOPT
100
L112
100
CNLIU-20
CNLIU-24
CNLIU-15
CNLIU-19
CNLIU-18
CNLIU-21
CNLIU-23
CNRS-5
CNRS-7
CNRS-8
CNRS-11
CNRS-9
CNRS-10
CNRS-4
CNRS-3
RAMCS0
(2-5F)(2-3F)(2-1F)
MDMRST
(3-6E)
ROMCS
(1-5H)(1-3H)
FLSTD
(2-4C)
CNOP-48
CNOP-4
FLBSY
E
FLBSY
CNOP-45
CNOP-46
CNOP-47
C206
C207
C208
C209
C211
C212
C213
C214
(2-2C) RESET2
(1-4A) CLKF
(6-1F)(7-3D) CK16M
(1-1D)
(1-1D)
(1-1D)
(2-4C)
(1-5A)
MRD
MWRH
MWRL
MWE
INT2
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
MA6
MA5
MA4
MA3
MA2
MA1
FLBSY
FLBK3
FLBK2
FLBK1
GABSL
CDCSL
GACSL1
GACSL0
SRAM1
SRAM0
MDMRST
PGMSL
FLSTD
FLOPT
REVSL
RXIN
TXOUT
RXOUT
TXIN
CTS
RTS
IC15
LZ9FJ37 (2/2)
MA21 69 A21
MA20 68 A20
MA19 67 A19
C
F
(1-3A)
(3-6G)
(5-1D)
F
+5V
CNRS-6
(1-3A)
AG
1
2
3
5
9
10
3
16
DG
L120
0
L110
0
CTSA
6
INHBT
7
VEE
8
VSS
VDD
IC110
4053
DG
1
11
IC110
4053
R354
22K
12
13
CTSC
1Y
0Y
1Z
0Z
B
C
VOLCNT 2
Q103
DTC114
+12V
SIGRX
BZOUT
AG
14
G
RDG
RDG
RDG
RDG
RDG
RDG
RDG
+5VR
+5VR
L114
100
C235
0.1
CNRS-1
CNRS-2
CNRS-12
CNRS-14
CNRS-16
CNRS-17
CNRS-18
X0
X1
X2
X3
X4
X5
X6
X7
VDD
N.M.
DG
C210
H
H
IC105
4051
7
VEE
8
VSS
6
INHBT
13
14
15
12
1
5
2
4
16
R276
4.7K
AG
C202
0.1
AG
R295
360K
CNRS-13
CNRS-15
+5V
R293
75K
R294
16K
+12V
C201
0.1
G
DG
5
4
IC118
HC08
9
10
11
6
I
DG
(5-2E)
(5-2E)
I
CTS (5-4E)
AG
VOLB
VOLA
CNLIU-14
5/10
R271
3 6.2K SPOUT
C200
1000P
3
MD15~MD0
MA21~MA19, MA6~MA1
Gate array (A) block
B
C199
1000P
4
5
6
A
1
2
3
4
5
6
FO-5500U/C
6–6
B
N.M.
GND
GND
GND
GND
RAS0B
RAS1B
CASB
DWEB
DRMTYPE
DRMSIZE
TEST
MEMTST
VCC
VCC
VCC
VCC
GND
GND
GND
GND
GND
RSTCDCB
RDCDCB
RDCDC
SHCKOB
CK16M
DRQO
CDCINT
READY
MDENB
MAS
MAENB
BACKB
BRQT
MAD0
MAD1
MAD2
MAD3
MAD4
MAD5
MAD6
MAD7
MAD8
MAD9
MAD10
MAD11
MAD12
MAD13
MAD14
MAD15
MA16
MA17
MA18
MA19
MA20
DA0
DA1
DA2
DA3
DA4
DA5
DA6
DA7
DA8
DA9
DA10
DA11
R189
33
R191
33
R193
33
R195
33
R197
33
R222
R298
100
R190
33
R194
33
R192
33
R196
33
R223
R198
33
C167
E
F
RSTCDC (7-3D)
RDCDC (7-3A)
RDCDC (7-4A)
CLKF (7-4A)
CK16M (7-3D)
DRQO (7-1H)
CDCINT (7-4D)
READY (7-2H)
MDEN (7-3H)
MAS (7-3H)
MAEN2 (7-1D)
BACK1 (7-2A)
BRQT (7-3H)
PMAD0
PMAD1
PMAD2
PMAD3
PMAD4
PMAD5
PMAD6
PMAD7
PMAD8
PMAD9
PMAD10
PMAD11
PMAD12
PMAD13
PMAD14
PMAD15
PMA16
PMA17
PMA18
PMA19
PMA20
DRA0
DRA1
DRA2
DRA3
DRA4
DRA5
DRA6
DRA7
DRA8
DRA9
D
DG
C252
0.1
20
62
100
142
21
61
101
143
CNPRT-A6
DG
134
125
99
114
113
115
112
105
102
109
108
110
111
104
103
117
118
119
120
121
122
123
124
126
127
128
129
130
131
132
133
135
136
137
138
139
144
145
146
147
148
149
150
151
152
153
154
155
C
87
38
37
36
34
33
32
31
30
29
28
27
39
DG
19
22
23
1
2
3
4
5
6
7
8
21
20
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
WE
OE
24
17
16
15
14
13
11
10
9
18
CS
12
GND
VCC
I/O 8
I/O 7
I/O 6
I/O 5
I/O 4
I/O 3
I/O 2
I/O 1
IC19
LH5116NA-10
G
DG
R261
2.2K
C193
2200P
HSYNC
DG
C258
0.1
DG
DG
R284
560
C179
0.1
C192
10P
+5V
58
PRINT
57
CTBSY
60
CPRDY
53
EPRDY
R260
3.3K R259 PRRDY
54
55
TOD
R258 3.3K
3.3K R257
56
ETBSY
51
R372 3.3K PCURES
1K
52
HSYNC1
59 R285
VIDEO
270
C219
C194
63
XIN
N.M.
DG
64
DG
XOUT
PRINTB
CTBSYB
CPRDYB
EPRDYB
PRRDYB
TODB
ETBSYB
PCURESB
HSYNC
PDATA
GND
LMA10
LMA9
LMA8
LMA7
LMA6
LMA5
LMA4
LMA3
LMA2
LMA1
LMA0
LMWEB
LMD0
GND
A
DG
16
35
48
78
158
157
159
156
141
140
50
49
IC16
LR38292
DG
G
C251
0.1
(7-6H) PMA20~PMA16, PMAD15~PMAD0
(8-6A)
(8-6A)
DRA9~DRA0
C166
DG
N.M.
DG
R242
270
C161
DG
R220
C164
+5V
H
R283
1M
H
6
5
4
3
IC102
HC14
IC102
HC14
DG
C191
10P
C218
3
CNPRT-B14
CNPRT-B13
CNPRT-B16
CNPRT-B15
1
C217
X7
R299
DG
I
HSYNC1 (6-3H)
DG
2
IC108
CNPRT-A2,A1
CNPRT-A3
CNPRT-B4
CNPRT-A5
CNPRT-B5,B1,B2
CNPRT-B6,B3
CNPRT-A11
CNPRT-B12
CNPRT-A13
CNPRT-A14
N.M.
IC108
DG
R300
4
R282
CNPRT-A12
R342
PDG
PDG
PDG
PDG
PDG
PDG
PDG
PDG
PDG
PDG
I
6/10
+5VP
+5VP
+5VP
+5VP
N.M.
+5V
R345
R346
R343
R344
CNPRT-A10
CNPRT-B10
CNPRT-A15
CNPRT-B7
CNPRT-A7
CNPRT-B8
CNPRT-A8
CNPRT-A4
DG
C195
0.1
LMD7
LMD6
LMD5
LMD4
LMD3
LMD2
LMD1
LMD0
X5
22.24044MHz
1
C165
R221
N.M.
C163
PMRAS0
PMRAS1
PMCAS
GAPMW
R230
470
R228
470
R225
R246
270
R243
270
R264
270
C160
2200P x 8
R232
470
R231
470
R229
470
R227
470
R226
470
R244
270
R245
270
R241
270
R262
270
R263
270
67
STVDB
68
SRVID
69
SCCLK
2
(8-1A)
(8-1A)
(8-1A)
(8-1A)
CNPN-8
CNPN-10
CNPN-12
CNPN-14
CNPN-16
CNPN-18
CNPN-20
N.C.
N.M.
N.M.
LD15
LD14
LD13
LD12
LD11
LD10
LD9
LD8
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
SEN7
SEN6
SEN5
SEN4
SEN3
SEN2
SEN1
SEN0
RESETB
MANRESB
CDCINTB
GAINTB
SHCK1
CSCDCB
DACKOB
DREQOB
CSB
WRB
RDB
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
A1
A2
A3
A4
A5
SEN6
SEN5
SEN4
SEN3
SEN2
SEN1
SEN0
LD7
LD6
LD5
LD4
LD3
LD2
LD1
LD0
R239
R240
R224
26
25
24
23
22
19
18
17
15
14
13
12
11
10
9
8
160
1
2
3
4
5
6
7
N.M.
C190
2200P
C188
C189
F
LMD1
LMD2
LMD3
LMD4
LMD5
LMD6
LMD7
3
4
CNPN-1
CNPN-3
CNPN-19
CNPN-15
CNPN-11
CNPN-9
CNPN-13
CNPN-17
N.C.
N.C.
N.C.
R266
270
DG
MA1
MA2
MA3
MA4
MA5
3K
R265
C269
1
+5V
MD5
MD6
MD7
MD8
MD9
MD10
MD11
MD12
MD13
MD14
MD15
66
65
94
95
116
107
106
96
88
98
97
86
85
84
83
82
81
80
79
77
76
75
74
73
72
71
70
93
92
91
90
89
LEDEN2
LEDEN1
RS
R/W
E
+5V
+5V
DG
DG
E
RESET2
MANRES
INT4
INT3
CLKF
CDCCS2
DACKO
DRQO
GABCS
MWRH
MRD
MD0
MD1
MD2
MD3
MD4
47
46
45
44
43
42
41
40
CNPN-5
CNPN-7
CNPN-6
CNPN-4
CNPN-2
CNPN-21
CNPN-23
CNPN-22
CNPN-24
MA5~MA1
MD15~MD0
D
(1-4A)
(2-2A)
(1-5A)
(1-5A)
(1-4A)
(7-1H)
(7-1G)(7-4D)
(1-5A)
(5-5E)
(1-1D)
(1-1D)
(1-6G)
(1-6G)
C
STVD
(4-2E)
SRVID
(4-2E)
SCCLK2
(4-1H)
LMD0
LMD1
LMD2
LMD3
LMD4
LMD5
LMD6
LMD7
5
6
B
Gate array (B) block
A
1
2
3
4
5
6
FO-5500U/C
N.C.
N.C.
C162
6–7
1
(7-3H)
(7-3H)
(7-3H)
(6-1F)
MAS
A
MAEN1
BRQT
BACK1
13
IC112
HC04
11
9
12
RDCDC
IC112
HC04
(6-1F)
CLKF
(1-4A)
RDCDC
(6-1F)
(1-6G)
10
8
+5V
MD15~MD8
R358
4.7K
B
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
B
10
PRE
11
CLK
12
D
13
CLR
Q~ 8
Q 9
IC117
HC74
Q~ 6
Q 5
19
16
15
12
9
6
5
2
20
10
N.C.
9
10
C
8
C187
0.1
IC115
HC08
13
12
CD7
CD6
CD5
CD4
CD3
CD2
CD1
CD0
CD7
CD6
CD5
CD4
CD3
CD2
CD1
CD0
+5V
+5V
C215
0.1
DG
DG
IC115
HC08
N.C.
GND
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
VCC
2
4
6
8
11
13
15
17
20
GND 10
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
VCC
IC104
LS244
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
1 1G
19 2G
18
16
14
12
9
7
5
3
IC117
HC74
4
PRE
3
CLK
2
D
1
CLR
D7
D6
D5
D4
D3
D2
D1
D0
11 CK
1 OE
18
17
14
13
8
7
4
3
IC107
LS374
C
11
(6-1F)
(7-3H)
D
MAEN2
BACK2
(6-1F)
(5-3B)
(7-2G)
(6-6E)
(6-1F)
C177
2200P
RSTCDC
C147
30P
DG
X4
16MHz
DG
C146
30P
CK16M
DRQT
DACKO
CDCINT
CDCCS1
MWRH
RDCDC
(1-6G) MA3~MA1
(5-5E)
(1-1D)
(6-1F)
D
R188
0
L108
0
+5V
E
DG
C178
1
GND
VCC
7
14
C268
1
C145
1000P
R187
10K
DG
R219
33
R238
4.7K
MA3
MA2
MA1
IC117
HC74
CD7
CD6
CD5
CD4
CD3
CD2
CD1
CD0
+5V
E
C144
100P
2
3
4
5
6
Codec block
A
D7
D6
D5
D4
D3
D2
D1
D0
DG
29
49
72
10
17
34
53
70
75
18
22
24
33
43
C250
0.1
+5V
VDD1
VDD2
VDD3
VSS1
VSS2
VSS3
VSS4
VSS5
VSS6
TEST0
TEST1
TEST2
TEST3
TEST4
59 RESET
CLKO
CLKI
CLKX
CLKMOD
CKTST2
CKTST1
CKTST0
56 68/80
21
19
20
40
80
1
41
F
GND
VCC
IC115
HC08
52
48
76
74
25
27
23
26
28
35
36
9
12
7
8
4
6
2
5
78
3
77
79
51
50
31
30
11
71
16
15
13
14
7
14
DG
C247
0.1
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
+5V
RTCH 60
61
RTCL
READY 73
39
DRQTI
38
DACKO
DMA 32
DTC 37
BRQT
BACK
MAEN
MAS
MDEN
UDS
LDS
MR
MW
IOR
IOW
MA21
MA20
MA19
MA18
MA17
MA16
MA/MD15
MA/MD14
MA/MD13
MA/MD12
MA/MD11
MA/MD10
MA/MD9
MA/MD8
MA/MD7
MA/MD6
MA/MD5
MA/MD4
MA/MD3
MA/MD2
MA/MD1
MA/MD0
IC14
HD813201F
47 DRQTO
46 DACKI
58 IRQT
44
CS
42
R/W
45
DS
69
68
66
67
63
65
62
64
55
A2
54
A1
57
A0
F
DG
R218
0
(6-6E)
(5-5E)
(5-2B)
R361
4.7K
R359
4.7K
N.M.
5
4
DACKO
2
1
6
IC115
HC08
3
IC115
HC08
R360
4.7K
CDCCS1
BZSL
H
H
READY
CDCCS2
DRQO
(6-1F)
I
I
(6-6E)
(6-1F)
(7-2A)(6-1E)
(7-2D)
(7-1A)
(7-1A)
(6-1F)
(6-1B)
7/10
CDCMW (8-1A)
UDS (8-6G)
LDS (8-6G)
BRQT
BACK2
MAEN1
MAS
MDEN
PMA19~PMA16, PMAD15~PMAD0
DRQT
DG
(7-4D)
C159
G
PMA20
PMA19
PMA18
PMA17
PMA16
PMAD15
PMAD14
PMAD13
PMAD12
PMAD11
PMAD10
PMAD9
PMAD8
PMAD7
PMAD6
PMAD5
PMAD4
PMAD3
PMAD2
PMAD1
PMAD0
G
1
2
3
4
5
6
FO-5500U/C
6–8
1
2
3
4
5
6
B
A
(7-3H) CDCMW
(6-3A) PMRAS1
(8-5I) PMUCAS
(6-2A) GAPMW
(6-3A) PMRAS0
(8-5I) PMLCAS
R199
10
R200
10
R201
10
R202
100
R364
100
(6-1B) DRA11~DRA0
(6-1B) PMAD15~PMAD0
B
Page memory block
A
N.C.
DRA9
DRA8
DRA7
DRA6
DRA5
DRA4
DRA3
DRA2
DRA1
DRA0
N.C.
DRA9
DRA8
DRA7
DRA6
DRA5
DRA4
DRA3
DRA2
DRA1
DRA0
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
N.C.
RAS
CAS
WE
I/O 7
I/O 6
I/O 5
I/O 4
I/O 3
I/O 2
I/O 1
I/O 0
N.C.
VCC
VCC
OE
VSS
VSS
27
26
25
24
5
4
3
2
21
1
14
22
15
28
9
20
19
18
17
16
13
12
11
10
6
8
23
7
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
N.C.
RAS
CAS
WE
C
27
26
25
24
5
4
3
2
21
1
14
VCC
22
OE
15
VSS
28
VSS
I/O 7
I/O 6
I/O 5
I/O 4
I/O 3
I/O 2
I/O 1
I/O 0
N.C.
VCC
IC9
HM514800AJ-8
9
20
19
18
17
16
13
12
11
10
6
8
23
7
IC11
HM514800AJ-8
C
N.C.
N.C.
DG
C127
0.1
+5V
PMAD7
PMAD6
PMAD5
PMAD4
PMAD3
PMAD2
PMAD1
PMAD0
DG
C148
0.1
+5V
PMAD15
PMAD14
PMAD13
PMAD12
PMAD11
PMAD10
PMAD9
PMAD8
D
D
DRA8
DRA7
DRA6
DRA5
DRA4
DRA3
DRA2
DRA1
DRA0
DG
N.C.
N.C.
N.C.
N.C.
26
25
24
23
22
19
18
17
16
11
12
15
30
14
28
29
13
27
A8
A7
A6
A5
A4
A3
A2
A1
A0
N.C.
N.C.
N.C.
N.C.
RAS
UCAS
LCAS
WE
OE
E
I/O15
I/O14
I/O13
I/O12
I/O11
I/O10
I/O9
I/O8
I/O7
I/O6
I/O5
I/O4
I/O3
I/O2
I/O1
I/O0
VCC
VCC
VCC
VSS
VSS
VSS
2
1
6
20
21
35
40
4
3
39
38
37
36
34
33
32
31
10
9
8
7
5
IC10
HM514260AJ-8
E
DG
C133
0.1
+5V
PMAD15
PMAD14
PMAD13
PMAD12
PMAD11
PMAD10
PMAD9
PMAD8
PMAD7
PMAD6
PMAD5
PMAD4
PMAD3
PMAD2
PMAD1
PMAD0
F
F
(7-3H)
(6-2A)
(7-3H)
(7-3H)
MAEN1
PMCAS
UDS
LDS
G
4
5
2
1
IC113
HC32
G
6
3
1A
1B
2A
2B
3A
3B
4A
4B
H
GND
VCC
4Y
3Y
2Y
1Y
IC116
HC157
15
G
1
S
2
3
5
6
11
10
14
13
H
18
16
12
9
7
4
DG
PMUCAS
PMLCAS
C256
0.1
+5V
N.C.
N.C.
N.M.
R363
R362
8/10
I
(8-1A)
(8-2A)
I
1
2
3
4
5
6
FO-5500U/C
6–9
A
R237
100K
C
2
1
3
DG
3
2
1
IC100
NJM2904
Q102
2SC2413K
C157
0.1
+5V
(9-1D)
VM
CNTXM-3
CNTXM-4
(9-1D)
VM
CNTXM-1
CNTXM-2
D
TMVR (9-3D)
(9-5D)
TMVR
TMB
F2
CCP2E30
TMB
TMVR
F1
CCP2E30
TMA
TMA
D
STPON
C114
0.1
(4-4E)
R377
1K
R376
R378
4.7K
DG
7
14
1
MG
AG
+12V
DG
DG
+5V
+5VA
MG
MG
MG
VM
VM
VM
2
N.C.
AG
DG
R339
0
F
C239
0.1
N.M.
R5
R6
91 (1/2W)
MG
1
13
11
9
5
MG
VM
C236
0.1
3
2
N.M.
MG
3 N.M.
D101
Q105
2SD1164
MG
C216
0.1
DG
Q104 2
1
+12V
3
Q106
2SD1164
10
IC102
HC14
N.M.
9
+5V
F
C243
0.1
C14
33/16
C15
47/25
E
CNPW-12
CNPW-11
CNPW-9
CNPW-10
CNPW-7
CNPW-8
CNPW-4
CNPW-5
CNPW-6
CNPW-1
CNPW-2
CNPW-3
LEDON
(4-4E) PLGON
(4-4E)
+5V
E
C241
0.1
B
NOTE:
These marks are all safety-critical parts.
DG
VR
VCC
GND
GND
GND
GND
N.M.
R216
180K
R215
200K
+5V
16 E
R217
1K
+5V
D2
1
2
(4-4E)
CRNT
N.M.
N.M.
R1
0.47
R368
R2
C156
820P
N.M.
MG
C158
D1
11
6
4
5
12
13
C142
0.1
L107
C186
0.1
DG
MG
D106
MG
MG
10 C
2 T
VMM 3
VMM 14
MA 15
MB 1
11
6
4
5
12
13
C5
47/50
C143
820P
R186
56K
8 PH
9 I0
7 I1
IC13
PBL3717/2
16 E
R281
1K
VR
VCC
GND
GND
GND
GND
C181
0.1
N.M.
D4
3
4
N.M.
R3
0.47
R369
N.M.
R4
C185
820P
10 C
2 T
VMM 3
VMM 14
MA 15
MB 1
N.M.
MG
MG
C182
820P
R256
56K
8 PH
9 I0
7 I1
L109
C6
47/50
TXPB
(4-5E)
TXB0
(4-5E)
TXB1
(4-5E)
TXPA
(4-5E)
TXA0
(4-5E)
TXA1
(4-5E)
IC17
PBL3717/2
C176
D3
5
6
Driver & Supply block
C
D108
D107
–
B
D109
12
10
8
6
AG
+12V
DG
G
G
GND
VCC
N.M.
R340
C12
22/10
N.M.
F4
7
14
7
14
DG
DG
VM
VPLG
DG
DG
DG
H
H
R347
HB-H3216A
R147
HB-H3216A
CNLIU-4
CNLIU-6
+12V
CNLIU-1
CNLIU-3
+5V
+5VA
CNLED-2
CNPLG-1
CNSTP-1
C248
0.1
+5V
C249
0.1
+5V
N.C.
N.C.
N.C.
DG
VSTP
IC118
HC08
GND
VCC
IC114
HC74
6
5
2
4
7
IC112
14 HC04
3
1
F3
CCP2E20
CNLED-1
CNPLG-2
CNSTP-2
DG
C246
0.1
C237
0.1
+5V
AG
2
1
VM
LEDON
IC111
78L5UA
R341
0
(1/8W)
3
STPON
N.C.
N.C.
N.C.
N.C.
+5V
PLGON
D105
1SS355
D100
1SS355
VM
7
14
IC108
HCU04
C242
0.1
+
A
FG
AG
AG
+12V
11
8
IC118
HC08
+5V
13
12
10
9
Q
7
14
AG
I
CNLIU-5
CNLIU-2
N.C.
N.C.
N.C.
N.C.
C257
0.1
+5V
N.C.
DG
DG
Q~
IC114
HC74
GND
VCC
IC113
HC32
11
IC113
12
PRE
11
CLK
10
D
13
CLR
13
12
9/10
I
1
2
3
4
5
6
FO-5500U/C
C244
0.1
C13
33/16
6 – 10
A
D150
RB411D
B
DG
+5V
MA7
MA6
MA5
MA4
MA3
MA2
MA1
MA0
+5V
MA17
MA18
MA19
MA20
MA21
DG
C263
DG
C264
C
IC24
GND
GND
D08
D07
D06
D05
D04
D03
D02
D01
VCC
VCC
IC23
GND
GND
D08
D07
D06
D05
D04
D03
D02
D01
VCC
VCC
D16
D15
D14
D13
D12
D11
D10
D09
D16
D15
D14
D13
D12
D11
D10
D09
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
DG
+5V
E
+5V
MD7
MD6
MD5
MD4
MD3
MD2
MD1
MD0
F
DG
MA15
MA16
MA17
MA18
MA19
MA20
IC25
GND
GND
D08
D07
D06
D05
D04
D03
D02
D01
VCC
VCC
D16
D15
D14
D13
D12
D11
D10
D09
N.M.
19
18
17
16
15
14
13
12
G
D142
D143
MD11
D144
MD12
MD13
D145
D146
MD14
MD15
D147
D125
D126
D127
D128
D129
D130
MA21
D131
MD2
MD3
MD4
MD5
MD6
MD7
D124
MA6
MA7
MA8
MA9
MA10
MA11
MA12
MA13
F
9
8
7
6
5
4
3
2
1
20
C265 10
11
MD10
MD1
D117
D119
D120
D121
D122
D123
D
MA15
MA14
MA13
MA12
MA11
MA10
MA9
MA8
MA16
E
MD9
D134
G
MD0
D118
MA0
MA1
MA2
D112
MA3
D113
MA4
D115
RB411D x 22
N.M.
19
18
17
16
15
14
13
12
19
18
17
16
15
14
13
12
MA14
D141
C
9
8
7
6
5
4
3
2
1
20
10
11
9
8
7
6
5
4
3
2
1
20
10
11
D
DG
MD15
MD14
MD13
MD12
MD11
MD10
MD9
MD8
D140
1
+5V
(1-2D) MRD
(1-2D) MWRH
(1-2D) MWRL
(1-6G) MA21 ~ MA0
(1-6H) MD15 ~ MD0
B
MD8
2
3
4
5
6
Other block
A
+5V
N.M.
H
H
10/10
I
I
1
2
3
4
5
6
FO-5500U/C
D132
D133
D135
D136
D137
D138
D139
D116
D110
D111
D114
MA5
D149
RB411D
D148
RB411D
FO-5500U/C
Control PWB parts layout (Top side)
6 – 11
FO-5500U/C
Control PWB parts layout (Bottom side)
6 – 12
6 – 13
1
A
MJTEL-3
MJTEL-2
CNLIU-15
AG
RX–
RX+
L7
SBT0260
B
C13
4.7/50
E
Q105
DTC114
C
E
D103
1SS355
AG
L6
D102
SBT0260 1SS355
B
Q103
DTC114
B
C
E
VRSEL2
RCVMUTE
5
3
N.M.
N.M.
JP1
R141
1K
2
1
C
AG
R136
150
C115
220P
AG
R137
2.2K
R138
3.3K
AG
AG
L2
3 Z2089
4
+12V
AG
R143
1K
C116
1000P
Q109
C2412K
R114
22K
R102
22K
R113
22K
VREF
R115
22K
N.M.
C114
1
AG
C12
4.7/50
IC102
BU4066B
4
AG
Q101
DTC114
C
E
Q104
DTC114
B
C
C113
R135
1K
B
C112
2200P
L8
SBT0260
VREF
R140
330
L3
SBT0260
VA1
TNR7G471K
ARG ARG
VA2
TNR7G471K
AR1
VRSEL1
TELMUTE
TX –
TX +
RING
TIP
JP2
– 6
5
+
D
AG
12
6
R112
8.2K
R118
15K
R117
24K
11
+12V
E
R120
22K
R116
39K
IC102
BU4066B
8
IC102
BU4066B
R144
8.2K VREF
10
9
13
2
7
C107
1000P
R125
22K
3
B
M
10
R119
18K
R127
22K
R126
22K
R129
22K
4
AG
F
AG
Q110 E
DTC114
B
VREF
VREF
R105
11K
D104
1SS355
7
R133
51K
C111
330P
E
1
ZD2
HZS2C1
G
R131
620
C7
4.7/50
R130
620
AG
Q102
DTC114
C
B
IC105
NJM4558
6 –
5 +
C16
0.01
L4
LAL04TB102K
CI
PC2
TLP521-1
1
G
L5
LAL04TB102K
IC105
NJM4558
2 –
3 +
R106
27K
C104
330P
ZD1
HZS2C1
R134
15K
+12V
R123
100K
VREF
2
N.M.
R5
ZD3
HZ27-A
R122
22K
R4
22K
(1/2W)
R3
22K
Q106
C2412K
R146
27K
R124
22K
+12V
C15
0.82
F
R121
680 C
IC103
BU4066B
+5
– 6
5
12
9
IC103
BU4066B
11
8
6
5
4
IC103
BU4066B
CML
OUAZ-SS-124L
C
VREF
1
IC104
NJM4558
PC1
TLP627
DP
E
R111
10K
3
2 ~ – 1
REC1
S1ZB60
4
3 ~ + 4
IC102
BU4066B
1
C10
2.2/50
IC106
1
R142
68K
IC106
NJM4558
7
R139
47K
C118
1000P
C120
1000P
3 +
2 –
C119
1000P
R1
100 (1/2W)
R2
47 (1W)
D
AG
MPXA
MPXB
H
CNLIU-7
H
IC106
NJM4558
CNLIU-17
AG
4
8
+12V
8
I
IC105
NJM4558
4
C105
0.1
AG
14
I
IC102
BU4066B
7
C109
0.1
1/2
AG
1
N.C.
2
N.C.
IC103
BU4066B
C117
0.1
AG
7
13
C108
0.1
14
C8
4.7/50
CNLIU-9
CNLIU-16
AG
ZD4
HZS2C1
ZD5
HZS2C1
4 C121
0.033
SIGTX
2
T1
Z2128
3
1
SIGRX
AG
R128
750
CNLIU-10
CNLIU-8
CNLIU-13
MJTEL-4
MJTEL-1
MJ1-2
MJ1-1
L1
SBT0260
C
C11
2.2/50
C110
0.033
2
3
4
5
6
B
[2] TEL/LIU PWB circuit
A
1
2
3
4
5
6
FO-5500U/C
6 – 14
1
2
3
4
5
6
B
A
CNLIU-3
CNLIU-1
CNLIU-2
CNLIU-6
CNLIU-4
CNLIU-5
CNLIU-14
C103
0.1
DG
AG
B
4
2
3
C101
0.1
C
7
8
–
5
AG
4
8
+12V
6
C4
47/25
C3
47/25
1
C
IC101
NJM2113M
3 +
2
C102
0.1
C2
1/50
N.M.
AG
R103
10K
DG
1
C106
1000P
R107
75K
IC104
NJM4558
C6
4.7/50
DG
R101
R104
10K
AG
C14
4.7/50
R110 R109
3.3K
SPOUT 0
R108
100K
+5V
TEL/LIU PWB circuit
A
N.M.
+12V
AG
DG
+5V
AG
C1
SPMUTE
SP–
SP+
DG
C5
47/25
VREF
CNLIU-12
CNSP-2
CNSP-1
D
D
+12V
+5V
R145
10K
PC2
TLP521-1
CI
CML
3
DG
E
DP
PC1
TLP627
1
2
CNH A-2
CNH A-1
C9
0.33/50
D101
1SS355
2
DG
3
4
R132
220
HOOK SW
E
DG
E
DG
AG
E
DG
F
C
Q111
DTC114
Q108
DTC114
B
C
B
E
Q107
DTC114
B
C
CNH B-2
CNH B-1
F
TP1
CML
CI
DP
RHS
G
CNLIU-22
CNLIU-21
CNLIU-20
CNLIU-18
G
1
3
5
7
9
11
13
15
17
19
21
23
25
TX+
RX+
RX–
TX–
RHS
DG
H
DG
DG
+12V
MPX B
MPX A
N.C.
TEL MUTE
RCV MUTE
SIGRX
N.C.
CI
N.C.
N.C.
CNLIU
1
2
3
4
MJTEL
1
2
CNH B
H
2
4
6
8
10
12
14
16
18
20
22
24
26
1
2
MJ1
1
2
TIP
RING
SP+
SP–
+5V
AG
AG
VRSEL1
VRSEL2
SPMUTE
SPOUT
SIGTX
RHS
DP
CML
N.C.
N.C.
CNSP
2/2
I
I
1
2
3
4
5
6
FO-5500U/C
FO-5500U/C
TEL/LIU PWB parts layout
6 – 15
A
PC702
S21ME4FY
6 – 16
C
R712
47K
D705
1SS178
D
R711 R714
15K
68
4
3
2
1
B
1
R717
150
HEATER N
D704
RD20ES
IC701
FA5315P
C709
220P
3
R713
10K
C708
0.047
5
6
7
8
1
X703
ENC471D10
R709
33K
R707
0.22 (1W)
F702
127°C
2
X702
ENC471D10
R710
82
R703
39
C713
0.001
D706
RD30ES
C724
10000P
R706
0.22 (1W)
R705
39K
TH701
D702
ERA1501
R704
39K
C711
0.1
D703
ERA9102
L704
R715
1K
R708
39 (1W)
C707
47/35
Q701
2SK2543
E
PC701
TLP621
C723
4700P
C722
4700P
C706
100P
T701
C714
1000P
C715
680/35
D707
YG901C2
L706
F
F
FE
R720
100K
C719
330/35
IC703
PQ1CG1
L707
IC702
UPC1093J-1
R718
1K
R725
1K
D709
D2S4M
HEATER L
CN2
X701
ENC241D10
C712
0.1
R701
330K
C725
1000P
D701
D3SB60Z
C705
560/200
R726
39K
R702
10K
TR701
C703
470P
C704
470P
L702
E
C716
680/35
R716
22
C701
0.1
FE
L701
D
R719
1K
3
3
1
F701
6.3A/125V
C702
0.047
AC-N
CN3
AC-L
S701
C
PC701
S21ME4FY
4
5
6
B
[3] Power supply PWB circuit
A
R722
2.55K
G
PC702
S21ME4FY
R724
1K
R723
3K
IC704
NJM7812FA
L705
D708
1SS178
C721
330/35
C718
22/35
F704
4A/125V
F703 INTERLOCK SW
4A/125V
C720
330/35
L708
C717
0.47/50
R721
22K
G
H
HEATER
ON/OFF
DG
+5V
AG
MG
+12V
VM
+24V
H
VM
+24V
1
2
3
4
5
6
7
8
9
10
11
12
VM
VM
VM
MG
MG
MG
+5V
+5V
DG
DG
+12V
AG
I
HEATER ON/OFF
VM
MG
DG
+5V
CNPW
1
2
CN4
1
2
3
4
5
CN1
1/1
I
1
2
3
4
5
6
FO-5500U/C
C710
0.0047
Q702
2SA1015
FO-5500U/C
Power supply PWB parts layout
6 – 17
6 – 18
1
A
CNPN-24
CGND
C12
B
N.M.
C
D
16
1
14
13
11
6
4
3
9
CGND
GND VDD
CLR
6D
6D
5D
5D
4D
4D
3D
3D
2D
2D
1D
1D
CLK
CNPN-22
8
CNPN-23
15
12
10
7
5
2
2
+5V
150 x 7
8
2
7
6
1
3
4
5
C11
2200P
C5
33/16
+5V
IC4
HC174
CNPN-21
GND
E
C10
0.1
R12
100K
16
1
14
13
11
6
4
3
9
3
9
15
10
11
16
14
13
12
C6
2200P
LED9 (DRUM)
LED10 (SRVICE)
LED1 (H-TONE)
LED2 (S-FINE)
LED3 (FINE)
LED4 (STD)
LED6 (IN-USE)
Q2
DTC114ES
R10
100K
DG
Q1
DTC114ES
15
12
10
7
5
2
IC3
HC174
IC2
ULN2003
+5V
LED7 (PAPER)
LED8 (TONER)
N.M.
LEDEN1
LEDEN2
LD0
LD1
LD2
LD3
LD4
LD5
LD6
LD7
RS
R/W
E
E
R/W
RS
SEN6
SEN5
SEN4
SEN3
SEN2
SEN1
SEN0
DG
DG
R14
R13
R1
R2
R3
R4
R7
Q3
GND VDD
CLR
6D
6D
5D
5D
4D
4D
3D
3D
2D
2D
1D
1D
CLK
CNPN-7
CNPN-5
CNPN-17
CNPN-13
CNPN-9
CNPN-11
CNPN-15
CNPN-19
CNPN-3
CNPN-1
CNPN-6
CNPN-4
CNPN-2
2
4
6
8
10
12
14
16
18
20
22
24
E
8
4
LD7
LD6
LEDEN2
LEDEN1
LD2
LD3
LD1
LD4
LD0
LD5
+5V
+5V
+5V
D
R5
150
R11
150
1
3
5
7
9
11
13
15
17
19
21
23
CNPN
C
R6 LED5 (LINE)
5
6
B
[4] Operation panel PWB circuit
A
DG
F
+5V
F
G
G
C8
220P
J37
1
3
5
7
9
11
13
J26
C7
33/16
+5V
VSS
VO
R/W
DB0
DB2
DB4
DB6
CNLCD
R9
150
2
4
6
8
10
12
14
H
R8
2.4K
H
VO
VDD
VSS
I
CNLCD-1
CNLCD-3
CNLCD-2
CNLCD-7
CNLCD-8
CNLCD-9
CNLCD-10
CNLCD-11
CNLCD-12
CNLCD-13
CNLCD-14
CNLCD-4
CNLCD-5
CNLCD-6
LD0
(2-2A)
LD1
(2-2A)
LD2
(2-2A)
LD3
(2-2A)
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
RS
R/W
E
C4
4.7/25
VDD
RS
E
DB1
DB3
DB5
DB7
1/2
I
1
2
3
4
5
6
FO-5500U/C
C9
22/16
C3
22/16
6 – 19
1
2
3
4
5
6
B
A
LD0
(1-4I)
LD1
(1-4I)
LD2
(1-4I)
LD3
(1-4I)
C1
2200P
SEN6
SEN5
SEN4
SEN3
SEN2
SEN1
SEN0
+5V
C2
33/16
CNPN-8
CNPN-10
CNPN-12
CNPN-14
CNPN-16
CNPN-18
CNPN-20
B
15
14
13
12
8
16
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
IC1
LS145
A
B
C
D
GND
VDD
1
2
3
4
5
6
7
9
10
11
Operation panel PWB circuit
A
C
7
4
1
Y
Q
I
A
C
8
5
2
Z
R
J
B
9
6
3
SPACE
S
K
C
D
D
REDIAL
SPEED
DIAL
FUNCTION
SHIFT
T
L
D
B’ CAST
COPY
SP
U
M
E
V
N
F
E
0
SHEET
COVER
REPORT
CLEAR
E
#
PRIORITY
DOCUMENT
W
O
G
F
SPEAKER
START
STOP
X
P
H
F
RESOLU-
TION
CHANGE-
OVER
LINE
SW-A
G
G
H
H
2/2
I
I
1
2
3
4
5
6
FO-5500U/C
FO-5500U/C
Operation panel PWB parts layout
6 – 20
6 – 21
1
2
3
4
5
6
B
CNCCD-5
CNCCD-4
CNCCD-3
A
B
CCD PWB parts layout
[5] CCD PWB circuit
A
AG
AG
+5VA
R1
0
C
C1
22/25
C
C2
0.1
AG
D
CNCCD-2
+5V
D
VO
CNCCD-6
CNCCD-1
CNCCD-8
CNCCD-7
Q1
A1037K
VO
AG
PHIT
PHI2
PHI1
E
R2
2.2K
E
AG
C1
0.1
AG
F
F
1
2
3
4
5
6
7
8
9
10
11
NC
NC
VDD
NC
NC
NC
NC
NC
Φ TG
NC
NC
NC
NC
AGND
VOUT
NC
NC
NC
Φ2
Φ1
DGND
NC
IC1
µPD3753CY
22
21
20
19
18
17
16
15
14
13
12
G
G
H
H
1
2
3
4
5
6
7
8
PHIT
VO
+5VA
AG
AG
AG
PHI1
PHI2
CNCCD
I
I
1
2
3
4
5
6
FO-5500U/C
6 – 22
A
B
C
RSOPT
RDG
+5VR
RDG
D
+5V
8
C4
0.1/50
C1
0.1/50
L7
L2
L4
L3
L1
L8
L5
L6
RDG
RDG
+5V
C6
0.1
E
RXD
CTS
DSR
CD
CI
TXD
RTS
DTR
CNDS-5
CNDS-2
CNDS-8
CNDS-6
CNDS-1
CNDS-9
CNDS-3
CNDS-7
CNDS-4
1
3
5
7
9
11
13
15
17
CNRS
RDG
RXDA
CTSA
DSRA
RSCD
RSCI
+5VR
+5VR
RDG
F
2
4
6
8
10
12
14
16
18
F
RDG
TXDA
RTSA
DTRA
RSOPT
RDG
RDG
RDG
RDG
1
2
3
4
5
6
7
8
9
CNDS
G
CD
RXD
TXD
DTR
GND
DSR
RTS
CTS
CI
G
H
H
1/1
I
I
3
4
5
6
1
14
11
15
9
10
12
13
20
24
3
2
1
16
4
23
21
19
6
7
18
17
5
22
E
1
CNRS-1
CNRS-2
CNRS-12
CNRS-14
CNRS-16
CNRS-17
CNRS-18
CNRS-13
CNRS-15
CNRS-10
C5
0.1/50
C2
0.1/50
IC1
ADM207
D
2
RXDA
CTSA
DSRA
RSCD
RSCI
TXDA
RTSA
DTRA
C
2
CNRS-3
CNRS-5
CNRS-7
CNRS-9
CNRS-11
CNRS-4
CNRS-6
CNRS-8
[6] RS232C I/F PWB circuit
B
C3
22/50
3
4
5
6
A
FO-5500U/C
FO-5500U/C
RS232C I/F PWB parts layout (Top side)
RS232C I/F PWB parts layout (Bottom side)
6 – 23
FO-5500U/C
Printer control PWB parts layout
Printer 2nd transport PWB parts layout
6 – 24
FO-5500U/C
PARTS GUIDE
MODEL
FO-5500
CONTENTS
1
Exterior, etc. (1)
12 Fusing unit
2
Exterior, etc. (2)
13 2nd transport unit
3
Operation panel unit
14 Cassette
4
Document guide upper unit
15 Packing material & Accessories
5
Optical unit
16 Control PWB unit
6
Drive unit
17 TEL-Liu PWB unit
7
Scanner frame unit
18 Power supply PWB unit
8
Housing
19 RS232C I/F PWB unit
9
Drive/Paper take-up unit (1)
20 CCD PWB unit
10 Paper take-up unit (2)
11 Transfer unit
50 Hardware parts
Index
Because parts marked with " " is indispensable for the machine safety maintenance and operation, it must be
replaced with the parts specific to the product specification.
FO-5500U/C
1
Exterior, etc. (1)
B14
35
B10
36
13
B14
38
B14
8
B9
B14
B10
15
57
31
16
B14
2
58
W2
33
34
B14
30
B16
32
B10
B10
17
B9
B10
B14
B9
PRINTER
UNIT
B11
41
3
B9
B10
B14
54
SCANNER
UNIT
B10
B12
4
20
52
53
50
B11
10
19
B14
W2
B11
B11
B11
42
12
55
B11
B12
21
B11
2ND
TRANSPORT
UNIT
B11
28
23
40
6
B11
B11
B11
B5
B11
B11
14
B15
B11
46
B11
51
B11
B11
B11
B11
45
B11
27
B11
B11
B11
B4
1
B11
25
48
B13
B11
43 B11 B11
22
B11
B13
62
B1
59
B11
60
18
49
37
26
24
44
5
B11
61
20
100mm
80mm
37
–1–
B11
37
B1
FO-5500U/C
Exterior,, etc.(1)
1
NO.
1
2
3
4
5
6
8
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
30
31
32
33
34
35
36
37
38
40
41
42
43
44
45
46
48
49
50
51
52
53
54
55
57
58
59
60
61
62
PARTS CODE
CCNW-4276XH01
CCNW-4557SC01
CSW-M2222SC01
DCEKC582HSCZZ
DCEKI497ASC01
DCEKL494ASC01
GCABL2272SCZZ
GCABR2273SCZZ
GCOVA2363SCZZ
GCOVA2364SCYZ
GCOVA2367SCZZ
GCOVA2371SCZZ
GDAI-2074SCZZ
GDAI-2075SCZZ
GFTAF2110SCZZ
GMADZ2024SCZZ
LBNDJ2007SCZZ
LHLDW1006FCZZ
LHLDW2156SCZZ
LHLDW2157SCZZ
LPLTM2806SCZZ
LPLTM2807SCZZ
LPLTM2808SCZZ
LPLTM2809SCZZ
LPLTM2810SCZZ
LPLTP2811SCZZ
LPLTP2812SCZA
MLEVP2229SCZZ
MSPRC2856SCZZ
NGERP2287SCZZ
PGIDP2454SCZZ
PGIDP2455SCZZ
PGUMS2135SCZZ
PHOP-2091SCZZ
PSHEZ3225SCZZ
QCNW-4558SCZZ
QCNW-4559SCZZ
QCNW-4563SCZZ
QCNW-4564SCZZ
RDENT2095SCZZ
LHLDW2158SCZZ
PHOG-2073SCZZ
LPLTM2856SCZZ
LPLTM2854SCZZ
QCNW-4668SCZZ
LHLDW0004SCZZ
RCORF2064SCZZ
RCORF2094SCZZ
RCORF7009XCZZ
TLABH4066SCZZ
PSHEZ3267SCZZ
PTME-2051SCLZ
PTME-2051SCRZ
LBNDJ2006SCZZ
PCAPH2020SCZZ
PRICE
RANK
AU
AM
AE
CN
BC
BD
AW
AW
AQ
AT
AK
AL
AK
AE
AC
AF
AA
AA
AC
AC
AY
AT
AU
AX
AG
AY
AL
AE
AC
AC
AG
AF
AC
AU
AF
AE
BA
AP
AS
BR
AC
AF
AG
AK
AC
AB
AE
AE
AR
AC
AF
AE
AE
AA
AT
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
C
B
E
E
E
D
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
C
C
C
C
C
C
B
B
B
D
C
C
C
C
C
DESCRIPTION
AC cord
Speaker ass’y
Paper sensor ass’y
Control PWB unit(Within ROM)
RS232C I/F PWB unit
TEL-Liu/hook switch PWB unit
Left side panel
Right side panel
Printer front cover
Scanner cover
Power supply PWB cover
ROM cover
Handset cover, top
Handset cover, bottom
I/F cap
Hopper window
Band(80mm)
Mini clamp(UAMS-09-0)
Edge holder
Wire holder
Bottom plate
Left side chassis
Right side chassis
Top plate
Printer bracket
Inner tray
Paper setting plate
Hook switch lever
Hopper spring
Pinion gear
Hopper guide, right
Hopper guide, left
Foot
Hopper
TEL-Liu PWB sheet
Paper sensor cable
Printer cable
Power cable
I/F cable
Power supply PWB unit
Wire holder
Edging
Bottom plate braket, top
TEL-Liu PWB bracket
Earth cable
Clamp
Core
Core
Core
Paper setting plate label
Inner tray sheet
Cassette lock plate, left
Cassette lock plate, right
Band(100mm)
Connector cap
–2–
FO-5500U/C
2
Exterior, etc. (2)
1
3
B10
B10
B10
6
B10
B10
4
2
4
4
B10
B10
5
B8
B8
3
5
3
9
4
13
10
13
12
8
2
7
6
11
1
14
B17
B17
B17
–3–
FO-5500U/C
Exterior,, etc.(2)
2
NO.
PARTS CODE
1
2
3
4
5
6
CCASP2083SC51
PGIDP2459SCZZ
PGLS-2057SCZZ
PSHEZ3254SCZZ
LBNDJ2007SCZZ
PSHEZ3262SCZZ
PRICE
RANK
BQ
AS
AF
AC
AA
AC
NEW
MARK
N
N
N
N
N
PART
RANK
E
C
C
C
C
C
Document guide lower
Reader glass
Dustproof sheet
Band
Document guide lower sheet
PRICE
RANK
BC
AT
AK
AK
AH
AE
AE
AE
AE
AF
AU
BA
AC
AC
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
E
D
C
C
C
C
C
C
C
C
C
B
C
C
Operation panel PWB unit
Panel case
Decoration panel
12 key
Direct key
Start key
Stop key
Mode key
Change key
Page plate
Panel cable
LCD
LCD cushion
Panel sheet
BQ
N
E
DESCRIPTION
3
NO.
PARTS CODE
DCEKP496ASC01
GCASP2083SCZZ
HPNLC2370SCZZ
JBTN-2184SCZZ
JBTN-2185SCZZ
JBTN-2186SCZZ
JBTN-2187SCZZ
JBTN-2188SCZZ
JBTN-2189SCZZ
LPLTP2823SCZZ
QCNW-4554SCZZ
VVLLMG2025TPR
PCUSS2097SCZZ
PSHEZ3270SCZZ
(Unit)
901 CCASP2083SC51
1
2
3
4
5
6
7
8
9
10
11
12
13
14
DESCRIPTION
–4–
FO-5500U/C
4
B7
B7
11
20
3
B7
8
13
10
4
10
16
2
21
15
19
14
1
5
1
9
12
20
17
21
6
18
5
7
Optical unit
12
4
B12
8
11
12
8
11
2
5
3
B12
B12 10
7
9
B6
6
13
B12
1
B2
6
Drive unit
3
8
1
5
6
B3
B8
7
4
B3
–5–
2
FO-5500U/C
4
NO.
PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
LBSHP2067SCZZ
LPLTG2820SCZZ
LPLTM2822SCZZ
LPLTP2819SCZZ
LPLTP2821SCZZ
MLEVP2230SCZZ
MSPRC2843SCZZ
MSPRC2844SCZZ
MSPRC2845SCZZ
MSPRC2867SCZZ
MSPRP2846SCZZ
NGERH2327SCZZ
NROLP2300XHZZ
NROLR2336SCZZ
NSFTZ2263SCZZ
PBRS-2047SCZZ
PGIDP2456SCZZ
PSHEZ3205SCZZ
PSHEZ3249SCZZ
QCNW-4560SCZZ
LBNDJ2007SCZZ
PRICE
RANK
AC
AH
AF
AD
AD
AG
AC
AA
AC
AB
AD
AC
AC
AM
AD
AG
AT
AD
AC
AD
AA
NEW
MARK
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Bearing
Separator rubber
Reinforcement bracket
Separator plate
Transfer plate
Release lever
Release lever spring
Separate spring
Paper feed pressure spring
Pinch roller spring
Earth plate spring 4
Transfer roller gear
Pinch roller
Transfer roller
Pinch roller shaft
Electro-static discharger brush
Document guide upper
Rear sheet
Separator sheet
Electro-static discharger cable
Band
PRICE
RANK
AZ
AF
AG
AF
AF
AC
AY
AL
AC
AL
AC
AE
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
E
C
C
C
C
C
C
C
C
C
C
B
CCD PWB unit
Lens holder plate
Lens holder
Mirror hold plate, left
Mirror hold plate, right
Lens holding spring
Lens
Mirror
Shading sheet
CCD cable
Mirror lock sheet
Core
PRICE
RANK
AQ
AC
AD
AD
AE
AD
AC
BF
NEW
MARK
N
PART
RANK
C
C
C
C
C
C
C
B
Motor plate
Reduction gear(14/50)
Idler gear 70
Idler gear 45
Slowdown gear
Electro-static discharger cable
Earth cable
Transfer motor
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DESCRIPTION
Optical unit
5
NO.
PARTS CODE
1
2
3
4
5
6
7
8
9
10
12
13
6
DCEKD495ASC01
LANGH2803SCZZ
LHLDP2155SCZZ
LPLTP2832SCZA
LPLTP2833SCZA
MSPRP2842SCZZ
PLNS-2050SCZZ
PMIR-2073SCZZ
PSHEZ3204SCZZ
QCNW-4555SCZZ
PSHEZ3263SCZZ
RCORF2063SCZZ
DESCRIPTION
Drive unit
NO.
PARTS CODE
1
2
3
4
5
6
7
8
LPLTM2834SCZZ
NGERH2239SCZZ
NGERH2324SCZZ
NGERH2326SCZZ
NGERH2330SCZZ
QCNW-4560SCZZ
QCNW-4668SCZZ
RMOTZ2124SCZZ
N
N
N
N
N
N
DESCRIPTION
–6–
FO-5500U/C
7
Scanner frame unit
5
W1
17
21
20
14
34
23
5
5
B8
28
22
2
24
1
18
B8
30
5
3
5
16
19
13
10
B8
12
15
31
33
9
B11
11
6
31
29
26
26
B8
35
8
B8
4
7
B8
B8
8
Housing unit
11
23
3
22
4
21
22
5
19
22
6
22
–7–
17
FO-5500U/C
Scanner frame unit
7
NO.
PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26
28
29
30
31
33
34
35
CBSHP2079SC01
CROLP2300SC01
CSW-M2222SC01
LBSHC2084SCZZ
LBSHP2066SCZZ
LFRM-2167SCZZ
LPLTM2813SCZZ
LPLTM2814SCZZ
MSPRP2838SCZZ
MSPRP2839SCZZ
MSPRP2840SCZZ
MSPRP2841SCZZ
MSPRP2850SCZZ
NGERH2177SCZZ
NGERH2319SCZZ
NGERH2320SCZZ
NGERH2322SCZZ
NGERH2323SCZZ
NROLR2337SCZZ
NROLR2338SCZZ
NROLR2339SCZZ
NSFTZ2260SCZZ
NSFTZ2261SCZZ
NSFTZ2262SCZZ
PSHEZ3208SCZZ
PSTM-2015SCZZ
QCNW-4562SCZZ
QCNW-4612SCZZ
QSW-Z2236SCZZ
QSW-Z2237SCZZ
VHPSNL14A70-1
PCUSU2101SCZZ
PRICE
RANK
AK
AF
AE
AC
AC
AW
AK
AK
AC
AD
AD
AC
AD
AC
AC
AD
AC
AD
AH
AK
AM
AG
AH
AE
AC
AX
AK
AE
AE
AE
BC
AC
NEW
MARK
N
N
PRICE
RANK
AQ
BC
AG
AG
BH
AF
AL
AF
AB
AE
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
C
DESCRIPTION
Paper feed clutch unit
Pinch roller
Transfer sensor ass’y
Bushing
Bearing
Scanner frame
Scanner frame bracket, front
Scanner frame bracket, rear
Stopper spring
Pinch roller spring 2
Transfer gear 1
ADF transfer gear
Transfer idler gear
ADF paper feed gear
Paper feed gear
Transfer roller
Paper feed roller
Transfer roller 1
Paper feed roller shaft 1
Paper feed roller shaft 2
Pinch roller shaft
Dustproof sheet
Verification stamp
Document/Front sensor cable
Transfer sensor cable
Front sensor
Document sensor
LED
Scanner frame cushion
Housing
8
NO.
3
4
5
6
11
17
19
21
22
23
PARTS CODE
0KW0992180302
0KW0997610201
0KW0992231002
0KW0992230413
0KW0992180102
0KW0992100601
0KW0992180401
0KW0992180501
0KW9739030813
0KW0992180701
N
N
N
N
N
N
N
PART
RANK
C
B
C
C
C
C
C
C
C
C
DESCRIPTION
Duct
Fan motor
Cover
Cover
Top cover
Actuator
Lock lever
Torsion spring
Screw
Sheet
–8–
[M3]
FO-5500U/C
9
Drive/Paper take-up unit (1)
72
9
57
68
1
10
67
74
76
3
8
2
71
72
4
7
70
75
5
75
72
23
18
24
13
20
21
21
71
66
76
65
22
20 74
62
75
62
78
70
19
76
72
15
17
26
63
55
16
35
27
28
32
42
75
73
30
54
44
49
34
37
58
39
71
37
53
36
33
31
29
52
64
25
43
38
46
60
61
70
40
–9–
51
70
41
48
47
70
FO-5500U/C
Drive/Paper take-up unit(1)
9
NO.
1
2
3
4
5
7
8
9
10
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
46
47
48
49
51
52
53
54
55
57
58
60
61
62
63
64
65
66
67
68
70
71
72
73
74
75
76
77
78
PARTS CODE
0KW0992230712
0KW0992011903
0KW0992200512
0KW0992200117
0KW0992202301
0KW0992232012
0KW0992280102
0KW0992241402
0KW0992280201
0KW0992230514
0KW0992301012
0KW0992301901
0KW0992301502
0KW0992230825
0KW0992300802
0KW0992300901
0KW0992304001
0KW0992302902
0KW0992231314
0KW0992300124
0KW0992250301
0KW0992250401
0KW0992250213
0KW0992250512
0KW0992200412
0KW0992203401
0KW0992610401
0KW0992250102
0KW0992250701
0KW0992251401
0KW0992250601
0KW9335141031
0KW0992301401
0KW0992301102
0KW0992621213
0KW0992350301
0KW0992350205
0KW0992301804
0KW0992300601
0KW0992303505
0KW0992304101
0KW0992075101
0KW0992302202
0KW0992350102
0KW0992410112
0KW0992300202
0KW1200123602
0KW0992302112
0KW0992605202
0KW0992203301
0KW9383251011
0KW0992305201
0KW0992231101
0KW0956202701
0KW0992203801
0KW0992242301
0KW0992281201
0KW0992280301
0KW0992012102
0KW0992606801
0KW9742030813
0KW9735030613
0KW9739030813
0KW9646030813
0KW9770030813
0KW9735030813
0KW9733031413
0KW9721040001
0KW0992280401
PRICE
RANK
AP
CA
AQ
BG
AD
AD
AX
AD
AQ
AF
AG
AF
AD
AH
AF
AD
AC
AM
AF
AQ
AG
AG
AH
AH
AL
AQ
BF
AL
AG
AF
AF
BA
AD
AD
AV
AD
AN
AD
AD
AF
AC
BB
AF
AR
AP
AR
AC
AF
AL
AC
AD
AC
AC
AF
AD
AF
AH
AF
AX
AQ
AB
AB
AB
AB
AC
AC
AB
AB
AE
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
E
C
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
B
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
C
C
B
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Bracket
Printer control PWB
Right frame
Base
Ground plate
Plate nut
Frame
Ground plate
Rear frame
Bracket, switch
Gear 40T
Clutch spring
Holder
Cover
Cam
Bushing
Pin
Shaft
Frame
Roller, Take-up
Gear 50T
Gear 22/45T
Gear 25/72T
Gear 29/65T
Left frame
Heat-sink
Motor
Gear 44/109T
Gear 22/57T
Gear 29T
Gear 20/41T
Photo interrupter
Bushing
Gear 16T
Solenoid
Ground plate
Holder
Torsion spring
Roll
Holder, Roll
Pressure spring
Separator, Take-up
Stopper
Guide
Guide
Roller, Transport
Washer
Actuator
Harness
Edge cover
Connector
Washer
Shoulder screw
Rubber foot
Seal
Label
Mounting plate
Grommet
Microswitch ass’y
Harness
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Washer
Wiring saddle
– 10 –
[PWB-A]
[M1]
[PC1]
[SL1]
[S2]
FO-5500U/C
10 Paper take-up unit (2)
54
7
1
5
6
4
3
54
47
38
2
58
48
55 32
11
10
8
42
27
51
9
31
49
12
29
30
50
53
16
28
10
13
15
46
10
25
57
24
56
17
41
44
37
14
10
22
21
57
20
18
19
23
54
56
33
11 Transfer unit
1
3
2
23
20
24
9
5
4
5
6
22
21
4
23
7
18
10
24
17
16
6
8
15
11
12 14
13
25
23
– 11 –
19
FO-5500U/C
10 Paper take-up unit(2)
NO.
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
24
27
28
29
30
31
32
33
37
38
41
42
44
46
47
48
49
50
51
53
54
55
56
57
58
PARTS CODE
0KW0992053306
0KW0992200701
0KW0992200603
0KW0992201201
0KW0992605601
0KW0997621204
0KW0992044301
0KW0992605413
0KW0992201902
0KW0992202014
0KW0992202101
0KW0992241302
0KW0992241202
0KW0992305036
0KW0992304513
0KW0992300601
0KW0992320701
0KW0992605501
0KW0992320102
0KW0992300701
0KW0992301603
0KW0992302401
0KW0992202401
0KW0992300301
0KW0992310401
0KW0992075201
0KW0992302501
0KW0992201304
0KW0992202202
0KW0992231101
0KW9384131111
0KW0992606101
0KW0992305301
0KW0992305501
0KW0992320801
0KW0910362001
0KW0997605201
0KW0997630101
0KW0997231203
0KW0957010101
0KW0997605101
0KW0992380301
0KW9739030813
0KW9735030813
0KW9735030613
0KW9742030813
0KW9735031213
PRICE
RANK
CA
AD
AF
AD
AN
BV
AS
AQ
AF
AD
AC
AF
AF
AD
AD
AD
AF
AU
AG
AD
AD
AN
AD
AF
AL
AZ
AD
AD
AF
AC
AC
AN
AC
AG
AC
AC
AM
AN
AH
AZ
AL
AF
AB
AC
AB
AB
AB
NEW
MARK
PRICE
RANK
AL
AV
AD
AE
AD
AD
AF
AV
BA
AD
AH
AG
BQ
AG
AS
BL
AG
AC
AH
AC
AF
AH
AB
AB
AB
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
E
C
C
C
C
E
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
E
C
C
C
C
C
C
C
DESCRIPTION
Print head unit
Terminal
Terminal
Terminal
Harness
High voltage PWB unit(with IC)
Cover
Harness
Guide
Guide
Bracket, Print head
Plate spring
Plate spring
Plate spring
Holder, Roll
Roll
Sheet
Harness
Guide plate
Support
Pressure spring
Holder
Ground plate
Lever
Cover
Lifting plate
Cam
Torsion spring
Ground plate
Shoulder screw
Cable tie 104L
Harness
Plate
Sponge
Polyester film
C-Ring
Harness
Photo interrupter
Holder
Laser diode drive PWB
Harness
Sheet
Screw
Screw
Screw
Screw
Screw
[PWB-F]
[PWB-G]
11 Transfer unit
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PARTS CODE
0KW0992381501
0KW0992010224
0KW0992371101
0KW0957321501
0KW0992370901
0KW0992370701
0KW0957320801
0KW0992382001
0KW0992075901
0KW0992420712
0KW0992421001
0KW0992420601
0KW0992039101
0KW0992420512
0KW0992420301
0KW0992420101
0KW0992421301
0KW0992421402
0KW0992420412
0KW0992420812
0KW0992380101
0KW0992380202
0KW9739030813
0KW9739030613
0KW9742030813
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
E
C
C
C
C
C
C
C
C
C
C
E
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Ground plate
Resistor PWB(NO IC)
Ground plate
Bushing
Holder
Roll
Gear 15T
Roller
Holder
Torsion spring
Ring
Gear 21T
Transfer unit
Bushing
Guide plate
Roller
Plate
Pressure spring
Bushing
Torsion spring
Gear 20T
Holder
Screw
Screw
Screw
– 12 –
[PWB-R]
FO-5500U/C
12 Fusing unit
2
33
36 33 34
2
35
37
38
33
27
39
40
44 12
10
3
41
21
20
41
8
4
9
5
6
42
19
11
13
41
22
42 41
23
41
28 29 41
19 23
42
31
30 45
15
26
43
41
25
24
18
41
16
7
32
17
15
14
12 Fusing unit
NO.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
PARTS CODE
0KW0992101703
0KW0992180203
0KW0992255202
0KW0992255101
0KW0992255001
0KW0992250813
0KW0992250901
0KW0992251301
0KW0992251212
0KW0992251112
0KW0992251001
0KW0992048303
0KW0992401503
0KW0972553101
0KW0992551201
0KW0992552101
0KW0992553103
0KW0992551713
0KW0992606604
0KW0992552401
0KW0992563401
0KW0957551101
0KW0992554001
0KW0992554101
0KW0992671501
0KW0992562601
0KW0992671301
0KW0992562501
0KW0992553201
0KW0992650501
0KW0992580602
0KW0992553303
0KW0957552702
0KW0992370601
0KW0992551801
0KW0992551901
0KW9335141031
0KW0992605301
0KW0992731201
0KW9739030813
0KW9646030613
0KW9733031013
0KW0992180601
0KW0992554501
PRICE
RANK
AC
AY
AF
AC
AF
AG
AF
AC
AF
AD
AN
CD
AH
AE
AL
AH
AF
AC
AQ
AD
AD
AK
BF
BR
AZ
AN
BB
AQ
AD
BE
BT
AH
AF
AF
AD
AC
BA
AG
AF
AB
AB
AB
AE
AU
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
E
C
C
C
C
C
C
C
C
C
C
C
C
B
C
B
C
C
B
C
C
C
C
C
C
B
C
D
C
C
C
C
C
DESCRIPTION
Pin
Cover
Holder
Torsion spring
Arm
Gear 20/50T
Gear 44T
Torsion spring
Lever
Gear 22T
Gear 21/38T
Fusing unit
Guide
C-Ring
Gear 30T
Bushing
Frame-LFT
Pressure spring
Harness
Terminal
Bracket
Bushing
Fusing roller-UPR
Fusing roller-LWR
Thermistor
Terminal
Thermostat
Terminal
Frame-RT
Tube lamp
Holder
Separator
Separator roll
Gear 40T
Actuator
Torsion spring
Photo interrupter
Harness
Label
Screw
Screw
Screw
Sheet
Bushing
– 13 –
[TH1]
[S3]
[H1]
[PC3]
FO-5500U/C
13 2nd transport unit
35
1
4
2
32
37
41
6
6
3
2
5
37
42
7
34
11
40
13
33
37
37
9
31
36
7
19 4017
20
16
40
30
13
12 40
40
14
39
29
26
15
37
36 39
13
26
26
18
40
40
23
40
28
27
27
13
37
13 2nd Transport unit
NO.
1
2
3
4
5
6
7
9
11
12
13
14
15
16
17
18
19
20
23
26
27
28
29
30
31
32
33
34
35
36
37
39
40
41
42
PARTS CODE
0KW4150181301
0KW0933384002
0KW0933382612
0KW4150180201
0KW4150180103
0KW4150184501
0KW4150184601
0KW4150180901
0KW4150182001
0KW0928300602
0KW1200312003
0KW4150183201
0KW0928301902
0KW4150183101
0KW4150183301
0KW4150620101
0KW4150102902
0KW0957251103
0KW4150020201
0KW0992304001
0KW4150104301
0KW4150181901
0KW4150183602
0KW4150181703
0KW4150182201
0KW4150010103
0KW4150181001
0KW4150180303
0KW9742030813
0KW9742031013
0KW9743030813
0KW9646040813
0KW9721040001
0KW4150184701
0KW9384131091
PRICE
RANK
AG
AF
AH
AX
AU
AD
AD
AP
AV
AG
AD
AF
AL
AG
AF
BT
AH
AG
AX
AC
AR
AP
AH
AN
AL
BS
AP
AY
AB
AB
AB
AC
AB
AF
AC
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
E
C
C
C
C
C
C
C
C
C
DESCRIPTION
Plate spring
Roll
Shaft
Guide
Guide
Sheet
Sheet
Pin
Roller
Gear 14T
Bushing
Boss
Clutch spring
Holder
Gear 18T
Solenoid
Gear 13/45T
Gear 41T
Mounting plate
Pin
Roller
Shaft
Actuator
Plate spring
Cover
2nd. bin PWB
Pin
Frame
Screw
Screw
Screw
Screw
Washer
Sheet
Clamp
– 14 –
[PWB-B]
FO-5500U/C
14 Cassette
2
2
1
13
3
15
14
17
5
6
4
14
10
12
20
4
18
11
8
22
7
18
16
15
19
21
14 Cassette
NO.
1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
18
19
20
21
22
PARTS CODE
0KW4150180702
0KW4150180801
0KW4150181801
0KW4150182402
0KW0933392201
0KW0933390202
0KW4150182503
0KW4150181502
0KW0933390302
0KW0933392301
0KW4150182701
0KW4150731301
0KW9739030813
LX-BZ0175FCZZ
MLEVP2242SCRZ
MLEVP2242SCLZ
PSPAZ0584FCZZ
MSPRC2888SCZZ
MSPRC2889SCZZ
TLABH4065SCZZ
0KW4150182801
PRICE
RANK
BA
AD
AQ
AL
AN
AT
BK
AN
AT
AN
AH
AF
AB
AB
AF
AF
AA
AC
AD
AD
AE
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
D
C
C
C
C
C
C
C
D
C
DESCRIPTION
Lifting plate
Pad
Lever
Pressure spring
Separator
Regulating plate
Cassette body
Guide
Regulating plate
Separator
Guide
Label
Screw
Screw
Cassette lock lever, right
Cassette lock lever, left
Plate nut
Lever rturn spring, right
Lever rturn spring, left
Lever label
Guide
– 15 –
FO-5500U/C
5
23
24
2
S
H
A
R
P
21
3
1
4
Carrier
sheet
(Letter)
21
Drum
cartridge
18
19
AC cord
6
14
11
16
15
12
17
13
25
Toner
cartridge
Tape
20
NO.
PARTS CODE
1 TCADZ2136SCZZ
2 TLABP3937SCZZ
3 TLABZ3935SCZZ
TINSE3598SCZZ
4
TINSK3635SCZZ
5 SPAKP4946SCZZ
6 CPAKA4863SC01
11 CPLTP2803SC01
12 CPLTP2805SC01
13 TLABZ4016SCZZ
14 QCNW-4320SCZZ
15 SPAKA4861SCZZ
16 SPAKA4944SCZZ
17 DUNTK4925XHW2
QCNW-3975XHGY
18
QCNW-3247SCZZ
19 QCNW-3976XHOG
SPAKC4938SCZZ
20
SPAKC4984SCZZ
21 SPAKA4996SCZZ
23 SPAKA006ASCZZ
24 TLABH4074SCZZ
25 SPAKA010ASCZZ
PRICE
RANK
AB
AE
AE
AS
BU
AP
AZ
AU
AQ
AD
BB
AQ
AR
AY
AG
AH
AT
AW
AW
AC
AC
AD
AC
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
D
D
D
D
D
D
D
C
C
D
C
D
D
E
C
C
C
D
D
D
C
D
D
DESCRIPTION
Explanation card
Paper size label
Rapid key labels
Operation manual
Operation manual
Vinyl cover
Packing case, bottom ass’y
Document tray ass’y
Paper tray ass’y
IC component label
RS232C I/F cable
Packing add., top, right
Packing add., top, left
Handset
Telephone line cord
Telephone line cord
Handset cord
Packing case, top
Packing case, top
Printer sheet
Sheet
Label
Cassette pad
– 16 –
[U]
[C]
[U]
[U]
[C]
[U]
[C]
[C]
FO-5500U/C
16 Control PWB unit
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
PARTS CODE
UBAT-A005PRE0
VCEAEA1CW106M
VCEAEA1EW226M
VCEAEA1HW476M
VCEAEA1HW476M
VCEAEA1CW106M
VCEAEA1HW474M
VCEAEA1EW475M
VCEAEA1CW336M
VCEAEA1CW336M
VCEAEA1CW336M
VCEAEA1CW336M
VCEAEA1CW336M
VCEAEA1EW476M
VCEAEA1CW336M
VCEAEA1CW336M
VCKYTV1CF105Z
VCCSTV1HL102J
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCCSTV1HL102J
VCCSTV1HL391J
VCKYTV1CF105Z
VCKYTV1EB104K
VCKYTV1EB104K
VCKYTV1EF104Z
VCKYTV1CF105Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCCCTV1HH100D
VCKYTV1HB222K
VCKYTV1CF105Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCCCTV1HH100D
VCKYTV1CF105Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1EF104Z
VCCCTV1HH100D
VCCCTV1HH100D
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1HF104Z
VCKYTV1HB821K
VCCCTV1HH101J
VCCSTV1HL102J
VCCCTV1HH300J
VCCCTV1HH300J
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB821K
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB222K
PRICE
RANK
AN
AC
AA
AC
AC
AC
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
NEW
MARK
N
PART
RANK
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Battery
Capacitor(16WV 10µF)
Capacitor(50WV 0.47µF)
Capacitor(50WV 1000PF)
– 17 –
[BAT1]
[C2]
[C3]
[C5]
[C6]
[C7]
[C8]
[C9]
[C10]
[C11]
[C12]
[C13]
[C14]
[C15]
[C16]
[C17]
[C100]
[C101]
[C102]
[C103]
[C104]
[C105]
[C106]
[C107]
[C108]
[C109]
[C110]
[C111]
[C112]
[C113]
[C114]
[C116]
[C117]
[C118]
[C119]
[C120]
[C121]
[C122]
[C123]
[C124]
[C125]
[C126]
[C127]
[C130]
[C131]
[C132]
[C133]
[C134]
[C136]
[C137]
[C139]
[C140]
[C141]
[C142]
[C143]
[C144]
[C145]
[C146]
[C147]
[C148]
[C149]
[C151]
[C152]
[C153]
[C154]
[C155]
[C156]
[C157]
[C160]
[C161]
[C162]
[C163]
[C164]
[C165]
[C166]
[C167]
[C168]
[C169]
[C170]
[C171]
FO-5500U/C
16 Control PWB unit
NO.
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
PARTS CODE
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1HB222K
VCKYTV1CF105Z
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1HF104Z
VCKYTV1HB821K
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1HB821K
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB222K
VCCCTV1HH100D
VCCCTV1HH100D
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1EF104Z
VCCSTV1HL102J
VCCSTV1HL102J
VCKYTV1EB104K
VCKYTV1EF104Z
VCKYTV1EF104Z
VCCCTV1HH6R0C
VCCCTV1HH6R0C
VCKYTV1EF104Z
VCKYTV1HB222K
VCKYTV1EF104Z
VCKYTV1CF105Z
VCCCTV1HH6R0C
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1CF105Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCCSTV1HL102J
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1CF105Z
VCKYTV1HB222K
VCCSTV1HL102J
VCKYTV1HB472K
VCKYTV1HB103K
VCKYTV1CF105Z
VCKYTV1CF105Z
QCNCM7014SC0H
QCNCM2401SC0B
QCNCW2436SC2F
QCNCM2525SC5J
QCNCM2482SC2D
QCNCM2524SC3B
QCNCM7014SC1B
QCNCM2442SC0B
QCNCM2482SC1H
QCNCM7014SC0F
QCNCM7014SC0B
PRICE
RANK
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AB
AB
AB
AB
AA
AG
AK
AB
AP
AD
AB
AE
AB
AD
NEW
MARK
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Capacitor(50WV 6.0PF)
Connector(8pin)
Connector(2pin)
Connector(26pin)
Connector(50PIN)
Connector(24pin)
Connector(32PIN)
Connector(12pin)
Connector(2pin)
Connector(18pin)
Connector(6pin)
Connector(2pin)
– 18 –
[C172]
[C173]
[C174]
[C175]
[C177]
[C178]
[C179]
[C180]
[C181]
[C182]
[C183]
[C184]
[C185]
[C186]
[C187]
[C190]
[C191]
[C192]
[C193]
[C195]
[C196]
[C197]
[C198]
[C199]
[C200]
[C201]
[C202]
[C203]
[C204]
[C205]
[C215]
[C220]
[C222]
[C223]
[C224]
[C225]
[C226]
[C227]
[C228]
[C229]
[C230]
[C231]
[C232]
[C233]
[C234]
[C235]
[C236]
[C237]
[C241]
[C242]
[C243]
[C244]
[C246]
[C247]
[C248]
[C249]
[C250]
[C251]
[C252]
[C256]
[C257]
[C258]
[C259]
[C260]
[C262]
[C266]
[C267]
[C268]
[C269]
[CNCCD]
[CNLED]
[CNLIU]
[CNOP]
[CNPN]
[CNPRT]
[CNPW]
[CNROL]
[CNRS]
[CNSEN]
[CNSTP]
FO-5500U/C
16 Control PWB unit
NO.
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
197
198
199
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
PARTS CODE
QCNCM7014SC0D
VHD1SS355//-1
VHD1SS355//-1
VHDDAP202U/-1
VHDRB411D//-1
VHD1SS355//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHDRB411D//-1
VHVCCP2E30/-1
VHVCCP2E30/-1
VHVCCP2E20/-1
QSOCZ2051SC32
VHI27040FAN1G
VHI58512M10-1
VHIR144AFXL/1
QSOCZ2051SC32
VHI27040FAN0G
VHILH28F80S10
VHI4M16SOJ-70
VHI58512M10-1
VHI4M8SOJ-70/
VHI4M16SOJ-70
VHI4M8SOJ-70/
VHIH647702120
VHIPBL3717/-2
VHIHD813201F1
VHILZ9FJ37/-1
VHILR38292/-1
VHIPBL3717/-2
VHILH5116NA10
VHILH5268TH10
VHILH5268TH10
VHITLS1049/-1
VHINJM2904M-1
VHINJM4558MFVHIMC74HC14FVHIPST591CMT1
VHISN74LS244NR
VHINJU4051M-1
VHINJU6355E-1
VHISN74LS374NR
VHIBA10339F-1
VHIBU4053BCF1
VHIN78L05UA-1
VHIMC74HC04FVHIMC74HC32FVHIMC74HC74FVHIMC74HC08FVHIMC74HC08FVHIMC74HC157F
VHIMC74HC74FVRS-TQ2BB000J
VRS-TQ2BB000J
VRS-TQ2BB000J
VRS-TV2AB330J
VRS-TV2AB000J
VRS-TV2AB000J
PRICE
RANK
AB
AB
AB
AB
AD
AB
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AE
AE
AE
AC
BH
BA
BM
AC
BH
BH
BG
BA
BB
BG
BB
BS
AL
BE
AY
AY
AL
AL
AR
AR
AV
AE
AC
AD
AE
AG
AG
AM
AF
AD
AE
AK
AC
AC
AD
AC
AC
AD
AD
AA
AA
AA
AD
AA
AA
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
B
B
B
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
DESCRIPTION
Connector(4pin)
Diode(1SS355)
Diode(1SS355)
Diode(DAP202U)
Diode(RB411D)
Diode(1SS355)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
Diode(RB411D)
IC protector(CCP2E30)
IC socket(32pin)
IC ROM(27C040FAN1G)
IC(CXK58512-10LL)
IC(R144EFXL)
IC socket(32pin)
IC ROM(27C040FAN0G)
IC(LH28F800SUT)
IC(514260-70J)
IC(CXK58512-10LL)
IC(514800-70J)
IC(514260-70J)
IC(514800-70J)
IC(HD6477021)
IC(PBL3717/2)
IC(HD813201F)
IC(LZ9FJ37A)
IC(LR38292)
IC(PBL3717/2)
IC(LH5116NA-10)
IC(LH5268)
IC(LH5268)
IC(TLS1049)
IC(NJM2904M)
IC(NJM4558M)
IC(MC74HC14AF)
IC(PST591C)
IC(SN74LS244)
IC(NJU4051BM)
IC(NJU6355M)
IC(SN74LS374)
IC(BA10339F)
IC(BU4053BCF)
IC(NJU78L05UA)
IC(MC74HC04AF)
IC(MC74HC32AF)
IC(MC74HC74AF)
IC(MC74HC08AF)
IC(MC74HC08AF)
IC(MC74HC157AF)
IC(MC74HC74AF)
Resistor(1/8W 0Ω ±5%)
– 19 –
[CNTXM]
[D100]
[D102]
[D103]
[D104]
[D105]
[D110]
[D111]
[D112]
[D113]
[D114]
[D115]
[D116]
[D117]
[D118]
[D119]
[D120]
[D121]
[D122]
[D123]
[D124]
[D125]
[D126]
[D127]
[D128]
[D129]
[D130]
[D131]
[D148]
[D149]
[D150]
[F1]
[F2]
[F3]
[IC1]
[IC1]
[IC3]
[IC4]
[IC5]
[IC5]
[IC6]
[IC7]
[IC8]
[IC9]
[IC10]
[IC11]
[IC12]
[IC13]
[IC14]
[IC15]
[IC16]
[IC17]
[IC19]
[IC20]
[IC21]
[IC22]
[IC100]
[IC101]
[IC102]
[IC103]
[IC104]
[IC105]
[IC106]
[IC107]
[IC109]
[IC110]
[IC111]
[IC112]
[IC113]
[IC114]
[IC115]
[IC116]
[IC116]
[IC117]
[L100]
[L101]
[L102]
[L105]
[L106]
[L108]
FO-5500U/C
16 Control PWB unit
NO.
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
PARTS CODE
VRS-TV2AB000J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB000J
RCILZ2104SCZZ
RCILZ2104SCZZ
VS2SD1164//-1
VSDTA114EK/-1
VSDTA114EK/-1
VS2SC2413KP-1
VSDTC114EK/-1
VS2SD1664Q/-1
VRS-HT2HAR47J
VRS-HT2HAR47J
VRD-HT2HY910J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB103J
VRS-TV2AB103J
VRS-TV2AB103J
VRSTS2AD8662F
VRS-TV2AB103J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB151J
VRS-TV2AB151J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB333J
VRS-TV2AB333J
VRSTS2AD8662F
VRSTS2AD1742F
VRSTS2AD1183F
VRSTS2AD4752F
VRS-TV2AB000J
VRS-TV2AB302J
VRS-TV2AB102J
VRS-TV2AB151J
VRS-TV2AB151J
VRS-TV2AB151J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
RCORF2091SCZZ
VRS-TV2AB103J
VRS-TV2AB103J
VRS-TV2AB103J
VRS-TV2AB681J
VRS-TV2AB473J
VRS-TV2AB103J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB472J
VRS-TV2AB103J
VRS-TV2AB103J
VRS-TV2AB472J
PRICE
RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AK
AK
AE
AB
AB
AC
AB
AD
AB
AB
AA
AD
AD
AD
AD
AD
AD
AD
AD
AA
AA
AA
AA
AA
AD
AD
AD
AD
AA
AA
AA
AA
AA
AD
AD
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AD
AD
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AA
AA
AA
AA
NEW
MARK
N
N
N
N
N
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Coil(Z2104)
Coil(Z2104)
Transistor(2SD1164)
Transistor(DTA114EK)
Transistor(DTA114EK)
Transistor(2SC2413K)
Transistor(DTC114EK)
Transistor(2SD1664Q)
Resistor(1/2W 0.47Ω ±5%)
Resistor(1/2W 0.47Ω ±5%)
Resistor(1/10W 10KΩ ±5%)
Resistor(1/10W 86.6KΩ ±1%)
Coil
– 20 –
[L110]
[L111]
[L112]
[L113]
[L114]
[L115]
[L116]
[L117]
[L118]
[L119]
[L120]
[L121]
[L122]
[L124]
[L125]
[Q1]
[Q100]
[Q101]
[Q102]
[Q103]
[Q105]
[R1]
[R3]
[R6]
[R100]
[R101]
[R102]
[R103]
[R104]
[R105]
[R106]
[R107]
[R108]
[R109]
[R110]
[R111]
[R112]
[R113]
[R114]
[R115]
[R116]
[R117]
[R119]
[R121]
[R123]
[R124]
[R125]
[R126]
[R129]
[R130]
[R131]
[R132]
[R133]
[R134]
[R135]
[R136]
[R138]
[R139]
[R140]
[R141]
[R142]
[R143]
[R144]
[R145]
[R146]
[R147]
[R148]
[R149]
[R150]
[R151]
[R152]
[R153]
[R154]
[R155]
[R156]
[R157]
[R158]
[R159]
[R160]
[R161]
FO-5500U/C
16 Control PWB unit
NO.
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
PARTS CODE
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB101J
VRS-TV2AB000J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB000J
VRS-TV2AB103J
VRS-TV2AB000J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB000J
VRS-TV2AB472J
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB563J
VRS-TV2AB103J
VRS-TV2AB000J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB101J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB204J
VRS-TV2AB184J
VRS-TV2AB102J
VRS-TV2AB000J
VRS-TV2AB330J
VRS-TV2AB471J
VRS-TV2AB471J
VRS-TV2AB471J
VRS-TV2AB471J
VRS-TV2AB471J
VRS-TV2AB471J
VRS-TV2AB471J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB101J
VRS-TV2AB472J
VRS-TV2AB104J
VRS-TV2AB472J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB103J
VRS-TV2AB103J
VRS-TV2AB680J
VRS-TV2AB330J
VRS-TV2AB330J
VRS-TV2AB100J
VRS-TV2AB100J
VRS-TV2AB563J
VRS-TV2AB332J
VRS-TV2AB332J
VRS-TV2AB332J
VRS-TV2AB332J
PRICE
RANK
AA
AA
AA
AA
AA
AD
AD
AD
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AA
AA
AA
AA
AA
NEW
MARK
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
– 21 –
[R163]
[R165]
[R166]
[R167]
[R168]
[R171]
[R172]
[R173]
[R174]
[R175]
[R176]
[R177]
[R178]
[R179]
[R180]
[R181]
[R182]
[R183]
[R185]
[R186]
[R187]
[R188]
[R189]
[R190]
[R191]
[R192]
[R193]
[R194]
[R195]
[R196]
[R197]
[R198]
[R199]
[R200]
[R201]
[R202]
[R206]
[R207]
[R209]
[R210]
[R211]
[R213]
[R214]
[R215]
[R216]
[R217]
[R218]
[R219]
[R226]
[R227]
[R228]
[R229]
[R230]
[R231]
[R232]
[R233]
[R234]
[R235]
[R236]
[R237]
[R238]
[R241]
[R242]
[R243]
[R244]
[R245]
[R246]
[R247]
[R248]
[R249]
[R250]
[R252]
[R253]
[R254]
[R255]
[R256]
[R257]
[R258]
[R259]
[R260]
FO-5500U/C
16 Control PWB unit
NO.
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
PARTS CODE
VRS-TV2AB222J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB271J
VRS-TV2AB680J
VRS-TV2AB271J
VRS-TV2AB103J
VRS-TV2AB271J
VRS-TV2AB622J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB102J
VRS-TV2AB105J
VRS-TV2AB561J
VRS-TV2AB271J
VRS-TV2AB103J
VRS-TV2AB271J
VRS-TV2AB103J
VRS-TV2AB753J
VRS-TV2AB163J
VRS-TV2AB364J
VRS-TV2AB472J
VRS-TV2AB103J
VRS-TV2AB101J
VRS-TV2AB562J
VRS-TV2AB103J
VRS-TV2AB271J
VRS-TV2AB103J
VRS-TV2AB000J
VRS-TV2AB103J
VRS-TV2AB432J
VRS-TV2AB000J
VRS-TV2AB332J
VRS-TV2AB752J
VRS-TV2AB392J
VRS-TV2AB103J
VRS-TV2AB113J
VRS-TV2AB512J
VRS-TV2AB101J
VRS-TV2AB162J
VRS-TV2AB392J
VRS-TV2AB562J
VRS-TQ2BB561J
VRS-TV2AB000J
VRS-TQ2BB000J
RCORF2091SCZZ
VRS-TV2AB000J
VRS-TV2AB103J
VRS-TV2AB223J
VRS-TV2AB472J
VRS-TV2AB101J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB101J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TQ2BB200J
VRS-TV2AB000J
VRS-TV2AB102J
VRS-TV2AB472J
VRS-TV2AB472J
VRS-TV2AB102J
VRS-TV2AB472J
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB000J
VRS-TV2AB302J
VRS-TV2AB513J
PRICE
RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
AA
AA
AA
AD
AA
AA
AA
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
NEW
MARK
N
N
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Resistor(1/10W 1.0MΩ ±5%)
Coil
– 22 –
[R261]
[R262]
[R263]
[R264]
[R266]
[R267]
[R268]
[R269]
[R270]
[R271]
[R272]
[R273]
[R274]
[R275]
[R276]
[R277]
[R278]
[R279]
[R280]
[R281]
[R283]
[R284]
[R285]
[R289]
[R290]
[R292]
[R293]
[R294]
[R295]
[R296]
[R297]
[R298]
[R306]
[R307]
[R308]
[R310]
[R311]
[R313]
[R316]
[R318]
[R327]
[R328]
[R329]
[R331]
[R332]
[R333]
[R334]
[R335]
[R336]
[R337]
[R338]
[R339]
[R341]
[R347]
[R348]
[R351]
[R354]
[R355]
[R356]
[R357]
[R358]
[R359]
[R360]
[R361]
[R364]
[R365]
[R366]
[R367]
[R370]
[R371]
[R372]
[R373]
[R375]
[R377]
[R378]
[R379]
[R380]
[R381]
[R382]
[R383]
FO-5500U/C
16 Control PWB unit
NO.
PARTS CODE
VRS-TV2AB103J
RCRSQ2109SCZZ
RCRSQ1005LCZZ
RCRSZ7008SCZZ
RCRSQ2110SCZZ
RCRSP0074AFZZ
TLABP3078SCZZ
(Unit)
901 DCEKC582HSCZZ
482
483
484
485
486
487
488
PRICE
RANK
AA
AL
AE
AD
AG
AE
AA
NEW
MARK
CN
N
E
PRICE
RANK
AE
AB
AB
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AH
AE
AC
AG
AC
AB
AB
AB
AB
AG
AD
AD
AC
AC
AC
AC
AG
AC
AC
AC
AC
AC
AC
AD
AE
AH
NEW
MARK
N
PART
RANK
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
B
N
N
N
PART
RANK
C
B
B
B
B
B
D
DESCRIPTION
Crystal(38.00053MHz)
Crystal(19.6608MHz)
Crystal(16MHz)
Crystal(22.24044MHz)
Crystal(32.768kHz)
Shading label(for EP-ROM)
[R384]
[X1]
[X3]
[X4]
[X5]
[X6]
Control PWB unit(Within ROM)
17 TEL-Liu PWB unit
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
PARTS CODE
VHVRA391PV6-1
QTANZ2042SCZZ
VCEAGA1HW105M
VCEAGA1EW476M
VCEAGA1EW476M
VCEAGA1EW476M
VCEAGA1HW475M
VCEAGA1HW475M
VCEAGA1HW475M
VCEAGA1HW334M
VCEAGA1HW225M
VCEAGA1HW225M
VCEAGA1HW475M
VCEAGA1HW475M
VCEAGA1HW475M
RC-FZ2021SCZZ
VCKYPU1HB103K
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB331K
VCKYTV1EF104Z
VCKYTV1HB102K
VCKYTV1HB102K
VCKYTV1EF104Z
VCKYTV1EF104Z
VCKYTV1HB333K
VCKYTV1HB331K
VCKYTV1HB222K
VCKYTV1CF105Z
VCKYTV1HB221K
VCKYTV1HB102K
VCKYTV1EF104Z
VCKYTV1HB102K
VCKYTV1HB102K
VCKYTV1HB102K
VCKYTV1HB333K
RRLYZ0166AFZZ
QCNW-4561SCZZ
QCNCM2528SC0B
QCNCM2456SC2F
QCNCM688BAFZZ
VHD1SS355//-1
VHD1SS355//-1
VHD1SS355//-1
VHD1SS355//-1
VHINJM2113M-1
VHIBU4066BCF1
VHIBU4066BCF1
VHINJM4558MFVHINJM4558MFVHINJM4558MFRFILN2011SCZZ
RCILZ2089SCZZ
RFILN2011SCZZ
RCILZ2122SCZZ
RCILZ2122SCZZ
RFILN2011SCZZ
RFILN2011SCZZ
RFILN2011SCZZ
QJAKZ2060SC0B
QJAKZ2061SC0D
VHPTLP627//-1
N
N
N
N
DESCRIPTION
Varistor
Terminal
Relay
Cable(2pin)
Connector(2pin)
Connector(26pin)
Connector(2pin)
Diode(1SS355)
Diode(1SS355)
Diode(1SS355)
Diode(1SS355)
IC(NJM2113M)
IC(BU4066BCF)
IC(BU4066BCF)
IC(NJM4558M)
IC(NJM4558M)
IC(NJM4558M)
Coil(N2011)
Coil(Z2089)
Coil(N2011)
Coil(Z2122)
Coil(Z2122)
Coil(N2011)
Coil(N2011)
Coil(N2011)
Jack
Jack
Photo coupler(TLP627)
– 23 –
[AR1]
[ARG]
[C2]
[C3]
[C4]
[C5]
[C6]
[C7]
[C8]
[C9]
[C10]
[C11]
[C12]
[C13]
[C14]
[C15]
[C16]
[C101]
[C102]
[C103]
[C104]
[C105]
[C106]
[C107]
[C108]
[C109]
[C110]
[C111]
[C112]
[C114]
[C115]
[C116]
[C117]
[C118]
[C119]
[C120]
[C121]
[CML]
[CNHA]
[CNHB]
[CNLIU]
[CNSP]
[D101]
[D102]
[D103]
[D104]
[IC101]
[IC102]
[IC103]
[IC104]
[IC105]
[IC106]
[L1]
[L2]
[L3]
[L4]
[L5]
[L6]
[L7]
[L8]
[MJ1]
[MJTEL]
[PC1]
FO-5500U/C
17 TEL-Liu PWB unit
NO.
PARTS CODE
VHPTLP521-1BL
VSDTC114EK/-1
VSDTC114EK/-1
VSDTC114EK/-1
VSDTC114EK/-1
VSDTC114EK/-1
VS2SC2412KR-1
VSDTC114EK/-1
VSDTC114EK/-1
VS2SC2412KR-1
VSDTC114EK/-1
VSDTC114EK/-1
VRD-HT2HY101J
VRS-HT3AA470J
VRD-HT2EY223J
VRD-HT2HY223J
VRS-TS2AD223J
VRS-TS2AD103J
VRS-TS2AD103J
VRS-TS2AD113J
VRS-TS2AD273J
VRS-TS2AD753J
VRS-TS2AD104J
VRS-TS2AD332J
VRS-TS2AD000J
VRS-TS2AD103J
VRS-TS2AD822J
VRS-TS2AD223J
VRS-TS2AD223J
VRS-TS2AD223J
VRS-TS2AD393J
VRS-TS2AD243J
VRS-TS2AD153J
VRS-TS2AD183J
VRS-TS2AD223J
VRS-TS2AD681J
VRS-TS2AD223J
VRS-TS2AD104J
VRS-TS2AD223J
VRS-TS2AD223J
VRS-TS2AD223J
VRS-TS2AD223J
VRS-TS2AD751J
VRS-TS2AD223J
VRS-TS2AD621J
VRS-TS2AD621J
VRS-TS2AD221J
VRS-TS2AD513J
VRS-TS2AD153J
VRS-TS2AD102J
VRS-TS2AD151J
VRS-TS2AD222J
VRS-TS2AD332J
VRS-TS2AD473J
VRS-TS2AD331J
VRS-TS2AD102J
VRS-TS2AD683J
VRS-TS2AD102J
VRS-TS2AD822J
VRS-TS2AD103J
VRS-TS2AD273J
RH-DX2007SCZZ
QSW-Z2232SCZZ
RTRNZ2128XHZZ
VHVTN07G471-1
VHVTN07G471-1
VHEHZS2C1//-1
VHEHZS2C1//-1
VHEHZ27-1//-1
VHEHZS2C1//-1
VHEHZS2C1//-1
(Unit)
901 DCEKL494ASC01
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
PRICE
RANK
AE
AB
AB
AB
AB
AB
AD
AB
AB
AD
AB
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AE
AS
AB
AB
AB
AB
AB
AB
AB
NEW
MARK
N
N
PART
RANK
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
Photo coupler(TLP521)
Resistor(1W 47Ω ±5%)
Bridge diode(S1ZB60)
Hook switch
Transformer(600Ω)
Varistor(TNR7G471KT2)
Varistor(TNR7G471KT2)
Zener diode(HZS2C1)
Zener diode(HZS2C1)
Zener diode(HZ27C)
Zener diode(HZS2C1)
Zener diode(HZS2C1)
BD
N
E
TEL-Liu/hook switch PWB unit
N
N
N
N
DESCRIPTION
– 24 –
[PC2]
[Q101]
[Q102]
[Q103]
[Q104]
[Q105]
[Q106]
[Q107]
[Q108]
[Q109]
[Q110]
[Q111]
[R1]
[R2]
[R3]
[R4]
[R102]
[R103]
[R104]
[R105]
[R106]
[R107]
[R108]
[R109]
[R110]
[R111]
[R112]
[R113]
[R114]
[R115]
[R116]
[R117]
[R118]
[R119]
[R120]
[R121]
[R122]
[R123]
[R124]
[R125]
[R126]
[R127]
[R128]
[R129]
[R130]
[R131]
[R132]
[R133]
[R134]
[R135]
[R136]
[R137]
[R138]
[R139]
[R140]
[R141]
[R142]
[R143]
[R144]
[R145]
[R146]
[REC1]
[RHS]
[T1]
[VA1]
[VA2]
[ZD1]
[ZD2]
[ZD3]
[ZD4]
[ZD5]
FO-5500U/C
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
PARTS CODE
0AV1540000003
0AV1540000004
0AV1610000046
0AV1610000046
0AV1390000105
0AV1610000045
0AV1390000109
0AV1610000054
0AV1610000060
0AV1474720090
0AV1610000061
0AV1540000003
0AV1471020090
0AV1610000029
0AV1390000110
0AV1390000110
0AV1390000107
0AV1390000108
0AV1390000106
0AV1390000106
0AV1390000106
0AV1650000001
0AV1650000001
0AV1610000062
0AV1610000004
0AV5030090000
0AV5030091000
0AV5030036000
0AV5030088000
0AV5030089000
0AV3060033000
0AV3060021000
0AV3050019000
0AV3070093000
0AV3050030000
0AV3070094000
0AV3050066000
0AV3050030000
0AV3050075000
0AV5060031000
0AV5070000012
0AV5060067000
0AV5060067000
0AV5060067000
0AV3090056000
0AV3090041000
0AV3090060000
0AV3090016000
0AV4070044000
0AV4070044000
0AV4120002000
0AV4120002000
0AV4050014000
0AV4050013000
0AV4050014000
0AV3080621200
0AV3180000003
0AV3042543000
0AV3001015500
0AV2013343020
0AV2011033010
0AV2013903020
0AV2013933020
0AV2013933020
0AV2024783040
0AV2024783040
0AV2023903040
0AV2013333010
0AV2048203010
0AV2046803010
0AV2014733020
0AV2011033010
0AV2011533010
0AV2011023010
0AV2042203020
0AV2041513020
0AV2011023010
0AV2011023010
0AV2011043010
0AV2990015000
PRICE
RANK
AE
AF
AD
AD
AS
AC
AC
AD
AC
AB
AD
AE
AB
AC
AF
AF
AC
AC
AE
AE
AE
AF
AF
AE
AC
AD
AE
AC
AD
AG
AH
AB
AF
AC
AA
AC
AH
AA
AF
AG
AF
AF
AF
AF
AP
AF
AR
AG
AK
AK
AC
AC
AE
AE
AE
AF
AP
AQ
AC
AB
AA
AB
AB
AB
AC
AC
AC
AA
AC
AC
AB
AA
AA
AA
AC
AC
AA
AA
AA
AC
NEW
MARK
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
A
A
A
A
A
B
B
B
B
C
C
C
C
C
C
C
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Capacitor(470PF(KC))
Capacitor(1KWV 100PF)
Capacitor(1KWV 1000PF)
Connector
Connector
Connector
Connector
Connector
Diode(D3SB60Z)
Diode(ERA15-01)
Diode(ERA91-02)
Zener diode(RD20ES)
Diode(1SS178)
Zener diode(RD30ES)
Diode(YG901C2)
Diode(1SS178)
Diode(D2S4M-4004P15)
Fuse(125V 6.3A)
Thermal cutoff(127˚C)
Fuse(125V 4A)
Fuse(125V 4A)
Fuse(125V 4A)
IC(FA5315P)
IC(µPC1093J-1)
IC(PQ1CG1)
IC(NJM7812FA)
Coil
Coil
Coil
Coil
Coil
Coil
Coil
Photocoupler(TLP621GR)
Photo triac coupler(S21ME4FY)
FET(2SK2543)
Transistor(2SA1015-Y)
Resistor(1W 0.22Ω ±5%)
Resistor(1W 0.22Ω ±5%)
Resistor(1W 39Ω ±5%)
Fusing resistor(1/6W 82Ω ±5%)
Resistor(1/6W 22KΩ ±0.5%)
– 25 –
[C701]
[C702]
[C703]
[C704]
[C705]
[C706]
[C707]
[C708]
[C709]
[C710]
[C711]
[C712]
[C713]
[C714]
[C715]
[C716]
[C717]
[C718]
[C719]
[C720]
[C721]
[C722]
[C723]
[C724]
[C725]
[CN1]
[CN2]
[CN3]
[CN4]
[CNPW]
[D701]
[D702]
[D703]
[D704]
[D705]
[D706]
[D707]
[D708]
[D709]
[F701]
[F702]
[F703]
[F704]
[F705]
[IC701]
[IC702]
[IC703]
[IC704]
[L701]
[L702]
[L704]
[L706]
[L707]
[L708]
[L709]
[PC701]
[PC702]
[Q701]
[Q702]
[R701]
[R702]
[R703]
[R704]
[R705]
[R706]
[R707]
[R708]
[R709]
[R710]
[R711]
[R712]
[R713]
[R714]
[R715]
[R716]
[R717]
[R718]
[R719]
[R720]
[R721]
FO-5500U/C
NO.
PARTS CODE
0AV2990010000
0AV2990014000
0AV2990002000
0AV2021023040
0AV2013933020
0AV5040010000
0AV4000094411
0AV5140017000
0AV3160025000
0AV5190002000
0AV5190003000
0AV5190003000
0AV5050008000
0AV5180006000
0AV6114084711
0AV6114085811
0AV6114086811
0AV7510012000
0AV7700017000
0AV8117730514
0AV8130730414
(Unit)
901 RDENT2095SCZZ
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
PRICE
RANK
AC
AC
AB
AB
AB
AP
AX
AE
AN
AF
AF
AF
AC
AD
AH
AK
AE
AB
AD
AB
AB
NEW
MARK
BR
N
E
PRICE
RANK
AB
AB
AB
AB
AB
AC
AF
AE
AT
AA
AA
AA
AA
AA
AA
AA
AA
NEW
MARK
PART
RANK
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
BC
N
E
PRICE
RANK
AA
AA
AA
AD
AY
AA
AB
AA
AA
NEW
MARK
N
PART
RANK
C
C
C
C
B
C
B
C
C
AZ
N
E
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PART
RANK
C
C
C
C
C
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
DESCRIPTION
Resistor(1/6W 2.55KΩ ±0.5%)
Resistor(1W 1KΩ ±5%)
Switch
Transformer
Thermistor
Triac
Varistor
Varistor
Varistor
Holder
Terminal
Heat sink
Install bracket
Heat sink
Tube
Bush
Screw(B3×10)
Screw(B3×8)
[R722]
[R723]
[R724]
[R725]
[R726]
[S701]
[T701]
[TH701]
[TR701]
[X701]
[X702]
[X703]
Power supply PWB unit
19 RS232C I/F PWB unit
NO.
PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
901
VCEAEA1HW104M
VCEAEA1HW104M
VCEAEA1HW226M
VCEAEA1HW104M
VCEAEA1HW104M
VCTYPA1HF104Z
QCNCW2488SC0I
QCNCM2482SC1H
VHIADM207AN-1
RCORF5002BCZT
RCORF5002BCZT
RCORF5002BCZT
RCORF5002BCZT
RCORF5002BCZT
RCORF5002BCZT
RCORF5002BCZT
RCORF5002BCZT
(Unit)
DCEKI497ASC01
N
DESCRIPTION
Connector(9pin)
Connector(18pin)
IC(ADM207AN)
Core
Core
Core
Core
Core
Core
Core
Core
[C1]
[C2]
[C3]
[C4]
[C5]
[C6]
[CNDS]
[CNRS]
[IC1]
[L1]
[L2]
[L3]
[L4]
[L5]
[L6]
[L7]
[L8]
RS232C I/F PWB unit
20 CCD PWB unit
NO.
PARTS CODE
VCEAEA1EW226M
VCKYTQ1EF104Z
VCKYTQ1EF104Z
QCNCM704HAFZZ
VHIUPD3753CY1
VRS-TP2BD000J
VS2SA1037KS-1
VRS-TP2BD000J
VRS-TP2BD222J
(Unit)
901 DCEKD495ASC01
1
2
3
4
5
6
7
8
9
DESCRIPTION
Connector(8pin)
IC(UPD3753CY)
Transistor(2SA1037KS)
CCD PWB unit
– 26 –
[C1]
[C2]
[C3]
[CNCCD]
[IC1]
[J1]
[Q1]
[R1]
[R2]
FO-5500U/C
50 Hardware parts
NO.
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
W1
W2
PARTS CODE
LX-BZ2200SCZZ
LX-BZ2217SCZZ
XBPSD30P06K00
XBPSD40P08K00
XBPSE30P08K00
XEBSD30P06000
XEBSD30P08000
XEBSD30P10000
XEBSE30P08000
XEBSE30P10000
XHBSD30P06000
XHBSD30P08000
XHBSE30P06000
XHBSE30P10000
XHPSD30P08K00
XEPSD30P06X00
XUBSD20P06000
XRESJ50-06000
XWHSD30-08100
PRICE
RANK
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
NEW
MARK
N
N
N
PART
RANK
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
DESCRIPTION
Screw
Screw
Screw(M3×6K)
Screw(M4×8K)
Screw(3×8K)
Screw(M3×6)
Screw(M3×8)
Screw(M3×10)
Screw(M3×8)
Screw(M3×10)
Screw(3×6)
Screw(M3×8)
Screw(M3×6)
Screw(3×10)
Screw(M3×8K)
Screw(3×6)
Screw(2×6)
E type ring(5mm)
Washer(φ3)
– 27 –
FO-5500U/C
■ Index
PARTS CODE
[C]
CBSHP2079SC01
CCASP2083SC51
″
CCNW-4276XH01
CCNW-4557SC01
CPAKA4863SC01
CPLTP2803SC01
CPLTP2805SC01
CROLP2300SC01
CSW-M2222SC01
″
[D]
DCEKC582HSCZZ
″
DCEKD495ASC01
″
DCEKI497ASC01
″
DCEKL494ASC01
″
DCEKP496ASC01
DUNTK4925XHW2
[G]
GCABL2272SCZZ
GCABR2273SCZZ
GCASP2083SCZZ
GCOVA2363SCZZ
GCOVA2364SCYZ
GCOVA2367SCZZ
GCOVA2371SCZZ
GDAI-2074SCZZ
GDAI-2075SCZZ
GFTAF2110SCZZ
GMADZ2024SCZZ
[H]
HPNLC2370SCZZ
[J]
JBTN-2184SCZZ
JBTN-2185SCZZ
JBTN-2186SCZZ
JBTN-2187SCZZ
JBTN-2188SCZZ
JBTN-2189SCZZ
[L]
LANGH2803SCZZ
LBNDJ2006SCZZ
LBNDJ2007SCZZ
″
″
LBSHC2084SCZZ
LBSHP2066SCZZ
LBSHP2067SCZZ
LFRM-2167SCZZ
LHLDP2155SCZZ
LHLDW0004SCZZ
LHLDW1006FCZZ
LHLDW2156SCZZ
LHLDW2157SCZZ
LHLDW2158SCZZ
LPLTG2820SCZZ
LPLTM2806SCZZ
LPLTM2807SCZZ
LPLTM2808SCZZ
LPLTM2809SCZZ
LPLTM2810SCZZ
LPLTM2813SCZZ
LPLTM2814SCZZ
LPLTM2822SCZZ
LPLTM2834SCZZ
LPLTM2854SCZZ
LPLTM2856SCZZ
LPLTP2811SCZZ
LPLTP2812SCZA
LPLTP2819SCZZ
LPLTP2821SCZZ
LPLTP2823SCZZ
LPLTP2832SCZA
LPLTP2833SCZA
LX-BZ0175FCZZ
NO.
PRICE NEW PART
RANK MARK RANK
7- 1
2- 1
3- 901
1- 1
1- 2
15- 6
15- 11
15- 12
7- 2
1- 3
7- 3
AK
BQ
BQ
AU
AM
AZ
AU
AQ
AF
AE
AE
N
N
N
N
N
N
N
N
N
C
E
E
C
C
D
C
C
C
B
B
1- 4
16- 901
5- 1
20- 901
1- 5
19- 901
1- 6
17- 901
3- 1
15- 17
CN
CN
AZ
AZ
BC
BC
BD
BD
BC
AY
N
N
N
N
N
N
N
N
N
E
E
E
E
E
E
E
E
E
E
1- 8
1- 10
3- 2
1- 12
1- 13
1- 14
1- 15
1- 16
1- 17
1- 18
1- 19
AW
AW
AT
AQ
AT
AK
AL
AK
AE
AC
AF
N
N
N
N
N
N
N
N
N
N
N
D
D
D
C
C
C
C
C
C
C
C
3- 3
AK
N
C
3- 4
3- 5
3- 6
3- 7
3- 8
3- 9
AK
AH
AE
AE
AE
AE
N
N
N
N
N
N
C
C
C
C
C
C
5- 2
1- 61
1- 20
2- 5
4- 21
7- 4
7- 5
4- 1
7- 6
5- 3
1- 52
1- 21
1- 22
1- 23
1- 46
4- 2
1- 24
1- 25
1- 26
1- 27
1- 28
7- 7
7- 8
4- 3
6- 1
1- 50
1- 49
1- 30
1- 31
4- 4
4- 5
3- 10
5- 4
5- 5
14- 15
AF
AA
AA
AA
AA
AC
AC
AC
AW
AG
AB
AA
AC
AC
AC
AH
AY
AT
AU
AX
AG
AK
AK
AF
AQ
AK
AG
AY
AL
AD
AD
AF
AF
AF
AB
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PRICE NEW PART
RANK MARK RANK
PARTS CODE
NO.
LX-BZ2200SCZZ
LX-BZ2217SCZZ
[M]
MLEVP2229SCZZ
MLEVP2230SCZZ
MLEVP2242SCLZ
MLEVP2242SCRZ
MSPRC2843SCZZ
MSPRC2844SCZZ
MSPRC2845SCZZ
MSPRC2856SCZZ
MSPRC2867SCZZ
MSPRC2888SCZZ
MSPRC2889SCZZ
MSPRP2838SCZZ
MSPRP2839SCZZ
MSPRP2840SCZZ
MSPRP2841SCZZ
MSPRP2842SCZZ
MSPRP2846SCZZ
MSPRP2850SCZZ
[N]
NGERH2177SCZZ
NGERH2239SCZZ
NGERH2319SCZZ
NGERH2320SCZZ
NGERH2322SCZZ
NGERH2323SCZZ
NGERH2324SCZZ
NGERH2326SCZZ
NGERH2327SCZZ
NGERH2330SCZZ
NGERP2287SCZZ
NROLP2300XHZZ
NROLR2336SCZZ
NROLR2337SCZZ
NROLR2338SCZZ
NROLR2339SCZZ
NSFTZ2260SCZZ
NSFTZ2261SCZZ
NSFTZ2262SCZZ
NSFTZ2263SCZZ
[P]
PBRS-2047SCZZ
PCAPH2020SCZZ
PCUSS2097SCZZ
PCUSU2101SCZZ
PGIDP2454SCZZ
PGIDP2455SCZZ
PGIDP2456SCZZ
PGIDP2459SCZZ
PGLS-2057SCZZ
PGUMS2135SCZZ
PHOG-2073SCZZ
PHOP-2091SCZZ
PLNS-2050SCZZ
PMIR-2073SCZZ
PSHEZ3204SCZZ
PSHEZ3205SCZZ
PSHEZ3208SCZZ
PSHEZ3225SCZZ
PSHEZ3249SCZZ
PSHEZ3254SCZZ
PSHEZ3262SCZZ
PSHEZ3263SCZZ
PSHEZ3267SCZZ
PSHEZ3270SCZZ
PSPAZ0584FCZZ
PSTM-2015SCZZ
PTME-2051SCLZ
PTME-2051SCRZ
[Q]
QCNCM2401SC0B
QCNCM2442SC0B
QCNCM2456SC2F
QCNCM2482SC1H
″
QCNCM2482SC2D
QCNCM2524SC3B
QCNCM2525SC5J
50- B1
50- B2
AB
AB
N
C
C
1- 32
4- 6
14- 17
14- 16
4- 7
4- 8
4- 9
1- 33
4- 10
14- 19
14- 20
7- 9
7- 10
7- 11
7- 12
5- 6
4- 11
7- 13
AE
AG
AF
AF
AC
AA
AC
AC
AB
AC
AD
AC
AD
AD
AC
AC
AD
AD
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
7- 14
6- 2
7- 15
7- 16
7- 17
7- 18
6- 3
6- 4
4- 12
6- 5
1- 34
4- 13
4- 14
7- 19
7- 20
7- 21
7- 22
7- 23
7- 24
4- 15
AC
AC
AC
AD
AC
AD
AD
AD
AC
AE
AC
AC
AM
AH
AK
AM
AG
AH
AE
AD
4- 16
1- 62
3- 13
7- 35
1- 35
1- 36
4- 17
2- 2
2- 3
1- 37
1- 48
1- 38
5- 7
5- 8
5- 9
4- 18
7- 26
1- 40
4- 19
2- 4
2- 6
5- 12
1- 58
3- 14
14- 18
7- 28
1- 59
1- 60
AG
AT
AC
AC
AG
AF
AT
AS
AF
AC
AF
AU
AY
AL
AC
AD
AC
AF
AC
AC
AC
AC
AF
AC
AA
AX
AE
AE
16- 151
16- 157
17- 41
16- 158
19- 8
16- 154
16- 155
16- 153
AA
AB
AG
AE
AE
AB
AP
AK
– 28 –
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
N
N
C
C
C
C
C
C
C
C
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
PARTS CODE
QCNCM2528SC0B
QCNCM688BAFZZ
QCNCM7014SC0B
QCNCM7014SC0D
QCNCM7014SC0F
QCNCM7014SC0H
QCNCM7014SC1B
QCNCM704HAFZZ
QCNCW2436SC2F
QCNCW2488SC0I
QCNW-3247SCZZ
QCNW-3975XHGY
QCNW-3976XHOG
QCNW-4320SCZZ
QCNW-4554SCZZ
QCNW-4555SCZZ
QCNW-4558SCZZ
QCNW-4559SCZZ
QCNW-4560SCZZ
″
QCNW-4561SCZZ
QCNW-4562SCZZ
QCNW-4563SCZZ
QCNW-4564SCZZ
QCNW-4612SCZZ
QCNW-4668SCZZ
″
QJAKZ2060SC0B
QJAKZ2061SC0D
QSOCZ2051SC32
″
QSW-Z2232SCZZ
QSW-Z2236SCZZ
QSW-Z2237SCZZ
QTANZ2042SCZZ
[R]
RC-FZ2021SCZZ
RCILZ2089SCZZ
RCILZ2104SCZZ
″
RCILZ2122SCZZ
″
RCORF2063SCZZ
RCORF2064SCZZ
RCORF2091SCZZ
″
RCORF2094SCZZ
RCORF5002BCZT
″
″
″
″
″
″
″
RCORF7009XCZZ
RCRSP0074AFZZ
RCRSQ1005LCZZ
RCRSQ2109SCZZ
RCRSQ2110SCZZ
RCRSZ7008SCZZ
RDENT2095SCZZ
″
RFILN2011SCZZ
″
″
″
″
RH-DX2007SCZZ
RMOTZ2124SCZZ
RRLYZ0166AFZZ
RTRNZ2128XHZZ
[S]
SPAKA006ASCZZ
SPAKA010ASCZZ
SPAKA4861SCZZ
SPAKA4944SCZZ
SPAKA4996SCZZ
SPAKC4938SCZZ
SPAKC4984SCZZ
NO.
PRICE NEW PART
RANK MARK RANK
17- 40
17- 42
16- 160
16- 161
16- 159
16- 150
16- 156
20- 4
16- 152
19- 7
15- 18
15- 18
15- 19
15- 14
3- 11
5- 10
1- 41
1- 42
4- 20
6- 6
17- 39
7- 29
1- 43
1- 44
7- 30
1- 51
6- 7
17- 61
17- 62
16- 195
16- 199
17- 126
7- 31
7- 33
17- 2
AC
AC
AD
AB
AB
AB
AD
AD
AG
AF
AH
AG
AT
BB
AU
AL
AE
BA
AD
AD
AE
AK
AP
AS
AE
AC
AC
AD
AE
AC
AC
AE
AE
AE
AB
17- 16
17- 54
16- 254
16- 255
17- 56
17- 57
5- 13
1- 53
16- 307
16- 455
1- 54
19- 10
19- 11
19- 12
19- 13
19- 14
19- 15
19- 16
19- 17
1- 55
16- 487
16- 484
16- 483
16- 486
16- 485
1- 45
18- 901
17- 53
17- 55
17- 58
17- 59
17- 60
17- 125
6- 8
17- 38
17- 127
AC
AG
AK
AK
AC
AC
AE
AE
AD
AD
AE
AA
AA
AA
AA
AA
AA
AA
AA
AR
AE
AE
AL
AG
AD
BR
BR
AC
AC
AC
AC
AC
AC
BF
AH
AS
15- 23
15- 25
15- 15
15- 16
15- 21
15- 20
15- 20
AC
AC
AQ
AR
AC
AW
AW
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
C
C
C
C
C
C
C
B
B
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
E
E
C
C
C
C
C
B
B
B
B
C
D
D
D
D
D
D
FO-5500U/C
PARTS CODE
SPAKP4946SCZZ
[T]
TCADZ2136SCZZ
TINSE3598SCZZ
TINSK3635SCZZ
TLABH4065SCZZ
TLABH4066SCZZ
TLABH4074SCZZ
TLABP3078SCZZ
TLABP3937SCZZ
TLABZ3935SCZZ
TLABZ4016SCZZ
[U]
UBAT-A005PRE0
[V]
VCCCTV1HH100D
″
″
″
″
″
VCCCTV1HH101J
VCCCTV1HH300J
″
VCCCTV1HH6R0C
″
″
VCCSTV1HL102J
″
″
″
″
″
″
VCCSTV1HL391J
VCEAEA1CW106M
″
VCEAEA1CW336M
″
″
″
″
″
″
VCEAEA1EW226M
″
VCEAEA1EW475M
VCEAEA1EW476M
VCEAEA1HW104M
″
″
″
VCEAEA1HW226M
VCEAEA1HW474M
VCEAEA1HW476M
″
VCEAGA1EW476M
″
″
VCEAGA1HW105M
VCEAGA1HW225M
″
VCEAGA1HW334M
VCEAGA1HW475M
″
″
″
″
″
VCKYPU1HB103K
VCKYTQ1EF104Z
″
VCKYTV1CF105Z
″
″
″
″
″
″
″
NO.
PRICE NEW PART
RANK MARK RANK
15- 5
AP
15- 1
15- 4
15- 4
14- 21
1- 57
15- 24
16- 488
15- 2
15- 3
15- 13
AB
AS
BU
AD
AC
AD
AA
AE
AE
AD
16- 1
AN
16- 37
16- 44
16- 50
16- 51
16- 97
16- 98
16- 56
16- 58
16- 59
16- 109
16- 110
16- 115
16- 18
16- 24
16- 57
16- 104
16- 105
16- 125
16- 145
16- 25
16- 2
16- 6
16- 9
16- 10
16- 11
16- 12
16- 13
16- 15
16- 16
16- 3
20- 1
16- 8
16- 14
19- 1
19- 2
19- 4
19- 5
19- 3
16- 7
16- 4
16- 5
17- 4
17- 5
17- 6
17- 3
17- 11
17- 12
17- 10
17- 7
17- 8
17- 9
17- 13
17- 14
17- 15
17- 17
20- 2
20- 3
16- 17
16- 26
16- 30
16- 39
16- 45
16- 86
16- 114
16- 121
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AB
AB
AB
AB
AB
AB
AB
AA
AA
AA
AB
AB
AB
AB
AB
AB
AA
AC
AC
AA
AA
AA
AB
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
N
D
N
N
N
D
D
D
D
D
D
D
D
D
D
N
B
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
VCKYTV1CF105Z
″
″
″
VCKYTV1EB104K
″
″
VCKYTV1EF104Z
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VCKYTV1HB102K
NO.
16- 143
16- 148
16- 149
17- 30
16- 27
16- 28
16- 106
16- 19
16- 20
16- 21
16- 22
16- 23
16- 29
16- 31
16- 32
16- 33
16- 34
16- 35
16- 36
16- 40
16- 41
16- 42
16- 43
16- 46
16- 47
16- 49
16- 52
16- 60
16- 61
16- 63
16- 65
16- 66
16- 68
16- 77
16- 78
16- 79
16- 87
16- 92
16- 94
16- 95
16- 100
16- 101
16- 103
16- 107
16- 108
16- 111
16- 113
16- 116
16- 117
16- 118
16- 119
16- 120
16- 122
16- 123
16- 124
16- 126
16- 127
16- 128
16- 129
16- 130
16- 131
16- 132
16- 133
16- 134
16- 135
16- 136
16- 137
16- 138
16- 139
16- 140
16- 141
16- 142
17- 18
17- 19
17- 20
17- 22
17- 25
17- 26
17- 33
17- 23
– 29 –
PRICE NEW PART
RANK MARK RANK
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
VCKYTV1HB102K
″
″
″
″
VCKYTV1HB103K
VCKYTV1HB221K
VCKYTV1HB222K
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VCKYTV1HB331K
″
VCKYTV1HB333K
″
VCKYTV1HB472K
VCKYTV1HB821K
″
″
″
VCKYTV1HF104Z
″
VCTYPA1HF104Z
VHDDAP202U/-1
VHDRB411D//-1
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VHD1SS355//-1
″
″
″
″
″
″
NO.
17- 24
17- 32
17- 34
17- 35
17- 36
16- 147
17- 31
16- 38
16- 48
16- 53
16- 62
16- 64
16- 69
16- 70
16- 71
16- 72
16- 73
16- 74
16- 75
16- 76
16- 80
16- 81
16- 82
16- 83
16- 84
16- 85
16- 88
16- 91
16- 96
16- 99
16- 102
16- 112
16- 144
17- 29
17- 21
17- 28
17- 27
17- 37
16- 146
16- 55
16- 67
16- 90
16- 93
16- 54
16- 89
19- 6
16- 164
16- 165
16- 167
16- 168
16- 169
16- 170
16- 171
16- 172
16- 173
16- 174
16- 175
16- 176
16- 177
16- 178
16- 179
16- 180
16- 181
16- 182
16- 183
16- 184
16- 185
16- 186
16- 187
16- 188
16- 189
16- 190
16- 191
16- 162
16- 163
16- 166
17- 43
17- 44
17- 45
17- 46
PRICE NEW PART
RANK MARK RANK
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AB
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AB
AB
AB
AB
AB
AB
AB
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
FO-5500U/C
PARTS CODE
VHEHZS2C1//-1
″
″
″
VHEHZ27-1//-1
VHIADM207AN-1
VHIBA10339F-1
VHIBU4053BCF1
VHIBU4066BCF1
″
VHIHD813201F1
VHIH647702120
VHILH28F80S10
VHILH5116NA10
VHILH5268TH10
″
VHILR38292/-1
VHILZ9FJ37/-1
VHIMC74HC04FVHIMC74HC08F″
VHIMC74HC14FVHIMC74HC157F
VHIMC74HC32FVHIMC74HC74F″
VHINJM2113M-1
VHINJM2904M-1
VHINJM4558MF″
″
″
VHINJU4051M-1
VHINJU6355E-1
VHIN78L05UA-1
VHIPBL3717/-2
″
VHIPST591CMT1
VHIR144AFXL/1
VHISN74LS244NR
VHISN74LS374NR
VHITLS1049/-1
VHIUPD3753CY1
VHI27040FAN0G
VHI27040FAN1G
VHI4M16SOJ-70
″
VHI4M8SOJ-70/
″
VHI58512M10-1
″
VHPSNL14A70-1
VHPTLP521-1BL
VHPTLP627//-1
VHVCCP2E20/-1
VHVCCP2E30/-1
″
VHVRA391PV6-1
VHVTN07G471-1
″
VRD-HT2EY223J
VRD-HT2HY101J
VRD-HT2HY223J
VRD-HT2HY910J
VRS-HT2HAR47J
″
VRS-HT3AA470J
VRS-TP2BD000J
″
VRS-TP2BD222J
VRS-TQ2BB000J
″
″
″
VRS-TQ2BB200J
VRS-TQ2BB561J
VRS-TS2AD000J
VRS-TS2AD102J
″
″
NO.
17- 130
17- 131
17- 133
17- 134
17- 132
19- 9
16- 225
16- 226
17- 48
17- 49
16- 209
16- 207
16- 201
16- 213
16- 214
16- 215
16- 211
16- 210
16- 228
16- 231
16- 232
16- 219
16- 233
16- 229
16- 230
16- 234
17- 47
16- 217
16- 218
17- 50
17- 51
17- 52
16- 222
16- 223
16- 227
16- 208
16- 212
16- 220
16- 198
16- 221
16- 224
16- 216
20- 5
16- 199
16- 195
16- 202
16- 205
16- 204
16- 206
16- 197
16- 203
7- 34
17- 64
17- 63
16- 194
16- 192
16- 193
17- 1
17- 128
17- 129
17- 78
17- 76
17- 79
16- 264
16- 262
16- 263
17- 77
20- 6
20- 8
20- 9
16- 235
16- 236
16- 237
16- 454
16- 470
16- 452
17- 88
17- 113
17- 119
17- 121
PRICE NEW PART
RANK MARK RANK
AB
AB
AB
AB
AB
AT
AD
AE
AD
AD
BE
BS
BH
AL
AR
AR
AY
AY
AC
AC
AC
AD
AD
AC
AD
AD
AG
AE
AC
AC
AC
AC
AG
AM
AK
AL
AL
AE
BM
AG
AF
AV
AY
BH
BH
BG
BG
BB
BB
BA
BA
BC
AE
AH
AE
AE
AE
AE
AB
AB
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
VRS-TS2AD103J
″
″
″
VRS-TS2AD104J
″
VRS-TS2AD113J
VRS-TS2AD151J
VRS-TS2AD153J
″
VRS-TS2AD183J
VRS-TS2AD221J
VRS-TS2AD222J
VRS-TS2AD223J
″
″
″
″
″
″
″
″
″
″
VRS-TS2AD243J
VRS-TS2AD273J
″
VRS-TS2AD331J
VRS-TS2AD332J
″
VRS-TS2AD393J
VRS-TS2AD473J
VRS-TS2AD513J
VRS-TS2AD621J
″
VRS-TS2AD681J
VRS-TS2AD683J
VRS-TS2AD751J
VRS-TS2AD753J
VRS-TS2AD822J
″
VRS-TV2AB000J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TV2AB100J
″
″
″
″
″
″
″
″
″
NO.
17- 81
17- 82
17- 89
17- 123
17- 86
17- 101
17- 83
17- 114
17- 96
17- 112
17- 97
17- 110
17- 115
17- 80
17- 91
17- 92
17- 93
17- 98
17- 100
17- 102
17- 103
17- 104
17- 105
17- 107
17- 95
17- 84
17- 124
17- 118
17- 87
17- 116
17- 94
17- 117
17- 111
17- 108
17- 109
17- 99
17- 120
17- 106
17- 85
17- 90
17- 122
16- 239
16- 240
16- 241
16- 251
16- 252
16- 253
16- 282
16- 283
16- 284
16- 296
16- 322
16- 323
16- 324
16- 326
16- 332
16- 334
16- 337
16- 339
16- 340
16- 343
16- 368
16- 438
16- 441
16- 453
16- 456
16- 471
16- 477
16- 478
16- 479
16- 265
16- 266
16- 267
16- 268
16- 269
16- 270
16- 271
16- 272
16- 278
16- 279
– 30 –
PRICE NEW PART
RANK MARK RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
VRS-TV2AB100J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TV2AB101J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TV2AB102J
″
″
″
″
VRS-TV2AB103J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TV2AB104J
VRS-TV2AB105J
VRS-TV2AB113J
VRS-TV2AB151J
″
″
″
″
VRS-TV2AB162J
VRS-TV2AB163J
NO.
16- 280
16- 281
16- 288
16- 289
16- 302
16- 303
16- 304
16- 305
16- 306
16- 314
16- 315
16- 316
16- 317
16- 327
16- 328
16- 329
16- 330
16- 331
16- 354
16- 355
16- 356
16- 395
16- 396
16- 242
16- 243
16- 244
16- 245
16- 246
16- 247
16- 248
16- 249
16- 250
16- 325
16- 357
16- 377
16- 378
16- 379
16- 433
16- 448
16- 460
16- 466
16- 298
16- 367
16- 421
16- 472
16- 475
16- 273
16- 274
16- 275
16- 277
16- 308
16- 309
16- 310
16- 313
16- 319
16- 320
16- 333
16- 342
16- 390
16- 391
16- 409
16- 425
16- 427
16- 432
16- 435
16- 437
16- 439
16- 445
16- 457
16- 482
16- 381
16- 422
16- 446
16- 286
16- 287
16- 299
16- 300
16- 301
16- 449
16- 429
PRICE NEW PART
RANK MARK RANK
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
FO-5500U/C
PARTS CODE
VRS-TV2AB184J
VRS-TV2AB204J
VRS-TV2AB222J
VRS-TV2AB223J
VRS-TV2AB271J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TV2AB302J
″
VRS-TV2AB330J
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-TV2AB332J
″
″
″
″
VRS-TV2AB333J
″
VRS-TV2AB364J
VRS-TV2AB392J
″
VRS-TV2AB432J
VRS-TV2AB471J
″
″
″
″
″
″
VRS-TV2AB472J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
NO.
16- 366
16- 365
16- 402
16- 458
16- 383
16- 384
16- 385
16- 386
16- 387
16- 388
16- 389
16- 403
16- 404
16- 405
16- 406
16- 408
16- 410
16- 424
16- 426
16- 436
16- 297
16- 480
16- 238
16- 344
16- 345
16- 346
16- 347
16- 348
16- 349
16- 350
16- 351
16- 352
16- 353
16- 369
16- 393
16- 394
16- 398
16- 399
16- 400
16- 401
16- 442
16- 290
16- 291
16- 430
16- 444
16- 450
16- 440
16- 370
16- 371
16- 372
16- 373
16- 374
16- 375
16- 376
16- 318
16- 321
16- 335
16- 336
16- 338
16- 358
16- 359
16- 360
16- 361
16- 362
16- 363
16- 364
16- 380
16- 382
16- 412
16- 413
16- 414
16- 415
16- 416
16- 417
16- 418
16- 419
16- 420
16- 431
16- 459
16- 461
PRICE NEW PART
RANK MARK RANK
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
AA
AA
AA
AA
AA
AD
AD
AA
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
VRS-TV2AB472J
″
″
″
″
″
″
″
″
″
VRS-TV2AB473J
VRS-TV2AB512J
VRS-TV2AB513J
VRS-TV2AB561J
VRS-TV2AB562J
″
VRS-TV2AB563J
″
VRS-TV2AB622J
VRS-TV2AB680J
″
VRS-TV2AB681J
VRS-TV2AB752J
VRS-TV2AB753J
VRSTS2AD1183F
VRSTS2AD1742F
VRSTS2AD4752F
VRSTS2AD8662F
″
VSDTA114EK/-1
″
VSDTC114EK/-1
″
″
″
″
″
″
″
″
″
VS2SA1037KS-1
VS2SC2412KR-1
″
VS2SC2413KP-1
VS2SD1164//-1
VS2SD1664Q/-1
VVLLMG2025TPR
[X]
XBPSD30P06K00
XBPSD40P08K00
XBPSE30P08K00
XEBSD30P06000
XEBSD30P08000
XEBSD30P10000
XEBSE30P08000
XEBSE30P10000
XEPSD30P06X00
XHBSD30P06000
XHBSD30P08000
XHBSE30P06000
XHBSE30P10000
XHPSD30P08K00
XRESJ50-06000
XUBSD20P06000
XWHSD30-08100
[0]
0AV1390000105
0AV1390000106
″
″
0AV1390000107
0AV1390000108
0AV1390000109
0AV1390000110
″
0AV1471020090
0AV1474720090
0AV1540000003
″
NO.
PRICE NEW PART
RANK MARK RANK
16- 462
16- 463
16- 464
16- 465
16- 467
16- 468
16- 469
16- 473
16- 474
16- 476
16- 312
16- 447
16- 481
16- 423
16- 434
16- 451
16- 341
16- 397
16- 411
16- 392
16- 407
16- 311
16- 443
16- 428
16- 294
16- 293
16- 295
16- 276
16- 292
16- 257
16- 258
16- 260
17- 65
17- 66
17- 67
17- 68
17- 69
17- 71
17- 72
17- 74
17- 75
20- 7
17- 70
17- 73
16- 259
16- 256
16- 261
3- 12
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AD
AD
AC
AE
AD
BA
50- B3
50- B4
50- B5
50- B6
50- B7
50- B8
50- B9
50- B10
50- B16
50- B11
50- B12
50- B13
50- B14
50- B15
50- W1
50- B17
50- W2
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
18- 5
18- 19
18- 20
18- 21
18- 17
18- 18
18- 7
18- 15
18- 16
18- 13
18- 10
18- 1
18- 12
AS
AE
AE
AE
AC
AC
AC
AF
AF
AB
AB
AE
AE
– 31 –
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
0AV1540000004
0AV1610000004
0AV1610000029
0AV1610000045
0AV1610000046
″
0AV1610000054
0AV1610000060
0AV1610000061
0AV1610000062
0AV1650000001
″
0AV2011023010
″
″
0AV2011033010
″
0AV2011043010
0AV2011533010
0AV2013333010
0AV2013343020
0AV2013903020
0AV2013933020
″
″
0AV2014733020
0AV2021023040
0AV2023903040
0AV2024783040
″
0AV2041513020
0AV2042203020
0AV2046803010
0AV2048203010
0AV2990002000
0AV2990010000
0AV2990014000
0AV2990015000
0AV3001015500
0AV3042543000
0AV3050019000
0AV3050030000
″
0AV3050066000
0AV3050075000
0AV3060021000
0AV3060033000
0AV3070093000
0AV3070094000
0AV3080621200
0AV3090016000
0AV3090041000
0AV3090056000
0AV3090060000
0AV3160025000
0AV3180000003
0AV4000094411
0AV4050013000
0AV4050014000
″
0AV4070044000
″
0AV4120002000
″
0AV5030036000
0AV5030088000
0AV5030089000
0AV5030090000
0AV5030091000
0AV5040010000
0AV5050008000
0AV5060031000
0AV5060067000
″
″
0AV5070000012
0AV5140017000
0AV5180006000
0AV5190002000
0AV5190003000
NO.
18- 2
18- 25
18- 14
18- 6
18- 3
18- 4
18- 8
18- 9
18- 11
18- 24
18- 22
18- 23
18- 74
18- 77
18- 78
18- 61
18- 72
18- 79
18- 73
18- 68
18- 60
18- 62
18- 63
18- 64
18- 85
18- 71
18- 84
18- 67
18- 65
18- 66
18- 76
18- 75
18- 70
18- 69
18- 83
18- 81
18- 82
18- 80
18- 59
18- 58
18- 33
18- 35
18- 38
18- 37
18- 39
18- 32
18- 31
18- 34
18- 36
18- 56
18- 48
18- 46
18- 45
18- 47
18- 89
18- 57
18- 87
18- 54
18- 53
18- 55
18- 49
18- 50
18- 51
18- 52
18- 28
18- 29
18- 30
18- 26
18- 27
18- 86
18- 93
18- 40
18- 42
18- 43
18- 44
18- 41
18- 88
18- 94
18- 90
18- 91
PRICE NEW PART
RANK MARK RANK
AF
AC
AC
AC
AD
AD
AD
AC
AD
AE
AF
AF
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AC
AC
AC
AC
AC
AC
AC
AB
AC
AC
AC
AC
AQ
AF
AA
AA
AH
AF
AB
AH
AC
AC
AF
AG
AF
AP
AR
AN
AP
AX
AE
AE
AE
AK
AK
AC
AC
AC
AD
AG
AD
AE
AP
AC
AG
AF
AF
AF
AF
AE
AD
AF
AF
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
B
C
A
A
A
A
A
B
C
B
B
FO-5500U/C
PARTS CODE
0AV5190003000
0AV6114084711
0AV6114085811
0AV6114086811
0AV7510012000
0AV7700017000
0AV8117730514
0AV8130730414
0KW0910362001
0KW0928300602
0KW0928301902
0KW0933382612
0KW0933384002
0KW0933390202
0KW0933390302
0KW0933392201
0KW0933392301
0KW0956202701
0KW0957010101
0KW0957251103
0KW0957320801
0KW0957321501
0KW0957551101
0KW0957552702
0KW0972553101
0KW0992010224
0KW0992011903
0KW0992012102
0KW0992039101
0KW0992044301
0KW0992048303
0KW0992053306
0KW0992075101
0KW0992075201
0KW0992075901
0KW0992100601
0KW0992101703
0KW0992180102
0KW0992180203
0KW0992180302
0KW0992180401
0KW0992180501
0KW0992180601
0KW0992180701
0KW0992200117
0KW0992200412
0KW0992200512
0KW0992200603
0KW0992200701
0KW0992201201
0KW0992201304
0KW0992201902
0KW0992202014
0KW0992202101
0KW0992202202
0KW0992202301
0KW0992202401
0KW0992203301
0KW0992203401
0KW0992203801
0KW0992230413
0KW0992230514
0KW0992230712
0KW0992230825
0KW0992231002
0KW0992231101
″
0KW0992231314
0KW0992232012
0KW0992241202
0KW0992241302
0KW0992241402
0KW0992242301
0KW0992250102
0KW0992250213
0KW0992250301
0KW0992250401
0KW0992250512
0KW0992250601
0KW0992250701
NO.
18- 92
18- 95
18- 96
18- 97
18- 98
18- 99
18- 100
18- 101
10- 46
13- 12
13- 15
13- 3
13- 2
14- 6
14- 10
14- 5
14- 11
9- 62
10- 50
13- 20
11- 7
11- 4
12- 23
12- 34
12- 15
11- 2
9- 2
9- 67
11- 13
10- 7
12- 13
10- 1
9- 47
10- 29
11- 9
8- 17
12- 2
8- 11
12- 3
8- 3
8- 19
8- 21
12- 44
8- 23
9- 4
9- 29
9- 3
10- 3
10- 2
10- 4
10- 31
10- 9
10- 11
10- 12
10- 32
9- 5
10- 24
9- 57
9- 30
9- 63
8- 6
9- 13
9- 1
9- 18
8- 5
9- 61
10- 33
9- 23
9- 7
10- 14
10- 13
9- 9
9- 64
9- 32
9- 27
9- 25
9- 26
9- 28
9- 35
9- 33
PRICE NEW PART
RANK MARK RANK
AF
AH
AK
AE
AB
AD
AB
AB
AC
AG
AL
AH
AF
AT
AT
AN
AN
AF
AZ
AG
AF
AE
AK
AF
AE
AV
CA
AX
BQ
AS
CD
CA
BB
AZ
BA
AF
AC
BH
AY
AQ
AL
AF
AE
AE
BG
AL
AQ
AF
AD
AD
AD
AF
AD
AC
AF
AD
AD
AC
AQ
AD
AG
AF
AP
AH
AG
AC
AC
AF
AD
AF
AF
AD
AF
AL
AH
AG
AG
AH
AF
AG
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
C
C
C
C
C
C
E
E
B
E
C
E
E
C
C
C
C
C
C
C
C
C
C
C
C
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
C
C
C
C
C
C
C
PARTS CODE
0KW0992250813
0KW0992250901
0KW0992251001
0KW0992251112
0KW0992251212
0KW0992251301
0KW0992251401
0KW0992255001
0KW0992255101
0KW0992255202
0KW0992280102
0KW0992280201
0KW0992280301
0KW0992280401
0KW0992281201
0KW0992300124
0KW0992300202
0KW0992300301
0KW0992300601
″
0KW0992300701
0KW0992300802
0KW0992300901
0KW0992301012
0KW0992301102
0KW0992301401
0KW0992301502
0KW0992301603
0KW0992301804
0KW0992301901
0KW0992302112
0KW0992302202
0KW0992302401
0KW0992302501
0KW0992302902
0KW0992303505
0KW0992304001
″
0KW0992304101
0KW0992304513
0KW0992305036
0KW0992305201
0KW0992305301
0KW0992305501
0KW0992310401
0KW0992320102
0KW0992320701
0KW0992320801
0KW0992350102
0KW0992350205
0KW0992350301
0KW0992370601
0KW0992370701
0KW0992370901
0KW0992371101
0KW0992380101
0KW0992380202
0KW0992380301
0KW0992381501
0KW0992382001
0KW0992401503
0KW0992410112
0KW0992420101
0KW0992420301
0KW0992420412
0KW0992420512
0KW0992420601
0KW0992420712
0KW0992420812
0KW0992421001
0KW0992421301
0KW0992421402
0KW0992551201
0KW0992551713
0KW0992551801
0KW0992551901
0KW0992552101
0KW0992552401
0KW0992553103
0KW0992553201
NO.
12- 7
12- 8
12- 12
12- 11
12- 10
12- 9
9- 34
12- 6
12- 5
12- 4
9- 8
9- 10
9- 66
9- 78
9- 65
9- 24
9- 52
10- 27
9- 43
10- 17
10- 21
9- 19
9- 20
9- 15
9- 38
9- 37
9- 17
10- 22
9- 42
9- 16
9- 54
9- 48
10- 23
10- 30
9- 22
9- 44
9- 21
13- 26
9- 46
10- 16
10- 15
9- 60
10- 41
10- 42
10- 28
10- 20
10- 18
10- 44
9- 49
9- 41
9- 40
12- 35
11- 6
11- 5
11- 3
11- 21
11- 22
10- 53
11- 1
11- 8
12- 14
9- 51
11- 16
11- 15
11- 19
11- 14
11- 12
11- 10
11- 20
11- 11
11- 17
11- 18
12- 16
12- 19
12- 36
12- 37
12- 17
12- 21
12- 18
12- 30
– 32 –
PRICE NEW PART
RANK MARK RANK
AG
AF
AN
AD
AF
AC
AF
AF
AC
AF
AX
AQ
AF
AE
AH
AQ
AR
AF
AD
AD
AD
AF
AD
AG
AD
AD
AD
AD
AD
AF
AF
AF
AN
AD
AM
AF
AC
AC
AC
AD
AD
AC
AC
AG
AL
AG
AF
AC
AR
AN
AD
AF
AD
AD
AD
AF
AH
AF
AL
AV
AH
AP
BL
AS
AH
AG
AG
AD
AC
AH
AG
AC
AL
AC
AD
AC
AH
AD
AF
AD
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
0KW0992553303
0KW0992554001
0KW0992554101
0KW0992554501
0KW0992562501
0KW0992562601
0KW0992563401
0KW0992580602
0KW0992605202
0KW0992605301
0KW0992605413
0KW0992605501
0KW0992605601
0KW0992606101
0KW0992606604
0KW0992606801
0KW0992610401
0KW0992621213
0KW0992650501
0KW0992671301
0KW0992671501
0KW0992731201
0KW0997231203
0KW0997605101
0KW0997605201
0KW0997610201
0KW0997621204
0KW0997630101
0KW1200123602
0KW1200312003
0KW4150010103
0KW4150020201
0KW4150102902
0KW4150104301
0KW4150180103
0KW4150180201
0KW4150180303
0KW4150180702
0KW4150180801
0KW4150180901
0KW4150181001
0KW4150181301
0KW4150181502
0KW4150181703
0KW4150181801
0KW4150181901
0KW4150182001
0KW4150182201
0KW4150182402
0KW4150182503
0KW4150182701
0KW4150182801
0KW4150183101
0KW4150183201
0KW4150183301
0KW4150183602
0KW4150184501
0KW4150184601
0KW4150184701
0KW4150620101
0KW4150731301
0KW9335141031
″
0KW9383251011
0KW9384131091
0KW9384131111
0KW9646030613
0KW9646030813
0KW9646040813
0KW9721040001
″
0KW9733031013
0KW9733031413
0KW9735030613
″
0KW9735030813
″
0KW9735031213
0KW9739030613
0KW9739030813
NO.
12- 33
12- 24
12- 25
12- 45
12- 29
12- 27
12- 22
12- 32
9- 55
12- 39
10- 8
10- 19
10- 5
10- 38
12- 20
9- 68
9- 31
9- 39
12- 31
12- 28
12- 26
12- 40
10- 49
10- 51
10- 47
8- 4
10- 6
10- 48
9- 53
13- 13
13- 32
13- 23
13- 19
13- 27
13- 5
13- 4
13- 34
14- 1
14- 2
13- 9
13- 33
13- 1
14- 8
13- 30
14- 3
13- 28
13- 11
13- 31
14- 4
14- 7
14- 12
14- 22
13- 16
13- 14
13- 17
13- 29
13- 6
13- 7
13- 41
13- 18
14- 13
9- 36
12- 38
9- 58
13- 42
10- 37
12- 42
9- 73
13- 39
9- 77
13- 40
12- 43
9- 76
9- 71
10- 56
9- 75
10- 55
10- 58
11- 24
8- 22
PRICE NEW PART
RANK MARK RANK
AH
BF
BR
AU
AQ
AN
AD
BT
AL
AG
AQ
AU
AN
AN
AQ
AQ
BF
AV
BE
BB
AZ
AF
AH
AL
AM
BC
BV
AN
AC
AD
BS
AX
AH
AR
AU
AX
AY
BA
AD
AP
AP
AG
AN
AN
AQ
AP
AV
AL
AL
BK
AH
AE
AG
AF
AF
AH
AD
AD
AF
BT
AF
BA
BA
AD
AC
AC
AB
AB
AC
AB
AB
AB
AB
AB
AB
AC
AC
AB
AB
AB
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
D
C
C
C
B
E
B
C
C
E
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
D
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
FO-5500U/C
PARTS CODE
0KW9739030813
″
″
″
″
0KW9742030813
″
″
″
0KW9742031013
0KW9743030813
0KW9770030813
NO.
9- 72
10- 54
11- 23
12- 41
14- 14
9- 70
10- 57
11- 25
13- 35
13- 36
13- 37
9- 74
PRICE NEW PART
RANK MARK RANK
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AC
N
N
N
N
N
N
N
PARTS CODE
NO.
C
C
C
C
C
C
C
C
C
C
C
C
– 33 –
PRICE NEW PART
RANK MARK RANK
PARTS CODE
NO.
PRICE NEW PART
RANK MARK RANK
FO-5500U/C
CAUTION FOR BATTERY REPLACEMENT
(Danish)
ADVARSEL !
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the equipment manufacturer.
Discard used batteries according to manufacturer’s instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type recommandé par le constructeur.
Mettre au rébut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfare vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
FO-5500U/C
COPYRIGHT © 1996 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Communication & Audio Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-01, Japan
Printed in USA
9610-2280NS•IS•J

service manual facsimile model fo-5500

Transcription

Similar documents

SERVICE MANUAL FACSIMILE MODEL FO-5700

SHARP 37GQ20H02

FACSIMILE UX-510A MODEL FO

Service Manual

VESTAX MODEL: PDX-2000