GF 5010.3 Fabric @ Sofa Accent Pillow
Transcription
GF 5010.3 Fabric @ Sofa Accent Pillow
GF 5010.3 Fabric @ Sofa Accent Pillow Areas Local Representative: 1.Reference Number: 2.Quantity: 3.Fabric Name/ Number: 4.Color: 5.Width: 6.Content: 7.Finish: 8. Abrassion: 9.Backing Code: Living Room x 2 yard Donghia 101 Henry Adams Street, Suite# 144 San Francisco, CA 94103 T:415-8617717 F:415-552-3113 E:[email protected] Refer to GF-5010.2 of Fabric Location Fabricator to verify quantity requirements. Approximately 2.5 yards. Mayreau 8006/918 Platine 54" 63% Polyester, 35% Viscose, 2% Polyacrylic Fabric must be treated with Crypton finish for soil and stain repellency. 10,000 Double Rubs Fabric Backing as required and as recommended by fabric supplier. GF 5010.3 Fabric @ Sofa Accent Pillow (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 1 of 9 10.Fabrication Requirements: 11.Submittal Requirements: Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF 5010.3 Fabric @ Sofa Accent Pillow (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 1 of 9 GF- 5014.1 Fabric@ Desk Chair Areas Manufacturer: Local Representative: 1.Reference: 2.Quantity: 3.Fabric Name/ Number: 4.Color: 5.Repeat: 6.Content: 7.Finish: 8.Width: 9.Backing Code: 10.Abbrasion: Bedroom x 2 yard Joesph Noble Incorporated 2025 Irving Blvd. Dallas, Texas, 75207 T: 214.741.8100 F:415.626.6883 De Sousa Hughes 2 Henry Adams Street #220 San Francisco, CA 94103 T. 415626.6883 F. 415-626.2483 Refer to GF-5011 Lounge Chair for fabric location. Fabricator must verify all quantity requirements. Approximately 3 yards per chair. Amazing 9000-13 Sublime None 84% Polyester, 16% Cotton Fabric must be treated with Crypton finish for soil and stain repellency. 54" Fabric Backing as required and as recommended by fabric supplier. 100,000 Double Rubs GF- 5014.1 Fabric@ Desk Chair (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 2 of 9 11.Fabrication Requirements: 12.Submittal Requirements: Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF- 5014.1 Fabric@ Desk Chair (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 2 of 9 GF-5006.1 Fabric @ Headboard Areas Measurements Manufacturer: Local Representative: 1. Reference 2. Quantity 3. Fabric Name/Number 4. Color 5. Repeat 6. Content 7. Finish Bedroom x 2 each CUSTOM: () Romo Inc 16722 West Park Circle Drive Chagrin Falls, Ohio 44023 T. 1 800 338 2783 F. 1 800 775 0609 www.villaromo.com De Sousa Hughes 2 Henry Adams St., Suite 220 San Francisco CA 94103 T. 415626.6883 F. 415-626.2483 Website:www.desousahughes.com [email protected] Refer to GF-5006 Bed for fabric location. Fabricator must verify all quantity requirements. Seville Washable VN 1043 148 None 100% Cotton Fabric must be treated with Crypton finish for soil and stain repellency. GF-5006.1 Fabric @ Headboard (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 3 of 9 8. Width 9. Backing Code 10. Abbrasion 11. Fabrication Requirements 12. Submittal Requirements 55" Fabric Backing as required and as recommended by fabric supplier. 25,000 GD/W Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF-5006.1 Fabric @ Headboard (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 3 of 9 GF-5010.1 Fabric @ Sofa Areas Manufacturer: Local Representative: 1.Reference: 2.Quantity: 3.Fabric Name/ Number: 4.Color: 5.Repeat: 6.Content: 7.Finish: 8. Width: 9.Backing Code: 10.Abbrasion: Living Room x 1 yard Glant Textiles Corporation P.O. Box 84228 Seattle, WA 9812 T: 206 725 4444 Kneedler Fauchere 101 Henry Adams Street #170 San Francisco, CA 94103 T. 415487-6180 F. 415-487-6192 E. [email protected] Refer to GF-5010 Sofa for fabric location. Fabricator to verify quantity requirements. Approximately 14 yards, Riviera 9582 Bone 01 None 44% Cotton, 31% Polyester, 25% Rayon Fabric must be treated with Crypton finish for soil and stain repellency. 54" Fabric Backing as required and as recommended by fabric supplier. 100,0000 Double Rubs GF-5010.1 Fabric @ Sofa (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 4 of 9 11.Fabrication Requirements: 12.Submittal Requirements: Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF-5010.1 Fabric @ Sofa (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 4 of 9 GF-5010.4 Welt Fabric @ Sofa Accent Pillow Manufacturer: Local Representative: 1.Reference: 2.Quantity: 3.Fabric Name/ Number: 4.Color: 5.Repeat: 6.Content: 7.Finish: 8.Width: 9.Backing Code: 10.Abbrasion: Brentano, Inc. 260 Holbrook Drive Wheeling, IL 60090 T : 847.657.848 F : 847.657.8641 Donghia, San Francisco 101 Henry Adams St., Ste 144 San Francisco, CA 9410 T : 415.861.7717 F : 415.552.3113 Refere to GF5010.3 for fabric location Fabricator to verify quantity requiremets. Approximately 6mm thick piping bordering all sides of the pillow. Simplicity 1010-01 Carrara None 46% Cotton, 40% Viscose, 10% Polyester, 4% Linen Fabric must be treated with Crypton finish for soil and stain repellency. 54" Fabric Backing as required and as recommended by fabric supplier. 45,000 Double Rubs GF-5010.4 Welt Fabric @ Sofa Accent Pillow (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 5 of 9 11.Fabrication Requirements: 12.Submittal Requirements: Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF-5010.4 Welt Fabric @ Sofa Accent Pillow (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 5 of 9 GF-5011.1 Fabric @ Lounge Chair Manufacturer: Local Representative: 1.Reference: 2.Quantity: 3. Fabric Name/ Number: 4.Color: 5.Repeat: 6.Content: 7.Finish: 8.Width: 9.Backing Code: 10.Abbrasion: Castel 419 E 57th Street New York NY 10022 T: 212 758 9900 F: 646 224 8695 [email protected] Donghia, 101 Henry Adams Street, Suite# 144 San Francisco, CA 94103 T:415-8617717 Refer to GF-5011.1 of Fabric Location Fabricator to verify quantity requirements. Mayreau 8006/918 Platine None 63% Polyester, 35% Viscose, 2% Polyacrylic Fabric must be treated with Crypton finish for soil and stain repellency. 54" Fabric Backing as required and as recommended by fabric supplier. 51,000 Wyzenbeek GF-5011.1 Fabric @ Lounge Chair (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 6 of 9 11. Fabricaiton Requirements: 12. Submittal Requirements: Notes Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. 1. GF-5011.1 Fabric @ Lounge Chair (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 6 of 9 GF-5011.3 Fabric@ Lounge Chair Accent Pillow Manufacturer: Local Representative: 1.Reference: 2.Quantity: 3.Fabric Name/ Number: 4.Repeat: 5.Content: 6.Finish: 7.Width: 8.Backing Code: 9.Fabrication Requirements: Bergamo 256 Washington Street Mt. Vernon, NY 10553 T:914.665.0800 F:914.665.7900 Donghia, 101 Henry Adams Street, Suite# 144 San Francisco, CA 94103 T:415-8617717 Refer to GF-5011.2 of Fabric Location : Fabricator to verify quantity requirements. Approximately 3 yards. Trias 2339-3 3.5" 100% Cotton Viscose Fabric must be treated with Crypton finish for soil and stain repellency. 55" Fabric Backing as required and as recommended by fabric supplier. Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. GF-5011.3 Fabric@ Lounge Chair Accent Pillow (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 7 of 9 10.Submittal Requirements: - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF-5011.3 Fabric@ Lounge Chair Accent Pillow (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 7 of 9 GF-5012.1 Fabric @ Ottoman Areas Manufacturer: Local Representative: 1.Reference Number: 2.Quantity: 3.Fabric Name/ Number: 4.Color: 5.Repeat: 6.Content: 7.Width: 8.Finish: 9.Backing Code: Living Room x 1 yard Castel 419 E 57th Street New York NY 10022 T: 212 758 9900 F: 646 224 8695 [email protected] Donghia, 101 Henry Adams Street, Suite# 144 San Francisco, CA 94103 T:415-8617717 Refer to GF-5012 Ottoman for fabric location. Fabricator to verify quantity requirements. Approximately 5 yards. Mayreau 8006/918 Platine None 63% PO, 35% VI, 2% PA 54" Fabric must be treated with Crypton finish for soil and stain repellency. Fabric Backing as required and as recommended by fabric supplier. GF-5012.1 Fabric @ Ottoman (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 8 of 9 10.Abbrasion: 11.Fabricaton Requirements: 12.Submittal Requirements: 51,000 Wyzenbeek Requirments: -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF-5012.1 Fabric @ Ottoman (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 8 of 9 GF-5013.1 Fabic @ Dining Chair Areas Manufacturer: Local Representative: 1. Reference: 2. Quantity: 3. Fabric Name/Number: 4. Color: 5. Repeat: 6. Content: 7. Finish: Dining Room x 2 yard Swavelle Mill Creek Fabrics, Inc. 15 East 26th St. New York, NY 10010 T. 212-5328670 F.212-481-1930 Swavelle Mill Creek Fabrics, Inc. Cassandra Conaty-Giovagnoli 211 Divisadero St. San Francisco, CA 94117 T. 415-279-1232 M. [email protected] Website: swavellehospitality.com Refer to GF-5013 Lounge Chair for fabric location. Fabricator must verify all quantity requirements. Wipeout Skintex-SF Memoir Teak Face: 100% Polyurethane Back: 100% Pollex GF-5013.1 Fabic @ Dining Chair (Page 1 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 9 of 9 8. Width: 9. Backing Code: 10. Abbtasion: 11. Fabrication Requirements: 12. Submittal Requirements: 54" Fabric Backing as required and as recommended by fabric supplier. 100,000 double rubs -All fabrics to be dimensionally stable. Fabric must be first run goods from full bolt A. Printing, dyeing and finishing methods should be appropriate for use of fabric. Fabric should be pre-shrunk, non-fading and non-crocking. -Fabric must be mildew resistant, and appropriate for tropical climates and high humidity. - Provide dye lot sample for review by designer prior to cutting and shipping fabric. Note: This fabric to be used for upholstery. Manufacturer to advise designer if there are any problems with specifying this product for the intended use. GF-5013.1 Fabic @ Dining Chair (Page 2 of 2) Qingdao Model Rooms | December 8, 2011 | Spec 9 of 9