HYPERCHARGER for YAMAHA V-STAR 650 9422

INSTALLATION
HYPERCHARGER for YAMAHA V-STAR 650
1
1
CUSTOMER SERVICE
877.370.3604 (toll free)
PARTS INCLUDED
1
1
9422
Hypercharger Assembly — Chrome
Mounting Kit Including:
1
Rubber Manifold
1
Mounting Bracket
4
M6 Aluminum Spacer
3
1/4”–20 X 5/8” Socket Head Cap Screw
3
1/4”–20 Nylock Nut
3
M6 Aluminum Tapered Bolt Cap
2
M6 X 1.0 X 30mm Socket Head Cap Screw
1
M6 X 1.0 X 16mm Socket Head Cap Screw
1
6MM Serrated Flange Lock Nut
3
M6 Flat Washer
1
18” Hose
1
90 Degree Elbow
1
5” Hose
1
Aluminum Pipe, 3/8” X 1-1/4”, Hose Splice
1
Three Way “T” Fitting — Barbed Nylon
650 V-Star Jet Kit Including:
2
#35 Pilot Jet
2
117.5 Main Jet
2
120.0 Main Jet
2
122.5 Main Jet
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND NOTICES REGARDING THE USE
AND CARE OF THIS PRODUCT.
THIS INDICATION ALERTS YOU TO THE FACT THAT
IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality.
IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY,
PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE
INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF
THE IMPORTANT INFORMATION CONTAINED IN THEM.
TOOLS SUGGESTED
Service manual, Metric and Standard Hex Wrench Sets, Metric and Standard Combination
Wrenches Sets, Phillips and Flat Tip Screwdrivers
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition. Let cool.
9422-25MC-0613
-cont.-
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
STEP 1
Read and understand all steps in the instructions before starting the installation. Park the
motorcycle on a hard, level surface and turn off the ignition. Let cool.
YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM
DURING INSTALLATION. ENSURE THAT THE ENGINE AND EXHAUST
SYSTEM HAVE FULLY COOLED TO PREVENT INJURY.
A FACTORY SERVICE MANUAL WILL BE HELPFUL IN PERFORMING THIS
INSTALLATION. DO NOT ATTEMPT TO PERFORM THIS INSTALLATION IF
YOU ARE NOT CONFIDENT IN YOUR ABILITY TO COMPLETE ALL OF THE
STEPS IN THE PROCEDURE; CONSULT A TRAINED TECHNICIAN.
IMPROPER INSTALLATION COULD RESULT IN SERIOUS INJURY OR
DEATH.
Installation of this kit REQUIRES carb re-jetting over and above what may have
already been performed for pipe installation. This is a complex procedure and we
strongly recommend that this be performed by your dealer or a competent
mechanic. If you choose to attempt this on your own, you will need the service
manual for this model as carb removal and disassembly instructions are not
provided in this literature. THE FOLLOWING JETTING RECOMMENDATIONS ARE
INTENDED AS A STARTING POINT. Optimal performance and driveability may
require fine tuning. Adjustments may be needed for higher altitudes. General rule
of thumb is one jet size smaller for every 3000-4000 feet of elevation.
Rejetting and tuning a motorcycle can be a complex task. Due to factors outside of
our control, Küryakyn will not be held liable for any labor costs incurred from
installation of this kit.
Cobra/Stock Exhaust
Main Jet 117.5
Pilot Jet 35
PMS Screw 1-1/2 Turns Out From Bottom
PIC 1
V&H Style or Open Pipes
Main Jet 120
Pilot Jet 35
PMS Screw 1-1/2 Turns Out From Bottom
B
The installation of any high performance exhaust system can cause a
“lean” fuel/air mixture. A “lean” fuel/air mixture can cause engine
overheating resulting in severe engine damage. Küryakyn
recommends rejetting carbureted bikes.
STEP 2
STEP 3
A
B
B
PIC 2
Remove the stock air cleaner and components to the point shown in
PIC.1. The stock plastic airbox adapter “A” and stock mounting brackets
“B” will remain in place.
D
Insert both flanges of the rubber adapter through the mounting bracket
as shown in PIC.2. The hardware components used for installation are
placed near their respective mounting points:
•”A” Socket head cap screw - 30mm long, tapered bolt cap, and
two spacers. The spacers are placed between the chrome, and
the stock mounting brackets.
D
B
A
C
STOCK INTAKE
CLAMP
•”B” Socket head cap screw - 15mm long , tapered bolt cap
•”C” Socket head cap screw - 30mm long, tapered bolt cap, two spacers (place between
chrome and stock brackets), and flange nut.
•”D” Mounting holes.
PAGE
2
-cont.-
HYPERCHARGER for YAMAHA
INSTALLATION
STEP 4
The opening in the adapter boot must be slipped over the flange of the stock airbox and secured
with the stock clamp. Install the mounting bracket as shown in PIC.3. Secure this
PIC 3
assembly to the bike with the hardware specified in the previous step.
STEP 5
See PIC.4. Plug the extension into the float bowl vent hose and add the short
section of hose included. This will plug into the 90 degree fitting on the back side
of the Hypercharger.
STEP 6
See PIC.5. This step can be performed without disassembling the air cleaner. The
front half was removed here for a better picture. Only the round “trap door” need
be removed. “Work” the radiused flange of the adapter into the inlet hole of the air
cleaner.
STEP 7
See PIC.6. Fold the radiused flange back to expose the three mounting holes.
PIC 4
Secure the air cleaner to the bracket using the three 1/4–20x1/2” Socket head cap
screws and Nylock nuts.
STEP 8
Replace the trap door on the Hypercharger. Connect the newly extended float
bowl vent hose to the 90° fitting installed on the back of the air cleaner. On the
left side of the engine, next to the front cylinder you’ll see the two chrome lines
that go to the fresh air pump. The small rubber hose clamped to these lines is a
vacuum hose. Find the splice in this vacuum hose. Remove the splice, and in its
place insert the enclosed “T” fitting. Run the enclosed length of vacuum hose from
this “T” fitting to the vacuum nipple on the bottom of the Hypercharger.
FLOAT BOWL
VENT HOSE
HOSE EXTENSION
PIC.6
STEP 9
Double check the tightness of all related fasteners, check for hose
clearance and check throttle for correct operation, making sure it returns
properly, before starting bike.
PIC 5
ROTATE THROTTLE AND CHECK THAT IT MOVES FREELY AND
RETURNS TO CLOSED BEFORE STARTING BIKE. FAILURE OF
THE THROTTLE TO RETURN COULD RESULT IN LOSS OF
CONTROL CAUSING SERIOUS INJURY OR DEATH.
RADIUSED
It is the installer’s responsibility to ensure that all of the fasteners
FLANGE
(including pre-assembled) are tightened before operation of the
motorcycle. Küryakyn will not provide warranty coverage on products
or components lost
PIC 6
due to improper
FIG 1
installation or lack of
maintenance.
Periodic inspection
and maintenance are
required on all
fasteners.
PAGE
3
Ride On!
HYPERCHARGER for YAMAHA
INSTALLATION