Solid Gutter Cover

Transcription

Solid Gutter Cover
NEW & IMPROVED
PMS Black
0-0-0-100
Solid Gutter Cover
HELPS KEEP LEAVES AND DEBRIS OUT OF GUTTERS.
PMS 362
71-11-100-1
PMS 7473
70-0-38-8
Works on the principle of surface tension.
Water flows around the nose of the SOLID GUTTER
COVER and into the gutter through the slotted
channel.
Will handle the heaviest of rainfall.
Helps keep leaves, pine needles, and other debris out of
the gutter.
Less debris accumulation. Leaves and debris are carried
away by wind and rain.
Easy to install 4 foot sections fit standard 4”, 5” and 6”
metal gutters.
Gutter Cover simply slides under the shingles and
hooks to the front edge of the gutter. No special tools
required.
Flex design accommodates many different pitched roofs.
Made of rigid PVC.
PMS 1805
PMS 145
0-91-100-23
0-47-100-8
Low profile
design enhances
the appearance of the
gutters while helping
eliminate clogged
gutters and
downspouts.
How It Works
Take a look.
The drip guard
shields the face of
the gutter, preventing
unsightly stains known as
tiger-striping, caused by
rain and debris dripping
down the face of
the gutter.
self-merchandising
packaging
Gutter guards
are installed on rain gutters to
help prevent leaves, twigs and
other debris from falling into the
gutters and clogging both the
gutters and downspouts.
Obstructed gutters and downspouts will prevent rain water
and melting snow from flowing
through the gutter system.
Water that cannot flow freely
can back-up and overflow the
gutter causing damage to the
landscaping and the foundation.
Damage to the roof line and the
fascia board may also occur if
water gets behind the gutter or
ice dams form under shingles.
Call today to find out
more about our full line
of rain carrying products
and accessories!
800-347-2586
Description
Pack Qty.
White
Clay
3' 5/pk
4'
4' Contractor Pack
25 pcs
5
50
853045
85320
85322
1
85304BX
85314BX
www.amerimax.com
PANTONE
CM
PMS 3005
100-
PMS Black
0-0-
PMS Black
0-0-0-100
PMS 362
71-11-100-1
Solid Gutter Cover
Installation
Simple.
•
The Gutter Cover is designed with two flexible beads that bend
to fit up to a 14-12 pitch roof. Starting at one end of
PMS 7473
70-0-38-8
the gutter, slightly lift the shingles and slide the back edge of
the Gutter Cover under the shingles, then pull the front edge
over the lip of the gutter. The flexible back edge bends to
match the pitch of the roof while the flexible front edge angles
slightly forward to allow proper water flow.
PMS 1805
SHINGLES
(Fig. A)
DRIP
GUARD
PROTECTOR
IMPROVED
NOSE
0-91-100-23
Note: Before installation, bend the flexible front edge upward slightly
at the score on the underside of the gutter cover. Make sure that the
nose of the cover is lower than the back edge (Fig. A).
PMS 145
•
IMPROVED CLIP
ATTACHMENT
0-47-100-8
For an outside or inside corner, mitre cut opposite
ends of two adjoining pieces to form a corner joint.
*In high wind areas, add stainless
steel sheet metal screws to front lip.
Two screws per length.
Applying Gutter Covers to outside corners.
Note: A splash guard may be required on outside corners, inside
corners and where a downspout from an upper roof diverts water to
the lower roof. You can also eliminate the heavy flow of water on the
roof by connecting the upper roof downspout into the lower roof gutter.
•
Capping the Gutter Cover at the end of a run is recommended,
this will help prevent birds from nesting in the gutter (Fig. B).
A
With a pair of snips cut the inside width of the gutter.
B
This dimension is based on the pitch of the roof.
Cut approximately 2 inches.
C
Notch a “V” at the bend line.
D
Bend the section down 90º to form the end cap.
B
BEND LINE
D
A
C
(END CAP)
B
(Fig. B)
ZGCSSECE
www.amerimax.com