CIH49 Integrated Camera Manual

Camera Setup
Package
A. Focus and View Angle Adjustment
The following adjustment should be made by qualified service
personnel or system installers.
1. Open the Vari-Focal Lens Cover on topside of camera head.
2. Move the zoom adjust screw to reach view angle of the image.
3. Adjust the focus forward or backward to have sharp picture on the
monitor.
4. After finished the focus and zoom adjust fix the screw to prevent
optical shift during shock or vibrations.
Camera
Instruction manual
Main Power Cable ( Main power model only )
RJ-11 Male Connector
How to make sure the Phase:
1/3 Format Interline CCD Sensor
STD-Resolution Model : 510H x 492V
Scanning Frequency
2:1 Interlace, H : 15750Hz, V : 59.94Hz
Video Output
1.0Vpp Composite Video Output / 75 Ohm BNC
Audio Output
600mVpp
DC Drive Auto IRIS Lens
BLC
Central Area For Auto IRIS Lens
White Balance
Auto White Balance ( Color Model Only )
Auto White Balance Range
2700K ~ 9100K ( Color Model Only )
SYNC System
INT / Line-Lock Selectable
Resolution
NTSC Hi-Resolution : 480 TV Line
NTSC STD-Resolution: 330 TV Line.
EIA STD-Resolution : 400 TV Line
Minimum Illumination
Hi-Resolution Model : 0.8 Lux @ F1.2 max.
S/N Ratio
Color Hi-Pixel Model : 48dB.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
STD-Resolution Model : 0.3 Lux @ F1.2 max.
WARNING
To prevent fire or electric shock hazard, do not expose this
appliance to rain or moisture.
Color STD-Pixel Model : 48dB.
B/W Hi-Resolution : 50dB.
B/W SDT-Pixel Model : 50dB.
Operation Temp.
-10°C
~ +50°C, 80% RH.
Storage Temperature
-20°C
~ +60°C, 95% RH.
Power Indicator
3Ø Green LED on Rear Panel
Power Source
9.6VDC ~ 14.4VDC / 19.2VAC ~ 28.8VAC, 60Hz
Power Consumption
Feature
4.2W Max.
BNC for Composite Video Output
RCA for Audio Output
portion on the oscilloscope.
RJ11 with Power Input / Video Output / Audio Output
5
！
EIA Hi-Resolution : 570 TV Line.
Set the oscilloscope to the vertical rate and expand the vertical sync
output signals as closely as possible.
E. Fleckless Mode
When interference from the fluorescent light source at install
environment, Switch to fleckless mode ON (FLE) to avoid this
phenomenon.
F. Back Light Compensation (BLC)
When strong, unwanted background lighting interferes with the clarity
of important areas, turn this switch to the “ON” position. The BLC is
center-balanced meaning that the BLC that compensates to the
backlight conditions outside the central area.
G. AGC Turbo
Switch to ON to increase the AGC to max. gain ( approx. 36dB).
CAMERA
Hi-Resolution Model : 768H x 494V
Output Terminal
Rotate the VR of the V-Phase to match the vertical phase for both video
LENS INTEGRATED
EIA Hi-Resolution / EIA STD-Resolution
Exposure Control
Caution:
Do not fix the lens screw too tight, otherwise the optical
mechanize unit might be damaged. Just finger tight only.
B. Level ( DC IRIS Level)
To adjust the level of DC auto iris lens.
C. Synchronization Mode Selector (INT, L/L):
Selects the camera synchronization mode in either internal sync mode
(INT) or line-lock mode (L/L). Use INT setting for special applications
only, as picture roll may occur in certain applications. It is highly
recommended to use L/L and supply the camera with 24 VAC.
Note : If the AC line contains noise (spike noise, etc.), the
stability of the vertical phase of the camera video output signal
may be disturbed.
D. V-Phase:
Line lock synchronization phase adjustment. Used to adjust the phase
when the synchronization select switch is set to “L/L”.
CIH49
NTSC Hi-Resolution / NTSC STD-Resolution
General
Pixel Element
Zoom
pcs.
pcs.
pcs.
pcs.
Specifications
Image Size
Focus
1
1
1
2
Focal length
4mm ~ 9mm
Tele : F2.4 ~ 360.
Auto Iris type
Direct Drive (DC)
Angle of View
Diagonal
92.6° ~ 39.4°
Horizontal
71.0° ~ 31.6°
Vertical
51.8° ~ 23.6°
Artistic Design.
X
X
X
X
X
X
DSP Technology Process.
X
Flickerless Mode Improves Image In Fluorescent Lighting
X
X
X
AGC Turbo Function Provide 2 Times Sensitivity.
1/3’’ Hi Performance CCD Sensor.
Integrated 4 ~ 9mm Auto IRIS Vari Focal Lens.
Allow View Angle 31.6° ~ 71.0° Horizontal.
Wide : F1.6 ~ 360.
Iris aperture
X
X
X
High Quality Picture Performance.
Wide Range of Auto White Balance.
Audio Function Included.
Quick Cabling with RJ11 Connection.
Full Operation Power Range. Dual Power 24VAC/12VDC and
100VAC ~ 253VAC.
Minimum Object Distance
50cm
External Dimension
63mm (W) x 55mm (H) x 136mm (D)
Conditions
Part Number : 531-I1001-000
Version Number : 20030920-01B
6
AC Line Lock Capability (AC Power Input).
Back Light Compensation.
1
RF EMISSIONS
2. Connect the AC power cord to an electrical outlet of AC100V ~ AC253V
50Hz/60Hz.
Notes:
z Connect the power cord firmly. The power cord should be long
enough for panning and tilting. If the cable is too short, the power
cord plug may be pulled off the camera when the camera pans or
tilts.
z Brown: Live, Reference line lock. Blue: Neutral.
z This camera voltage could accept range rated is AC90V ~ AC260V.
But recommend range is AC100V ~ AC253V.
B. Dual Power Model (12VDC/24VAC).
The series model has an AC/DC compatible input terminal. DC12V or
AC24V power supply cable can be connected to this terminal. The
camera detects the power source automatically.
Recommended wire gauge size. Φ0.65mm(AWG22), Stranded wire
0.32m ㎡(AWG22), Element wireφ0.18Min.
1. 12V DC Power Supply
Connect the power cable to the AC/DC compatible input terminal on
the rear panel of the camera. +12VDC should connect is the RED
terminal. 0VDC to the white terminal. Black terminal for Earth
connection.
2. 24V AC Power Supply
Connect the power cable to the AC/DC compatible input terminal on
rear panel of the camera.
Notes:
z If the cable is too short, the power cable may be pulled off the
camera when the camera pans or tilts.
z Red: Live, Reference line lock, Black: GND,. White: Neutral.
z Voltage range: Rated AC12V ~ AC28V. or DC10V ~ DC30V.
C. Video Cable
Connection the coaxial cable with BNC female to BNC connecter on
the rear panel of camera. Measure set the termination switch to the
75Ω position on the last monitor, and to the Hi-Z position on the other
monitors. Do not change the positions after setting.
D. Audio Connection
Connection the audio signal through the RCA connector to the rear
panel of camera.
E. RJ-11 Easy Caballing Connection
Refer below picture of the pin assign to connect 6pin multi flat cable for
system connections. While caballing, the impedances of cable must
be considering, It is recommend minimum of power input must higher
then 15VDC with 3000cm/100ft cable.
Part Descriptions
This Class B digital apparatus complies with Canadian ICES-003.
Cet Appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Power Socket,
100VAC - 250VAC Power Input
Vari-Focal Lens.
Note: This equipment has been tested and found to comply with the limits
Microphone.
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
BNC, Video Output
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
RJ-11 Connecter
RCA Connecter,
Audio Output
Terminal Block,
24VAC/12VDC Power Input
LED
Power Indication
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
Vari-Focal Lens Cover.
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
Bracket Mounting Screw
Hole. 1 / 4", 7mm deep.
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
PRECAUTIONS
Do not attempt to disassemble the camera! There are no
user-serviceable parts inside. Refer servicing to qualified service
personnel.
Handle the camera with care. Improper handling or storage could
damage the camera.
Do not expose the camera to moisture, or try to operate it in wet areas.
Should the camera become wet, immediately turn power off and refer
Cover For DIP Switch and
Function Adjust.
servicing to qualified personnel.
Never face the camera towards the sun, even when not in use! Use
caution when operating the camera in the vicinity of spotlights or other
bright lights and light reflecting objects.
Do not operate the camera beyond its temperature, humidity or power
supply ratings. Use the camera under conditions where temperatures
are within –10°C to +50°C, and relative humidity is below 80% (non
condensing).
When the camera is not in use, ensure the lens is kept properly in place
to protect the CCD sensor.
Do not touch the CCD sensor directly with your fingers. If necessary,
use soft cloth moistened with alcohol to wipe off the dust.
2
1. NC
2, DC Power input
3, NC
4, Video Output
5, Audio Output
6, GND
CONNECTION
Important Note:
Qualified service personnel or system installers should make the
installation. Ensure the power is OFF before handling the power cable,
no matter AC main power mode or low voltage AC24V/DC12V mode.
A. Main Power Model (100VAC-240VAC 50Hz) :
1. Connect the AC power cord (supplied as standard accessory) to the
power cord socket of the camera.
6pin Multi-flat cable
3
3000cm / 100ft approx.
4