NetAXS-123 Standard Enclosure Wiring Diagram

Ethernet Connection (PoE/Data)
10
1
10
RS485_1
+12VDC
1
B+ B-
NO
NO
For
Future
Use
RS485_2
NetAXS-123
PWR FAIL
V- V+
Two additional Relays and second
row of TB's only present on a 2-Door
I/O Board (3-Door System)
LEDs
DC OUT
PWR
LED
RUN
Access Control Unit
LED
A
B
POWER SUPPLY
PSC-100 AHO
COM
RD2
NC
NO
EXT
NO
HOLD B
HOLD A
IN4 (TAMPER B)
OUT4 (BZR)
IN3 (TAMPER A)
+12 V
GND
D1
OUT 3
D0
OUT2 (LED)
IN1 (REX)
COM
OUT 1
IN2 (STS)
External
Power Supply
Configuration
NO/NC
Neutral
}
DRY C
NO
NC
RETURN
EXT
+12V
NO/NC
NC
NO/NC
Dry C
Return
Ground
NO
DRY C
+12V
NO/NC
Dry C
Return
GREEN
EXT
External (EXT) Power
+12VDC
Configuration
Line
NC
RETURN
+ DC
BLUE
OR
EXT Power
Supply
(+30VDC Max)
DC
Locking
Device
Locking
Device
+
FUSE*
12VDC
+12V
RUN
LED
Tamper Switch Socket
EXT
BROWN
HOLD B
HOLD A
IN12 (TAMPER B)
BZR
+12 V
GND
D1
D0
OUT8 (LED)
IN9 (REX)
COM
IN10 (STS)
NO/NC
DRY C
NOTE: Factory defaults are 12VDC
and Normally Open (NO)
Normally Closed (NC) Normally Open (NO)
+12V
Terminal Block
RETURN
AC Power
Indicator
NO/NC
USB Connection
BLUE
DRY C
RETURN
IN6 (PWR FAIL)
IN11 (TAMPER A)
AC INPUT
OUT 9
OUT 7
COM
Please read carefully
LED
LED
IN5
BROWN
FCC-CDOC and Fire Safety and Liability Notice
RD1
+24VDC IN
Optional AC Power Inlet
Battery
Casil CA 1270
12VDC, 7amp
All field wiring except for the battery backup / charger wiring is Class 2 Power Limited.
Keep power limited wiring separate from non-power limited wiring (battery backup / charger wiring) by 0.25 inch or greater.
Enclosure must be grounded to earth ground. Refer to NetAXS-123 User Guide (800-05168) for wiring information. For technical support,
please call 1-800-323-4576 Option 2.
Do not connect to a receptacle controlled by a switch.
Honeywell S-4 suppressors must be used on all door locking hardware.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Industry Canada
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. Cet appareil numérique de la classe
B respecte toutes les exigences du Réglement sur le matériel brouilleur du
Canada.
Honeywell hereby notifies installer that card readers should never be connected to
any critical entry or exit doors, barriers, elevators, etc. without providing customers
with an alternate exit in accordance with all fire and life safety codes pertinent to
the installation. These fire and safety codes vary from city to city and you must get
approval from the local fire officials whenever using an electronic product to control
a door or barrier. Use of egress push buttons, for example, may be illegal in some
cities. In most applications, a single action exit without prior knowledge of what to
do is a life safety requirement. Always make sure that any required approvals are
in writing. Do not accept verbal approvals since they are not valid.
Honeywell also never recommends using the NetAXS™ products or related
products for use as a primary warning or monitoring system. Primary warning or
monitoring system should always be used that meet local fire and safety code
requirements. Installer should instruct and verify system testing by instructing end
user in appropriate periodic testing procedures. Failure to regularly test system
could make installer liable for damage to end user if a problem occurs.
Honeywell's liability regarding all products is limited to the selling price by
Honeywell to the installer, dealer, or distributor. Honeywell does not indemnify or
provide insurance to any other company and any installing dealer should limit their
liability in the same manner to the end customer. Honeywell especially does not
provide any warranty or fitness for use for any given application and in most cases
is not aware of specific applications or use by manufactured products. These terms
and conditions apply unless modified by a written agreement between Honeywell
and purchaser
800-06787 Rev A
Firmware Revision
Standby power for full operation requires one 12VDC, 7AHr sealed lead acid rechargeable battery, CASIL CA1270 (Honeywell P/N 3-000066).
Cabinet Location
Replace the battery every 2 to 2.5 years. The battery contains lead -- please recycle it.
Replacement Fuse Use Only: 250 Volt, 1 Amp, 5x20mm, Fast Acting, Bussman GMA Cartridge Type.
Installation Date