LEXMARK BLACK CARTRIDGE 1. Enlarge the filling

The Lid Colour of the
Cartridge Can
Change Depending
On Model Type.
Filling Hole
Printed Circuit
Print Head
LEXMARK BLACK CARTRIDGE
Lexmark: 150C, 1000, 1020 1100, 2030, 2050, 2055, 2070, 3000, 3100, 3200, 4076, 5000, 5700, 5770, 7000, 7200, 7200v, X63,
X70, X73, X80, X83, X84, X85, X85 Pro, X125, X4250, X4270, Z11, Z12, Z22, Z31, Z32, Z42, Z43, Z44, Z45, Z45se, Z51, Z52,
Z53, Z54, Z54se, Z82, Z700, Z703, Z705, Z706, Z708, Z715, F4270, P700, P704, P706, P707, P3120, P3140, P3150. Optracolor:
40, 45. Medley: 4c, 4x, 4sx. Execjet: II, IIC. OKI: 2010. Compaq SmartJet: C20, IJ200, IJ600, 300, 600, 700, 900, 1200,
Xerox: 365, 365c,470, 470cx, 480cx, 490, 570, 155C, XJ8C, XJ9C, XK35, XK-35c, XK-50, XK-50cx, C20, CW470, NC-20,
XI-470. Canon 710, Brother: 810, 840 BT: 50, 55, 60, 65, 300 Sharp WinWrite: 100, 150C, Samsung.
1. Enlarge the filling hole sufficiently to accept the steel filling tube using the screw provided.
(See diagram above). IMPORTANT: DO NOT REMOVE TOP.
2. Fill syringe with ink, insert the steel filling tube into the filling hole and push downwards into the
centre of the sponge.
3. SLOWLY inject ink, when the ink overflows from filling hole cartridge is full. Stop injecting ink
immediately. DO NOT reseal filling hole.
IMPORTANT: Clean syringe with water and dry.
4. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure no
leakage and give the ink time to fully saturate the sponge.
IMPORTANT: DO NOT LEAVE ON TISSUE.
5. Install cartridge and run a priming cycle.
(When installing the cartridge the printer may ask if the cartridge is NEW or OLD cartridge.
click on NEW to reset the printer)
IMPORTANT: For best results, refill whilst ink still remains in cartridge.
Empty cartridges should be refilled immediately.
111
The Lid on Colour &
Photo Cartridges Can
Change Depending On
Model Type.
Carefully score around
the seal of the cartridge
lid with a sharp knife
Cyan
Filling Holes
Print Head
Light Cyan
Filling Holes
Magenta
Filling Holes
Yellow
Filling Holes
Print Head
Light Magenta
Filling Holes
Black
Filling Holes
LEXMARK COLOUR & PHOTO
Lexmark: 150C, 1000, 1020 1100, 2030, 2050, 2055, 2070, 3000, 3100, 3200, 4076, 5000, 5700, 5770, 7000, 7200, 7200v, X63,
X70, X73, X80, X83, X84, X85, X85 Pro, X125, X4250, X4270, Z11, Z12, Z22, Z31, Z32, Z42, Z43, Z44, Z45, Z45se, Z51, Z52,
Z53, Z54, Z54se, Z82, Z700, Z703, Z705, Z706, Z708, Z715, F4270, P700, P704, P706, P707, P3120, P3140, P3150. Optracolor:
40, 45. Medley: 4c, 4x, 4sx. Execjet: II, IIC. OKI: 2010. Compaq Smartjet: C20, IJ200, IJ600, 300, 600, 700, 900, 1200,
Xerox: 365, 365c,470, 470cx, 480cx, 490, 570, 155C, XJ8C, XJ9C, XK35, XK-35c, XK-50, XK-50cx, C20, CW470, NC-20,
XI-470. Canon 710, Brother: 810, 840 BT: 50, 55, 60, 65, 300 Sharp WinWrite: 100, 150C, Samsung.
1. The filler holes are located under the coloured top of the cartridge. This top needs to be
removed before filling. Use a penknife or Stanley knife to break the seal by carefully scoring
around all four edges of seal. (Colour & Photo cartridge only)
2. Assemble syringe and steel filling tube and fill with appropriate colour ink.
3. Insert the steel filling tube into the appropriate filling hole. (See diagram above).
Push downwards into the centre of the sponge.
IMPORTANT: Cartridge contains a sponge and a slight resistance may be felt.
4. SLOWLY inject ink. When ink overflows from filling hole or starts to leak from print heads,
cartridge is full. Stop injecting immediately. Blot printer head with tissue before continuing to fill
next colour.
IMPORTANT: Clean syringe with water and dry before refilling next colour.
5. After refilling reseal the top. The best way to secure the top is to stick tape from one side, over
the top and down the opposite side.
6. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure no
leakage and give the ink time to fully saturate the sponge.
IMPORTANT: DO NOT LEAVE ON TISSUE.
7. Install cartridge and run a priming cycle.
(When installing the cartridge the printer may ask if the cartridge is a NEW or OLD
cartridge. click on NEW to reset the printer)
IMPORTANT: For best results, refill whilst ink still remains in cartridge.
Empty cartridges should be refilled immediately.
112
Carefully Lever the
cartridge lid with a
sharp knife i.e. Pen
knife.
Colour Cartridge
With Lid Removed
Magenta
Filling Holes
Yellow
Filling Holes
Cyan
Filling Holes
Print Head
LEXMARK
Lexmark: Z55, Z55se, Z65, Z65n, Z65p, X5100, X5130, X5150,
X5190, X6150, X6170, X6190Pro. Dell: 740, 940, 960.
1. The filler holes are located under the coloured top of the cartridge. This top needs to
be removed before filling. Use a penknife or Stanley knife to break the seal by carefully
scoring around all four edges of seal. (Colour cartridges only).
2. Assemble syringe and steel filling tube and fill with appropriate colour ink.
3. Insert the steel filling tube into the appropriate filling hole. (See diagram above).
Push downwards into the centre of the sponge.
IMPORTANT: Cartridge contains a sponge and a slight resistance may be felt.
4. SLOWLY inject ink. When ink overflows from filling hole or starts to leak from print
heads, cartridge is full. Stop injecting immediately. Blot printer head with tissue before
continuing to fill next colour.
IMPORTANT: Clean syringe with water and dry before refilling next colour.
5. After refilling reseal the top. The best way to secure the top is to stick tape from one side,
over the top and down the opposite side.
6. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure
no leakage and give the ink time to fully saturate the sponge.
IMPORTANT: DO NOT LEAVE ON TISSUE.
7. Install cartridge and run a priming cycle. When installing the cartridge the printer
may ask if the cartridge is a NEW or OLD cartridge. click on NEW to reset the printer.
IMPORTANT: For best results, refill whilst ink still remains in cartridge.
Empty cartridges should be refilled immediately.
113
Filling Hole
Print Head
LEXMARK
Lexmark: Z55, Z55se, Z65, Z65n, Z65p, X5100, X5130, X5150,
X5190, X6150, X6170, X6190Pro. Dell: 740, 940, 960.
1. Enlarge the filling hole sufficiently to accept the steel filling tube using the screw provided.
IMPORTANT: DO NOT REMOVE TOP.
2. Fill syringe with ink, insert the steel filling tube into the filling hole and push downwards into the
centre of the sponge.
3. SLOWLY inject ink, when the ink overflows from filling hole cartridge is full. Stop injecting ink
immediately. DO NOT reseal filling hole.
IMPORTANT: Clean syringe with water and dry.
4. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure no
leakage and give the ink time to fully saturate the sponge.
IMPORTANT: DO NOT LEAVE ON TISSUE.
5. Install cartridge and run a priming cycle. (When installing the cartridge the printer may ask if
the cartridge is a NEW or OLD cartridge. click on NEW to reset the printer)
IMPORTANT: For best results, refill whilst ink still remains in cartridge.
Empty cartridges should be refilled immediately.
114
Remove Lid
Print Head End
Colour Cartridge
With Lid Removed
Yellow
Filling Holes
Magenta
Filling Holes
Cyan
Filling Holes
Print Head
LEXMARK
Lexmark: I3, Z13, Z23, Z24, Z25, Z25I, Z33, Z34, Z35, Z513, Z515, Z517,
Z600, Z601, Z604, Z605, Z612, Z615, Z617, X72, X74, X75, X1100, X1130, X1150, X1160,
X1170, X1180, X1185, X1190, X2200, X2230, X2250. 4126.
Lexmark Jetprinter: A10. Dell: 720, 920.
1. The filler holes are located under the coloured top of the cartridge. This top needs to
be removed before filling. Use a penknife or Stanley knife to break the seal by carefully
scoring around all four edges of seal. (Colour cartridge only)
2. Assemble syringe and steel filling tube and fill with appropriate colour ink.
3. Insert the steel filling tube into the appropriate filling hole. (See diagram above). Push
downwards into the centre of the sponge.
IMPORTANT: Cartridge contains a sponge and a slight resistance may be felt.
4. SLOWLY inject ink. When ink overflows from filling hole or starts to leak from print
heads, cartridge is full. Stop injecting immediately. Blot printer head with tissue before
continuing to fill next colour.
IMPORTANT: Clean syringe with water and dry before refilling next colour.
5. After refilling reseal the top. The best way to secure the top is to stick tape from one side,
over the top and down the opposite side.
6. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure
no leakage and give the ink time to fully saturate the sponge.
IMPORTANT: DO NOT LEAVE ON TISSUE.
7. Install cartridge and run a priming cycle. (When installing the cartridge the printer may
ask if the cartridge is NEW or OLD cartridge. click on NEW to reset the printer).
IMPORTANT: For best results, refill whilst ink still remains in cartridge.
Empty cartridges should be refilled immediately.
115
Filling Hole
Print Head
LEXMARK
Lexmark: I3, Z13, Z23, Z24, Z25, Z25I, Z33, Z34, Z35, Z513, Z515, Z517,
Z600, Z601, Z604, Z605, Z612, Z615, Z617, X72, X74, X75, X1100, X1130, X1150, X1160,
X1170, X1180, X1185, X1190, X2200, X2230, X2250. 4126.
Lexmark Jetprinter: A10. Dell: 720, 920.
1. Enlarge the filling hole sufficiently to accept the steel filling tube using the screw provided.
IMPORTANT - DO NOT REMOVE TOP.
2. Fill syringe with ink, insert the steel filling tube into the filling hole and push downwards into the
centre of the sponge.
3. SLOWLY inject ink, when the ink overflows from filling hole cartridge is full. Stop injecting ink
immediately. DO NOT reseal filling hole.
IMPORTANT: Clean syringe with water and dry.
4. Leave cartridge to stand overnight on a protective, non-absorbent surface, this will ensure no
leakage and give the ink time to fully saturate the sponge.
IMPORTANT: DO NOT LEAVE ON TISSUE.
5. Install cartridge and run a priming cycle. (When installing the cartridge the printer may ask if
the cartridge is NEW or OLD cartridge. click on NEW to reset the printer)
IMPORTANT: For best results, refill whilst ink still remains in cartridge.
Empty cartridges should be refilled immediately.
116
117