poster short course - Institut Latihan Perindustrian Kangar

SENARAI KURSUS
JANGKA PENDEK
2010
JUN - DISEMBER
Institut Latihan Perindustrian Kangar
NO.
COURSE
CODE
COURSE TITLE
DURATION
(HOUR)
FEES (RM) *
NO. OF
PARTICIPANT
1
AP01
Basic Pneumatic
16
255.00
10
Introduction to Pneumatic system, introduction to various part of pneumatic equipment, production of compressed air, sign and
symbol used for pneumatic component. Symbol and schematric diagram for pneumatic component and their user. Function and
working principle of various type of valve, cylinder and other accessories.
10
Introduction to electro-pneumatic system: Introduction to various part of electro-pneumatic equipment, production of compressed
air, sign and symbol used for electro-pneumatic components: Symbol and schematic diagram for piston and cylinder, control valve
etc, designation symbol for component, electro-pneumatic component and their uses: Function and working principle of various
type of valve, cylinder and other accessories, pneumatic component and their uses: Function and working principle of various type
of valve, cylinder and other accessories.
10
Introduction to hydraulics, hydraulics power system: Power pack system, hydraulic fluids properties and uses, hydraulics power
system: Power pack system, hydraulic fluids properties and uses, element and standard symbol of hydraulics system, hydraulics
accessories: Type and uses of hydraulics equipment and component, basic hydraulics circuit: Development of basic hydraulics for
controlling hydraulics cylinder, motors and other actuators, development of simple hydraulics diagrams, basic hydraulics practical:
Setting up simple hydraulic circuit according to diagrams.
2
3
AP02
AP03
Basic Electro-Pneumatic
Basic Hydraulic
16
16
255.00
255.00
COURSE CONTENT
TRAINING CALENDAR **
JUNE
JULY
AUGUST
22 ~ 23
12 ~ 13
AP04
Basic Electro-Hydraulic
16
255.00
10
5
AP05
Programmable Logic Control
16
255.00
10
Introduction to PLC, function and use of PLC component, circuit development and circuit diagram design, documentation and
software management, communication between personal computers and PLC, programming in ladder diagrams and
troubleshooting problem and basic control system.
15 ~ 16
5~6
6
EP01
Basic Electronic
20
250.00
8
Introduction to basic electricity, electronics and digital logic, operation of the devices, schematic diagram and perform test and
measurement with a VOM, oscilloscope and signal generator.
22 ~ 23
5~6
7
EP02
Basic Programmable Logic
Controller
20
250.00
8
To understand the basic operation and mechanism of PLC. Learn some basic PLC Programming. Basic mechanism of PLC.
Basic operation of programmable console. Some application of basic execution commands. Learn simple operation of
programming.
8
EP03
Basic Of Control Motor Curcuit
16
250.00
8
To perform basic of the principles, types and function of Three Phase Inductor Motor Starter components.
10
Calibrate temperature switch using temperature probe, calibrator and multimeter so that the set point of the switch meets process
specification. Calibrate level switch using level stand pipe indicator and multimeter so that the set point of the switch meets
process specification. Functional check on flow switch using simulated flow and multimeter so that the flow switch is functioning as
per specification. Functional check on solenoid valve using air/power supply source and pressure gauge so that the solenoid valve
is functioning to specification
Basic Calibrate Switches And
Solenoid Valve
16
250.00
NOV
DEC
25 ~ 26
30 ~ 1
4
IP01
OCT
23 ~ 24
Introduction to electro-hydraulics, electro-hydraulics power system: Power pack system, electro-hydraulic fluids properties and
uses, electro-hydraulics power system: Power pack system, electro-hydraulic fluids properties and uses, element and standard
symbol of electro-hydraulics system, electro-hydraulics accessories: Type and uses of electro-hydraulics equipment and
component, basic electro-hydraulics circuit: Development of basic electro-hydraulics for controlling electro-hydraulics cylinder,
motors and other actuators, development of simple electro-hydraulics diagrams, basic electro-hydraulics practical: Setting up
simple electro-hydraulic circuit according to diagrams.
9
SEPT
11 ~ 12
7~8
12 ~ 13
28 ~ 29
14 ~ 15
9 ~ 10
25 ~ 26
2~3
7~8
20 ~ 21
10
IP02
Basic Maintainance Instrument
Devices
16
250.00
6
Install pneumatic transmition lines and components using hook-up diagram, tubing bender, cutter and leak detection solution so
that it provides air supply to the transmitter for signal transmition. Install electrical signal transmition lines and components using
wiring diagram, hand tools and multimeter so that it provides electrical power and signal transmition to the instruments. Calibrate
pressure gauge using pressure calibrator and hand tools so thet the acuracy of the reading meets manufacturer's specification.
Functional check on limit switch appropriate triggering devices and multimeter so that function as per plant requirement. Service
process regulator using pressure gauge and hand tools so thet the process regulator is in working condition dan meets
manufacturer's specification.
11
FL01
Basic Arc Welding
16
250.00
12
Fundamental of arc welding-safety procedures setting up and operation procedure of arc welding machines, identification and
selection of electrodes and their applications in welding work, welding technique-beading, padding on flat and round bar. Welding
of lap, corner and tee fillet welds, testing welds-destructive and non-destructive testing .
12
FL02
Intermediate Arc Welding
16
250.00
12
Welding variable and techniques beading in horizontal and vertical up, type of butt-weld, edge preparation and vertical up,
meaning of arc blow and polarity, welding of butt-joints in 1G, 2G and 3G ( flat, horizontal - vertical and vertical-up position), testing
welds-destructive testing .
18 ~ 19
13
FL03
Basic Metal Fabrication
16
250.00
12
Introduction to metal fabrication practices and safety precautions. Layout procedures, selection and use of shop tools and
fabrication machinery including shears, hand, grinders, etc. Set up operations of oxy-acetylene welding/cutting equipments. Set up
and operations of arc-welding machine. Welding and flame cutting, development drawings. Fabrication of workpieces by using
templates, such as cone hopper, square and round elbow and T-joint.
4~5
14
FL04
Intermediate Metal Fabrication
16
250.00
12
Set up and operation of oxy-acetylene welding/cutting equipment's and arc welding machine, development drawing. Preparation of
templates, fabrication work: Fabrication of square to round shape workpiece, joining pipes in 90 degrees three pitch turn and ybranch, fabricating three-piece rectangular to round elbow .
15
FL05
Advanced Metal Fabrication
16
250.00
12
Type of butt-joints and edge preparation, techniques of pipe welding, welding of rotated pipe in, horizontal
(1G) position,
welding of pipe in vertical (2G) position, welding of fix pipe in, horizontal (5G) positions, types of weld defects and weld test .
16
FL06
AutoCAD 2007 - Part 1
16
150.00
12
Getting started, display commands, CAD Tools & drawing setup, basic drawing command, basic edit commands, layers, CAD
construction techniques, creating text & defining styles, blocks & drawing import/export options dimensions, crosshatching,
printing & ploting basics, introduction to paper space .
17
FL07
AutoCAD 2007- Part 2
16
150.00
12
Advanced drawing techniques, managing your system, inserting graphics, working with attributes, advanced dimensioning, paper
space and plotting, introduction to customization, introduction to 3D .
18
FL08
AutoCAD 2007 - 3D
16
150.00
12
AutoCAD 3D productivity, basic 3D concepts, coordinate system & viewing, entities in 3D space, surfaces, creating 3D solids,
editing & analyzing 3D solids, model space & paper space, concepts visualing the finishing model.
19
FL09
Oxy-Acetylene Welding Cutting
16
250.00
16
Work on the steel plate with a several thickness, groove weld in: Horizontal position, vertical position, uphill position cutting
straight/round on plate, work on the steel pipe with several diameters and thickness, groove weld in rotation, vertical position and
all position, preparation before welding, defect and remedy and welding control.
12
Introduction to blue print, the alphabet of line, types of lines and their uses, lettering and dimensioning, freehand sketches,
principles of projection drawing, pictorial drawing, sectional views, title block, list of material, drawing notes, drawing changes,
thread representation/specification, specification and call-out for machine processes. Broken out, partial, removed and revolved
sections, tolerances, allowances and dimensioning, limits and fits, geometric tolerancing, auxiliary views, welding symbols and
castings, Irrelationship and sequence of components in assembly and sub assembly procedure, basic AutoCAD 2D .
9
Material: Carbon steel position: 1F1G or/ and 2F2G or/ and 3F3G theoretical : Introduction to gas metal arc welding, safety and
health of welders, selecting the equipment and material, set up operation and shut down procedure, practical : Exercise on fillet
joint and single V butt joint in vertical position, material positioning and tack weld, perform fillet joint and single V butt joint, test and
visual inspections, in accordance with the position required by the company.
9
Position: 1F/1G or 2F/2G and 3F/3G, theoretical: Introduction to GTAW (only for 1F/1G course ), the welding characteristics of
carbon steel, safety and health of welders, selecting the equiment and meterial, set up operation and shut down procedure,
practical, stringer bead without and with filler metal on 1.5mm D20 carbon steel in flat/horizontal/vertical position, fillet weld lap
joint without and with filler metal on 1.5mm low carbon steel plate (for 1G and 2G), fillet weld T-joint without and with filler metalon
1.5mm low carbon steel plate in the position required by the company, fillet weld outside corner joint without and with filler metal
on 1.5mm low carbon steel plate in flat position (only for 1F), groove weld single V butt joint on 6mm low carbon steel plate in
vertical position (3G) (root and hot pass only), groove weld square butt joint with filler metal on 1.5mm low carbon steel plate in
the required position, inspection and testing welds, report, in accordance with the position required by the company.
9
Material: Aluminium position: 1G and 2G theoretical: Safety and health of welders, selecting the equipment and materials, set up
operation shut down procedure, the joint designs for pipe welding and pipe welds quality, practical, square butt joint on diameter
50mm sch. 10 aluminium pipe in 1G position, groove weld single V butt joint on diameter 50mm sch. 40 aluminium pipe in 1G
position, square butt joint on diameter 50mm sch.10 aluminium pipe in 2G position, groove weld single V butt joint on diameter
50mm sch. 40 aluminium pipe in 2G position, inspection and testing welds and report .
1~2
9
Material: Carbon steel position: 1F1G or/ and 2F2G or/ and 3F3G theoretical : Introduction to gas metal arc welding, safety and
health of welders, selecting the equipment and material, set up operation and shut down procedure, practical : Exercise on fillet
joint and single V butt joint in vertical position, material positioning and tack weld, perform fillet joint and single V butt joint, test and
visual inspections, in accordance with the position required by the company.
8~9
20 ~ 21
20
21
22
23
24
FL10
Blue Print Reading
FL11
Gas Tungsten Arc Welding Carbon Steel
FL12
Gas Tungsten Arc Welding Stainless Steel
FL13
Gas Tungsten Arc Welding Aluminium
FL14
Gas Metal Arc Welding - Carbon
Steel
16
16
16
16
16
150.00
300.00
300.00
300.00
300.00
25
FL15
Gas Metal Arc Welding Stainless Steel
16
300.00
9
Position: 1F/1G or/ and 2F/2G or/ and 3F/3G, theoretical: Introduction to GMAW (only for 1F/1G course ), the welding
characteristics of carbon steel, safety and health of welders, selecting the equiment and material, set up operation and shut down
procedure, practical, stringer bead without and with filler metal on 1.5mm low carbon steel in flat/ horizontal/ vertical position, fillet
weld lap joint without and with filler metal on 1.5mm low carbon steel plate (for 1G and 2G), fillet weld tee joint without and with
filler wire metal on 5mm low carbon steel plate in the position required by the company, fillet weld outside corner joint without and
with filler metal on 5mm low thickness low carbon steel plate in flat position (only for 1F), Groove weld single V butt joint on 6mm
low carbon steel plate in vertitcal position (3G) (root and hot pass only), groove weld square butt joint with filler wire metal on 5mm
low carbon steel plate in the required position, inspection and testing welds, report,in accordance with the position required by the
company.
26
FL16
Development Drawing
16
150.00
12
How to use radial line to develop template, knowledge mechanical drawing, using of drawing tools, method of developments,
preparation templates . How to use trigulation method to develop template, knowledge mechanical drawing, using of drawing
tools, method of developments, preparation templates .
10
This course is designed to enable participants to acquire knowledge and skill in operation of vertical Milling Machine. Participants
will be thaught theory and practical skill of various milling techniques.
CONTENT; Workshop safety. Operation of machine. Rough and finish milling a blank with six surface. Milling slot, step, shoulder
and grove. Pocket milling. Inspection and maintenance. Assemble part techniques.
27
CNC01
Perform Milling Operation
32
250.00
24 ~ 25
20 ~ 21
1~2
27 ~ 28
21 ~ 22
17 ~ 18
27 ~ 28
2~3
27 ~ 28
11 ~ 12
8~9
16 ~ 17
Overview: Features and component of CNC Milling. Workpiece clamping system and tool clamping system. Type of cutting tool
used in CNC Milling. The controller of CNC Miliing.
Programming: Introduction to the programming codes. The program structure and machining sequence. Write a simple CNC
Milling program refering to part drawing given.
Workpiece
Application:
Tool setting
the machine.
Program
editing
on the machine.
Overview: Features
and on
component
of CNC
Turning.
Workpiece
clamping system
andmachining.
tool clamping system. Type of cutting tool
12 ~ 15
11 ~ 14
19 ~ 23
18 ~ 22
28
CNC02
CNC Milling
40
300.00
10
29
CNC03
CNC Turning
40
300.00
10
30
CNC04
CNC Wire Cut
40
300.00
10
31
CNC05
CNC Die Sinking
40
300.00
10
Knowledge on type of electrode. Knowledge on type of electrode holding devices. Knowledge on operational feature of EDM Die
Sinking Machine and function. Practical exercise on Die Sinking.
32
TM01
Microsoft Word
16
100.00
15
Introduction to Microsoft Word, editing document, bullets, auto numbering and multilevel, formatting document, table, columns and
border, columns, setting on word, insert picture, printing document, merging document.
28 ~ 29
25 ~ 26
33
TM02
Microsoft Excel
16
100.00
15
Introduction to Microsoft Excel, building a worksheet, correcting data and using help, adding formulas, cut, copy and paste, More
on summation, inserting and deleting rows and columns, formatting a worksheet, printing a worksheet, working with charts, pivot
table, sorting data.
30 ~ 1
27 ~ 28
5~6
1~2
7~8
3~4
used in CNC Turning. The controller of CNC Turning.
Programming: Introduction to the programming codes. The program structure and machining sequence. Write a simple CNC
Turning program refering to part drawing given.
Application: Tool setting on the machine. Program editing on the machine. Workpiece machining.
Overview: Features and component of CNC Wire Cut . Knowledge on type of wire, installation and setting CNC Wire Cut.
Workpiece setting. The controller of CNC Wire Cut.
Programming: Introduction to the programming codes. The program structure and machining sequence. Write a simple CNC Wire
Cut program refering to part drawing given.
Application: Wire setting on the machine. Program editing on the machine. Workpiece machining.
2~6
8 ~ 12
20 ~ 24
4~8
34
TM03
Microsoft Powerpoint
16
100.00
15
Introduction to Microsoft Powerpoint, creating a new presentation, entering and adding text to your presentation, moving text and
objects, changing text attributes, save, undo and redo your presentation, add, delete and move slides, viewing your slide show,
creating a new presentation using the auto wizard, opening and printing presentation, adding clip-art, working with slide and layout,
drawing objects, working with draw objects, slide transitions, adding animation and sound.
35
TM04
PC Assembly - Basic
16
200.00
5
Introduction to PC Component and hardware. Theory on hardware assembly technique. Practice on assemble hardware for
Personal Computer and basic installation of Operating System
36
TM05
Basic Web Design
16
100.00
15
Introduction web design, introduction to HTML code, Create forms,Insert Images, Publish HTML. Introduction for Front PagesCreate new website, Entering and Inserting text in a webpage, Formating text, Apply table, frame and form function, Apply
paragraph Style, Import Pages into website, Previewing Website. Base Website- Downdload file to base website.
3~4
23 ~ 24
37
TM06
Basic Internet and Email
16
100.00
15
Introduction to the internet and email. Getting connected to the internet. Internet application and understanding the World Wide
Web. Create email account and getting connected to email functions.
25 ~ 26
25 ~ 26
10
This course is designed to enable participants to acquire knowledge and skill in operation of Lathe Machine. Participants will be
thaught theory and practical skill of turning techniques.
CONTENT; Workshop safety. Part and function of lathe machine. Facing, longitudinal step turning. Drilling, boring. Taper turning.
Thread cutting. Knurling, Grooving, Chamfering and Parting off. Assemble part techniques.
2~5
8 ~ 11
38
MI01
Perform Turning Operation
32
250.00
* Yuran bagi setiap peserta tidak termasuk makanan & penginapan. Tambahan yuran akan dikenakan sekiranya terdapat permintaan terhadap makanan & penginapan.
** Tarikh latihan boleh berubah berdasarkan jumlah permohonan peserta yang diterima. Sebarang perubahan akan dimaklumkan kepada perserta yang terlibat. Kursus juga boleh dilaksanakan pada hujung minggu.
CARA PERMOHONAN
1. Muat turun borang permohonan dari laman web : www.ilpkangar.gov.my
2. Borang yang lengkap dihantar melalui fax/ pos selewat-lewatnya 3 minggu sebelum latihan bermula ke Bahagian
Kawalan Kualiti Latihan ILP Kangar.
3. Peserta yang berjaya dalam permohonan akan dihubungi oleh pihak ILP Kangar. Yuran perlu dijelaskan secara
Kiriman Wang/ Bank Draft/ Wang Pos kepada Pengarah ILP Kangar selewat-lewatnya 1 minggu sebelum kursus
bermula.
Tel: 04-9794000
Faks: 04-9777663
Laman Web: http://www.ilpkangar.gov.my
Email : [email protected]