Services Unlimited, Inc./ Parts Guru

Instructions to open Jura S series
Instructions to open the Jura S90 to perform repair and maintenance
Pa
rts
G
ur
u.
co
m
Applies to Jura S-Series, Jura X90/95 and Capresso C3000
Safety:
Before opening the device, unplug the power cord and make sure that the device is
disconnected.
Disclaimer:
Services Unlimited Inc./Parts Guru͕ŝƚƐƐƚĂĨĨŽƌĂĨĨŝůŝĂƚĞƐ assumes no liability for any
damages related to repairing the machine.
'PS+VSBQBSUTSFQBJSTUFDITVQQPSUDPOUBDU
Services Unlimited, Inc./ Parts Guru
209 Walnut street, Lansdale PA 19446
215-361-7000 email: [email protected]
Online store: www.shop.partsguru.com
Courtesy of Services Unlimited Inc./Parts Guru
email: [email protected]
Page 1 of 7
Instructions to open Jura S series
1. Open the cover of the bean container, and remove the coffee chute cover, the water
tank and drip tray and drip tray and coffee grounds container.
u.
co
m
Cup Warmer Plate
Pa
rts
G
ur
2. Remove the 4 housing screws using Torx size screw driver and remoe the cup warmer
plate
Grind
Adjustment Knob
3. Pull of the grinding knob. Unscrew the 3 housing screws and remove the housing
cover
Courtesy of Services Unlimited Inc./Parts Guru
email: [email protected]
Page 2 of 7
Instructions to open Jura S series
co
m
Brew Group
Encoder Clamp
Pa
rts
G
ur
u.
4. Carefully remove the brew group encoder clamp as it may fall inside the machine.
5. Use the oval head key to remove the oval head screws from the back of the machine.
For Jura parts, repairs & tech support, contact:
Services Unlimited, Inc./ PartsGuru
209 Walnut street, Lansdale PA 19446
215-361-7000 email: [email protected]
Online store: www.shop.partsguru.com
Page 3 of 7
Instructions to open Jura S series
Steam Valve
Knob
co
m
Steam Pipe
Front Door
Screw
u.
6. Remove the front door screw as circled above. The other screws can be left in place
Pa
rts
G
ur
Steam Valve Mounting Plate
Mounting Plate
Steam Valve
Knob
Steam Pipe
7. Remove the steam knob by using the flat screw driver. Carefully push out the steam
knob from each side, as indicated in the green arrows.
Carefully lift the mounting plate to unlatch the steam valve assembly from the mounting
plate. Door should open about halfway.
Courtesy of Services Unlimited Inc./Parts Guru
email: [email protected]
Page 4 of 7
co
m
Instructions to open Jura S series
ur
u.
8. To unlock the front door, run in the blue marked point using the medium screw driver
and unlatch the hose connector. Lift the retaining tab very gently until the lock is
released. Pull the connector with the other hand to the back.
Rear View
Pa
rts
G
Front View
9. The front and rear of the machine is now exposed and accessible to perform
maintenance and repairs.
Courtesy of Services Unlimited Inc./Parts Guru
email: [email protected]
Page 5 of 7
Instructions to open Jura S series
co
m
Instructions to close the machine after maintenance and repair
First, connect the hose assembly to the height adjustable coffee spout. Ensure that the
retaining tab properly locks into the connector.
O-Ring Steam Pipe
Connection
Mounting Plate
G
ur
u.
O-Ring Steam Pipe
Pa
rts
Replace the steam pipe and steam pipe connection o-rings.
Re-install the steam pipe and steam pipe connection and connect the pins into the slots on
the front door. Ensure the steam valve is sucessfully locked in to the mounting plate from
the top.
Replace the steam valve knob; push it in the hole. It should lock in easily.
For Jura parts, repairs & tech support, contact:
Services Unlimited, Inc./ PartsGuru
209 Walnut street, Lansdale PA 19446
215-361-7000 email: [email protected]
Online store: www.shop.partsguru.com
Courtesy of Services Unlimited Inc./Parts Guru
email: [email protected]
Page 6 of 7
Instructions to open Jura S series
Grind Adjustment Key
Encoder Clamp
Insulation
co
m
Hoses
u.
Before replacing the top cover, re-install the encoder clamp. Ensure that insulating plate is
not damaged, the hoses are not bent or squashed.
Insert the cup warmer plate and tighten the screws.
Replace the water tank , used coffee container, and the drip tray.
ur
For Jura parts, repairs & tech support, contact:
Services Unlimited, Inc./ PartsGuru
Pa
rts
G
209 Walnut street, Lansdale PA 19446
215-361-7000 email: [email protected]
Online store: www.shop.partsguru.com
Courtesy of Services Unlimited Inc./Parts Guru
email: [email protected]
Page 7 of 7