Evanescence

Evanescence ADDENDum
to the owner’s Manual
Important information for the installer
and the owner
Included:Freestanding Evanescence baths installation instructions
important: To be kept for the owner
TM
E va n escen ce AD D E ND U M to o w n er’s ma n ual | tMU ® & tM SU TM
TH ER MO MASSEUR ®
TMU ® & TMSU TM
Eva n esce n ce 6 6 3 4 & Eva nesce nce O va l 6636 - pa r t s a nd t o o l s - si t e p repa r atio n
Evanescence 6634 & Evanescence Oval 6636 freestanding
PARTS AND TOOLS
A. PARTS INCLUDED
A-1
Floor anchoring
A-2
Installation template
B. TOOLS REQUIRED
B-1
48-inch level
B-2
Caulking gun
A-1 x 2
A-2 x 1
B-3Silicone
B-1
B-2
B-3
Evanescence 6634 & Evanescence Oval 6636 freestanding
B-4
Evanescence Freestanding models require
a 13” x 14” (33 cm X 36 cm) compartment
for the drain, distance air inlet, and space
for control cables and options. Refer to
the installation template.
2
1 800 463.2187
SiTE PREPARATION
B-5
ACCESS AND AIR INLET
For these model, the turbine is not installed on the bathtub.
Determine a location near the bathtub at a maximum distance
of 15 feet or (4.6 metres) under the floor, in a cabinet or any other
location to conceal the turbine and optional accessory casings.
The location chosen must also be accessible and allow sufficient air
intake for the turbine.
(Refer to the TURBINE–DISTANCE INSTALLATION section of the
Owner’s Manual).
From 8 a.m. to 8 p.m. Monday to Thursday (EST) . From 8 a.m. to 5 p.m. on Friday (EST)
Printed in Canada. Copyright © April 2014 BainUltra Inc. All rights reserved. 45200599
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
Eva n escen ce A D D E N D U M t o o w n e r ’s ma n ual | tMU ® & tMSU TM
E vanescence 6 6 3 4 & Eva n esce n ce O va l 6636 - I ns ta l l at i o n
TMU ® & TMSU TM
Evanescence 6634 & Evanescence Oval 6636 freestanding
INSTALLATION
1. LOCATION
1-1
1-2
2-1
2-2
1-1Place the installation template on the ground
at the chosen location.
1-2Align the position of the overflow drain with
the floor drain and ensure that the compartment size corresponds to requirements.
3-1
1-3Mark the location of the anchor point screws.
3-2
2-3
3-3
2-4
2-5
3-4
3-5
Evanescence 6634 Installation Template
1-4Remove the installation template and screw
in the anchor points in the marked locations.
2. installation of bath
2-1Assemble the provided drain on the bathtub.
Use the overflow assembly provided for
the junction to the drain T-joint. Ensure
watertightness. This operation is much
easier to complete when the bathtub rests
on its side. Place a cover or protective
cardboard on the floor before positioning
the bathtub on its side.
2-2Apply a joint of silicone under the edge
of the base of the bathtub.
Evanescence Oval 6636 Installation Template
1-1
1-2
2-1
2-2
3-1
3-2
2-3
3-3
1-1
1-2
2-2
2-4
2-5
2-1
3-4
3-5
3-1
3-2
Evanescence 6634
Evanescence Oval 6636
www.bainultra.com
Printed in Canada. Copyright © April 2014 BainUltra Inc. All rights reserved. 45200599
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
3
2-3
3-3
E va n escen ce AD D E ND U M to o w n er’s ma n ual | tMU ® & tM SU TM
TMU ® & TMSU TM
E va nesce nce 6634 & E va nesce nce O va l 6636 - I ns ta l latio n
Evanescence 6634 & Evanescence Oval 6636 freestanding
Installation
1-1
2. installation of bath
1-2
(Cont’d)
2-3Install the bathtub on the anchor 2-1
points 2-2
fastened to the floor and immediately wipe
away any excess silicone. Connect the drain.
3-1
2-4Install the turbine according to the
instructions in the TURBINE – DISTANCE
INSTALLATION section of the manual.
The air inlet is located to the right of the
bathtub drain and, if applicable, control
and option connection cables to the right.
Connect control and option cables
if applicable. For Geysair-equipped
baths, also run the water hose and
electrical wiring through the floor.
3-2
2-3
3-3
2-4
2-5
3-4
3-5
Evanescence 6634
2-5
For Geysair-equipped baths, connect
the Geysair electrical wire supplied with
the male connector with the turbine cable
equipped with the female connector. Test
for grounding continuity between the
bath grounding terminal
and the
bath power supply. Failure to perform
the grounding continuity test could
result in serious personal injury.
1-1
1-2
Evanescence Oval 6636
2-1
3-1
2-2
3-2
2-3
3-3
2-4
2-5
3-4
3-5
Turbine Female
Connector
NOTES
• To install the Evanescence Freestanding
on a concrete slab with no place for the
passage of the air inlet pipe to the
bathtub: drill a hole 1 5/8 inches in
diameter in the skirt. IMPORTANT: drill
the hole 1 1/2 inches above floor level
and protect the bathtub with a piece
of wood placed behind the location
to be drilled.
4
Ground Wire
for the Bathtub
1 800 463.2187
Geysair Male
Connector
From 8 a.m. to 8 p.m. Monday to Thursday (EST) . From 8 a.m. to 5 p.m. on Friday (EST)
Printed in Canada. Copyright © April 2014 BainUltra Inc. All rights reserved. 45200599
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.