FTN-TP-070 3P LED Lamp

Transcription

FTN-TP-070 3P LED Lamp
Signcomplex
we bring innovation and give impression
3P LED Lamp
FTN-TP-070
Description:
This product use durable long life span LED as light source, smooth light without glare, simple looking design.
Corrosion-proof, water-proof and dust-proof, IP rating is up to IP65, can be used in different environment. Use
aluminum alloy and PC as the material which ensures that it can work stably in different environment.
Life Span: 50,000 Hours.
Application:
The lamp can be used for outdoor hallway, factory,
basement, warehouse, parking lot...
RoHS
COMPLIANT
warranty 3 years
Dimensions(Unit:mm):
Specification:
Model Number
FTN-TP-070-W
Color
White
LED Type Light Output Beam Angle
(degrees)
/ Quantity
(lumen)
SMD 3528
FTN-TP-070-NW Natural white LED
(756PCS)
FTN-TP-070-WW warm white
www.signcomplex.com
CCT
CRI
5260
230
5500-7000K
80
5560
230
4000K-4500K
80
4460
230
2700-3200K
82
Max.Current Power
(W)
(Amps)
0.91
70
Voltage
PF
AC 100-240V
≥0.9
50/60Hz
Net Weight Gross Weight
2. 7
Tel:+86-755-27608650
Fax:+86-755-27608651
[email protected]
Yijia Industrial Park, Fuqian Road, Guanlan Town, Baoan, Shenzhen, Guangdong, China
2 . 95
P1
Signcomplex
we bring innovation and give impression
Structure diagram:
Waterproof adapter
Heat sink (Aluminum alloy 6063)
Screw (stainless steel)
Mounting bracket (Aluminum alloy 5052)
Batten (Aluminum alloy 6063)
Cover (PC)
Sealing strip (silicone)
End cap (ADC12)
Screw (stainless steel)
Sealing sheet (silicone)
Installation information:
1.First set up accessories and fittings of the light.
2.Cut off the power before installation.
3.Make sure the product is fixed tightly to the installation surface(install it according
to diagram as below).
4.Connect the wire of the light to the power supply, then switch on the power.
Intallation Method I
Size:(mm)
55mm
1180.5mm
screw
1. Drill 4 holes of 8mm diameter.
2. Install the holder on the wall,
be attention that the direction
should be the same.
3. Turning the screw but not tightly,
leave 3-4mm space.
4. Install the light and tighten the screw.
Intallation Method II
Size:(mm)
1204
Screw
2. Install the clip onto the wall.
1.Drill 4 holes of 6.5mm.
3. Use screws to conenct the hanging
ring with screw holes on both sides of
the lamp.
4. Adjust the height of the wires of both
sides.
Other Cautions:
1.This product must be installed by professional personnels.
2.Use environment: -20℃ to 45℃.
3.If there is any damage on the power line or the shell of the product, it should be taken
as defective product and do not use it.
4.Dangerous high voltage, non-professionals are not allowed to maintain the product.
www.signcomplex.com
Tel:+86-755-27608650
Fax:+86-755-27608651
[email protected]
Yijia Industrial Park, Fuqian Road, Guanlan Town, Baoan, Shenzhen, Guangdong, China
P2