yasnac j300 memory upgrade installation manual

YASNAC J300 MEMORY UPGRADE
INSTALLATION MANUAL
Nexas Networks Inc.
627 Main Street East, Suite L09
Hamilton, Ontario, Canada L8M 1J5
Phone: 905-581-3717 Fax: 877-293-7105
Email: [email protected]
www.nexanet.com
© 2014 Nexas Networks Inc. All Rights Reserved. Web Version.
Yasnac is a trademark of Yaskawa Ltd. All other brand names and models mentioned in this manual are for reference only and are
considered to be trademarks or registered trademarks of their respective owners.
Nexas Networks Inc. assumes no liability for the use of this manual.
File: ISO9000/DOCS/M100722B - Nexas J300 Memory Upgrade - 2 Meg JMM01-2 - web.doc
INTRODUCTION
CHAPTER 1: INTRODUCTION
The Yasnac J300 CNC has two distinct part program memory areas – a base
memory or about 256k on the JMM01-01 base board and we provide a
JMM01-02 for the JCP01 board to enable 2 Megabytes (or 5120 Meters of
tape equivalent) of part program storage – the maximum for the J300.
The available Yasnac J300 memory options are as follows:
BOARD
MEMORY
OPTION (web version)
JMM01-01
JMM01-01
JMM01-01
JMM01-01
JMM01-02
JMM01-02
JMM01-02
JMM01-02
40M or 16k (standard)
80M or 32k
160M or 64k
320M or 128k
640M or 256k
1280M or 512k
2560M or 1 Megabyte
5120M or 2 Megabyte
OPMxx = xxxx
OPMxx = xxxx
OPMxx = xxxx
OPMxx = xxxx
OPMxx = xxxx
OPMxx = xxxx
OPMxx = xxxx
OPMxx = xxxx xxxx = x
Where x” is original value to be added into the ASCII (e.g. 01000111 = 71 or
64+4+2+1 = 71 when the ASCII Columns are D7= 128, D6= 64, D5= 32, D4=
16, D3= 8, D2= 4, D1= 2 & D0= 1).
Note the JMM01-01 and 02 have 1 Meg of FROM (Flash Memory for the user
LADDER and C-APL files) specific to each machine.
A Yasnac J300 Controller JCP01 with a JMM01-02 Additional Memory and PCMCIA Flash Backup Card
©Copyright 2014 Nexas Networks Inc. All rights reserved.
No part may be used or copied without the express written consent of Nexas Networks Inc.
Nexas Networks Inc. assumes no liability for the use of this information.
.
J300 MEMORY INSTALLATION
CHAPTER 2: INSTALLATION OVERVIEW
Before starting the installation, power on the control and verify that the
machine tool is in good working order. If the control has a system error
during or after your installation, you will appreciate a backup.
The Yasnac JMM01-02 board contains part programs above those stored
in the main JCP01 board. The JMM01-02 therefore is an additional part
program storage above 160M (64kB) and it can also contain macro
programs for tool changers that are protected from download.
An install of the JMM01-02 board will erase all part programs in both the
JCP01 and the JMM01-02 boards during the REGEN (regenerate) process,
so a complete backup of part program & macro files is necessary. That
said, a full backup is recommended anyway on the supplied PCMCAIA
Flash Memory Card.
Please note that only certain Flash cards below 20 Megabytes will work
for the special ladder reloading maintenance mode we need at one point
of the installation. The Yasnac J300 will work with larger ATA Type 1
Flash Cards, but just not in this mode.
If in doubt, consult your Yasnac manuals, as they are your ultimate
authority on your particular version of control.
J300 RS-232C Serial Specification:
Port 1 = CN02 on the JCP01 Board – PCR 20 Pin High Density Connector – Wire Connecting is labelled C222
Port 2 = CN02 on Operation MDI Panel – fed via CN01 (PANEL) from JCP01 Board
©Copyright 2014 Nexas Networks Inc. All rights reserved.
No part may be used or copied without the express written consent of Nexas Networks Inc.
Nexas Networks Inc. assumes no liability for the use of this information.
.
J300 MEMORY INSTALLATION
A Yasnac J300 Mill CRT & MDI Interface. Note the WR (INPUT) key is on the bottom right.
©Copyright 2014 Nexas Networks Inc. All rights reserved.
No part may be used or copied without the express written consent of Nexas Networks Inc.
Nexas Networks Inc. assumes no liability for the use of this information.
.
J300 MEMORY INSTALLATION
YASNAC J300 MEMORY INSTALLATION
Time Needed:
Tools Needed:
Components:
Control:
About 2 hours
1 x Philips #1 Screwdriver to Remove Cables
1 x JMM01-2 memory board
1 x Set of Instructions
Yasnac J300 Mill or Lathe CNC
Before starting the installation, power on the control and verify that the
machine tool is in good working order. Also make sure that you have a
card reader for a PCMCIA Type I flash card on an old laptop or USB card
reader if you want to back up the settings and files to a computer. You can
install using the card and not save back to a computer, but we advise
otherwise.
Important!
1. Download and save the original programs. Parameters, settings, offsets,
etc – after setting the serial port to PCCARD and use the card supplied
mounted on the JCP01 board
a. Power off the NC control. Turn the system switch (the “ball”)
on the JCP01 board to “2” – like a parameter write enable
power on setting;
b. Insert supplied PCMCIA Flash Card in the upper JCP01 slot;
c. Power on the machine and go to P4 MAIN, then hit soft key
IN/OUT, to see the serial settings – write them down;
PCMCIA
Card Setup
d. Then cursor over to the UNIT line and highlight “RS232” in the
upper window and hit the PCCARD soft key to select the card
for both inputting and outputting;
©Copyright 2014 Nexas Networks Inc. All rights reserved.
No part may be used or copied without the express written consent of Nexas Networks Inc.
Nexas Networks Inc. assumes no liability for the use of this information.
.