Korenix JetNet 4000 Series Industrial Ethernet Rail Switch User`s

Transcription

Korenix JetNet 4000 Series Industrial Ethernet Rail Switch User`s
Korenix JetNet 4000 Series
Industrial Ethernet Rail Switch
User’s Manual
First Edition, April 2005
www.korenix.com
Korenix JetNet 4000 Series
Industrial Ethernet Rail Switch
User’s Manual
Copyright Notice
Copyright © 2005 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction in any form or by any means without permission is prohibited.
Table of Contents
Chapter 1
Introduction .............................................................................................1-1
Overview........................................................................................................... 1-2
Ethernet Switching Technology ........................................................................ 1-2
Product Features .............................................................................................. 1-2
Package Checklist ............................................................................................ 1-3
Chapter 2
Hardware Installation ..............................................................................2-1
Introduction....................................................................................................... 2-2
Panel Layout ....................................................................................................... 2-2
Reset Button ....................................................................................................... 2-2
LED Indicators..................................................................................................... 2-2
DIP Switch........................................................................................................... 2-4
Wiring the Power Inputs ................................................................................... 2-4
Wiring the Relay Output ................................................................................... 2-4
Wiring the Ethernet Ports ................................................................................. 2-5
Wiring the Fiber Ports ....................................................................................... 2-6
DIN-Rail Mounting Installation .......................................................................... 2-6
Wall-Mounting Installation................................................................................. 2-7
Chapter 3
Web-based Management ........................................................................3-1
Introduction....................................................................................................... 3-2
Preparation for Web Management.................................................................... 3-2
System Login.................................................................................................... 3-2
Start Using Web-based Management Interface to Configure ........................... 3-3
Menu Bar Introduction......................................................................................... 3-3
Configuring Your JetNet 4000 ............................................................................. 3-4
Chapter 4
Troubleshooting ......................................................................................4-1
Incorrect Connections....................................................................................... 4-2
Faulty or Loosen Cables ..................................................................................... 4-2
Non-standard Cables .......................................................................................... 4-2
Improper Network Technologies ......................................................................... 4-2
LED Indicators .................................................................................................. 4-2
Appendix A
Specifications......................................................................................... A-1
1
Chapter 1
Introduction
Welcome to Korenix JetNet 4000 Series Industrial Ethernet Rail Switch. JetNet 4000 Series is a
web-managed rail switch that is specially designed for industrial applications.
The following topics are covered in this chapter:
Overview
Ethernet Switching Technology
Product Features
Package Checklist
Installation Guide
Overview
JetNet 4000 Series is a web-managed rail switch that is specially designed for industrial
applications. JetNet 4000 uses one-piece formed aluminum case that complies with IP31
industrial standard, allowing JetNet 4000 to operate under harsh industrial environments. JetNet
4000 provides dual DC power inputs, ensuring your systems to run non-stop. JetNet 4000 also
supports Super Ring technology, which can offer you industrial-grade redundant network
solution. When your primary path fails, the entire system can still function normally with the
secondary path activated. JetNet 4000 supports fiber connectors, effectively extending switches’
transmission distance. Web-based management interface ensures easy management by using
web browser over the network.
Ethernet Switching Technology
Ethernet Switching Technology dramatically boosted the total bandwidth of a network, eliminated
congestion problems inherent with CSMA/CD (Carrier Sense multiple access with Collision
Detection) protocol, and greatly reduced unnecessary transmissions.
This revolutionized networking. First, by allowing two-way, simultaneous transmissions over the
same port (Full-duplex), which essentially doubled the bandwidth. Second, by reducing the
collision domain to a single switch-port, which eliminated the need for carrier sensing. Third, by
using the store-and-forward technology’s approach of inspecting each packet to intercept corrupt
or redundant data, switching eliminated unnecessary transmission that slow the network. By
employing address learning, which replaced the inefficient receiving port.
Auto-negotiation regulates the speed and duplex of each port, based on the capability of both
devices. Flow-control allows transmission from a 100Mbps node to a 10Mbps node without loss
of data. Auto-negotiation and flow-control may require disablement for some networking
operations involves legacy equipment. Disabling the auto-negotiation is accomplished by fixing
the speed or duplex of a port.
Ethernet Switching Technology supplied higher performance at costs lower than other solutions.
Wider bandwidth, no congestion, and the reduction in traffic is why switching is replacing
expensive routers and inefficient hubs as the ultimate networking solution. Switching brought a
whole new way of thinking to networking.
Product Features
Korenix JetNet 4000 Series products have the following features:
Redundant Ethernet Super Ring
Supports VLAN/QoS/IGMP Snooping
Web-based Configuration
Redundant DC Power Inputs
Alarm Relay Output
Robust Aluminum case, IP31 standard
DIN-Rail/Wall-mounting/Desktop Installation
5/8 10/100TX ports for JetNet 4005/4008
4/6 10/100TX ports and 1/2 100FX port(s) for JetNet 4005f/4008f
Conforms to IEEE 802.3 10Base-T, 802.3u 100Base-TX/100Base-FX
RJ-45 ports support auto MDI/MDI-X function
Store-and-Forward switching architecture
1-2
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Introduction
Web management GUI
Provides Fiber link ability
IEEE 802.3x flow control supported
¾
Flow control on full-duplex mode
¾
Back pressure on half-duplex mode
Supports Class of Service
Supports IGMP with Query mode for multi media application
Supports broadcast packet filtering
Supports SNTP
Provides reverse polarity protection
1Mbits embedded memory
2K MAC address table
Supports port-based VLAN / 802.1 Q Tag VLAN
Package Checklist
Korenix JetNet 4000 Series products are shipped with the following items:
1 Korenix Industrial Web-Managed Ethernet Rail Switch
One DIN-Rail clip (attached with the JetNet switch)
One wall mounting plate and six screws
Documentation and Software CD
Quick Installation Guide
If any of the above items is missing or damaged, please contact your local sales representative.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
1-3
2
Chapter 2
Hardware Installation
This chapter includes information of installation and configuration.
The following topics are covered in this chapter:
Introduction
¾
Panel Layout
¾
Reset Button
¾
LED Indicators
¾
DIP Switch
Wiring the Power Inputs
Wiring the Relay Output
Wiring the Ethernet Ports
Wiring the Fiber Ports
DIN-Rail Mounting Installation
Wall-Mounting Installation
Introduction
Panel Layout
Here we use JetNet 4008f as an example.
Front View
1 LED indicators
2 DIP switch
3 RJ-45 ports
4 Fiber ports
Bottom View
The bottom view of the JetNet 4000
Series Industrial Web-Managed
Ethernet Rail Switch consists of one
terminal block connector with two DC
power inputs and one DC IN power
jack for an additional AC/DC power
adapter.
Reset Button
The Reset button provides users with a quick and easy way to restart JetNets and restore the
default settings.
To restart: press the Reset button for 2 seconds and release.
To restore the default settings: press the button for 5 seconds and release.
LED Indicators
There are 7 diagnostic LEDs and 8 Port LEDs located on the front panel of JetNet 4005, while
there are 9 diagnostic LEDs and 12 Port LEDs on JetNet 4008. Industrial Ethernet Rail Switch.
These LED indicators provide administrators with real-time system status. Table 1 gives
descriptions of the function of each LED indicator.
2-2
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Hardware Installation
LED
Status
Description
Green
Power is on.
Off
No power is being supplied.
Green
Power is on.
Off
No power is being supplied.
Green
Power is on.
Off
No power is being supplied.
Green
Indicates that this JetNet is the master of the
Super Ring.
Off
Indicates that this JetNet is NOT the master of
the Super Ring.
Yellow
Power, or UTP port, or fiber port failure occurs.
Off
No power, or UTP port, or fiber port failure
occurs.
Status
Description
Green
A network device is detected.
Blinks
The port is transmitting or receiving packets from
the TX device.
Off
No device is attached.
Orange
The port is operating in full-duplex mode.
FDX/COL of Port 7
(JetNet 4008f)
Blinks
Collision of packets occurs.
Off
The port is in half-duplex mode or no device is
attached.
LNK/ACT of Port 5
(JetNet 4005f)
Green
A network device is detected.
Blinks
The port is transmitting or receiving packets from
the TX device.
Off
No device is attached.
Orange
The port is operating in full-duplex mode.
Blinks
Collision of packets occurs.
Off
The port is in half-duplex mode or no device is
attached.
Orange
The port is operating in full-duplex mode.
Blinking
orange
Collision of Packets occurs.
Off
The port is in half-duplex mode or no device is
attached.
Green
A network device is detected.
Blinking
green
The port is transmitting or receiving packets from
the TX device.
Off
No device is attached.
PWR
PWR 1
PWR 2
R.M
Fault
Port LED
LNK/ACT of Port 7
(JetNet 4008f)
LNK/ACT of Port 8
(JetNet 4008f)
FDX/COL of Port 5
(JetNet 4005f)
FDX/COL of Port 8
(JetNet 4008f)
Port Status
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
2-3
DIP Switch
The DIP switch is used to configure which JetNet in a Super Ring to be a master switch.
DIP SWITCH
Status
R.M.
P1 to P8 (JetNet 4008f)
P1 to P5 (JetNet 4005f)
Description
ON
Set this switch to be the Ring Master.
Off
Set this switch NOT to be the Ring Master.
ON
To enable port break alarm on each port.
Off
To disable port break alarm.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent the DC wires from being loosened.
Note: The suitable electric wire ranges from 12 to 24 AWG.
Note: The additional power jack is designed for office use.
Wiring the Relay Output
The relay output alarm contacts are in the middle of the terminal block connector as shown in the
figure below. By inserting the wires and set the DIP switch to “ON”, relay output alarm will detect
any power or port failures, and form an open circuit. The figure below illustrates an example of
how relay output alarm works.
Note: The connection point of alarm relay output only switches on and off the circuit. It does not
supply any power. The connection point can only bear 1A@DC24V.
Fault Alarm Contact
The open circuit will form when the
power failure or port link failure.
24V DC Buzzer
24V Battery
The fault alarm device will send a
warning signal to warn the user, ex:
alarm sound or flash light.
2-4
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Hardware Installation
1. Insert the alarm device’s negative wire into assigned position of the terminal block connector.
2. Tighten the wire-clamp screws to prevent the wires from being loosened.
Wiring the Ethernet Ports
RJ-45 ports with auto MDI-MDI-X function: JetNet 4008 has eight 10/100 Mbps auto-sensing
ports for 10Base-T or 100Base-TX device connection. The UTP ports will auto-detect 10Base-T
and 100Base-TX connections. Auto MDI/MDI-X function allows users to connect another switch
or workstation without changing straight-through or cross-over cabling. See the figures below for
the schematic diagram of straight-through and cross-over cabling.
Straight-through Cabling Schematic
Cross-over Cabling Schematic
Use four twisted-pair Category 5 cables for RJ-45 port connection. Connect one side of an
Ethernet cable into the JetNet’s TX port, while the other side is connected to the attached device.
The LED will light up when the cable is correctly connected. Refer to the LED Indicators section
for descriptions of the function of each LED indicators. The cables between the JetNet and the
attached device (e.g. switch, hub, or workstation) must be less than 100 meters (328 ft.).
All ports of JetNet 4000 support auto-MDI/MDI-X function. When you use an Ethernet cable to
connect other devices, such as computers, switches or hubs, pin 1, 2, 3, and 6 of the 8-pin RJ45
connector are used to communicate with the connected devices. Pin1, 2, 3, and 6’s signals are
converted by the MDI-X function, as shown in the table below.
Pin MDI-X
Signals
MDI Signals
1
RD+
TD+
2
RD-
TD-
3
TD+
RD+
6
TD-
RD-
Two switches are now up-linked together. If we change the up-link port manually at this time,
MAC address table will change as well. After MAC address table makes the changes, and then
the data can be transmitted between these two switches. This period of time is called MAC
address table aging time. Korenix JetNet 4000’s default aging time is 5 minutes, which means
that if you manually change the up-link port, you will need to wait for 5 minutes before the data
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
2-5
can be sent. If the aging time is too short, MAC address table will constantly refresh, resulting in
large consumption of the switch’s computing resources. For this reason, longer aging time is
recommended.
Wiring the Fiber Ports
To connect the fiber port on your JetNet 4005f or JetNet 4008f to another one located on another
JetNet, follow the figure below. Wrong connection will cause fiber ports not to work normally.
JetNet fiber models have two 100Base-FX ports with SC type connectors.
Fiber segment using single mode must use 8/125 or 9/125 um single-mode fiber cables. For
single mode, the connection distance can be up to 30 km.
Fiber segment using multi mode must use 50 or 62.5/125 um multi-mode fiber cables. For single
mode, the connection distance can be up to 2 km.
DIN-Rail Mounting Installation
The DIN-Rail clip is already attached to the JetNet 4000 Series products when packaged. If the
DIN-Rail clip is not screwed on the JetNet, follow the instructions and the figure below to attach
the DIN-Rail clip to the JetNet. Here we use JetNet 4008 as an example.
1. Use the screws to attach the DIN-Rail clip to the rear panel of the JetNet 4008.
2. To remove the DIN-Rail clip, reverse step 1.
Follow the steps below to mount the JetNet to the DIN-Rail track.
1. First, insert the upper end of the DIN-Rail clip into the back of the DIN-Rail track from its
upper side.
2-6
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Hardware Installation
2. Lightly push the bottom of the DIN-Rail clip into the track.
3. Check if the DIN-Rail clip is tightly attached on the track.
4. To remove the JetNet from the track, reverse the steps above.
Wall-Mounting Installation
Follow the steps below to install the JetNet 4008f with the wall mounting plate.
1. To remove the DIN-Rail clip from the JetNet 4008f, loosen the screws from the DIN-Rail clip.
2. Place the wall mounting plate on the rear panel of the JetNet 4008f.
3. Use the screws to tighten the wall mounting plate onto the JetNet 4008f.
4. Use the hook holes at the corners of the wall mounting plate to hang the JetNet 4008f onto
the wall.
5. To remove the wall mounting plate, reverse the steps above.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
2-7
2-8
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
3
Chapter 3
Web-based Management
This chapter includes information about how to configure and manage your JetNet via
web-based interface.
The following topics are covered in this chapter:
Introduction
Preparation for Web Management
System Login
Start Using Web-based Management Interface to Configure
¾
Menu Bar Introduction
¾
Configuring Your JetNet 4000
Introduction
An embedded HTML website is placed in the flash memory inside the CPU board of the JetNet.
This HTML website allows users to use a web-based management interface to configure JetNets
from anywhere on the network via a standard browser, such as Microsoft Internet Explorer.
The web-based management interface supports Internet Explorer 5.0. It is based on Java
Applets with aiming to reduce network bandwidth consumption, to enhance the access speed,
and to offer an easy-to-use management screen.
Note: IE 5.0 or any later version does not allow Java Applets to open sockets by default. Users
have to directly modify the browser settings to enable Java Applets to use network ports.
Preparation for Web Management
Before you start to use Web-based management interface to manage JetNets, make sure that
JetNets are properly installed on your network, and every PC on this network can check JetNets
via the web browser. Here we use JetNet 4008f as an example.
1. Make sure your network card is working normally, and your operating system supports
TCP/IP protocol.
2. Wire the JetNet’s DC power input and connect your computer to the JetNet.
3. Make sure that the JetNet’s default IP address is 192.168.10.1.
4. Change your computer’s IP address to 192.168.10.2.
5. Switch to DOS command mode, and ping 192.168.10.1 to make sure that the respond time
is normal.
System Login
1. Launch the Internet Explorer on the PC.
2. Type http:// and the IP address of the JetNet. And then press Enter.
3. The login screen will appear next.
4. Key in the user name and the password. The default user name and the password is admin.
3-2
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
5. Click on Enter or OK, and then the homepage of the web-based management interface will
appear.
6. Once you enter the web-based management interface, change the JetNet’s IP address to fit
your network environment.
Start Using Web-based Management Interface to Configure
Menu Bar Introduction
Home
Port Status
Port
Statistics
IP Security
Port Control
IP
SNTP
RSTP
Configuration
Security
Configuration TFTP Update Factory
Manager
Backup
Firmware
Default
Switch
Settings
Super Ring
Port Mirroring VLAN
Configuration
QoS
IGMP
Save
System
Configuration Reboot
Rate Control
Home
The homepage of the web-based management interface.
Port Status
This section is to display the port status and settings.
Port Statistics
This section is to display the JetNet’s port data flow statistics.
Port Control
This section is to configure the JetNet’s port settings.
Switch Settings
This section is to display the information of the JetNet’s system.
Port Mirroring
This section is to enable and configure port mirroring settings.
VLAN Configuration
This section is to enable and configure VLAN settings.
IP Configuration
This section is to set up the JetNet’s IP address.
SNTP
This section is to enable the network time server.
IP Security
This section is to set up the IP address which allows users to access the JetNet from the web.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
3-3
RSTP
This section is to enable and configure the RSTP function.
Super Ring
This section is to enable and configure Super Ring settings.
QoS
This section is to enable and configure QoS(Quality of service) settings.
IGMP
This section is to enable and configure the JetNet’s IGMP Snooping function.
Security Manager
This section is to change the username and the password.
Configuration Backup
This section is to backup the JetNet’s settings to a file on your PC.
TFTP Update Firmware
This section is to use TFTP utility to update the latest firmware to the JetNet.
Factory Default
This section is to restore the factory default settings.
Save Configuration
This section is to save the JetNet’s settings.
System Reboot
This section is to reboot the JetNet.
Rate Control
Set up every port’s bandwidth rate and packet limitation type.
Configuring Your JetNet 4000
Port Status
In this window, you can see every port’s status.
Port: indicates the port number.
Type: indicates the speed mode of the port. For example, 100TX means 100 Mbps.
Link: Down indicates that connection is not established, while Up indicates that the connection
is successfully established.
State: indicates whether this port is Enabled or Disabled. Disconnection will be seen as
Disabled.
Negotiation: Auto means that the JetNet will auto-negotiate the speed (10 or 100 Mbps) of the
remote device, and the transmission mode (full or half duplex). Force means that the JetNet runs
according to your settings.
3-4
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
Speed Duplex: indicates the port speed. Config column shows the configuration set up by users.
The Actual column shows the actual speed of the port.
Flow Control: Config column shows the configuration set up by users. Actual column shows
the actual status of the port.
Single Port Status
You can directly click on any port on the panel display on the left side to see its information.
Port Statistics
In this section, you can see all kinds of statistics of each port. Click on Clear to remove any
counts.
Port Control
You can change the port settings here.
Select the port you want to configure. You will see the current settings and status of the selected
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
3-5
port.
In State column, you can enable or disable the control over this port.
In Negotiation column, you can configure the auto negotiation mode to Auto, Nway (to specify
the speed/duplex on this port and enable auto-negotiation), or Force.
In Speed column, you can configure the speed of this port.
In Duplex column, you can configure the full-duplex or half-duplex mode of this port.
In Flow Control column, you can enable or disable the Flow Control function by selecting ON or
OFF for the Full Duplex mode.
Once you finish configuring the settings, click on Apply to save the configuration.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
Switch Settings
You can assign the system name, location, and view the system information.
System Name: you can assign a name to the JetNet.
System Location: you can specify the JetNet’s physical location here.
System Description: you can briefly describe the JetNet you are using.
Firmware Version: this information shows the firmware version on this JetNet.
Kernel Version: this information shows the kernel version on this JetNet.
Hardware Version: this information shows the hardware version of this JetNet.
MAC Address: this information displays the unique hardware address assigned by the
manufacturer (the default setting).
Once you finish configuring the settings, click on Apply to save the configuration.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
3-6
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
Port Mirroring
The Port mirroring is a method for you to monitor traffic in switched networks. Traffic through
ports can be monitored by one specific port. That is, traffic goes in or out of the monitored ports
will be duplicated into mirror ports.
Port Mirroring State: you can set mirroring mode, including Disable, RX, TX, and Both.
Analysis Port: It means that the mirror ports can be used to see the traffic of all monitored ports.
you can connect mirror ports to a LAN analyzer or Netxray.
Monitor Port: these are the ports you want to monitor. The traffic of all monitored ports will be
copied to mirror ports. You can select up to 25 monitor ports in the switch. You can choose which
port you want to monitor in only one mirror mode.
Once you finish configuring the settings, click on Apply to save the configuration.
Note: If you want to disable this function, select the monitor port to none.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
VLAN Configuration
A Virtual LAN (VLAN) is a logical network that limits the broadcast domain. It allows you to
isolate network traffic so that only members of the VLAN would receive traffic from the same
VLAN members. Basically, creating a VLAN from a switch is logically equivalent of reconnecting
a group of network devices to another Layer 2 switch. However, all the network devices are still
plugged into the same switch physically.
JetNet 4000 Series supports port-based and 802.1Q (tagged-based) VLAN. The VLAN mode is
“disable” by default.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
3-7
Port-based VLAN
Packets only go to the members of the same VLAN groups. Note that all of the unselected ports
are treated as belonging to another single VLAN. If the port-based VLAN enabled, the
VLAN-tagging will be ignored.
1. Click on Add to add a new VLAN group.
2. Enter the VLAN name, group IP, and then select the members for this VLAN group.
3. Click on Apply to adopt the settings.
4. Next you will see the VLAN group be displayed.
5. If the groups list is longer than one page, you can click on Next Page to view other VLAN
groups.
6. Use Delete button to delete unwanted VLANs.
7. Use Edit button to modify the existing VLANs.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise
the settings you made will be gone when the JetNet is powered off.
3-8
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
802.1Q VLAN
Tag-based VLAN is an IEEE 802.1Q standard. Therefore, it is possible to create a VLAN across
different switches. IEEE 802.1Q Frame Tagging technology will insert a “tag” into the Ethernet
frames. The tag contains a VLAN Identifier (VID) that indicates which VLAN this frame belongs to.
Since the switch only has to check the frame’s tag without the need to go through the content of
the frame, it saves a lot of a switch’s computing resources.
Basic
1. Click on Add button to add a new VLAN.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
3-9
2. Group Name: you can assign a name for the new VLAN here.
3. VLAN ID: you can type in VLAN ID here (the value is between 2 to 4094). The default value
is 1.
4. Select ports from the available ports box, click on Add to add to the JetNet, and then click on
Next to continue.
5. Here you can set the outgoing frames to be VLAN-Tagged frames or untagged, and click on
Apply to save the settings.
Tag: indicates that outgoing frames are VLAN-Tagged.
Untag: indicates that outgoing frames are not VLAN-Tagged.
Port VID
Port VLAN ID: you can enter the port VLAN ID here.
To reset to the default values, click on Default.
Once you finish configuring the settings, click on Apply to save the configuration.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
3-10 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
How To Set Up a 802.1q VLAN?
Switch 1
Switch 2
Here is an example. We would like to use Port 2s and Port 3s of Switch 1 and Switch 2 to form
VLAN 1, and Port 4s and Port 5s to form VLAN 2. VLAN 1 and 2 cannot communicate with each
other. The VLAN settings for Switch 1 are as follows (settings for Switch 2 are the same with
Switch 1):
Setting 1: Configure Port 1/2/3/4/5’s VLAN ID to 2, Untag, and Port 1’s PVID to 2.
Setting 2: Configure Port 1/2/3’s VLAN ID to 3, Port 8 with Tag, and Port 2/3’s PVID to 3.
Setting 3: Configure Port 1/4/5’s VLAN ID to 4, Port 8 with Tag, and Port 4/5’s PVID to 4.
Here we use Setting 1 as an example to show the detailed configuration steps”
1. Set Port 1/2/3/4/5 to be a VLAN group, configure VLAN ID to 2, and click on Next to
continue.
2. Configure all 5 ports with Untag, and then click on Apply to apply your configuration.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-11
3. Click on Port VLAN ID tag to enter the configuration window. Select
Port 1, and enter 2 for its Port VLAN ID.
Follow the steps for Setting 1 to configure Setting 2 and 3.
Note: JetNet uses Port VLAN ID to identify the VLAN inside the JetNet, and VLAN ID to identify
the VLAN across different JetNets. Therefore, you need to be aware of the differences between
Port VLAN ID and VLAN ID in 802.1q VLAN (Tag VLAN) settings.
IP Configuration
This function allows users to configure the JetNet’s IP settings.
DHCP Client: You can Enable or Disable the DHCP Client function. When the DHCP Client
function is enabled, an IP address will be assigned to the JetNet from the network DHCP server.
The default IP address will therefore be replaced by the one assigned by the DHCP server.
IP Address: you can assign the IP address that your network is using to the JetNet. If the DHCP
Client function is enabled, you don’t need to assign an IP address to the JetNet. The IP address
assigned by the DHCP server will be shown here. The default IP is 192.168.10.1.
Subnet Mask: you can assign the subnet mask for the IP address here. If the DHCP Client
function is enabled, you don’t need to assign the subnet mask.
Gateway: You can assign the gateway for the JetNet here. The default gateway is
192.168.10.254.
Once you finish configuring the settings, click on Apply to save the configuration.
3-12 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
SNTP
You can configure SNTP (Simple Network Time Protocol) settings here. The SNTP function
allows you to synchronize clocks of several JetNets on the network.
SNTP Client: you can acquire the current time from the SNTP server by enabling or disabling the
SNTP function.
UTC Time-zone: you can configure the time zone where the JetNet is located. The following
table lists the time zones for different locations for your reference.
Local Time Zone
Conversion from UTC
Time at 12:00 UTC
ADT - Atlantic Daylight
-3 hours
9 am
AST - Atlantic Standard
EDT - Eastern Daylight
-4 hours
8 am
EST - Eastern Standard
CDT - Central Daylight
-5 hours
7 am
CST - Central Standard
MDT - Mountain Daylight
-6 hours
6 am
MST - Mountain Standard
PDT - Pacific Daylight
-7 hours
5 am
PST - Pacific Standard
ADT - Alaskan Daylight
-8 hours
4 am
ALA - Alaskan Standard
-9 hours
3 am
HAW - Hawaiian Standard
-10 hours
2 am
Nome, Alaska
-11 hours
1 am
CET - Central European
FWT - French Winter
MET - Middle European
MEWT - Middle European
Winter
SWT - Swedish Winter
+1 hour
1 pm
EET - Eastern European, USSR
Zone 1
+2 hours
2 pm
BT - Baghdad, USSR Zone 2
+3 hours
3 pm
ZP4 - USSR Zone 3
+4 hours
4 pm
ZP5 - USSR Zone 4
+5 hours
5 pm
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-13
ZP6 - USSR Zone 5
+6 hours
6 pm
WAST - West Australian
Standard
+7 hours
7 pm
CCT - China Coast, USSR Zone
7
+8 hours
8 pm
JST - Japan Standard, USSR
Zone 8
+9 hours
9 pm
EAST - East Australian
Standard GST
Guam Standard, USSR Zone 9
+10 hours
10 pm
IDLE - International Date Line
NZST - New Zealand Standard
NZT - New Zealand
+12 hours
Midnight
SNTP Server IP: you can set up the IP address of the SNTP server.
Switch Timer: the current time on the JetNet net will be shown here.
Once you finish configuring the settings, click on Apply to save the configuration.
IP Security
In IP Security section, you can set up 4 specific IP addresses which have the authorization to
access the JetNet via the web browser.
Enable IP Security: check this option to enable the IP security function.
Security IP 1 to 4: you can assign up to 4 specific IP addresses. Only these 4 IP addresses can
access and manage the JetNet via the web browser.
Once you finish configuring the settings, click on Apply to save the configuration.
RSTP
3-14 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
The Spanning Tree Protocol (STP) is a standardized method (IEEE 802.1d) for avoiding loops in
networks connected with switches. The Rapid Spanning Tree Protocol (RSTP) is the evolution of
the Spanning Tree Protocol, and provides faster spanning tree convergence after a topology
change. JetNets support both STP and RSTP.
System Configuration
Under System Configuration, you can see Root Bridge Information. You also can change
Spanning Tree settings here.
RSTP Mode: you must enable STP or RSTP function before configuring any related parameters.
The settings of the STP- or RSTP-related parameters are the same. 802.1d = STP mode.
802.1w = RSTP mode.
Priority (0-61440): this value is used to identify the root bridge. The bridge with the lowest value
has the highest priority, and is selected as the root. If you change the value, you must reboot the
JetNet to assign a path priority number. The value must be multiples of 4096 according to
standard rule of the protocol.
Max Age (6-40): this value is the number of seconds that a bridge waits without receiving
Spanning Tree Protocol configuration messages before attempting a reconfiguration. Enter a
value between 6 and 40.
Hello Time (1-10): this value is the time which controls the JetNet to send out the BPDU packet
to check STP current status. Enter a value between 1 and 10.
Forward Delay Time (4-30): this value is the number of seconds that a port waits before
changing its Spanning Tree Protocol learning and listening states to the forwarding state. Enter a
value between 4 and 30.
Once you finish configuring the settings, click on Apply to save the configuration.
Note: You must follow the rule set below to configure the Max Age, Hello Time, and Forward
Delay Time.
2 × (Forward Delay Time value-1)≧Max Age value≧2×(Hello Time value+1)
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-15
Per Port Configuration
Select the port you want to configure. You will see the current settings and status of the selected
port.
Path Cost: this value is the cost of the path to the other bridge from this transmitting bridge at the
specified port. Enter a number between 1 and 200000000.
Priority: this is the value that decides which port should be blocked by priority in LAN. Enter a
value between 0 and 240. The value of priority must be multiples of 16.
Admin P2P: some of the rapid state transactions that are possible within RSTP depend upon
whether the port concerned can only be connected to only on other bridge (i.e. it is served by a
point-to-point LAN segment), or can be connected to two or more bridges (i.e. it is served by a
shared medium LAN segment). This function allows the P2P status of the link to be manipulated
administratively. True means P2P is enabled. False means P2P is disabled.
Admin Edge: the port directly connected to end stations cannot create a bridging loop in the
network. To configure the port as an edge port, set the port to True status.
Admin Non Stp: the status shown here indicates whether this port includes the STP mathematic
calculation. True means that this port does not include STP mathematic calculation. False
means that this port includes the STP mathematic calculation.
Once you finish configuring the settings, click on Apply to save the configuration.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
Super Ring
Super Ring technology provides a faster redundant recovery than Spanning Tree topology does.
How Super Ring works is similar to STP or RSTP, but the algorithm is not exactly the same.
In a Super Ring topology, every JetNet should enable the Super Ring function, and assign 2
member ports in this ring. Only one JetNet in the Super Ring group would be set as a backup
switch, and one of its 2 member ports would be blocked, which is called the backup port. The
other port is called the working port. Other JetNets are called working switches, and their 2
member ports are also called working ports. When the network connection fails, the backup port
will automatically become a working port to recover the failure
You can use the DIP switches to configure one of the JetNets to be the ring master or slave. The
ring master has the rights to negotiate and place commands to other JetNets in the Super Ring
group. If there are 2 or more JetNets set to be the ring master, then the software will select the
3-16 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
one with the lowest MAC address number to be the ring master. When the JetNet is set to be the
ring master, the Super Ring configuration interface will display the message indicating that this
JetNet is the ring master.
The system also supports the coupling ring function which allows 2 or more Super Ring groups
to be connected together to provide the redundant backup solution.
Enable Super Ring: you can enable the Super Ring function by checking this option.
Note: You must enable the Super Ring function before connecting any backup path.
Working Ports: you can assign 2 ports as the member ports here. One port will be the working
port, and the other will be the backup port. The system will automatically decide which port is the
working port, and which one is the backup port.
Enable Ring Coupling: you can enable the Ring Coupling function by checking this option.
Coupling Port: you can assign the member port for Ring Coupling here.
Set to be Coupling Backup Switch: you can set the switch as the master switch in a coupling
ring by checking this option.
Once you finish configuring the settings, click on Apply to save the configuration.
Note: When you enable the Super Ring function, you must disable the RSTP. The Super Ring
function and the RSTP function cannot be enabled at the same time.
How to Set Up a Super Ring?
Here we use 4 JetNet 4008s to form a Super Ring topology. Switch 1 is configured to be the
master switch, and the backup path will be decided by this master switch. In this example, we set
up the path on the bottom right corner to be the backup path.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-17
The settings of Switch 1.
The settings of Switch 2.
The settings of Switch 3.
The settings of Switch 4.
Note: Before you connect the backup path, you need to finish the settings described above.
Otherwise, it will cause a loop problem.
3-18 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
Can 3 Switches Form a Super Ring Topology?
Here we use 3 JetNet 4008s to form a Super Ring topology. Switch 1 is configured to be the
master switch, and the backup path will be decided by this master switch. In this example, we set
up the path on the right to be the backup path.
The settings of Switch 1.
The settings of Switch 2.
The settings of Switch 3.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-19
Note:Before you connect the backup path, you need to finish the settings described above.
Otherwise, it will cause a loop problem.
How to Set Up Ring Coupling?
As shown in the figure above, the Super Ring topology on the left is up-linked to the one on the
right via the Ring Coupling function, ensuring that both sides of the Super Ring topologies will not
loose connection with each other when the primary path fails. This Ring Coupling is established
by SWITCH 1, 3, 4, and 5. SWITCH 1 plays the role as the backup switch of this Ring Coupling,
and is responsible for deciding which path to be the backup path that is usually blocked.
SWITCH 1 also monitors the network status, and decides when to recover the blocked backup
path. The settings for the 4 switches are as follows:
The settings of SWITCH 1 for the Ring Coupling.
The settings of SWITCH 3 for the Ring Coupling.
The settings of SWITCH 4 for the Ring Coupling.
3-20 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
The settings of SWITCH 5 for the Ring Coupling.
Note: If you configure a JetNet as the master switch of the Super Ring and the backup switch of
the Ring Coupling, then this JetNet will consume a great deal of computing resources on
monitoring the network status. For this reason, please use different JetNets to be the master
switch of the Super Ring and the backup switch of the Ring Coupling.
QoS
In QoS section, you can configure the QoS settings of each port.
Oos Policy
You can select the Qos policy rule.
Using an 8,4,2,1 weighted fair queuing scheme: the JetNet will follow 8:4:2:1 rate to process
the packets in a queue from the highest priority to the lowest. For example, the system will
process 8 packets with the highest priority in the queue, 4 with middle priority, 2 with low priority,
and 1 with the lowest priority at the same time.
Use the strict priority scheme: packets with higher priority in the queue will always be
processed first, except that there is no packet with higher priority.
Priority Type
Each port has 5 priority types for you to select.
Port-based: the port priority will follow the default port priority that you have assigned – High,
middle, low, or the lowest.
COS only: the port priority will only follow the COS priority that you have assigned.
TOS only: the port priority will only follow the TOS priority that you have assigned.
COS first: the port priority will follow the COS priority first, and then other priority rule.
TOS first: the port priority will follow the TOS priority first, and then other priority rule.
Default Priority Type
This is to decide the default priority of each port.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-21
COS Priority: this is to map the COS priority (level 0~7) to port priority(4 levels).
TOS Priority: this is to map the TOS priority (level 0~63) to port priority(4 levels).
IGMP
The IGMP (Internet Group Management Protocol) is an internal protocol of the Internet Protocol
(IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP.
Enabling IGMP allows the ports to detect IGMP queries, report packets, and manage multicast
traffic through the JetNet. IGMP has three fundamental types of messages, as shown below:
Message
Description
Query
A message sent from the querier (a IGMP router or a switch) which asks for a
response from each host that belongs to the multicast group.
Report
A message sent by a host to the querier to indicate that the host wants to be
or is a member of a given group indicated in the report message.
Leave
A message sent by a host to the querier to indicate that the host has quit as a
3-22 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
Group
member of a specific multicast group.
You can enable IGMP protocol and IGMP Query functions here. You will see the information of
the IGMP Snooping function in this section, including different multicast groups’ VID and member
ports, and IP multicast addresses that range from 224.0.0.0 to 239.255.255.255.
Once you finish configuring the settings, click on Apply to save the configuration.
Security Manager
You can change the user name and the password here for security concern.
User name: you can key in the new user name here. The default setting is root.
Password: you can key in the new password here. The default setting is root.
Confirm Password: you need to type the new password again to confirm.
Once you finish configuring the settings, click on Apply to save the configuration.
Configuration Backup
In Configuration Backup section, you can restore the backup configuration into the JetNet. You
also can backup the configuration to the TFTP server as well.
TFTP Restore Configuration
You can restore EEPROM values from the TFTP server. Before you can do that, you must place
the backup image in the TFTP server, and then the JetNet will download the image back to the
flash.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-23
TFTP Server IP Address: you need to key in the IP address of the TFTP Server here.
Restore File Name: you need to specify the correct restore file name here.
Once you finish configuring the settings, click on Apply to save the configuration.
TFTP Backup Configuration
You can save the current flash ROM value from the JetNet to the TFTP server, then go to the
TFTP Restore Configuration page to restore the image value back to the JetNet.
TFTP Server IP Address: you need to key in the IP address of the TFTP Server here.
Backup File Name: you need to specify the correct backup file name here.
Once you finish configuring the settings, click on Apply to save the configuration.
TFTP Update Firmware
In this section, you can update the latest firmware for your JetNets. Before you do so, make sure
that you have your TFTP server ready and the firmware image is on the TFTP server.
TFTP Server IP Address: type in the IP address of your TFTP server here.
Firmware File Name: type in the file name of the firmware image.
Once you finish configuring the settings, click on Apply to save the configuration.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
3-24 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
Factory Default
In this section, you can reset the JetNets to the default settings as shown below:
Default IP address: 192.168.10.1
Default Gateway: 192.168.10.254
Subnet Mask: 255.255.255.0
Other settings will be set to disable or none.
Click on Default to reset your JetNets to the default settings.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
System Reboot
System Reboot allows you to reset JetNets’ software. Click on Reboot to reboot your JetNets.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
settings you made will be gone when the JetNet is powered off.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-25
Save Configuration
Save Configuration allows you to save any configuration you just made to the flash memory.
Powering off the JetNets without clicking on Save Configuration will cause the new settings to be
erased. Click on Save Flash to save your new configuration.
Rate Control
In this section, you can configure each port’s bandwidth rage and packet limitation type.
Limit packet type: you can select the packet type that you want it to be filtered. The packet
types listed here include broadcast/multicast/unknown Unicast packet, broadcast/multicast
packet, and broadcast packet only. The broadcast/multicast/unknown Unicast packet,
broadcast/multicast packet, and broadcast packet only are only for ingress packet. The egress
rate only supports all type packet.
Bandwidth: Port 1 to Port 8 support port ingress and egress rate control. For example, let’s
assume port 1 is 10 Mbps, you can set its effective egress rate to be 1 Mbps, and ingress rate to
be 500 Kbps. The JetNet uses the packet counter to control the number of packets coming in so
that the configured ingress rate can be achieved.
Ingress: here you can select the port effective ingress rate. The valid values are 1MB, 2MB, 4MB,
8MB, 16MB, 32MB and 64MB. The default value is “disable”.
Egress: here you can select the port effective ingress rate. The valid values are 128kbps,
256Kbps, 512Kbps, 1MB, 2MB, 4MB, and 8MB. The default value is “disable”.
Click on Apply to apply the configuration.
Note: Remember to click on the Save Configuration button to save your settings. Otherwise the
3-26 Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
Web-based Management
settings you made will be gone when the JetNet is powered off.
Note: QoS and Rate Control settings cannot exist at the same time.
Korenix JetNet Series Industrial Web-Managed Ethernet Rail Switch User’s Manual 3-27
4
Chapter 4
Troubleshooting
This chapter includes the information on general troubleshooting.
The following topics are covered in this chapter:
Incorrect Connections
¾
Faulty or Loosen Cables
¾
Non-standard Cables
¾
Improper Network Technologies
LED Indicators
Note: make sure you are using the correct VDC power suppliers (12 to 48 VDC) or power
adapters. Do not use power adapters with DC output over 48V. It will damage devices.
Note: select Ethernet cables with specifications suitable for your applications to set up your
systems. Ethernet cables are categorized into unshielded twisted-pair (UTP) and shielded
twisted-pair (STP) cables. Category 3, 4, 5 Ethernet cables are suitable for systems with 10
Mbps transmission speed. For systems with 100 Mbps transmission speed, Category 5 Ethernet
cables are the only suitable specifications for this environment. You also need to make sure that
the distance between each node cannot be longer than 100 meters (328 feet).
Note: if the power LED goes off when the power cord is plugged in, a power failure might occur.
Check the power output connection to see if there is any error at the power source. If you still
cannot solve the problem, contact your local dealer for assistance.
Note: use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cables for RJ-45
connections. 100Ω Category 3, 4 or 5 cables are for 10Mbps connections, and 100Ω Category
5 cables are for 100Mbps connections. You also need to be sure that the length of any
twisted-pair connection does not exceed 100 meters (328 feet). Gigabit ports should use Cat-5
or cat-5e cables for 1000 Mbps connections. The length does not exceed 100 meters.
Incorrect Connections
The ports on the JetNet can auto detect straight or crossover cables when you connect the
JetNet with other Ethernet device. For the RJ-45 connectors, use correct UTP or STP cables.
For 10/100 Mbps ports, use 2 pairs of twisted cables, and 4 pairs of twisted cables for Gigabit
1000T ports. If the RJ-45 connectors and the cables are not correctly connected, the link will fail.
For fiber connection, make sure that the fiber cable mode should match the fiber module.
Faulty or Loosen Cables
Look for loosen or obviously faulty connections. If no such errors are found, make sure the
connectors and the cables are tightly connected. If that does not correct the problem, try a
different cable.
Non-standard Cables
Non-standard and incorrectly-wired cables may cause numerous network collisions and other
network problems, and can seriously impair network performance. A category 5 cable tester is a
recommended tool for every 100Base-T network installation.
Improper Network Technologies
It is important to make sure that you have a valid network topology. Commonly-made topology
mistakes include excessively long cable length and too many repeaters (hubs) between end
nodes. In addition, you should make sure that your network topology contains no data path loops.
Between any two end nodes, there should be only one active cabling path at any time. Data path
loops will cause broadcast storms that will severely impact your network performance.
LED Indicators
The JetNet can be easily monitored via the LED indicators located on the JetNet front panel to
assist in identifying common problems and to help you find possible solutions.
If the power LED indicator does light on when the power cord is plugged in, you might have a
problem with power outlet, or power cord. However, if the JetNet powers off after running for a
period of time, check for loosen power connections, power losses or surges at power outlet. If
you still cannot resolve the problem, contact your local dealer for assistance.
4-2
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual
A
Appendix A
Specifications
Standards
IEEE 802.3 10BaseT Ethernet
IEEE 802.3u 100BaseT(X) Fast Ethernet
IEEE 802.3x Flow Control and back pressure
IEEE 802.1p class of service
IEEE 802.1Q VLAN
Protocols
CSMA/CD
Technology
Store and Forward
Transmission Rate
14,880 pps for Ethernet port
148,800 pps for Fast Ethernet port
MAC Address Table Size
2K MAC address table
Memory Buffer
1M bits
LEDs
„
„
Per port: Link/Activity (Green)
Full duplex/Collision (Orange)
Per unit: Power 1, Power 2 , Power(Green)
Fault(Red), RM(Ring Master, Green)
Network Cables
10BaseT: twisted-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m)
100BaseT(X): twisted-pair UTP/STP Cat.5 cable
EIA/TIA-568 100-ohm (100m)
Power Input
12 to 48 VDC, redundant dual DC power inputs with reverse polarity
protection, and a removable terminal block for master and slave VDC
power inputs.
Power Consumption
6 watts
Back-plane
1.6Gbps
Operating Temperature
-10℃ to 70℃ (14℉ to 158℉)
Operating Humidity
5 to 95% Relative Humidity, non-condensing
Storage Temperature
-40℃ to 85℃
Dimensions
54 mm (W) x 135 mm (H) x 105 mm (D)
EMI
FCC Class A
EMS
CE EN6100-4-2, CE EN6100-4-3, CE EN6100-4-4, CE EN6100-4-5,
CE EN6100-4-6
Safety
UL, cUL, CE/EN60950, IP-30
Stability
A-2
IEC60068-2-32 (free fall test), IEC60068-2-27 (shock test),
IEC60068-2-6 (vibration test)
Korenix JetNet 4000 Series Industrial Web-Managed Ethernet Rail Switch User’s Manual