Chembond CL400

MAKERS OF ADHESIVES, SEALANTS, AND RELATED
PRODUCTS SINCE 1958.
Chembond CL400
(Construction Adhesive)
- TECHNICAL DATA SHEET -
- TECHNICAL DATA SHEET Chembond CL400
MAKERS OF ADHESIVES, SEALANTS, AND RELATED
PRODUCTS SINCE 1958.
Adress: 8428 Shepard RD SE
T2C 1R6, Calgary, AB
Phone: [403] 252.7803
Fax: [403] 252.2384
(Construction Adhesive)
PRODUCT DESCRIPTION
Chembond is a high quality, high solids rubber base adhesive. It is designed to meet
the high speed production requirements of both on-site and factory built construction.
This adhesive exhibits extremely high ultimate shear strength, outstanding aging
characteristics, excellent moisture and heat resistance and it reduces sound transmission as
well as labor and material costs, in a broad range of interior and exterior applications.
PROPERTIES
Base
Color
Weight/Gallon
Solids Content Flash Point (TOC)
Consistency (30,000 - 35,000 cps) Coverage Bonding Range
Clean-up
Conforms to
- synthetic elastomer
- buff/cream
- 11.0 + or - 0.2 pounds
- 60 + or - 2%
- 20o F
- creamy mastic - gun grade
- 1/8” bead - up to 1450 lineal feet/
gallon - 1/4” bead - up to 350 lineal
feet/gallon
- up to 30 minutes at 72o F
- petroleum naphtha
- CAN/CGSB-71.26-M88
SHEAR STRENGTHS
Method - ASTM D-906
Cure: 2 days at 50o C, 4 days at rm. temp.
Pine to Pine Bonding
- 546.6 lbs/sq. in.
Dry Pine to Dry Pine (Cure: 28 days at 100o
- 598.1 lbs/sq. in
F)
Dry Pine to Frozen Pine (Cure: 7 days at 0o F) plus - 436.2 lbs/sq. in.
21 days a 40o F
Dry Pine to Dry Pine ( Cure: 500 hrs at
- 616.0 lbs/sq. in.
150oF
AFG-01 Oxidation resistance test (pass, no fracture on free film bent around mandrel)
Phone: (403) 252-7803
|
Fax: (403) 2522384
|
www.chemtron.ca
APPLICATION
Chembond is designed for trowelling or extruded applications. Surfaces to be bonded must be free of
dirt, oil, grease, rust or foreign matter. It is generally recommended that your component be positioned
and placed within 10 minutes after the Chembond has been applied. Press components firmly in order to
rupture the slight surface skinning that has occurred; this will also allow a large contact area to be wetted.
Use clamps, nails or supplemental fasteners to hold component in proper position, until Chembond is set
(usually 24 hours).
It is also generally recommended that Chembond should not be applied to various components at
temperatures lower than 0o F, after being stored at room temperatures.
When bonding subfloors, it is recommended to apply Chembond for one sheet at a time, nailing the sheet
perimeter on 6” centers and the sheet intermediate points on 12” centers for maximum strength.
Because of the flammable nature of Chembond, we recommend that you keep the product away from heat,
sparks, and open flame. Avoid prolonged breathing of vapor or prolonged contact with skin, due to the
solvents present in the uncured adhesive - use in adequately vented area.
CAUTION
Do not use Chembond on substances susceptible to attack by solvents, eg. polystyrene foam, vinyl board
materials.
WARRANTY
RECOMMENDATIONS FOR USE OF THIS PRODUCT ARE BASED ON RELIABLE TESTS, SINCE DESIGN AND
CONDITIONS OF INSTALLATION ARE BEYOND OUR CONTROL. NO GUARANTEE OR APPLICATION IS
IMPLIED. OUR LIABILITY FOR ANY DEFECT OF THE MATERIAL IS LIMITED TO REFUND OF THE PURCHASE
PRICE ONLY.
Phone: (403) 252-7803
|
Fax: (403) 2522384
|
www.chemtron.ca