MKPLAY VAULT MINI TRAMPOLINE SERIES

Vault Mini Trampoline and Safety Net
MKPLAY VAULT MINI
TRAMPOLINE SERIES
55 INCH (4.5FT) TRAMPOLINE
WITH SAFETY NET ENCLOSURE
Weight Limit – 100lbs (45kg)
Person Limit – 1 Persons
Age Limit – 3-6 years
1
Vault Mini Trampoline and Safety Net
TABLE OF CONTENTS
Parts List
03
Trampoline Assembly Instructions
04
WARNING
Please read this manual prior to assembly and use.
Keep this manual for future reference.
For use by children ages 3 to 6 years ONLY.
The maximum user weight is 45kg.
ADULT ASSEMBLY REQUIRED – Contains small parts, sharp points
and sharp edges. These pieces can be a CHOKING HAZARD for young
children, especially under 3 years.
2
Vault Mini Trampoline and Safety Net
PARTS LIST
The list of parts for the 55 inch trampoline is below. Please check that you have all parts
prior to assembly.
Parts
Quantity
Red Pad Cover with Black Mesh Skirt
1
Jump Mat
1
Safety Net
1
Black Rope/Cord
1
White Elastic Cords
30
Screws
30
Screw Driver
1
Curved Pole
6
Lower Enclosure Pole (with Grey/Black Foam)
6
Upper Enclosure Pole (with Red Foam)
6
Straight Leg Pole
6
3
Vault Mini Trampoline and Safety Net
INSTALLATION STEPS
Installing the Base Frame
Step 1: Start by connecting two of the curved poles
together into an arc. Then, add the remaining 4 curved
poles together to form a full circle. If it is difficult to
assemble the last two poles together, then stand on the
frame edge (with the two poles to connect at your hand
height), then press downward on the two poles while
joining together.
Step 2: Lay the circular frame flat on the floor (both
sides are identical so it doesn’t matter which way is up).
Attach the straight leg poles into each of the 6 holes in
the circular frame. Line up the holes in the circular frame
with the holes in the straight legs and insert a screw into
each connection. Do not overtighten the screws.
TIP: The provided screwdriver is not the best quality. It
is recommended to use your own screwdriver.
Step 3: The base frame is now installed. Turn over the
base frame so that it is now standing on the straight leg
poles.
4
Vault Mini Trampoline and Safety Net
Installing the Jump Mat
Step 4: Lay out the jump mat in the centre of the circular frame.
Step 5: Then, slide one of the white elastic cords from
right to left through the loop in the mat as shown in the
picture
Step 6: Use your left hand to stretch the loop end of the
cord OVER the top rail and your right hand to pull the
“closed” end of cord UNDER the top rail. Then pass the
closed end through the loop as shown in the picture.
Step 7: SLOWLY release the loop end of the cord so
that it tightens around the closed end, locking the
elastic cord in place.
TIP: If you like, you can switch the right hand/left hand instructions above (if it’s easier for you).
However, the over/under instructions still remain the same.
5
Vault Mini Trampoline and Safety Net
Step 8: From the 1st attached cord, count around the jumping mat to the 16th loop and repeat
steps 5-7 to attach the 2nd cord directly across from the 1st cord.
Step 9: Next, count back around the jumping mat 8 loops and repeat steps 5-7 attaching the
3rd cord about half way between the 1st and 2nd cords.
Step 10: Then from the 3rd attached cord, count around
the jumping mat 16 loops and repeat steps 5-7.
Step 11: Continue connecting the remaining cords to the
jump mat, but always connect a cord and then switch to
the opposite side of the mat to connect the next cord.
Installing the Pad Cover
Step 12: Lay the pad cover over the jump mat and
elastic cords. Carefully position each of the 6 openings
in the pad cover over their corresponding enclosure
pole socket, as shown.
6
Vault Mini Trampoline and Safety Net
Step 13: Carefully work the black lower mesh skirt
(attached to the pad cover) down around the entire
perimeter of the trampoline, on the outside of the legs.
Step 14: Align the grommet (small hole) attached to the
bottom of the lower mesh skirt with the hole near the
base of the circular frame leg and secure with a screw.
DO NOT OVER-TIGHTEN. Repeat with 5 more screws
until the entire mesh skirt has been connected to the
lower holes in the trampoline legs.
Installing the Safety Net Poles
Step 15: Insert the smaller diameter end of an upper enclosure pole (red foam pole) into the
larger diameter end of a lower enclosure pole (black foam pole) and align the screw holes. You
may need to slide the preinstalled foam sleeves up or down to gain access to the ends of
the pole.
Step 16: Insert a screw into the connected poles and
tighten. DO NOT OVER-TIGHTEN. Repeat step 15
to complete the remaining set of upper and lower
enclosure poles.
7
Vault Mini Trampoline and Safety Net
Step 17: Insert the bottom end of the enclosure pole
assembly into the hole in the circular frame, as shown.
Align the holes, insert a screw, and tighten. Once again,
do not overtighten. Repeat until all enclosure poles have
been connected to the circular frame.
Installing the Safety Net
Step 18: Take out the net, lay it out, and make sure that the zipper entrance is at the bottom of
the laid out net.
Step 19: Locate the 6 black patches with grommets (small holes) that are sewn into the top of
the safety net. Carefully place one of the patches over the top of one of the safety net poles
so that the small hole in the net patch is aligned with the hole at the top of the safety net pole.
Please use care so that the mesh does not tear.
Step 20: Insert a screw and tighten (but not
overtighten). Repeat Step 19 until all black patches at
the top of the safety net are connected to each of the
safety net poles, and screwed in. When finished, the net
should hang down straight (not twisted), and should be
hanging down on the inside of the safety net poles.
Step 21: Locate the upper and lower sets of velcro loops sewn to the safety net.
Step 22: Tightly wrap both the upper and lower loops
around the safety net poles to secure in place. Continue
until all loops have been connected.
8
Vault Mini Trampoline and Safety Net
Securing the bottom of the Safety Net
Step 23: Take out the black rope. This will be used to fasten the bottom of the safety net
underneath the mat. For this step, you can either lie on your back underneath the trampoline,
or tilt the trampoline CAREFULLY onto its side.
Step 24: On the inside of the safety net poles, carefully pull the grommets (small holes) on the
bottom of the safety net down underneath the jump mat. You can do them all at once or one at
a time (whichever is easier).
Step 25: Once each hole in the bottom of the safety net is pulled underneath the mat, loop the
rope through each hole and then tie the two ends together once you get to the end. The tighter
you pull the two ends together, the tighter the safety net will be (do not make too tight). There
should be more than enough rope for this step.
GREAT JOB, YOU’RE DONE!
YOU HAVE NOW COMPLETED THE INSTALLATION OF YOUR
TRAMPOLINE. ENJOY!
9